Search Documents

By C. C. Knox

In Kiowa County, Okla., extensive deposits of clay are closely associated with pre-Cambrian anorthosites and gabbros. Investigation by the Bureau of Mines, including 1,723 feet of auger drilling, has shown the presence of very large quantities of clay containing between 20 and 25 percent alumina. All of the material contains large amounts of impurities, and even the best clays, selected for their relatively low content of iron, titanium, and magnesium, are unsuitable for the production of alumina by the sulfuric-acid process The soda-lime process gave somewhat better results, the product being nearer specification for commercial alumina. The clays are not amenable to beneficiation by simple sedimentation processes, and the alumina content could not easily be increased to produce material suitable for any alumina process.

Jan 1, 1948

By Paul Hopkins

The following methods have been selected from a large number tried while assaying several hundred samples of placer concentrates. It is thought that some of these methods may be useful to those who are required to assay similar products containing large quantities of metallic articles, such as jeweler's sweepings. No great difficulties will be encountered in assaying black sand from beaches or river bars. Such samples require care in grinding and sifting so that no oversize particles of gold or platinum are lost. It is also necessary to have sufficient silica in the flux to form a fluid slag with the excess of iron, magnesium, or chromium which such samples contain. It is much more difficult to assay black sands, or concentrates, produced in large-scale placer-mining operations. These products are usually much harder and more abrasive than the beach black sands. They also contain numerous metallic particles resulting mainly from wear on the mining machinery. These particles consist chiefly of iron or steel but also contain lead, copper, and alloys such as babbitt, solder, brass, ferrosilicon, etc. Fairly large particles of gold are often found. Some samples will contain as much as 10 percent of such metallic particles. It is not feasible to remove the particles of iron with a magnet and discard them, as they invariably contain gold, sometimes a considerable amount. This gold is attached to the iron particles by rust or wedged into cavities. Scraps of sheet iron are often found which have become tightly folded or rolled and contain gold or amalgam within the folds.

Jan 1, 1934

By N. A. Eilertsen

Eastern Aroostook County, Maine, contains an enormous tonnage of manganese widely distributed in manganiferous sedimentary beds composed of hematitic shale, hematitic slate, and laminated siliceous carbonate rock. The bedded deposits range in thickness from several feet to over 150 feet. Manganese minerals that occur as silicates and carbonate are so minute that they cannot be concentrated by present methods of ore dressing. From a hydrometallurgical standpoint, the deposits can best be classified by amenability to acid leaching. The deposits of Aroostook County are in three geographical groups (see fig. l), designated as the northern, central, and southern districts. At least 13 deposits are known to occur in the latter district, which covers an Ewes about 8 miles wide and 15 miles long. The Littleton Ridge deposit, on the northern boundary of the southern district, previously examined by geologists from the State and Federal Geological Surveys on the farms of Donald H. Haggerty and David A. Abernethy, was pointed out in reports as being possibly the richest and largest in the southern district. The Bureau of Mines sampled this deposit by surface trenching and diamond drilling from May 1 to September 30, 1951. A total of 23 trenches was bulldozed, aggregating 5,355 linear feet, of which 8 trenches were sampled by cutting 185 channel samples over a linear distance of 1,820 feet.

Jan 1, 1955

By R. N. Love, L. Goldman

"INTRODUCTION When tannin is present in a boiler water, it causes certain difficulties in many analytical testing procedures because of its colloidal action in interfering with the removal of suspended matter by filtration and also because of the color it imparts to the boiler water.For example, in any test for phosphate in boiler water the first step is to filter out of the sample all sludge and suspended solids. Calcium phosphate in the sludge would give high results if not completely removed. If tannin is present in the sample, the sludge and suspended matter tend to pass through the filter paper so that it is difficult to remove it all. It may even be that tannin makes some of the suspended material in the sample completely nonfilterable. If this is true, it would be necessary to destroy or remove the tannin from the sample before filtering to get complete removal of calcium phosphate from the sample. In addition, if the test used is a colorimetric one, the tannin causes interference by its own color.As the calorimetric phosphate test is so convenient for control purposes and the use of tannin for boiler water treatment has become common, it has become necessary to develop suitable methods for employing the colorimetric phosphate test for boiler waters containing tannin. In this paper three different methods for doing this arc described and studied."

Oct 1, 1946

By R. A. Isberg, D. A. Parrish, H. Kramer

This report describes the design and implementation of UHF radio and closed-circuit television systems in the Black River room and pillar limestone mine near Butler, Pendleton County, Kentucky. Prior to designing the radio system, measurements of signal attenuation on 812 and 466 mHz were made in the slope tunnel and in the straight and level crosscuts in the mine. Two distributed antenna systems fed by two sets of base stations provide approximately 75% coverage of the mine. Passive reflectors are used for extending signals into intersecting crosscuts and two-way signal boosters will be used to extend signals to the perimeter and obstructed areas of the mine. Fourteen mine vehicles were equipped with mobile radios equipped with digital identification, alarm and status encoders. Fifteen portable transceivers also were used. Six closed-circuit television cameras provide surveillance of critical transfer points of the belt conveyor system, and the loading dock at the base of the slope and an ash disposal area in the mine. Two-way radio communication and closed-circuit television have saved considerable man. hours, increased production, reduced maintenance costs and enhanced safety. Innovative developments were the use of passive reflectors and two-way signal boosters for extending signals into intersecting crosscuts, development of lightweight signal margin measuring equipment, modifications of mobile digital encoders to automatically send status information from mine vehicles such as numbers of loads of ore delivered, hot engine, etc., and the use of CATV technology for multiplexing audio, digital and video signals onto coaxial cables from the surface to the mine.

Jan 3, 1981

By E. J. Matson

The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. The Rush Creek lead-zinc deposit, Mono County, Calif. (fig. 1), was examined by W. T. Benson in July 1944 and again in September 1945 by D. W. Butner, engineers of the Bureau of Mines. From the results of these preliminary examinations, a core-drilling program (fig. 2) was started in August 1946 and continued until November 1946, when work was stopped on account of inclement weather. Field work was again started in May 1947 and completed in June 1947. The drilling program was laid out to develop the horizontal .and vertical extensions of showings exposed in surface pits.

Jan 1, 1949

By Ernest W. Johnson

Diamond, drilling of some blast holes in stoning operations is practised in at least two iron mines in the Lake Superior district - the Soudan mine of the Oliver Iron Mining Co., on the Vermilion range at Soudan, Minn., and the Anvil-Palms mine, operated by Pickands, Bather & Co., on the Gogebic range at Bessemer, Mich. Diamond drilling, at the Soudan nine has partly replaced percussion drilling because of the extreme hardness of the ore and of the lean formation. According to Wolff,4/ the jasper or lean formation in this mine is the hardest rock regularly drilled in any commercial operation.

Jan 1, 1945

By Earl R. Maize

Epoxy and polyester-type resins were injected into coal-mine roof strata of the thick Freeport coal seam in Allegheny County, Pa., at test sites in roof that had been exposed several weeks, in newly exposed roof, and in strata over solid coal. Test results indicate that the method of strengthening bituminous-coal-mine roof by injecting a bonding material into the roof strata can be developed into a safe, efficient support system. If roof bonding will become a standardized method of roof support and reinforcement or if it can be effective when used with other types of roof support can be determined only by extensive experimentation in various coal beds. Observations and conclusions are shown at the end of this report.

Jan 1, 1959

By A. U. Miller

Protection against fire is a greater problem at a coal mine, than at an ordinary industrial plant. Generally mines are located in isolated districts and do not have the protection of city fire departments; consequently fire fighting aquipment must be installed by the mining company. Fire protection around a mine is just as essential as it is in the city.. and undoubtedly is more important if the fire should be underground where many lives would be endangered and all means of escape cut off. A surface fire can generally be attacked from any angle, but an underground fire can be attacked only as conditions will permit.. U. S. Bureau of Mines engineers have investigated many serious mine fires that undoubtedly could have been extinguished in incipiency if a fire extinguisher or fire hose and water had been readily available. In past years very little attention was given..to fire fighting equipment and organization around mines, but in recent years three gen a derde hange of opinion among many of those engaged in mining, and nearly all up-to-date mining companies now have some kind of fire protection about their mine Probably the first company in Illinois to install regular fire fighting equipment and effect a fire fighting organization at its mines, was the Madison Coal Corporation, which operates several mines in Illinois. The main office of this company is in Chicago and the general field office is at Glen Carbon, Ill.

Jul 1, 1930

By J. T. Popp, C. M. McCulloch

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con- tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By Martyn F. Roetter

The objectives of the work described in this report are to determine the communications requirements and need for communications, both for voice and control, on longwalls, and to make recommendations for longwall communications equipment and systems. These recommendations are designed to guide the future development of longwall communications. Information necessary for the accomplishment of this work has been gathered by a series of visits to longwall mines and discussions with longwall mine operators, as well as with suppliers of longwall communications and mining equipment and with Bureau of Mines personnel. In addition, it has proven possible, through personal interviews and literature evaluation, to gain an understanding of the experience and attitudes towards longwall communications in countries where longwall mining is far more widespread than in the U.S., namely the Federal Republic of Germany, the United Kingdom, France and Belgium.

Jan 1, 1976

By J. L. Buckley

A survey of previous underground mine fires revealed a number of reported fires may have been caused by malfunctioning stationary electrical equipment. Therefore, an evaluation of conventional fire protection systems was conducted to determine their usefulness in the protection of this equipment. To simplify the problem and facilitate the handling of data, the under-ground mine was divided into nine work areas. Representative combustibles and associated hazards characteristic of each area were identified. Conventionally available fire protection systems were then examined and evaluated to determine engineering and cost feasibility, effectiveness and reliability for the development of fire protection guidelines which could be used within the nine areas of interest.

Jan 1, 1976

By Joseph T. Singewald

The possible value of the red hematite iron ore of the southern Appalachian States, if some practicable method of concentrating it could be devised, has long been recognized. The ore is very low grade, and although in enormous quantities, particularly in the States of Alabama, Tennessee, and Georgia, is only at a few points rich enough to work, and even the best of it ranks among the lowest grade iron ores being mined in the United States. A cheap method of beneficiating this ore would make enormous quantities available and vastly increase the iron-ore resources of the country. However, this low-grade ore in effect constitutes a potential iron reserve, and as long as ample quantities of ore can be obtained elsewhere the question of its utilization does not demand immediate notice. Where these ores are in part of workable grade, however, a problem of more immediate importance arises which, from considerations of economy and prevention of waste in their mining, ought to be solved or, at least, attacked as quickly as possible. Where these ores are being worked they are usually intimately associated with lower-grade material that in mining is left behind. The difficulty and expense of going into ground broken by old workings makes the recovery of this lower-grade ore practically impossible and it is lost forever. Success in concentrating the red ores, therefore, would save material that is now being irretrievably lost. The successful large-scale concentration of law-grade ore in the last few years on the Lake Superior iron ranges should encourage the attack of similar problems in the Birmingham district.

Jan 1, 1917

By R. L. Grayson

"Compliance standards for respirable dust, which are reduced because of high quart: concentrations, have become an industry-wide problem. Research on the physical and chemical character of quart-classified particles in respirable coal mine dusts indicates that they may exist in intermixed layers or may be coated by clay or coal material. The relative amount of intermixing varies with the coal seam being mined. If most of the quart: particles of a mine dust are ""pure,"" then the dust may have a high fibrogenic risk potential because of truly free silica and the compliance standard should be lowered. lf, however, quart: is locked inside another material matrix, or coated, a reduced compliance standard may not be appropriate.Although much research has been done on coal workers' pneumoconiosis (CWP) over the past decades, the etiologic agents of the disease still have not been pinpointed. The predominant methods of characterizing respirable coal mine dusts were bulk analysis techniques for determination of elemental and mineralogical concentrations, the results of which were used in statistical analyses to determine relationships between dust composition and the occurrence of CWP. These methods are incapable of finding the etiologic agents in the dust primarily because of complicated and confounding physiochemical factors, which may be discovered if the focus of characterization was done on a dust particle level.The SEM/EDXA-based research discussed here shows a significant difference in the number of ""pure"" quartz particles in respirable dusts collected from different mines. Some of the results have been reported previously (Grayson, Andre, and Simonyi, 1988). Concurrent research by other investigators (Wallace et al., 1989) demonstrates an SEM/EDXA-based methodology to pinpoint the location of the ""contaminating"" substance(s ) in a quartz-classified particle. The research of the European Economic Community has also begun analyses on the respirable-dust-particle level (Robock and Bauer, 1988).Since the compensatory and intangible costs of CWP are substantial in the United States, it is important that the etiologic agents be determined and then either controlled or neutralized in a cost-effective way. This line of research is especially important consid-ering the forecasted. near-term growth of coal production and the evolution of high productivity longwall panels (an immediate problem in compliance) and continuous mining sections ( a probable future problem).This need has been accentuated now that nearly all respirable dust samples submitted to MSHA are analyzed for free silica (Tomb, Parobeck, and Gem, 1986). Today a real problem exists in the coal industry, both underground and surface, because of high quartz levels in respirable dusts causing substantially reduced compliance standards (Murphy, 1989).The combined results of the respirable dust particle investigators indicate that conventional bulk sample analyses may not faithfully represent the amount of biologically available or active quartz in all mines with a high level (greater than 5% ) of quartz in the dust For example, some mine dusts might contain predominantly occluded (or coated) quartz particles where bulk analysis would result in anomalously high ""free silica"" measurements. The same result would occur when quartz particles are intermixed substantially with other minerals that can alter the surface of the composite particle away from a quartz-behaving character."

Mar 1, 1992

By J. P. Capp

The Federal Bureau of Mines and the Alabama Power Company conducted an experiment in underground gasification of coal at Gorgas, Ala. involving the use of hydraulic fracturing to increase the air acceptance of a coalbed for the introduction of combustion air and removal of product gases. Air acceptance is defined as the flow rate of air which can be injected into the coalbed at 65 p.s.i.g. This was the second time the hydraulic-fracturing technique was used at Gorgas. Sand suspended in a heavy oil served as the fracturing fluid in the first experiment; in the second the sand was two to six times larger and was suspended in a water-starch gel. In addition to providing further tests of the underground-gasification process, the purpose of the second experiment was to determine the effects of the larger sand and greater volumes of a water-base fluid on (1) the extent of the fractured area, (2) the air acceptance of the coal, and (3) the rate at which a gasification path could be carbonized (linked) through the coal, and to compare these results with those of the first experiment. The coal was fractured by injecting 11,000 lb. of sand and 33,580 gal. of water and water-gel at 200 to 600 g.p.m. and 900 to 1,000 p.s.i. The fluid fractured the coal and the sand served as a propping agent to hold the cracks and crevices open. Pressures during the fracturing operation at test boreholes indicated that the fracturing fluid extended only about 150 ft. from borehole H, the point of application of the fracture. Injection of air revealed that the air acceptance of the coalbed within this e t was materially increased. On the other hand, increased air acceptance also was noted at boreholes up to 280 ft. from borehole H and at the electrolinking area 300 to 400 ft. away, indicating that the fracture effects extended considerably farther than was evident from observation. Similar effects were noted at approximately the same distances after the first hydraulic fracture.

Jan 1, 1961

By James F. Devine

The radial, vertical, and transverse components of particle velocity were recorded by Bureau of Mines investigators along gage arrays extending in one or two directions for 145 to 3,170 feet at five quarries. Of the 39 quarry blasts, 12 were instantaneous blasts, 5 were of the one hole per delay type, using millisecond delayed caps, and 22 were multiple hole per delay type employing millisecond delay detonating fuse connectors. Charge weight per hole ranged from 8 to 1,500 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 25 to 4,620 pounds.

Jan 1, 1966

By Richard L. Unger

The Bureau of Mines entered into a cooperative agreement with an eastern Kentucky coal mining company to comprehensively redesign the flow of equipment and supplies throughout its underground mines. Items were tracked from delivery to the warehouse and from surface storage areas to their final usage locations underground. Three underground mines were visited, and a great variety of tasks were videotaped for subsequent laboratory analysis. Of particular interest were tasks that required manual handling of the supplies or equipment components. Activities such as handling daily supplies (concrete blocks, rock dust, and cross- beams) and handling or lifting the continuous miner power cable were determined to be the most hazardous. Recommendations to the company included redesigned surface storage areas to facilitate the use of forklift vehicles to load the underground supply cars. Designs were also developed for different mechanical- assist devices to help in unloading the supply cars underground and to handle equipment maintenance tasks underground. Additionally, the videotapes of the underground manual handling tasks became the basis for simulating those activities in controlled laboratory conditions. This testing will contribute to developing guidelines for proper lifting techniques for low-seam coal mines.

Jan 1, 1986

By Laxman S. Sundae

A U.S. Bureau of Mines designed and fabricated in-seam tester (1ST), retrofitted with a dust shroud, was used to establish a respirable dust index (RDI) and to determine cutting forces from a variety of bit types in four coal mines and a salt mine. Results from cutting tests at four coal mines showed that radial bits required the lowest cutting force and the least specific energy. Generally, for each conical bit the RDI and cutting force increased when the included bit tip angles increased from 70° to 90°. During field tests it was not possible to measure the total quantity of respirable dust produced by each cut; therefore, attempts were made to determine the amount of dust that became airborne from each test cut. The test results show that the quantity of airborne respirable dust is very erratic and cannot be related to bit type. Two statistical methods were employed to analyze RDI, but no correlation was found between the RDI and bit type. Despite scatter in test results for RDI, significant difference was found in RDI generated in four coal seams. In general, RDI increased with the increased cutting force for each coal seam from mine 1 through mine 4.

Jan 1, 1989

By Leonard F. Heising

At the Groveland mine iron ore is mined by open-pit methods and concentrated by means of spirals and flotation. A brief history of the mine and its early development is given. The ore deposit is described, with emphasis on those physical characteristics that affect the choice of mining and milling methods. Development and mining, which include breaking ground, loading, transportation, engineering, and operating control, are explained, and the milling method is described Mining and milling costs are given in percent of total cost.

Jan 1, 1963

By T. Bieniawski

"INTRODUCTION The Congress theme ""Improvement of Mine Productivity and Overall Economics by Modern Technology"" is probably beat: addressed by the subtheme allocated to this Plenary Session. It is appropriate that .Theme 1 emphasizes the simple point that effective use of geotechnical information is the key to improving mine productivity. In essence, this means that: (1) geological and geomechanics, (rock mechanics) data must be collected in sufficient quantity and of high quality; (ii) data interpretation must be performed specifically for purposes of engineering design; (iii) innovative design approaches should be used to bring about Improvements in productivity and safety.While, each of these three aspects .may: seem obvious to any mining engineer it is a fact that the above sequence is seldom followed and as a result, mining engineering not infrequently lags, behind other branches of engineering when it comes to design creativity, efficiency and safety.. . After all, mining is still-one of the most hazardous occupations and we are gathered here to discuss, at the highest world professional forum, how to use more effectively the modern technology. This however, does not mean that mining engineers are less capable than other engineers or that their achievements are any lesser; far from it! Mining engineers are the cream of the engineering society on whose efforts depends the welfare of mankind. Moreover, they have produced minerals and coal evergrowing quantities against evergrowing difficulties. Yet, we must and can become even better because we are not making full use of the modern technology and rock mechanics knowledge already at our disposal, and. we are not being innovative enough to the full extent of .our capabilities."

Jan 1, 1989