Search Documents

By H. E. Powell

The magnetic susceptibilities of 34 manganese-bearing minerals were determined. The source of each sample and petrographic, spectrographic, and chemical analyses are given. Included are values for ismorphous series showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

By D. W. Frommer

Composite samples of nonmagnetic taconite from the western Mesabi range were evaluated by reductive roasting, fine grinding, and magnetic separation to determine potential sources of concentratable material. Although large tonnages of nonmagnetic taconite are known to occur in the western Mesabi district, these materials are not as yet a commercial source of iron ore. The technique employed permits the evaluation of individual composites and blocks of composites in terms of responsiveness to a process of potential commercial significance. The 159 composites, from open-pit mines located between Grand Rapids and Chisholm, Minn., were evaluated in the following sequence: 1. Minus 8-mesh material was roasted at 500° C. in hydrogen. 2. The roasted are was ground to one or more sizes in the minus 100-to minus 400-mesh range. 3. The roasted ground ore was magnetically separated in a Davis tube. 4. Composites were classified according to degree of grinding required to produce minimal concentrates. (Minimal concentrates are herein defined as those containing less than 10 percent silica, and responsive composites as those yielding minimal concentrates.)

Jan 1, 1962

By Hal D. Peterson

In research sponsored by the Bureau of Mines, a technique was developed for simulation of heap leaching on uranium ores. The equipment used for this simulation consisted of 2-ft-diam columns, constructed in sections, such that ores as coarse as minus 4-in could be treated in bed depths ranging from 8 to 18 ft with test condition variations. The technique consisted of the separate steps of ore preparation, column loading, charge wetting, leaching, washing, and residue recovery. For the ores studied, sulfuric acid was found to be generally superior to alkaline lixiviants. The rate of uranium extraction by acid leaching proved" to be primarily a function of percolation rate, alkalinity of the ores and oxidant requirements of the ores. Column leaching was closely comparable to field-scale heap leaching in terms of uranium extraction rate and recovery results. Acid and oxidant requirements were lower for the field-scale operation. All column tests, as well as the field-scaly heap, achieved in excess of 96-pct uranium extraction on a Bear Creek, Wyoming ore.

Jan 1, 1985

By R. A. Beall

This paper summarizes the development of a furnace for producing titanium castings. The general problem is outlined and chronological details are given on the construction and operation of four different casting furnaces, all utilizing consumable-electrode arc heating and water-cooled copper crucibles. Of the two methods of pouring, the tilt-pour technique has been more satisfactory than bottom tapping. Mold design, electrode fabrication, and deep-pool production are discussed. INTRODUCTION In the early summer of 1953 the Bureau of Mines was contacted by the Department of the Army through Watertown Arsenal to explore the possibility of conducting research on casting titanium metal. The objective of the program was "to develop a technique for producing formed castings of titanium metal not less than 40 pounds in weight and without introduction of deleterious contamination."

Jan 1, 1956

By Ovsei Volberg

Motion capture involves recording the position and global orientation of joint sensors of a real object, in most cases a real person performing some human activities. This information is usually recorded at uniformly spaced instances of time, or as it is often called frame-by-frame. Then the recorded motion data sets are processed and mapped into a skeleton hierarchy of a virtual, computer simulated human figure to control the motion of the virtual human in the computer simulation. In the first part of the paper we review several new techniques developed to facilitate the manipulation, noise reduction, storage and reuse of captured data, which have a potential to reduce the overall cost of motion simulation and improve its realism. In the second part of the paper we consider the real life problem of reducing a worker?s risk from being hit by underground mining machinery in a confined space. We formulate a set of requirements to motion editing for this particular task and analyze the limitation of existing techniques

Jan 1, 2000

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1987 was $446.6 million, an increase over that of 1986 and the first increase in 3 years. Alabama was second in the Nation in production of bauxite and ferroalloys; third in bentonite, crushed dolomite, crushed marble, and fire clay; and fourth in masonry cement. Trends and Developments.-Employment in the minerals industry remained relatively low for the second year even though the overall unemployment rate dropped to 7.9% by December. Employment in mining and primary metals dropped about 10% and 2%, respectively.

Jan 1, 1989

By John B. Knaebel

This paper, describing the milling operations of the St. Joseph Lead Co. at Balmat, N. Y., is one of a series of similar papers being prepared by the United States Bureau of Mines on practice at various mills in the United States, Canada, and Mexico. The company also operates a mine end mill at Edwards, 12 miles northeast of Balmat. Mining practice in the district, as exemplified at the Edwards mine, is described in another information circular of the Bureau of Mines.3 The writer gratefully acknowledges the generous cooperation of the company officials which made this investigation possible, and wishes to thank R. J. Mechin, manager, P. W. Wolf, mill superintendent, and F. G. Kuehl, assistant mill superintendent, for their helpful assistance. Especial thanks are due J. S. Brown, geologist, for supplying information on the characteristics of the ore, and to C. F. Jackson, principal mining engineer, U. S. Bureau of Mines, for helpful suggestions.

Jan 1, 1932

By H. W. St. Clair

Sampling of heterogeneous mixtures of fused metals or solidified melts is subject to errors not met in sampling finely ground ores or granular materials. These errors arise largely because of the segregation of constituent metals that usually takes place during solidification. It is seldom that a random sample of a lot of metal will represent the composition of the entire lot. The problem becomes especially difficult when it is necessary to make accurate analyses for a segregated impurity present in very small amounts. This paper discusses some of the pertinent experimental observations made in selecting a method for sampling melts of aluminum and zinc containing small amounts of iron and silicon as impurities. Although this experimental study dealt only with sampling this specific combination of metals, many aspects of the study apply generally to any mixture of mol ten metals containing minor constituents that segregate rapidly during freezing of the melt.

Jan 1, 1949

By John L. Nieber

This information circular describes a computer program called VARSAT2D, a comprehensive unsaturated fluid flow simulator developed by the U.S. Bureau of Mines. VARSAT2D solves for either a vertical or horizontal, transient or steady-state solution in variably saturated, heterogeneous, anisotropic porous media using the Galerkin finite-element approach. Simplex triangular elements are used. Moisture retention characteristics are described by specifying either the Brooks and Corey, Brutsaert, or Van Genuchten power functions, with hysteresis described using the Maulem independent domain model. Boundary conditions may include any combination of time-varying seepage, pressure along solution domain, boundaries and/or at internal node points, unit hydraulic gradient at the lower boundary, and a uniform source and/or sink. This program should be a welcome addition for mining and environmental hydrologists, researchers, and engineers interested in modeling unsaturated fluid flow.

Jan 1, 1994

By Ronald P. Hollenbeck

The value of mineral production in Alabama increased 1 percent above the record high set in 1965. Alabama ranked second among the States in the production of bauxite, third in the production of masonry cement, native asphalt, and scrap mica, sixth in the production of portland cement, ninth in the production of iron ore, and tenth in the production of lime. The mineral industry of Alabama was dominated by the mining and processing of coal and stone, the manufacturing of cement, and the production of crude petroleum. These industries accounted for 87 percent of the State's total value of mineral production, compared with 85 percent in 1965.

Jan 1, 1967

By Peter D. Lohn

The Bureau of Mines conducted both laboratory and field investigations to study the effectiveness of medium-pressure (up to 30,000 psi) water jets in controlling the generation of airborne respirable dust during the hydraulic fragmentation of coal. Laboratory studies were conducted at the Farmington High Energy Test Site of the Twin Cities Mining Research Center, and field studies were carried out at the Humphrey No. 7 mine, Mount Morris, Pa., in the Pittsburgh coalbed. The water jets were produced by commercially available triplex pumps. The dust samples were collected by midget impinger samplers, and analyzed by electronic and optical counting techniques. Respirable dust concentration for a full-scale production model was projected at below 2 mg/m3, the maximum exposure allowed by the Federal Coal Mine Health and Safety Act of 1969.

Jan 1, 1975

By P. H. Francis

In This report, factors which currently enter into the design, manufacture, and quality assurance of explosion-proof enclosures are reviewed, with special emphasis given to the sealing concepts and sealants/cements, per se, for lenses. The physical and mechanical properties of a number of representative sealants and adhesives are measured, and found to exhibit great variance, with few discernible trends which might afford a firm base on which to establish minimum property standards. Accordingly, acceptance criteria for adhesives and sealants are suggested based on the survivability of an explosion-proof enclosure as a structure rather than upon the minimum mat real properties of its constituents. Procedures or surface preparation of adherends, and for quality assurance, also are proposed.

Jan 1, 1980

By Eldon K. Stanek

The material presented in this chapter is a review of the work done during the period from June 23, 1972 to June 22, 1973 which was reported in detail in the first annual report for Grant No. 60122088 which was submitted on June 29, 1973. This report has appeared in the National Technical Information Service as bulletin number PB230 972/AS. 1.2 ANALYTICAL PREDICTIONS OF INDUCED VOLTAGES AND CURRENTS The basic building block in this analytical work is the development of an equivalent circuit. The equivalent circuit for the cable depends on all of the distributed parameters of the cable, although the series inductance and resistance are of primary importance. The cable resistances are generally available from handbooks or from cable manufacturers. On the other hand, the cable inductances are not usually available from either handbooks or the manufacturer's published data. Thus, it is useful to present the results of the derivation of the inductance matrix and a few intermediate steps.

Jan 1, 1975

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow

"The use of diesel equipment in underground coal mines is controversial because ""whole diesel exhaust"" is regarded as ""a potential occupational carcinogen"" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2, and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols.The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.Air quality data were collected in four underground coal mines using continuous mining methods with diesel haulage equipment. Daily samples were collected at the section intake, haulageway, and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments, including the PDEAS and the micro-orifice, uniform deposit impactor (MOUDI) which sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2, and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters.The concentrations of CO, CO2, NO, NO2, and SO2, were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed using this instrument was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3."

Mar 1, 1992

By F. A. Penning

A number of highly instrumented free fall tests were performed on an arrestment system for a man cage in a vertical shaft. Tests were conducted in the U.S. Bureau of Mines free fall test tower at the Colorado School of Mines. A single tooth safety dog was used to stop on 4x6-in. Keruing (Phillipine mahogany) wet and dry wood guides. The safety dog had a penetration depth of 1 in., an adjustable width from 1-1/2 to 2-1/4 in., and a tooth angle of 80 deg. Twenty-seven free fall tests were performed covering a range in weights from 3-1/2 to 10-1/2 tons, hoisting velocities from 850 to 1350 feet per minute. Average g loads were measured from a low of 0.6 to a high of 3.4. The electronic instrumentation included piezoelectric and seismic mass accelerometers, strain gages on structural and mechanical elements, load cells in the guides, and distance measuring. Computer analysis was used to correlate with experimental measurements used to calculate stress. A statistical analysis gave no indication that the velocity or area affected the wood crushing stress. The instrumentation revealed a chatter occurring during the stop as shown by the accelerometers, strain gages, and load cells. Additional work is required to analyze this newly discovered phenomenon. The chatter imposes loads much higher than the average g load.

Jan 1, 1980

By N. S. Petersen

As part of the Demand Evaluation Program of the Bureau of Mines to determine future needs for minerals, a study was instituted to develop and describe a methodology for approaching the problem of substitution between mineral commodities and between mineral commodities and other materials. The report comprises three sections: A review of general factors relative to substitution, a case study of the effect of substitution on zinc die-casting markets in recent years, and a general methodology for reviewing materials substitution with specific emphasis derived from reviewing substitution in the domestic zinc die-casting markets.

Jan 1, 1971

[ ]

Jan 1, 2011

By Robert L. Lagace

[Suuple Iheorctrccil models are I'M lllolalcd to cltaraclerl/c medium frequency (MF) radio vase pi opaiation in undcrgiounli room arid pillar coal mines fur the purpose of predleiln the most lavolable operating fIegtucncics,md nr,ixunum communic;IIIoil ranges for pottahIe rldu)s with I top antennas. I or conductul IrCC areas, at hree layer propaeaIion IltodcI wit II a Iiallsmissloil IIIIi- lhlllllIIal'u11 lot the plupa!edti ii unlstallt Iris been dcvcloped ;md verified experimentally. 1 lie mode u1 propaCaUetl lakes Ills form of i parallel plane (0,t)) TIM lransnussu)nhne 1% PC of mode with the electric held vertical and the magnetic held hoti/cntal t itliin a planar coal scam in which the tunnels Can he ignored and which 1s hounded above and below hp richer conductivity rock. 1lie model lilt the data best river the 200 io 1000 kH/ frequency hand and exhibits a rc;;lon of optlnrul1l Pelffelntance, with respect Io maxnluiulg radio Communication range, between 300 and 100 klf/. Maximum cunununlcatrorl ranges are sliongls dependent oil the sigiial alleilliatroil sale, ant) Illelclulc on the electrical conductivltles of the coal seam and surrounding ruck. These ranges v;ny tutu about ,,5 Io 100 nleleis Ill a high Iuss scam such as the Ilelllit No. fl to about .100 to 400 meters in a low loss seam such as the Pittsburgh foil portable intrinsically safe radios. The ieslllls die haled on the comparison oftheorc' and experiment for eleven n n. ill sesen coal seams. V OT ate is dice: a conductor such as a power Cable, is present a model has been developed for the coupling of loop antennas to a low loss Coaxial TEM ti;u?smisslon line mode in which the cable acts as the inner conducl,lr and the rock above and below acts as the outer conductor. The electuc and md' nctic Itelds for till` (node are apprlixitllatcly transverse to the cahlC and fall oil expontially with distance in the transverse plane. The principle of reciprocity is used to simplify the analysis. More expelitnental data arc needed to help resolve discrepancies between the theory and the limited data available to date.]

Jan 1, 1980

By Paul L. Michael

This report presents a discussion of perforance parameters for electronic or active hearing protectors that will meet the needs of underground coal miners. This information is incorporated into a proposed set of specifications that can be used to judge the suitability of a particular electronic hearing protector for the coal mine application. Acoustic and electrical tests were performed on a developmental model of an electronic hearing protector built by the U. S. Bureau of Mines. This model showed only a slight reduction in speech intelligibility which was traced to poorly matched components and in particular to the transducers. Tests of alternative components showed the Knowles BL-1671 microphone to be suitable for this application because of its performance and extremely small size. The Roan-well H-143/AIC earphone was found to have a good frequency response but has the disadvantage of being rather bulky which causes a slight degradation of a low frequency attenuation of the hearing protector. A satisfactory installation of these components in a hearing protector muff was demonstrated and tested. Results of tests of several methods of controlling the sound level under the hearing protector muff showed that a simple diode clipper circuit can be used with only a negligible loss in speech intelligibility for normal-hearing listeners. A commercially available active hearing protector, the British-built ACOS A-9000/2 was examined. This hearing protector provides sound level limiting through a saturating amplifier. Preliminary tests have shown that the performance characteristics of this commercial unit meet many of the proposed specifications so further testing and evaluation should be performed to determine its suitability for use 1n underground coal mines. The recommended test of intelligibility for electronic hearing protectors and other communication systems as used in a coal mine setting is the Modified Rhyme Test (MRT) developed by House et al. in 1965. The suitability and method of administering this test are discussed.

Jan 1, 1976

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

Alumina can be recovered from clay , using 30 percent nitric acid for digestion . Calcined clay is crushed and then digested at 325 ° F and 85 psig pressure with less than stoichiometric nitric acid required to form normal aluminum nitrate . In this way , a solution containing both normal aluminum nitrate , Al ( NO3 ) 3 , and basic aluminum nitrate , assumed to be Al ( OH ) ( NO3 ) 2 , is formed , and in which iron is virtually insoluble . The solution is filtered and then concentrated in vacuum evaporators to crystallize normal aluminum nonahydrate . The crystals are washed with 50 percent nitric acid and then decomposed to alumina and nitrogen oxides . The design that has been developed for this process is based on published work . For a plant producing 1,000 tons of alumina a day , the estimated operating cost is $60.69 per ton of alumina , and the estimated fixed capital cost is $ 76 million using a Marshall and Stevens chemical equipment index basis of 240.0 . This process is not competitive under current economic conditions with the production of alumina from bauxite via the Bayer process . For lowering costs , future research should include study of leaching at lower temperatures under atmospheric pressure and alternate aluminum nitrate decomposition methods .

Jan 1, 1964