Search Documents

By David Burgess

Natural gas is a general term applied to the gas obtained from oil or gas wells. It is the most widely used of all gaseous fuels. The principal disadvantage in the use of this and other gaseous fuels is the difficulty encountered in the storage and transportation of large quantities in the gas state. Handling in the liquid state is possible, but reduced temperatures are required since methane (table 1) is the principal component of most natural gases that are used as fuels. Actually, liquid storage has been utilized both here and abroad;3 however, the Cleveland disaster4 has pointed out the need for a critical evaluation of the hazards involved in the storage of this cryogenic fuel. Accordingly, a program was undertaken to obtain basic data that could be used to assess these hazards. In this report, the factors to be considered in an evaluation of the fire and explosion hazards associated with any fuel are each discussed briefly. These factors are then used to assist in the design of experiments for the evaluation of the hazards associated with liquefied natural gas (LNG) relative to those associated with other common fuels. Experiments have been conducted on the vaporization of LNG, the mixing of LNG vapors with air, the effect of temperature and nitrogen dilution on the limits of flammability of methane in air, the burning rates of LNG and other fuels, flame radiation, and extinguishment of fires above liquid pools. Based on the results of these experiments, LNG can be stored safely in suitably designed above-ground tanks surrounded by earthen dikes in much the same manner as gasoline.

Jan 1, 1962

By Douglas F. Scott

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied an 11,980-acre part of the 33,300-acre High Rock Canyon Wilderness Study Area, CA-020-913B, in order to evaluate its identified mineral resources. No mineral resources were identified during this study, and no significant amounts of gold, silver, mercury, gem-grade opal, or placer gold are present. The study area is located in Washoe County, NV, about 53 miles southeast of Cedarville, CA. No mining districts or mineral production are known, and no oil and gas leases are in the area. No current claims are in the area; however, six placer claims were located in 1911 in High Rock Canyon near its confluence with Mahogany Creek.

Jan 1, 1987

By G. K. Derby

The Bureau of Mines investigated methods for removing dragline bucket wire rope terminations with the objective of finding efficient methods that are safer than the method most commonly used at U.S. surface mines, which is to use the explosive impact of a projectile fired from a cannon to remove the rope termination. Removal of a wire rope termination for repair or replacement requires separation of the wedge and socket that lock together to secure the rope end. The Bureau investigated currently used methods and improved upon and tested two safer alternate methods for removing wire rope terminations. A cannon test program was conducted, using 40-and 50-gr primer (detonating) cord, to establish the possible force produced with a 4-in-bore cannon and a 55-lb projectile. Wedge and socket units supplied from cooperating mines were separated under controlled conditions to establish data on separation force requirements. The two alternate methods investigated were use of the force generated by (1) a pendulum ram and by (2) a portable hydraulic pusher. Both methods are capable of providing sufficient force to effect wedge and socket separations on draglines with up to 78-yd3 buckets under normal conditions.

Jan 1, 1984

By Glenn Adkins

This report characterizes pivoting joints in the structures of mining machinery and how the wear on the various components, i.e., pins, lugs, yokes and bushings, may affect the safety of mine personnel where these components are allowed to wear excessively before repair or replacement.

Jan 1, 1979

By Harmon E. Keyes

Many organizations, including the Bureau of Mines, have made intensive studies of the application of leaching methods to relatively small low-grade disseminated deposits of copper ores, containing both oxide and sulphide minerals. One of the principal difficulties has been to obtain a solvent that could be made at a low cost and would effectively dissolve the copper minerals. Another drawback has been the high initial cost of a plant and the refined type of mechanism ordinarily required by standard practice for carrying out the leaching cycle. The Bureau of Mines has attempted to develop a cheap and efficient solvent that would especially meet the requirements of smaller plants. (See Bibliography.) It has been known that dilute ferric sulphate-sulphuric acid solution is an excellent solvent for most copper minerals, such as chalcocite, bornite, and oxidized forms, but not for chalcopyrite and certain silicates. A method of producing this solution from sulphurous products and waste liquors was developed by the bureau and tried successfully on a test-plant scale at the Southwest Experiment Station in cooperation with the department of mining and metallurgy, University of Arizona, Tucson, Ariz. However, this work did not involve the actual leaching of ores with the solutions thus produced or the cyclic use of the iron solutions in the regenerator cell. Except for certain laboratory tests, in which known impurities were added, no data were available to show the effect on regeneration if accumulations of impurities were built up in the leaching circuit.

Jan 1, 1930

By William H. Pomroy

This report describes Bureau of Mines research that led to the design, prototype fabrication, and successful proof-of-concept testing of an improved stench fire-warning system for underground noncoal mines. Stench systems are the most widely used means of warning driers in underground noncoal mines of fires or other emergencies. A stench system alerts miners that an emergency condition exists by injecting an odorant into the mine air. Although stench warning systems have been used successfully for over 60 yr, present systems suffer several serious shortcomings, including odorant toxicity, unreliability of warnings, widely varying stench concentrations, and others. In 1980, the Bureau began a research program to upgrade the stench warning system. The resultant system overcomes the deficiencies of existing systems by substituting tetrahydrothiophene for the commonly used ethyl mercaptan stench odorant, and through the use of a specially designed stench injector. The improved injector reliably meters stench fluid into either ventilation-air or compressed-air streams at a precisely controlled rate. Prototype hardware has been fabricated and proof-of-concept tested under bath laboratory and in-mine conditions.

Jan 1, 1985

By John Ward Smith

Detailed oil yield, lithologic, and mineral distribution data are presented for core and drill-cutting samples from the Western Oil Shale Corp. Project Utah EX-1 Corehole (WOSCO EX-I), drilled to sample a deeply buried oil-shale sequence in the Green River Formation of Utah's Uinta Basin. Drilling of this corehole was part of the evaluation of this site for possible oil-shale development by nuclear explosion. Sections sufficiently thick for nuclear development average 15 gallons per ton or less and consist predominantly of low-grade shales. Some properties of low-grade shales may be advantageous to a nuclear experiment by facilitating breakage, fracture development, and in situ retorting. The formation correlates precisely with the well-studied oil shales 25 miles east near the Colorado border. A 235-foot mineralized section containing nahcolite, shortite, and searlesite whose bottom lies 300 feet above the Mahogany zone is described.

Jan 1, 1972

This report summarizes the results of several field tests conducted by Collins for the Bureau of Mines under contract S0122076 and contract H0232056. The field projects represent a part of Collins continuing effort on a broad study of coal mine communications. These experiments analyze the propagation characteristics of radio signals in a working coal mine environment. The intent of the program is to provide basic propagation loss characteristics by which we may evaluate various approaches to an integrated mine communications system. The goal of such a system is to satisfy both operational and emergency communications needs in the mine.

Jan 1, 1974

By Paul C. Hyndman

Three properties in the Tuolumne River RARE II area, the Eagle Bluff Mine (lode) and the Indian Creek Bar and Bossy Bar Prospects (placer), have identified subeconomic gold resources (table 1). Nineteen other properties have potential for gold resources. Adjacent to the study area, five properties have identified mineral resources, and nine others have potential for resources. Properties having high-grade zones (shoots), but licking enough tonnage to be classified as resources, are listed in table 2. Gold, in lode and placer deposits, is the principal mineral commodity in the Toluene River study area. Ten properties within the RARE II boundary have gold-rich zones or shoots; they range in size from 12 to 2,500 tons and in average grade from 0.09 to 0.97 oz gold per ton.

Jan 1, 1983

By Lynn Alcorn, Jeffrey Shawn Peterson

Data collected by the Mine Safety and Health Administration (MSHA) has shown that roof bolting machine (RBM) operators are the second most likely type of underground mining machine operator to be are over exposed to noise, per the MSHA Permissible Exposure Limit. In response to this, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has initiated a project to develop engineering noise controls for roof bolting machines. Key to this research is an evaluation of the duty cycle of a typical roof bolting machine operation and this paper presents the results of such an exercise for data collected at two cooperating coalmines. The evaluation entails a time motion study of an operators' shift, logging each activity for time (e.g., tramming the machine, drilling holes, installing the roof bolt, etc.) and the noise levels associated with each task with a Larson Davis Spark 705+ dosimeter. NIOSH post processed the data to determine which tasks the operator devotes the most time to and the noise dosage accumulated during those tasks. These results provide insight into which portion of the operators' duty cycle is the most prominent contributor to noise exposure and thus, where research activities for the development of engineering noise controls should be focused. It was determined that the task of drilling holes is the most significant source of the operators' noise exposure and project research has focused on engineering noise controls to reduce the noise emissions generated during the drilling portion of the machine duty cycle.

By Laurence A. Dahners

As part of the strategic minerals program, the Bureau of Mines conducted a diamond-drilling project on three barite properties in eastern Tennessee and western North Carolina during the summer and fall of 1944. These properties, the Moccasin Gap prospect and the Krebs property in Cocke County, Tenn., and the Sandy Bottom mine of the Stackhouse group in Madison County, N. C. (fig. 1), are known to have produced some barite. The Bureau of' Mines project was planned to prospect for extensions of the ore bodies. A total of 3,169 feet of diamond drilling was done in 15 holes on the three properties. Tabulations of sample analyses and drill-hole logs are presented in this report. Two other mines of interest in the area are the McCoy and the Williams in Cocke County, Tenn. The Williams adjoins the Krebs. No drilling was done by the bureau in either of these properties.

Jan 1, 1949

By Paul J. Remington

The field data gathered as part of the measurements described in Volumes I and II were re-analyzed in the low frequency regime (.1 Hz to 1 Hz) where motion sickness normally occurs. These data were compared co the international standard ?ISO 2631 Addendum 2: Evaluation of exposure to whole body z-axis vertical vibration in the frequency range 0.1 to 1.0 Hz." For both underground mining machines and surface mining machines the results showed that one would not expect motion sickness to .be a severe problem. New field data were gathered on the vibration reduction performance of various seat designs found on surface coal mining machines. The vibration during normal operation was measured on the seat using the standard seat pad accelerometer package described in the previous two volumes and simultaneously on the floor of the machine at the base of the seat. Preliminary indications are that the so-called high performance seats used for operator vibration reduction do not offer significant improvement over conventional seats.

Jan 1, 1984

By J. S. Dunning

One Federal Bureau of Mines research goal, to minimize requirements for domestically scarce mineral commodities through conservation and substitution, can be accomplished by utilizing more abundant elements such as iron, molybdenum, and titanium. An example of this research is the study of precipitation-hardening, iron-base alloys containing molybdenum and titanium, as substitutes for the high-tonnage stainless steels that are high in imported nickel and chromium. The precipitation hardened iron-base alloys are strengthened by a dispersion of the ternary Laves phase, Fe2 (Mo, Ti). Aluminum and chromium additions changed the solid solubility limits of molybdenum and titanium in a-iron and affected the composition of precipitating phases. A baseline composition of Fe-7Mo-2Ti was selected to study the effects of aluminum and chromium additions on the precipitation-hardening mechanism and microstructure and was also used in studies of mechanical properties and oxidation resistance. The study yielded workable, precipitation-hardening alloys, with elevated temperature strengths equivalent to or superior to types 304 and 316 stainless steels. Chromium and aluminum additions in combination were more effective in providing oxidation resistance than either addition was alone.

Jan 1, 1980

By V. R. Miller

The Bureau of Mines developed and evaluated a detecting and sorting device to separate the copper-bearing portion from the barren portion of Michigan native copper ore in the minus 4- plus 1-inch size range. Small-scale sorting tests were also conducted on minus 1- plus 1/2-inch material from the Centennial No. 6 mine, using a previously developed system that was modified to increase sensitivity. Results showed that, with the added sensitivity, 85 to 90 pct of the copper in the minus 1- plus 1/2-inch material could be recovered in about 50 to 60 pct of the fraction. Sorting tests on minus 4- plus 2-inch and minus 2- plus 1-inch fractions from the Centennial mine were conducted with the large sorting system. Results showed that 86 to 93 pct of the copper was recovered in 43 to 64 wt-pct of the sorted fractions. Combining of concentrates from the two fractions resulted in a recovery of 90 pct of the Popper in 55 pct of the weight. The composite concentrate contained 2.40 pct copper, and the tailing analyzed 0.33 pct Cu; the head sample assayed 1.46 pct Cu.

Jan 1, 1978

By R. V. Ramani

This volume is the first of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume II: Dragline Model, Volume III: Mine Coordinate Generator System, and Volume IV: User's Manual for OPMHS/2. This report deals with the development of a geological model for surface mine planning. The most common orebody modeling techniques are described. A brief review of geostatistical theory and concepts is presented. A geostatistical option for orebody modeling is developed and validated. Computer programs and sample outputs are appended.

Jan 1, 1985

By Robert Stefanko

A series of workshops were conducted -with invited participants from the coal mining industry to identify the most pressing research and development needs of the industry. Six workshops were held on the following subjects; Research Priorities for Mining-Oriented Universities, R&D Needs-for Surface Coal Mining, R&D Needs for Deep Coal Mining, R&D Needs for Anthracite Coal Mining, R&D Needs for Coal Mine Health and Safety, and R&D Needs far Environmental Control in Coal Mining.

Jan 1, 1975

By Gary E. Sherman

Preliminary economic mining feasibility studies were conducted by the Bureau of Mines to estimate mining costs in the Juneau gold belt area of the Juneau Mining District, southeastern Alaska. Investigations were conducted on the economics of two mineral deposit types: (1.) Berners Bay vein gold deposits, and (2.) stockwork gold deposits containing gold, silver, and lead. Cost estimates were developed using the Bureau of Mines Cost Estimating System (CES). Discounted cash flow return on investment (DeFROI) was calculated using the Bureau's MINSIM computer program. Underground mining of a Berners Bay vein gold deposit was found to be economic (15 pct DCFROI) at a recoverable metal value of $353.67/mt for a 100 mtpd shrinkage stoping mine with a 10 yr mine life, $324.76/mt for a 20 yr mine life, $138.63/mt for a 500 mtpd longhole stoping mine with a 10 yr mine 1 ffe, and $127.50/mt for a 20 yr mine life. Block caving mining of a large stockwork gold deposit was found to be economic at a recoverable metal value of $15.28/mt for a 18,000 mtpd mine with a 20 yr mine life.

Jan 1, 2011

By W. L. Cooley

The report provides a detailed analysis of 23 electrical accident countermeasures contemplated for use in the metal/non-metal mining industry. The costs and potential benefits of implementing groups of these countermeasures are estimated, and methods arc outlined by which the operator ran choose countermeasures in an effective manner. The analysis is based largely on an extensive electrical accident event tree which is developed in detail. For those countermeasures which are not currently technically feasible, several prototype devices were developed to help speed development. These included a trolley arc eliminator and a safer mine electricians multimeter.

Jan 1, 1982

By Terry R. Neumann

A mineral survey of the 23,760-acre Abert Rim Wilderness Study Area (OR-1-101) was conducted by the U.S. Bureau of Mines in 1986 at the request of the Bureau of land Management in order to evaluate its identified mineral resources. The study area is located in south-central Oregon, 26 mi north-northeast of Lakeview, OR. Federal and Lake County mining records indicate no mining claims, geothermal leases, or oil and gas leases within the study area as of January 1, 1987. No economic concentrations of minerals were found in the study area. The Wilderness Study Area is dominated by Abert Rim, a north-trending Basin and Range fault scarp that parallels the study area's western boundary. Exposed on the scarp is an approximately 2,000-ft-thick volcanic sequence consisting of Oligocene-Miocene basalts, tuffs, and tuffaceous sedimentary rocks.

Jan 1, 1987

By G. St. J. Perrott, G. W. Jones

"In the course of its investigations pertaining to the promotion of safety the Bureau of Mines is actively engaged in investigating all promising materials that may be of value in rendering methane or other combustible gases, vapors, or solids less inflammable.Added substances are of value if such additions narrow the limits of inflammability, raise the ignition temperature, lower the speed of propagation of flame, or reduce the maximum pressure developed. Of major importance is the effect of added materials on the limits of inflammability, because methane is the chief combustible s liberated in mines, considerable work has been done with extinguishing agents on methane flames. For obvious reasons, a substance to be of value for the extinction flames should be a gas, or a liquid having a sufficient vapor pressure to give concentrations of the vapor in sufficient amounts to extinguish the flames or markedly narrow the limits of inflammability. The substance should be nontoxic, cheap, and noncorrosive and must be incombustible. Solids, such as rock dust, are undesirable and of little value for combustible gases because they soon settle out of the atmosphere, and their flame- extinguishing value is thereby lost. There are at present only a few gases and vapors-for example, nitrogen, carbon dioxide, and carbon tetrachloride-which meet these requirements.The extinction of methane flames by nitrogen, carbon dioxide, and argon has been reported by Coward and Hartwell 4; the extinction by water vapor by Coward and Gleadell 5, and the extinction by helium and carbon tetrachloride by Coward and Jones 6."

Oct 1, 1930