Search Documents

By Donald O. Capstick

The U.S. Bureau of Mines conducted an inventory of the prospects and mineral resources in the Scodies RARE II area (No. 5212) in 1982. No mineral production is recorded from the area, and no mines are being developed. The Scodies RARE II area is comprised primarily of light colored granodiorite with minor inclusions of mafic granitic rocks. Late stage differentiates of magmas resulted in quartz veins and pods. Metasedimentary rocks which have been mineralized in some parts of the Sierra Nevada were not observed within the study area during this investigation but small inclusions have been reported.

Jan 1, 1983

By W. G. Payne, A. C. Richardson, B. L. Gandrud

"INTRODUCTION The Connellsville mine of the Yolande Coal & Coke Co. is in the southwestern part of Jefferson County, Ala., about 30 miles southwest of Birmingham. The mine is on the Blue Creek bed, which is about 6 feet thick and dips at a angle of 18º. The bed is worked by the room-and-pillar method and is mined by both machine and hand methods. The Blue Creek bed at this point yields a high ash, low-volatile coal with excellent coking properties. Because of its exceptionally low volatile content and high coking strength, this coal is excellent for blending with Alabama coals of higher volatile content and weaker coking properties to form blends suitable for production of metallurgical coke.A sample of washed coal taken during this investigation gave the following analysis on an as received"" basis: Moisture, 8.3 per cent; volatile matter-, 20.2 per cent; ash, 8.0 per cent; fixed carbon, 63.5 per cent. The high ash content of this coal limits the quantity which can be utilized when low-ash coke is required. In the Birmingham district it is usually difficult to sell as coking coal a product that contains more than 8.0 per cent ash. To produce a. coal with this ash content at Connellsville presents a somewhat difficult washing problem. This paper gives the results of an investigation that was conducted by the Southern Experiment Station of the U. S. Bureau of Mines in cooperation with the University of Alabama and the Yolane Coal & Coke Co. for the purpose of determining the washing characteristics of the coal and the possibility of reducing its ash content on coal-washing tables.The practice at the Connellsville washery at the time of beginning this investigation was to crush the run-of-mine coal to pass a 1 1/2-inch round-hole screen and to treat the satire output on two primary, 3-compartment jigs. A. middling product was recovered from the primary jigs which was re-treated on a single-compartment rougher jig. This system yields a product of acceptable ash content, but the yield is low and the loss of good coal in the refuse is high."

Feb 1, 1933

By Virgil Marple

In the summer of 1979 the University of Minnesota Mobile Laboratory (UMML), designed for the analysis of airborne particles and gases was used to study fugitive dust from an open pit coal mine. The analysis consisted of determining the particle size distribution and concentration of dust from various mining operations, such as blasting, draglines, loading, roadways and bottom scrapers. For some operations the particles size distribution and concentrations were determined at varying distrances. Details of the dust concentration within the plumes as the plume passed the UMML were measured with an optical particle counter. For line sources, such as roadways this enabled the calculation of the particle flux at the sampling location. In addition to the standard instruments associated with the UMML, the applicability of some new instruments were investigated. These included a uniform deposit cascade impactor and a flux meter. Finally, a technique in identifying plume origins which utilized elemental X-ray flourescence analysis of filter samples was shown to be effective.

Jan 1, 1980

By J. L. Holman

The Bureau of Mines, at its Rolla Metallurgy Research Center, has devised methods for separating and reusing the major portion of waste plastics discarded in urban and industrial refuse. Waste plastic concentrates from a local collection drive, recycling center collections, urban refuse pilot plants, and the secondary metals industry were separated into three major thermoplastic families--polyolefins, styrenes, and vinyls--based on differences in density using a Bureau-designed sink-float-elutriation hydraulic separator. Other separation methods and systems such as air classification, jigging, liquid media, screening, and electrostatics were studied. Vinyl plastics contain up to 50 percent HC1. It was found that over 90 percent of the HC1 in vinyls can be recovered as usable hydrochloric acid by pyrolysis at 350° C. The remaining pyrolysis products which had heats of combustion in excess of 12,000 Btu/lb, could become valuable as a future source of energy. A characterization study conducted on eight chopped wire insulation wastes from secondary copper and aluminum processors showed that most wastes contained 2 to 7 percent residual metal and large percentages of vinyl. The residual metal content of some of these wastes was lowered to 0.1 percent and the vinyl portion segregated using various separation techniques. The research also suggests ways in which reclaimed thermoplastics may be fabricated into useful products.

Jan 1, 1974

By R. Emmett Hughlett

The Bureau of Mines has developed a statistical approach to the laboratory evaluation of response bias and precision in gas detectors. The techniques described employ a computerized analysis and a new method of data presentation called composite graphing. The underlying theory, its practical application to the data, and the experimental equipment and procedure are described.

Jan 1, 1982

By Gerrit V. R. Goodman

In This Chapter [Design and operation of machine-mounted scrubbers Dust control with scrubbers and blowing ventilation Dust control with scrubbers and exhaust ventilation Dust control with exhaust ventilation and no scrubber Dust control methods common to all continuous miner sections Dust control for roof bolters] This chapter explains how to control dust at continuous miner sections in coal mines where the main dust sources are continuous miners and roof bolters. In relation to dust, there are three categories of continuous miner faces depending on the type of ventilation and whether or not a machine-mounted dust scrubber is used. These are— 1. Mining machines with dust scrubbers used with blowing face ventilation 2. Mining machines with dust scrubbers used with exhaust face ventilation 3. Mining machines without scrubbers used with exhaust face ventilation The approach to dust control is somewhat different in all three of these. However, there are many dust control features (such as the need to provide adequate airflow) common to all continuous miner sections. For workers at roof bolter faces, there are two dust sources: 1. Dust from the continuous miner when it is upwind. 2. A malfunctioning dust collector on the bolter, which allows dust to escape DESIGN AND OPERATION OF MACHINE-MOUNTED SCRUBBERS [Almost all new continuous miners are equipped with scrubbers. When the dust is excessive, it is possible that the scrubber needs some maintenance.]

Jan 6, 2003

By T. C. Green

A two-phase program evaluated commercial proximity warning devices and then served to design and develop an automatic electrostatic field strength measurement device with improved performance. The Phase I program consisted of test and evaluation of three commercial proximity warning devices, all of which operate on the principle of electrostatic field intensity measurement for determining proximity to high voltage power lines. Performance testing of these devices utilized full-scale cranes and power line systems and a scale model facility. The evaluation results were reported in the Phase I report entitled "Evaluation of Proximity Warning Devices" dated 22 February 1980. Under the Phase II program, a microproressor-based data acquisition system was designed and developed to collect and measure field strength at distributed points around the crane boom. This unit (referred to as the Distributed Sensor AC Electrometer) measures the field strength about a crane boom using 17 distributed sensors. Keyboard control is provided for the equipment operator. Measured field strength values are displayed on a line printer and recorded on magnetic tape. Laboratory testing of this unit demonstrated performance characteristics and field strength measurement accuracy within the design goals. A Phase III measurements program is proposed using the AC Electrometer to map the field strength contours about power line configurations.

Jan 1, 1981

By Harvey L. Pastan

The purpose of the investigation and analysis described in this report is to assess the data flow requirements that are required for remote supervisory control of a continuous mining system. Since these control concepts as applied to continuous underground mining are still in a formative stage at the present time during the first half of 1975, assumptions had to be made based upon engineering judgment as to what embodiment of mining machinery and control methodology seemed most feasible for achieving such a system. Based upon these assumptions and estimates of the control system's accuracy and response requirements, it was then possible to estimate the communication requirements for the assumed system configuration. 2. Approach The team members responsible for this study visited numerous coal mines to observe room and pillar mining operations in both high and low coal. The objective was to observe the methods of operating a variety of continuous mining machinery and haulage equipment with a view toward defining the problems to be overcome in the application of automation to the coal extraction process. Descriptive information concerning the mining equipment was obtained through contacts with the manufacturers. Conferences with Bureau of Mines personnel, equipment manufacturers and developers, and mine operators were held to explore the current thinking and developments being pursued toward automation and increasing both production and productivity.

Jan 1, 1975

By Robert B. Worthington

This investigation was undertaken to develop a more efficient copper smelting practice that would help meet the increasingly stringent antipollution standards. Continuous smelting to copper and a 0.8-to 5-percent copper slag using pure oxygen has been demonstrated for several hours at a time in a unique double furnace, which was devised to overcome the heat losses inherent in a laboratory furnace. The use of pure oxygen to effect the smelting and conversion of copper sulfide concentrate in a single unit to produce blister copper and a very high S02 concentration provides a much reduced gas volume for more economical and thorough sulfur recovery. Although the process was successfully demonstrated for several hours at a time, extended test work using longer runs will be required to balance the system and to obtain test data for adequately demonstrating its technical feasibility.

Jan 1, 1973

By S. S. Gross

A program was conducted to determine whether sufficient quantities of the flame retardant, ammonium phosphate, could be incorporated in a water-based foam solution to prevent or delay reignition (burnback) without. significant degradation of foam properties. Up to 20% of mono and diammonium phosphate was added .to d high expansion foam solution. This mixture was applied as a high expansion foam to burning wood and coal samples. The effect of this mixture on burnback was laboratory tested by placing the wood or coal sample in front of a radiant panel. It was found that diammonium phosphate levels of 20% by weight prevented reignition without degrading foam properties. A field test was then conducted using a 20%, diammonium phosphate mixture and a control with no phosphate on a wood crib fire. The experimental foam did extinguish the crib fire faster than the control as evidenced by the smoke from the crib. However neither crib reignited.

Jan 1, 1982

By G. A. Wancheck

Shear tests were performed on several prepared samples of granular and powdery bulk materials to investigate the following parameters: Particle size and distribution, particle movement, moisture content, consolidation of material, bulk density, void ratio, porosity, volume change, and strain rate. A series of shear tests was performed with weight-percent-ratios of minus 0.185-inch tertiary sand and 1-1/2-by l/2-inch tertiary gravel mixtures, and weight-percent-ratios of minus 200-mesh limestone (rock dust) and minus 200-mesh bituminous float coal dust. A comparison was made for shear test results obtained with rectangular and circular shear cells utilizing the large and small direct shear testers. Specifically, the shear results obtained include the angle of internal friction or shear strength of the tested material under known consolidating pressures, and the kinematic angle of friction or coefficient of friction between the interface of a bulk material and a sample wall material. The experimental procedure, tests, and results are given for each parameter investigated.

Jan 1, 1973

By Donald P. Tuchman, Robert P. Vinson, Jon C. Volkwein

Research by the National Institute for Occupational Safety and Health (NIOSH) has pursued quartz analysis for the specialized ?lter assemblies of a new worker-wearable personal dust monitor (PDM). The PDM is a real-time instrument utilizing a tapered element oscillating microbalance (TEOM®). Standard ?berglass TEOM ?lters cannot accommodate the desired P-7 infrared analytical method used by the Mine Safety and Health Administration (MSHA). Novel ?lter materials were tested with the objective of demonstrating this type of analysis. Low temperature ashing and spectrometric examination were employed, revealing that nylon ?ber candidate ?lters left minimal residual ash and produced no signi?cant spectral interference. Avoiding titanium dioxide in all ?lter materials proved to be a key requirement. Fine quartz particulates were collected on prototype ?lters in a Marple chamber, either open-faced or through PDMs during test runs. The ?lters were then subjected to MSHA P-7 analysis and the spectrometrically based analytical results for quartz mass were compared to reference measurements. Also, PDM instrumental mass readings were compared to ?lter gravimetric measurements. Results suggest that the P-7 method is adaptable to variations in ?lter materials and that quartz dust analysis by the P-7 method when utilizing the new ashable PDM ?lters can have accuracy and precision within 10% and 4%, respectively. This is within the declared 13% accuracy and 7–10% precision of the P-7 method itself. Instrument mass readings had modest positive bias but met NIOSH accuracy criteria. Continued work with specialized PDM ?lters is merited, as they are a new type of TEOM sample amenable to ashing analysis of particulates.

Cutter roof failure, a ground control problem that frequently results in massive roof failure, is common in coal mines of the Northern Appala-chian Coal Basin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure to gain a basis from which to predict and prevent its occurrence, and to support such roof when failure occurs or is imminent. Research conducted at the Greenwich Collieries North and South Mines, in central Pennsylvania revealed a correlation between the presence of clastic dikes and formation of cutter roof failure. The research con-sisted of in-mine mapping of geologic and deformational features, rock pressure monitoring, core recovery and evaluation, and in situ stress measurement. It was found that roof failure increased in areas where the occurrence of clastic dikes was most frequent, especially where two or more clastic dikes intersect. Staggering of crosscuts prevented the extension of cutters and deterred the occurrence of large falls extending over several break-throughs. In addition, trusses and cribbing were effective in stabilizing clastic dikes and inhibiting the development of cutter roof failure when employed immediately or shortly after mining.

Jan 1, 1987

By Mark S. Sanders

This report presents recommended visibility requirements for continuous miner, shuttle car and scoop operations and details the methodology used to generate them. A task analytic approach was used to define information requirements and visual features which served as sources of information. Information requirements were prioritized and the location of visual features determined. From this analysis, visual attention locations, containing one or more important visual features, were identified. A total of 71 locations-were identified for continuous miners, 54 for shuttle-cars and 54 for scoops. A procedure was developed for assessing whether operators in existing machines could be expected to see the visual attention locations. The procedure makes use of a Human Eye Reference Measurement Instrument (HERMI) designed for this project and an outside-in photographic procedure for documenting compliance with the recommendations. A sample of continuous miners, shuttle cars, and scoops were used to test the procedure. Results are presented in the report.

Jan 1, 1981

By Robert M. Doerr

The research objective was to determine the effect of vanadium alloy additions on the oxidation behavior of cobalt-nickel Alloys. Eighteen alloys were reacted with 0 2 at 0.5 arm and 1,351°, 1,389°, and 1,429° K. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with V additions of 0, 0.9, and 2.7 wt pct. Large early deviations from, or changes in, the parabolic rate constant were encountered, but the reaction rate in most cases declined approximately in accordance with the parabolic rate law. Relatively, the vanadium degraded the oxidation resistance most at the highest nickel contents. In some cases, melting of the oxide was inferred from microscopic evidence and X-ray diffraction measurements disclosed the presence of low-melting vanadates.

Jan 1, 1970

By F. N. Kissell, C. D. Litton

Abstract-This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

By Edward D. Thimons

The Bureau of Mines developed a stopping design that allows the stopping to be blown down by strong blast forces without incurring any permanent damage. Trials with the new stopping, dubbed the quick-fix blowout stopping, have been conducted in the Bureau's Safety Research Coal Mine at Bruceton, Pa., and in two New Mexico uranium mines. Results have been favorable in all cases. Compared with conventional brattice stoppings or wood bulkheads, the quick-fix blowout stopping is easier and less time consuming to install, is easier to maintain, and in most cases is just as efficient an air barrier. There is same indication that the shape of the stopping makes it more resistant to blast fore s than the fabric stoppings now in use.

Jan 1, 1976

By R. W. Barnes

This circular presents results of a survey conducted by the Bureau of Mines to ascertain the extent to which dust-control practices are employed in the coal-mining industry. This survey was initiated because of increasing realization of the possible harmful effects of the inhalation of dust upon the health of coal-mine workers and the advent, during recent years, of new types of mining machinery and new mining methods that may have a direct effect upon the extent of exposure to airborne dust experienced by persons mining coal. Anthracite Mines The survey covered 169 anthracite mines that were operating from November 1, 1953, to July 1, 1954. It showed that large mines employing more than 100 men were doing most to control dust produced during mining.

Jan 1, 1956

By L. A. Neumeier

The Bureau of Mines evaluated the properties of zinc alloys containing 25 to 40 wt pet Al and 0 to 0.7 pet Mg. Microstructures, hardness, and tensile properties were evaluated for material as extruded at 285° C, solution treated at 300° to 400° C, and subsequently aged at 100° to 200° C. The alloys without magnesium are characterized by low hardness and strength with high tensile elongation and reduction in area. It was verified that magnesium effectively retards the Zn-Al eutectoid transformation below 275° C and markedly increases hardness and strength with decreases in ductility. Solution treating at 350° C results in large grain sizes and gross embrittlement. Subsequent aging of the Zn-Al-Mg alloys at 200° C restores ductility substantially and stabilizes the structures, but strengths are considerably reduced. Combined strength and ductility properties are better for the as-extruded condition than for any heat-treated condition. There is usually little advantage in overall tensile properties from increasing magnesium above 0.1 pct.

Jan 1, 1971

By Jr. Gabler

Methods for the direct spectrochemical determination of impurities at the parts-per-million level in tungsten metal and oxide are presented. Several published procedures were investigated and numerous modifications were made in establishing procedures with improved precision and extended lower levels of determinability. Details of standards preparation are presented, experimental work is described, and three preferred methods are described in detail. A germanium carrier-distillation procedure is applicable to the determination of 13 elements in tungsten powder; a silver chloride carrier-distillation procedure provides for the determination of 24 elements in tungstic oxide, and a sustaining ac arc method is applicable to 26 elements in tungstic oxide. The choice of methods to be used depends upon sample form, elements and concentrations to be determined, and the precision and accuracy required. The investigations reported here were undertaken to develop direct spec-trochemical methods with increased accuracy and precision to determine impurities in high-purity tungsten and tungstic oxide, to define the lower concentration levels of detectability and measurement for the common impurities in tungsten by direct spectrographic means, and to present the details of the developed or modified methods that have proved applicable.

Jan 1, 1965