Search Documents

By H. F. Yancey

About 65 percent of the more than 400 million tons of coal produced annually in the United States is mechanically cleaned to remove the inorganic impurities before being sent to market. The impurities, principally shale and clay with some pyrite, average about 20 percent of the raw coal treated. Nearly 95 percent of the tonnage is treated by wet processes, in which water, suspensions of solids in water, or occasionally calcium chloride solutions are employed. Difference in density of coal and impurity is the basis of these processes. Of major importance in the separation is the competency of the impurities, that is, the resistance of the impurities to size disintegration in water. In general, the impurities are more resistant in geologically older coals or those in effect made older by metamorphism. If the impurities suffer reduction in particle size when immersed in water, the separation of organic from inorganic material becomes more difficult, Recently the Scientific Department of the National Goal Board (Great Britain) undertook fundamental research into the interaction of shale and water and also developed an empirical method of assessing shale breakdown or disintegration. 6

Jan 1, 1962

By Paul R. Thomas

The Bureau of Mines evaluated the impact of the depletion allowance upon the economic availability of copper from domestic deposits. The potential long-run percentage depletion deduction, cumulated over the life of the properties, was estimated at approximately $2.5 billion for producing properties and up to $11.7 billion for nonproducers. The income transfer, in the form of higher Federal income tax payments if the allowance were repealed, was estimated at $1.5 billion for producing properties and up to $8 billion for nonproducers. The percentage depletion allowance, through its role in determining Federal income tax liability, was found to be very significant in affecting profitability. Repeal of the allowance could result in major domestic copper availability reductions at all price levels, now and in the future, as a result of reduced profit margins for current producers, and postponement of development decisions for nonproducers. It was demonstrated that a 50-percent reduction in the percentage depletion rate applicable to copper would also result in a significant decrease in profitability for nonproducing properties. For producing properties, the percentage depletion rate on copper was shown to be less significant than the income limitation that is placed upon the total amount of the depletion deduction. Repeal of the minimum Federal tax provision was shown to be significant in enhancing profitability for both producing and nonproducing deposits. The report concludes that the percentage depletion allowance operates as an important method of capital recovery and production incentive.

Jan 1, 1982

By Frank B. Fulkerson

A study was made of scrap iron and steel in the South Central States in order to determine trends in processing, shipment, and consumption if this important commodity. These data were derived in part from statistical sources and in part by visits to scrap yards and steel mills. Trends in the industry were reviewed. Dealers in 1963 supplied 1.8 million tons of iron and steel scrap to steel mills and foundries in the south-central area, compared with 2.1 mill ion tons in 1955. Most of the scrap was processed and shipped within 200 to 300 miles of consuming centers. Exports provide a principal outlet for dealers along the gulf coast. Most of the scrap that fills these orders is loaded onto freight cars at yards in Texas and Louisiana and is shipped to ports for direct transfer from railroad car to ship. The tonnage exported varies greatly from year to year. The largest scrap operations are in or near large cities which are heavy scrap generating areas, steel mill sites, or port cities for export of scrap. A tentative analysis indicates that the short-run supply of prepared scrap is inelastic to price changes; therefore, buyers probably are in a strong bargaining position at times of declining demand. One technological development in the iron and steel scrap industry is the use of large presses which can take complete automobiles with frames, wheels, springs, and other heavy parts still intact and reduce them to bundles. At Houston, Tex., and Kansas City, Mo., shredding plants are in operation that reduce car bodies and other light scrap into flat pieces 4 to 6 inches in size.

Jan 1, 1966

By Robert D. Perry

This report describes methods of reclaiming abandoned or inactive tailings ponds and dams. The investigated sites were selected tailings deposits adjacent to metal mines in the southwestern United States and the Pacific Northwest. The basic data developed for each site consisted of the following: a review of existing literature: a site visit that included sampling of the tailings and surrounding materials; laboratory and engineering studies; and development of reclamation plans. Laboratory tests determined the gold and silver content of each tailings deposit and the chemistry of the tailings and surrounding materials. Reclamation plans that include approximate costs were developed for five tailings deposit sites. These ranged in size from 52,000 to 103,000,000 tons. Our conclusions on the remining potential of each site are based on the tailings assay and other technical data. This study concludes that remining as a reclamation tool is feasible at certain sites. Included in this report is a remining program as part of the overall reclamation plan for two sites. Our preliminary results indicate that remining as a reclamation tool is feasible for only one of them.

Jan 1, 1981

By Stephen C. Tadolini, Thomas M. Barczak, Peter (Yunqing) Zhang

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear “abutment” moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

By M. E. Hawkins

This Bureau of Mines report provides information on all of the 329 proved salt domes in the Gulf Coastal States and offshore area of the United States. It includes specific data related to location, depth to the cap rock and to the salt, storage facilities for LPG, and production of salt, sulfur, petroleum, and rock related to or associated with the dome structure in the subject area. Also included is a brief history of the salt, sulfur, and petroleum industries as related to the salt domes. Gulf Coast salt domes were the scene of the first discovery of a large deposit of rock salt in North America, the birthplace of the Frasch sulfur industry, and the location of the first large oil gushers that ushered in the modern liquid fuel age.

Jan 1, 1966

By J. M. Goris

The U.S. Bureau of Mines is conducting research on cable bolt ground supports to assess their material and support properties, to provide design criteria for using cable bolt supports as roof control systems under various types of underground mining conditions, and to develop a mathematical model of cable bolt support systems. Part 1 described laboratory studies of the support properties of conventional steel cable bolts. Part 2 describes the strength characteristics of conventional cables with steel buttons, single and double birdcage cables, and epoxy-coated cables.

Jan 1, 1991

By M. E. Hawkins

This Bureau of Mines report provides information on all of the 329 proved salt domes in the Gulf Coastal States and offshore area of the United States. It includes specific data related to location, depth to the cap rock and to the salt, storage facilities for LPG, and production of salt, sulfur, petroleum, and rock related to or associated with the dome structure in the subject area. Also included is a brief history of the salt, sulfur, and petroleum industries as related to the salt domes. Gulf Coast salt domes were the scene of the first discovery of a large deposit of rock salt in North America, the birthplace of the Frasch sulfur industry, and the location of the first large oil gushers that ushered in the modern liquid fuel age.

Jan 1, 1966

By W. L. Heidenreich

This report describes the methods and results of field investigations conducted by the Bureau of Mines between December 1956 and December 1957 on seven deposits of nickel-cobalt-iron-bearing laterite and weathered serpentine near the west coast of Puerto Rico east and south of Mayaguez. These deposits were named, for purposes of identification, Guanajibo, Punta Guanajibo, Las Mesas, north and south deposits of the Rosario Southeast group, and the west and east deposits of the Maricao Southwest group. In addition, the lower 17 miles of the Guanajibo River Valley was tested at widely spaced intervals for possible concentrations of magnetite and chromite in the alluvial sands. The objective of the investigations was to appraise, by drilling and sampling, the two largest deposits--the Guanajibo and Las Mesas. Testing of the smaller deposits was much more restricted. Field investigations consisted of mapping, drilling with power auger, sampling drill-hole sections, and pre-paring samples for chemical analyses, mineralogical studies, and metallurgical tests. The work was financed jointly under a cooperative agreement by the Bureau of Mines and the Economic Development Administration, an agency of the Puerto Rican Commonwealth.

Jan 1, 1959

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date and is being published as a similar series of seven miners' circulars (Nos. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the use of investigations and reports of all accidents.

Jan 1, 1957

By Harold L. Rhodes

The Bureau of Mines has developed a method for determining the H2S content in natural gas samples. A gas chromatograph with a flame photometric detector was used to analyze samples with H2S concentrations ranging from 5,000 ppm to a minimum detectable limit of 0.01 ppm. A mass spectrometer was used to analyze samples containing H2S in amounts greater than 5,000 ppm. Methods are presented for preparing containers for H2S samples and for preparing standards using partial pressure and weighed standard methods, Sample collection techniques are discussed, as are analytical results which illustrate the loss of H2S while in the sample container and provide a basis for evaluating containers used for sampling and standard preparation.

Jan 1, 1979

By Paul M. Price

The Mouat mine, Nye, Mont., was reopened in 1953 by the American Chrome Co. under a Defense Minerals Production Administration contract. Operations were terminated in 1961 after completion of the contract. Mining methods employed during this period are described in detail, and cost data are presented by years for 1953 through 1959. Ultramafic rocks of the Stillwater complex in Montana contain the largest domestic resource of chromite, and the Mouat mine has been the largest producer. Mine reserves were estimated in 1960 to be about 4.4 million tons containing 22.5 percent Cr2O3. The chromite deposits occur as a series of overlapping bands or lenses roughly paralleling the steeply dipping layers of the complex. Only two of the chromite layers have proven to be of economic importance. One layer is 2 to 16 feet wide; the other is 3 to 8 feet wide. Shrinkage stoping was generally used throughout the mine, but various methods of ore breaking, stope drawing, chute construction, etc., were tested to improve output and lower costs. Long-hole stoping proved to have limited use. Breasting down benches, developed outward from the center of the stope with air-leg drills, was satisfactory only in wider stopes. At the close of operations, the company had standardized the use of lightweight stopers to advance a flat back by breaking from a centrally located face. Mining costs were reduced 47 percent during 7 years of operation.

Jan 1, 1963

By Charles P. Lazzara, Alex C. Smith, Richard W. Pro, Mark W. Ryan

The U.S. Bureau of Mines conducted a study to determine if commercially available automatic sprinklers could withstand the high static pressures in deep underground coal mines without leaking and if exposure to the mine environment affected their leak pressures. New sprinklers and sprinklers exposed to the mine environment were subjected to increasing pressures until leakage occurred. The average leak pressures of the new sprinklers ranged from 640 to 2,300 psig and were significantly different for sprinklers from different manufacturers and for different types of sprinklers. Different for sprinklers from different manufacturers and for different types of sprinklers. Generally, standard-response sprinklers withstood higher pressures than fast-response sprinklers. The results indicated that most commercially available sprinklers would withstand the high static pressures in deep underground coal mines; however, they would not provide the same reliability and safety factor as sprinklers used aboveground at or below their rated pressure of 175 psig. The average leak pressures of the sprinklers exposed to the mine environment ranged from 740 to 1,180 psig. The mine environment affected the ability of 66% of the sprinklers to withstand high static pressure New sprinklers were also evaluated at pressures of at least 500 psig for 30 days to determine their ability to withstand long-term exposure to high static pressures; no leakage was observed.

Jan 1, 1993

By John P. Hager

A special inlet system has been developed for a TOF mass spectrometer that allows the equilibrated high-temperature vapors from an atmospheric-pressure flow reactor to be leaked into the ion source of the mass spectrometer without undergoing any compositional changes. Using this flow reactor - mass spectrometer system and a modified transpiration system (one that allows for the carrier stream to be equilibrated with two different condensed samples) a series of fundamental vapor transport studies were undertaken. The results of these studies are summarized as follows: 1. The vapor species in equilibrium with condensed copper (I) chloride were determined to be Cu3C13, Cu4C14, and Cu5C15. The gas mixture is fifty percent tetramer near the melting point (703°K), with the percentage of tetramer decreasing with increasing temperature. The following thermodynamic results were obtained.

Jan 1, 1977

By Gerald T. Homce

Data from the U.S. Bureau of Labor Statistics show that 89 water well drillers died on the job between 1992 and 2002, and 28 of these deaths were electrocutions (Figure 1). In fact, elec­trical accidents are the leading on-the-job killer of water well drillers. The use of electricity is such an integral part of our lives that we usually take it for granted, but if we don?t understand or choose to ignore the hazards associated with electricity, the results can be deadly. Why is electrical shock so dangerous? If the voltage (of a shock) is sufficient to drive electrical current through your body, just 10 milliamps of cur­rent (1000 milliamps = 1 amp) can cause muscles to contract and prevent you from releasing an energized wire or tool in your grip. As little as 30 milliamps of current can paralyze your breathing, and 75 milli­amps can cause your heart to stop pumping blood (ventricular fibrillation). As a comparison, a small bedroom night-light draws about 30 to 60 milliamps. Other factors influence how severely you?ll be shocked if you touch a live electrical circuit, such as the path electrical current takes through your body and how long it flows, as well as your body weight. How much voltage is needed to drive electrical cur­rent through your body? Not much! Generally, any power source at 50 volts AC or higher is considered dangerous.

Jan 1, 2008

By John S. Ball

[A system of analysis for sulfur groups in petroleum distillates has been developed as one phase of the Bureau-of Mines investigation of the more economic utilization of the so-called "black oils" of Wyoming. This problem is being studied by the Bureau of Mines under a cooperative agreement with the University of Wyoming at the Bureau's Petroleum Experiment Station , Laramie, Wyo. Wyoming black oils have high sulfur and asphalt content and usually yield only small percentages of straight-run gasoline. A more detailed description of the properties of black oils has been given in a previous publication (3)3/. The preparation and properties of asphalts from those oils have been described (1, 2), and the effect of thermal cracking and the use of ordinary methods of treating wore discussed in one Bureau publication (4), Although these studies gave considerable insight into the properties and characteristics of black- oils; it was thought t that a more fundamental attack would assist-materially in, the problem of sulfur removal.]

Jan 1, 1941

By John S. Ball

[A system of analysis for sulfur groups in petroleum distillates has been developed as one phase of the Bureau-of Nines investigation of the more economic utilization of the so-called "black oils" of Wyoming,. This problem is being studied by the Bureau of Nines under a cooperative agreement with the University of Wyoming at the Bureau's Petroleum Experiment Station, Laramie, Wyo. Wyoming black oils have high sulfur and asphalt content and usually yield only small percentages of straight-run gasoline. A more detailed description of the properties of black oilshas been given in a previous publication (3)3/. The preparation and properties of asphalts from those oils have been described (1, 2), end the effect of thermal cracking and the use of ordinary methods of treating wore discussed in one Bureau publication (4), Although these studies gave considerable insight into the properties and characteristics of black oil, it was thought t that a more fundamental attack would assist materially in the problem of sulfur removal.]

Jan 1, 1941

By Fremont T. Johnson

Credited with production of more than 164,000 flasks Of quicksilver from 1876 to 1944, the Oat Hill mine has ranked third in output in the United States. During World War II, when the demand for mercury was high, this property was selected for diamond drill with the purpose of increasing ore reserves so that production could be maintained or, if necessary, increased. Although the existence of marginal-grade ore (fill material) left in the stapes and possibly of virgin ore of good grade had suspected in certain parts of the Oat Hill mine, no factual information to tonnage, grade, or location was available. In close cooperation with the Federal Geological Survey, the Bureau of Mines studied old records and the few available incomplete maps. Diamond drilling began in November 1943 and was completed in December 1944. Twenty-eight holes aggregating 8,121 feet were drilled, in only parts of the promising areas disclosed by the study of the data available. Detailed data on the work done by the Bureau as well as a brief history of the property and some operating details are described in this report.

Jan 1, 1949

By Frank E. Chase, Deno M. Pappas, Christopher Mark

Multiple seam interactions are a major ground control hazard in many U.S. underground coal mines. The two most common types are: • Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the primary concern, and; • Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The National Institute for Occupational Safety and Health (NIOSH) has completed a major study aimed at helping to identify the location and likely severity of these interactions. In the course of field visits to mines throughout the U.S., more than 300 multiple seam case histories were assembled into the largest data base of multiple seam case histories ever collected. These data were analyzed with the multivariate statistical technique of logistic regression. The study also employed LaM2D to estimate the multiple seam stresses, ALPS and ARMPS to determine pillar stability factors, and the CMRR to measure roof quality. The study resulted in the development of a computer program, called Analysis of Multiple Seam Stability (AMSS), which can help mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. AMSS first evaluates pillar design by calculating the single seam Stability Factor (SFSS) using ALPS or ARMPS. It also automatically generates a LaM2D analysis that provides the additional multiple seam stress so that the final, multiple seam SFMS can be determined. The second part of the AMSS procedure builds upon the statistical findings that overmining is much more difficult than undermining, isolated remnant pillars cause more problems than gob-solid boundaries, and weaker roof significantly increases the risk of multiple seam interactions. AMSS quantifies these effects and predicts the outcome in terms of three levels of risk: GREEN (where a major multiple seam interaction is considered unlikely), YELLOW (where adding a pattern of cable bolts or other equivalent supplemental support could greatly reduce the probability of a major interaction.), or RED (a major interaction should be considered likely, and it may be desirable to avoid the area entirely).

By L. Bruce McDonald

This Federal Bureau of Mines publication is a statistical analysis of all surface and underground coal mine fires reported in the United States from 1950 to 1977. Accounts of selected nonreportable fires and opinion data gathered via interviews with mine safety directors were separately analyzed. Both reported and nonreportable fires were analyzed by time trends, State, ignition source, burning substance, location in mine, equipment, detection, duration, injuries, fatalities, and successful extinguishing agents. It was found that the majority of all mine fires were electrical in origin. The equipment most frequently involved in underground fires was conveyor belts, and in surface fires, it was crushers and/or breakers. Underground fires occurred most often near the working face. Water and hand-portable extinguishers were the most common methods of extinguishment.

Jan 1, 1980