Search Documents

By M. E. Poad, M. M. McDonald, J. C. Johnson, W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-element method for evaluating shaft pillar mining plans and shaft stability. This report focuses on mine measurements and calibration of the two-dimensional computer model and is the second in a series of three Reports of Investigations describing the Ross shaft study. In this study, borehole extensometers and other instruments were installed to provide data for model verification and to monitor the shaft. Results of the recalibrated two-dimensional model (UTAH2) confirmed the premining stability evaluation. However, after mining began, concern was expressed because cracks and other signs of ground motion appeared at considerable distances from the area of active pillar mining. In part 3 of the study, an intense three-dimensional modeling effort using UTAH3 was initiated. The results again showed that the observed effects were within expectations and that the shaft would remain safe. Three-dimensional analyses of alternative pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought.

Jan 1, 1995

Objective To develop safety training tools for mine health and safety trainers that fill gaps in currently available materials and help capture the wisdom and knowledge of “expert miners.” Background NIOSH began a series of stakeholder meetings in 1998 to determine what research was needed to improve miner health and safety. One of the more common concerns among stakeholders was a critical lack of appropriate training materials applicable to metal/nonmetal mining. Participants provided many insights into what effective training materials should include and how materials could best reach both new and experienced miners. The most important factors were that any materials be realistic and interesting and that some way must be found to capture the wisdom of expert miners before they retired. Approach NIOSH researchers chose videos as the best means of achieving these training goals. Over the past 3 years, NIOSH has produced three training videos that present information on safe work practices in underground mines: handling explosives, recognizing roof hazards and using proper scaling techniques, and installing ground supports. The last two videos, “Rock Falls—Preventing Rock Fall Injuries in Underground Mines” and “Miner Mike Saves the Day—or—Ground Support…It’s Important,” have won Alice Hamilton awards, NIOSH’s highest recognition of Excellence in Occupational Safety and Health, in the Educational Materials category. Two new videos are now being released. Both of these videos were shot completely in operating underground hard-rock mines and used expert miners to tell the story. Hazards In Motion The first, “Hazards in Motion,” deals with the dangers of working around mobile equipment in an underground mine. Ben, a new trainee, refuses to pay attention in his 40-hour New Miner Training class, and when the class takes its first trip underground, he wanders off and finds himself in many dangerous situations. He encounters many experienced miners who both chew him out for his unsafe attitude and give him advice and information on how to survive around mobile equipment. Many common pieces of equipment are shown, including haulage trucks, LHD=s, tracks and trains, slushers, skips and hoists, and air doors. The dangers of ignoring signals and of horseplay are also included. After nearly losing his life numerous times, Ben learns his lesson with the help of the Safety Angel, an experienced miner who looks suspiciously like his safety trainer. Ben’s Safety Angel saves his life repeatedly, teaches him how to work safely around these common conveyances, and introduces him to experts who have specific safety tips. Ben learns the error of his ways and vows to be the safest miner in the mine. “Hazards in Motion” is approximately 30 minutes long. Hidden Scars The second video is the first in the NIOSH “Expert Miner” series. “Hidden Scars” is a narrative interview with Don Capparelli, a miner and supervisor at the Sunshine Mine in north Idaho. This video captures the story of a fatal rock burst in May 1994, when Don was seriously injured and his long-time partner, Jimmy Findley, was killed. “Hidden Scars” is a very powerful story. Don Capparelli shares the physical and emotional pain he lives with daily as he relates the events leading up to the rock burst that took the life of his best friend and partner. This video is an excellent reminder of the human cost of uncontrolled accidents and the hidden scars that survivors must deal with for the rest of their lives. It runs approximately 25 minutes.

Jun 1, 2001

By Patrick A. Hamilton

This Bureau of Mines report delineates the coal reserve base of anthracite, bituminous and subbituminous coals, and lignite, by mining method and sulfur content, for coal-bearing States west of the Mississippi River. The parameters used to establish the reserve base definition are the result of a joint agreement by the Federal Bureau of Mines and the U.S. Geological Survey. The reserve base of low-sulfur coal, =10 percent sulfur, is 167,324.5 million tons; medium-sulfur coal, 1.1-3.0 percent sulfur, is 37,531.5 million tons; and high-sulfur coal, >3.0 percent sulfur, is 11,244.1 million tons. The reserve base of coal with an unknown sulfur level is 18,323.0 million tons. The percentages of deep and strippable coal are 56 percent and 44 percent, respectively. The basis for reserve base estimates and analytical data for this report was the Fuels Availability System, a Bureau of Mines data bank containing numerous data tin fossil fuels. Information contained in the system was obtained from publications of the Bureau of Mines, U.S. Geological Survey, State agencies, private publications, and company data.

Jan 1, 1975

By M. John Brodie

This report reviews the regulatory environment as it pertains to tailings management and disposal from mining operations, excluding coal and placer gold operations, in the state of Alaska. It is based on the EPA's staff position on an effective program to regulate mining wastes as presented in the May, 1990 Strawman II document, The unique conditions which occur in parts of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a railings disposal facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection are examined.

Jan 1, 1992

By J. J. Jakosky, D. H. Zellers

"IntroductionThis paper is the seventh of a series describing an investigation being conducted by the Bureau of Mines on underground communication. A review of past work and results obtained has been published. The present paper deals with a study of line-radio or wired-wireless methods of communication, herein electrical energy is transmitted by metallic conductors.The use of line-radio over metallic conductors has been practiced for a number of years, and at present is being used on a large scale in long-distance carrier-current telephone and telegraph. The early work of the U. S. Army Signal Corps and the Bureau of Standards in using ordinary radio transmitting and receiving apparatus for communication over metallic conductors was been descried. Later publications describe commercial applications, and an excellent treatise and resume is given by E. Colpitts and C. B. Blackwell.Scope of ReportThis report contains (1) a discussion of the chief factors affecting carrier-current transmission, with particular reference in application to underground communication for mines; (2) a description of typical underground circuits used for power and lighting; and (3) description of apparatus used and results obtained in line-radio experiments in coal mines near Pittsburgh, with circuit diagrams, and conclusions as to power requirements and limitations for mine use."

Apr 1, 1925

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers in their Resource Development Navigation Study, the U.S. Bureau of Mines (Bureau) examined the potential for mineral development near ten Alaska port sites. This report presents the results for the following four sites: Balboa Bay, Beluga, Lost River, and Point MacKenzie. There are 579 known deposits within the area considered for these ports. The majority of the deposits are located within a highway/railroad corridor examined for the Point MacKenzie port site. Based on the current level of knowledge, coal deposits near the Beluga and Point MacKenzie port sites are most likely to be developed in the near future. This conclusion is based on the fact that coal projects in these areas are actively being pursued for development. The mineral wealth surrounding the four port sites is substantial. Mine models were used to examine the potential for mining tin, gold, silver, copper, and molybdenum. The models were based on published reserve and grade data and therefore do not include proprietary company data which, if available, would likely change the analysis results. Of the models examined, the tin placer mine model developed for the Lost River port site proved to be closest to being economic.

Jan 1, 2011

[RESULTS OF THE PRIMARY CONVENTIONAL PERFORMANCE AND COST MODEL OF THE UNIT OPERATIONS OF UNDERGROUND PERCUSSIVE DRILLING AND BLASTING]

Jan 1, 1977

By John P. Capp

The feasibility of simultaneously burning several paths through a coalbed to develop a multiple path underground gasification system was investigated by the Bureau of Mines during two experiments, Boreholes were drilled through the overburden and into the coal and arranged in a circle approximately 50 feet from a central borehole. In the first experiment, in an area which had previously been hydraulically fractured,5 air was injected at the center borehole. The coal was ignited at the other boreholes and the fire fronts traveled toward the center, counter to the flow of air, to backward burn paths through the coalbed. Two paths were linked during the first 5 days of operation. The outlets of these two paths were throttled and air pressure was increased to maintain the flow of air, but no other linkages were made. Fourteen days after the two linkages these two paths were opened and gasification was carried on for 10 days, but with only moderate success. In an effort to overcome operating difficulties air was injected at the peripheral boreholes, and the gases were drawn off at the center borehole. Reversed flow operations continued for 12 days and two more paths linked. The heating value of the gas generally was higher than 100 British thermal units per standard cubic foot (B.t.u. per std. c.f.). Because only four of seven paths linked, however, the entire system could not be evaluated with respect to product-gas output and recovery of energy.

Jan 1, 1961

By C. W. Owings

One phase of Bureau of Mines health and safety work is promotion of the use of safe and effective dust-collecting devices in connection with rock drilling in coal mines. To insure that adequate equipment of this type is available to the coal-mining industry, the Bureau of Mines conducts investigations and issues approvals for dust-collecting equipment that meets the requirements of a schedule established for testing dust collectors intended for use in connection with roof drilling for roof bolting and for other rock drilling. 6/ Performance tests are conducted under the provisions of this schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for approval and lists drill-dust collectors that have been granted approval as of January 31, 1956. The addresses of manufacturers of approved devices are listed alphabetically at the end of this circular.

Jan 1, 1956

By C. S. Allbright

This report gives the results of analyzing three groups of crude shale oils by the Bureau of Mines procedure:4/ (1) Oils produced by standard Fischer assay determinations on oil shales from Brazil (Paraiba Valley) and the United States (Colorado); (2) oils produced from Brazilian shale by different retorting methods; and (3) oils from high-temperature retorting of Colorado oil shale in the Entrained Solids retort. It is the second in a series presenting data obtained by analyzing crude shale oils from various sources. The series furnishes information on the general characteristics and compositions of a wide variety of shale oils. Use of a standard analytical method on all samples facilitates comparison of different oils. The 18 oil samples analyzed in this project comprised 3 from assays of Brazilian and Colorado oil shales in the Fischer retort, 9 obtained by processing Brazilian shale in various other units, and 6 from entrained solids retorting of Colorado shale at 1,000° to 1,500° F. The crude oils from Brazilian shale contained about half as much nitrogen as the Colorado oils. Properties of the Fischer assay oils from Colorado shales agreed with some data that relate grade of the oil shale with properties of the crude oil from the Fischer assay. Comparison of results from Fischer assays of oils from the foreign and domestic shales shows that the oil from Brazilian shale contains more low-boiling material and less residuum than either of the two from Colorado shale. This fact is reflected in lower specific gravity, viscosity, and carbon-residue values for the Brazilian oil. Retorting Brazilian shale in the Entrained Solids unit at 1,120° F. produced an oil whose boiling range was generally lower than the boiling ranges of oils obtained by processing in three other retorts at conventional temperatures. The quality of crude oils from high-temperature retorting of Colorado shale in the Entrained Solids process varies with retorting temperature. As the temperature is raised within the range 1,000° to 1,500° F., the amount of the naphtha fraction in the crude oil increases to about 35 percent and the aromaticity to 98 percent.

Jan 1, 1956

By Ivette E. Torres

Aruba, formerly a. part of the Netherlands Antilles, separated on January I, 1986, and became an autonomous part of the Netherlands. Full independence of the island from the Netherlands is scheduled for 1996. In this chapter, however, Aruba's statistics are included with those of the Netherlands Antilles. Tourism continued to be the main industry of the island, which continued to depend heavily on imports, mostly from the United States. During the year, the Government was preparing legislation to regulate the exploration of oil deposits in the relatively shallow sea around Aruba.

Jan 1, 1989

By R. C. Ellman

Since successful industrial lignite-burning equipment was developed in 1925, the commercial use of lignite as a fuel for power plants has increased. It has proved an entirely satisfactory fuel for generating power and can be burned efficiently by various methods.4/ Equipment to fire pulverized lignite was installed and used successfully at the Trinidad Station of the Texas Power & Light Co. as early as 1926. The lignite was predried in steam-heated grid driers before pulverizing.5/ This method of firing was used later in the Comal Station of the San Antonio Public Service Commission.6/ Both stations, however, have since been converted to use other fuels. Units for pulverizing and drying lignite are relatively new in the lignite-consuming region of North Dakota. The air which sweeps the pulverizer and transports the pulverized product to the burners is preheated to dry the lignite during pulverization. The first unit was installed in 1948 in one of the two boiler units of the Crookston Station, Otter Tail Power Co., Crookston, Minn.7/ In 1951 the 30,000-kw. W. J. Neal Station, Central Power Electric Cooperative, Inc., Voltaire, N. Oak., was designed and constructed for firing pulverized lignite exclusively. It is the largest lignite-fired, power-generating station in North Dakota. The 44,000-kw. Lewis and Clark Station of the Montana-Dakota Utilities Co., Sidney, Mont., is fired by a similar pulverizing system. Operation of this plant was begun in October 1958. At Fergus Falls, Minn., the 53,500-kw. Hoot Lake Station of the Otter Tail Power Co., also using a pulverized lignite-firing system, began operating in September 1959.

Jan 1, 1961

By Allen S. Smith

Analysis of the helium content of a natural gas presents more than the usual difficulties encountered in applying the thermal--conductivity method because of the relatively small amounts of this inert gas present and the wide variation in the other constituents. However, the numerous advantages of this method and its adaptability to continuously recording and control instruments make it worthy of consideration. A specific application of the method described yields quantitative results only when used with gas mixtures of known qualitative compositions which vary within predetermined limits. Periodic analyses for the helium content of a producing gas well may be conveniently made by an absorption method3/ and a continuous analytical method is not necessary for this purpose. Natural gas containing 1.75 to 1.90 percent of helium produced from Government-owned wells is processed in the Amarillo (Texas) Helium Plant of the Bureau of Mines. The helium extracted in the plant is supplied to the Army and Navy, and the processed natural gas is sold to a commercial gas company4/. As complete recovery of the helium in the raw material is not economically practicable, the processed gas contains 0.1 to 0.3 percent of helium, depending upon conditions of operation;- Production is checked against the helium removed from the gas, which before the installation of the thermal--conductivity apparatus was calculated from the analysis of a cumulative sample of the processed gas. As conditions of operation affect the residual helium content to a large extent, a composite sample was an uncertain index of the efficiency of the process.

Jan 1, 1934

By ARCH L. FOSTER

The rapid increase in the mmber of automobiles during the last 25 years has resulted in the insistent and growing demand for better roads of more permanent construction. Some form of State license for the operation of automobiles has been in effect almost from the time of the first "self-propelled" vehicle, and some part of the revenue derived from the sale of these licenses has been applied to the maintenance and construction of roads. However, to obtain funds with which to build their present highway systems, the individual States have resorted to the taxation of gasoline. The first State to adopt a gasoline tax was Oregon, the law becoming effective February 25, 1919. By 1928, all of the States except two had levied taxes on gasoline at rates varying from 2 to 5 cents per gallon. New York and Massachusetts passed gasoline tax laws which became effective in 1929. Regulations governing the quality and the methods of handling gasoline and other petroleum products sold in the States have also been adopted by 29 States; many of these laws antedate the adoption of a gasoline tax. The variations in motor fuel speci- fications and methods of test have been pronounced in the several States. The Bureau of Mines, in making certain technical studies of the rasolines marketed throughout the United States, the results of which are reported in its semiannual motor gasoline surveys and other reports, has had occasion to obtain and compile all of the present (April 1, 1931) tax and pection laws of the several States which relate to motor fuel and other petroleum products. To facilitate the use of this material and to obviate the need in most cases of reading the complete text of the laws as published by the States, the pertinent information was arranged in tabular form for cly reference. 3 Although digests of States gasoline tax laws' are available and copies of the complete laws can be obtained from the State agancies in charge of the enforcement of gasoline tax and inspection laws, it is believed that

Jan 1, 1932

By Noel N. Moebs

Bureau of Mines studies of mine roof fall problem in the Pocahontas No. 3 Coalbed of southern West Virgania and southwestern Virginia have established that type and sequence of rock are significant factors in roof competence. The poorest conditions occur where the immediate roof consists of slump structures and slickensided rock. The best conditions occur where the roof consists of a sequence that coarsens upward from shale to massive sandy shale. A small manual of color photographs of rock types was devised to aid in identifying drill cores. Proper identifications should enhance the prediction of areas of potential roof problems in advance of mining.

Jan 1, 1981

By O. Q. Leone

Excellent metal quality, with lower power requirement, is attained in electrorefining titanium by using internal heating of the fused-salt bath. An internal heater provides more effective heat utilization, simplifies structural components in cell design, and prolongs cell life by eliminating direct application of heat to the cell container. This Bureau of Mines report covers one phase of the research in progress at the Electrometallurgical Experiment Station at Boulder City, Nev., for improving the techniques and lowering the total power requirement for electro-refining titanium metal.

Jan 1, 1959

By K. P. Wang

Mining and metallurgy have had a long history in China, and resources there have always been considered promising. Under the People's Republic of China (PRC), a remarkable industrial renaissance is underway that should further gain momentum in the years ahead. Rapid development of minerals have not only brought the PRC prominence in industrialization, but also in world affairs. Chinese mineral developments, especially petroleum, have been increasingly in the news. Oil and gas may have great potential, but a very large coal industry is already in existence. The steel industry ranks fifth or sixth in the world. The PRC is also prominent in fertilizer, cement, and salt production. The export metals are well known. Also, the country is buying heavily in nonferrous base metals. The need to know and the intense interest in the subject have prompted this study. The world significance of Chinese minerals is pointed out. The history of growth and PRC's mineral supply position are reviewed. Evaluations are made of policy considerations and regional and technical factors affecting mineral development. PRC's mineral trade and efforts to obtain equipment, supplies, and know-how are assessed. Specific reviews are made of major mineral sectors, including coal and power, oil and gas, iron and steel, nonferrous metals, industrial minerals, and fertilizers and chemicals. The overall outlook is summarized.

Jan 1, 1975

By R. S. Dean

The brief resume of the activities of the Metallurgical Division that appears annually in its progress reports series serves a useful purpose by making available a rather comprehensive but concise recapitulation of the current work, and publications of the division. An unprecedented opportunity to attack the problem of producing ferro-grade material from low-grade domestic manganese ores effectively was provided by the act designated as Public 667 of the 76th Congress of the United States, approved June 26, 1940, which made available an appropriation for "Expediting Production of Equipment and. Supplies for National Defense." Although the funds were not immediately available to the division, good progress has been made in the, solution of the many and diverse problems presented in the studies undertaken to determine the best methods for the recovery of useful products from a wide variety of manganese ores.

Jan 1, 1941

By D. A. Larson

The Bureau of Mines conducted basic experiments to study the process of crack propagation with a wedge indenter. The work was conducted under plane stress conditions in a hard, brittle limestone. The purpose of these experiments was to first gain an understanding of the basic crack propagation process under a sharp indenter, and second, to determine how the crack propagation process could be used to improve mechanical fragmentation systems. Three methods of rock fracture with the wedge indenter were investigated in this program. These were the confined indentation tests, the unconfined splitting tests, and the edge chipping tests. The confined indention tests represent worst case conditions for crack growth and formed the lower bound on fracture efficiency. The unconfined splitting tests represented best case conditions and fixed the upper bound of fracture efficiency. The edge chipping tests represented an idealized fragmentation process based exclusively upon the highly efficient fracture propagation process. Edge chipping achieved a specific energy of 25 in lb f/in3 compared to conventional drag cutters, which required a specific energy of at least 2,385 in·lb f/in3? Thus edge chipping is up to 100 times more efficient than conventional drag cutting. Because of these promising results, more work is planned with the fracture propagation process in three dimensions.

Jan 1, 1987

By Richard F. Zaffarano

The Bureau of Mines compiled information for the nonspecialist about natural gas liquids recovery from hydrocarbon streams in natural gas processing plants. Attention is directed to the impact of the technology of processing and the quality of gas processed in view of the increased availability of natural gas for processing. Significant changes in product and market trends within the natural gas processing industry are highlighted. Fixed capital-plant costs for grassroots, refrigerated-oil absorption and conventional adsorption schemes, adapted from published studies, are presented giving ranges of cost estimates for medium-sized plants. Marketed products of the natural gas processing industry are briefly discussed in relation to automotive air pollution problems and approaches to their control.

Jan 1, 1970