Search Documents

By D Vidyarthi

Blasting is the most important activity in the mining industry, the world over. It is a well known fact that only part of the explosive energy gets utilized in causing the actual rock fragmentation. The rest of it gets converted into blast-induced ground vibrations and noise. Though blast vibrations cannot be totally eliminated, it is possible to minimize them by optimization of blast parameters. This paper highlights various in-house efforts put forth by the author towards site specific blast optimization and the monitoring of blast vibrations. It also deals with the prediction curves developed by regular regression analysis for the prediction of ‘blast vibrations’, ‘peak particle velocity’, ‘safe charge’ for various blasts.

Jan 1, 2007

By Choon Sunwoo, Chang-Ha Ryu

There are various methods available for the recovery of dimensional stone in open pit quarries. Explosive blasting has more advantages in the economic point of view over the other methods but was not widely used in Korea because owner was concerned about much economic loss when it failed. Several years of efforts have been made in order to develop more effective cutting methods and to spread to the quarries for strengthening the competitiveness in the market. Rock cutting by jet flame and black powder was generally used in the early stage. Black powder was applied to cut the last horizontal plane after forming other vertical planes using the jet flame. Jet flame operation, however, is time consuming and produces excessive noise, and as the result, brings adverse effects on the operator as well as the complaints from the residence adjacent to the quarry. Some mechanical methods such as the slot drill, diamond wire saw or in-situ scale of diamond saw cutting were introduced. Most effective cutting methods using the explosive blasting were developed and applied successfully. Black powder was replaced with the detonating cord. A new air decking technique where plug was not used was developed. This paper reviews the technology for dimensional stone cutting and case study in Korea.

Jan 1, 2003

By Mark A. Williams

"This paper was originally intended to be a presentation of a case study of two surface bituminouscoal mines in the southern Appalachian coal fields located within five miles of each other. These mines were nearly identical in every aspect from geologic setting to equipment application. Althoughrepresentatives from each mine desired to participate in the preparation of this paper through support in providing background information and in review and editing, it was later concluded that, due to the environmental sensitivity associated with each mine, it may not have been a good decision to present this case study in a public forum."

Jan 1, 1994

By Michael Mann

Two house trailers and a modem modular house, all pillar-supported with cantilevered perimeters, were monitored for structural response to vibrations from surface coal mine blasts. Due to the large blast site distances, peak particle velocities measured in the ground beside the houses did not exceed 0.32 ips, and airblasts did not exceed 106 dB. However, the structures responded significantly to the ground vibrations, with maximum high-comer amplification factors as high as 8.5 in the horizontal directions. Vertical structural responses were as high as 10 times the vertical peak particle velocities in the ground, but appeared to be driven more by horizontal ground motions. No measurable airblast responses were observed. The natural frequencies of the structures ranged from 5 to 10 Hz.

Jan 1, 2000

By Gary Cavanough, Stuart Addinell, Hector Parra

Drilling deep, straight, accurate holes in hard rock to achieve efficient blasting is a challenge for the mining/quarrying industries with short holes normally drilled using “top hole hammer” (THH) and deep holes using “down the hole Hammer” (DTH).

Jan 1, 2013

By Laura Bustemante, Bruce Vandenberg, Fred Huettig

Recent advances in solid-state, field portable, fast framing video camera systems and PC based frame capture hardware now allow blast imaging up to 1000 frames per second. Up to 8 seconds of data can be stored directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the KineView 1256P system and compare these with the analogous aspects of fii based cameras.

Jan 1, 1998

By Roger S. Jackson

"This study interprets vibrations produced by single underground shots, recorded on surface by 135 digital seismographs laid out in four linear arrays. Several vibration anomalies were observed and are investigated. A novel method of displaying the blast-induced vibration iso-contour data relative to the three-dimensional representations of the geological rock units and structures leads to the following interpretations:• The identified faults commonly dampen or amplify vibrations, on the evidence of the peak particle velocity,• Strong anisotropy of geologic formations produces different vibration attenuation in the various directions of interest,• Low-vibration “depressions” can be related to the presence of faults, and• Higher vibration levels than expected based on ‘scaled-distance’ principles are observed close to intersecting faults.The interpretations from this study document a better understanding of the geotechnical influences on blast induced stress wave propagation in a geologically complex area. The practical benefit of this understanding is better control of surface vibrations, experienced from underground mining activities."

Jan 1, 2010

By M. Hagfors

When establishing an underwater testing site for the energy measurements of the explosives, the dimensions of the measuring pool have to be measured to find out what is the maximum weight for the test charge. Secondly one has to decide the distance between the pressure gauge and the shooting point. Thirdly the pool has to be calibrated because of the reflections of the explosions by measuring the bubble periods of the calibration charges. The calibration shots can also be used to estimate the minimum weight of the explosive charge for the reliable energy measurements by calculating the shock, gas heave and total energy values and their standard deviations.

Jan 1, 2007

By Robert Hopler

That some time in the year 1872 there was organized an association composed of practically all of the manufacturers of gunpowder and other high explosives in the United States, the members of which said association were as follows: E. I. du Pont de Nemours & Co., The Hazard Powder Company, Laflin & Rand Powder Company, Oriental Powder Mills, American Powder Company, The Miami Powder Company, and Austin Powder Company of Cleveland, all of which or their successors are defendants herein; that the object and purpose of said association was the elimination of all competition between the members thereof in the shipment and sale of gunpowder and other high explosives among the various States and Territories of the United States; that the only manufacturers of gunpowder and other high explosives which did not join such association at the time of its organization were the California Powder Works, The Sycamore Manufacturing Company, and The Lake Superior Powder Company, but your petitioner alleges that each of said three last named companies

Jan 1, 2008

By Jack Eloranta

The winning of metals often requires fine grinding of very hard ore. The US Bureau of mines measured compressive strengths exceeding 100,000 PSI (700 MPa) in Minnesota taconites. Grinding down to 300 mesh (50 µ) is required for some fine-grained taconites. While other metal ores may not be as strong, significant grinding costs are the rule rather than the exception. One author recently reported that a 7% drop in grinding costs would fully offset a doubling of the drill and blast budget. Another author found that drill and blast costs were 13% of the costs of producing iron ore concentrate while fine crushing and grinding were over 60% of the cost of producing concentrate.

Jan 1, 2013

By Steve Dillingham

PHYSICAL BLAST DATA Pattern Description All measurements related to the description of the physical blast pattern must be made with the mind-set that it has to tell a powerful factual story enabling a future accurate reconstruction of the event. A case has never been lost because too much factual information was available to assist investigators. An accurate physical description of the pattern must be provided based on the blaster’s observations of the pattern actually loaded. The blaster must measure the pattern size, depth, face heights, etc., recording only accurate results. All too often, a blaster records simple pattern sizes and information relayed to him or her from the driller, or from a phone call into the office the night before for powder pre-load inventory purposes. If a pattern was actually measured on the job site by the blaster to be 8.5 x 9.5’, it may, in fact, originally have been ordered at 9’x9’, 8’x9’, or 9’x l0’. In a claim situation, particularly flyrock, recording a “generalization” of what was loaded could result in an interpretation of a blaster’s negligence due to “not knowing or caring” what the actual pattern was, and not loading appropriately for conditions. It is important to remember that other documentation exists such as a drill log from a contract driller or mine records that may provide a different interpretation of the loaded pattern.

Jan 1, 2002

By Chulgi Suk, Hoon Park, Hyonsoo Kim, Hakman Kim, Sangho Cho

Dust emission from blast demolition and other construction activities can be a nuisance; it is widely recognized that fine particles less than 10 µm in equivalent diameter (called PM10) may cause health problems. Mist spray systems, such as rain guns, sprinklers, water/surfactant sprays (or foams) etc., are some of the most effective dust suppression methods. A large amount of research has showed that when water droplets are produced in an equal amount to that of dust particles, the airborne dust is suppressed by the agglomeration of dust and mist particles. A method for generating micro-sized mist from water, achieved by the detonation of explosives in the water tube, was suggested and is called the ‘detonationdriven water bag burst system’. There are many experimentally observed limitations of the explosioninduced water break-up process. The water bag explosion tests were simulated using the AUTODYN software, in order to investigate the aerosolization mechanisms of the detonation-driven water and water break-up process into micron-sized droplets. As a result of the numerical analyses, the diffusion direction of water when detonating in the central interior part of water tube was radioactive and significantly stronger than when detonating in the bottom exterior part; this is due to the compressive flow of the volume change inside of the water tube, which resulted from the blasting wave inside of the tube, as well as the reflected pressure on the ground. Blast tests of full-scaled reinforced concrete columns were conducted to verify the effectiveness of the suggested detonation-driven water bag burst system. The water breakdown and dispersion that occurred while blasting the reinforced concrete columns were observed using a high-speed camera, and dust generation was monitored using four density detectors. The suggested detonation-driven water bag burst system showed that the average dust density decreased by up to 7 mg/m3.

Jan 1, 2016

By Neal Lee, Braden T. Lusk, Jhon Silva-Castro, Patrick J. Jenks

"Timing and charge sequence are very important for optimized blast design. Traditional nonelectricinitiation systems have moved the industry toward a system of delays consisting of hole-to-hole androw-to-row timing sequences that mimic the application of nonelectric surface delays or dual delayinitiator systems that have been prevalent in the blasting industry for many years. The increasedutilization of electronic detonators allows for the use of Regular Rhythmic Timing (RRT) utilizing onlyone delay between charges and a selected charge firing sequence. The hole to hole and row to row (HHRR) timing method has been utilized for blasting optimization and allows for simplistic changes to the tie in phase of the blasting sequence. When using this traditional timing methodology, for some specific cases related to the number holes and rows, crowding occurs in the delay between charges with subsequent increase in the peak particle velocity (PPV) produced by the blast. This is in contrast to RRT where the timing between the delays remains constant."

Jan 1, 2016

By Kevin Phelps, Jason Baird

When dealing with high velocity projectiles, the ability for researchers to accurately and precisely measure the velocity of the projectile is of great value. This report will analyze three different methods of recording high velocity projectiles for: their ability to record velocity data, pros and cons for each method, and any possible bias or limitations that would result. Method 1 uses a Phantom V10 high-speed video camera and a velocity reference screen to record the projectile’s path and proprietary Phantom software to analyze the data and determine velocity. Method 2 utilizes two break screens. This method, consisting of strung copper wire as the break material, is one that has been used in the past by Missouri University of Science and Technology (MS&T) researchers in assisting in finding velocities of high-speed projectiles. Method 3 is a pair of make screens, similar to Method 2 in that two screens were used for each test but relies on a projectile making a circuit between two sheets of metal separated by an insulation layer, to find a velocity. All three methods will be used simultaneously in each shot to rule out any projectile differences in subsequent shots. Projectiles of three different relative velocities, low, medium, and high, will be fired and analyzed to determine strengths and weaknesses of each method.

Jan 1, 2014

By Jackson R. Pressley, M L. Hopkins, R E. Danell, N T. Moxon, Andrew Bowman

Efficient and cost effective blasting is achieved by closely matching the explosive energy to the strength of the material in which it is being used. Although there are many empirical relationships wich approximate this situation complete the blast optimization can only be achieved by quantitatively assessing explosive/rock interactions and explosive performance. The performance of an explosive is essentially governed by its velocity of detonation or the rate at which the detonation wave travels through the explosive column.

Jan 1, 1991

By D Frantzos, J J. Cotter, H Tammemagi, J B. Codrington, J Kaasalainen, A C. Webster

"Exploshres Technologies International (ED) is developing an instrument called ROCSCAN which isplanned to have broad application in both blasting and rock mechanics. The purpose of this paper is to outllne the background that has led to the development of ROCSCAN, describe its objectives and to present a progress report on the work to date. Some of the potential applications of ROCSCAN will also be reviewed."

Jan 1, 1989

By Sam Kangwa, Thomson Sinkala

Th e re are three basic types of hole deviations in long hole d ri l l i n g , n a m e l y collar i n g , alignment and tr a j e c t o r y dev i a t i o n s . In mining, the accur a cy in drilling has a significant effect on the effi c a c y and economy of mining oper a t i o n s . This ar t i cl e d e s c ribes the types, s o u r ces and effects of hole deviations in mining oper a t i o n s . The art i cle further demonstrates the economic consequences due to hole dev i a t i o n s .

Jan 1, 2004

While ring-blasting techniques offer substantial benefits, there are intrinsic problems that are exacerbated when large blocks of ore are mined in attempts to improve the production economics. These problems relate to both the convergence of holes around the ring drive and the charging of up-holes. The size and shape of the ore block concerned should be carefully considered so that good drilling, patterns can be achieved. The hole diameters chosen, both affect and are affected by the size of the ore block. The explosive selected depends on the hole diameter and together with the diameter, determines the nominal drilling pattern. Ring-drilling patterns are best derived through the use of computer software together with engineering judgement. The loading of explosive is necessarily high, and charging patterns require careful thought if overcharging is to he minimised and adequate energy is to be available at all parts of the ore block. Initiation systems are critical to the blasting results, but sub-optimal systems must be adopted if collar priming is practised. In view of all these factors, idealised guidelines can be given for ring design, but it should be recognised that developments in technology may in time change some of these parameters.

Jan 1, 2000

By Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Mehmet Aksoy, Kagan Ozdemir, Adiguzel Deniz

This paper presents the results of ground vibration measurements induced by blasting during the construction of the Istanbul Kadiköy-Kartal metro tunnel which has been driven at a depth of approximately 20-40 m deep under a highly urbanized region of Istanbul city in Turkey. This tunnel is being constructed by a joint venture group. The formation encountered during the construction is classified as hard and strong rock by laboratory and field tests performed by the joint venture group. Within the scope of the study, for the prediction of the peak particle velocity and to determine the slope of the attenuation curves together with the maximum charge per delay for the S4 shaft tunnels and S12 shaft tunnels of this tunnel route, ground vibration components were measured carefully by using four vibration monitors (Instantel Minimate Plus model) during the advancement of the tunnels which required blasting. The particle velocities and frequency values of all blast events are evaluated according to the United States Bureau of Mines (USBM) and German DIN 4150 Norms in order to predict, and compare the influence grades to the neighbouring buildings, and structures. Also, data pairs of scaled distance and peak particle velocity obtained from 114 records at S4 shaft tunnels and 79 records at S12 shaft tunnels were analysed statistically. Empirical relationships with correlation at the 95 % confidence interval were established for different rock units (diabase and arkose) and suggested for the test sites in order to estimate particle velocity of the ground vibrations.

Jan 1, 2007

By D T. Froedge

At the 1990 Symposium of the Society of Explosives Engineering, D.T. Froedge, President of GeoSonics Inc., presented a paper entitled "Differential Topographic Vibration Isomapping", which detailed the capabilities of GeoSonics' new Iso-Seismic Service. In this paper Mr. Froedge described how one hundred or &ore free-standing miniature seismographs called Micro-Seis Units, randomly positioned around a blast, could accurately reveal the effects of sub-strata geology on surface ground vibrations. The paper went on to note the "regression analysis of scaled distance versus recorded particle velocity" as being an inadequate predictor of peak particle velocity. This is due to the fact that the calculated "regression analysis" formula for any site is predicted on the wars; case assumption because of a homogeneous and symmetrical sub-strata geology, a condition that rarely, if ever, exists.

Jan 1, 1992