Search Documents

By D. R. Nagaraj, Raymond Farinato

Water constitutes one of the most valuable resources employed in mineral recovery and processing. Identifying potential problems encountered in mineral processing in waters unusable for drinking or agriculture (including seawater and even hypersaline waters), understanding chemical factor interactions, and optimization of flotation reagents will greatly expand our ability to create more sustainable beneficiation technologies. The current paucity of our knowledgebase regarding high salinity effects on flotation clearly signals a need for a significant research effort. We report here results of a study designed to probe effects of pulp chemistry on metallurgical performance in the flotation of Cu and Cu-Mo ores in saline waters. The results clearly demonstrate that pH (more correctly dosage of pH modifier to target a pH set point) has the most significant effect on Mo recovery when using seawater. This is linked to the formation/precipitation of Mg(OH)2 when pH = 10.3 (in seawater). The type of pH modifier used, NaOH or Ca(OH)2, had no impact on Cu or Mo recovery, indicating that Ca2+ ions were not involved in any reduction in Mo recovery in the pH range of 9-11. Our results in tap water spiked with either Ca2+ or Mg2+ ions in the same pH range (controlled by NaOH), confirmed that Ca2+ ions had no effect on Cu or Mo recovery, but that addition of Mg2+ ions had a severe adverse effect on Mo recovery at pH = 9.5, and to a lesser extent on Cu recovery. The onset of Mg(OH)2 precipitation occurred at a higher pH, and the adverse impact of Mg(OH)2 on Cu recovery (and perhaps Mo recovery as well) was less, in sea water than in tap water spiked with Mg2+. These effects are attributed to the mitigating role of the high electrolyte concentration, notably NaCl.

Jan 1, 2014

By Wei Sun, Chengwei Li, Zhiyong Gao, Yuehua Hu

"Grinding for mineral liberation is a prerequisite for a successful flotation separation. Different grinding media produce mineral particles with different morphologies and surface properties. In this study, the surface physicochemical properties of fluorite particles produced by ball and rod mills were systematically investigated through single mineral flotation experiment, wettability measurement, X-ray diffraction (XRD) test and scanning electron microscopy (SEM) observations. The XRD observations reveal that the surface exposure degree for both mill particles follows the order {111} > {110} > {100}. The difference lies in that the rod mill ones have a higher exposure of more reactive {110} and {100} surfaces, leading to a stronger interaction with the collector. The difference also leads to their higher elongation and lower roundness values of rod mill particles which are beneficial for the particle-bubble attachment by shorting the induction time. The wettability and flotation results show that the rod mill ones have a lower critical surface tension and a greater hydrophobicity when treated with the collector solution and accordingly perform a higher flotation recovery. This work, for the first time, revealed the importance of the exposure of crystal surfaces in determine the shape factors and reactivity of the mineral particles and will help provide guidance for optimizing flotation separation and particle surface modification. INTRODUCTIONFluorite (CaF2) is the most important source mineral for producing F-based chemicals and materials which are widely used in industrial, environmental, and medical fields [1, 2]. In ore deposit, there are two kinds of occurrence forms of fluorite mineral. Firstly, the fluorite mainly coexisted with the gangue minerals like calcite (CaCO3) and quartz (SiO2). Because of their similar density and fine-grained dissemination in ore deposit, ball mill grinding before flotation separation has been widely applied to produce relatively fine particles [3]. Secondly, the fluorite is often associated with other valuable minerals with higher relative density such as scheelite (CaWO4) and cassiterite (SnO2). Due to their obvious density differences and coarsely grained distribution in ore deposit, rod mill grinding before gravity separation has been usually used to produce more uniform particles and avoid over-grinding [4-6]. After the gravity separation, a flotation separation is also employed to beneficiate the fluorite [7]."

Jan 1, 2018

By V. V. Zakopaylo, M. V. Lukyantseva, V. A. Ignatkina, V. A. Bocharov, L. C. Khachatryan, D. M. Altynamanov, A. A. Kayumov, R. H. Sharipov

"This research was aimed to explain the reasons of low floatability of tennantite from refractory pyrite ores of non-ferrous metals and to create a reagent regime for selective increasing a recovery of copper sulfide minerals from arsenic-containing copper pyrite ore. ?opper-zinc ore of the Uzelga deposit has 89% of pyrite, some part as melnikovite; copper is assayed as 3.58% of tennantite and 0.25% of chalcopyrite; there is 2.19% sphalerite. Sulfide minerals are very finely disseminated. Tennantite is genetically related to primary copper sulfides. Graphene was identified on the surface of tennantite by a transmission electron microscopy (TEM) method. The recovery of tennantite was rose up by using the collector M-TF. M-TF is the mixture of diisobutylditiophosphate (DTF) and O-isopropyl-N-methyl (ethyl) (TC) in the certain ratio. M-TF change up a kinetic of copper sulfide flotation in a slightly alkaline medium, but pyrite has slowly floatability at this moment. A depressing effect of thiosulfate ions in a liquid phase of pulp flotation tennantite from pyrite ore has been established. A copper recovery up 14.2% (from 67.7 to 82.0%) into a copper concentrate level off copper grade of 18.65% (butkx) and 18.68% (M-TF) has been increased by the new technology with M-TF compared to a standard technology with butkx. A main copper recovery up to 50 % in an inter-cycle copper concentrate assaying 19-21% Cu in case of using M-TF was gotten. A zinc concentrate with recovery of 50% and a zinc assay of 41.76% by a standard flow sheet with butyl xanthate was obtained. A zinc recovery of 70.3% with a zinc grade of 44.17% by the M-TF technology was achieved.INTRODUCTION The pyrite copper-zinc ores of the Urals region are considered refractory. The distinctive features of these ores include a high content of pyrite (90-95%), the presence of arsenopyrite and arsenical pyrite, and the simultaneous presence of chalcopyrite, bornite, tennantite with the predominance of the latter (Andreasen et al.,2008;.Dobrotsvetov, 2009; Chanturiya et al. 2016). The flotation properties of tennantite differ from those of chalcopyrite (Xumeng Chen, Yongjun Peng, Dee Bradshaw. 2014), which is the reason why a comprehensive study was under taken of the flotation activity of tennantite and a process for its recovery was developed. The proposed agent treatment and flotation process make it possible to produce salable copper and zinc concentrates."

Jan 1, 2018

By Pengbo Chu, James Finch

Bubbles around 1 mm diameter provide the high interfacial area for capture and transport of hydrophobic particles in flotation. The formation of such fine bubbles is commonly achieved by addition of frothers that appear to simultaneously retard coalescence and promote break-up. High inorganic salt content in process water can substitute for frother. In this work we focus on the action of salt (sodium chloride) on formation of bubbles by break-up. An experimental setup that isolates break-up from coalescence was employed. A pocket of air is exposed to controlled mechanical turbulence to produce single bubbles by the induced deformation of the air and the events imaged. The presence of salt is shown to produce smaller bubbles than in water alone. Comparison with a similar study on frothers is made. The argument is advanced that the presence of frother and salt creates surface tension gradients at the air/water interface which add to the mechanical energy of the deformation and break-up process.

Jan 1, 2014

By T. A. Penzov

As a result of recent scientific and experimental studies new technical devices have been developed for monitoring and control the process of grinding. The description of microprocessor module MILLCONT 1 for control of the loading of the mill and microprocessor density control module DENSIMETER is given in the paper. The improved variant of the automatic system for ore grinding control in single-stage ball mill working in close cycle with a classifier with above mentioned technical means is shown in the paper. The loops for measuring and stabilization of the basic technological parameters (density of the ready pulp ? and fineness of grinding of the pulp ß) are described in the paper. The nowadays economic results in ore grinding process automation are given as well.

Jan 1, 2014

By P. K. Fedotov

At projecting mining-concentrating complex at the deposit ?Zapadnoye? (Russia) it was considered to enable an opportunity of refusal from conventional SAG-mills. First time a scheme of gold bearing ore destruction using Roller Press RP 5-100/90 had been developed and integrated. The plant was launched in summer 2003 and presently it has achieved designed technological parameters, processing throughput comes to 1 million tons of the ore per year.

Jan 1, 2014

By Héctor X. Toro, José Francisco Cabello, Douglas Batista, Álvaro Videla, Claudio Luiz Schneider

The Minas-Rio Project, located in the state of Minas Gerais, Brazil, is currently under construction. The new plant will have a regrinding circuit that uses VertimillTM. The objective is to process itabirite iron ores and it is expected that the consumption of media will represent a large part of the plant operating cost. Many studies in the literature indicate that the size of the grinding media directly influences the grinding efficiency. The size distribution of the charge media is related to the surface area of the charge. In this study, a sample of itabirite iron ore was tested with respect to grindability in a laboratory scale ball mill. The test mill was equipped with a torque device to accurately measure power consumption, as required for the determination of energy specific kinetic parameters. Five tests were carried out with different sizes of steel balls and with SICAM (sub-inch Cast Media). The size distributions of the feed and product of the several grinding tests were used to calibrate population balance model parameters for each condition. The results confirmed that the ball charge with smaller diameter is the most efficient among the different media charge tested.

Jan 1, 2014

By A. Morrison, D. Mesa, P. R. Brito-Parada

"Froth flotation is the most widely used mineral separation technique. It is based on the relative hydrophobicity of valuable and gangue particles. In a flotation tank, two distinct zones can be identified: the pulp and the froth. The pulp is a turbulent region in which hydrophobic valuable particles attach to air bubbles while hydrophilic gangue particles remain in the slurry. As the particle-laden bubbles rise, a mineralised froth zone is formed that overflows as a concentrate. Although the process is more than a hundred years old, there remain many aspects that are not completely understood, particularly for the froth zone. Thus, the rules governing the design of flotation tanks tend to focus on pulp zone parameters, which are largely based on operating data. An example of this is the design and operation of impellers. These tend to be designed paying attention to hydrodynamic phenomena in the pulp zone, but their effect on the froth zone has not been completely addressed. The role of impellers in a flotation tank is to break the air bubbles in order to generate smaller ones and to provide an environment that enables the collision between those bubbles and the particles in the slurry. This usually creates turbulent regimes that can affect the pulp-froth interface, destabilising the lower regions of the froth and affecting the overall performance of the process. Different impeller designs and retrofit modifications have been proposed in the past, addressing some of those issues. However, there is no systematic study of the effect of different impeller designs on the bubble size in the pulp and its links to the stability of the froth. This work tested the impact of an impeller designs combined with the use of a stator on the performance of an 87 litres continuously operated laboratory-scale flotation tank, with a focus on bubble size in the pulp and froth stability. The results showed that the implementation of a stator system decreased bubble size and increased froth stability. That resulted in an increase of mass pull, measured as a proxy of metallurgical recovery."

Jan 1, 2018

By A. Makavetskas

"The purpose of the research is to study the mineralogical features of the structure of the wall accretion formed during melting on the working surface of the walls of metallurgical aggregates and adversely affect the stability of the lining of blast furnaces (BF). We presented the results of studies of the material composition of lining and wall accretion of the furnaces of blast furnaces of the metallurgical plant specializing in the smelting of ferromanganese, nodular and pig iron. It is established that the garnissage is an aggregate of layered texture, formed as a result of the crystallization of slag and metallic melts. Refractory calcium and magnesium silicates and aluminosilicates (minerals of the melilite group, leicite, olivine group minerals) and amorphous glassy oxide solid solutions of variable composition crystallize from the slag melts in the upper part of the hearth. In the slag matrix, inclusions of carbon (amorphous and graphite) and products of crystallization of metallic melts of alpha-iron, iron carbides and / or manganese are observed. Evidence of carbon evolution (in the form of graphite) is precisely in the crystallization of metal melts, there are significant differences in the structure of carbon in coke and in the garnissage. The conducted studies confirm that it is impossible to obtain reliable information on the material composition of new formations in the blast-furnace process without using a complex of modern methods of technological mineralogy.INTRODUCTION The formation of the wall accretion (garnissage) - a solid protective layer as a result of smelting products crystallization on the inner (working) surface of the liner. This is due to the design of blast furnaces with a high-efficiency heat sink using copper coolers and the use of carbon blocks with high thermal conductivity in the lining. The objective of the study was research of the material composition of the lining and wall accretion of the blast furnace hearth of one metallurgical plant that specialized in smelting ferromanganese, nodular and pig iron, to assess the effect of new formations for stability of the lining of blast furnaces (BF)."

Jan 1, 2018

By Nina Panteleeva, Elena Afonina, Stanislav Titkov, Jury Buksha

"Flotation processing of water-soluble minerals (potassium ores, sedimentary salts of salt lakes) is currently the main method for production of potassium fertilizers and concentrated carnallite which is the initial product for production of metallic magnesium. Flotation of sylvite (KCl) and halite (NaCl) is carried out in the electrolyte solutions: KCl-NaCl-H2O and KCl-NaCl-MgCl2-H2O. The report presents the results of studies of the effect of concentration and the electrolyte type on the size of air bubbles in a flotation cell in comparison with the floatability of mineral constituents of potash ores. The floatability in electrolytes of various compositions has been studied: - of sylvite (KCl) by alkylamines, - of halite (NaCl) by alkylmorpholines, - of silicate-carbonate slimes contained in the ore by ethoxylated surfactants. The reagent modes (regimes) activating the flotation desliming of potash ores have been developed."

Jan 1, 2014

By John A. Herbst, Ming Song, Xiangjun Qiu

It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. The study described here shows that these new tools can allow the design of wear part profiles which will maximize mill productivity over the entire life of a liner/lifter system.

Jan 1, 2003

By D. Gucbilmez

Three spiral concentrators having different geometries were compared in a chromite processing plant. They had different diameters, helix-cross sections and capacities. Two of the spiral concentrators were manufactured in China and one of them was manufactured in Australia. The tests were carried out in a closed circuit experimental setup by using a low grade chromite ore. The pulp densities kept the same during the operation, and the samples were taken simultaneously. The effects of the different positions of the splitters on separation and the feed rate were the parameters that were observed during the experiments. The performances of three spiral concentrators were found to be different. To clarify the effect of the particle size on the separation in spiral concentrators, the screening was applied to the feed. The samples were sieved from 75µm. The test results indicated that the separation performance decreased dramatically in very fine particles. Although fine particles caused some problems in spiral concentrators, fine grinding is required for this particular chromite ore for better liberation. A suitable method for the fine particles should be investigated for acceptable recovery.

Sep 1, 2012

By N. Nikolaeva, A. Romashev, T. Aleksandrova

Energetic characteristics identify energy consumption for destruction of prills and kinetic characteristics rate formation of finished size grade in the course of destruction and identify crushing and grinding equipment capacity. And if screen sizing or classification processes are applied in the cycle of ore preparation, then the use of characteristics of separation to size – separating characteristics – is required for theoretical description. Separating characteristics have a lower profile for ore preparation but, nevertheless, they have to be taken into account especially for balance and design calculations of crushing and grinding circuits. In most cases there are impregnations of minerals which vary widely in energy consumption and destruction kinetics and thus polyminerality must be considered as one of priority factor. Raw materials which passed through crushing and grinding processes can be assessed numerically by functions of fractional composition of two types: differential distribution function y ( €) and assay function B( c ) . A set of experiments on grinding of crushed raw materials at different time (up to various sizes) was conducted to analyze effect of grinding size of carbonaceous overburden on function y € and B ( c) as well as to justify the possibility of preconcentration of raw materials at the stage of ore preparation. Analysis of metals distribution per size grades showed that metals are concentrated in size grades of less than 0.315 mm (which is equivalent of cut point for this type of raw material), however, there is no overgrinding and oversludging of material, and enriched product for its further processing can be excluded with the help of classification. The stage of size segregation was tested as a method of preconcentration of raw materials for optimization of ore preparation and further separation.

Jan 1, 2018

By R. Singh

The paper presents the results of characterization and beneficiation studies carried out on a lean grade tungsten ore sample from Degana, India. Basically, three different routes, involving gravity separation, magnetic separation, and froth flotation were studied for concentration of the sample by physical and physico-chemical methods. Considering the low recovery by physical methods, efforts were put in to produce a tungsten concentrate by physical methods suitable for subsequent hydrometallurgical recovery of tungsten as ammonium para-tungstate. This strategy proved quite helpful in minimizing the losses of tungsten in tailings. Based upon these studies a novel integrated technological process flow-sheet was developed for the exploitation of lean grade tungsten ore deposit of Degana, India. Keywords: lean tungsten ore, characterization, beneficiation, gravity and magnetic separation, hydrometallurgical extraction, integrated process route

Sep 1, 2012

By Gulsen Tozsin, Ekrem Kalkan, Taskin Oztas, Elif Agirman Akturk, Ercument Koc, Ali Ihsan Arol

Marble wastes are generated by quarries (marble quarry waste-MQW) and processing plants (marble cutting waste-MCW). The large amount of marble wastes is becoming serious problem for industry and environment because of discarded into rivers and lagoons, without any treatment. Marble wastes can cause environmental problem and economic loss if the waste is not used. However, this type of wastes has a good potential to be used as an amendment for the neutralization of acid soils. In this study, MQW and MCW were applied to an acid soil at different rates and their effectiveness on neutralization was evaluated by a laboratory incubation test. The results showed that soil pH increased from 4.71 to 6.36 and 6.84 by applications of MCW and MQW, respectively. It was suggested that MQW and MCW could be used as soil amendments for the neutralization of acid soils, and thus the negative impact of marble wastes on the environment could be reduced.

Jan 1, 2014

By Zhen Hu, Chenghang Wang, Jianjian Zou, Xiujuan Li, Hanwen Li, Tai Wang, Baoxu Song

A rare earth deposit in Sichuan, China is rich in wulfenite in addition to bastnaesite and barite, and the deposit has already adopted high intensity magnetic separation technique to pre-enrich the rare earth minerals, during which the wulfenite and barite have been left in the non-magnetic product. Because the chemical composition of wulfenite is only 24.17% Mo and 42.15% Pb, it is very hard to obtain qualified lead or molybdenum concentrates by physical separation process. To pre-concentrate the wulfenite, flotation has been first introduced, and by using 100g/t GY-7 as dispersant, 1500g/t CP-1 as depressant and 160g/t GY-4 as collector, a floatation concentrate assaying 15.52% Mo with a recovery of 86.12% was obtained. Then a leaching process was conducted by using 1.2mol/L Na2S as leaching agent, and molybdenum can be translated into sodium molybdate in the solution with a leaching recovery of 99%. To recover rare earth oxides (REO) and lead from the leaching residue, a magnetic separation process has been conducted. Above all, by the whole process, the molybdenum recovery reaches 86.16% in the sodium molybdate solution, and a lead concentrate assaying 54.59% Pb with recovery of 27.99% could be obtained.

Jan 1, 2014

By William Skinner, Jonas Addai-Mensah, Keith Quast, David Robinson, Jason Connor

A review of the laboratory- and pilot plant-scale physical separation techniques for the beneficiation of nickel (Ni) laterites shows limited efficacy. To date, the only upgrade technique adopted commercially, prior to hydrometallurgical processing of Ni laterites, is the removal of a barren, coarse size fraction in the feed by classification. In the present work we investigated two low grade (~ 1%), goethite-rich Ni laterite ores’ upgrading by magnetic separation, attritioning/coarse, (lower Ni-grade) gangue rejection and flotation techniques. Low intensity (0.1T) dry magnetic separation at ambient temperature of raw samples and those pre-heated at temperatures up to 450 °C showed evidence of pay metal Co and Mn bearing asbolane and/or lithiophorite minerals pre-concentration in the magnetic fractions. Ni distribution, however, did not show any noticeable magnetic upgrade but followed the weight distribution. Other ore pre-treatment methods (e.g., desliming and sulphidisation) followed by froth flotation with anionic and cationic reagents also led to noticeable (~35%) Ni upgrade. This is due to the deportment of Ni across several gangue host mineral phases (i.e. Fe oxide/hydroxide and a range of silicate/aluminosilicate minerals). From chemical analysis, after disaggregation of ~ 1% Ni grade feed ore, coarse (-600 + 38 µm) and fine (-38 µm) fractions of ~0.6% and 1.3% Ni grades respectively, were also produced, suggesting that a significant upgrade in Ni content can be achieved by rejecting the + 38 µm fraction with the loss of <40% of the Ni. The ore mineralogy, particularly the complexity and high number of un-liberated Ni-bearing phases, greatly compromises physical separation methods for these ores, with the possible exception of screening after disaggregation of the fines inherent in the run of mine ores.

Jan 1, 2014

By D. Johann, E. Zanetti, I. A. S. Brum, P. M. Zancan, A. F. Castro

"This study was done from a sample of coal mined at the Vale-Mozambique mine, located in Moatize district, Tete Province. The aim of this work is to analyze the reagent system in the flotation of coal fines belonging to the Upper Chipanga layer (UC). Among coal processing methods, flotation stands out as one of the most important for the concentration of this material, in particular in the treatment of fine particles. The total feed of the Vale-Mozambique processing plant is 8,000 tph of coal, where 10% of this feed corresponds to the fine fraction that feeds the flotation circuit. The material used in this study had a particle size of 96% smaller than 0.25 mm. The reagents used in the flotation tests were betacol and diesel oil as hydrophobizing agents and MIBC as frother. The range of betacol concentrations in the first test phase was 200 g/t to 500 g/t, and in the second phase 200g /t to 500g /t while diesel oil and MIBC were kept constant at 300 g/t. The immediate analysis followed the Brazilian standards NBR 8289, NBR 8293, NBR 8290; and NBR 8299. The results showed that it is possible, from a feed with ash content around 22.84%, to obtain products with levels below of 10% ash, with a mass recovery around 50%. The recovery of carbonaceous matter was also evaluated and presented positive results. Complementing this study, the effect of H2O recovery was evaluated and it was observed that for the concentrations of betacol the recoveries ranged from 6 to 9%, and for diesel oil plus MIBC were 4 to 7%.INTRODUCTION Considering the increase in population and energy consumption as humanity has been living along the last decades and the consequent demand for non-renewable natural resources, it is clear the challenge of the mineral industry in the search for new technologies and improvement of the existing ones. This challenge is justified by the need for better industrial results and to meet the market specifications, taking into account the reduction of deposits with higher contents and the need for beneficiation of more complex ores, lower levels and lower release granulometry. Usually in these situations, processes already well-established as the gravimetric (Sampaio and Tavares, 2005) have not good results."

Jan 1, 2018

By Tong Guan, Guangqin Fu, Lihong Deng, Xiaotong Zhou

The raw ore contains many kinds of valuable metal elements. It is rich in valuable metal elements, such as Pb, Zn, Sb, Sn, Ag and is associated with S,Fe,As,In,Cd. A new technology which includes medium intensity magnetic separation, preferential lead flotation, zinc-sulfur bulk flotation, zinc-sulfur flotation separation, tin gravity separation and tin slime flotation was chosen to recover valuable minerals in the raw ore, and the iron concentrate, the lead concentrate, the zinc concentrate, the sulfur concentrate and the tin concentrate can be obtained. To the zinc-sulfur bulk concentrate with the grade of 7.21%Zn and 16.97%As acquired by the zinc-sulfur bulk flotation, two different flowsheets of Zn-S separation technology are chosen to study. The lab test shows that when using lime+DM as depressor, the zinc concentrate assaying 47.73%Zn with the recovery of 95.01% can be obtained and the test indexes are better than that of the flowsheet which using lime as depressor. At the same time, the Cd content is 0.65% and the In content is 0.10% in the zinc concentrate, so they all reach the smelting comprehensive recovery standards and the As content decreases to 0.23%. Finally the flotation separation of christophite and As-bearing sulfide minerals can be successfully realized.

Jan 1, 2014

By Y. S. Sun, P. Gao

"In this investigation, a pilot-scale suspension magnetization roasting reactor was introduced and used to enhance magnetic properties of an iron ore. Consequently, the effects of roasting temperature, reducing gas CO flow rate and fluidizing gas N2 flow rate on the magnetization roasting performance were investigated. The results indicate that the hematite and siderite are almost completely converted into magnetite by a gas mixture of 3.5 Nm3/h CO and 2 Nm3/h N2 at roasting temperature of 520 °C. Under the optimized conditions, the magnetic iron concentrate with an iron grade of 60.18% and iron recovery of 90.17% was achieved. The XRD and Fe mineral phase analyses revealed that most of the hematite and siderite were converted to magnetite, and the magnetic properties were greatly enhanced. INTRODUCTION The steel and iron industry in China has rapidly developed in recent years requiring a large quantity of iron ores. Low-grade and complex iron ores are currently the overwhelmingly dominant mineral resource for iron in China. Therefore, China depends on imported iron ore resources heavily, resulting in an increase in the production costs of iron-making and steel-making[1-3]. Using domestic resources to produce a steady supply of high-quality iron ores is an important step toward the sustainable development of the steel and iron industry[4-5]. The iron ore from Jiuquan iron and steel company is abundant and recognized as typically complex iron ore resources in China. Magnetization roasting followed by low-intensity magnetic separation has been proven as the most feasible methods to upgrade refractory iron ore[6-10]. In present research, an innovative roasting technology, namely suspension magnetization roasting, was developed and applied to recover iron from a typical refractory iron ore. Suspension magnetization roasting technique and equipment developed by Prof. Yuexin Han’s Group at Northeastern University (NEU) is an effective way for the utilization of refractory iron ore. The advent of suspension magnetization roasting will, in China and even globally, produce a significant technological revolution in the field of iron ore beneficiation. Based on the previous works, this paper mainly described experiments on the separation and recovery of iron from a complex refractory iron ore by means of suspension magnetizing roasting and low-intensity magnetic separation processes. The purpose of the research is providing a new technology for effective utilization of refractory iron ore. Process parameters that affected the separation and recovery rate of iron were conducted and optimized, and the reaction process was analyzed by XRD and Fe mineral phase analysis."

Jan 1, 2018