Search Documents

By Xubo Chen, Zhiqiang Hu, Zhijian Sun, Gaoyun Zhou

"The research aimed at developing an efficient and environmental frother,which was applied in the flotation of sulfide ores. The flotation properties of an efficient frother and pine oil have been studied relatively by flotation tests of lead and zinc sulfide ores. At the same time, the biodegradability of two kinds of frother has been studied by the method of biological respiratory curve. The test results show that the flotation properties of new frother are superior to pine oil such as flotation rate, dosage etc. and its biodegradability is superior to pine oil. INTRODUCTION Frother is a kind of important agent in flotation reagents.In practice, the criterion of the foaming performance of the frother is what is high and low according to flotation indexes. The difference of different minerals and flotation technologies has great influence on the foaming performance of frother, and it is very important to choose the corresponding frother. The type, dosage and selectivity of frother in flotation process must be considered carefully. In today's society, environmental protection and ecological protection are becoming more and more important, and the environmental and ecological damage from mine development has aroused increasingly more attention. The use of mine agents has promoted the development of mineral resources, greatly improves the recovering utilization of mineral resources, at the same time, the production and use of mine reagents also inevitably bring about pollution, and result some influence or damage in the ecological environment.The frother is a common kind of reagent in the flotation process of the concentrator. In many cases, the waste water in the concentrator can not be let out in the natural water because the higher content of the frother in the waste water results in higher index of COD.This will inevitably increase the cost of waste water treatment in the mine.Therefore, the choice of frother should not only consider its influence on the flotation index, but also consider its influence on environmental protection. Waste water treatment is a way to solve the waste water pollution, but it needs to cost a lot of fund, manpower and material resources.And the development of high efficiency pollution-free reagent is a good way to reduce the production cost of mining enterprises and reduce the environmental pollution."

Jan 1, 2018

By E. Scheepers

Within a phosphorus producing submerged arc furnace it was found that the continuous fluctuation of the furnace between a flowrate-driven state (high throughput) and a thermodynamic-driven state (low throughput) caused both techniques to have similar overall, predictive abilities and resulted in a linear, ARX-type, adaptive prediction model as the model of choice. Secondly, this pre-diction model was developed, tested and then shown to have a reasonable, 8-hour-ahead predictive accuracy (R2, coefficient of determination) of 30% (±6%) on future Pslag values. This inherent relationship exists because, at the precise moment of a Pslag prediction, the furnace already contains the metallurgical memory (input variables to the linear model) needed to ensure that some predictive possibilities will always exists - all as a result of the long residence times in the furnace. Residence time, however, is not a directly adjustable variable but rather a fully dependent variable and a function of an array of interconnected and interactive variables. In fact, this applies to virtually all input variables, reemphasising the importance of innate metallurgical memory. Thirdly, predictive control possibilities were explored by simulating the set-points of two fully independent variables used by operators to control the process: the ratio of fixed carbon-to-P2O5 and the ratio of silica gravel-to-pellets. This linear, predictive control model showed only a slight improvement with an 8-hour-ahead predictive accuracy of 35% (±7%). This highlights how ineffective current adjustments are in optimally steering the process and how difficult even incremental improvements in feed-forward and predictive control can be. Finally, it is shown that fundamental design-, sampling- and process restrictions currently associated with the process will always limit the predictive and especially control accuracy or meaningfulness of any dynamic model. These restrictions include the size of the furnace resulting in long residence times, 8-hours sampling intervals, an extremely complex and interactive process and a 16% spatial analyses variation on the Pslag values ? the very value that the model is to predict. The point is made that, given the current status quo, even the perfect dynamic prediction model can not improve on an 8-hour-ahead prediction of 30% (±6%). This barrier can only be pierced with e.g. tidier and more frequent sampling regimes and other upfront capital investments, a decision that becomes a cost accounting exercise and that can only be taken by the management structure. An investment demanding ever-increasing attention is CFD software and it?s potential to shed more light on the complex interactions within the furnace.

Jan 1, 2014

By F. H. Wang

The Yinmao Lead-Zinc Mine Co. Ltd. has got 50 years of mining history. In recent years, the manganese grade in the flotation tailings has been continuously increasing. In order to make fuller use of the existing resources, as well as to increase the company?s economic efficiency, our company adopted the technique ?magnetic separation? and ?iron removal? to effectively recycle the manganese concentrate resources.

Jan 1, 2014

By V. E. Vigdergauz

The work presented shows results of electrochemical study of pyrite hydrophobicity evaluated by air bubble induction time (IT) measurements. On the basis of measured IT?s an average thickness of the thin liquid film prior to its rupture has been evaluated, which confirms long-range character of the interactions between air bubbles and hydrophobic surfaces. Obtained data are discussed in the frame of recent studies of structures of solid-liquid interface based on molecular dynamics simulations and results of surface force measurements.

Jan 1, 2014

By Lev O. Filippov, Inna V. Filippova

"Flotation of metal-organic precipitate in column is sensible to the hydrodynamic conditions determined by the diameter and the dispersion of rising bubbles. Thus, the dissipation energy in the system resulting of ratio between superficial fluid velocities (gas and feed) in the column is the main parameter for precipitate flotation in pilot or industrial scales. The suggested limiting factor is the aggregate stability under the turbulence created by the rising bubbles. The stability of precipitate is related to the structural organisation of aggregates, which determines the size distribution of particles during precipitation and flotation stages.Structural evolution of Mo precipitate and the destruction phenomenon were described by using of the various fractal dimensions. The fractal studies allow the detection of a structural scaled organisation of the precipitate flocs. The fractal dimension of the particle mass distribution Dm=1.94+/-0.15 suggests, for the floc structure, a cluster-cluster aggregation process either with restructuring or breakage phases.The destruction process, which occurs for the lowest values of the dissipation energy E (0.02 . 0.05 W/kg) was characterised by a fractal dimension Dg of size distribution. Besides, the destruction of floc produces very fine particles, and thus induces the difficulties of bubble-particle collision during the precipitate flotation in column."

Jan 1, 2003

By T. Wang

A new kind of mixed chelate collector was prepared in order to separate gangue (mainly quartz) and iron minerals efficiently during room temperature. The collector was was composed of two chelate collectors DES and DA. Floatation tests were carried out under 28?C with mixed magnetic concentrates of Donganshan sintering plant, and optimal test conditions were obtained, in which a direct floatation was undertaken and then a close circuit reverse floatation tests ( one roughing, one cleaning, and two scavenging), and a result of Fe grade of siderite concentrate 36.49%, Fe recovery of siderite concentrate 10.65%, Fe grade of final concentrate 66.27%, Fe recovery of final concentrate 78.25%, and Fe grade of tailing 16.22% was gained. Fourier Transform Infrared (FTIR) Spectra and Zeta potential of siderite and quartz adsorbed the DES and DA collectors before and after were measured in order to analyze the reaction between the collector and minerals. Furthermore, Molecule electronegativity of DES and DA was calculated by Electronegativity Proportionality Principle (EPP). Results showed that DES molecules have five active adsorbing sites and their molecule electronegativity was stronger while DA molecules have three active adsorbing sites, which all make the mixed collector has efficiently collecting performance. Zeta potential results of Quartz and siderite showed that at pH 11.5 both kinds of particles charged negative and at this pH value the mixed collector were mainly anionic collectors which indicate that electrostatic adsorption does not exist at this situation. FTIR results showed that characteristic peaks of the mixed collector changed before and after adsorption with the minerals, which means that there exists chemical adsorption or hydrogen bonding.

Jan 1, 2014

By Irena Grigorova, Tashka Ignatova, Ivan Nishkov, Andrian Valchev

"Feldspars used by ceramic and glass industries as fluxing agents are mainly obtained from high quality feldspar deposits. The demand for feldspar as raw material for industrial applications especially in ceramic manufactures is continuously increasing. However, due to the depletion of those deposits, the research activities related to the recovery of feldspar from the lower grade feldspar deposits and feldspar bearing rocks such as pegmatite, granite, arkosic sandstone and syenite have been intensified in the last two decade. In Bulgaria, the main deposit of arkosic sandstone is located in the area of Shumen town, NE Bulgaria. In Srednya deposit arkosic sandstones are found in Upper Cretaceous sediments (Santonian). In this formation, there are two major industrial minerals - feldspar and quartz. They may be of economic value and possibly suitable for commercial uses. The main purpose of the present study was to investigate the beneficiation and upgrading processes of Srednya deposit arkosic sandstones. In a laboratory scale it was studied the possibility to obtain the feldspar concentrate and quartz sand from arkosic sandstones. Particle size distribution, chemical and mineralogical compositions of quartz-feldspar sands were determined. The bench-scale tests using the KOALIN AD laboratory experimental facilities were conducted. Many processing techniques were tested: disintegration, washing, sizing, carbonate flotation and feldspar flotation. The experimental results show that there are possibilities to obtain the silica sand with low content of Fe2O3 - below 0.02 % and potassium feldspar with content of K2O > 14 %. A new technology for recovery of feldspar and silica sand from arkosic sandstone was developed."

Jan 1, 2014

By M. Evertsson, K. Bhadani, E. Hulthén, M. Bengtsson

"Modelling and simulations for mineral processing plants have been successful in replicating and predicting predefined scenarios of an operating plant. However, there is a need to explore and increase the potential of such simulations to make them attractive for users. One of the tools to increase the attractiveness of the simulations is through applying optimization schemes. Optimization schemes, applied on mineral processing simulations, can identify non-intuitive solutions for a given problem. The problem definition itself is subjective in nature and is dependent on the purpose of the operating plant. The scope of this paper is to demonstrate two optimization schemes: Multi-Objective Optimization (MOO) using a Genetic Algorithm (GA) and Multi-Disciplinary Optimization (MDO) using an Individual Discipline Feasible (IDF) approach. A two stage coarse comminution plant is used as a case plant to demonstrate the applicability of the two optimization schemes. The two schemes are compared based on the problem formulations, types of result and computation time. Results show that the two optimization schemes are suitable in generating solutions to a defined problem and both schemes can be used together to produce complementary results. INTRODUCTION The comminution process for a mineral processing plant consists of multiple crushing and classification stages and aims to produce fine material to liberate ore from the minerals. The modelling and simulation of such processes are well established using static process models (King, 2001; Napier-Munn et al., 1996). A recent development in the dynamic modelling for such processes has shown further increase in fidelity compared to the static process models (Asbjörnsson, 2015). The developed simulations can be utilized to design, operate and control mineral processing plants based on the requirements of users (Bhadani et al., 2017). Typically, the requirements in the operation of the comminution process are conflicting in nature, as for instance, reduction of power draw by process units, maximization of production of fine materials, and increasing utilization of the process units. These conflicting requirements leads to a Multi-Objective Optimization (MOO) problem to operate a mineral processing plant. The MOO problems are normally referred to as non-linear problems and its fundamental understanding with respect to process behaviour is difficult to achieve."

Jan 1, 2018

By Megha Patel

"The objective of this project was to investigate the application of Prompt Gamma Neutron Activation Analysis (PGNAA) technology to provide real-time on-belt elemental analysis of feed ore in base metal sulphide processing, in this case at the Mount Isa Mines Zinc-Lead Concentrator Heavy Medium Plant (HMP). After initial exploratory testwork proved successful, a Geoscan On-Belt Elemental Analyser was retrofitted onto the existing HMP feed conveyor. Dynamic calibration of the Geoscan was conducted based on laboratory XRF analysis results of the HMP feed conveyor hammer autosampler samples from May to November 2013. Comparison of the Geoscan results to the laboratory XRF analysis results during and after dynamic calibration indicated the technology had acceptable accuracy to be incorporated into HMP process control. The variation between the two sets of data includes all primary sampling, sample preparation and XRF analysis errors as well as the Geoscan errors themselves. The Geoscan instrument precision must be calculated separately through a duplicate sampling campaign and independent laboratory analysis before extending the scope of its range of application beyond HMP process control. The expected benefits of integrating the Geoscan real-time data into HMP process control are optimised HMP metal recovery, improved cost efficiency and improved stability of the downstream processes (milling and flotation). Utilisation of the Geoscan will also enable improved feedback to mines on grade control and dilution, and provide additional information on individual ore types when fed as campaigns to HMP."

Jan 1, 2014

By S. V. Balikov

A close association of fine gold with pyrite and arsenopyrite is observed at many gold ore deposits. Gold forms and gold distribution in sulfides of different deposits were studied. A comprehensive method including optical spectrum analysis, X-ray diffraction analysis, high-temperature X-ray diffraction analysis, scanning electron microscopy and X-ray microanalysis was used for the de-tailed investigation of the defectiveness of the structure of pyrites from different deposits. It was shown that gold content in pyrites varied from 1.5 g/t to 100 g/t compared with 30 g/t to 230 g/t in arsenopyrites. The nature and arrangement of inner inclusions of foreign minerals in pyrites as well as occurrence of fractures and macro- and microdefects were examined. Iron, sulfur and arsenic contents in all pyrite samples were determined. Chemical composition of the detected inclusions was defined. Parameters of submicroscopic structure of pyrite were estimated using X-ray Fourier line shape analysis. Estimation of real structure characteristics with calculation of submicroscopic D-blocks and root-mean-square lattice deformation 2()evalues was performed. Defectiveness of the pyrite structure can be defined by the following parameters: K?1 and K?2 reflection resolution and its intensity within high Bragg angles; S content to Fe content ratio; the arsenic content and the local variation in its concentration within the pyrite grain; the size of submicroscopic blocks and the crystal lattice disturbance value. The performed analysis showed some relationships between these parameters and refractoriness of the pyrite concentrates. It was observed that at S/Fe ratio close to or higher than stoichiometry and at a low arsenic content (less than one per cent) pyrite concentrates were not refractory. The analysis results showed that concentrates of the Beryozovskaya gold plant (0.02~0.07 As%) and concentrates of the Kommunarovskaya gold plant (less than 0.05 As%) as well as some pyrites from the Sukhoi Log gold deposit had the same characteristics. It was found that average arsenic content did not excess 0.2 per cent. Arsenic distribution within the grain of all these pyrites was uniform. At S/Fe ratio lower than or close to stoichiometry and at high arsenic content (more than one per cent) and significant variation in its distribution within a pyrite grain the pyrite concentrates are refractory. Such pyrites are typical for the Sukhoi Log, the Bakyrchik and the Mardzhanbulak gold deposits. Direct correlation between arsenic and gold contents, in particular, in fine grains of pyrite was observed by many researches. This correlation was explained by impregnation of arsenopyrite which normally contains more gold than arsenic pyrites. The analyses results showed that no arsenopyrite impregnation was found: arsenic distribution within the grain was uniform but its concentration varied greatly. Such pyrite concentrates are more refractory. This paper presents the results of analyses of sulfides to determine the amenability of the associated gold recovery by hydro- and pyrometallurgy.

Jan 1, 2014

By S. Koca

Vast amount of fly ash, bottom ash and slags, are produced each year due to coal combustion in thermal power plants. These products consist of mainly unburned carbon and inorganic compound (such as: silica, alumina, iron oxides, magnesium oxide, phosphorus oxide etc.). These are valuable minerals and can be recycled or recovered if properly processed. One third of the material find application as an ingredient in cement and other construction products, the rest is held in dams or similar dumps, which results in a hazardous impact on the environment, polluting soil and ground water. The unproductive use of land, the associated long term financial burden maintenance and negative environmental impacts have led to realization that alternative uses for combustion by-products as a value added product beyond incorporation in construction materials are needed. At present, there is an intensive search to increase their uses. Other uses of coal combustion residues include as raw material in brick and ceramic tile fabrication, as filler in plastics and paints, extraction of valuable mineral materials, production of zeolites and soil and mine waste treatments. Separation of unburned carbon from bottom ashes by means of flotation was conducted in order to increase the possibility of the recycling of coal combustion wastes. In the flotation experiments collector, dispersant and frother amount, pulp density and pH were tested as variables. After first stage flotation experiments, at optimum conditions, the carbon content was reduced down to 5.58 % in the tailings fraction. This fraction meets the industrial specifications and can be utilized as a cement additive. At the same conditions the carbon content of the concentrate increased to 44.72 % at a carbon recovery of 65.81 %. After the cleaner stage flotation experiment the carbon content of the product is enhanced to 62.53 %. This fraction can be blended back into the coal feed to the power plant boilers.

Jan 1, 2014

By Z. H. Wang

The internal parameters of ball mill are very important in the grinding process and have significant impact on the grinding results. Accurate measurement of the internal parameters of ball mill is crucial and indispensable for optimization and control of grinding process. In this paper, a novel tri-sensor measurement method was used to measure the external signals (i.e., bearing pressure, sound intensity and power consumption) of ball mill. Mathematical models, which link the external signals of ball mill with its internal parameters, were established to predict the internal parameters of ball mill. Experimental results showed that the mathematical models could directly predict the internal parameters of ball mill once the external signals were obtained. The tri-sensor measurement method and the mathematical models proposed in this paper provided a new way and solid basis for optimization and control of ball milling.

Jan 1, 2014

By A. Kurkov

Flotation process is based on the formation of primary collector-based supramolecular associates at the mineral surface and within the pulp. Supra molecular chemistry allows studying within a common framework, all kinds of molecular associates, from dimers to large assemblies, resulting from spontaneous association of a large number of interacting components of the flotation system, where the collective action of non covalent bonds can have an important role. Self-organization of supra molecular assemblies in the flotation process can be controlled by modifying the chemical structure of the collector, the nature and arrangement of functional group in it, by introducing secondary agents (SA) into the process, to adjust the interaction between the collector and the surface and to control the hydrophobicity of the adsorption bed. This offers broad opportunities to build supramolecular assemblies to improve the efficiency of flotation. Besides, the more complex is the system, the weaker are the interactions, that determine its behavior. This powerful factor still is not employed deliberately to control the flotation process. Organophosphorus compounds (OPC) - dialkyl phosphoric acids whose radicals contain ethoxylated groups ? are considered as nanocompounds, that can be used in building supramolecular assemblies. The presence in an OPC molecule of functional groups (P=O, P (O) O-, P (O) OH), ethoxylated groups, and aromatic rings is the basis for the formation of stable supramolecular associates. Gross formula: C54H94KO16P. Molecular weight is 1069.39. Phosphoryl anion has a regular tetrahedral structure with the angle of 109.5°. Lengths of -P-O- bonds in a PN molecule are 1.7345Å; length of the hydrocarbonic radical C42-C72 = 33.942Å. In an alkaline environment, PN is in the form of the anion, in an acidic environment ? in the form of the polycation due to protonation of the oxygen in the EO group. Chem Office software suite was used to generate three-dimensional images of an OPC molecule in acidic and alkaline environments, to reveal the OPC geometry (bond lengths, valence angles, aliphatic radical length), to identify the collector's binding sites with the mineral surface, to find the most stable and energy-efficient molecular conformations of an OPC molecule and its complexes with minerals under various conditions. Mechanisms of interaction between OPCs and the mineral surfaces are different. In ores whose minerals are dominated by ionic bonds (fluorite), the interaction mainly involves the anionic form of the collector; in ores, whose minerals are dominated by covalent bonds - the oxygen of the phosphoryl group (donor-acceptor interaction) and the oxygen of the ethoxylated groups. This difference is responsible for the formation of spatial associates with different surface layer structures. Introduction of supramolecular chemistry concepts into the analysis of flotation phenomena and mechanisms can become an effective tool for better understanding the flotation process and offers new means of consistently improving its effectiveness.

Sep 1, 2012

By M. A. Hampton

The surface oxidation of sulfide minerals in aqueous solutions is an important sub-process in sulfide flotation and hydrometallurgy, but a full understanding of the oxidation process and products is still lacking. Many oxidation pathways and products involving elemental sulfur, metal polysulfide, metal-deficient sulfide and sulfate have been proposed, confirmed and argued. In this paper we provide further insight into the surface electrochemical behaviour of galena in aqueous solutions. For this research we have developed a novel experimental system, that combines chronoamperometry and AC-mode AFM surface imaging, which allows for in-situ, synchronized electrochemical control and examination of oxidative surface morphology. At pH4, the morphology of elemental sulfur (detected by ex-situ Cryo-XPS) formed on the oxidizing galena surface depends on the electrochemical potential pathway. In multi-step chronoamperometry (i.e. four potential steps from 0 mV to + 350 mV) the sulfur forms as nanoscopic domains, whereas in single-step chronoamperometry (i.e. one potential step from 0 mV to + 350 mV) sulfur forms as a heterogeneous layer. In each case the oxidation is controlled so that the number of electrons (coulombs) passed per unit area is the same, therefore the amount of sulfur produced is also the same. The differences in morphology with electrochemical potential pathway are explained using a nucleation and growth model. The formation of sulfur on the surface increased both advancing and receding contact angle of galena, but the morphological changes induced by different electrochemical potential pathways did not significantly alter the hydrophobicity of the surface. Keywords: galena, lead sulfide, oxidation, Atomic Force Microscopy, electrochemistry, collectorless flotation, hydrophobic

Sep 1, 2012

By Shobhana Dey

A low volatile medium coking coal from Jharia coal field, India was used for this investigation. The proximate analysis of the sample shows that it contains about 25% ash, 21.4% volatile matter and 52.4% fixed carbon. The sizewise ash analysis of -0.5 mm coal indicates that -0.5+0.15 mm fraction contains lower ash (21.9%) than -0.15 mm fraction (29.7%). The flotation characteristics of the -0.5 mm coal were determined by release analysis. The study reveals that recovery of combustible at 15% ash is about 27% and 43% at 17% ash level. The low recovery is due to the presence of high ash in finer fraction. In order to improve the recovery, the -0.5 mm feed was classified into -0.5+0.15 mm and -0.15 mm fractions, and subjected to flotation separately. The recoverable combustible obtained from the release analysis of -0.5+0.15 mm at 15% ash level is 46%. The effect of collector dosage, frother dosage and aeration rate on flotation was studied. The responses of these variables in collectorless flotation of the -0.5+0.15 mm fraction containing low ash were also studied. A lower aeration and frother dosage favored the generation of clean coal with low ash. The ash content in the tailing stream from -0.5+0.15 mm flotation circuit is close to that of the original -0.15 mm fraction. The former is ground to -0.15 mm and the two fractions are processed together. As -0.15 mm fraction contains relatively higher ash, collector aided flotation using sodium silicate was performed to recover the clean coal with 17% ash. The products of the overall flotation circuit having different ash levels were recommended for use in different applications. The reject from -0.15 mm flotation circuit contained 56.4% ash which can be used for fluidized bed combustion (FBC). This eventually leads to complete utilization of coal.

Sep 1, 2012

By M. Tang

The phosphate ore sample was taken from the iron tailings after recovering most of magnetite by magnetic separation in Longlin, Yunnan Province of China. Batch flotation tests had been conducted to upgrade the phosphate concentrate by conventional fatty acids reagents under 70% -75 µm of the particle size; however, the unsatisfied results (P2O5 grade of 27.84% and recovery of 49.25%) were obtained. Also there are a large amount of slimes trapped in the concentrate and high-dosages consumption of reagents, for example, more than15 kg/t soda ash and 2 kg/t sodium silicate at only one-staged roughing. Based on the analysis of X-ray diffraction (XRD) for the sample, most of gangues are clay, quartz, and chlorite, which may easy to over-grind and deteriorate the flotation process either on reagents consumption or slurry fluidity or viscosity. A hydro-cyclone had been introduced to pre-concentrate the phosphate ore by scrubbing the slime before flotation, which can result obviously in reducing the dosages of soda ash from 15 Kg/t to 4 Kg/t, and raising the grade of P2O5 in the concentrate from 27.84% to 36.13% at the expense of about 4% recovery of P2O5. They also substantially reduced the time of sedimentation of concentrate after flotation from ~10 to ~1 min. In this paper, the effects on the recovery of P2O5 by the different dosages of flotation reagents with or without de-sliming were studied, with the objective of determining the different effects on the functions of flotation reagents by slime during flotation. Keywords: de-sliming, phosphate, soda ash, flotation

Sep 1, 2012

By C. Han

The analytical results of Dagushan grinding workshop primary grinding operation product show that the size fraction of -0.079mm is 32.88%, the size fraction of -0.01mm is 9.97%, the rate of -0.01mm size fraction and -0.079mm size fraction is 30.32%. It means that there is too much -0.01mm size fraction in primary grinding operation product and fall out that there will not be a better result in following operations. Several tests have been carried out to control the size distributing of the primary grinding operation product according to confirm the appropriate conditions of grinding operation. Integrate with theoretic count, grinding property tests show that the appropriate rev ratio of ball mill should be between 85% and 90% so as to get better size distributing. Based on the results of grinding property tests, the shocking property tests simulated the momentum of different diameter steel balls in the ball mill have been carried out. It showed that if want to get better size distributing the appropriate diameter of steel ball should be 110mm. The tests result shows that regulate diameter of steel ball and rev ratio of ball mill could control the size distributing. Contrast to the technical parameters of ball mill in grinding operation now, there are some significant advices are given for practice and industrial tests.

Jan 1, 2014

By H. Z. Liu

An extra-refractory gold ore in China belongs to Carlin Type Gold Ore which is not only submicroscopic but also rich in arsenic and organic carbon. They have been proved that its floatability is not good enough and the gold in the ore could not be leached almost if it was not pretreated. The tests for the ore were carried out in accordance with flotation-concentrate preoxidation-cyanidation(or CIL) processes in order to exploit the mine. Two new depressants were discovered in the flotation tests and improved concentrate grades from about 20g/t to 32~50g/t. The methods of the concentrate preoxidation tests were alkaline atmospheric oxidation, acidic atmospheric oxidation, acidic pressure oxidation, roasting oxidation?biooxidation. The cyanidation tests after the concentrate preoxidation have proved the gold extraction of the pressure oxidation to be the highest(92.5%) and that of roasting secondary(89.3%). After fuller techno-economic comparison, it is suggested that the flotation-pressure oxidation or roasting-CIL process should be the most optimal for treating the ore. The gold recoveries of the ore were 83% for the pressure oxidation and 80% for the roasting respectively.

Jan 1, 2014

By Indresan Govender

A continuum based granular flow model of charge motion that combines the inherent frictional nature of particles with its distinctly fluid-like structure is presented. Starting with Newton?s 2nd Law on a volume element of charge, we derive the velocity field in the bed free-surface and the rising en-masse region. Invoking flux conservation within the two regimes of interest then yields a (simple) differential equation for the free-surface of the charge body. Combining the velocity field gradients with a suitable constitutive choice for the shear stress completes the picture with a description of the in-situ rate of shear power dissipation in a tumbling mill ? a mechanistically correct account of power draw in a tumbling mill. Positron Emission Particle Tracking (PEPT) was used to measure the in-situ flow fields of the charge within opaque systems like tumbling mills. The accurate velocity and mass distribution derived from PEPT form the basis for direct verification of the resulting granular flow models. In this regard a wide range of milling conditions is investigated and presented in this paper.

Sep 1, 2012

By Marianella Perez, Williams Calderón, Gonzalo Montes-Atenas

The lack of fresh water sources, particularly in the Northern part of Chile, has driven the mine sites to search for new and sustainable paths to obtain water resources to run minerals processing operations. Among them, the use of seawater in concentrators appears as an interesting solution to this problem. However, the presence of seawater will have an impact onto the operation, not only because it will enhance corrosion reactions in the equipment installed in a plant, but also because it may affect how particles will effectively be processed across the numerous unit operations existing in the mine site. Among such unit operations, the grinding stage is a highly regarded as it defines the success of the separation of valuable minerals from gangue material in the froth flotation operation. Then, one important aspect to be addressed is to understand how the presence of seawater will affect the different mechanisms acting during the operation of a ball mill. The aim of this research work is to assess the effect of changing the aqueous matrix from process water to seawater in ball mills onto the mill performance. The methodology considered the use of Fluent® software and its capabilities to run numerical simulations with heterogeneous media. On one hand, from the data analysis, it is possible to infer that breakability mechanisms should not be significantly affected. On the other hand, the high ionic strength of the matrix should impact importantly particle transport mechanisms within the mill. Particularly, when transporting finer particles. Rheology results were in agreement with previous published research studies suggesting the suspensions to behave as Newtonian, Dilatant o Pseudo-plastic fluid depending on the amount of fine particles present in the grinding media. The latter will result in changes in the residence time of particles in the mill producing overgrinding or an excess in the circulating loads.

Jan 1, 2014