Search Documents

By George J. Tamara

The urban environment presents special challenges for the design and construction of earth retention systems. Complications arising from difficult subsurface conditions are compounded by the presence of urban infrastructure and existing and prior construction. The proximity of adjacent structures as well as intense prior use can cause special concerns including the potential for archeological artifacts or contaminated ground or ground water. Utilities and structures may be particularly vulnerable to the effects of ground movement, dewatering and vibrations. Difficulty of access, congestion and limited work areas may severely restrict means and methods of construction. Dewatering may be limited or prohibited because of concerns for disposal of clean or contaminated water, depletion of aquifers, drawing of contaminants to the site or dewatering induced settlements.

Jan 1, 2003

By Emöke Imre

A point-symmetrical linear coupled consolidation model with displacement boundary condition is suggested for the description of the consolidation around the pile tip after pile penetration. Analytical solution is given. Main features of the solutions are predicted by the analysis of the system of differential equations and, the boundary conditions.

Jan 1, 2002

By Frank Rausche

Since the early 1980s, when the Road Construction Authority of Victoria authorized the dynamic proof testing of roughly 100 drilled shafts of 1.5 m diameter and typically 60 m length in Melbourne Australia, dynamic load testing has been applied worldwide for quality control of drilled shafts. Today, test capacities of 4000 tons or more are not unusual. On numerous occasions the authors have been involved in similar tests in the United States and test engineers from other countries have reported on experiences in many different countries. Without doubt, generating high test loads is most economically accomplished by dynamic load testing and this method is particularly well suited for testing piles founded in rock because of the rocks low energy dissipation. However, deep foundation professionals have on occasion expressed reservations about subjecting a drilled shaft to impact loadings fearing, for example, a degradation of the shaft ? rock interface properties or potential error sources due to uncertain concrete properties or shaft geometry. This paper will present numerous case studies, demonstrating the performance of rock socketed drilled shafts under dynamic loads. It will discuss the mechanics of the dynamic tests and the method of data interpretation, addressing the concerns stated above and investigating the limitations of the test method. The paper will formulate a set of recommendations for the design and execution of these tests.

Jan 1, 2006

By Carl-John Grävare

This paper deals with some of the systems and equipment that are being developed and/or are in use in Scandinavia. The main subject is the development of loading tests on the piles using monitoring equipment. This paper also describes ground improvement using lime-cement columns, expander body piles and steel core piles.

Jan 1, 2000

By Tom A. Armour

Different variations of soil nailing techniques have been used in the United States since the late 1970's. Such techniques owe their origins to French developments, which began in the early 1970's as a spin-off from European tunneling excavation support practice. The growing demands of urban infrastructure development and rehabilitation and environmental protection have created an active and expanding soil nailing market demand for earth retention and slope stabilization in the United States since its early developmental years. There is a clear need for a fundamental review of the large number of soil nailing techniques that are currently being used in the United States. Following a brief summary tracing the historical development of soil nailing and a generic classification of applications, this paper provides a review of the different recent advances in the design and construction of soil nailed systems. Discussion topics include nail design advances, permanent "top-down", structure support/underpinning, alternative face stability measures, composite systems, hollow bar and fiberglass nails and architectural reinforced concrete/shotcrete facings. Case histories will be presented to illustrate each of these advances.

Jan 1, 2003

By Niels Krebs Ovesen

Close economic cooperation was established among the countries in western Europe during the seventies. As a consequence, among others, a need for harmonized technical specifications for civil engineering works arose. Technical specifications for design and execution of building and civil engineering structures exist in most of the European countries. In some countries such technical specifications are part of the building regulations and in other they are independent codes of practice and standards. The works on the Eurocodes was initiated by the Commission of the European Communities about 1976. The Eurocodes are intended as common unified design codes for different load bearing structures constructed from different materials. They are also intended to cover design of geotechnical structures. They are established with a view to promote the free movement of goods and services within the member states of the European Community - the so called Internal Market - and within the member countries of the European Free Trade Association, EFTA by removing obstacles arising from different rules for calculation and design.

Jan 1, 1994

By Peter White

A bridge reconstruction project involved driving pipe piles for the new foundations. Disturbances within soil layers at depth caused sinkholes to open up within the construction site. After a near fatal accident, the pile driving installations were suspended. The solution involved ground im­provement through cement grouting with sleeve pipes and special grout additives to minimize migration of cement grout.

Jan 1, 1997

By Geoffrey D. Collins

This paper deals with the construction of the Effluent Outfall Diffusers which form part of the outfall for the Deer Island sewage project. The work was executed 15 km out to sea in Massachusetts Bay and required the drilling, installation, grouting and accurate determination of the actual position of 55 riser shafts in 33.5 m deep water. Although not strictly a "foundation", the contractor's approach to the installation of the diffusers was a logical development from many marine foundation projects executed by the Contracting companies over the last decades. The only previous application of this design of outfall had been in Australia where offshore oil drilling techniques had been adapted for use in riser installation.

Jan 1, 1994

By Ali Porbaha

The use of soil nailing technology as a cost effective alternative for excavation support and slope stabilization has substantially increased in the United States during the last decade. For example, in the past thirteen years, more than 185,800 square meters of soil nail walls have been constructed in California alone. The conventional soil nail systems pose difficulties when ground conditions are subject to caving, for instance for silty sand (sugar sand) or cobbles and boulders. The construction industry has developed self drilling hollow bar systems (or pressure injected bored, IBO) that combine both drilling, placing and grouting in a single operation as a solution to speed up construction. While the system is extensively used for temporary applications, nevertheless, some concerns, particularly about corrosion, has limited the use of this technology as a permanent system in North America. This study presents several issues related to self drilling soil nail systems, the results of a field investigation and a summary of the research project.

Jan 1, 2006

By Garth Howlett

In 1998 the Matanuska-Susitna Borough formed the new port district at Point MacKenzie, known as Port MacKenzie, located directly across the Knik Arm from Anchorage. In 1991 PND Engineers Inc. (PND), working with the Matanuska-Susitna Borough manager and port director, envisioned a fill structure at Port MacKenzie with a 500-foot-long Open Cell? sheet-pile bulkhead face extending to EL -20 feet Mean Lower Low Water (MLLW) at the face. Now under operation the fill created 5.5 acres of tideland property using local materials for fill. The fill is protected from 2- to-3 foot-thick ice pans and 9 feet per second (fps) tidal currents by an envelope of armor rock. Construction required working in water with 30 to 40 feet of tidal variation. Construction required placement of frozen fill in water depths possibly exceeding 50 feet, creating real concerns about soil consolidation and long-term maintenance issues. A plan was prepared to consolidate the soils using Vibracompaction. Soil Density and consolidation were monitored during the work. In 2003 the port district and NPI, a wood chip export company, formalized an agreement to construct a deep water port facility at Port MacKenzie for cape-class bulk carriers. PND provided planning, studies, geotechnical investigation, design documents and construction inspection for a 500-foot-long trestle with a platform dockhead and dolphins providing 1,100 feet of dock face in EL -70 MLLW as shown in Figure 1. Design included installation of large-diameter spin-fin piles driven on a 2V:1H batter. Also included was a 300-ton tension test of smaller spin-fin piles.

Jan 1, 2006

By Michael J. Atwood

Many buildings in Boston are founded on untreated wood piles, which can deteriorate and lose their structural capacity if groundwater levels are lowered below the tops of the piles, exposing the wood to air in the unsaturated soils that surround the piles. The problem of wood pile deterioration due to lowered groundwater levels in Boston first became evident in 1929 following discovery of rotten piles beneath walls of the Boston Public Library building. Repairs to reconstruct the library building?s wood pile foundations were made in 1930 using pit underpinning methods. Today, more than 80 years later, the subsurface conditions beneath several of Boston?s historic neighborhood areas continue to be plagued with low groundwater levels - regrettably resulting in ongoing deterioration to the wood piles that support some of Boston?s oldest and most beautiful buildings. Pit underpinning is still recognized as the preferred approach to repair wood piles and restore uniform foundation support beneath the impacted buildings. This paper provides a brief historical review of the land filling in Boston through the early 1900s that led to the use of wood piles as building foundations. Also discussed is the impact that groundwater level can have on the long term performance of wood pile foundations and the pit underpinning procedures used to reconstruct decayed wood pile foundations in 1930 beneath the Boston Public Library, and today beneath some of Boston?s oldest buildings. Also included are discussions on engineering controls and permitting requirements that help ensure safety and protection to the workers and buildings during underpinning, and some procedures being used to supplement and improve the loading capacity of the reconstructed foundations and facilitate construction of new useable below-grade space.

Jan 1, 2011

By S. Narasimha Rao

Bored cast in situ piles are highly susceptible to construction defects like necking, discontinuity in concreting, poor compaction of concrete, improper end bearing condition due to inadequate cleaning of bore hole, exposure of reinforcement, segregation of concrete etc. There is a necessity to understand the behavior of piles so as to design effective foundation system. In this paper investigations of two field cases were discussed to bring out the effect of defective piles. In one case improper end bearing has been discussed for a concrete pile of length of 45m and diameter equal to 1.2 m and is reinforced with 32 no's of 28mm diameter steel bars and in another case necking of the pile has been discussed. Further model piles with preformed defects have been tested in laboratory to bring out the influence of defective piles.

Jan 1, 1996

By Martin J. Kenwright

Within the famous Harrods department store, a new lift shaft has been constructed, servicing a depth of 22m below ground level as well as the existing 6 storeys of the store. The shaft will connect with a new goods tunnel which is to be excavated beneath the shop, as well as new floor space above ground level which has resulted from the infilling of a previously existing lightwell within the store. The construction of the deep shaft while maintaining uninterrupted use of the store by the Client led to a number of innovative solutions being undertaken. Empirical assessments were made of settlements anticipated from the construction process, which took place within a congested environment of existing foundations. Various elements were designed and installed to mitigate the effects of the inevitable ground movement on the surrounding overlying structure, which supported sensitive high quality finishes and mechanical and electrical installations. The reinforced concrete lining of the shaft was contained within a cofferdam of minipiles. The minipile placement accuracy (1 in 150) was vital as it could not interfere with the subsequent tunnelling works. As the scheme progressed this became even more critical since the minipiles were needed as support for parts of the permanent works. This paper describes:- the high quality placement and control of the minipiled cofferdam, the methods employed in assessing ground movements and the techniques used to mitigate against the effects of these movements.

Jan 1, 2000

By William S. Gardner

It is certainly an honor to have been invited to address the Deep Foundation's Annual Meeting on such a vast and weighty topic as "Present to Future Design Considerations of Deep Foundations." Acknowledging the enormity of this 30-minute assignment, I hope to at least scratch the surface of the topic deep enough to generate some thought and reflection. Design considerations, be they current or future, bring to mind a number of important subtopics which comprise the design process. As shown by Figure 1, a flow chart of this process describes, in general terms, the sequence of a deep foundation design.

Jan 1, 1991

By Clyde N. Baker

Foundations for the Sohio Corporate Headquarters in downtown Cleveland have column loads of 11,400 kips, which increase to 15,000 kips with wind loading. An extensive exploratory program was conducted and comprehensive studies made to select the economically dependable support for the 46-story structure. A test on bond or socket friction for the caissons has usable values.

Jan 1, 1984

By Robert G. Lenz

Control of ground water for construction purposes is an everyday occurrence in the U.S. Thousands of pumps are in service at any given time. Most of these applications simply consist of pumping water out of an excavation, generally with the aid of sumps. Modern hydraulic and electric submersible pumps permit these procedures because of their ability to pump solids and take air without losing their prime. These procedures work fine up to a point and permit the contractor to control his ground water problems adequately and at minimal cost. When that point is exceeded, the ground water problems sometimes are compounded. Over-application of open pumping techniques can result in slope failures, cofferdam instability, bottom heaving, boils, loss of ground, damage to adjacent structures and utilities, and assorted other maladys which could and should be avoided. This paper will deal with the options involved in ground water control, a discussion of the unwanted side effects of dewatering, and examples of ground water control projects in various cities around the U.S.

Jan 1, 1988

By A. F. Deng

A general description of the project, mainly the pier foundation design of the ZHU JIANG FANYING is presented in the paper. The major contents include the foundation scheme, the evaluation of bed-rock characteristics, the allowable bearing pressure, the design and construction of pier foundation.

Jan 1, 2010

By G. G. Goble

Significant progress has been made in the past decade in determining the load bearing capacity of pile foundations. Developments in the means of prediction of pile capacity as limited by soil strength have been substantial, particularly in the use of dynamic methods. The use of currently available equipment, analytical procedures, and practices in the field, will often produce material economies on a job by allowing increased loads with proven factors of safety. This approach justifies the minimum number of piles required for a safe foundation in a wide range of job sizes and soil conditions. To avoid exposing the reader to excessive detail in the body of this paper, technical topics have been covered more thoroughly in several appendices. I. Wave Equation Analysis of Piles Appendix A II. Dynamic Monitoring and the Pile Driving Analyzer Appendix B III. Case Method Capacity Calculation Appendix C IV. Case Pile Wave Analysis Program Appendix D 1 Preliminary Analysis In designing driven pile foundations, there must be a close relationship between design, construction control procedures, driving practices, and the size of the job. Small commercial buildings or residences involving loads that are only a fraction of the pile capacities do not justify the expense of detailed design processes or elaborate construction controls. Nevertheless, some preliminary analysis of the job requirements and a limited subsurface investigation must be made to understand existing conditions and the possible foundation solutions. In other words, it is necessary to determine that driven piling is the best overall choice of foundation.

Jan 1, 1988

By Chen Xizhe

The caisson is adapted to the foundation of concentrated heavy building. As there are the flowing sand, boulder or cobble and other serious obstruction, the open caisson can't sink, the caisson can solve these problems easily. Especially for the stability of the neighour building, the merit of the caisson is outstanding. Therefore, there are the pier, the foundation of heavy instrument and the large water pumping station etc. using the caisson in China. This paper introduce several caissons and successful experience by author's investigation. It contains the feature and application of the caisson : the examples of caissons such as a huge pier of a bridge acrossing a big river, a large instrument foundation and a large water pump station beside a river; the problem of the design of the caisson and notice items during the caisson construction etc.

Jan 1, 1991

By Graeme McWhirter

This paper discusses the Installation of a Vibwall for the Cardiff Bay Barrage Project Wales, UK, by Kvaerner Cementation Foundations. Only the second use of the technique in the UK the wall was successfully placed to a depth in excess of 20 metres, in unique and challenging conditions. The installation of the Vibwall was a technical success, but not a financial one. The use of the technique was at its "limits" and this paper recommends some of the controls essential in the carrying out of such work in the future.

Jan 1, 2000