Search Documents

By Alexander Nikolic

The paper presents the foundation design and construction of a landmark urban redevelopment scheme in central London, UK. The scheme comprises the new Tottenham Court Road Underground station, Crossrail interchange box and associated over-site commercial development. The paper focuses on the design, procurement and construction of large diameter bored piles, up to 68m in depth, which form the foundation support system for the over-site commercial development at Denmark Place. The congestion below ground required an intricate foundation design solution which has been a catalyst for developing innovative load transfer arrangements and has resulted in the advancement of pile construction technology in the UK. The foundation system was also designed to cater for the construction of two significant elements of proposed below ground infrastructure. Selected large diameter piles have been constructed within 1.1m of live underground railway tunnels. An innovative D-shaped pile was constructed in a zone subject to particular spatial constraints. The proposed Crossrail tunnels will be bored within 1m of selected over-site development piles. In addition, a 30m deep excavation forming a new escalator box will be constructed in direct contact with the over-site development piles. The stakeholder engagement process is described together with the foundation design development and buildability assessment. The benefits from early collaboration between the designers and specialist contractors are highlighted. From an analytical design perspective, the entire foundation construction sequence was modelled in detail in order to assess the soil structure interaction and any potential adverse effects on existing elements of underground infrastructure. The results from the three dimensional numerical modelling simulation are compared with field monitoring data.

Jan 1, 2011

By Lawrence P. Goldfarb

The City of Alexandria, Virginia, Public Safety Center (PSC) is a 64,000 square foot facility that houses the Police Department, Office of Sheriff and the Office of Magistrate. In addition, the center includes a detention facility for local and federal inmates, operated by the Sheriff. The PSC is composed of a 3-story building to the west and a 6-story building to the east constructed on a landfill in a wetland area in the flood plains of hunting Creek. The existing ground floor of the 3-story building is a floating slab-on-grade, with the interior and exterior columns, exterior walls and upper floors all supported on belled, drilled shafts. Portions of the floating first floor slab have undergone excessive settlement due to the apparent consolidation of the underlying organic soils. The magnitude of the settlements of the floating first floor slab is sufficient to require replacement of the slab and relocation of a portion of the facility. The rehabilitation was complex and required staged construction, consisting of constructing Auger Pressure Grouted (APG) Piles in low overhead conditions. This paper summarizes the geotechnical conditions that lead to the excessive settlement of the floor slab, the construction of the (APG) Pile foundations in low overhead conditions and the evaluation of potential future settlements.

Jan 1, 2009

By Rob Jameson

"The demand for commercial and residential construction has continued to evolve across the United States over the last decade. Our markets demand larger, deeper and inherently more complex structures, located within increasingly constrained urban locations and with challenging geotechnical conditions. As project demands incrementally escalate, specialty contractors are continuously challenged to extend their state of practice. Development in the size and capabilities of construction equipment, tooling, techniques, monitoring and verification systems over the last decade has consistently allowed contractors to build larger and deeper. For support of excavation (SOE), in addition to scale, selection of the most appropriate system has been a key to success in the most challenging ground conditions. This selection process is based on sound engineering and construction practice, and also prior experience, both positive and negative. Ultimately many Owners have chosen to manage their risk of SOE construction through design-build contracts, which allows specialty constructors to optimize the balance of cost, schedule, scope and associated risk based on their local expertise. Successful implementation of a design-build methodology begins long before a contractor is selected, with identification of key project requirements and risk factors during the feasibility studies and design development phases. In these early stages of the project development, advice and budgets are frequently solicited from Specialty Contractors. The Owner, Construction Manager and Consulting Team will filter this input from multiple sources to provide their specific recommendations, develop construction documents and select the appropriate form of contracting. Only in the final stages, after award of a Design-Build Subcontract, can the successful specialty contractor directly influence risk management approach on the project. A case study is presented from Block 9 in San Francisco’s Transbay District. This project demonstrates the incremental identification, assignment and mitigation of construction risk through the planning and design build process for SOE on the deepest planned excavation in San Francisco.INTRODUCTIONThe mature urban development market in United States results in high demand for complex Support of Excavation (SOE) schemes on constrained sites. The Design-Build approach can be applied to increasingly difficult SOE challenges, combining regional specialty subcontractor knowledge and experience in order to optimize solutions for cost and schedule. The most successful applications will involve early engagement of shoring subcontractors within the project teams, during feasibility and design development stages, in order to identify key scope and risk issues, and their potential solutions. Throughout the project development, it is important to reasonably assign responsibility for construction risks amongst the project stakeholders who are best able to control them.This paper presents a case history for San Francisco’s Block 9, a well-planned and successfully executed design-build SOE project in San Francisco’s Transbay Redevelopment area. Throughout the 4 year period from the Developers initial proposal to the Redevelopment agency, through completion of excavation down to subgrade, the project team developed a series of increasingly refined SOE schemes, with corresponding scope definition and cost and schedule estimates. This program relied on early identification of key challenges and risks for the project, and evolved through multiple phases of proposals as first the General Contractor (GC) and then Specialty Shoring Subcontractor were engaged for the project. The scheme, cost and schedule refinements continued throughout construction in order to accommodate unanticipated conditions and events as they unfolded."

Jan 1, 2017

By Liang Shen

The Cooper River Bridge, the longest cable-stayed bridge in North America, replaces two existing bridges along U.S. Highway 17 and connects the City of Charleston and the town of Mount Pleasant, South Carolina. Two diamond shaped towers support the 1,546 ft long main span over Cooper River and allows for a 1000 ft wide navigation channel. The Charleston high-level approach is 4351 ft long and provides a 250 ft wide navigation channel for Town Creek, while the Mount Pleasant high-level approach is 2,090 ft long. Due to the high seismicity in the region, potential vessel impact, and hurricanes, large lateral loads are expected. From various types of foundations, 10-foot diameter drilled shafts were selected for their high capacity against vertical and lateral loadings. The shafts are founded on a stiff to very stiff lightly cemented calcareous sandy clay or sandy silt layer, called Cooper Marl, which underlies the coastal sediments of the interbedded clays and sands. A group of 11 shafts supports each main tower, while a rock island protects it from vessel collision. A group of 4 to 8 shafts foundations support the other piers of the main span unit. A pair of shafts supports the High Level Approach piers. The shaft tip elevations vary from 120 ft to 230 ft below water line. An elaborate geotechnical investigation was conducted on the site, including a load test program on full-scale shafts under axial and lateral loads. The results of the tests were used to calibrate the lateral and axial soil resistance. The objective of this paper is to present the different aspects of the bridge foundation design.

Jan 1, 2013

By H. Meseck

The new building of the Central Bank of Iraq in Baghdad was footed in difficult underground conditions on more than 600 reinforced concrete driven piles, with cross-sectional diameters of 45 x 45 cm and pile lengths of 12.0 to 18.0 m. The necessary embedded depth and the bearing capacity thus reached were established on all 600 drives piles by means of dynamic pile tests. For the calibration of the dynamic pile tests, 6 static pile load tests were carried out. The execution of the construction and the results of the extensive tests on the building site are shown.

Jan 1, 1989

By Lawrence P. Goldfarb

This paper presents the results of the geotechnical investigation for the repair of the Fashion Island Boulevard Bridge, Bridge No. 350160, in San Mateo, California. The concrete, precast girder bridge suffered considerable damage during the Loma Prieta earthquake. The existing 36-inch, precast, prestressed concrete piles cracked and spalled at their tops. Based on analyses performed by Biggs Cardosa Associates, structural engineers, the piles did not have sufficient strength and ductility to resist the dead plus seismic loads specified in the Caltrans "Bridge Design Specifications". Additional support for the bridge was needed and the repair strategy consisted of installing large diameter pipe piles at the existing bent and abutment locations. This paper describes the geotechnical engineering analysis and design decisions for the large diameter pile design.

Jan 1, 1993

By Mark Maday

As part of the I-94 North-South Corridor reconstruction program, the Wisconsin Department of Transportation (department) is reconstructing the Mitchell Interchange in Milwaukee, Wisconsin. Located on the south side of Milwaukee near Mitchell International Airport, The Mitchell Interchange interconnects I-94, I-43 and I-894. Reconstruction began in 2009 with the letting of the first advance contract for local crossroad bridge reconstruction. A second advance contract for construction of collector-distributer roads on each side of the I-94 mainline was completed in 2010. The main contract involving reconstruction of the core of the Mitchell Interchange was let in the summer of 2010, and is scheduled to be completed by the end of 2012. The core contract includes construction of three cut and cover tunnels along two system interchange ramps. Construction of the three tunnel structures is on the critical construction path. The contract includes an interim contract completion date that requires the tunnels to be open to traffic by the end of 2011. A top down method of construction using drilled shaft secant piles for the sidewalls of the cut and cover tunnel structures was selected as the preferred structure type to address subsurface and construction schedule challenges. The department identified in pre bid coordination that no cost reduction incentives would be reviewed or accepted for changes in tunnel wall type. A major component of the tunnel structures requires the installation of 1,500, 4-foot diameter secant piles. This paper presents mitigation strategies to manage construction risks associated with the installation of the secant piles including; prequalification of the secant pile subcontractors, requirement for use of full depth temporary casing, a site specific quality control plan, specifying drilling equipment, and developing a geotechnical baseline report for this critical component of the Mitchell Interchange reconstruction project.

Jan 1, 2011

By Sheryl D. Gallagher

The project consisted of filling an abandoned underground limestone mine to facilitate construction of a new entrance ramp to I-470 in Lee?s Summit, Missouri. Due to collapse of mined areas near the project site, design included determination of the limits of remediation for the project and minimum construction requirements for mine infilling. The Judy Company, contractor selected for the mine infilling, experimented in the laboratory with several grout mixes to determine the appropriate mix for the project. Infilling was accomplished from the ground surface, and camera observation was used to monitor the barrier wall construction and infilling process. It was discovered that some of the mapped rooms were larger and some were smaller than indicated on the construction plan.

Jan 1, 2009

By Tracy Brettmann, Will Bohlen

An innovative retaining wall design consisting of tangent drilled shafts with supplementary seal piles was used to limit continuing bank erosion along the Brazos River in Southeast Texas. The riverbank erosion had progressed to where it was threatening the stability of both the bridge abutment and corresponding approach embankment of the heavily travelled Highway 99 bridge at this location. A tangent pile design was selected because it was both much faster to install and more cost effective than a secant pile system. The design included both 5.5-ft and 10-ft diameter shafts with depths up to 130-ft and comprised both anchored and cantilevered sections. Supplementary seal shafts were also installed between the structural tangent drilled shafts to help plug any gaps between the tangent shafts. The plumbness and diameter of the shafts were tested using a sonic caliper to make sure the shafts were installed within the specified tolerance. The initial design had to be revised when a record flood from Hurricane Harvey impacted the site during construction. Introduction The Fort Bend Grand Parkway Toll Road Authority (Owner) needed to protect the north bridge abutment with a retaining wall system due to rapidly eroding conditions of the Brazos River banks within the 300- feet-right-of-way of the State Highway 99 Jodie Stavinoha Bridge. The extent of the local scour and erosion along the north bank of the Brazos River has caused concern for the structural integrity of the bridge. The magnitude of the erosion along the north bank at the location of the bridge has been measured at about 120 feet over three recent hydrologic flood events locally referred to as Memorial Day 2015, Memorial Day 2016, and Tax Day 2016. During construction, a new record flood level occurred due to Hurricane Harvey in August of 2017 that resulted in a portion of the retaining wall needing to be redesigned due to even more erosion occurring. The Brazos River is an actively eroding and meandering alluvial river plain that naturally meanders and migrates over time. The processes of bank erosion and meander migration were ongoing before the bridge was constructed and will continue in the future. These recurring major flood events, however, rapidly increased the rate of erosion in just a few years. Background. Due to the need to protect the bridge as soon as possible, the Owner selected a project team consisting of the designer, general contractor and specialty deep foundation contractor prior to final design to work together in developing a cost-effective design that could be implemented rapidly. The project team initially considered both a secant pile and tangent pile retaining wall system using drilled shafts. After reviewing various alternative designs, a tangent pile wall with seal piles was selected based on both cost effectiveness and speed of installation. The tangent pile with seal pile option was approximately 20 percent lower in cost and 50 percent faster to install.

Jan 1, 2018

Jan 1, 2002

By Mohammed Y. Fattah, Wissam H. S. Al-Sudani

"During installation of pile, a soil column is formed inside the pile. For small depths, the height of the soil column typically equals to the penetration depth (full coring state). As the penetration depth increases, the developed internal shear stresses become larger and reduce the amount of soil to penetrate. At the same time, the soil in pile at the bottom is compacted. This will continue until at a given moment, the soil column is a soil plug, and does not stop moving relative to the pile. This is because the shear stresses developed in the interior of the pile are greater than the load-bearing capacity of the ground.This paper presents the results obtained from 40 model pile tests carried out to assess the effect of soil plug on the model pile capacity. The piles are embedded in sand of different densities with different lengths of piles and types of pile-ends. The model tests are divided into two parts according to the type of end of the pipe pile used in the model pile test. The first part consists of 32 model open-ended piles with different lengths of soil plug inside the pile. The second part consists of 8 model closed-ended piles.It was concluded that open-ended pipe piles behave as a closed-ended if the soil plug formed inside piles in state partial plug or full plug. Length of soil plug depends on the type of installation and relative density. The pile load carrying capacity in dense sand is several times greater than those in medium sands especially in cases of closed ended piles or open-ended since the pipe pile can produce external and internal skin friction in addition to end bearing resistance that makes the total pile capacity close to that of closed-ended pile. Whether open-ended piles are driven or pressed in the fully coring - fully unplugged mode or in the partially plugged mode, the plug does contribute to static pile base capacity."

Jan 1, 2014

By Richard D. Short

The Pseudo Static Pile Load Test, PLT, is a rapid method for determining pile capacity. Pile design is usually based on theoretical calculations of ultimate load capacity using soil data from a field investigation. The pile capacity is confirmed during construction by analysis of blow counts using dynamic formulae, dynamic pile monitoring, and load testing. Load testing is the most direct and reliable method of determining the actual capacity of a pile. Conventional load testing procedures, however, are time consuming and expensive. A typical load test requires installation of two to four reaction piles, construction of a high-capacity steel test frame, hydraulic jacks, and dial gauges, and will typically take one to three days per pile. Costs for load tests range from $10,000 to $20,000 per test. The Pile Load Test machine features a 25-tonne weight mounted on a mobile test frame. PLT load tests can be performed in a matter of minutes once the equipment has been mobilized to the site. This paper examines three test sites where the PLT test method was used and compares the results to conventional load test results and theoretical capacity calculations.

Jan 1, 2000

By Federico Pagliacci, Marco Chiarabelli, Salvatore Miranda

The paper describes the adopted technologies and performance controls related to a special geotechnical engineering solution provided within the scope of the Galataport Project, in Istanbul, Turkey. The scheme is the one applied to the new quay of Salipazari, which is a combination of retaining structure and ground improvement, formed by a combi-wall, a reinforced concrete diaphragm wall and a soil improvement by deep soil mixing (Turbojet). The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high profile Project. The results of the in-situ and laboratory tests carried out on the improved soil are also presented. Main discussed points are: • History of Galataport and main Project details. • Design principle and soil condition for the new quay of Salipazari. • Difficulties encountered during execution of DSM. • Preliminary field trial tests conducted to establish the operational parameters, with relevant in-situ and laboratory tests executed. • Preliminary tests on material used for DSM (seawater and CEM IV SR). • Electronic equipment mounted on the rig, which allows the automatic execution of DSM columns. • Final QA/QC tests conducted to verify the performance of DSM, mainly consisting in: coring with relevant laboratory tests on samples (UCS + Es), seismic refraction tomography and seismic cross hole tomography. Correlations between UCS and Es, and between Es and Edyn are also presented. • A cross section of the executed treatment could be inspected on site during excavation. Photos and considerations are also presented.

Jan 1, 2018

By Daryl W. Wurster

The Liberty Bridge in Greenville, South Carolina is a curved, cable-stayed, pedestrian bridge with primary support provided by two towers. The bridge is part of the Falls Park redevelopment. The bridge was originally designed to be supported on drilled piers. Alternately, the bridge was supported on a combination of micropiles and anchor piles because of difficult access and subsurface conditions. The use of micropiles and anchor piles led to improved construction scheduling and reduced costs. Micropiles were used to resist compressive loads. Anchor piles were used to resist tensile forces and to eliminate excessive settlement of pile caps into underlying fill during pre-stressing. This paper describes the site history, bridge construction, site and subsurface conditions encountered, and the decisions that led to support of the bridge using micropiles and anchor piles and foundation construction.

Jan 1, 2006

By Robert A. Field

Static-Load Piledriving utilizes a hydraulic push to facilitate the installation of a pile. The pile is not rotated, impacted or vibrated. A smooth pushing force advances the pile incrementally into the ground. Static-Load devices must have a reaction mass to push against. The most simple form of a Static-Load device is a jack; more advanced equipment, such as the Still Worker, also utilizes this approach. This paper focuses on the use of the Still Worker on three challenging projects. In each case, the existing site conditions made it risky, or unattractive, to utilize conventional impact, vibratory, or drilled-shaft equipment.

Jan 1, 1997

Jan 1, 2002

By Zachary Q. Maassen

The purpose of this paper is to highlight the environmental benefits of properly managing slurry waste as it is generated on site. The following projects will be used to illustrate the importance of proper onsite waste management. Project: Jet Grout Backflow Dewatering The goal was to dewater the backflow directly onsite to produce a dry, solid waste and reusable water. The backflow spoil was pumped directly to the dewatering system as it was generated. Utilizing mechanical separation equipment and flocculation polymer the waste volume was reduced by 44%. Due to the site footprint and high volumes, slurry waste removal and onsite processing were the only two feasible options. Onsite dewatering proved to be the environmentally beneficial option as it eliminated the need for slurry waste hauling and disposal. The benefits of utilizing a dewatering system are listed below: Project: Soil Mixing Spoil Recycling for Slurry Wall Construction In this application the spoils generated contain bentonite mud, cement mixture and organic ground soils. The goal of this project was to process the backflow mixture to recover reusable bentonite mud and separate the soil as a dry, stackable waste product. The treatment system replaced the traditional method of vacuum truck extraction and facility disposal. The environmental benefits of properly handling the backflow is a decrease in fresh water usage, bentonite additive reduction, and the reduction of CO2 emissions. The paper will consist of a project scope, technical equipment and process description, environmental impact reduction calculations and lessons learned for each project.

Jan 1, 2018

By José L. M. Clemente, John R. Davie

"Abstract An extensive pre-production static and dynamic pile load testing program was conducted for a coal-fired power plant. The static load testing program included axial compression, uplift (tension), and lateral load tests. Three types of piles were tested: Monotube, closed-end pipe, and step-tapered. The load tests were used to (a) determine pile driveability characteristics for each pile, (b) verify pile load response behavior, and (c) provide data to support the selection of a cost-effective piled-foundation system for the plant. A recent publication (Clemente and Lewis, 2013) describes the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript describes site subsurface and groundwater conditions and installation of probe piles for testing, focuses on the uplift and lateral load testing program, and provides a comparative interpretation of the load test results.INTRODUCTIONThe pre-production probe pile load testing program described here was conducted for a 202-megawatt, coal-fired power and steam generating (cogeneration) facility. A schematic layout of the main plant (power block area) is shown in Figure 1, which also includes the locations of clusters of preproduction probe piles and boreholes drilled near these clusters.The load testing program included 24 pre-production probe piles driven throughout the power block area. The probe piles were driven at locations T-1 through T-8, shown in Figure 1. Three types of piles were driven at each location: Monotube pile; closed end, straight shaft pipe pile; and step-tapered pile. At each location, the three piles were driven in a row with the pipe pile at the center, and the center-tocenter spacing between piles was equal to about 1.5 m (> 3.5 pile diameters for the largest pile). No pile cap was used to connect the three piles, and the three piles driven at locations T-1 through T-8 will be referred to as pile clusters. A complete suite of static load testing (compression, tension, and lateral) was performed on each individual pile at Cluster T-2 and on the step-tapered piles only at Cluster T-8, shown in Figure 1.Clemente and Lewis (2013) provide details of the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript focuses on the uplift (tension) and lateral load testing program. A brief summary of the site geology and existing subsurface and groundwater conditions in the vicinity of the test pile clusters is presented, with emphasis on T-2 and T-8. Probe pile driving results at T-2 and T-8 are also presented. Descriptions of the static uplift and lateral load test program at T-2 and T-8 are given along with a comparative evaluation of the load test results."

Jan 1, 2014

By Wei Zheng

A pulverized coal fired power plant is being built in Osceola, Arkansas, along the Mississippi River. The subsurface soil conditions consist of a certain amount of very soft clayey silt and clay underlain with a medium dense sand layer and a dense sand layer. The site has been raised four to five feet with fill material consisting of sand and gravel. Consolidation settlement due to the fill is expected to cause negative shaft resistance (downdrag) on the pile foundations. The site is located in a high seismic hazard area - the New Madrid Seismic Zone (NMSZ). The liquefaction analyses indicated that there is a high liquefaction potential in the medium dense sand layer. Load tests are needed to determine the shaft resistance and the end bearing of each soil layer for design purpose. Two types of pile foundations ? augered pressure grouted displacement pile (APGD) and partial augered pressure grouted displacement pile (P-APGD) were considered for this project. Ten pile load tests, including five compression tests and five tension tests, were performed for three different areas. Strain gauges were installed for the compression tests. The APGD and P-APGD piles were installed side by side for comparison. In addition, three additional dynamic tests were performed to supplement the information from the static load tests. Load deflection curves for the compression tests were predicted, and the failure loads were interpreted using four different methods. The shaft resistance and the end bearing were determined from the strain gauge data and were used to back calculate the ultimate capacity. The back-calculated capacities are in good agreement with the predicted failure loads; they were further verified with the tension load test results.

Jan 1, 2007

By Michael Quadagno

Hudson River Pier 86, home of the historic USS Intrepid Aircraft Carrier and the Intrepid Sea-Air-Space Museum, is currently undergoing a $30M reconstruction. This project involves the demolition of the old timber pile supported pier and construction of a new 150 ft wide by 782 ft long concrete pier, built over the footprint of the old piles. The new pier consists of steel pipe piles, precast concrete pile caps, and a composite deck, made up of precast, prestressed concrete planks and cast-in-place concrete topping. This paper focuses on both the structural design and construction of the new pier, with emphasis on the pile foundation. Pier 86 is unique in that it is required to resist the extremely high lateral loads imposed on it by the permanently moored 898 ft long aircraft carrier during severe storms. A total of 360 steel pipe piles support the new pier. These piles, which are 24 in. in diameter and range in length from 58 ft to 175 ft, were driven down to bedrock. The piles, each having 200 ton allowable capacities, work together to resist the significantly large lateral loads exerted on the pier by the ship. The installation of the piles was unique in that all the piles, including the ?super-longs?, were fabricated to-length offsite, delivered to the site via truck and barge, and installed in one piece, eliminating the need for field splicing. The Pier 86 reconstruction will be completed within an extremely aggressive 18 month schedule, from January 2007 through June 2008. The refurbished aircraft carrier Intrepid will return home in September 2008, and the grand re-opening of the pier will be on Veteran?s Day 2008. This paper provides a case history for owners, government agencies, engineers, and construction professionals that will be faced with the challenges of designing and building new piers.

Jan 1, 2008