Search Documents

By V. Coffin, T. Cienski

"(Figure 1) Reagentized pulp enters into the column at about 1/4 of the distance from the top. Inside the column it meets with a downward flowing stream of water and with an upward flowing mass of air bubbles. Flotation takes place in this counter current system while at the same time fine gangue particles are washed off the froth before it reaches the overflow lip at the top of the column. The main operating features of the column flotation are as follows:a) No moving parts. Solids are kept in suspention not by an agitating action of a propeller but by settling down against the rising air bubbles.b) Wash water. Spray pipes are installed a few inches below the froth surface and deliver required volume of water. The purpose of this water is twofold:(i) it keeps in balance the flow of material through the column and(ii) it washes rising froth in the froth layer as well as removes unwanted fines attached to the bubbles at the lower flotation section. As a result the concentrate produced is of higher purity than in the conventional flotation. Column is characterized by very high up-grading. However, even temporary disruption of wash water supply results in a drastic drop of concentrate grate.c) Flow balance. (Figure 2) For the correct operation volume of the underflow (tail) is larger than that of the feed. The difference is made up by the wash water. This difference called bias is predetermined and ranges from some 4 to 15 USGPM depending on the size of the unit and process requirements."

Jan 1, 1981

By Staff

This paper contains an outline of the history of the Sullivan mine, now owned and operated by the Consolidated Mining & Smelting Company of Canada, Ltd.; some account of the various methods by which the ore has been treated in efforts to solve the metallurgical problems which its complex character presents, and, finally, to give, as concisely as possible, an outline of the present mining and metallurgical practice along with a description of the mining and milling plant at Kimberley and the smelter and refineries at Trail, in British Columbia. EARLY HISTORY In May, 1892, Pat Sullivan, John Cleaver and Mike Holland left the Coeur d'Alene country, in the State of Idaho, to seek their fortunes in the Kootenay lake district in British Columbia. They were aided in their venture by James Cronin, afterwards locator and owner of the St. Eugene mine at Moyie. Two months later the party broke up, Sullivan and Cleaver crossing the mountains from Crawford bay on Kootenay lake to the head waters of the St. Mary's river, the course of which they followed down to Fort Steele. Here they found a good deal of excitement about the North Star mine, and, joined by "Ed." Smith, who was familiar with this part of the country, they determined to return and prospect in its vicinity.

Jan 1, 1924

By Malcolm Scoble, Jean-Marc Robert, Luciano Piciacchia

"An approach to the in situ testing of mine backfills is outlined. It has been developed to provide a measure of the effective strength and stiffness of such materials after placement in stopes. This paper is based upon recent field studies undertaken at five Quebec mines. Details of the selected instrumentation, supporting equipment and testing procedures are reviewed. The mechanical behaviour of the backfills is reported and related to their physical properties. This approach represents an economical, simple and reliable means to assess the mechanical characteristics of backfill materials as an aid to both mine design and placement quality control. IntroductionDevelopments in backfill and mining method technology are creating a pressing need to develop effective techniques for characterizing the physical and mechanical properties of backfill in situ, rather than relying on traditional laboratory testing. The development of bulk mining methods is creating the requirement to more fully understand the nature of exposed fill faces to design for stability in pillar recovery operations. Other backfill technological developments currently receiving widespread attention are high density placement and the use of alternative additives to Portland cement. In Canada, U.S.A. and South Africa attention is also being placed on employing backfill to alleviate rockburst hazards(1,2.3l. In situ testing offers the potential to measure the geomechanical properties of backfill once placed in stopes , in order to assess its actual role in pillar recovery and ground support. Similarly, it offers the ability to provide some quality control during backfill placement. This role is seen as becoming increasingly important with the growing recognition of the need to pay greater attention to the mode of placement, which governs segregation and variation in the properties actually achieved by the backfill after placement."

Jan 1, 1987

Westwood Quebec Long Life, Low Cost CONSTRUCTION UPDATE ? Shaft advanced to 840m (after 1 year), 3 km of down ramp and 2 km of exploration drift ? Head frame and hoist room structure completed ? 2009, 84,700m drilling program completed (increase 9%) 2010 OUTLOOK ? $102 million expenditures planned ? Shaft to advance to 1,300m and the first loading excavate 71,500m drilling program planned

May 1, 2010

By J. Lee, R. G. Rosehart

"The basic problem of arsenic contamination from mine water is discussed. Effective methods of removal involving chemical precipitation, activated carbon adsorption, ion exchange and reverse osmosis are discussed. As well as an economic analysis, detail is also paid to other ions in solution which are removed simultaneously.INTRODUCTIONThe object of this paper is to review arsenic and its removal from gold extraction plant effluents. The first method considered is chemical precipitation. A second method is sorption processes, such as ion exchange resins and activated carbon adsorption. A third method is the possible application of reverse osmosis for the treatment of mine waste waters containing arsenic.Arsenic pollution in the gold mining communities of Canada and Ghana have been extensively studies (l, 2). Lynch(3) Shabunin, Gutman and Kogan( 4), Hollo, Troth, Vennes and Illinigi (5) and Hau(6) have reported their removal methods of arsenic by chemical precipitation, ion exchange and biological methods. Their conclusions were that the precipitation with Fe2+ and Fe3+ ions was most effective.Scope of the ProblemInitial aspects of this research program involved a detailed analysis of the operation of a gold extraction plant located in Canada. The name and location of the mine is proprietary information. Figure 1 gives a basic process schematic with the main tailing streams identified.Table 1 gives information as to the various mine streams and their physical and chemical composition. In this study, primary attention is paid to the removal of dissolved arsenic from waste waters. Solids from this type of operation can always be back-filled. As could be anticipated, the dissolved As content of the primary flotation tailing stream is very low. The dissolved As level in the secondary processing stream and the roasting quench water is quite high. The reason being that at this stage of the process, the arsenic has been freed from the arsenopyrite forms."

Jan 1, 1972

By Jim Dodd, Jim Paynter

"We would like to acknowledge the efforts of the following key people who helped to make this project a success.Ron Jung, instrumentation supervisor for the Golden Giant Mine, spent many hours reviewing process and instrument drawings, selecting instruments and providing hands on support during commissioning.Andy Keough, underground production supervisor for the Golden Giant Mine, was responsible for readying the underground distribution network for paste backfill.H.A. Simons Ltd. personnel who did an excellent job providing sound conceptual and detailed engineering.Fred Brackebusch, of Mine System Design who designed the paste backfill delivery systemPierre Lacombe, mill superintendent of the Louvicourt Mine, generously shared information and operating experience of their paste backfill plant.AbstractThroughout the 11 year history of the Golden Giant Mine, the primary backfilling method made use of consolidated rock fill. New backfill technologies have developed over recent years which now make it possible to use large quantities of fine mill tailings as backfill.In January of 1996, construction began on a new paste backfill plant at the Golden Giant Mine. Six months following, the plant was commissioned. This paper describes the design, commissioning and operational experience to date of the paste backfill plant."

Jan 1, 1997

By Mike Sapiro

"Heath Steele Mines is a base metal producer situated near Newcastle, N.B. presently treating 3500 TPD of complex Cu-Pb-Zn ore. The ore consists of massive fine grained sulfides averaging I. 1% Cu, 1.6% Pb and 4.5% Zn.The original mill started in 1956 at 750 TPD and was successively expanded through 1500 to 3000 TPD in 1969. In 1972 an expansion to 4000 TPD was initiated. It was planned to obtain the maximum benefit from equipment and manpower by adding some process equipment, instrumentation, an on stream analyser, and a process control system. The benefits from this approach could be greater than normally expected, because of the complex metallurgy of this ore.IntroductionThe crushing plant is of conventional design with two 5 ½ ft, Symons cone crushers with the crushed ore screened to -7/8 inch on a 61 x 16 1 Al I is Chalmers vibrating screen and stored in four 1000 Ion bins. There are two para I lei grinding circuits, each one consisting of the following: one Rod Mill in open circuit, one Ball Mill in closed circuit with two 20"" Krebs cyclones, and one Ball Mill in closed circuit with three 15"" Krebs cyclones, Al I the Mills are 9' x 121 Al I is Chalmers Mills. The secondary cyclone overflow from each grinding circuit is thickened and combined to form flotation feed. The final product is 65% - 400 Mesh. Two regrind mills have been installed as part of the expansion."

Jan 1, 1977

By Tom C. Palangio

The mining industry has come to rely on imaging devices to monitor and record all kinds of activities. We use them to measure, improve the process, ensure security, increase production and automate machinery. Cameras can be installed in locations most people wouldn?t want to live and be our ?eyes? to record the events at that location. This paper discusses digital imaging, the equipment, methods, techniques and information that can be learned from digital devices used in mining operations. The guy who said ?a picture is worth a thousand words? probably understated it. Images are the perfect way to document conditions before, after and even during mining activities. Today?s wide choice of cameras, camcorders and other digital devices allow us to record most activities and events. The technology is advancing at a high rate. Digital cameras and camcorders are marvels of technology with high resolution optics, compact size, automatic time and date stamp, great battery life, shutters to freeze motion and computers to auto focus and eliminate jitter (image stabilization). Add to this the economical price and ease of use and everyone in this industry should be aware of the possibilities.

Oct 1, 2010

By Michael W. Hinds

X-ray Fluorescence Spectrometry (XRF) is used at various stages of gold refining. Initially, incoming impure gold is analysed for deleterious elements such as As, Cd, Hg, Se, and Te. Based on the levels of these impurities the material can be returned to the client or accepted for refining. XRF is also used to determine the metal concentrations after the impure gold has been melted and sampled. This information is used to assist the final Fire Assay determination of gold and silver. An energy dispersive XRF is used to determine the end point of chlorination refining step.

Jan 1, 2011

The primary steel industry of the Prairie Provinces consists essentially of three companies whose total annual melting capacity, as of January 1, 1963, was 333,000 net tons. These companies have steel rolling facilities. In addition, there are five other companies producing steel castings by melting scrap in electric furnaces which, with the plants having rolling facilities, gives a total annual furnace melting capacity of 380,000 tons. Since 1954, the annual production of steel ingots and castings has ranged from a low of 66,588 tons, in 1954, to a high of 211,138 tons in 1961. The present facilities on the Prairies for making steel ingots from scrap, and rolling them to produce light merchant mill products, appear to be sufficient for many years ahead. Steel scrap, as electric furnace feed to make steel ingots for the present line of products, will probably continue to be available at reasonable prices either on the Prairies or from the north-central United States. It is recognized, however, that residual elements in scrap may be-come of greater significance and necessitate more rigid control of scrap quality.

Jan 1, 1963

By F. Halverson

"The theory of flocculation usually is in a state of flux, involves many diverse phenomena, and is complex and sometimes contradictory in details. Instead of attempting a general discourse, I shall discuss selected observations made at our Stamford Laboratories, which impinge on theoretical aspects in two somewhat distinct areas of flocculation. Since some of you many not be familiar with flocculation, and :.n order that we all attach the same meaning to the jargon used, I first would like to review briefly a generalized picture of what goes on.Assume we have a suspension of particles in water, with a distribution in the sizes of particles. The surfaces of the particles interact to some extent with the water--· tending to alter the extent of hydration, may generate some ion exchange, all being somewhat variable with time--developing a surface condition which is very complex in details. We refer to this suspension as the ""substrate.""In the usual situation, if the suspension is allowed to stand quietly, the large particles settle out first, with somewhat smaller particles settling more slowly, and then there is a portion of very fine material which takes a long time or doesn't settle out at all. This resistance to settling t~ the very fine particles results from many factors, but all relate back to the size and density of the particles, to their surface properties, and to the other components in the aqueous suspending medium."

Jan 1, 1978

By M. Tarvainen

"Lately, the development work in closed circuit grinding has mainly been focused on mills and on different types of instrumentation, mathematical models and automation in spite of the fact that the poor efficiency of the classifier is well known. It has also been proven by several investigations that by improving the sharpness of classifier separation, remarkable technical and economical advantages can be achieved. Some attempts to improve the performance of the most common classifier, hydrocyclone, have been made, among them injection of wash water above the spigot cyclone and retreatment of either or both of the products of the primary classifier. No method has been successful enough to achieve general adoption in the industry. The purpose of this paper is to introduce some industrial results achieved by two-stage classification where the coarse product of the turbulent-flow classifier, hydrocyclone, is cleaned in a laminar-flow cone classifier.The main target of the adoption of the two-stage classification circuit it naturally to improve the sharpness of size separation. This again leads to the following advantages in the grinding process:- lower circulating load and increased capacity- lower energy consumptionnarrower size distribution in the fine product- less overgrinding and less slimes- reduced specific surface areaThese improvements, no doubt, reflect on the subsequent concentrating process in the following aspects:the rate of flotation is improved, less reagents and energy is neededthe recovery and grade of valuable minerals in concentrates is improved- savings in dewatering can be expected- less fines in tailings improve the conditions for water recirculation."

Jan 1, 1980

By Terry A. Kirk

"This paper describes Derrick High Frequency Vibrating Screens and their process performance in grinding circuit applications. The benefits of screen sizing in closed circuit grinding are illustrated by case histories from a wide spectrum of mineral industries.INTRODUCTIONHigh capacity, reliable wet screening equipment is increasingly in demand by the mining and allied industries for separations finer than 1/.7 5mm (I/ mesh). The continuing search for improved energy efficiency and reduced steel consumption in comminution has Jed to greater scrutiny of every aspect of circuit design and operation, including the classifier efficiency (selectivity) function.Derrick Manufacturing Corporation has been developing high frequency screening machines designed specifically for grinding circuit applications since 1973. Successful installations are currently operating in iron ore, copper, coal, uranium, phosphate and other extractive industries."

Jan 1, 1984

By Costa

The fly-in-fly-out (FIFO) mining model has significant implications for the industry as it plays an important role in fulfilling the economic, social and workforce needs of the contemporary mining industry. It has increasingly been adopted in countries such as Canada and Australia, but is the current nature of the FIFO model challenging the place women have achieved in the mining workforce? Research in the mining and oil and gas industries reveals that major sources of stress for fly-in-fly-out mining workers are the times of parting and of reunion, the challenges in defining roles within the family, parenting, and conflict between spouses over the use of the leave time and money. So how are women in the industry coping with the FIFO schedules and consequent intermittent relationship with families and partners? How is the mining industry adapting to recruit and maintain female employees in FIFO operations? This paper describes an exploratory study conducted in Canada, which intended to provide some initial insights that might help us answer the questions above. There are several inferences made from this exploratory study. It is clear that FIFO poses significant challenges for both female and male workers. It is largely seen as rigid, extremely challenging for employees with young families and workers who are single mothers, and it is generally incompatible with starting a family and caring for small children. FIFO creates severe stress on relationships and on workers psychological well-being. It seems to be indeed harder for women, since they are often in lower paying positions and therefore have less financial reward for the FIFO lifestyle. On the other hand, FIFO creates the opportunity for young women, including Aboriginal women, to jump-start their careers, as well as opportunities for mature women to work while pursuing other personal interests during their time off. This paper concludes with recommendations to improve the FIFO system in order to increase the ability of mining companies to hire and retain women

May 1, 2006

By Véronique Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modeling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioniong of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

May 1, 2003

By G. Hausen, H. Micka

"Modern signal and power electronics made adjustable-speed AC drives technically feasible and reliable and economically attractive. Cycloconverters are discussed as a proven technology for mine hoists. \IntroductionUntil rather recent technical and commercial advances in power and signal electronics, DC motors were used almost exclusively for applications requiring continuously adjustable operating speeds and torques. More recently, the significantly higher efficiency and the accordingly lower operating costs of AC motors gained importance. An effective and efficient speed control of AC motors requires the control of AC voltage and frequency. Table 1 shows typical applications of adjustable-speed AC drives.CycloconvertersOf particular interest to the mining industry are cycloconverters for hoist drives. The cycloconverter represents by far the simplest, most efficient and most economical means of converting a constant-voltage, constant-frequency supply into an adjustable-voltage, adjustable-frequency supply as required for the speed control of AC drives operating in the frequency range to half of the utility frequency.Cycloconverters feeding synchronous motors or induction motors are ideally suited for slow-speed direct-coupled drives."

Jan 1, 1988

By T. T. Chen, W. Petruk

The mineralogy of the feed, concentrates and tailings from the Heath Steele mill in New Brunswick was studied in detail to determine the liberation and recoveries of the major ore minerals, and to characterize the occurrence and distribution of the trace elements. The ore milled during August 1977 contained an average of 4.34 wt % Zn, 1.25 wt % Cu, 1.64 wt % Pb and 90 gr/ton Ag. The main trace elements in the ore are silver, cadmium, indium, cobalt, antimony, bismuth, arsenic, mercury, tin and gold. Silver is carried in solid solution in tetrahedrite-tennantlte, galena, Ag-Sb sulfosalts and Pb-Bi-Sb sulfosalts. Approximately half of the silver is recovered in the lead and copper concentrates and the remainder is lost in the tailings and Zn concentrate. As the major silver-bearing minerals also contain Sb and Bi, recovering silver by ore dressing would involve recovering elements that are troublesome in extraction metallurgy. Cadmium and most of the indium and mercury occur in solid solution in sphalerite and consequently are recovered in the zinc concentrate. Some indium is also recovered in the copper concentrate in a second unidentified indium-bearing mineral. Cobalt and arsenic occur principally in arsenopyrite, cobaltite, a Co-Fe sulfarsenide, pyrite and pyrrhotite, and follow these minerals into the tailings. Recovery of the valuable element cobalt, therefore, would involve recovering the environmentally hazardous element arsenic. Most of the tin and gold report to tailings. The ore was ground to about 80% minus 270 mesh. At this grind, 71 wt % of the sphalerite, 66 wt % of the chalcopyrite and 59 wt % of the galena were liberated. Recoveries of free sphalerite, free chalcopyrite and free galena in the Zn, Cu and Pb concentrates were 85 wt %, 76 wt % and 80 wt %, respectively; recoveries of unliberated sphalerite, unliberated chalcopyrite and unliberated galena in the respective Zn, Cu and Pb concentrates were 48 wt %, 5 wt % and 7 wt %. Some of the unliberated sphalerite and chalcopyrite grains in the tailings are large and would have been liberated at a finer grind.

Jan 1, 1980

By J. Coffin, R. Multani, C. Deredin

Glencore’s Strathcona Mill has recently evaluated a pyrrhotite depressant combination of diethylenetriamine (DETA) and sodium metabisulfite (SMBS) to improve its overall plant pyrrhotite- pentlandite (Po-Pn) selectivity, with the aim of producing a higher quality nickel concentrate. In a previous paper, key findings from a comprehensive lab-scale program (completed at the XPS Centre) were summarized where, of the depressants tested, DETA/SMBS combination was found to be the most effective in improving the Po-Pn selectivity. The present paper describes the metallurgical program recently completed at Strathcona Mill; DETA/SMBS evaluation on select plant “grab” samples as well as the major results of three DETA/SMBS plant trials conducted on several plant ore feeds (long-term testing). Interestingly, it was found that there was variable success in using DETA/SMBS depressants on the different plant ore feeds; DETA/SMBS (dosage: 25/50 g/t milled feed) on lower Cu feeds demonstrated a ~2% Ni recovery increase at the same Ni grade. On the other hand, higher Cu feeds demonstrated virtually no benefit from DETA/SMBS at the same plant dosage, suggesting that higher DETA/SMBS dosage (at specific locations) than that tested is required to overcome the increased Cu-DETA complexation for these particular feeds. Glencore Nickel – Sudbury Integrated Nickel Operations owns and operates Strathcona Mill which has been processing Ni-Cu ores from the Sudbury Basin since 1968. The valuable sulfides are pentlandite (Pn) – (Ni,Fe)9S8 and chalcopyrite (Cp) – CuFeS2, majority of the sulfide gangue is pyrrhotite (Po) – Fe(1-x)S [0 < x ≤ 0.125] which is present in two forms: hexagonal Po (Fe9S10) and monoclinic Po (Fe7S8) (Multani & Waters, 2017; Lawson et al., 2014). Currently Strathcona Mill processes ore mined from two primary sources from the Sudbury area and produces two concentrate streams: (1) nickel-copper concentrate that is sent to the Sudbury Smelter; and (2) copper concentrate that is shipped to the Fonderie Horne (Glencore Copper, Rouyn-Noranda).

Jan 1, 2019

By G. A. Kosick, C. A. Harris

"Metallurgy at the Polaris Mine is approaching an impasse, with lead and zinc concentrate grades and recoveries approaching their theoretical maximums. In an effort to increase productivity, plant throughput and operating material costs became a major focus of milling personnel.one method of increasing plant throughput was to minimize flotation circuit upsets by; standardizing operating strategy, decreasing control action response time of operators, increasing training of operators, and providing a more available decision support system for operators.To achieve these goals, Polaris personnel decided to utilize expert system technology to develop a real-time process controller for the flotation circuit which would be capable of justifying its actions to operating personnel.This paper describes the procedures followed in constructing the first process controller in the mineral industry which is based on the principles of Artificial Intelligence.IntroductionThe Polaris Concentrator was constructed in 1980 on a barge in Trois Rivieres, Quebec and towed to its present location on Little Cornwallis Island, North West Territories, about 1450 kilometers from the North Pole. The plant presently treats about 2,800 MTPD of new feed with average feed grades of 3% Pb, 13% Zn and 5% Fe. Current production averages 36,000 tonnes of lead concentrate and 220,000 tonnes of zinc concentrate annually.In an effort to increase the efficiency of the concentrator, the decision was made to implement an innovative control system on the flotation circuit. This system would embody and utilize heuristics ""rules-of-thumb"" gained from operators to make on-line process decisions. It would also justify these decisions on a demand basis."

Jan 1, 1988

By V. Prostakova, M. Shevchenko

The copper smelting gas / slag / matte / metal / solids system with the Cu-Fe-Ca-Si-O-S major elements has been a long-term focus of the present overall research program using integrated experimental and modelling approach for the phase equilibria characterisation and development of a thermodynamic database. A systematic investigation of phase equilibria of slag systems in equilibrium with Cu metal is providing information for systems where copper coexists in slag with lead, zinc, and aluminium oxides as major components. Experimental studies involve high-temperature equilibration of synthetic samples; rapid quenching; and measurement of the compositions of equilibrium phases using electron probe X-ray microanalysis (EPMA). Particularly important feature of the present study a wide range of temperatures (660-1670°C) being characterised that reveals major inconsistencies in the existing thermodynamic description of the multicomponent system, and allows to establish the thermodynamic properties from phase equilibria in a reliable way. FactSage-based thermodynamic modelling is integrated with experimental research. Initial thermodynamic assessments are used to identify priorities for experiments, planned to provide specific data for thermodynamic optimisation. Significant improvement in the accuracy of the phase equilibria description is achieved, in particular in the PbO-Cu2O-SiO2, ZnO-Cu2O-SiO2, and Cu2O-CaO- Al2O3 systems in equilibrium with metallic Cu. INTRODUCTION Slags high in lead and copper are generated in primary metal production in the smelting of lead sulfide concentrates and in pyrometallurgical metal recycling systems. The compositions of these slags are varied due to increased fraction of recycled materials in the feed as well as introduction of previously unused chemical elements to modern technology. Therefore, their processing becomes chemically more complex; in that way they contain a large number of different metals. These slags form complex non-ideal solutions (with possible formation of several immiscible slags) that can coexist with stoichiometric solids, solid solutions, mattes and molten metal depending on the bulk composition and process conditions. Predicting the outcomes of smelting and refining processes is becoming increasingly difficult. To assist in the optimisation of these metallurgical processing operations, a comprehensive research program is underway to develop accurate thermodynamic databases for these non-ferrous process systems.

Jan 1, 2019