Search Documents

By Y. Sasseville

"Niobec has been using vibrating screens and screw classifiers as a double stage classification in its grinding circuit since the very beginning of its operation in St-Honoré. Most of the other mineral processing plants around the world uses cyclones as the classification device in their grinding circuit. The difference between these two methods are well known in terms of capital cost and grinding efficiency but the differences in terms of the impact on the downstream processing stages are a lot harder to predict and are case specific. In the interest of lowering the capital cost of a future expansion project, Niobec decided to test the cyclones in its actual grinding circuit and evaluate their impact on the recovery of the downstream processing stages as well as the operating cost of the mill. We switched between cyclones and screens for 8 month in 2013 and early 2014 and we are now operating only with cyclones since march 2014.INTRODUCTIONThe Niobec mine and concentrator were built in the mid 70’s and at that time, the mill was processing 1 500 tons per day. Over the years, many expansion projects have brought the plant to 7 000 tons per day. Throughout the initial concentrator design and commissioning, screens have been chosen over cyclones because of their higher classification efficiency which is known to reduce variability and limit the fine generation especially due to a high undersize classification efficiency. Just like many other plants, fine particle generation is a major problem at Niobec because of its negative effect on downstream processing stages. In the interest of lowering the capital cost of a future expansion project, Niobec’s engineering team decided, 35 years later, to test the cyclones in its actual grinding circuit and evaluate their actual impact on the final recovery and the operating cost of the mill.The grinding circuit is separated in two lines which will be called Circuit #1 and Circuit #2 along this paper. Circuit #1 is, as you can see in Figure 1, composed of a rod mill and two parallel ball mills in closed circuit with screens and screw classifiers. The screens oversize are sent to the screw classifiers while the undersize are sent to the next processing stage. The screw classifiers overflow are both sent back to the pump box while their oversize streams return in their corresponding ball mills for further grinding. Circuit #2 is, as you can see in Figure 1, quite the same as Circuit #1 except it has only one set of screw classifier and ball mill. Figure 1 also shows the modification in arrangement each circuits went through to integrate the new cyclones. One of the ball mills in Circuit #1 now appears dotted because it can still be used but is not now"

Jan 1, 2015

By P. R. Day, W. K. Webster

"The introduction of large boreholes underground initially involved taking the techniques of open-pit bench blasting to the production stope, but with deeper boreholes and narrower stopes more controlled techniques must be developed in order to maintain good stope walls and prevent dilution of ore or structural damage to pillars due to blasting overbreak. The points discussed are drilling accuracy and drill pattern, the relationship between open-pit wall control and underground mining, the varied explosives products and initiation devices available, and some of the many ways that variations in loading, such as deck charging, etc., can produce desirable results.IntroductionThe use of large-diameter blastholes for underground mining began ten years ago and today they are widely employed in a variety of orebodies and stope configurations. These big blastholes, which range in size from 4.5 to 8 inches in diameter, were originally employed in the same manner ' as open-pit bench blasts; that is, the stope was silled out to full width and all holes were drilled vertical and parallel. This was suitable for competent, massive orebodies, however the popularity of the big drills saw their usage in more narrow stopes, often with poor ground conditions. The dipping orebodies and small drill sublevels resulted in inclined drilling.Today, there is full-ring drilling of 4.5-inch holes. Some 6.5-inch holes are drilled up to 350 feet deep. A 350-foot borehole may contain 6000 to 7000 pounds of explosive. The detonation of this size of charge weight within the confines of an underground stope can have considerable effect on the stability of stope walls and adjacent pillars. Obviously, precautions must be taken to minimize the damage which would result from the large charge weights possible with these big boreholes."

Jan 1, 1982

By Niklas Willemsen

Introduction to SVCs ? SVC = Static var Compensator ? Dynamic step-less control of reactive power without switching of passive components: ? Voltage control/stabilization ? Harmonics- and flicker mitigation ? Dip mitigation ? Main components: ? TCR (Thyristor Controlled Reactor) ? Tuned harmonic filters ? Control- and cooling systems ? Typical applications: ? Mine hoists ? Large mining complexes ? EAF, SAF, rolling mills, wind/solar farms etc..

Aug 1, 2013

By Walter F. Atkins

Fair market value, in the legal sense , is the price which a prudent and knowledgeable buyer and a prudent and knowledgeable seller, acting without constraint or compulsion , will agree upon to exchange an asset. In the ordinary commercial or engineering usage, the term may imply simply the market value or a reasonable and equitable price. The engineer evaluator who is called upon to express an opinion about the fair market value of an asset may be able to base his estimate on the sale price of similar assets or on the market values of stock. Frequently such indicators of value are not available and the evaluator must devise other means of appraisal. Mineral resource properties may be thought of as having value by virtue of the existing or potential ability to produce at a profit. Conventional procedures permit the computation of the present value of future revenues having due regard for the time value of money and the risks attendant upon the realization of the venture. Such computations have gained wide acceptance as a basis for the estimation of fair market value.

Jan 1, 1977

By C. Kennedy, S. Jensen

Traditionally, mineral processing plants are designed to achieve the highest recovery of valuable material with limited regard for the cost of managing waste products-both solid and water components. As an industry, we are confronting ever more stringent environmental standards and lower grade deposits requiring more intensive processing. The most profitable processing route can, in fact, lead to costly issues downstream. Issues or risks associated with waste management include water treatment and handling and storage of potentially acid generating material. The capital and operating costs of dealing with these issues are significant and should be considered as a consequence of plant design and optimisation. The authors of this paper are involved with a number of projects where process operation changes offer opportunities to mitigate risks associated with water and waste management. Examples of these changes will be discussed along with the estimated benefits to the value of the project and reduction of long-term environmental risks. Process changes include 1) the application of in-plant water treatment as opposed to dealing with the entire tailings management facility and 2) the potential to reduce metal leaching and acid rock drainage through the preferential liberation of carbonate minerals in the grinding process.

Jan 1, 2014

By L. Flett, S. Woods, C. Deredin

"Following a significant reduction in world Imperial Smelting Furnace (ISF) capacity from 2003 to 2008, a major optimization initiative was successfully carried out on the lead upgrading and bulk (zinclead) flotation circuits in the Brunswick Concentrator.This paper describes the process improvements that have taken place in order to reduce the quantity of bulk concentrate:•,Increase in lead upgrading rougher flotation circuit capacity•,Installation of a closed-circuit bulk regrind utilizing MillPebs and 150 mm Cavex hydrocyclones•,Installation of two additional cleaner flotation stages on the bulk circuit•,Optimization of the manipulated variables in the lead upgrading and bulk circuitsINTRODUCTIONThe Brunswick Mine (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The planned closure of the mine will take place at the end of the first quarter in 2013. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.A simplified flowsheet for the concentrator is given in Figure 1. The overall flowsheet involves SAG milling, secondary ball milling, selective flotation, and dewatering by thickening, filtering and drying. The complexity of the flowsheet evolves from the requirements for fine grinding and the production of four concentrates: zinc (sphalerite), lead (galena), copper (chalcopyrite) and bulk (sphalerite plus galena).Primary hydrocyclone overflow feeds the copper-lead aerator-roughers for flotation at pH 9.0 with soda ash. Plant xanthate (80-20 sodium isopropyl and potassium amyl) and AP407 are used as collectors in the copper-lead circuit. The rougher concentrate is directed to the copper-lead regrind circuit and the tailings are fed to the secondary grinding circuit. The secondary hydrocyclone overflow from the secondary grinding circuit feeds the copper-lead rougher-scavenger banks. Rougher concentrates are reground to a P80 of 28 µm prior to three stages of copper-lead cleaning. The first stage of cleaning is done in an open circuit with the tail reporting to the cleaner scavenger. The cleaner scavenger concentrate reports to the regrind circuit and the cleaner scavenger tail combines with the rougher/scavenger tail to feed the zinc circuit. The second and third stages of cleaning are performed in closed circuit with the cleaner tail being recycled to the copper-lead regrind circuit. The average final concentrate grades 23% Pb, 3% Cu and 704 g/t Ag, and is fed to the copper separation circuit."

Jan 1, 2013

By Jean-Claude LeRoy, Herman Keller

"INTRODUCTIONEROCON's work is the reclamation of mine wastelands. It has had considerable experience in particular in the reclamation of gold mine tailings in the Canadian Shield since the latter part of the sixties when most gold mines were closing down.A typical example is the famous Hollinger Mine in Timmins which produced $566 million worth of metal from 1910 to 1968 and had left behind some 56 million tons of tailings covering about 1,000 acres which were reclaimed on very short order and are now lush meadows of agricultural quality.To date, practically all gold mine tailings have been reclaimed once and for all by establishing a permanent, self-sustaining and maintenance free vegetation cover.RECLAMATION & THE MINING TOWNSThe first appreciation of people in a mining community where the tailings have been revegetated will be noticing one day the elimination of dusty conditions that used to arise formerly on every dry and windy day. In that respect, EROCON encourages not only vegetating the tailings but also the immediate surroundings of the mills and plants themselves at active mines. The elimination of windborne dust will result in an appreciable decrease in maintenance costs of plant and machinery and more pleasant working conditions for all."

Jan 1, 1975

By G. J. Ackland, K. Saksl, F. Brunke, M. Kohnke, B. Tegner, C. Siemers

The application of titanium alloys is limited to 550°C due to their poor oxidation resistance. It is known that the addition of niobium decelerates the oxidation of titanium alloys whereas elements like vanadium do not improve titanium’s oxidation resistance. The underlying mechanisms are not yet well understood. In the present study, different binary titanium-niobium and titanium-vanadium alloys as well as commercially pure titanium were investigated. Oxidation experiments were carried out at 800°C up to 288 hours followed by metallographic analyses to study the oxide layer morphology as well as the microstructure at the interface. Energy-dispersive X-ray spectroscopy mappings were used to identify possible changes in the distribution of the alloying elements. In addition, micro-focused hard X-ray experiments were performed to layer-wise analyse the phase composition in selected samples. As expected, the niobium containing alloys show a better oxidation performance compared to commercially pure titanium and the titanium-vanadium alloys. The oxide layer consisted of TiO2 and Ti2O3. Depending of the niobium content, a niobium-rich layer developed below the metal-oxide-interface minimising oxygen diffusion into the titanium matrix. Based on these results, the minimal niobium content needed for improved oxidation resistance was identified so that alloys of technical relevance can now be developed.

Jan 1, 2014

By Brian Hart, Roger St. C. Smart, James Francis, Mark Biesinger

"There are a number of challenges involved with the surface analyses of different mineral phases from process streams in a flotation facility. The first of course is to collect samples that are representative of the process and to ensure that they remain in a pristine condition prior to introduction into the instrument. In mineral processing, sample collection from the different streams is done on site and preservation involves simply removing oxygen from the sample by bubbling nitrogen or argon gas through the sample and snap freezing with dry ice.The second challenge in studying the surface chemistry of specific minerals is to find reliable methods of mineral phase recognition. In surface analysis of mineral particles confident mineral selection can be difficult with many multi-metal minerals (e.g. chalcopyrite, pyrite, sphalerite) and with precipitated, adsorbed, reacted and contaminant species in the outermost molecular layers.In this paper we show that principal components analysis (PCA) of ToF-SIMS data provides improvement in phase recognition, particle selection and associated variations in surface species. We will demonstrate, with specific examples, that this technique can be utilized to differentiate surface chemical factors promoting (hydrophobic species) or inhibiting (hydrophilic species) flotation.Species recognition based on the PCA method in a study of Cu transfer between chalcopyrite, pyrite and sphalerite mineral mixture clearly identified a statistical difference in copper intensities between the sphalerite and pyrite phases. A similar ToF-SIMS/PCA based study applied to concentrate and tails samples collected from the Inco Matte Concentrator demonstrated extensive CuOH and NiOH transfer between the chalcocite and heazlewoodite minerals. The statistical analysis has been able to confirm some mechanisms and deny others proposed to control recovery and selectivity giving more focus on the control factors.The ToF-SIMS PCA statistical analysis has elucidated differences in surface chemistries which illustrate the discriminating depressant action of adherent aluminosilicate (gangue) fine particles and adsorbed ions on the surface of sphalerite grains. In the flotation test concentrates, HIC conditioning resulted in the removal of these gangue fines thereby improving surface collector attachment efficiency, promoting a greater recovery of sphalerite."

Jan 1, 2007

By W. G. Johnson

"As we move into 1983, Canada is not only in a deep recession, there are major changes taking place.International competition is growing fiercer.Major core industries such as automobile, steel, mining, oil, agriculture, forestry, fishing, major manufacturing and others are just not expanding.If and when recovery comes starting in mid-1983, as many predict, don't expect industries to suddenly resume former growth patterns. It's just not possible.Companies, by necessity, are becoming lean and mean, and they are still in the process of reducing staff to meet changing times and conditions. Many of the staff now being released may never return to fulltime work with a single employer, particularly if they cannot measure up to more exacting performance standards and management expectations.There are clear cut instances of people who lose a job for reasons beyond their control. A merger, the loss of function, or a major reorganization sometimes creates casualties of people who were excellent performers. Such people can survive well, based on the tongue of good report and with some help from associates or others. However, even good performers often have difficulty in adjusting to the rigors of finding a new job and to become their own personal salesman."

Jan 1, 1983

By C. Blais, G. L’Espérance

Characterization of second phase particles is important with regard to their influence on mechanical properties of materials. Analytical electron microscopy offers the possibility to achieve complete characterization of inclusions. Complete characterization of inclusions means quantitative evaluation of their chemistry and the stereological parameters. A characterization technique based on integrated microscopy and involving scanning electron microscopy, image analysis and energy dispersive X-ray spectrometry is presented. A discussion of the use of transmission electron microscopy and electron energy loss spectroscopy is also presented for the characterization of very small particles and compounds (>100 nm).

Jan 1, 1998

By Timo Niitti, Antti Rinne, Janne Turunen, Sami Grönstrand

"This paper describes novel methods to enhance the flow dynamics of a mechanical flotation cell that can be applied to an existing installation. There are several reasons to alter the flow dynamics. The most common motivation is to improve the metallurgical performance of the cell, for instance, to improve the flotation recovery in particle size ranges that are normally difficult to recover.The flow dynamics enhancements are associated with the geometry of the rotor-stator area and additional features in the tank. The rotor-stator area has been modified to provide more concentrated turbulent kinetic energy or respectively more pumping efficiency with less attrition to the slurry. The tank can be fitted with various geometrical features, aimed to create a desired particle suspension profile. Depending on the targeted particle size range and application, badly selected or designed features can also have a negative effect on the metallurgical results.Besides new flotation equipment, the enhancements can be applied to existing flotation cell installations, thus enabling improvements in the mixing profiles, solids suspension, tank sanding and metallurgical performance of operating flotation circuits. Results of several tests carried out in existing plant operations are presented, concerning both flow variables and metallurgy.The common factor to above-mentioned enhancements is the use of modern computational fluid dynamics tools in the design phase, as well as the validation of the obtained CFD results in laboratory and production scale. Validated variables include mixing profile, power draw and local air hold-up.The paper demonstrates the effects of various flow geometries on the mixing profiles and metallurgical results of existing mechanical flotation cells. It shows how modern computational fluid dynamics analysis can be used to screen and select different approaches before carrying out costly trial-and-error experiments in plant scale."

Jan 1, 2006

? Founded In 1953 ? Mining growth of 83% since 2007 ? We produced over 1 million ounces of Au in 2012 ? We Forecast of 20% Au production in 2013-2015 ? We have paid a dividend 31 years consecutively. Terry Reid ? 1992-93 Electrical Technical, College ? 1994-95 On the job placement College ? 1998 ? Licensed Millwright, ? 2005-12 ? Maintenance Reliability Planner ? 2012- Present Business Process Owner

Aug 1, 2013

By Hugo Julien

According to OSHA 29 CFR Part 1910.119 (Process safety management of highly hazardous chemicals), Canadian Provincial Safety Standard Acts or Federal laws, the owner of stationary equipment (Boilers, stacks, piping, pressure vessel, etc.) should follow a complete inspection plan and follow an Integrity Operating Windows (IOW’s) adapted for each of them. Some important variables shall be included in the inspection plan such as specific damage mechanisms versus alloy used in the original design, process conditions, etc. Some North American’s standards exist, like the one listed in ASME PTB-2-2009, to help owner to create such inspection program. The new API RP 584, Integrity Operating Windows (IOW’s) can guide Mining & Metals owners to find out their specific IOW’s. Inspection frequencies are often described in the Jurisdiction Safety Acts such as the British Columbia B.C. Reg. 104/2004, etc. but often left in the owner representative responsibility (Bill C-21, federal Act to amend the Canadian Human Rights Act). Every deficiency should be repaired according to recognized Codes such as ASME PCC-2, etc.. If flaws not conforming to the original Code of construction are found, this article will introduce the Fitness-For- Service assessment principles to be able to accept it without any repairs.

Jan 1, 2014

"Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating various minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid, such as water or air (Wills, 2006).Spirals concentrators are one of the gravity concentration equipment used for beneficiation of minerals. Spirals are typically used for processing of fine minerals (-1mm) size fraction. The main operating variables for a spiral concentrator are the feed rate, the solids concentration, the wash water addition and the position of the cutters or splitters used to separate the tailings, middling and concentrate streams (Sadeghi, Bazin & Renaud, 2014).The aim of this study is to investigate the effect of feed rate, solids concentration and wash water on grade and recovery on iron ore material. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentration and feed rate. The wash water rate was also varied to establish the best washing rate. The splitter positions were kept constant. Optimization of these variables is expected to provide optimum conditions for a good compromise between grade and recovery.INTRODUCTIONSpiral concentrators are simple low energy consuming devices that separate minerals mainly on the basis of density. Spirals are widely used in mineral processing as a method for preconcentration and have proven to be metallurgically efficient and cost effective.Spirals have a wide application, they are used in iron ore processing, coal, gold, chromites, mineral sands, glass sands, and in soil cleaning.Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational forces, centrifugal force, hydrodynamic drag, and lift and friction forces (Kapur & Meloy, 1998). Apart from the forces acting on a spiral, the properties of the slurry flowing on a spiral including, solids concentration, feed rate and wash water also plays an important role in the separation on the spiral.The relationship between separation efficiency and feed rate was shown to be linear, with a decrease in efficiency at higher flow rates. Previous work on flow profile by Holland - Batt (1990) indicated that any increase in the feed rate to a spiral results in a greater part of the additional flow volume reporting to the outside of the trough. The flow on the outside of the trough becomes energized and consequence to that the heavy particles find it hard to settle and escape this region to the inner region. This effect has a high impact on recovery of heavy minerals, since any increase in volumetric flow on the spiral is not made available for recovery in the inner region of the spiral."

Jan 1, 2015

By Roger Payne, John R. Goode, Feng Gao, James Brown

The Eco Ridge deposit is located in the Elliot Lake mining camp in Northern Ontario, Canada. Between 1955 and 1996, the area produced more than 138,000 t (300 million pounds) of U3O8 and very significant amounts of thorium and heavy rare earths. Based on the NI 43-101 Preliminary Economic Assessment by Roscoe Postle Associates (RPA) dated June 2012, and the economic review by RPA as announced in Pele Mountains’ Press release dated September 12, 2013, the Eco Ridge Mine Project would extract and process 46 Mt of material to produce about 19,000 t (42 million pounds) of U3O8 and about 65,000 t of rare earth oxide (REO) over a 14-year life. This paper discusses process optimization studies including beneficiation and hydrometallurgical testwork. The proposed modified flowsheet includes the flotation and processing of 1) a pyrite concentrate, 2) a dominantly light rare earth elements (LREE) concentrate, 3) a concentrate containing most of the balance of the uranium and heavy rare earths (HREE), and 4) a relatively inert tailings.

Jan 1, 2014

"As mine head grades decline and orebodies become more complex, traditional mineral processing techniques and flowsheets to achieve saleable concentrate become more difficult to design and construct. Mines with lower quality concentrates or concentrates with penalty elements are particular under threat. The economics of these operations are far more susceptible to metal price, concentrate treatment terms and the availability of other, cleaner concentrates. Additional value may be realised for these orebodies through improved recovery by producing a low grade middling concentrate for further processing, in conjunction with a saleable concentrate.The most cost effective way to reduce impurity levels is to do so as early as possible in the mining value chain. Technologies such as fine grinding and fine particle flotation are well established as effective methods for impurity rejection in mineral processing. What is normally overlooked is how a hydrometallurgical process could also be integrated in the overall flowsheet to achieve higher overall recovery at the mill. In the base metals environment, this is mainly because hydrometallurgical processes are associated with production of metal or use of expensive and toxic precipitating agents once the minerals of interest are solubilised. These processes can be very expensive, particularly with rising power costs and poor economies of scale in capital costs associated with low production rates from middling streams.Glencore Technology (GT) has recent experience in the treatment of middling and low grade concentrate streams as well as tailings streams to compliment a concentrator flowsheet in a refractory gold and base metals setting. The value proposition is the isolation of a low grade middlings concentrate from the primary circuit or the tailings stream for upgrading to an intermediate product with an equal or higher grade than the primary concentrate to allow blending for sale. This allows plants to operate on a more favourable part grade-recovery curve while avoiding the expense of metal production. For existing operations this is particularly attractive since it can be added on with no process interruptions.Two case studies are examined showing flowsheets and costings to arrive at the value proposition of the GT low grade treatment flowsheet."

Jan 1, 2017

By R. A. Hill, J. D. Pitts

"Long distance slurry pipeline systems have been successfully trans-porting steam coal, iron concentrates, copper concentrates and limestone for an aggregate of nearly 60 years and nearly three billion ton-miles annually. A phosphate concentrate pipeline is nearing start-up and systems for coking coal, lead/zinc concentrates and fly ash are planned. The solids pipeline concept, first patented in the early 1900's and commercialized in the 1950's, is now a proven technology providing an economic, environmentally pleasing and safe method for long distance bulk transport.The challenge for larger tonnage and longer distance movements of solids, for traversing increasingly rugged terrain in grass roots mineral developments, for transporting untried materials and for shipping more economic forms of proven materials still remains. This has necessitated continued refinements and optimization of the technology. The economic and environmental incentives for slurry pipelines when compared to other transport alternatives has justified substantial activity in this area. The scope of planned systems in coal, iron and other minerals is indicative of the firm place slurry pipelines will have in worldwide mineral development.In this presentation, the state-of-the-art in long distance slurry pipelines is reviewed with a focus on major systems of interest to the mineral processing industry. An overview of new developments in the application of this concept is presented, and finally, a projection of the future of pipelines in mineral development both worldwide and in Canada is discussed."

Jan 1, 1978

By E. J. Sun

The ADS system was developed to reduce accidents related to haul trucks operating under low visibility conditions in surface mining and construction sites, which is based on the GPS, mesh-wireless networks, and the Google-Earth 3D graphic engine as the graphic interface and mine-mapping server. This system has the capability to pin-point and track vehicles in real time using a 3D interface, which is based on user-based AutoCAD mine maps using the Google-Earth graphics interface. All equipped vehicles are shown in a 3D mine map stored in a local server through a wireless network. When low visibility conditions are present, the system indicates available exit/escape routes for driver safety. The research results indicate that the ADS system potentially increases reliability and reduces uncertainty in open pit mining operations by customizing the local 3D digital mining map, constructing the truck 3D models, tracking vehicles in real time using a 3D interface and indicating available escape routes for driver safety.

Oct 1, 2009

By Lutz Markworth, Evren Ören

"The worldwide demand of ores and the depletion of the high-purity deposits make it necessary to recover ores in increasingly finer size fractions in the feed material. The flotation technology of more than 40 years old plants was not able to recover the ultra fine material. Those slurry tailings ponds now have the chance to be re-processed with PNEUFLOT® technology.The bubble sizes of different flotation technologies have a huge influence of the results especially regarding the recovery of the ultra fine particle sizes.PNEUFLOT® technology of HUMBOLDT WEDAG Coal & Minerals Technology GmbH in Germany was applied to ultra fine Phosphate, Copper and Platinum ores. The results will be presented in this paper.Conventional technology like agitator flotation has its limits in the flotation of fines due to turbulences in the cell. The position of the agitator influences the recovery of the fines. A deep impeller generates a higher froth zone. This helps to catch the medium fines. Due to the static head of the slurry inside the cell, compressed air is required for such cell designs.Column flotation is well known for a good selectivity without having in the first cell a good recovery. This leads to invest in several cleaning stages to reach an acceptable recovery. Further more, compressed air is required to generate the air bubbles to the flotation process, which are much bigger than with PNEUFLOT® technology applied.INTRODUCTIONHigh metal prices are actually the basis to invest in poor deposits or deposits with very fine intergrown ores which have to be milled down to ultra fine powders less than 60 micron. The liberation grade has to be determined by a mineralogical analysis. Polish sections have to be prepared and interpreted by using of a microscope. Figure 1 and figure 2 are showing polish sections of a platinum-nickel ore from Petchenga Nickel at Zapolyarni Mine in Russia. The head grades for rich ore are for copper between 0.05 – 0.15%, for nickel between 3 – 7% and for platinum group minerals approx. 0.15 oz/t. With an efficient flotation technology it can be upgraded to 20 oz/t."

Jan 1, 2009