Search Documents

By John A. Meech

"Oleic acid flotation of Mount Wright thickener underflow tailing material has been shown to be capable of increasing plant recovery by 3%. High levels of oleic acid addition (1.5 kg/t) are required, which limit the economic practicality of the system at this time. Nevertheless, from a technical viewpoint, the process is stable with respect to extreme fluctuations in oleic acid requirements, pulp pH and pulp temperature. Methods to reduce the average consumption of oleic acid need to be found. One technique that merits further testwork uses the ""piggy-back"" principle to float hematite fines with coarsegrained hematite particles.IntroductionWith most large-scale iron mining operations treating specular hematite ores, flotation is not often conside red a necessary processing step. The bulk of the iron minerals can be concentrated by gravity techniques and the generation of fines can be minimized because of the course- grained nature of the mineralization. Nevertheless, production of some fine material is unavoidable, and recovery of iron from this fraction by spirals is poor (10-30%).When the proportion of the iron in these fines becomes excessive, alternative methods to conventional spirals are considered(11), Many of the techniques that have been developed suffer from either poor recovery (e.g. the Reichert cones at 36010 recovery)(11) or low throughput rates (e.g. wet highintensity magnetic separation)(12), Flotation is often passed over because of excessive reagent costs, pollution problems and/or balling difficulties from the reagents used.However, of all the processes available, flotation can yield high recoveries (60-90%) at reasonable throughput rates with excellent process control features (reagent addition and/or cell level). The key parameter is reagent cost.This paper describes testwork on the use of oleic acid to float hematite from the fine fractions of the Mount Wright concentrator tailing. The concentrate product from this plant is directly shipped, so no balling problems exist. As well, oleic acid may be considered a lesser pollution hazard than many of the cationic collectors used in other iron ore flotation systems. A reduction in fine hematite slimes discharged as tailing into lakes may also reduce environmental damage."

Jan 1, 1981

By Shahram Tafazoli

ABSTRACT: This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By A. LA. Salama, D. B. Hyma

"The Western Research Centre (WRC) of CANMET located in Devon, Alberta, is a modern research facility offering services ranging from fundamental research to pilot plant investigations. Recently, a 0. 76 metre diameter by 7.9 metre high Flotaire column flotation cell was installed as a demonstration unit for Canadian coal producers. Because the column cell is intended to be used for research, development and demonstration, WRC recognized that additional sensing equipment and improved process control would be required to generate good data for subsequent column scale-up and engineering design.A low cost, personal computer based control system was, therefore, designed and installed. This paper describes the stepwise procedure in developing the control strategies, selection of system software and hardware, and installation and configuration of the system.Preliminary performance data on a western Canadian coal sample are also presented. Future testwork is planned on additional coal samples to expand upon existing database."

Jan 1, 1993

By J. Baz-Dresch

"The most cost-effective method of placement of the high strength fill used in the Cannon Mine' s overhand cut-and-f ill bench stopes was determined to be truck haulage. Constraint s imposed by the mine layout dictated the use of a truck which could dump its load in a fifteen-foot high drift. The Dux Teledumper truck was selected as the most suitable unit for this application based upon operational and maintenance parameters which included a telescoping, tilting dump box; large load capacity; and robust construction. Development of the truck continues through the cooperation between the manufacturer and user. INTRODUCTIONThe Cannon Mine is situated in the centre of Washington state, approximately midway between the cities of Spokane on the east and Seattle on the west. The mine complex is located three block s south of the Wenatchee city limits at the eastern base of the Cascade Mountain range.Asam era Minerals (U.S.) Inc., with 5I% ownership, operates the Cannon Mine. Breakwater Resources, Ltd. holds the remaining 49%.Annual paroduction is 520 000 tons per year, presently on a 21-shift per week operating schedule for both the mine and the mill.All production is presently won by overhand bench stoping with backfill. Stoping starts with 15-ft high by 24- or 30-ft wide sill cuts driven above and below a stope block . A drop rai se and slot are used to open a bench which is then slabbed toward the open slot. Truck-placed backfill is dumped into the mined - out stope from the upper sill cut. This stoping sequence is repeated until the top of the ore block is reached . The top sill cut is then tightly filled with backfill to minimize subsidence and to provide adequate roof support during extraction of the pillars.Mining equipment consists of hydraulic drills and rubber-tired, diesel scoops and trucks."

Jan 1, 1989

By P. A. Studemeister

"A trondhjemite stock intrudes a volcanic sequence that has massive sulphide lenses and that is metamorphosed to the greenschist facies at Gutcher Lake, 25 km north of Wawa, Ontario. The stock is 4 km2 in plan and is partly enveloped by an aureole of chlorite-epidote-amphibolehornfels up to 1 km wide. Within this contact aureole, biotite is partly pseudomorphosed by chlorite;epidote and hornblende are mottled by chlorite, calcite, plus quartz; albite has 0% An to 8% An; and hornblende porphyroblasts have actinolite rims. The stock has chlorite pseudomorphous after biotite; and feldspar is mottled by white mica plus calcite and has a clear rim of albite. Fractures filled with quartz, calcite, ankerite, chlorite, white mica, pyrite, and native gold cross-cut the stock and its hornfels aureole. These gold-bearing veins are enveloped by foliated rocks with quartz, calcite, white mica, and chlorite that grade outward from the veins into trondhjemite or hornfels.The stock, emplaced into a submarine volcanic series, emanated heat that caused seawater to convect and formed a contact aureole of hornblende hornfels. The stock eventually intruded its aureole and this culminated with regional metamorphism to the greenschist facies. Regional metamorphism hydrated the stock and its hornfels aureole. Native gold precipitated with quartz along fractures from metamorphic flu ids in response to cooling and wallrock hydration. exploration for this type of gold deposits should focus around felsic intrusions that have albite and that have contact aureoles retrograded by regional metamorphism."

Jan 1, 1985

By Norman J. Tienkaivip, Christopher J. Preston

"This paper describes the use of electronics for physical measurement and computer analysis in both open-pit and underground mining operations for the ultimate purpose of optimizing production blasts. Techniques in monitoring single borehole blasts using both pressure and vibration sensors to establish in-situ dynamic rock properties are outlined, including characterization of multiple borehole production blasts with regard to stress generation.Once field derived measurements are computer analyzed, they are channelled as input parallel to other data, such as the explosives thermochemical performance properties generated by a sophisticated computer program called ""HT-65"" into BLASPA . BLASPA, a blast simulation computer program, then couples these input with a mathematical model which defines the blasting processes. Aspects such as the blast geometry, explosive loads and distribution, hook-up, and costs are studied. The final output table gives specific blast performance or quality factors for each blast procedure. These results are then easily compared and rapidly optimized to achieve maximum performance at lowest blasting and drilling cost."

Jan 1, 1984

By L. C. Kitchener, K. Vollenwyoer

"This paper describes the development of an automated, 70-ton capacity, underground electric trolley truck at Inco Ltd. The purpose of the project is to provide a high capacity and high productivity haulage system to suit continuous loader applications in existing mining horizons where conveyor belt application is not immediately practical. IntroductionWith the start o f a program by Inco in mid-1983 to develop a continuous loader for bulk mining of our hardrock orebodies, the need for a rapid ore transportation system was recognized to match the increased extraction rates planned. Two methods were investigated, truck haulage and conveyor belt. As a result, a conveyor belt system has since been designed and installed with a continuous loader at Stobie Mine and an electric truck has been designed, fabricated and assembled, with shop testing underway. This paper deal s with the latter project. BackgroundMany existing mining horizons which could utilize continuous loaders do not have the straight runs required for conveyor belts. In these situations, truck haulage would be the only alternative of the other transportation methods that would be practical. In order to match the high productivity potential of the continuous loader, however, a more efficient trucking system is required than would be available with conventional diesel powered trucks or with electric truck designs commercially available, or under development. A higher capacity truck and an automated operation is necessary so that the application of additional units to suit increasing haulage distances matches loader output without reducing over-all productivity because of the need for additional operators.A first effort to work with a major electrical manufacturer was unsuccessful and resulted in a project delay of almost one year. In November 1984, an investigation into the concept was reinstigated with UTDC, and an agreement to start design was reached in April 1985."

Jan 1, 1988

By Shahram Tafazoli

This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By Shahram Tafazoli

This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By H. A. Steane

THIS BRIEF PAPER presents the information available on the use of Dorrclon?is in the middling re-grind unit at the lead-zinc mill of Canadian Exploration Limited. The plant throughput is 1,650 tons per twenty-four hours. The flotation feed is ground to 60 per ?Cent passing through 200 mesh. It contains some composite 11articles of sphalerite in calcite, and these reported either in the final zinc concentrate, thus lowering the grade, or in the tailing, with loss of zinc. The re-grind unit was set up in the zinc flotation circuit to liberate the sphalerite from these middling particles, to raise the grade of concentrate and improve recovery. Grinding through 325 mesh should give substantial liberation of locked sphalerite. The middling regrind unit consists of two Dorrdones and one ballmill arranged as shown in the -accompanying flow-sheet. The Hardinge ball-mill, size 7 ft. x 36 in., was free for this use as a result of recent plant expansion. The two Dorrclones were purchased, and the necessary pumps and pipe lines were installed to complete the regrind unit. The unit has been developed over a period of two years by several steps and various flow schemes until reaching tl1e present flow scheme. These steps are not elaborated here, because the changes were made to determine the best product to work on for flotation metallurgy, and not because of the Domrolone classifying ability.

Jan 1, 1956

By Richard J. Kolada, Ian R. Muirhead

"This paper reports on a CANMET-funded examination of less conventional underground coal mining methods. These methods are documented and those that show the most promise for application to western Canadian conditions are discussed in detail.IntroductionIn recent years, mining considerations and economics have encouraged a transition from underground mining to surface mining. However, a change in market conditions or the development of superior underground mining methods may reverse this trend . Should this happen, the industry must be quick to respond and have information available on the latest developments of underground mining technology. In time, deposits of high-quality coal, which are easily accessible to surface mining, will be depleted and a change to underground mining methods will require consideration. The economic transition point between surface to underground will be a major determinant in maintaining a competitive edge. For these reasons, it is important to keep abreast of improvements in underground mining methods. To meet this objective, CANMET awarded a research contract to Monenco Consultants Limited, to investigate unconventional underground mining methods that show a potential for western Canadaoi. This paper presents the results of this investigation."

Jan 1, 1988

By D. H. Wilton, C. I. Godwin, A. J. Sinclair

"A computer-based drill core logging system used to examine computer-based drill core logging system used to examine copper mineralization hosted in volcaniclastic rocks at the Sustut deposit, in north-central British Columbia, has many advantages over conventional logging. A relatively simple format for recording geological information allows complex, but significant, geologic parameters to be recorded consistently, accurately and quickly. This allows graphical presentations and statistical interpretation of the data that lead to rapid and detailed analyses of the control and distribution of copper mineralization at the Sustut deposit.Ore mineralization is concentrated in lens-shaped bodies and is zoned from native copper cores through chalcocite, bornite and chalcopyrite to a margin containing pyrite. Chalcocite, the principal mineral, occurs mainly in volcaniclastic agglomerate characterized by a specific grain size, a narrow range of matrix and fragment proportions, and a specific sorting.IntroductionWe report here a case history of the practical application of a detailed computer-based drill core logging system applied to the Sustut copper deposit of Falconbridge Nickel Mines Ltd. The Sustut deposit, containing a few tens of millions of tons of ore grading slightly more than one per cent copper (Church, 1975), is in north-central British Columbia about 875 km north of Vancouver. The deposit is contained in volcaniclastic sedimentary rocks of the Upper Triassic Moosevale Formation, which is within the upper part of the Takla Group (Monger and Church, 1977) of basic volcanic and associated sedimentary rocks. Takla rocks occur along the eastern fringe of the Intermontane Belt in the Canadian Cordillera (Sutherland Brown et al., 1971). The deposit consists of concentrations of copper sulphides, native copper and pyrite within pods and lenses parallel to bedding in the host sedimentary rocks. These sheet-like deposits exhibit a mineral zoning from pyrite at the fringes successively through chalcopyrite, bornite and chalcocite to native copper at the core (Wilton, 1978; Wilton and Sinclair, 1979)."

Jan 1, 1980

By M. S. Greenfield, E. Cocchiarella, S. Chubbs

"At Dofasco sNo.4furnace a variation of the basic oxygen steelmaking process, Klockner Oxygen Bottom Maxhutte (K-OBM), is used to produce steel. Large amounts of hot gases and particulate are evolved during the oxygen blowing phase. A quencher and a venturi scrubber are used to collect over 99.5% of the particulate. In 1990, the authors investigated the effect of foamy slag on the particulate emissions from the furnace. The amount of lime added early in the oxygen blowing cycle was reduced, making the slag more viscous and foamy for a six minute period. Instantaneous particulate emissions were monitored throughout the blow by analyzing quencher and venturi scrubber water samples. Particulate emissions were reduced up to 59% during the foamy slag period.IntroductionThe reduction of the amount of waste generated or control of emissions at source is at the top of the ""3R"" hierarchy of waste management (Reduce, Reuse, Recycle). Process and operating practice changes are often the most economical ways to control emissions. At Dofasco, they investigated the effect of operating practice changes, specifically the formation of a foamy slag, on particulate emissions from steelmaking furnaces. They wanted to determine if a foamy slag changed the quantity and nature of the fume evolved from the K-OBM furnace over the oxygen blowing phase.The Basic Oxygen Steelmaking ProcessesThe basic oxygen steelmaking process (BOP) generates large quantities of very fine metal oxide fume during the production of steel. In this process, scrap steel and molten iron (hot metal) from blast furnaces are charged into a steelmaking furnace. Then pure oxygen is injected and a lime flux added . The oxygen reacts with carbon dissolved in the molten iron to form carbon monoxide. Oxygen lances can have secondary nozzles which introduce oxygen above the bath. This secondary oxygen, known as post-combustion, bums some of the carbon monoxide radiating the heat back to the bath. Particulate and gases rich in carbon monoxide are ejected from the furnace during the oxygen blowing phase and are collected by a gas cleaning system. Typically, more than 99.5010 of the particulate is scrubbed from the gases by high energy venturi scrubbers or electrostatic precipitators. The oxide sludge or dust collected may have elevated zinc and lead which is unsuitable for recycle to blast furnaces. Due to the presence of these undesirable elements, treatment and disposal of steelmaking oxide dust is difficult and costly."

Jan 1, 1993

By Raja V. Ramani, Sukumar Bandopadhyay

"The dispersion of diesel contaminants into the mine atmosphere is a variant of general class of diffusion-dilution problems relevant to underground mining practice. The equipment operations in underground mining are characterized by different activities with different time duration s, i.e. varying duty cycles. Therefore the volume and quality of diesel emissions and consequently, instantaneous concentrations are quite variable. Design of mine ventilation systems under these conditions becomes complex. In this paper, the development and use of mathematical models of mine production system, the engine exhaust air quality and engine exhaust transport in the design of ventilation system are discussed.IntroductionThe turbulent diffusion of suspended matter in an atmosphere is not only a topic of considerable intrinsic interest to the mathematical physicist and meteorologist, but also a problem of great practical interest. Release of particulate matter into the atmosphere at large has created o ne of the acute problems of the present day. Pollution of environment by industrial and domestic smoke, fumes and grit is widespread and has necessitated extensive studies in order to determine the concentration and distribution of pollutants in various areas. Pollutants discharge from stacks, whether chemical or radioactive, give rise to similar, but more localized, problems. The laws which govern turbulent diffusion in the atmosphere are also applicable to the study of the diffusion of toxic gases and the deposition of radioactive dust from nuclear explosion.The dispersion of diesel contaminants into the mine atmosphere is but a variant of a general class of diffusion-dilution problems relevant to underground mining practice. Most of the mine air pollutants, such as respirable dust, methane, diesel exhaust, and blasting fumes are produced in the face areas and haulage ways. Understanding of their dispersion in the mine airways is important to calculate their concentrations. In this paper, the development and use of mathematical models of mine production system, the engine exhaust air quality and engine exhaust transport are discussed. The over-all objective of this research effort is to evaluate the impacts of dieselization on production and ventilation systems and to aid in mine planning and design, as shown in the flow model in Figure I."

Jan 1, 1983

By G. Robert Guillet

"Ontario enjoys the advantage of its proximity to the large industrial market of northeastern North America. Together with Quebec and fifteen nearby U.S. states, an industrial base of more than half the total for both countries is provided by a population of 100 million.Mineral fillers such as barite, calcium carbonate, kaolin, mica, silica and talc are of major importance in the manufacture of paper, paint, plastics, rubber, vinyl tile, carpet backing, putty, caulks, sealants and adhesives. Ontario has all of these minerals, but domestic production falls short of demand in some cases, and mica and kaolin are not produced at all.This paper reviews the market and outlines the distribution of the major filler-consuming plants of northeastern North America. It also identifies the principal producers of filler minerals in the United States and Canada.IntroductionOf all the uses for industrial minerals, mineral fillers are probably the least understood. Originally used primarily to add low-cost bulk to a variety of commodities without seriously affecting their properties, filler minerals have become essential components that enhance and extend the properties of their hosts. Hence the term ""extender"" which, for all practical purposes, is synonymous with ""filler"". Today, fillers and extenders are not solely low-cost additives, but ingredients that provide essential characteristics to the products they fill.The major markets for mineral fillers are paint, paper, plastics, rubber, adhesives and floor coverings. But there are many others: putty, pesticides, wire and cable coatings, caulking and asphaltic compounds, oilcloth, wall-paper, joint cements, inks, sealants and many others. Barite, calcium carbonate, kaolin, mica, silica and talc are among the more important filler minerals discussed in this paper, but there are at least a dozen others. And the increasing practice of coating the mineral surfaces with certain coupling agents or metal stearates is constantly expanding the range of characteristics and hence the marketing opportunities.Whiteness, particle shape, fineness of grind and cost are the principal considerations in selecting a filler, but other characteristics such as weight, opacity, hardness and chemical inertness may be dominant considerations in specific applications."

Jan 1, 1987

By G. Girard, A. Larouche, J. Colbert, G. Doyer

"The Direct Chill (DC) casting process uses water to extract heat from molten aluminium and helps to control the solidification process. Many factors such as the water flowrate, water distribution around the mould and water impingement angle have significant impacts on the solidification process. It has been noted that the chemistry variation of the cooling water is also an important factor that has a major impact on the presence of defects on the ingot. A significant change in the water quality can produce defects on the ingots such as cracks, bleedouts, or runouts. Understanding the impact of water quality variation on ingots is therefore essential to ensure good ingot production and reduce defects. This paper aims at describing a new approach to follow the variations of process water quality over time. It is an original and innovative method, which is still under progress. A water quality and stability index (WQSI) is under development to evaluate changes in the water composition based on water physico-chemical parameters. The index is calculated by comparing each of the actual parameters with historical values previously modeled by a statistical law. It is a dimensionless number having an adjustable weight factor for each parameter. The positive or negative contribution of each parameter, with respect to the water cooling capacity, is taken into account to calculate the WQSI. The current selection of parameters is based on knowledge from the literature as well as on empirical experience. When the developed tool will be mature, it could be used to track water variations upon time and anticipate problems, enabling proactive actions to ensure good ingot production.INTRODUCTIONFor many years, the impact of water chemistry on heat transfer, during DC casting, has been of great interest in the aluminum industry. Several papers have been published to demonstrate the correlation between water chemistry and heat transfer (Yu, 1985), (Gildemeister, 2014). Although numerous studies do present the effects of water parameters (i. e. hardness, conductivity, oil, and grease…) on cooling capacity under controlled experimental conditions, they do not reflect the strong interactions between the parameters and variations present in a casting center. Wells and Cockcroft also demonstrated that laboratory based studies are not fully representative of real heat transfer in an industrial casthouse, there are too many factors involved (Wells, Li, & Cockcroft, 2001). In this context, it becomes very difficult to obtain a quantifiable relationship between the capacity of water to cool the ingot and ultimately the performance of the cast."

Jan 1, 2016

By Lynne Bowen

"On the da y shift in Number One Mine at Nanaimo on Vancouver Island, on May 3, 1887, William Griffiths, a coal miner with many years experience, fired a shot to advance the face of the crosscut. A flame ran out for a distance of fifteen feet along the roof and then extended up the slope for ten to twelve feet, and although many would have called this a blowing out shot, Griffiths said it was just a feeder. ""A blower"", he said, ""would have caused an explosion."" 1There was no explosion. Griffiths reported gas and the area was cleared for three hours and then work resumed. When the shift changed at 3:00 p.m., the fireman reported all places clear of gas and the ventilation good.2The ventilation in Number One Mine was the best anyone had ever seen. The air in the mine was almost too cold. The current was so strong that it sometimes blew out the flame on the miners' fish oil lamps. It delivered five to six hundred cubic feet of air for every man and animal working in the mine. The law required only one hundred cubic feet 3The miners considered Number One to be relatively safe. The manager was proud of the mine and its up-to-date equipment"". Recently, there had been reports from France and America about the explosiveness of coal dust, but the manager did not think his mine was sufficiently dusty to be dangerous.5 The dust lay thick on the floor of the mine. Sometimes when a shot was fired the dust rose in great clouds. When a miner was shovelling it, the dust would billow up and be carried off by the current of air. The dust was also in the roof and in the stopings, put there intentionally to fill up the spaces and prevent the accumulation of methane gas."

Jan 1, 1992

By Jacque Turgeon, Gontran Foy

"The Mineral Research Centre of the Quebec Department of Energy and Resources has worked extensively on the development of a dry process to extract pure mica flakes from a phlogopite ore. The liberation of mica from the gangue is effected basically by impact crushing, and the ground ore is screened into several fractions, each having a fairly narrow range of grain size. Each sized fraction is then fed to an air separator where heavy grains are separated from light flaky grains. Heavy fractions are returned to hammer mills where gangue minerals are ground finer and blocky mica particles are exfoliated. A second stage of screening is performed and each fraction is sent to an air separator. This sequence is repeated until mica products are virtually free of gangue. These different fractions are then treated in a cage mill in which mica flakes undergo a more orderly exfoliation along cleavage planes. The ground mica is again submitted to a final screening stage, after which each fraction constitutes a final commercial product.This process permits the recovery of about 70% of the mica contained in the ore. The over-all process will be described along with technical details of each unit operation. Recent work on a wet grinding method to produce very fine mica will also be discussed.IntroductionRecords of production of mica in Quebec date back to 1886. Production has been more or less continuous since that time, with peak activity during the war years. Production was interrupted in 1966, but started again in 1972 when Marietta Resources and Laviolette Mining and Metallurgical Corporation started their joint operation in Canton Suzor, northwestern Quebec. Mica deposits of more or less importance exist in different parts of Quebec, of which three have attracted attention in recent years: the Canton Suzor deposit, the Canton Lamy deposit and the Canton Chasseur deposit. The Suzor orebody was first identified by Carl Faesler in 1936, who described the rock as ""brown biotite in flakes half an inch in diameter, with interstitial augite, apatite and feldspar""."

Jan 1, 1982

By R. Le Houillier, M. Nagamori, A. J. Plumpton

"Asbestos tailings are a typical serpentine, hydrated magnesium silicate, consisting primarily of antigorite and a few per cent of unrecovered fibrous chrysotile. Serpentine has unique thermal properties in that dehydroxylating calcination at 600 to 700°C can yield an amorphous structure in which most of the magnesia is liberated from the original bond with silica and thereby rendered chemically active. The amount of activated magnesia can be quantified by selective leaching with a weak acid such as acetic acid. Many wet processes have been proposed to extract magnesium values from calcined or natural serpentine by means of various acids and their ammonium salts. However, the only commercial utilization of serpentine today is found in dry processes such as the production of fused magnesium phosphate fertilizer .The present paper reviews the physical chemistry of the dehydroxylation of serpentine and also various wet and dry processes in order to provide a general view regarding the chemical transformation of asbestos tailings.IntroductionAsbestos fibers occur as chrysotile, a serpentine polymorph. More than nine tenths of mined asbestos ores consist of massive non-fibrous serpentine, primarily the polymorph antigorite, which is discarded as tailings after fiber extraction. For many decades, Quebec has been a world leader in the production of asbestos fibers. As a result, colossal tonnages of serpentine have accumulated in the Eastern Townships'!'. Serpentine minerals are found in large deposit s throughout the world, and significant research efforts have been made, particularly in Japan and the USSR, mostly in attempts to extract magnesia or silica values therefrom.The chemical composition of serpentine (chrysotile and antigorite) may be ideally expressed as Mg3Si2Os(OH). which corresponds to 43.7% MgO and 43.3% SiO2. Natural serpentines often contain a few per cent of Ni-bearing magnetite and other impurities, and therefore the contents of MgO and Si02are both about 40% or lower.Serpentine (hydrated magnesium silicate) is virtually insoluble in weak acids. However, when dehydroxylated under controlled conditions, ' it decomposes to an amorphous state in which magnesia and silica are isolated and chemically active. The magnesia so activated is readily soluble in weak acids. This unique characteristic of calcined serpentine, first discovered in 1942,, has since attracted the attention of innumerable researchers, whence many processes have been proposed."

Jan 1, 1980

By K. M. Ed

AN explosive is a solid or liquid substance which, when fired by some means, changes into a gaseous product occupying a volume very much greater than its original volume. The great speed at which this change takes place causes the explosive to exert a sudden blow on adjacent material. It is this action which is effective in blasting operations when the explosive, confined in a shot-hole, is fired. All explosives are similar in one respect, in that the change into the gaseous state is accompanied by the production of hot gases or flame. This results from the rapid combustion of the solid or liquid ingredients. Ex-plosives differ greatly, however, in the speed at which the reaction takes place. Black blasting powder, for instance, reacts comparatively slowly, hence the flame persists for an appreciable length of time. High explosives, on the other hand, react much more quickly; consequently, the flame is of much shorter duration. In 'closed-light' or 'gaseous' coal mines, the use of ordinary explosives is generally prohibited, due to their inherent ability to ignite gas or coal-dust by reason of the flame which they produce when fired. For instance, black blasting powder, which produces a flame of long duration, is not ordinarily considered safe to use in such mines; neither are ordinary dynamites, as their flames, while shorter than that of black blasting powder are, nevertheless, of sufficient temperature and duration to cause ignition of fire-damp or coal-dust. For this reason, specially formulated high explosives, called 'permitted' explosives, should invariably be used in such mines.

Jan 1, 1940