Search Documents

By H. L. Ramandi, P. Moore

"The corrosion of support bolts in underground mines has become an increasingly prevalent issue over the past two decades. With an increase of premature failures due to Stress Corrosion Cracking (SCC), it is evident that understanding the environmental factor influencing the cable bolt corrosion is critical for maintaining effective ground support hence the safety and productivity of underground spaces. Experimental testing of rock and cable bolts were accomplished in a variety of packings, including saturated clay, saturated coal, mine water and grout/cement to investigate their corrosion behaviours. Water samples were obtained and analysed for pH and electrical conductivity (EC) during the experiment. After a period of 76 days the bolts were retrieved and analysed visually. Primary factors were found to be the presence of geological materials and the aeration of the bolts, i.e. the vicinity to air and air flow, while secondary factors were observed to be pH levels and EC. It was also found that the coal/clay interfaces and the water/grout/cement interfaces are non-relevant to corrosion of rockbolts and cable bolts. The proposed framework can be applied to other reinforcement materials used in underground spaces for improved understanding of corrosion environment.INTRODUCTION Rock bolts and cable bolts are the major reinforcement elements used in mining industry to improve the rockmass properties for safe and productive mining. They are normally used to pin large beams or blocks of rock in underground mines to stabilise the rockmass in the roof (strata) against collapse. The rockbolts are typically low cost hot rolled rebar while cable bolts are composed of strands of wire, normally wound together around a central king wire (Hyett and Bawden, 1993; Vandermaat, 2014). The typical length of the bolts in underground mines is 2.4 m and 4–12 m for rockbolts and cable bolts, respectively (Vandermaat, 2014; Windsor and Thompson, 1997). Cable bolts are much more flexible and usually offer a much higher load capacity than rigid rockbolts. Their increased length and flexibility allows cable bolts longer than the height of a roadway to be used in underground mines."

Jan 1, 2017

By M. O. Pekguleryuz, D. S. Aydin

The high temperature oxidation and ignition resistance of Mg-(0-6) wt% Nd alloys have been investigated via isothermal and continuous heating experiments conducted in air atmosphere. Alloy composition is observed to be effective in low levels (~ 0.5 %) in the ignition temperature (Ti) of the alloys; the Ti of pure Mg increased from 630 °C to 770 °C with 0.5 wt% Nd addition. However, no noteworthy improvement was achieved with further additions up to 6 wt% Nd. The initial microstructure was observed to determine the oxide structure on the surface due to the differing oxidation behavior of the phases (a-Mg + Mg12Nd intermetallics). It has been found that the formation of a Nd-depleted region at the subsurface due to extensive Nd oxidation at the oxide/intermetallic interface lowers the protective ability of the oxide scale.

Jan 1, 2015

By M. Mahfoud

The effect of grain refinement on the tensile and fatigue crack propagation behavior of sand cast magnesium alloy AM60B has been investigated in the present study, C2Cl6 in the amount of 0,3% was used to grain refine the melt, The fracture toughness tests were conducted in laboratory air at room temperature (25°C) using a sine-wave cyclic frequency of 20Hz and a load ratio of R = 0,1, The response in the Paris's regime and the critical stress range were determined, Preliminary findings have shown that C2Cl6 has a significant effect on both the tensile properties and fatigue crack propagation of the alloy tested, Grain refinement increased both the yield and ultimate tensile strength by more than 46%, and decreased the crack growth rate from 2,7 to 1,4 MPa Vm , However, the grain size seems to have a smaller effect on threshold stress intensity factor range. The fracture surfaces of specimens were examined optically and under the scanning electron microscope (SEM) to determine the relationship between grain size and fatigue properties.

Jan 1, 2005

By Chris Brothen

The introduction of new technology in mine operations has provided real opportunities for increased efficiencies and production gains which translate into enhanced profits. Computing and network technology usage has become integrated into surface mining operations and on average these investments in technology have proven beneficial for efficiency and productivity improvements. Embracing new technologies however, does not guarantee positive results. The expectations or improvements derived through the technology must be confirmed and clarified well before implementation. Tire Pressure and Temperature Monitoring Systems are an excellent example of an existing technology that can provide full time automated performance measurements of tires operating under harsh conditions and environments. Prompt warnings or alarms signaling when a tire has exceeded operating capacities will provide savings through lowered maintenance costs and increased productivity. To truly quantify the projected savings in tire life, fuel consumption, and increased levels of production, all costs associated with the technology, both direct and indirect must be considered. Apart from the initial cost of the system implementation, ongoing maintenance and support costs must be considered as well as the costs of system integration into existing mine operations

May 1, 2008

By George J. Simandl, Donald F. Gunning

At the beginning of the 20 century, British Columbia produced a wide variety of quality dimension stone products for both domestic and foreign markets. The industry flourished until the 1930s when most of the producing quarries closed as a result of the Depression. During the 1990s, British Columbia experienced the resurgent North American dimensional stone production trend. The industry benefited from increased prospecting activity and from substantial new investment in processing equipment, particularly in the granite sector. These activities resulted in new quarry developments, the reopening of abandoned quarries such as on Granite and Fox Islands <www.quadrastone.com>, and a renaissance in downstream value-added activities. British Columbia has reestablished itself as an important, reliable and innovative source of high-quality stone products.

Jan 1, 2001

By V. Loya

Metallic foams (MF) are relatively new materials with a combination of attractive properties (permeability, high surface area, thermal and chemical stability, etc,), They can be produced from different materials and can be manufactured using various processes, Due to their unique properties, they find applications in different sectors of engineering, such as energy absorption, filtration, heat dissipation, etc, For many applications, the permeability is an important parameter to characterize and optimize, Most of the recent literature on the subject studied the permeability in the low velocity range. The present study was carried out to have a better understanding of permeability for greater velocity ranges, An equipment was designed and built for this purpose, Pressure drop measurements were made across the thickness of open-cell nickel foams, Pore and window sizes were measured by image analysis on SEM micrographs, The experimental results are in relatively good agreement with the Hazen-Dupuit-Darcy model (R2>98%), The permeability is affected by pore size, porosity and the normalized projected area of the connecting pores (ie. windows).

Jan 1, 2005

By J. Warner, K. A. Hughes, P. E. R. Blanchard, J. Esslifie-Dughan, J. W. Reid

Tailings management plays an important role in reducing the environmental impact of Orano Canada’s uranium mining operations in Northern Saskatchewan. Uranium ores mined from Northern Saskatchewan are often associated with large amounts (10-20 wt%) of other harmful elements, such as arsenic and nickel. The JEB Tailings Management Facility (TMF) located at McClean Lake, Saskatchewan is designed to prevent potentially harmful water-soluble elements, particularly arsenic, from contaminating the surrounding environment by promoting the formation of water-insoluble minerals. It is therefore important to determine which arsenic-containing mineral species are present in the TMF and how they evolve over time. Researchers at the Canadian Light Source (Saskatoon, Saskatchewan) were successful in identifying the arsenic mineral species present in tailings samples collected from the TMF in 2013 using X-ray absorption near-edge structure (XANES) spectroscopy. XANES analysis verified that the majority of arsenic species in the TMF existed as amorphous and crystalline ferric arsenates with minor amounts of arsenite and arsenide species. Herein, XANES is again used to analyze a new set of tailings samples collected from the TMF in 2018, specifically focusing on the difference in the distribution of arsenic species in old and new tailings.

Jan 1, 2020

By S. R. Steinacker, H. Schnideritsch, J. Antrekowitsch

Primary copper industry flue dust plays an increasingly important role in the creation of matte and slag. From a thermodynamic point of view, the chemically formed section of fine particles play a techno-logically interesting role in comparison to the mechanical carry-over. Here, the volatilization and the sub-sequent condensation in the off gas system lead to a characteristic distribution of the contained elements which are represented by various compounds of desired metals like zinc and lead. On the contrary, certain undesired components such as arsenic, bismuth and cadmium accumulate within the product as well. This paper describes existing models and theories concerning the formation of flue dust in the copper smelting process and presents a thorough investigation of the physico-chemical fundamentals by verifying assump-tions with thermodynamic calculations. By fully understanding the formation patterns at different stages and temperatures within the process, better knowledge for flue dust in the first step of the pyrometallurgi-cal copper smelting can be obtained - hence leading to new ideas and incentives for the following stages in the copper production cycle.

Jan 1, 2015

By J. Stachulak, M. Scobie

"This paper addresses the occurrence and indicated causes of conveyor fires in North American and European underground mines. Some significant convey or fires which have been experienced in recent years in Canadian hardrock mines are then reviewed. The nature of existing conveyor monitoring technology is considered in the context of such fire hazards. Experiences with new monitoring technology recently installed at several conveyor sites at Inca Ltd. mines are then reviewed.IntroductionFires associated with conveyors have long been recognized as a serious hazard in underground coal mines. Recently, however, there have been some significant conveyor fires in Canadian underground hardrock mines. These offer important evidence as to the nature and causes of potential hardrock mine fifes. They also warrant attention with a view to improving over-all mine design, ventilation and emergency preparedness.In addition, a new era in mine communications and monitoring technology has been entered which should offer improved capability to protect against such fires. This paper was motivated by the need to understand the causes and mechanisms of conveyor fires in order to improve their safety. This should be possible through implementing more effective monitoring systems, as well as improving conveyor design. Underground mines are becoming more intensively mechanized, with less human surveillance of equipment and a greater dependency on remote monitoring systems."

Jan 1, 1992

By T. Narita

The diffusion barrier coating system (DBC system) was designed to suppress interdiffusion between alloy substrate and coatings in addition to ensuring slow oxide growth at high temperatures. In this report the concept of the DBC system will be introduced, and the results obtained for various heat-resistant alloys are presented. In this DBC system the s-phase of the Re-Cr-Ni system was selected as the barrier and is formed by electroplating Re-Ni and Ni films from aqueous solutions, followed by Cr and/or Al pack cementations. A typical DBC system consists of Ni-base superalloy / triple s-Re based alloy layer / ?’-Ni3Al and/or ß-NiAl (with or without Pt addition) / a-Al2O3. It was found that the DBC system maintained its structure for long time exposures because the s phase has tie-lines with the ? and ?’ alloy substrate and the ?’ and/or ß coating. The s-Re based alloy can suppress both the inward Al diffusion and the outward diffusion of alloying elements. The DBC system was successfully applied to various heat-resistant alloys such as Ni-Mo and Fe-Cr-Al based alloys, and these alloys with the DBC system were creep-deformed slowly under external applied stresses. A simultaneous diffusion coating process for Al and Hf was developed using Hf+NH4Cl+Al2O3 pack cementation. To obtain reliable and long-life coatings the combination of alloy substrate, coating, and external scale should be considered as a total system, to optimize oxidation resistance, structural stability, and mechanical properties.

Jan 1, 2010

By A. A. Rafiei, J. A. Finch

A previous study comparing n-pentanol and the polyglycol Fl50 showed that the two reagents could give the same gas holdup but with different size bubbles. The finding implies that bubble rise velocity depends on the surfactant (frother) type. A study using bubble swarms supported the frother type effect but bubble interactions were a possible confounding factor. This study resolves the question by measuring the rise velocity of single bubbles of 0.8-2.5mm diameter over a distance :::: 300cm in n-pentanol and F 150. It is shown that at typical frother concentrations used in flotation that the rise velocity in n-pentanol remains comparable to that in water alone while in Fl50 the velocity is significantly reduced. The results confirm the suspected impact of frother type. It is illustrated that in n-pentanol the rise velocity does not reached terminal; while in Fl50 it does and this is the source of the velocity difference. Advances

Jan 1, 2009

By X. -G. Chen, K. Liu, N. Parson

"Precipitation-strengthening 6xxx alloys are widely used for building and construction and automobile industries due to their high strength, good weldability and corrosion resistance. However, their elevated-temperature properties (250–300°C) decrease rapidly due to the fast-coarsening of precipitates. On the other hand, dispersoid-hardening is one of the most efficient approaches to improve the elevated-temperature properties. Therefore, the evolution of dispersoids during heat treatment in Al-Mg-Si-Mn alloys was investigated in the present work. Various heat treatments with temperatures ranging from 300–500°Cfor up to 24 hours were performed. Electrical conductivity and microhardness were measured while optical and scanning electron microscopy combined with image analysis, were used to characterize the dispersoids. Special emphasis was placed on the evolution of the size and number density of the dispersoids under different heat treatment parameters. It was found that dispersoids started to precipitate at 350°Cfor 1 hour. Nucleation and growth were the main mechanisms at temperatures up to 400°Cwhile coarsening occurred at temperatures above 450°C. The quantitative results indicated that dispersoids precipitation reached the optimum condition after treatment at 400°Cfor 2–4 hours with a fine size and high number density, resulting in the highest hardness.INTRODUCTIONThe precipitation-hardening 6xxx aluminum alloys with major alloying elements of Mg and Si are one of the most widely used aluminum alloys for building and construction and automobile industries (Dinaharan & Murugan, 2012). In recent years, there have been increasing demands for aluminum structural components to be used at elevated temperatures (250–300°C) for different applications. However, the mechanical properties of 6xxx alloys at elevated temperature are typically reduced due to the rapid coarsening of precipitates at 250–300°C. It has been reported that the yield strength (YS) of AA6061 in the peak-aged condition drops from 276 MPa at room temperature to only 30 MPa at 315°C(Kaufman, 1999). Therefore, it is a key concern to improve the elevated-temperature properties of 6xxx alloys to expand their range of applications."

Jan 1, 2018

By L. Tong

The nickel laterite ore is composed of soft and hard minerals, and nickel distributes preferentially into the soft mineral rather than in the hard. Selective comminution of saprolitic and goethitic nickel laterites is investigated to upgrade nickel into the fine fraction using stirred milling. The optimal selective grinding conditions were determined through a kinetic study and the limit of selective grinding and nickel upgrade was analyzed. The breakage rates of minerals, grinding time, and the weight ratio of soft and hard minerals in the feed play an important role in selective grinding. A small breakage rate on hard minerals and a large breakage rate difference between the minerals are optimum for selective grinding. The soft mineral grade decreases with grinding time and the optimum grinding time is a trade-off of the soft mineral upgrade and recovery. The minerals weight ratio determines the limit of selective grinding. The effect of nickel upgrade is determined by both the conditions that influence selective comminution and the nickel grades in both the soft and hard minerals. The nickel grade in the soft mineral determines the limit of nickel upgrade.

Jan 1, 2015

By J. Grignon, C. Fleming

It is possible to reproduce the performance of an operating CIP or CIL plant in the laboratory, in small scale batch kinetic tests, coupled with mathematical models that translate kinetic data into predicted steady state gold profiles across multi-stage adsorption circuits. Once the performance of the commercial plant has been mimicked by the model, the plant operating parameters can be varied systematically in the model, and the likely response of the plant to the step wise change can be determined. In this way it is possible to inexpensively optimize the operating conditions of an existing plant, with no disruption to plant operations and no economic risk to the mining company. This approach had been adopted by IAMGOLD to optimize the performance of their Rosebel CIL plant following several major expansions in mill capacity since 2004.

Jan 1, 2011

"An innovative concept is proposed whereby the operating power for haul trucks in certain areas of an underground mine are reduced in order to lower ventilation costs. Airflow that must be provided for diesel-powered equipment in most jurisdictions are regulated based on engine peak power capability and engine emissions, both of which can be lowered by artificially reducing the capacity of the engine through the engine control unit. Advances in asset tracking and ventilation on demand enable this methodology and this study demonstrates that it could represent significant value for mine operators. An examination of haul truck duty cycle indicates that de-rating of engine operating power based on the truck’s location in the mine can enable a step change in ventilation rates, often with no material impact on working conditions. Methods for implementation and estimate of cost savings will be defined.INTRODUCTION Ventilation of underground workings remains a significant operating cost burden for modern mine operators. In particular, ventilation rates for underground diesel mining equipment are often defined by local regulatory bodies and are assumed to present minimal opportunity for optimization or savings, at least until battery propulsion systems can be adopted. Commonly, the quantity of air flow required is defined by the peak rated engine output power of diesel equipment. For example, Ontario Regulation 854 SS 183.1 (3) states that “The flow of air must be at least 0.06 cubic metres per second for each kilowatt of power of the diesel-powered equipment operating in the workplace”. Jurisdictions that define air flow using the prescribed CANMET or MSHA ratings use peak engine emissions to calculate air flow required for dilution ventilation. These approaches are similar in that the maximum power capability of a vehicle’s engine is used to define the ventilation rate in all areas where it travels, regardless of what power output is actually used in any of those areas. Examination of the duty cycle of a typical underground haul truck identifies a large variance in the power output of the vehicle depending on its location in the mine and the activities undertaken at these locations. For example, travel on a mining sub-level requires a fraction of the truck’s peak power due to the minimal grade and significantly reduced travel speed. So if we can reliably reduce the peak engine power capacity and engine emissions in areas where peak power is not required, we can logically cut the ventilation rates for those areas."

Jan 1, 2017

By Bryan Tisch

Goal of GMGE ??To advance mine reclamation through the beneficial use of organic residuals for the sustainable establishment of bioenergy crops and other productive land uses Objectives ??To advance the current ?standard? of mine reclamation by demonstrating that mining lands can safely become agriculturally ?productive? through the use of organic residuals. ??To generate and compile sound scientific data that can be utilized by stakeholders to better assess the environmental impacts of utilizing these materials. ??To complete a manual of best practices regarding the utilization of organic residuals on mine lands. *Considerable effort to be placed on operations/implementation side of utilizing residuals ?rather than just pure research

May 1, 2011

By J. Visman

"Cyclone separators of different design are being used in increasing numbers in the coal industry of today. One recent addition, the Compound Water Cyclone, is finding application in the North American and Australian coal fields for the beneficiation of coking coals and for the reduction of sulphur and ash in steam coals. In this paper, the combination of specific-gravity separation, thickening, classification and water recovery are discussed. All of these operations can now be accomplished by means of cyclones that are effectively combined in circuits of compact design. In the layout of such integrated plants, three main sections are distinguished, namely: a Main Section for cleaning the plus-28-mesh fractions; an Effluent-Beneficiation Section for treating the minus-28-mesh fractions; and a Water-Recovery Section, where the wash water is reconditioned, and the fine solids are removed in a semi-solid state as slugs or pellets. Depending on the nature of the coal and the specifications of the purchaser, water-cyclone circuits can be flexibly combined with HM Cyclones and froth flotation, as well as with ancillary equipment for dewatering and drying."

Jan 1, 1968

By F. Habashi

Lead is an ancient metal, has been produced to-date from its ores exclusively by pyrometallurgical route. The process suffers from high operating cost and excessive pollution problems. Extensive research has been going on since the beginning of the twentieth century to find a non-polluting process for its production and a solution for its complex refining scheme. It has been assumed correctly that the hydrometallurgical route should be the most promising. Pilot plants have been constructed and operated for a reasonable periods, but no process has proved to be satisfactory. As a result, a number of smelters and refineries have been shut down. The present review analyses the situation and suggests that the best route to treat lead sulfide concentrates is by leaching with fluoroboric acid, HBF4, containing ferric fluoroborate, Fe(BF4)3, and electrolyzing the solution in a diaphragm cell - - a process recently invented by Italian metallurgists. In this process, any silver present in the concentrate remains in the residue together with elemental sulfur and can be recovered by known methods.

Jan 1, 2008

By Z. D. Hora

Sev_eral dozen si lica occurrences have been reported from various parts of Brit ish Columbia. Some represent hydrothermal veins or parts of pegmatite bodies; other are recrystall ized sandstones. Several vein type deposits were mined for smelter flux and as a source of white chips for stucco dash and simi lar products. Some quartzites were studied as potential sources of high-grade silica for ferrosilicon and silicon metal production. The province's only production of silica for ferrosilicon has come from a pegmatitic quartz plug near Oliver in southern British Columbia. Its reserves are now practically depleted.

Jan 1, 1984

Strips of AA6111 automotive alloy were cast on a horizontal single belt strip casting simulator, Pure copper and carbon steels substrates plasma sprayed with different coatings for improving the strip surface quality, were used as chill moulds, Experimental studies revealed that a graphite coating provided the greatest benefit in achieving good surface quality. The interfacial heat fluxes during solidification of AA6111 strip were calculated by the IHCP method (Inverse Heat Conduction Problem). Temperature variations and cooling rates within the strips were then calculated through numerical simulations based on the time-dependent heat fluxes obtained by IHCP, The effects of casting parameters, including casting temperature and strip thickness, on interfacial heat fluxes, cooling rates and microstructures, were investigated, Although the maximum interfacial heat fluxes on the chill copper substrate were much higher than the results obtained from the steel substrates, the solidification times of the melts were mainly determined by strip thickness. Very fine equi-axed grains were obtained for both 1.2mm and 2.5mm thick strips thanks to the rapid extraction of heat, and effective grain refinement.

Jan 1, 2005