Search Documents

By W. Schubert, N. Radoncic

"The term “squeezing” is frequently used, although it is ill defined. Definitions like “large and long lasting displacements” raise the questions about the threshold values for the magnitude and duration of displacements. Large displacements during tunnelling frequently are observed in fault zones with high overburden. Whether this causes problems very much depends on the design approach used. On the one hand, the magnitude of expected displacements has to be predicted prior to excavation to provide for enough allowance for the displacements without violating the clearance profile. On the other hand, the support characteristics must be compatible with the expected imposed strains. As the magnitude of the displacements and thus the strains in the support depend on the support capacity and its characteristic (yielding potential), only well engineered systems will be successful.Experience in Alpine tunnels over the last decades has shown that closed shotcrete linings can sustain a strain of approximately 0.8% to 1% without failure. Any strain above this value inevitably leads to failure of the lining, and thus a loss of resistance, causing additional displacements. Based on a large number of simulations, a criterion for a critical overburden depth up to which closed linings can be used has been developed. Traditionally open gaps in the shotcrete linings have been used to allow for larger strains. To enhance the efficiency of the linings, yielding elements have been developed, which are integrated in the shotcrete lining, allowing large strains and controlled development of support resistance (Figure 2). When designing such yielding support systems, the development of the displacements, as well as the rheological behaviour of the supports must be considered. As the development of displacements to a large extent depends on the face advance, also the advance rate has to be considered, to be able to compare the time-dependent strength of the lining to the stresses developing as a result of the imposed strains. Another issue is the compatibility of the rock bolts with the large strains. With standard grouted bolts, there is a potential that the “fresh” grout is sheared due to the initially large strain rates. Special rib designs of the bolts allow for a higher strain tolerance.For successful tunnelling through fault zones quality monitoring and up-to-date data evaluation is of crucial importance. With advanced evaluation tools, changes in the ground conditions ahead of the face can be reliably predicted. With the help of empirical relations, the development of the displacements for different advance rates and supports can be predicted, allowing for the determination of the required overexcavation.The paper presents a review of the development of ductile elements, methods of analysis, and monitoring data interpretation."

Jan 1, 2015

By G. McIsaac

This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone?s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place. Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. ?Whatif? scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan.

Sep 1, 2005

By C P. Gravenor

In 1953, a deposit of sedimentary oolitic iron ore was discovered in the Clear Hills area of northwestern Alberta. Since that time, detailed drilling has outlined reserves in excess of 200 million tons of ore grading 30 to 35 per cent iron. Attempts to physically beneficiate the ore to meet blast furnace or direct reduction feed specifications have been, in general, unsuccessful. In 1960, Premier Steel Mills Limited and the Research Council of Alberta jointly sponsored a pilot-plant test at the R-N Corporation at Birmingham, Alabama. About 5,000 tons of ore were treated, and briquettes containing 90 per cent Fe were produced, with 83 per cent recovery. At the same time that the R-N tests were being made, the Research Council initiated a program to produce high-purity powders by chemical methods. Several purification techniques were investigated; hydrochloric acid dissolution of reduced ore was finally adopted. Briefly, the steps involved in this acid process are as follow

Jan 1, 1964

By Seunghoon Lee

The increase in the number of higher and larger buildings is expected to require the buildings' outer wall maintenance process, which includes cleaning, painting and monitoring, still depends on manpower. In this study, we proposed the robotic building maintenance system and aimed to reduce the jerk effect through the motion control of the system, improve the performance of the maintenance task, and ensure longer life and safety by improving the stability of the building structure and robot system. Through the results of the motion control and field-test with the proposed system, in specific, horizontal sliding module (HSM) showed that the jerk oriented by impact force was significantly reduced, feasibility of the proposed method was verified, and the robotic challenges were explored.

Aug 1, 2013

By G. T. Lapidus, J. Trejo-Gallardo

A phenomenological model is presented for leaching silver from silver sulfide contained in mineral particles with ammoniacal thiosulfate solutions of copper in stirred reactors. Experimental results were used to adjust the kinetic parameters of the model, such as the reaction order and velocity. The incorporation of the cuprous sulfide-silver sulfide equilibrium at the reaction interface allowed the prediction of the conversion limits for different reagent concentrations. The information obtained from the reactor model was later integrated into a heap leaching simulation, whose results adequately describe tendencies observed in column tests, with respect to variations in copper and thiosulfate concentrations. Comp

Jan 1, 2005

By George Efremidis, Markos Avlonitis, Elias C. Aifantis, Avraam Konstantinidis

"Nowadays, there is an increasing interest for realistic spring-block models capable of addressing precursor phenomena in catastrophic earthquake-induced landslides. By pre-defining the constitutive law between externally applied stress and induced local strain increments, the dynamic behaviour of the rock/soil slope can be studied by means of the distribution of slip events at the interface between the soil and the bedrock. It is shown that by relaxing the assumption of constant of externally applied stress rate and local strain increments, a robust 2D spring-block model can be formulated for studying triggered landslides. A cellular automaton is built in order to examine the dynamic behaviour and the stability of rock/soil slopes during the initiation of a landslide. The type and nature of the failure plane, as well as the triggering mechanism is studied. The different dynamic evolution modes of the slope can be mapped to specific shape parameters of the corresponding distributions of the incremental displacements. The proposed spring-block model can be used in order to understand, predict and minimize the impact of catastrophic landslides triggered by earthquakes.INTRODUCTIONEarthquakes have long been introduced as one of the major cause of landslides. Earthquake induced landslides are of great importance because they can cause considerable damage and life casualties. Existing analyses can provide landslide concentration, i.e. the number of landslide sources per square kilometer of surface area, as well as the distance from the earthquake source, which is related to the strength of shaking, the slope steepness, which is connected to shear stress, and finally the rock type, which is referred to material strength (Keefer, 1984). In spite of their great importance in social and economic life, earthquake-induced landslides are still considered as an open geotechnical problem. The dependence of the number and distribution of landslides on earthquake magnitude and ground shaking intensities is a crucial factor for the description and determination of the phenomenon. The hazardous types of earthquake-induced landslides, the most susceptible geologic materials and the reactivation of landslides originally triggered by nonseismic activity are some important topics for areas affected by landslides. Most of these areas present an irregular and asymmetric shape with respect to epicenters and fault ruptures, and also show a strong correlation with magnitude (Keefer, 1984, 2000). The number of landslides caused by an earthquake generally increases with increasing earthquake magnitude. Keefer (1984) presented a magnitude scale in order to quantify the number of earthquake-induced landslides. Malamud et al. (2004) have proposed an independent landslide-event magnitude scale on the earthquakes, based on the logarithm of the total landslides number associated with an event. The aforementioned studies try to relate the landslide magnitude scale to the visible effects of the triggering mechanisms."

Jan 1, 2015

By Mahmoud Ahmed

Three-dimensional models are in increasing demand for design, maintenance, operations and construction project management. Point-clouds are the main output of automatic data collection using laser-scanners and photogrammetric technologies. Pipe-works may comprise 50% of the value of important construction projects such as industrial and research facilities. We have developed a practical and cost-effective approach, based on the Hough-transform and judicious use of domain constraints, to find, recognize and reconstruct/model 3D pipes within point-clouds fully automatically. The developed approach allows pipe growing within a 3D point-cloud. It samples the point-cloud to sequential orthogonal slices, detects pipe?s cross-sections within sampled slices and grows the pipe along the cross sections centerlines. It is validated using laser-scanner data from construction of the Engineering-VI building on the University of Waterloo (UW) campus. The system works on a typical laptop. Recognition and localization results are within a few millimeters. The presented approach opens the gate to broad applications of pipe-network modeling.

Aug 1, 2013

By Michael L. Wayman

Native copper is copper which exists in nature in elemental, metallic form, rather than being chemically combined as is the case with the more usual oxides, sulphides, carbonates, etc. Several other metals, including gold, silver and platinum also occur in native form as do, rarely, iron, lead and mercury; a few naturally occurring native metal alloys, notably electrum (gold-silver) and tumbaga {gold-copper or gold-silver-copper) are also known. An analysis of the relative availabilities of native metals as nuggets in a useful size range111 shows native copper to be by far the most abundant of the native metals, exceeding both gold and silver by at least two orders of magnitude. While such an estimate is crude, it serves to illustrate why copper was one of the first metals to have been used by ancient peoples. Native copper is known to occur on all inhabited continents, although its exact occurrence and abundance in ancient times cannot be unambiguously determined because many surface deposits may have been totally exploited and are therefore no longer identifiable. It is clear, however, that native copper does or did occur in all areas inhabited by the early metal-using cultures, for example in the Andes, in Central America and in the Near East. It is remarkable that most of the world's native copper occurs in the deposits of the Lake Superior region, primarily on the Keweenaw Peninsula of northern Michigan and on Isle Royale, an island in Lake Superior some 50 miles north of the Keweenaw deposits. Canadian deposits of native copper are found in Newfoundland and Labrador, Nova Scotia, Quebec, Ontario, British Columbia, the Yukon and the Northwest Territories (on Victoria Island, Bathurst Inlet and the Coppermine River area). It was to locate the latter deposits that the explorer Samuel Hearne was sent overland from Hudson's Bay in 1770; they were also surveyed by Sir John Franklin's expeditions in the 1820s.

Jan 1, 1999

By J. Walker, G. E. Kim

Since May of 2000, Mogas Industries, in partnership with F.W. Gartner Thermal Spraying Co. and using the services of Perpetual Technologies, has invested time, energy, and resources towards developing novel ball valves for high-pressure acid-leach (HPAL) service. In addition to developing new valve designs, an aggressive coatings development effort has been undertaken to improve the protective quality of the coatings so as to enhance the performance and extend the life of valves in severe HPAL conditions. In 2001, Mogas Industries qualified and applied a nanostructured titanium oxide (n-TiO2) coating for gold and nickel/cobalt HPAL services. The n-TiO2 coating provided dramatically superior protection against abrasive and erosive wear, fared very well against high-pressure autoclave corrosion testing, and has performed well in HPAL service.

Jan 1, 2004

By F. A. McLean

At the Annual Western Meeting held at Blairmore, Alta., October 1924, the writer presented a paper drawing attention -to the advantages of portable gas-driven equipment for developing isolated mining properties. This type of equipment was at that time practically in its infancy and the details of results actually accomplished were somewhat meagre. During the last year or so a number of these plants have been installed so that it is now possible to offer more definite information regarding the actual mining progress accomplished with such plants and their cost of operation in various parts of the country. This paper has been written with the idea of reviewing the work done during the past year, and to supply data which may be of interest to those wh9 are confronted with the problem of selecting equipment for development or assessment work. Because drilling operations play such an important part in mining, one of the first problems that usually confront the prospective? mine owner is the selection of the proper com-pressed-air plant. The size and type of equipment and the method of driving it require careful consideration. The size and type of equipment is determined largely by the funds available, transportation facilities, and the speed with which the programme of development is to be carried out. The selection of the proper method of drive usually depends on local conditions, such as the relative cost of various fuels, and has an important bearing on operating costs.

Jan 1, 1926

By K. Bunney, R. Pleysier

The deportment of a suite of elements through representative gold ore processing unit operations in cyanidation has been investigated. Chromium and lead are not soluble in alkaline cyanide solutions. Arsenic, antimony, cobalt, molybdenum, selenium, tellurium and vanadium are soluble, but typically do not adsorb onto activated carbon to any appreciable extent. Silver, copper, cadmium, mercury, nickel and zinc to varying extents report along with the gold to the carbon eluate. Cadmium, mercury and zinc can report to the carbon regeneration kiln off-gases. Strontium is soluble and adsorbs on carbon where it remgins.

Jan 1, 2011

By D. J. Lucifora

Monitoring-While-Drilling (MWD) is a proven technique that records instantaneous on-drill parameters which can be used to supply contextual information for in-situ, down hole conditions, such as: changes in geology, the presence of pre-existing fractures and dynamic alterations, down hole conditions including bit bailing, bit blockages and bit wear, and improper drill operation. This technique has been widely used in the oil and gas industry and, eventually, it was transferred to the mining industry. A challenge when analyzing and interpreting MWD data is in utilizing proper filtering which enables one to properly eliminate any ?noise? from the signals of interest. Overall the importance of MWD data is that, through the collection of operational field-based data, a dataset can be acquired which allows experimentation and analysis to be carried out. Such a dataset is often impossible to replicate in a laboratory setting. If successful, and through iterative refinement, any promising method can eventually be implemented on-machine and using real-time monitoring techniques. This paper will provide a state of the art review of presently used MWD techniques and applications in industry. The paper?s primary focus will be on shallow, mining-style, blast hole drilling but will also take into account techniques and applications utilized in oil and gas drilling which have not been adopted in the mining industry. In the cases where MWD techniques and applications exist solely in oil and gas drilling the paper will examine and comment on the potential utility of technology transfer to mining applications.

Aug 1, 2013

By R. J. McCarthy

In-pit Crushing and Conveying (IPCC) is increasingly being considered by mining companies as a means to reduce their dependence on trucks and thus, fuel, tires, labour, etc. There is potential for great savings in operating costs which ultimately can mean better economics for a mining project. Vale has considered the application of IPCC at its Moatize coal project in Mozambique. Up to three studies have been conducted with the latest, at a pre-feasibility level, showing some promise. This paper explores the mine planning and IPCC engineering elements required in an IPCC study, their application to the Moatize project, and the drivers which most impact the viability of IPCC at Moatize.

Aug 1, 2013

By Walker. P. W. A.

Abstract -The Riviera tungsten occurrence in the Cape Province of South Africa was discovered in October 1979 as a result of stream-sediment panned concentrate sampling. The Cape age granite and late Precambrian Malmesbury Group carbonates and chlorite schists which it intrudes and which host the mineralization are covered by between 10 m and 30 m of Tertiary/Recent alluvium and clay. The scheelite/powellite and molybdenite mineralization occurs in a greisenized granite cupola with an overprint of porphyry-type alteration as well as in minor skarns. The ore reserve is estimated to be 46 million tonnes at an average grade of 0.2160Jo W03 and 0.020% Mo. The deposit is uneconomic at current tungsten prices.

Jan 1, 1994

By W. Basuki, B. Setyotomo, L. Hakim, R. Hendrajaya

Due to high crack sensitivity of slab product of gas and oil line pipe application, its steel making process and alloy composition were evaluated and then improved to overcome its critical solidification process and reduced surface defects. The study was conducted at Slab Steel Plant Krakatau Steel. The purpose was to improve slab surface quality by reducing surface defects so that the slab surface doesn't need to be totally repaired. The method applied was by performing plant trial process, which the secondary process parameters such as alloying method and the casting parameters such as casting powder selection, metallurgical cooling, mould level control, and superheat were continuously monitored and then adjusted to the surface quality of the product. Based on the calculation of Ferrite potential of the steel, the chemical composition was designed to achieve optimum casting parameters in order to avoid high shrinkage during solidification. The results of the study are decreased surface defect quantity, and smooth casting process. The quantity of crack decreased by almost 90%. The slab surface repairing was significantly reduced from 85. % to less than 10%. These new casting parameters and developed alloy composition are then used and standardized for the mass production of the steel.

Jan 1, 2005

By E. L. Bruce

EUROPEAN Russia is mainly a great plain, the average elevation of which is only 600 feet above sea level and the maximum elevation less than 1,200 feet (Figure 1). The main divide between the Arctic ocean and the Black sea and Caspian sea is an indistinguishable topographic feature from which the Dneiper and Don rivers flow southward to the Black sea and the Volga river to the Caspian. The valleys of these rivers are but little below the general level (Figure 2). To the south, this great, rolling plain is broken by a low ridge of Precambrian gneisses and intrusive rocks. The Crimea is an upland from which the descent to the Black Sea coast is precipitous (Figure 3). The Ukrainian Soviet Socialist Republic occupies the southern part of the plain. It is the southwestern unit of the Union, bordered by Rumania and Poland on the west and by the Crimean Soviet Socialist Republic on the south.

Jan 1, 1938

By Rejean Gagnon, Fernand Rochefort

"Haulage costs, in most operations, represent a large portion of total cost. Quebec Cartier Mining Company came to the conclusion t hat an electric trolley assist providing more horsepower than available from dieselgenerator sets presented the best oppor tunity for improvement. Accordingly, a testing and development program was carried out which resulted in the design, installat ion and application of a practical system. This paper describes the development of the system, the equipment used as well as the actual operation. A projection is also made to indicate further improvement in productivity. A comparison is made of truck operating data before and after activation of the trolley assist system in order to determine its economic impact."

Jan 1, 1972

By G H. Reavely, The University of Western Ontario Department of Geology

The lower Middle Devonian Sylvania Sandstone occurs in the sub-surface in the western part of Mal-den township, Essex county, Ontario. The formation is composed of well rounded, frosted quartz grains with a silica content varying from 42 to 93 per cent and the grains are cemented by carbonate, constituting up to 57 per cent of the rock. This sand-stone is not a homogeneous bed but is divided by strata rich in carbon-ate cement. The thickness of the Sylvania in Malden township varies up to a known maximum thickness of 88 feet. The lower contact with the chert-bearing Bois Blanc formation is sharp but the upper contact with the Amherstburg formation (Detroit River group) exists as a transition by a gradual downward increase in quartz grains. The Sylvania would seem to outcrop in the lake bottom near the mouth of the Detroit River dipping to the north along a broad anticline the axis of which follows the Detroit River. Just south of Amherstburg, a local east-west trending

Jan 1, 1961

By J. Arzúa, L. R. Alejano, P. Rodríguez

"After six years of successful excavation with a support pattern, some roof failures have happened in a room-and-pillar underground mine excavated in a stratified rock mass. In this paper the authors give explanation to the failure mechanisms and redesign the support in order to solve the recent problems of roof collapse.The mine magnesite bed is approximately 14 m thick, and runs in the E-W direction with an average dip of 18º. Due to mine constraints and the inexpensiveness of the ore, the excavation is performed in the mineral itself, avoiding the need for mining dumps and waste excavation. Rooms and drifts are oriented in the mineral bed to form an angle of 19º to the direction of the strata, reducing the roadway gradients to less than 10%. Rooms are 11 m wide and pillars are 7 m wide. They are designed to leave a 1 meter thick magnesite bed in the roof of the rooms to act as a supporting beam. More often than not there is a layer of very poor quality marly shale up to 1 m thick resting on this magnesite beam. Overlying the poor quality marly shale there is a better quality, self-supporting sandy shale.First, a characterization of the involved rock masses (magnesite, marly shale and sandy shale) is performed, collecting the geotechnical data from previous studies and performing new in situ geotechnical surveys to check the soundness of the previous data. A distinction is made between different quality zones inside the mine by means of the RMR classification, associated to the occurrence of faults.Back-analysis of some of the failed rooms and data from exploration boreholes were used to determine the failure mechanisms (associated to Voussoir type failure or occurrence of sub-horizontal joints crossing the magnesite beam). Based on an understanding of these mechanisms, the method used to design the support and to analyse the stability of the different possible thicknesses of the magnesite beams of the rooms and drifts of the mine were improved.Numerical models of the most relevant conditions found in the mine were performed in order to better understand the behaviour of the roofs and to simulate the supporting solution obtained in the previous analyses.The most relevant conclusions with regard to the main elements causing the instability of the roof include the appearance of sub-horizontal discontinuities crossing the magnesite bed, which causes total instability of the roof and usually leads to collapse; excessive thinness of the magnesite beam in the problematic rooms; and the relaxation of the deepest (around 270 m in depth) zone of the mine because of existing faults."

Jan 1, 2015

By S. M. Fatemi-Varzaneh

The AZ31 magnesium alloy is considered as a promising alloy in various applications and industries. Furthermore, to design a proper hot working process (rolling, forging and extrusion), the assessment of hot working behaviour of the alloy is necessitated. Accordingly, the hot deformation behaviour of AZ31 alloy was studied through hot compression testing method. The latter was carried out in a wide range of temperature (523 K to 783 K) and strain rates. The obtained true stress-true strain curves and final microstructures were examined and a partial melting was realized at 740 K. It was concluded that the presence of liquid did change the deformation mechanisms thereby affecting the flow behaviour.

Jan 1, 2005