Search Documents

By J. Currie, J. McManus, R. Chenier

"Cominco Copper Division's Valley Mine is located in the Highland Valley of British Columbia, approximately 275 km by air northeast of Vancouver. The nearest towns are Logan Lake, located IS km to the east and Ashcroft, located about 50 km to the northwest.Preproduction stripping of rock and overburden at the Valley Mine's Lake Zone Pit began in mid-1982 following a decision to discontinue mining in the adjacent Jersey Pit. Equipment and mining methods were carried over from the Bethlehem Copper operations which, with Valley Copper Mines, were merged into Cominco in December 1982.Blasting practices, as carried over from the Bethlehem pits, were designed to provide the fine fragmentation required to meet production requirements using the Bethlehem crusher. However, after mining the first few benches of the Lake Zone Pit, it became apparent that overblasting at the pit limits was causing a number of bench failures, as well as contributing to an over-all reduction of the material strength of the rock mass forming the southwest wall of the pit.With present ultimate pit plans calling for the southwest wall to be as high as 300 m, Valley staff realized that potential slope stability problems should be dealt with as early as possible. This philosophy would enable experimentation on phase pit walls in order to attain the optimum slope angle on the ultimate pit wall.As part of an over-a ll slope stability program, a controlled blasting program was initiated at the Lake Zone Pit in March 1983. In this program, Valley engineering and production staff worked together with Golder Associates in establishing design criteria and evaluating the results. This program resulted in a marked improvement in the soundness of pit walls while maintaining the required degree of fragmentation."

Jan 1, 1985

By P. K. Gummer

Gold was fir t di covered on the Seabee property in 1947 by the Con olidated Mining and Smelting Company Limited. Acquired by Claude Resource Inc. in 1984, the property is now being explored by Placer Development Ltd . in joint venture with Claude Re ources. Between Augu t, 1985 and March, 1986, Placer completed 54 drill holes, extending the main o. 2 and o. 5 vein y tern to a depth of 1000 feet below surface and di covering two new satellitic gold zone 800 feet west of the o. 5 gold zone. Drill proven and probable geological re erve in four zone ( os. 2, 5, II, 14) to a vertical depth of 1000 feet, are approximately 1,120.000 tons averaging 0.32 oz. Au/ton.

Jan 1, 1986

By C. H. Ash

"The Red Chris Cu-Au deposit (522.7 Mt at 0.35% Cu and 0.27 g/t Au), northwestern British Columbia, is one of several pre-accretionary porphyry systems in the Cordillera of westernCanada. It is hosted by an Early Jurassic hornblende monzonite to quartz monzodiorite porphyry which forms part of a suite of dikes and stocks that intrude Late Triassic volcanic strata. Major and trace element chemical data suggest that these Early Jurassic intrusions have compositions which fall on the boundary between alkalic and calc-alkalic compositions. Alteration and mineralization in the Red Chris deposit are more typical of calc-alkaline porphyry systems with abundant potassic, sericitic and argillic assemblages and quartz-rich stockworks. It lacks Na- and Ca-bearing silicate assemblages which characterize the alkalic porphyry deposits of British Columbia. One of the more unusual features of the deposit is the abundance of carbonate alteration and veins which occur throughout the hydrothermal history of the deposit. This type of alteration and veining is more typical of alkalic porphyry deposits.The composition of the carbonates vary both temporally and spatially with different alteration zones. Potassic zones, which are characterized by orthoclase±albite±quartz±chalcopyrite±bor-nite±magnetite±hematite and Au/Cu ratios of 1:1 (g/t Au:% Cu), contain minor siderite veins and alteration. Quartz-sericite-carbonate (QSC) zones overprint earlier potassic alteration and comprisequartz+ankerite+sericite+pyrite+chalcopyrite with Au/Cu ratios of 0.5:1 (g/t Au:% Cu). Ankerite isthe main carbonate in this stage but has a variable composition with a more Fe-rich variety associated with mineralized veins. Localized chlorite-carbonate alteration zones, characterized by chlorite+carbonate+quartz±kaolinite±pyrite±gypsum and high Au/Cu ratios [2 to 3.5:1; (g/t Au:% Cu)],contain predominantly calcite. Late stage carbonate-gypsum veins have an ankerite to dolomite com-position which is very similar to the regional carbonate alteration and veins."

Jan 1, 1997

By K. Esmaieli

The Synthetic Rock Mass (SRM) approach has the potential to capture the mechanical behavior of large rock samples. In order for the method to be used with confidence it is necessary to gain a good understanding of the factors that influences its analysis. This paper reports on a series of numerical experiments, based on field data from a large underground mine, to investigate the influence of intact rock mass strength of a constructed (SRM). A jointed rock mass defined by three fracture sets was simulated by a Discrete Fracture Network (DFN) model. The generated fracture network was subsequently embedded into six different intact rock samples, simulated by a bonded particle model in PFC3D, generating six SRM samples. Each intact rock sample was 7 m × 7 m × 14 m and assigned different mechanical properties. The first intact rock sample was assigned a uniaxial compressive strength of 205 MPa and an elastic modulus of 104 GPa with the UCS and elastic modulus values of the other samples downgraded by 10% until the weakest sample had a UCS value of 121 MPa and an elastic modulus value of 61 GPa. All SRM samples were loaded under uniaxial compression to obtain the complete stress strain curve. It was observed that the compressive strength of the rock mass samples decreased by 10% following the same trend as the rock material strength. However, the elastic modulus of the rock mass samples decreased non-linearly with reduction of the elastic modulus of the rock material. The Poisson's ratio of rock mass samples does not change with decrease of rock material properties. For the post-peak behaviour the results show that both the brittleness index and the residual strength of rock mass samples decreased as the rock material properties degrades.

Aug 1, 2013

By A. Taylor, E. Thorn Corthay, R. Storey

In response to requests from its stakeholders, the International Standards Organisation is engaged in development of an international standard for Energy Management Systems (EnMS) which will become "ISO 50001". This new standard will build on the successes of both the EN16001 EnMS standard that has been used by dozens of European companies, as well as the ANSI/MSE 2000:2008 EnMS standard that is currently being used in several pilot projects in the USA and Ontario. This paper provides an overview of the key points of the EnMS standards, and describes how they can be used to drive sustainable energy reductions in the metallurgy industry.

Jan 1, 2010

By Jack G. Hazan

The Critical Path Method is the modern scientific answer for solving the planning and scheduling problems inherent in today's complex projects. With this method, nothing is left to chance. All resources are controlled and kept to the minimum. The various phases are properly planned and strategically determined. Optimum conditions are evaluated for the most economical and fastest way to complete a definite project. The method must be fully understood and implemented with positive data and continuous feedback to obtain the best results. This paper covers the various aspects of the Critical Path Method and mentions some of its applications in the mining and metallurgical fields. T 0 progress to a higher state of human welfare necessarily involves sacrifices. The greatest sacrifice is to relinquish social freedom in favour of economic freedom. In the old days, for example, a cobbler was free to work at whatever time of the day he chose; today, he can't. He is now forced to adapt himself to environment and to work at stand-

Jan 1, 1965

By M. J. Nicol, T. Moyo

Ammoniacal solutions are an effective lixiviant for the oxidative dissolution of some mineral sulphides. A detailed study of the anodic dissolution of chalcopyrite in ammonium sulphate-ammonium hydroxide solutions has been carried out using cyclic voltammetry, chrono-amperometry and rest potential measurements. The role of the copper(II)/copper(I) redox couple in the oxidation process has been evaluated. Rest potentials have been found not to be affected by oxygen but to increase with an increase in initial copper(II) concentration. Pseudo-steady-state anodic current densities measured in the absence of copper(II) ions at the rest potentials obtained in the presence of copper(II) ions increase with increasing concentration of copper(II) ions, confirming the positive effect of copper(II) ions on the rate of dissolution of the mineral. Cyclic voltametric and chrono-amperometric data show that in the absence of initial copper(II) ions, the rate of dissolution in the presence of dissolved oxygen is significantly lower. These results confirm that the effective oxidant for the mineral under the conditions of the study is copper(II) and not dissolved oxygen. Coulometric measurements have been used to establish the stoichiometry of the anodic reaction at different potentials.

Jan 1, 2014

By N. Bartie

Realising the circular economy (CE) is faced with some significant challenges. Process metallurgy and its infrastructure play key roles at the heart of making the CE work. Therefore, the enabling role of process metallurgy within the CE will be central to the discussion in this paper, touching among others on product and system design as well as the key metallurgical and other process fundamentals that need to be investigated and understood to make the CE a reality. The central role of materials and its processing will be discussed in an integrated circular cities perspective. A key focus will be a discussion on designing a resilient “Smart Materials Grid” using and innovating metallurgical process engineering tools, which will manage the flows through Sustainable Circular Cities. The discussion will be using copper as leitmotiv of the discussion i.e. from copper ore, to metal, to complex products, recycling, product design and simulation and its impact. INTRODUCTION The transformation of our economies from linear to circular models in which waste materials become resources is the focus of the Circular Economy (CE) paradigm. Its important intentions: to take control of the damage we have been doing to the planet to ensure its livability and the welfare of future generations. This can only be achieved through careful utilisation of human, natural and economic resources. The concept is derived from several others (Beaulieu et al., 2015), of which Cradle-to-Cradle, Extended Producer Responsibility (EPR), Industrial Ecology, and Life Cycle Thinking are just a few. Other relevant concepts include resource efficiency (RE), design-for-recycling (DfR), and various others discussed by Blomsma and Brennan (2017) and Homrich et al. (2018), as well as various R-hierarchies e.g. Reduce, Reuse, Recycle (3R). However, does society comprehend these concepts, the actors and actions that influence them and how they interact? Do we know the limits of CE? Does society understand the key role of Copper and other metals to rendering the CE operable? True life cycle and systems thinking, focussed on simulation-based, process and metallurgical design are required to answer these questions. Lieder and Rashid (2016) identify nine widely-varying fields that study the concept ranging from sustainability sciences and engineering to economics, business, law, and social sciences. Overlap between questions addressed highlights the need for interdisciplinary collaboration (Nanz et al., 2017) in the assessment of the current status, and further steps needed to transform to CE. This doesn’t apply just in academia, but also in industry where concrete implementation of CE needs to occur at multiple levels, thus necessitating cooperation between government, civil society and other stakeholders (Beaulieu et al., 2015).

Jan 1, 2019

By L. S. Beck

"The Athabasca region forms part of the Churchill province of the Canadian Shield and is underlain by an Archean or Aphebian assemblage of rocks that underwent severe metamorphism and granitization during the Hudsonian orogeny (1750-1950 m.y. ago). In places, the eroded orogen is overlain by unmetamorphosed cover rocks (in-cluding the Martin and Athabasca formations) of probable Paleohelikian age. Basic dykes cut all the rocks of the region.There are innumerable vein-type pitchblende deposits and many syngenetic occurrences of uraninite in crystalline basement rocks. Evidence is presented to show that pitch-blende was emplaced during the final stages of the Hud-sonian granitization and followed the crystallization of syngenetic uraninite transitionally. In terms of P-T condi-tions, the pitchblende deposits belong essentially to Lindgren's mesothermal group.Based on the postulated uranium metallogenesis, the possibilities of finding further deposits of pitchblende and other types of uranium deposits are discussed."

Jan 1, 1970

By C. J. Mwenifumbo

Preservation of groundwater quality is a major environmental concern. The disposal of hazardous material from urban waste dumps, milling wastes in tailings ponds, and industrial wastes in injection wells may contaminate potential sources of potable groundwater. The containment or migration of contaminants in the subsurface depends on bedrock characteristics and type of overlying sediments. Fractured bedrock and permeable sediments that may provide pathways for the transport of potentially harmful contaminants should be avoided when selecting a disposal site. The role of borehole geophysics in hazardous waste-site investigations is reviewed in three categories: (I) site selection; (2) determination of the extent of contamination at existing sites; and (3) long-term monitoring of migration of contaminants. In the first category, borehole geophysical techniques developed for lithology and fracture identification, and for porosity determination, provide some of the necessary information for understanding the subsurface hydrogeology. Lithological information can be obtained from gamma-ray, electrical resistivity, induction, magnetic susceptibility, and sometimes induced polarization logs; fracture detection and characterization can be accomplished with the use of caliper, density, resistivity, temperature, and acoustic televiewer logs. Estimates of porosity are derived primarily from neutron-neutron, resistivity, density, and soniclogs. Borehole geophysical techniques used in water quality determinations include self-potential, fluid resistivity, Eh (redox potentials) and pH measurements, and these can be used to map the extent of contamination at an existing waste site. Cross borehole and borehole-to-surface electrical methods can also be used in this application. Long-term monitoring of contaminant migration in boreholes can be accomplished with techniques that respond to changes in electrical conductivity, temperature and fluid chemistry caused by the presence of contaminants.

Jan 1, 1993

By J. A. Vonhof, R. O. van Everdingen

Since 1949, a total of 59 disposal wells have been installed in Canada to inject liquid wastes from refineries, mining operations and chemical plants into subsurface formations at an ever-increasing rate. Well depths range from around 600 feet to almost 5,500 feet; injection rates range from 0.5 (U.S.) gpm to more than 1,000 gpm for individual wells; wellhead injection pressures range from a slight vacuum to over 500 psi. Apart from strictly technical considerations of well design, the geological, hydrodynamic and hydrochemical conditions at the disposal site have a strong bearing on the safety and success of such operations. Prevailing hydrogeological conditions in large portions of the country do not allow safe subsurface disposal.

Jan 1, 1973

By Ellis Thomson

The microscope is now used extensively not only in the examination of solid ore but also in the determination of fragmental mill products. It has therefore become a matter of paramount importance to be able to mount and polish fragmental as well as solid specimens in the easiest and most efficient way, so that the minerals present may be readily determined. In the case of the solid ore the ordinary mount of plasticine set on a glass or metal slide serves for most practical purposes. An improvement on this is furnished by the small brass container inside of which the specimen is mounted in a cementing medium of sealing wax. The latter is the method in use at Harvard University. It has the advantage of uniform height, thus obviating the necessity of a slide of any sort. It is also easily catalogued as the brass holder may be stamped with a convenient series of letters and numbers that will serve as a label. Other advantages of this type are the ease with which any particular part of the section may be re-located, the excellent storing facilities afforded by mounts of uniform size, and the possibility of polishing ten or a dozen sections at the same time by means of a holder which is placed over the polishing wheel, is geared with it, but revolves the opposite way.

Jan 1, 1926

By C. O. Swanson

"OUR INTEREST in estimates of world reserves of lead and zinc is focussed mainly on the information they give about the sufficiency of metal supplies for the future. However, we soon realize that the estimates can be interpreted in several different ways. Accordingly, it is necessary to have some under-standing of the elements represented by a compilation of world re-serves, and we will start by examining the accuracy of the estimates and what they attempt to measure.Variations in Estimates of the ReservesIf we study the estimates of world reserves that have been published in recent years, we note immenediately that they vary over a considerable range. For example, an article by Shea in 1947 gave world reserves as about 36 million tons of lead and 60 million tons of zinc. Shea did not in elude the United States but I have added to his totals the estimates made by the Bureau of Mines for that country in arriving at the foregoing figures. For approximately the same date, the American Zinc Institute and the Lead Industries Association reported world reserves as about 50 million tons of lead and 77 million tons of zinc. A comparison of the two sets of figures shows a mean variation of 30 per cent. For individual countries the difference between estimates can be even larger. A few years ago the estimate of Canada's reserves made by the United States Bureau of Mines was 7.4 million tons of lead and 14.0 million tons of zinc, while the Gordon Commission reported 1 O. 7 million tons of lead and 26.0 mil-lion tons of zinc. In this case the mean variation was 55 per cent."

Jan 1, 1960

By A. Boeing

Rock-breaker automation and remote operation improves the safety and efficiency of mining operations. This article presents an overview of the Rocklogic rock-breaker automation system architecture that provides collision avoidance, automated parking, and remote operation functionality. The system consists of a distributed computer control system that interfaces with sensors attached to the rock-breaker, the rock-breaker hydraulics, and the site infrastructure. We present results of an automated Transmin rockbreaker installed in a production environment at an underground Australian mine site. The system has been in production use for over 900 days during which there have been no reported collisions, and 100% adoption of the remote operation technology. As a result, Rocklogic has significantly improved the safety of rock-breaking operations and reduced the rock-breaking cycle time, thereby improving the sites overall throughput.

Aug 1, 2013

By Karl J. C. Harries

"The Table of Contents that follows is only an example and is the Table of Contents from an actual negotiated agreement. It is merely intended to show how an agreement might be set out and the nature of possible provisions. As a negotiated agreement the format was dictated by the negotiations. It is not offered as a precedent of what should be contained in a joint venture agreement (“JVA”), the “proper” sequence of Articles, or a complete listing of the contents of joint venture agreements generally. The set-up used for an agreement should be decided by the parties and be one they consider flows in a logical and workable sequence. This example sets out the “deal” first, followed by the provisions relating to how work is to be carried out and then by administrative provisions necessary to make the agreement work. If you are more comfortable with, say, having the Committee provisions at the beginning, by all means have it drafted that way -- you are going to have to live with the agreement and work under it.Notes:1. The Table of Contents provisions appear in bold print. The italicized sections are annotations, which have been provided in some cases where the heading may not clearly describe the contents. They are not intended to be comprehensive, but refer to some specific matters that are considered to be of interest or to need some clarification.2. The subject matter of many of the articles and paragraphs is discussed or commented upon in the text of the book. Some of section cross-references have been provided. Such references are only to sections where the topic is a principal subject and no attempt has been made to provide a comprehensive indexing.3. Although this particular agreement is a three-party agreement, *B* and *C*, the Owners, are required to act as a unit (see para. 1.09. – § 8.44.), making the agreement effectively a two-party agreement. The parties insisted upon having a decision-making Committee and structuring the agreement accordingly. As is explained in § 8.11., such an arrangement is not recommended and can result in problems.5. See also §§ 8.24., 8.41. and 14.13. for discussions on tables of contents, summaries, and headings."

Jan 1, 2003

By Ramsey Hart

MiningWatch Canada is the only national independent civil society organization with an exclusive focus on mining in Canada and Canadian mining companies operations internationally. In 2005, MiningWatch Canada collaborated with other NGOs to develop the Framework for Responsible Mining: A Guide to Evolving Standards. The project was the result of a perceived need by NGOs and retailers, particularly from the jewellery sector, for a framework that would set out environmental, social, and governance standards for the minerals sector ?providing recommendations for retailers and others seeking to source or invest responsibly, as well as regulate and encourage responsible mining practices?. This paper is a reflection on the Framework that examines key areas of concern and notes where the industry norms and expectations of civil society have evolved. The paper focuses on developments in social issues related to the UN Guiding Principles on Business and Human Rights, new initiatives associated with financial transparency, the UN Declaration on the Rights of Indigenous Peoples. The environmental components of the Framework that are revisited are waste management, biodiversity, energy and climate change, environmental assessment, mine closure, mercury and seabed mining.

Aug 1, 2013

By Xiaoguang Zhao

The coal mining area in Northern Shaanxi, China, has been taken as the study area, and the damage mechanism of the ecological environment is discussed on the basis of analyzing the characteristics of natural eco-environment and resource development in this area. Mining subsidence is taken as an example, and by using the Gray Correlation Analysis method, the key impact factors have been selected. An assessment model with fuzzy comprehensive evaluation has been constructed, and 12 coal mines have been quantitatively assessed. This paper also constructs an ecosystem health assessment method and index system in the coal mine area on the basis of ecosystem health theory, and assesses the ecosystem health status in the Shenfu coal mining area from 2000?2006. The research results are expected to help the eco-environment protection process in the designated coal mining area.

Aug 1, 2013

Barrick Gold Corporation is the gold industry leader, with 25 operating mines and a pipeline of large, long-life projects located across five continents, in addition to large land positions on some of the most prolific mineral districts. Barrick's high level of commitment to sustainable economic development and environmental stewardship was recognized by Dow Jones Sustainability Index (DJSI) - World, for the third consecutive year in 2010. The potential for adverse environmental effects from acid rock drainage (ARD) and metals leaching (ML) and their financial implications for Barrick are key considerations in our environmental assessment and business development processes. Barrick's membership in the International Network for Acid Prevention (INAP) reflects the importance of these issues to our business. INAP's development of the Global Acid Rock Drainage (GARD) Guide (a best practices guide for acid rock drainage prevention) provides Barrick with an important tool to assist in the assessment of environmental and financial risks from ARD and ML associated with our planned and ongoing mining operations (INAP, 2009). In this paper we will discuss how Barrick incorporates the GARDGuide and its principles for ARD and ML prediction and prevention in our business development processes and the management of our operations. The GARDGuide serves as a key reference for our project environmental assessments and as a common link between our projects and operations management, consulting specialists, permitting and regulatory authorities and the public. We will discuss how the GARDGuide is being "syndicated" throughout Barrick as a standard of practice and present a case study of how it was used in a recent Barrick Business Development Project.

Jan 1, 2011

By J. C. White

"During the early development of the Mattabi Mine in 1970, discussions with the Ontario Government revealed their policy of prohibiting, as much as possible, the development of new, isolated, single-industry townsites. Subsequently, Mattabi located its first housing in the Township of Ignace, which is situated 50 miles from the site of the mine and plant. Over 200 employees now commute 100 miles daily to and from work.This paper describes the experience gained and discusses the advantages and disadvantages of a remote townsite."

Jan 1, 1976

By Doug Milne

Linking Classification Systems with each other Similar Parameters between systems Different Rock Mass Properties Rock Mass Classification parameters and geology Different sources of data Commonly Used Rock Mass Classification Systems Q? = Q with SRF = 1.0 RMR? = RMR with no joint orientation correction RMR76 = 9lnQ + 44 RMR?76 = 9lnQ? + 44 RMR76 = RMR89-5 RMR?76 = GSI = RMR89-5 MRMR = ??MRMR

May 1, 2013