Search Documents

By D. A. Cormode

"INTRODUCTIONPine Point Mines, operated by Cominco Ltd., is located approximately 55 miles east of Hay River, N.W.T. by the southern shore of Great Slave Lake.The milling operation commenced in the fall of 1965 at a design capacity of 5,000 tpd. An addition which came on stream late in 1968 raised the nominal capacity to 8,000 tpd. Currently the milling rate is 11,000 tpd.The lead and zinc sulphides occur in dolomite host rock. Typical feed grades at present are 2% lead, 5.5% zinc and 5 % iron. When dolomite is present even in relatively minor amounts in the zinc concentrate, it presents serious treatment problems and causes inefficient operation of electrolytic zinc refineries.By 1972, it had become apparent that magnesium rejection in the form of dolomite was deteriorating because of increased plant throughput of less amenable ore. This paper will briefly outline the Pine Point zinc flotation circuit and will discuss the two phase program for reducing the magnesium level in the zinc concentrate. The program included changes and alterations to the flotation circuit and the construction of an acid leaching plant."

Jan 1, 1977

By Mario E. Rossi

The full economic evaluation of a mining project requires a block model that provides an estimate of the tons and grades of available resources. The model must be representative of the mineralization to be found at the time of mining for specified extraction periods and within acceptable error margins. In an operating mine, there may be a reasonable understanding and estimates of actual dilution and ore loss. This paper discusses the issue from the perspective of a project at a feasibility or preproduction level of development. Three types of dilution are discussed. Internal dilution (or change of support) is function of the spatial distribution of the mineralization and its relation to the operation?s selectivity. Geologic contact dilution is the unavoidable mixture at contacts or boundaries of material with different geologic characteristics, grades, or metallurgical performance. Operational planned and unplanned dilution should also be considered, sometimes incorporated by factoring the resource model, but more accurately by mimicking the grade control process. The resource estimation process always carries uncertainty, which is sometimes significant, and usually caused by several factors. These include quantity and quality of drill hole information; quantity and quality of geologic data; grade estimation methodology; dilution and mining recovery factors applied; etc. A key decision is to whether estimate as accurately as possible the in-situ geologic resource or to estimate the tons and grade of the material to be fed to the processing plant. The geologic modeling and grade estimation methods used are conditioned by this decision.

May 1, 2009

By K. Bruce Hodgins

The North American mining industry faces challenging emissions regulations in coming years with the introduction of new standards for off-road diesel engines. In order to remain competitive, industry stakeholders must invest in new technologies that are economically and environmentally sustainable. Westport Innovations Inc., of Vancouver B.C. has developed high pressure direct injection (HPDI) technology that allows diesel engines to run primarily on natural gas with no intrusive engine modifications, reduced emissions of NOx, PM, and CO2, with no loss in performance. This is accomplished through late-cycle high-pressure injection of natural gas directly into a diesel engine combustion chamber. The natural gas is injected at the end of the compression stroke. A small amount of diesel fuel is injected first to initiate combustion, followed by the main natural gas fuel injection. The diesel cycle and its operating characteristics are fully retained including high combustion efficiency, low speed torque, high-power output, no engine knock and fast response to load changes. Natural gas has not been an attractive fuel alternative in mining operations due to reduced performance associated with spark ignition engines and the added weight and space required for compressed natural gas tanks. However, liquefied natural gas (LNG) can be stored in a similar manner and volume to diesel fuel by virtue of its increased energy density over compressed natural gas. Cummins, Inc. of Columbus, Indiana and Westport have formed a joint venture, Cummins Westport Inc. (CWI), under which agreement the HPDI technology is being applied to a Cummins QSK engine series for high horsepower applications such as mine haul trucking. CWI, along with Komatsu Mining Systems, ENRG Fuels, Placer Dome, and Cortez Joint Venture are performing a feasibility study for the development and demonstration of an LNGfueled HPDI QSK engine in a large mine haul truck. The goal would be to demonstrate low emissions consistent with EPA ?Blue Sky? standards, high efficiency based on HPDI technology and good economics resulting from the high fuel consumption of 2,000+ hp trucks.

May 1, 2002

By S. Stefanizzi

In the present paper, numerical simulations based on a finite/discrete element approach are used to study deformation and failure process during standard rock mechanics. FEM/DEM modeling has been used as available with the ELFEN code, which explicitly model the transition from continuum to discontinuum. The transition is simulated through a crack nucleation and propagation that obeys to the Griffith?s failure criterion. If the fracture criterion within the intact rock (represented by FEM) is met, a new crack (represented by DEM) is initiated. Remeshing allows the fracture process through the FEM mesh to be tracked and visualized, thus contact properties can be assigned to pre-existing fractures and newly generated fractures. In this study, compressive tests of rock samples are simulated. The applicability of ELFEN to properly and efficiently simulate typical laboratory rock mechanics tests, with reference to the rock fracture process, is described in detail. In addition, an indirect validation of the extensional strain criterion proposed by Stacey (1981) is given.

May 1, 2009

By Euler De Souza

Backfilling in Canadian mines has been practised for close to 100 years and evidence anticipates the application of mine fill technology at an increasing rate during the foreseeable future. The evolution of backfill technology is closely related to the advancement of modern mining methods and the development of new backfill technology continues to evolve. The authors, after conducting extensive surveys of backfill practices in underground mines across Canada, have concluded that, because backfill operations employ large quantities of cement and experience large costs associated both with backfilling practice and cement use, opportunities exist for reducing backfill energy costs and enhancing the application of alternative cementing agents in backfill. Consequently, the authors have developed an alternate, equally effective and lower cost binder agent replacement for cement, and incorporated waste glass into the development of a lower cost backfill (glassfill). This paper presents the results of two design stages associated with the development of glassfill: strength development and flow performance. The advancement of this technology has reached a stage that should promote industrial implementation within the Canadian mining industry. A number of Canadian mining operations exhibit potential for plant optimization through possible binder source replacement, and might thus realize associated reductions in backfill and energy costs.

Apr 1, 2005

By A. F. Banks

"Potash processing has much in common in terms of unit operations and plant operating strategy with other mineral processing plants. As it is a rather large topic the processes will be broad brushed to give you some background and then I will go into a little detail on the things we do in the Cominco plant that may be of interest to the group as a whole. In particular the centrallized computer control system and associated instrumentation and the operator training programs will be covered as well as the mill fire, something that could happen in any plant. THE ORE AND PRODUCTSThere are differences in potash ores as you would expect. It is my intention to deal with the ores processed in the Saskatoon area. These are mined from the beds in the Patience Lake Member and have a mineralogical description as follows:Sylvite (Potassium Chloride) 40%Halite (Sodium Chloride) 55%Insolubles (Slimes) 5%A number of products are made from this ore. It is characteristic of a potash plant that you put as much effort into grading and converting the sylvite to meet market requirements as you do in recovering it."

Jan 1, 1976

By H. E. Urtubia

"BHP-Billiton’s Minera Escondida Limitada, in Chile, is one of the world’s largest copper producers. It treats a combined 10,500 tph of copper ore through its two concentrators: Los Colorados and Laguna Seca. The performance of the rougher circuit at each concentrator was measured and analysed using the JKTech flotation optimisation methodology. This involved developing a flotation model for each concentrator based on cell operating parameters (for example bubble surface area flux and froth recovery) and feed ore floatability characteristics. The rougher circuit performance was evaluated in terms of traditional measures, such as grade and recovery. The operation was also analysed using the measured cell operating parameters and ore floatability and the effect of these with regard to performance (grade / recovery) was assessed.This paper presents a comparison of the rougher circuit at each concentrator in terms of these parameters. The main differences in rougher circuit performance between the two plants were attributed to differences in feed ore floatability characteristics and froth recovery. The comparison highlighted opportunities where performance improvements could be made. The study also showed the usefulness of separating the flotation process into easily measurable subprocesses to further identify the different mechanisms occurring in each rougher circuit. Traditional measures like grade and recovery are useful for monitoring flotation operation but this data lacks the depth to determine the root cause behind operational issues. Determining the operating parameters and ore floatability provides the operating plant metallurgist better tools to assess and manage these issues."

Jan 1, 2006

By M. R. Hegge

The Jabiluka One and Two uranium deposits occur in Lower Proterozoic metasediments of the Cahill Formation, which is part of the Pine Creek Geosyncline in the East Alligator River area, Nothern Territory. The Jabiluka One deposit coincides with a "window" through unconformably overlying Middle Proterozoic sandstone of the Kombolgie Formation; Jabiluka Two is completely covered by that sandstone. The observed part of the Cahill Formation exhibits four horizons which are favourable hosts for uranium mineralization. These have been folded into an east-southeast-striking, gently plunging, open asymmetric syncline-anticline structure. The host rocks are mainly chlorite and/or graphite schists and their brecciated equivalents which have undergone initial regional prograde metamorphism to the amphibolite facies, then retrograde metamorphism to the greenschist facies. Mineralization consists of pitchblende, mainly filling open spaces and to a lesser extent in disseminated form. Chlorite, pyrite and quartz are commonly associated with the uranium mineralization. A portion of the Jabiluka Two deposit contains economic concentrations of gold. Structural preparation with low-pressure conditions at these sites appears to be the most significant ore control. Genetic hypotheses favour initial deposition in Lower Proterozoic sediments, followed by remobilization during later orogenic events. The deposits bear a marked similarity to some pitchblende deposits in central Canada.

Jan 1, 1977

By A. Demirci, A. Keçeciler, Y. S. Durutürk

"This paper deals with the results of the variation of thermal conductivity of rocks with pressure on a laboratory scale. For this purpose, the authors have added a pressure-supplying unit to the apparatus developed by Mousset-Jones and McPherson (1986), Önder (1995), Ashworth and Ashworth (1979), and Innaurato and Occella (1989) in order to measure the thermal conductivity under pressure. The values obtained from the tests performed by this new apparatus have been stated using a regression analysis and the related graphs have been drawn. Results have shown that the thermal conductivity of rock varies digressively with pressure. The same results have been obtained in different rocks types. IntroductionOne of the most important tasks of mining engineers is that of establishing, maintaining and sustaining safe and healthy working conditions in underground mines.Heat can have a profound effect on safe and healthy working conditions and is one of the main problems in deep underground mines. In this regard, the temperature of the air passing through the mine openings increases steadily and causes a decrease in the efficiency of workers due to the unwanted physical effects to human bodies in the working area. At the same time, the hot and humid environment resulting from heat and temperature rise causes some important occupational diseases and increases the accident risks in the related openings."

Jan 1, 2002

By S. Yalcin, S. Chang, M. Oliazadeh

"Present day ferrochrome demand is on the rise, as more steel products require this material as an alloying element. It is projected that the stainless steel demands will grow by about 6% per year to 2020; as such, the supply and demand for ferrochrome appears promising. Chromite is the only economical source of chromium, which is commonly upgraded by gravity techniques and used to produce ferrochrome. The gravity separation methods are not able to treat particles finer than 0.1 mm efficiently. Therefore, in processing chromite ore, a large quantity of fine tailings; some 25% of the mineral values have been reported as lost in slimes during processing. The chromite content of these tailings is typically 10-20% Cr2O3 and accumulates into a large stockpile/pond. A chromite concentrator project in Canada, considers a cut-off grade of 20% Cr2O3. This indicates further processing might be required to recover chromite from low-grade stockpile when the high-grade deposits are depleted. Low-grade ores normally indicates disseminated chromite ores with low liberation and consequently fine comminution. This paper reviews the techniques for treating chromite from fine material and provides some examples of successful operations in fine chromite recovery. Beneficiation techniques for fine particles include gravity separation, magnetic separation, and flotation. Several case studies are presented here that used one of the aforementioned methods or a combination of them.INTRODUCTIONChromium is one of the essential element and important material for production of ferrochrome alloys and special steel. Chromium occurs as chromium spinel, a complex mineral with chemical composition of (Fe, Mg) O (Cr, Al, Fe)2 . Chromite ore is exclusively found in ultramafic igneous rocks. Major associated gangue minerals are talc, quartz, serpentine and iron oxides.Chromite is a heavy mineral, with a specific gravity in the range of 4-5, relative to associated gangue minerals in a chromite ore, which makes gravity concentration a suitable process. This is generally true for coarse particles, ranging from 1 mm to 100 mm. Typically, the ore is prepared by crushing (and grinding if necessary) to a suitable size and the material is sized for the appropriate beneficiation techniques. It is common to use heavy medium separation (e.g. dense media drums, dense media cyclones, or Dyna Whirlpool) to treat coarse size and intermediate size particles (1 – 100 mm). Intermediate and fine particles (20 – 0.1 mm) could be treated by jigs. Spirals, shaking table, sluices, and Reichert cones can upgrade fine particles. Figure 1 shows a typical chromite beneficiation process flowsheet. As can be seen, it consists of three major sections: feed preparation (crushing, screening), de-sliming, and concentration. Beneficiation recoveries range from 80 to 85%, although the ratio of upgrading is only 2 to 3."

Jan 1, 2013

By A. J. Magerowski

Energy consumption is a main component of operational costs for the comminution of mineral bearing ores. Reduction of energy consumption has continually been addressed by mill operators and equipment manufacturers. Our testing over the last few years strongly indicates that the overall energy needed to comminute a mineral bearing ore can be brought down significantly, if more work is done in the crushing stages of the comminution circuit.This calls for uprating of the conventional crushing equipment into a new generation of crushing equipment to produce finer products. This will result in the emergence of new ideas in the design and application of equipment and corrnninution circuits.

Jan 1, 1986

By A. Vien, B. C. Flintoff, R. P. Edwards

"A major thrust in industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements in control performance can be achieved by getting back to the basics.IntroductionEvery modem concentrator has a state-of-the-art computer control system in place. Several of these are contemplating installing, or have installed, advanced control systems, such as expert systems, but the foundation of their control system remains the PI controller. Although the authors are not aware of any survey or published information for the mineral processing industry, it is reasonable to assume that it would be similar to the pulp and paper industry. ""The average [pulp] mill has some 2000 control loops of which 97% use PI control. This means that PID, dead time compensation, adaptive controllers, specialized algorithms, ... , constitute only 3% of the installed base."" (Bialkowski [1992]).Bialkowski [1992] also stated that ""If you have been keeping score, only 20% of the loops surveyed actually decrease variability in automatic over manual mode of operation, in the short term."" He attributed the problems to: poor tuning (30% of all loops), control valve problems (30% of all loops) and process problems (20% of all loops). There appear to be a serious need to go back to basics and review the existing control system."

Jan 1, 1998

By J. C. Bothan

A program to provide technical in-formation on the use of fuels in pyro-metallurgical processes, from the Canadian fuel viewpoint, was initiated about five years ago by a Canadian Institute of Mining and Metallurgy liaison grou1> composed of members from the Coal Research Committee of the Coal Division and the Iron and Steel Committee of the Metallurgy Division. This paper is another of a series prepared for this program. Previous papers included a review of pyrometallurgical processes of Canadian interest, a survey of ferrous processes relevant to the development of an integrated steel industry in western Canada and a survey of the fuel requirements of the non-ferrous metals industry in Canada. It is widely recognized among per-sons familiar with the Canadian coal industry that, because of the large resources of coking coal in western Canada, the

Jan 1, 1963

By Peter Raziszewski

"A ball charge dynamics model is presented. Simulation results are compared with observed data showing good correlation. Based on the charge dynamics models, a liner wear model is presented along with some wear simulation results. Using the charge dynamics model with the liner wear model, it is possible to envision the predictions of mill power consumption as a function of liner wear. Further work is needed to validate the liner wear model.IntroductionFrom a process control point of view, industrial systems can be considered stationary or non-stationary. For example, the physical properties, such as geometric and/or material, of a system considered stationary do not change with time. However, this is not true for non-stationary systems such as those found in the mining industry where process dynamics are often violent with wear being an intrinsic process phenomenon.In this paper, a model for ball charge dynamics will be presented along with a description for liner wear. Simulation results for power draft prediction using the charge model will be compared with observed data. Further, liner wear results will also be presented."

Jan 1, 1997

By B. Simser

Noranda?s Brunswick mine is a 10 000 t/d producer of lead-zinc-copper-silver ore that has been in operation since 1964. Mining of this multiple lens deposit is primarily by blasthole stoping techniques between 400 m and 1200 m below surface. The combination of a high overall extraction ratio, an overall steeply dipping tabular shape, and high horizontal stresses (twice the vertical) have elevated the induced stress regime to levels comparable to much deeper operations. Improved mine design, and a better understanding of how the rock mass responds to mining in high-stress environments is essential to improve overall recoveries and maintain safety. Seismic monitoring has proven to be an essential tool at Brunswick, for both short-term safety of workers, and long-term strategic planning. Practical case studies illustrate how seismic data, particularly source parameter information, can be used to measure the rockmass response to mining and improve mining layouts in difficult regions. As the global trend continues toward mining in deeper, higher stress environments (e.g., South African Witswatersrand Basin, Sudbury Basin) and as local extraction and thus ground stresses continue to increase in existing deposits, seismic monitoring will play a critical role in mining safely and economically.

May 1, 2004

By B. Simser, V. Falmagne

"Noranda’s Brunswick mine is a 10 000 t/d producer of lead-zinc-copper-silver ore that has been in operation since 1964. Mining of this multiple lens deposit is primarily by blasthole stoping techniques between 400 m and 1200 m below surface. The combination of a high overall extraction ratio, an overall steeply dipping tabular shape, and high horizontal stresses (twice the vertical) have elevated the induced stress regime to levels comparable to much deeper operations. Improved mine design, and a better understanding of how the rock mass responds to mining in high-stress environments is essential to improve overall recoveries and maintain safety. Seismic monitoring has proven to be an essential tool at Brunswick, for both short-term safety of workers, and long-term strategic planning.Practical case studies illustrate how seismic data, particularly source parameter information, can be used to measure the rockmass response to mining and improve mining layouts in difficult regions. As the global trend continues toward mining in deeper, higher stress environments (e.g., South African Witswatersrand Basin, Sudbury Basin) and as local extraction and thus ground stresses continue to increase in existing deposits, seismic monitoring will play a critical role in mining safely and economically."

Jan 1, 2004

By Steven Townend

Mining-related activities have been known to create a challenging operating environment for mining companies located in close proximity to communities. Issues such as noise, vibrations from mining operations, land use and emissions are often a concern for community residents. In order to develop good community relationships it is necessary to take a proactive approach. This paper documents this approach and also deals with the social implications for Vale associated with mining activities in the heart of the community of Copper Cliff, Ontario, Canada.

May 1, 2011

By B. W. Smee

Glacial lake sediments or glaciolacustrine deposits form a significant portion of the Canadian, Scandinavian and Russian landscapes. Furthermore, 50 per cent of the Archean volcanic belts within the Canadian Shield area are covered wholly or in part by these deposits. Because of the high electrical conductivity and low hydraulic conductivity of these compact sediments, the application of geophysical (electrical) and geochemical techniques in such areas becomes a difficult task. The presence of these sediments has therefore hampered exploration for metallic sulphide deposits in some of the most important metallogenic environments of Canada. Similar problems exist in some tropical countries, such as Australia, where the overburden may be very conductive. In this paper, the extent and provenance of the glaciolacustrine deposits within the Canadian Shield are described. The geochemical and geophysical factors that hinder exploration in the clay belts are reviewed, with case histories of successful and unsuccessful applications of some of these techniques. The most successful geochemical technique used within glacial clay belts is the sampling of lodgement till beneath the clay cover, and the analysis of the heavy mineral fraction of that till. Surficial sampling has not been successfully applied. Some geophysical techniques, more specifically electromagnetic and magnetic induced-polarization techniques, have detected mineralization beneath substantially deep clay or saline overburden layers. Some suggestions have been made, such as the use of anions in hydrogeochemical surveys and the use of wide-band multi-frequency EM systems. When implemented, they will hopefully make the current geochemical and geophysical methods more effective in exploration for base metal sulphides within clay-covered terrains.

Jan 1, 1979

By G. Chi, W. J. Davis, S. Watters, D. Hoy, S. Castonguay

"The Poplar Mountain gold occurrence in western New Brunswick is hosted in the Poplar Mountain volcanic complex (PMVC), which is located along the southern segment of the regional Woodstock fault zone. The PMVC consists of three principal units including, in ascending order, a porphyritic felsic volcanic unit, a volcaniclastic unit, and a mafic volcanic unit. U-Pb dating of zircon indicates that the age of the volcanic rocks is younger than 459 ± 3 Ma, and 40Ar/39Ar dating of mineralization-associated sericite indicates that the age of mineralization is 411 ± 3.7 Ma. Gold-mineralized zones occur in all the lithologic units but mainly in the porphyritic felsic volcanic unit. Gold zones are not controlled by individual faults but are characterized by high-density brittle fracturing, thin carbonate-quartz veining, and intensive ankerite-sericite alteration, superimposed on an earlier chlorite-calcite- quartz alteration. Gold is associated with arsenopyrite, which mostly occurs as disseminations in the host rocks, and to a lesser extent with quartz-carbonate-sericite veins and quartz-cemented breccias.Geochemical data indicate that mineralization-associated alteration is characterized by enrichment of K, Rb, Cs, Ca, Sr, Ba, As, Sb, W, C, and S. Fluid inclusion data indicate that the mineralizing fluids are composed of H2O, salts, and CO2 with variable amounts of N2 and CH4; salinities range from 2.3 to 10.6 eq. wt.% NaCl, but mainly from 2.3 to 5.6 eq. wt.% NaCl, and homogenization temperatures lie mainly between 220° and 270°C. Fluid pressures at the site of mineralization are estimated to have been 770 to 1200 bars, corresponding to a depth of 2.9 to 4.6 km at lithostatic pressure. The d18OSMOW and d13CPDB values of mineralization-related ankerite range from +14.5‰ to +16.5‰, and -6.8‰ to -8.3‰, respectively. The d18O values of the ore-forming fluids are estimated to be 6.4‰ to 8.3‰ at a temperature of 250°C. These carbon and oxygen isotope data fall in the field of magmatic fluids and in part the field of metamorphic fluids.Considering the geological setting of the region, abundant granitic intrusions, the similarity between the age of mineralization (411 ± 3.7 Ma) and the nearby Pokiok batholith (402-415 Ma), and the enrichment of granophile elements in mineralization-related alteration, the ore-forming fluids were probably derived from a granitic intrusion underneath the PMVC. These fluids were focused along structures related to the Woodstock fault. The Poplar Mountain gold occurrence might be compared to some granitic intrusion-related gold systems based on the geochemical data presented herein. L’indice aurifère de Poplar Mountain dans l’ouest du Nouveau Brunswick est contenu dans le complexe volcanique de Poplar Mountain (CVPM), lequel est situé le long du segment sud de la zone de faille régionale de Woodstock. Les trois unités principales du CVPM sont, de la base au sommet, une unité volcanique felsique porphyrique, une unité volcaniclastique et une unité volcanique mafique. La datation U-Pb de zircons indique que les roches volcaniques sont plus jeunes que 459 ± 3 Ma, et la datation par la méthode 40Ar/39Ar de séricite associée à la minéralisation assigne à la minéralisation un age de 411 ± 3.7 Ma. Bien que les zones minéralisées en or soient présentes dans toutes les unités lithologiques, on les retrouve surtout dans l’unité felsique porphyrique. Les zones aurifères ne sont pas contrôlées par des failles individuelles mais sont caractérisées par une grande densité de fractures cassantes, de minces veines de quartz-carbonate, et par une altération en ankérite-séricite intense qui se superpose à une altération antérieure en chlorite-calcite-quartz. L’or est associé à l’arsénopyrite, laquelle est principalement présente à l’état de disséminations dans la roche hôte, et à un moindre degré avec des veines de quartz-carbonate-séricite et des brèches à ciment de quartz.Les données de géochimie indiquent que l’alté"

Jan 1, 2008

By Scott G. Honan, Wayne F. Luinstra

"Since 1992, the concentration of gold using gravity methods has progressed to become an important part of production at Hemlo Gold's Golden Giant Mine. Currently, the gravity circuit accounts for approximately 25% of the Golden Giant Mine's Gold production. This circuit consists of a 30 inch Center-Drain Knelson Concentrator and a Shaking Table. The evolution of gravity concentration will be discussed with an emphasis on the economic justification for a gravity circuit as well as the practical aspects and metallurgical impact of operating such a circuit. It will be demonstrated that the operation of a gravity circuit has definite benefits to the operation of the Golden Giant Mill and will continue to play an important role in future gold production.1.0 IntroductionHemlo Gold Mines Inc. Golden Giant Mine is a 3000 TPD underground gold mine and milling facility located 40 km east of Marathon, Ontario. Mining is accomplished by means of sublevel longhole open stoping. The ore is processed using conventional crushing, 3-stage ball milling, conventional cyanidation and CIP processes. The mill and concentrator are described in more detail in other publications1,2.Since July of 1992, the Golden Giant Mine has been using a gravity circuit for gold recovery in the mill's grinding circuit. Despite the fact that gold recovery averages over 96% using conventional cyanidation and carbon-in-pulp processes, the gravity circuit has become an integral part of milling operations. This paper will discuss the economic justification for a gravity circuit as well as the practical and metallurgical aspects of its operation."

Jan 1, 1996