Search Documents

By Jan E. Nesset, Phillip J. Mackey, Joo Y. Kim, Giovanni Di Prisco, André R. Laplante

Understanding the appropriate gold recovery to associate with copper recovery when assessing laboratory testing on porphyry deposits is often complicated by several factors including variable and/or complex mineralogy, and the variability contributed by the low Au content of the various flotation products. As a result, gold recovery is often underestimated and the value contributed by the gold to project economics is less than it should be, a problem that could influence overall project viability. Typically, for these types of deposits, the gold recovery is found to be lower than the copper recovery. In this unique project, having the objective of seeking a better understanding of gold recovery relative to copper recovery, mill feed samples from a selection of six operating world-class Cu-Au low-grade deposits were collected along with the mill metallurgical results for the corresponding sample periods. The samples were subjected to laboratory flotation tests, as well as the Laplante gravity recoverable gold (GRG) test, mineralogical assessment and cyanidation leaching. The aim was to better understand the copper and gold recovery relationship, the links between laboratory and plant flotation performance, the influence of mineralogical differences, and the potential for enhancing gold recovery by gravity recovery techniques. A new correlation of copper and gold recoveries based on the results is presented in the paper. The results showed that the link between copper and gold recoveries established in the best laboratory tests were maintained in the plant results, and further, that the potential for improving Au recovery by gravity or flash flotation methods is directly proportional to the amount of gold greater than 75 microns.

Jan 1, 2005

By J. T. Furey

"A pilot plant study was conducted to evaluate the performance of column flotation in the recovery of gold from a gold/tellurides bearing sulphide ore, and to compare the performance of column flotation to conventional ""mechanically agitated"" flotation.Tests were conducted in a 60 liter glass column with ground flotation feed split from a concurrently operating conventional pilot plant, thus permitting direct comparison between the two processes. During the test program, the effects of wash water rate, gas holdup, froth depth, residence time and flow bias were examined in detail.The ore had an average ""as tested"" feed grade of about 5 g/t gold and 1 % sulphur, with the gold occurring primarily as inclusions of montbragite (Au2Te3) in pyrite, with minor amounts of native gold. Conventional flotation using 60 minutes residence time across four roughing stages recovered about 97% of the gold into concentrates grading about 50 g/t Au. A single stage of column flotation roughing using 25 minutes residence time matched the conventional circuit recovery of 97%, but produced grades of+ 150 g/t Au. INTRODUCTIONColumn flotation is the most significant innovation that has occurred in the mineral processing industry in recent years and has become an important alternative to mechanical flotation. Column flotation has been most widely accepted and applied in cleaning service where it has frequently proven to be superior to mechanically agitated flotation. Roughing in columns has not been ignored, but early testing indicated that columns may not be capable of achieving adequate recovery and, to date, columns have not been seen as serious competitors for mechanical roughers."

Jan 1, 1990

By O. Matwijenko

"The Kidd Creek concentrator is located twenty-six kilometres east of Timmins, Ontario, within a metallurgical complex including a 109,000 MTPY zinc plant and a new 59,000 MTPY copper smelter and refinery. A complement of 159 persons is employed in the operation of the concentrator.Ore from the Kidd Creek Mine is crushed underground to minus 15. 0 cm, then transported twenty-seven kilometres by rail 1:0 the concentrator. After being crushed to minus 1. 6 cm, the ore is further processed by grinding and flotation.The concentrator commenced operations in November of 1966 at a designed capacity of 8,200 MTPD. Two parallel flotation and grinding circuits treated copper-zinc ore (2.28% Cu, 5.63% Zn) and a third treated silver-copper-lead-zinc ore (230 g/MT Ag; 0.57% Cu, 0.88% Pb, 7.89% Zn).By 1975, the concentrator was treating 9,100 MTPD of ore. Seven concentrates were being produced, namely, high silve1: copper, low silver copper, lead, low silver zinc, high silver zinc, pyrite and tin.Planned minesite expansion to a second underground mine required increased concentrator throughput. Expansion of the concentrator enabling a thirty-three percent increase in copper-zinc ore throughput occurred during the period 1975 through 1978. This expansion included increased load-in capacity, major redesign in the crusher house, the addition of a fourth grinding and flotation circuit, the building of a fourth dryer, and numerous expansions of services."

Jan 1, 1980

By V. Songmene, R. Khettabi, J. Masounave, R. D. Njoya

L'augmentation régulière des règlements environnementaux et de la sécurité au travail deviennent de plus en plus strictes. L'usinage fait partie des opérations industrielles qui peuvent causer des problèmes de santé au travail et sur l'environnement. La plupart des particules de poussières produites pendant toutes les opérations d'usinage à sec ou lubrifie causent des nuisances environnementales graves. Le travail propose étudie l’influence des paramètres de coupe, des alliages et des états des matériaux sur la formation des copeaux et sur la génération de poussière lors de l'usinage à sec. Deux modes d'usinage (le fraisage et le perçage) sont abordés. Une loi reliant la ténacité des matériaux aux émissions de poussières est proposée. Les effets des matériaux et de leurs conditions, ainsi que des procédés d'usinage sur la génération des poussières ont été mis en évidence. Des mécanismes de formation de poussières sont identifiés et reliés à la formation des copeaux.

Jan 1, 2006

By P. Massi

"Wholly owned by the Coniagas Mining Company, the oldest continuously listed mining company on the Toronto Stock Exchange, St. Andrew Goldfields is located on Hwy. 101 approximately 30 miles east of downtown Timmins, Ontario. Geographically situated on the Porcupine-Destor Fault, the mine and mill in Stock township is positioned in the heart of Northeastern Ontario's goldmining communities.In July 1988, a 600 ft. shaft, hoist, and compressors were already in place when construction started on a 500 T.P.D. capacity C.I.P. mill and crushing plant.By June 15, 1989 the mill was commissioned and attained the design capacity by August of that same year. Since then, changes to the circuit have increased throughput to 900 T.P.D. from two significantly different ore sources.Meeting the Ministry of the Environment's guidelines is an ongoing commitment utilizing the Inca S02 process in line between the tailings pond and secondary polishing pond.INTRODUCTIONExploration on what is now known as St Andrew Goldfields' Stock Township Mine was carried out ln the early l960 1 s by Hollinger Mines Ltd. The property was acquired by Quebec Sturgeon River Mines 1n 1973 and the main shaft was started ill 1979.When St Andrew Goldfields was incorporated 1n 1983, exploration and development commenced to identify the ore body. The company decided 1n 1987 to bring the Stock township property into production after an extensive feasibility study and testwork at Lakefield Research in Toronto. Leslie Engineering was contracted to design, engineer and procure al 1. equipment from the coarse ore bin to the tailings distribution system and backfill plant"

Jan 1, 1992

By G. D. West, J. D. Purdue

"Marked Ball Wear Testing (MBWT) employs identified grinding balls which are placed in an operating mill for a period of time, retrieved from the mill, and then measured to determine the amount of wear experienced. This is an excellent method to evaluate the relative differences in the wear rates of various grinding ball materials and/ or manufacturing process variables simultaneously and under actual production milling conditions. This paper outlines the methods of ball identification, testing and evaluation procedures and discusses the strengths, weaknesses, and proper application of marked Ball Wear Test results. INTRODUCTIONThe consumption of grinding media in the mineral processing industry represents a substantial cost to the comminution process. Grinding media is most often found to be the second highest consumable cost next to energy. To determine the selection of the most cost effective media, one must determine the specific wear mechanisms present in a given grinding application and decide which media system addresses these mechanisms most economically.A MBWT has definite advantages over other methods used to evaluate the relative consumption rates of grinding media. It allows the comparative testing of a large number of different ball types under identical operating conditions in a very short period of time. In addition, production wear rates can be accurately predicted directly from MBWT results. Typical MBWT test periods are in the order of 350 to 700 operating hours for high wear rate application and upwards of 2000 or 3000 hours for low wear rate applications. These times are much less than the 5000 or more hours required to purge a mill of the incumbent ball charge (to convert it to the test ball) and then provide even a minimal test period in which to conduct a full production test, for just one type of ball. Under production test conditions the evaluation of competitive product or the development of improved grinding balls is necessarily slow."

Jan 1, 1991

By Martin Froehling, Curtis Mohns, Rahim Rajwani, Michael Fullam

"The Kemess mining and milling complex is operated by Northgate Minerals Corporation and is located in the mountains of north-central British Columbia, 430 kilometers northwest of Prince George. The complex consists of the Kemess South open pit mine and a 52,000 tonnes per day mill. Hypogene, supergene and leach cap ores are processed using conventional crushing, grinding, and flotation techniques to produce gold-copper concentrates with minor by-product silver value.The rougher flotation concentrate is re-ground in closed circuit before being cleaned to final concentrate grade. Historically, gold losses in the cleaner tailings were primarily associated with pyrite, with only minor amounts of free gold. More recently, with the processing of high pyrite ores, the major losses were found to be free gold less than 10 microns in size. The fine grind required for the high pyrite ores resulted in over-grinding of the free gold particles in the regrind circuit, contributing to poor flotation characteristics. It was thought that if this free gold could be recovered by gravity at coarser size in the regrind circulating load, the free gold losses in the cleaner tailings could be reduced.Preliminary test work carried out by Knelson Gravity Solutions indicated the potential for free gold recovery in the regrind circuit. A Knelson XD-30 Concentrator was installed with variable speed capability, and a series of optimization tests were carried out. In addition, cleaner tailings were characterized with gravity operating and with gravity not operating to determine the overall gold recovery benefit. The single Knelson XD-30 installation recovers ~10% of the total gold in the regrind circuit and increases overall recovery by 3% when high pyrite ores are processed."

Jan 1, 2007

By R. B. Throndycraft

"1. Belt-Drop Agglomeration Preferred at Heap Leach Operations. The agglomeration method now preferred at heap leach operations utilizes belt-drops along conveyors. Belt-drop agglomeration is being designed into numerous upcoming heap leach operations. It offers substantial capital cost savings over previously favored drum agglomerators. It has such significant operating and maintenance advantages that some drum agglomerators have been retired in favor of belt-drops.The majority of heap leach operations are now built with crushing included in the flowsheet. If crushing is included, belt-drop agglomeration can be added for almost no cost. The agglomeration equipment is simply a few conveyor transfers, designed to provide the tumbling and rolling action which forms the agglomerates. Controlled water sprays are needed at each of these agglomeration transfers. Cement or lime is added as a binder, to stabilize the agglomerates. This reagent is also needed to raise pH to safe operating levels.Addition of the pH control reagent before stacking the ore offers a reagent cost benefit. In the belt-drop mixing technique, the ore is intimately mixed with the lime (or cement). After stacking on the heaps, when the cyanide solution is sprayed onto the high-ph ore, very little cyanide is consumed. Without the pre-addition of lime or cement, the leach solution is sprayed onto neutral ore. The mixture of high-pH leach solution and neutral pH ore causes the solution pH to drop, releasing cyanide gas. This release is minor from a safety viewpoint, much less than dangerous, but the gas release is a costly waste of the cyanide reagent. Pilot-scale comparison tests were made at Pinson. Ore pre-treated with lime or cement showed 30% less cyanide consumption than untreated ore."

Jan 1, 1989

By J. K. Gowans

"INTRODUCTIONTo bring a mining property into production in the Canadian High Arctic a company must deal with the harsh environment, the short shipping season and the high cost of labour. In trying to minimize the effect of these factors, the concept of a barge-mounted process plant was investigated as an alternative to the conventionally built concentrator. Cominco's previous experience gained at the Black Angel Mine on Greenland's west coast suggested that this would be a practical alternative.The normal shipping season at Little Cornwallis Island is approximately six weeks long, from mid-August to the end of September. All equipment and materials must be delivered during this small ''shipping window."" The logistics problems are enormous; if the conventional approach had been used the major process equipment would have been delivered to Little Cornwallis Island at the same time as the completed barge actually was! Construction would also be starting at the start of the worst climatic conditions, the Arctic winter. Nine months production was gained by opting for the ""Barge"" approach.What the Arctic winters do to the shipping season, so do they affect the productivity and the cost of labour. Construction labour must come from southern Canada. Thus higher transportation costs and higher wage rates, with more overtime and incentives, increase the labour costs to approximately 50% over normal southern rates. Couple these rates with the lower productivity involved with men working in the extreme cold temperatures and the net effort is worth avoiding. A process plant being constructed in Southern Canada can take advantage of more accessible labour at lower costs, increased productivity and a faster construction schedule. The barge concept must still deliver the equipment and materials during the ""shipping window"" but it can in the completed form."

Jan 1, 1983

TRE ? worldwide leader in InSAR ? Spinoff of Polytechnic University of Milan ? Numerous patents for cutting edge technology (e.g. SqueeSAR?, PSInSAR?) ? Focus solely on InSAR with over 13 years experience ? ISO 9001 quality certification ? Powerful scalable parallel processor to handle all jobs What can InSAR provide for mining? An advanced suite of tools for monitoring ground deformation over mine sites: ? Deformation maps ? A dense network of measurement points ? Time series ? Cross sections of surface profile evolution

Aug 1, 2013

"Developing markets for western metallurgical coal have continued to stimulate considerable exploration activity in the Rocky Mountain foothills and to influence major segments of a wide-ranging carbonization R&D pro-gram. Adjunct studies have included expanded petrographie investigations.Coal preparation has• been principally directed toward utilization of prepared small coal and was, like much of the year's combustion work, strongly influenced by concern over atmospheric pollution. Particular attention has been given to desulphurization and to the suppression of pollutants in combustion systems.In the area of non-fuel utilization of coal, interest has centered on plant nutrients and on a series of coal-based carbons which, inter alia, possess utility as filtration media.Other projects included the development of improved sampling and analytical methods, investigations into the effect of storage on coal proper-ties and R&D in solids pipelining. In addition, a significant volume of basic 'uncommitted' research has been maintained."

Jan 1, 1968

By J. J. Baz-Dresch

"The Cannon Mine, a joint venture between Asamera Minerals (the operator) and Breakwater Resources, is located in the centre of Washington state at the eastern base of the Cascade Mountains. The mine complex is located three blocks south of the city limits of Wenatchee, part of an urban area with a total population of 47 000. The closest residence is 350 feet from the mine portal.The B-Neath zone is a narrow, high-grade, downward extension of the southern tail of the mine's main ore body, the B-North zone. It also underlies the northernmost portion of the B-West zone (Fig . I) . The ore is usually reasonably competent but completely surrounded by very weak rock consisting of shear zone and unsilicified sandstones and siltstones.The zone has maximum dimensions of 420 ft in thickness, 500 ft in length , and 200 ft in width . The economic reserves extend from the 70-ft elevation (elevation above sea level) to the 630-ft elevation and consist of about 1.3 million tons of geologic reserves (proven and probable) at an average grade of 0.33 ounces per ton.Acquisition and ExplorationInitial DiscoveryThe initial discovery of the B-Neath zone was made by Tenneco Minerals during July through September, 1984. Their 22-hole surface drilling program consisted of 18 200 ft of drilling. Tenneco Minerals had acquired the 91/2 acre lease from United Mining Corporation.Asamera Minerals subsequently purchased Tenneco's lease in July, 1985; Tenneco retained a royalty position which was later purchased by Echo Bay Mining.Follow-up drilling by Asamera Minerals consisted of both surface and underground drilling. Eight surface holes (7200 ft) were drilled commencing in December, 1985. Following evaluation of the geologic data, an access drift was driven on strike along the top of the ore zone on the 500 level. Diamond drilling from this platform consisted of 17 200 ft in 79 holes."

Jan 1, 1990

By Denis Thibodeau

The selected mining method for the Rodeo lower Zone is slot and slash. Initial design indicated that the stope height should be limited to a maximum of 18 m, thus six levels were needed to extract the ore. Higher stope height in the Rodeo Lower Zone means less development thus less capital required to extract the available reserves. It was proposed to eliminate one level by establishing 30 m and 24 m level intervals. To ensure that no stability problems will be encountered by eliminating one level, a Matthew analysis, based on diamond drill core information, was performed for the Lower Rodeo Ore Body. In addition, comparisons between the rock mass quality of Meikle Main Zone below 1825 L and Meikle East Zone between 1600 L and 1750 L with the rock mass quality of the Lower Rodeo were made

May 1, 2002

By Hu Harries

WE RECENTLY completed a study for a client, who is an applicant to export gas from the Province of Alberta, on the effects of gas export on Alberta's economy. This study was part of the client's application ?before the Conservation Board, and, no doubt, some of you are familiar with it. Submissions by other applicants in earlier hearings before the Board and before the Royal Commission on Energy, as well as claims made by parties opposing export, have also brought forward a number of other opmwns regarding possible economic effects. Ali of these studies have been on a piecemeal basis. They have dealt with particular aspects of particular applications, and only indirectly and by inference with the overall question of gas ex-port. We have prepared this paper to review the overall picture and ex-amine, as far as time permits, all sides of the question. While the paper is entitled Economic Effects of Gas Export on Alberta, we felt that the area considered should in-elude northeastern British Columbia, not only because Westcoast, the first major gas export project, is essentially a northeastern B. C. project, but because this area has historically been, from the point of view of economic, if not of political, geography, part of Alberta. In this paper, when we talk of export, we mean export from the Province or, in this case, from Alberta plus northeastern B. C. Sales to other parts of Canada have exactly the same effect on the economy of this area as l1ave sales to the United States, provided, of course, they are made on equal terms.

Jan 1, 1958

By D. R. Lentz, C. J. Beaumont-Smith, S. H. Mcclenaghan

"Abstract - The Louvicourt Au-Ag-Cu-Zn-Pb sulfide deposit is hosted by a Middle Ordovician calc-alkaline sequence of aphyric rhyolite flows and associated fragmental rocks at the top of the Flat Landing Brook Formation. The Zr/TiO2 (average = 0.110) and Y/TiO2 (average = 0.021) ratios in the footwall felsic volcanic rocks are consistent with known values for the Reids Brook member. The deposit consists of two concordant lenses of semi-massive to massive sulfides, approximately 150 m long and up to 9 m thick, which represent a fold repetition of a single exhalative horizon. The deposit contains a geologic resource of 136 000 tonnes grading 1.2% Pb, 1.0% Zn, 0.4% Cu, 90.9 g/t Ag, and 0.96 g/t Au; the deposit locally contains elevated Au (2.9 ppm) and Ag (320 ppm) contents. A laterally continuous iron formation that contains barite caps the deposit, and is gradational vertically and laterally into laminated siltstone. The exhalite confirms the stratiform nature of this deposit, but a large percentage of sulfides occur as late replacements of altered felsic fragmental rocks in the footwall. Abundant examples of colloform pyrite and perlitic and spherulitic textures in volcanic clasts are well preserved. The base- and precious-metal content of the Louvicourt deposit is atypical of the Bathurst Mining Camp (BMC). Reported assay data (n = 27) indicate an average Pb/Zn ratio of 2.6, the highest in the BMC (average = 0.39). Lead exhibits a strong Spearman Rank correlation (r' = 0.92) with base metals throughout the sequence, indicating a preponderance of galena in both the stockwork and stratiform zones. The Ag and Au contents in this deposit are among the highest in the BMC and exhibit a Au-Ag- Cu-Pb association. Barite-rich exhalative pyrite exhibits a moderate Au correlation with Ag (r' = 0.77; n = 10) and Cu (r' = 0.76) and occurs in portions of the exhalative sulfides that are enriched in Pb. Chemical exhalative rocks are conformably overlain by trachy-andesitic volcaniclastic (possibly pyroclastic) rocks that are assigned to the Little River Formation. These are enriched in Nb (average = 38.4 ppm) and P2O5 (average = 0.17 wt.%), and have much lower Zr/TiO2 (average = 0.056) and Y/TiO2 (average = 0.0062) relative to rocks higher in the hanging wall. The intermediate volcanic rocks are conformably overlain by massive to pillowed basalt flows and related hyaloclastite that have Nb/Y = 0.60 and high TiO2 contents (average = 2.8 wt.%). This chemistry is consistent with rocks of the Brunswick Mines member (Little River Formation), except that these rocks are considerably enriched in P2O5 (average = 0.82 wt.%). This syngenetic exhalative deposit is unique for the BMC with a high Pb/Zn and elevated Au and Ag contents, as well as an epithermal signature (Sb-Ag-Au-Tl-Hg), analogous to high sulfidation volcanogenic massive sulfide deposits. Its intimate relationship with an emergent felsic dome (Flat Landing Brook Formation), chlorite-silicate-oxide-sulfide exhalite (locally hematitic), and the abundance of barite are classical features of many of the Kuroko deposits."

Jan 1, 2006

By Emilie S. Williams

The Doyon Mine?s Zone 1 (Altered Zone), found along the southern boundary of the mine, encompasses approximately 20% of the mining reserves. The mineralisation is found in a series of steeply dipping narrow veinlets, which are contained in an extremely weak host rock: a sericitic schist with RQD values ranging from 0 to 20. Longhole mining methods are used, with either longitudinal or transverse approaches, depending on the width of the ore zone. Dilution is of critical importance in the mining of this zone, particularly in longitudinal stopes, where dilution levels have averaged 55% since 2000. Major factors influencing dilution in this zone include the stope geometry and standup time. A two-phase approach has been developed to mine and backfill longitudinal stopes: the top of the stope is pastefilled after approximately half of the broken ore has been extracted; the remainder of the ore is extracted once the plug has cured; and the remaining void is filled. This method has been used in six stopes to date, resulting in an average dilution of 17%. This paper details the application of this technique and its effect on dilution.

Oct 1, 2004

By E. R. Packer

"The mill of Anaconda Britannia Mines is located on the eastern shore of Howe Sound, approximately 32 miles north of Vancouver, British Columbia. The mill has a daily capacity of 3400 to 3500 tons and at the present is treating chalcopyrite-pyrite ore from which only the copper mineral is concentrated. For a clear conception of concentrate filtering and shipping practice at Britannia perhaps a bit of past history should be related.For many years the mill concentrated copper and zinc minerals and intermittently a pyrite concentrate was produced. It was general practice to ship copper concentrate by towed barge down Howe Sound, across Juan de Fuca Strait and thence down Puget Sound to Asarco's smelter at Tacoma, Washington. Zinc concentrate was loaded in hopper bottom rail gondolas spotted on rail barges and towed to rail heads in Vancouver, thence by rail to Anaconda Reduction Works in Great Falls, Montana. Most of the pyrite produced was shipped by ocean freighters to Japan and Taiwan with an occasional barge load of 2000 to 4000 tons to nearby customers in Vancouver and the state of Washington.In recent years, because of smelter shut-downs for one reason or another, mostly strikes, a considerable amount of copper concentrates has been shipped by ocean freight to Japan and in 1971 several lots were loaded in gondola cars and shipped by rail to the Anaconda smelter in Anaconda, Montana, because Asarco's smelter was forced by municipal and state anti-pollution laws to limit the amount of S02 emission from the smelter stacks. Zinc concentrate production was halted in the early part of 1Y70 because of zinc depletion in the ores and pyrite production was stopped in May, 1971, because of a lack of markets.Filter equipment in the Britannia mill consists of conventional disc vacuum filters and reciprocating vacuum pumps. The copper concentrate filter was installed in 1923 as a 6 x 8'6"" American disc type manufactured by United Filter Corporation, The zinc concentrate filter, now converted as a spare for copper concentrates, is also a 6 x 8'611 American disc manufactured by Traylor Engineering and Manufacturing Company and was installed the same year. Formerly, there were, in addition, two 4 x 6' disc filters for pyrite and two 6 x 6' disc filters to de-water bulk flotation concentrates ahead of the regrind mills. Installed vacuum pumps were two Ingersoll Rand 22"" x 811 and one 22"" x 9"". One of the smaller machines has since been scrapped.At the time of the writer's transfer to Britannia in 1965, the entire filter system was operating as a unit using two vacuum pumps and a common filtrate tank with a 2"" SRL filtrate pump for five operating filters. The regrind and pyrite filters were in continuous operation and the co11p('r concentrate filter alternated with the zinc concentrate filter because both copper and zinc concentrates were transp0rted to storage by the same conveyor belt."

Jan 1, 1972

By Gerardo Vargas

Without an adequate data sample there can be no Reliability Analysis (RA). Without analysis there can be no systematic, verifiable improvement in reliability or in operational economy. A sample is a collection of life cycles. A beginning and ending event define a failure mode life cycle. Well known obstacles impede the reliability engineer in his role to analyze maintenance data. The main problem lies in the difficulty to obtain analyzable data samples. Although modern Computerized Maintenance Management Systems (CMMSs) should provide the needed information they rarely deliver samples of adequate quality. Cerrejon, an integrated mining operation in Colombia, South America solved the information management problem by applying a "Living Reliability Centered Maintenance (LRCM)" process to its fleets of Trucks, Graders, Dozers, Loaders, and Shovels. This paper describes a method wherein completed work orders capture reliability analysis enabling information. The 'right' maintenance observations reference significant failure modes. Work orders link to records in a continuously growing Reliability Centered Maintenance (RCM) structured knowledge base. Grouped and filtered knowledge-to-work order links, being instances of failure modes, provide the samples required by reliability analysis software tools and methods. LRCM software and related procedures facilitate the growth of knowledge, manage the work order-to-RCM relationship, and generate samples for subsequent reliability analysis.

May 1, 2011

By James S. Redpath

"AbstractThis paper is an attempt. to outline the present status of underground mining contracting in Canada, and to present certain facts concerning the writing and administration of underground mining contracts which, hopefully, may be useful to those intending to engage a mining contractor . The paper is based on the author' s experience as a contractor and also as a consulting engineer advising others in the purchase of contractors' services.HistoryIN THE early days of mining contracting in Canada, the contractor was primarily a labour contractor. He was expected to bring a good crew of men that normally followed him, and to perform certain work under his own direct supervision. The owner usually looked after all other details including financing, payrolls, withholding taxes, etc , computing and paying the contractor his profit. In the pre-World-War II years, most work was done on this basis.Over the years, the contractor was called on to supply more in the way of services, and the present-day situation evolved.Labour contracts are still used, but now the contractor is expected to carry out his own administration. Most contracts now call for the supply of special tooling required to do the work. In most cases, some, if not all, supplies are the contractor 's responsibility and , in a growing number of cases, the contractor is responsible for such items as design and surveying. The ultimate in this direction is the execution of projects on a turnkey basis. Under this system , the contractor carries the project to a stage where it is turned over fully operational to the owner."

Jan 1, 1977

By K. J. R. Ford

"Significant advances in mining and metallurgical operations have occurred over the last two decades, to define ore bodies via geological mapping, mineralogical analyses, geostatistical models and resource reserve modeling. Metallurgical process measurement, controls and modeling have also significantly progressed, with advanced instrumentation, control software, data capture systems and simulation tools. This progress together with development of the science of geometallurgy has allowed geologists, mineralogists, miners and metallurgists to start working together to define geometallurgical ore units and link these to mine planning and projected metallurgical performance. However, application of full geometallurgical programs into existing mine-processing operations or into new “greenfield” projects has been slow. This is mainly due to higher costs, limited dedicated technical resources and little or no corporate leadership. Additionally, life-of-mine cash flow models, the “dollars”, have been largely driven by ore tonnage rates, pay-metal grades and fixed pay-metal percentage recoveries, with few or no geometallurgical parameters included.Here defined, the “electrons” represent intrinsic ore characteristics embracing chemical composition, mineralogy, gangue components and their associated fundamental metallurgical processing phenomena. With its ever expanding treasure chest of measurement and modeling tools, geometallurgy paints a much clearer picture of the “electrons” for the geologist and metallurgist. But to fully understand and realize the real net value of ores over the life of a mine, a comprehensive link of “electrons to the dollars” is essential. Intrinsic characteristics of geometallurgical ore units are by definition linked to their metallurgical processing, but importantly need also to be related to operating costs, capital requirements and revenue.This paper discusses this important linkage under topics of ore geology and mineralogy, metallurgical processing, waste disposal, environmental issues, metal refining, project engineering and lifeof- mine models. Topics are illustrated by multi-metal references and by case examples from gold ore heap leaching and manganese ore smelting projects. 1"

Jan 1, 2013