Search Documents

By David Seaman, J-P Franzidis, Emmy Manlapig

"A new device has been developed to directly measure the bubble loading of particle-bubble aggregates in industrial flotation machines, both mechanical flotation cells as well as flotation column cells. The bubble loading of aggregates allows for in-depth analysis of the operating performance of a flotation machine in terms of both pulp/collection zone and froth zone performance. This paper presents the methodology along with an example showing the excellent reproducibility of the device and an analysis of different operating conditions of the device itself.The device has been used to investigate the froth selectivity of attached particles. Simultaneous measurements were made using a different froth recovery measurement technique in the same flotation cell. A comparison of these techniques shows that in this case, particles are selectively detached from bubbles at or near the pulp-froth interface.INTRODUCTIONA flotation cell can be considered to operate in two distinct phases or zones; namely the pulp or collection phase and the froth phase. The pulp zone is responsible for the formation of hydrophobic particle-bubble aggregates, whilst the froth phase is responsible for the separation of these aggregates from surrounding suspended hydrophobic and hydrophilic particles. Thus, the froth phase is the grade determining phase in flotation. A measurement of the bubble load (the mass of particles attached to air bubbles in units of mass/volume) will enable the analysis of the performance of both the collection zone at creating bubble-particle aggregates and also the froth zone at separating these aggregates from surrounding pulp.A measure of froth zone performance that has been used extensively in flotation research is the Froth Recovery, Rf, of a particular system. Froth recovery is defined as the mass of particles collected in the concentrate launder by true flotation as a fraction of the mass of particles entering the froth phase. The measurement of bubble load allows for this term to be calculated easily, rather than having to go through the laborious task of, for example, changing froth depths to determine this performance criterion (Contini et al., 1988; Vera et al., 1999b; Feteris et al., 1987)."

Jan 1, 2004

By David Lin

"Modal data from Red Dog Main Pit ores were collected and analysed on a size-by-size basis. The Main Pit data were compared to data from composite samples of Red Dog Aqqaluk ores. The data revealed that a large fraction of the sphalerite in the Aqqaluk baritic ore was tied up in sphalerite/galena binaries. This provided an explanation for its poor leadlzinc selectivity compared to Main Pit ores. The Aqqaluk vein ore exhibited levels of sphalerite/galena binaries comparable to that of Main Pit ores resulting in comparable lead/zinc selectivity.An attempt was made to correlate the modal and metallurgical data for Main Pit stockpiles. It was found that there was moderate correlation between the percentage of sphalerite locked in binaries with galena in the <C5>C6 size fi-action and sphalerite deportment to the leadconcentrate.INTRODUCTIONTeck Cominco’s Red Dog Mine in northern Alaska is one of the richest zinc districts in the world. Red Dog Mine has been in operation for over ten years and produces nearly 1 million tonnes of zinc concentrate per mum. Red Dog Mine is an open pit operation and current mining is conducted in the area known as the Main Pit. The Main Pit contains proven reserves of about 41 900 000 tonnes of ore grading 19.2% Zn and 5.2% Pb (Cominco 2000). To the north of the Main Pit is the Aqqaluk deposit. It contains probable reserves of 56 100 000 tonnes of ore grading 16.6% Zn and 4.1 % Pb. After the Main Pit has been exhausted, the Aqqaluk deposit will be exploited.The Aqqaluk deposit consists of three main geologic ore types: baritic, siliceous and vein. The siliceous ore type is dominant, representing 64% of the mineralisation. Composite samples of these ore types were created from drill core and batch flotation tests were performed on them. The flotation tests indicated that there were significant metallurgical differences between Main Pit ore and the Aqqaluk siliceous and baritic ore. The siliceous and baritic ores were found to suffer from poor lead/zinc selectivity (Lin 1999, G&T 1999). It was suspected that there were problems with the original Aqqaluk composite samples, thus a new set of composite samples were created and batch flotation tests were conducted again. In this set of tests, the new baritic ore still suffered from leadlzinc selectivity problems, but the new siliceous ore provided excellent metallurgical results. A summary of the flotation results is given in Table 1. Stockpile 132, which is typical of Main Pit ore, is given for comparison purposes. The mineral suite at Red Dog is relatively simple. The ore consists of galena, sphalerite and pyrite in a silicate matrix. The low zinc recoveries of the baritic ore were largely due to sphalerite losses to the lead concentrate."

Jan 1, 2002

By Jim Wickens, Andy Cole, John Pekrul

"The roaster facility at Barrick Goldstrike Mine treats double-refractory sulfidic/carbonaceous gold ore. Prior to oxidation in the roasters, the ore is ground in two parallel dry grinding circuits utilizing 19’ Ø x 75’ double rotator mills. The design plant throughput was 12,000 dstpd. However, process improvements have significantly increased throughput rates by 25-50%. The current daily throughput record is 20,078 dstpd. Grinding circuit improvements contributing to this success include feed size reduction, ball size optimization, automatic ball charging optimization, and operating strategy changes. In addition to the changes already made, this paper discusses future optimization initiatives including on-stream particle size analysis and “real-time” ore hardness determination techniques.INTRODUCTIONBarrick Goldstrike Mines is located 29 miles Northeast of Carlin, Nevada, USA. Through 2001, the property has produced over 23 million ounces of gold making it one of the premier gold operations in the world.Prior to Barrick’s ownership, the property began producing gold from a small heap leach operation in 1975. The small-scale heap leach production continued through 1986, and in January 1987, Barrick acquired the property. Increased exploration activity by Barrick significantly increased gold reserves. In August 1988, a 4,500 dstpd mill facility was commissioned to treat high grade oxide ore. Also, heap leach operations had significantly expanded. In 1990, the mill was expanded to 6,000 dstpd, and the first autoclave was commissioned to treat refractory sulfide ore. By the end of 1996, the mill and pressure oxidation facility had expanded to 16,000 dstpd and heap leaching had ceased as oxide reserves were exhausted. In 2000, a roaster facility was commissioned to treat double-refractory sulfidic/carbonaceous ore."

Jan 1, 2003

By J. A. Brothers, M. R. Foran

"AbstractThis paper reviews the progress made in the manufacture of hydraulic cement from iron blast-furnace slag by simply grinding the granulated material with other constituents. The influence of the chemical and mineralogical composition of the slag, the conditions of granulation, the manner of drying, and the fineness of grinding, on the hydraulic properties of the cement, is discussed. The effect of additions of lime, portland cement, and anhydrite, alone and in combination, on the physical and cementing qualities of the mortar and concrete made from Sydney blast furnace slag, is shown in tables of data and is reviewed in some de- tail. The work at the Nova Scotia Technical College has shown that a cement equivalent in every respect to portland cement can be made from basic blast furnace slag- by the us2 of certain quantities of portland cement as an activator.IntroductionBlast furnace slag is a potentially valuable material for the manufacture of hydraulic cement. It is a by-product of the manufacture of iron in the blast furnace, and is formed by the combination of the silica and alumina .of the iron ore with the limestone flux. The metallurgist terms a slag .acid or •basic according as the percentage of lime is less or greater than the percentage of silica plus alumina. The basic slags have the •more pronounced hydraulic properties."

Jan 1, 1950

By S. Banisi, J. Marois, A. R. Laplante

"This paper compares the behaviour of gold and ore in the grinding circuit of Hemlo Gold Ltd. Particular attention is given to grinding kinetics, classification behaviour, and liberation. For grinding kinetics, laboratory grinding of gold flakes and silica, 840-1200 um in size (14/20 mesh), was also performed to provide a standard for comparison and to study in a controlled environment the mechanisms of breakage, folding, smearing and impacting.Grinding kinetics were characterized at laboratory scale with breakage and selection functions. The breakage function showed that 75% of gold disappearing from the 840-1200 um class reported to the 600-840 um; this figure is much higher than for silica ( 46%) or most other minerals, and implies that comparatively fewer fine fragments are produced from the breakage of gold flakes, on account of gold's malleability. The selection function of silica was four times that of gold. At plant scale, the ratio of the selection function of ore and gold increased from 6 for at 50-100 um to 20 at 500-1000 um.Observation of original flakes and their fragments with the scanning electron microscope showed that the main mechanism of ""grinding"" from the 840-1200 um to the 600-840 um class was folding rather than actual breakage. This was confirmed by a measure of individual flake weight. The postulated breakage cycle is that relatively globular flakes become increasingly serrated through grinding; they can then regain their original shape through folding and reflattening into cylindrical and spherical shapes, as the majority does; however, some fragments will at this point undergo actual breakage. Photographic evidence is presented to support the proposed mechanisms.Smearing of gold unto silica was observed when silica was ground after a gold, and embedding of silica into gold flakes when gold was ground after a silica. Both mechanisms occur whenever gold and harder minerals are jointly ground, and result in ""unliberation"" of gold. It is postulated that smearing of gold onto other minerals plays an important role in explaining how gravity recovery can increase overall gold metallurgy, especially when used ahead of flotation.Classification of gold in the primary hydrocyclones takes place at a much finer cut-size than ore, 20 vs. 57 um. This and the slower grinding kinetics result in high gold circulating loads in the primary loop, 6700%, and a gold content in the primary cyclone underflow (PCUF) is twenty four times that of the ore. The gold size distribution for primary cyclone overflow is much finer than that of the ore, although they are essentially similar in the PCUF.Liberation, or more accurately ""gravity recoverability"", was assessed with a 7.5 cm (3"") Knelson concentrator. It varied between the thirties for the primary mill discharge and two cyclone overflows, to highs of 89 to 92% for the PCUF and secondary mill discharge, 89 and 92%, respectfully."

Jan 1, 1991

By Carlos F. Perucca, Maria Virginia Ramírez A.

"Chile based SQM S.A., exploits potassium chloride rich salts at the Salar de Atacama, in northern Chile. The process includes the solar evaporation of natural brines existing in the Salar salt bed, followed by conventional flotation to recover Muriate of Potash (MOP) for fertilizer use.This paper describes a structured method developed to aid in understanding the metallurgical response of the solar evaporated salts to conventional flotation. The method uses classical metallurgical data analysis combined with laboratory and plant-scale testing, and rudimentary mineralogical studies.As a result of the study, several changes were made to the flotation circuit which produced an operation that is much more consistent and easier to control, and has an increased recovery. An optimized circuit, currently being financially evaluated, has also been conceptually designed based on the findings of this work.INTRODUCTIONSQM S.A. is the world’s largest producer and distributor of specialty fertilizers, iodine, lithium, as well as a wide array of industrial and specialty chemicals. SQM is a public corporation whose shares are traded in the Santiago and the New York Stock Exchanges.SQM S.A. exploits the mineral rights at the Salar de Atacama in northern Chile. Its production processes involve the solar evaporation of natural brines existing in the Salar salt bed, aimed at the recovery of Potassium, Lithium and Boron compounds."

Jan 1, 2004

?? Intro ?? Mass blast principle ?? LaRonde evolution toward mass blast ?? Overview ?? Mining method ?? Longitudinal ?? LaRonde evolution (2002 to today) ?? Drill and blast design ?? Consumptions and statistics ?? Mucking strategies ?? Case study ?? Examples ?? Conclusion ?? As underground mines extends to greater depths, few questions must be asked: ?? How to: keep operations safe eep operation effective reduce the cost maintain and control the dilution ?? Geomechanic method and practices; significant advances have been observed in the field of: ?? ground support ?? mining sequencing ?? Drilling and blasting; research and development has been less extensive, probably due to the following characteristics: ?? Drill and blast are mainly production-oriented ?? Drilling and blasting are more oriented toward productivity ?? Technology relies heavily on suppliers ?? Highly stressed ground conditions ?? generally help the explosives to break the rock for fragmentation ?? intensify over-breaks or blast-induced

Feb 1, 2008

By M. N. Brodie

"The ability to adjust the speed of a SAG mill offers benefits to the process and to equipment maintenance. It can be provided with some slight effect on availability ranging from somewhat enhanced to somewhat reduced, depending on the particular equipment that is used. Several techniques have been developed for monitoring the magnitude of the contained charge, and several algorithms have been used to control mill feed rate and mill speed. The various benefits and the means by which they can be realized are examined and compared. Reasons for Variable SpeedProcess RequirementsThe recovery of minerals from ore is dependent on particle size and residence time in process. Separation in a given plant is most efficient at a particular rate and a particular size (e.g., 80% minus 200 mesh). If the particle size increases, less mineral will be liberated. If the particle size is significantly reduced, the process of choice may not be able to effect separation, and power, media, and maintenance costs would be increased.If a SAG mill-ball mill combination delivers the desired throughput at the correct size for efficient separation when processing ore of the design hardness, some adjustment must be made to maintain this condition when the ore changes. The processing of ore softer than design will result in overgrinding, unless:• the throughput is increased inversely to the change in hardness which lowers recovery by overloading the separation facilities;• or the SAG mill feed rate remains constant, but the speed is reduced to feed coarser material to the ball mill for finish grinding to the desired size.There is also the effect of changing milldiameter to consider. A nominal 36 ft diameter SAG mill will have an effective diameter of 35 ft with new liners and 35 ft 6 in. with worn liners. A mill designed to operate at 0.76 p.u. (per unit) of critical speed with new liners (9.84 rpm) will be changed to 0.765 p.u. with worn liners. If 0.76 p.u. is the desired value, the mill speed should be reduced to 9.77 rpm."

Jan 1, 2003

By T. R. Raponi

"The Williams Mine, Canada's largest gold mine, processes over 6,000 t/d of ore utilizing SAG/ball milling, leaching and CIP, carbon stripping, electrowinning and refining to produce gold dare bullion.Grinding accounts for over 50% of milling costs with grinding media, power and mill liners making up over 75% of grinding costs. Since 1991, several changes in these areas have been made which have significantly reduced costs, while fineness of grind and mill recovery have both been increased.This paper discusses the changes made in the grinding circuit over the past few years and assesses their impact on operating costs and mill operations.IntroductionThe Williams Mine is located in the Hemlo area of northwestern Ontario, about 40 km east of Marathon. It is operated by the Williams Operation Corporation, which is equally owned by Teck Corp. and Homestake Canada Inc. Canada's largest gold mine, the Williams Mine commenced operation in October 1985 at a rate of 3, 000 t/d. Mill throughputs have typically exceeded design, averaging 3, 397 t/d in 1986, and 3,380 t/d in 1987. In August 1988, production was increased to 6,000 t/d. Throughput averaged 4,212 t/d in 1988. Production increased over the next few years averaging 5,477 t/d in 1989, 6,248 t/d in 1990, 5,987 t/d in 1991, and 6,283 t/d in 1992. With a recovery of over 95.5%, production for the first three quarters in 1993 is averaging 6,408 t/d.GeologyThe main ore body is a steeply dipping conformable zone of microcline-quartz-muscovite rock. It occupies the contact zone between hanging wall metasedimentary rocks and foot wall felsic quartz feldspar porpyritic rocks of possible volcanic or subvolcanic intrusive origin. The ore body is enveloped by muscovite schists which are thickest on the footwall side. The schist is enriched with tourmaline, pyrite, and green mica containing vanadium and barium. The ore body contains pyrite and barite which occurs mostly in laminae and bands to veinlets and breccia fillings. The gold occurs as free (native) grains, 20 to 30 µm in size at grain junctions of the microcline and quartz. Visible gold is rare in the main zone. There are commonly two or more discernable layers of economic value which are separated by weakly gold mineralized material which usually consists of muscovite schist, barite rich zones or sulphide poor-microcline-quartz rock and in the upper and western fringes by biotite rich schist with feldspathic fragmental characteristics. Molybdenite is a common constituent as very fine disseminated grains in the microcline-quartz rock and is most prominent with gold enrichment. Stibnite and realgar are two of the more common accessory sulphides."

Jan 1, 1994

By D. S. Robertson

More than 700,000 feet of diamond drilling was completed in the Blind River area between 1953 and 1958. Much of this drilling was at depths which are still not usual in North America. However, as the tendency is to deeper holes, factual data from the Blind River operation may well provide information of value in future programs. Rates of drilling decreased with in-creasing depth, but uncommonly good rates (an average of over 50 feet per day over more than 4,000 feet of hole) were achieved with proper engineering and care. Costs varied as contractors and geologists became familiar with the area Hole deviation in the Blind River area was locally severe and control of the hole trace became a major problem. Careful surveying was necessary and found to be highly re-liable. It was found that control of the hole trace above 1,500 feet was much more difficult than at depths below 1,500 feet. This is explained by the mechanics of the drilling operation. Various methods of controlling hole deviation were attempted and,

Jan 1, 1962

By P. Wells

"In the past decade, there have been many developments in processing of nickel/copper sulfide ores. Improved pentlandite/pyrrhotite flotation selectivity with the use of new reagents, fine regrinding and Redox measurement (control) has led to increased pyrrhotite rejection and thus higher concentrate grades. Flash flotation has increased overall nickel and associated precious group metal recoveries. Recovery of both fine and coarse particles has been improved through an understanding of flotation cell hydrodynamics. The separation of copper from nickel in such ores has seen a similar level of development. From the late 80s to very recently, the use of flotation columns, the use of pyrrhotite depressing reagents and the improved understanding of the complex mineralogy of chalcopyrite, pentlandite and pyrrhotite have considerably increased copper / nickel separation efficiency. Copper concentrate with more than 30% copper and less than 0.5% nickel grade is now obtainable at 80-85% copper recovery from mill feed compared to 70-75% copper recovery with 30% copper and 1% nickel grade only a few years ago. Improved copper / nickel separation in milling operations has the potential to substantially improve the processing of the resulting concentrates and thus the overall return from the extraction of nickel and copper from sulfide ores.INTRODUCTIONNickel metal by itself or in alloys with other metals and materials makes a significant contribution to modern society. The relatively high price that nickel commands compared to other base metals is a reflection of the fact that, although abundant in the universe, nickel is sparingly distributed in the earth’s crust. There are two types of nickel deposits that are currently being exploited: complex sulfide ores and lateritic oxide ores. Lateritic contain no copper but in sulfide deposits, nickel– bearing minerals, principally pentlandite (Pn, [Ni,Fe]8S9), some millerite (NiS) and violarite ([Ni,Fe]S) are often found in association with copper-bearing minerals, mainly chalcopyrite (Cp, CuFeS2) and cubanite (CuFe2S3). The copper content of such ores can vary considerably from as high as 5-8% (in some Sudbury basin ores) to as low as 0.1% (in ores mined by Western Mining at Mount Keith, Western Australia and by Inco in Thompson, Manitoba). The valuable minerals Pn and Cp are almost invariably found associated with pyrrhotite (Po, Fe7S8) which along with nonsulphide rock has to be rejected to tails in the primary milling stage. The bulk concentrate from the primary stage is then treated to depress Pn and float Cp. A complete Cu/Ni separation at the mill would be highly desirable but this is not possible because of locking between a small fraction of the valuable minerals. As a result, Cu/Ni separation has to be carried out both during milling and during refining of the matte following smelting. At Inco, Jinchuan and in Norilsk, a chalcocite / heazlewoodite separation is made by flotation following slow cooling of the matte. In the present Sudbury Inco operations, Cu/Ni separation has not been conducted at the mill since 1991 and all Cu/Ni separation takes place at the matte processing plant. Because of the rising ratio of Cu to Ni in the ore, this strategy is under review and this paper describes some recent studies of circuits in preparation for possible installation of a copper / nickel separation circuit at Inco’s Clarabelle Mill in the Sudbury area."

Jan 1, 2004

By R. D. Brown

The Federal Government's White Paper on Tax Reform received further major criticism in the reports of the Committees of the House of Commons and the Senate, which recently completed a lengthy review including public hearings of the government's proposals. These reports both criticized the emphasis placed by the White Paper on its concept of tax equity rather than on a system which would promote economic growth. However, the Finance Committee of the House of Commons was prepared to accept, with modifications, a number of the White Paper's key reform proposals. The Senate Finance Committee was more critical of the basic thrust of the tax reform program and recommended that a modification of the existing tax system would be more appropriate to Canada's needs. Both Committees re-commended a more favourable treatment of mining income than that originally proposed in the White Paper, and to some extent both Committees suggested proposals that were even more favourable to the industry than those set out in Finance Minister Benson's amended proposals made in August of this year. This article out-lines the principal recommendations and comments in the reports of both the House of Commons Committee and the Senate Finance Committee.

Jan 1, 1971

By Gaby Steinbach

A novel synthesis is described for the preparation of supported gold catalysts for low-temperature CO oxidation. The novel route is a variation of the inverse co-precipitation method and requires amphoteric metal hydroxides, with zinc and aluminium hydroxides chosen. Catalysts were prepared by inverse co-precipitation (ICPa) and by the novel route (ICPb) and tested for CO oxidation at 60ºC. Preliminary results showed the novel route to be superior to ICPa; the catalysts prepared by ICPb showed higher catalytic activities. The effect on catalytic activity of parameters such as pH, calcination temperature, washing of precursor and calcined catalysts and ageing was investigated. A preparation pH of 9 and a Zn to Al mass ratio of 3 proved to be optimal. It was possible to remove residual chloride by washing thereby enhancing catalyst performance. Ageing and Mg citrate addition were also shown to improve catalyst performance. Characterization of the catalysts revealed that better activities were obtained when the support was more crystalline and had a higher surface area. The presence of carbonate-containing species in the support decreased catalytic activity. 197Au Mössbauer Spectroscopy revealed the presence of Au3+ when catalysts were heat-treated at temperatures of 200ºC and below. Catalysts calcined at 400º had 75% of the gold present as Au0, with the remaining gold present as Au3+.

Oct 1, 2003

By W. B. Boggs

The Noranda smelter was built by Noranda Mines, Limited, from the designs of A. E. Wheeler, consulting metallurgist, New York, for the reduction of ores and concentrates from the Horne mine, and to treat, on a custom basis, ores and concentrates from other mines in the Rouyn district. The smelter is situated at Noranda in western Quebec, about 330 miles directly north of Toronto. Ground was first broken for construction in November, 1925, before the completion of the branch railway into the district, which was not finished until October, 1926. After many difficulties and delays due to the Jack &apos;of transportation and the severe weather during the winter months, the smelter was started in December, 1927, and the first blister copper was poured on December 17th. The smelter was built throughout in two duplicate units, each with a rated capacity of 500 tons of ore per day. Operations were started with only one unit, and after several months it was found that one unit alone would smelt 1,000 tons of ore per day. At this time only one shaft, No. 3, existed, and its hoisting capacity and the capacity of the original crushing plant were insufficient to supply ore for two units at the increased tonnage. Accordingly No. 4 shaft was sunk and a new crushing plant provided to handle the ore hoisted there. This work was completed in the latter part of November, 1929, and since that time both smelter units have been operating.

Jan 1, 1930

By G. Papachristodoulou, O. Trass

"Performance data for both wet and dry grinding of materials have been obtained in this novel, planetary ring-roller mill over wide ranges or operating conditions. The Szego mill consists of a stationary cylindrical shell inside which grooved, radially mobile rollers rotate, driven by a central shaft. The mill has several internal design variables such as number, diameter and length of rollers as well as size, shape and pitch oi helical grooves. It is compact, has a high specific capacity, modest power consumption, and can grind many materials down to ultrafine powders. Illustrative data on product fineness and mill power consumption are given along with results from studies on grinding kinetics.INTRODUCTIONThe extensive use and importance of grinding as a unit operation, coupled with the rather low energy efficiency of conventional equipment provide a challenging incentive to investigate novel methods of comminution. Yet, most current development work is taking place in mill performance modelling and optimization, or with various detailed improvements rather than in the field of new equipment development.This paper is a report on the development of a ring-roller mill invented by the late L.L. Szego which embodies several novel concepts. The mill has a broad range of applications, may be operated wet or dry, and can grind materials down to ultrafine sizes with modest energy consumption. It has been developed by General Comminution Inc. in close cooperation with the University of Toronto."

Jan 1, 1986

DynoMiner APS Delivery Systems Overview ? New Design of DynoMiner APS-M2 ? Stand alone or attach to Cargo type 10,000 lb (4536 kg) emulsion bins. ? Hose reel w/200-ft (61-m) by 1-inch I.D (25-mm) hose capacity, power rewind. ? Increased water and trace capacity. ? Hose reel and gassing offered as options. ? New Flow Meter ? DN-100: aluminum body, UHMWPE rotors. ? Will be offered as an option. ? APS Nomenclature ? Proposed changes ? DynoMiner APS and APS-M1 to become DynoMiner APS Drifter ? DynoMiner APS-M2 to become DynoMiner APS Stoper. ? Both to have optional gassing / flow metering.

May 1, 2004

By Paul Laframboise, Nigel MacDonald, Mike Hallewell, Robert Thorpe

"Galmoy Mine, owned by Arcon Mines Limited, has operated since 1997, and is one of three operating lead/zinc mines in Ireland. Changes in ore type starting in mid 2002 created challenges to metallurgical operations at Galmoy. This resulted in unacceptable lead and zinc flotation performance, which prompted initiation of a formal plant review and a subsequent stabilization programme. This involved a structured review of operational practices, development of a new Standard Operating Procedure (SOP) which in turn led to significant changes in process control equipment needs in conjunction with extension of zinc flotation cell residence time.This paper will describe the metallurgy of the Galmoy operation. Reasons for the poor metallurgy experienced in 2002 will be described, as well as the solutions identified to overcome these problems. By the second quarter of 2003, these solutions had been implemented and recoveries had risen to record levels.INTRODUCTIONGeneralGalmoy Concentrator is located in County Kilkenny (Refer to Figure 1 below) and was constructed during 1996 and commissioned in 1997.The concentrator at Galmoy had been designed initially to treat 650,000 tonnes per annum of primarily CW ore type. The main mineral of economic significance was sphalerite (Typically 10 to 11% Zn) with some minor galena (0.7%Pb) in a dolomite (Magnesium Carbonate) host rock.The only other competing sulphide mineral was pyrite (Circa 3 to 5% Fe in Mill Feed. This CW ore type predominated the first 6 years of production, but in August 2002, the ore mineralogy changed due to significantly higher levels of pyrite rich G ore body being blended in with CW ore."

Jan 1, 2005

By Ron Board

"Probably the only thing that can he said about conveyor belt scales without fear of contradiction is that they have been responsible for as much or more puzzlement, argument and frustration than almost any other piece of equipment commonly found in ore processing facilities. To be sure, there are certainly a good number of satisfactory installations, some of these having been achieved through forethought and careful consideration in the early stages of plant design, while others seem to owl their success to what seems to be little more than good luck or white witchcraft; and it might also appear that black witchcraft or other gremlins are solely responsible for the poor performance of many belt scales that enjoy well-designed installations with apparently good operating conditions.This paper is intended to acquaint users with the major operational reasons why belt scales seem so fickle (and downright ornery too), and establish some reasonably simple test standards against which the performance of scale hardware can be measured. Then it shall be shown how the design flexibility of electronic scale systems can offer particular advantages in overcoming some of these everyday problems in a practical way, and without undue inconvenience to plant operations."

Jan 1, 1975

By Éric Poulin, Simon Gariépy, Mario Paredes Malca

"While the design of a control strategy depends on the available process knowledge, its implementation depends on the available process information. On-line chemical analyzers are today widely spread in the mineral processing industry. A real-time concentration measurement of chemical components is valuable information that could bring control strategies to whole new levels. However, the use of these measures rarely reaches anything more than process monitoring. The reason is simple: the on-line chemical measurements quality is most of the time insufficient to be directly included in control strategies. The choice is then made to let the critical eye of the engineer or the operator appreciates the measurements before making any decision based on it.Data reconciliation through mass balance is a technique today widely used in the mineral processing industry to increase the accuracy and the reliability of plant data, mainly for accounting and survey analysis purposes. Real-time data reconciliation of on-line measurements appears as a natural coupling of technologies that could bring new process optimization trends. Once overcome the technical difficulties, full valorization of the instrumentation investment could be reached.This paper presents the application of real-time data reconciliation for process control and performance monitoring. It proposes a general approach, discusses challenges and illustrates concepts with industry experiences."

Jan 1, 2006

By Mike Robotham

When RFQ?s are received they often contain detailed technical specifications which suggest a departure from the suppliers own customary approach to the design. Both client and end user are quite rightly influenced by their own experiences. The question is who is right, the client and his consultant, the supplier or perhaps a combination of these. This paper looks at some of the fundamental variances that often occur in the approach to the mechanical design of drum hoists, based on our experiences of recent years. Director of Engineering, Mike Robotham is a chartered engineer and has been with DavyMarkham for over 30 years. Having completed a craft apprenticeship he later joined the engineering department as a junior engineer. He has a wealth of experience of working on medium to large engineering projects in the field of mechanical, electrical and hydraulic equipment

May 1, 2011