Search Documents

A synthetic gold-silver telluride material (mainly sylvanite) has been prepared and its physical and chemical properties checked. Flotation tests using a Hallimond tube were conducted using commercial xanthate collectors. At collector concentrations of 10-3M with the addition of 5 × 10-4 M CUS04, no obvious differences in the mineral recoveries were seen irrespective of whether amyl, secbutyl, isobutyl or isopropyl xanthates were used. However, when the concentration of xanthate was reduced to 10-4 M or in the absence of the copper sulphate activator, the effectiveness of the collectors was in the order: amyl > secbutyl > isobutyl > isopropyl > ethyl. Changes in the slurry pH appeared to have little effect on the recovery of the telluride mineral.Leaching tests of the precious metal telluride showed that both gold and silver dissolve in alkaline oxygenated cyanide solutions but at a much lower dissolution rate than metallic gold or silver. Both leaching tests and electrochemical measurements indicate that the dissolution rate of gold-silver telluride is controlled by the pH and cyanide concentration of the leachant.Roasting the gold-silver telluride materials in air at temperatures between 550 and 750°C resulted in its decomposition into a metallic gold-silver alloy and tellurium dioxide.

Jan 1, 1994

Blasting in Norwegian mines is often carried out by contractors who tend to look for the cheapest solution, without concern about fragment quality. The requirementsfor a contractor are usually only related to the maximum size of boulders and the quantity per month. Even when the owners of the mine are responsible for blasting, very little effort is made to optimise the blasting process. This paper presents test methods which were used and results from small-scale and full-scale blasting tests. In the small-scale tests, cubes 500 x 500 x 500 mm of four different rock types were blasted in a chamber, using two types of dynamite explosive. The velocity of detonation (VOD) for the dynamite explosives was 3000 m/s and 6000 m/s respectively. Three cubes of each rock type were blasted with each type of explosive, and a total of six cubes of each rock type was used. The entire muckpile (approximately 350 kg) was- sieved and weighed after each blast and fragments between 8-16 mm were tested for impact values and flakiness. The results of these tests clearly showed improvement in fragmentation the closer the acoustic impedance ratio of the explosive (VOD x density) over the rock (Cp density) was equal to one. The results also showed that the quality of the fragments (in terms of impact values) tends to be better when the cubes are blasted with the high velocity dynamite.

Jan 1, 1995

The stratigraphic sequence west of Mount Isa contains the Judenan Beds, Eastern Creek Volcanics, and May Downs gneiss. It is an incomplete sequence as major north-south faults divide the area into four separatezones containing portions of these different units. The first three zones, which occur directly to the west of the Mount Isa Fault, consist of quartzites and quartz-mica schists which are uncorrelatable between zones but have been grouped together as the Judenan Beds. The most western zone contains an incomplete section of Eastern Creek Volcanics which rests conformably on a unit believed to be equivalent to the Mount Guide Quartzite; this is again underlain by the May Downs gneiss. A detailed description of the rock types is presented, but only a broad stratigraphic correlation is possible with the very much thicker sequence to the east of Mount Isa.The age of sedimentation is believed to be Lower Proterozoic and it may not occur in the type of geosynclinal basin envisaged by previous authors.This sequence is intruded by many small basic intrusions and also the Sybella Granite with its associated microgranite and pegmatites. The Sybella Granite consists of both a massive and a foliated phase; the latteris generally restricted to the margin of the main granite mass.Four regional metamorphic zones have been identified on the basis of their pelitic mineral assemblages; these are a chlorite, biotite, biotite-cordierite, and a sillimanite zone; separating each are prominent north-south faults.This metamorphism is a regional metamorphism which accompanies the first generation folding of the area and is not associated with the emplacement of the Sybella Granite. A very localized retrogressive metamorphism is also found in some areas of second generation folding.

Jan 1, 1972

By P Bonniwell

As a part of the Newcrest, Telfer Expansion Project, a consortium of Australian, Canadian and South African Mining Contractors in joint venture have been contracted to develop the hoisting shaft. The parties namely; Byrnecut Mining Pty Ltd, Murray and Roberts RUC and Thyssen Mining Construction of Canada Ltd have combined their individual expertise to excavate the shaft. There is a particular emphasis on the use of proven shaft sinking techniques from North America and in particular integrating electric hydraulic drilling equipment and personnel from the Canadian Mining industry. The Telfer hoist shaft when completed will have a finished diameter of 7.1 metres and extend to a depth of 1170 metres below the collar. The shaft will be fully concrete lined and will later be equipped for hoisting ore from the Telfer deeps at a rate of five million tonnes per annum. The shaft when completed will be the largest shaft ever completed in Australia on a volumetric basis. This paper will examine the technical aspects of the shaft sink, as well as exploring the integration of personnel and equipment from the frozen prairies of Saskatchewan, Canada into an operation in the Great Sandy Desert of Western Australia. What are the spin-off benefits for the development of other shafts within Australia?

Jan 1, 2005

By Moore A. J

Blasting in mines in an urban environment can be conducted safely and within regulatory vibration limits by careful attention to detail and the application of correct techniques. Factors affecting blast vibration are described using surface and underground mining examples. An understanding of these factors provides an essential base for effective planning and operational control. Techniques are described for assessing and predicting vibration levels and the presentation of data for planning purposes such as environmental impact statements for new projects and the protection of buffer zones around existing operations.

Jan 1, 1997

Interpreted geologic domains provide the geologic architecture of many current models used to estimate the potential economic resources in mineral deposits. The spatial extent of each domain is usually defined by a three-dimensional wireframe or triangulated surface.The set of geologic wireframes forming part of a resource model might generally be called a spatial interpretation of some set of geologic features coincident with the mineralisation, based primarily on logged and mapped properties of the samples and other exposures of the mineralisation. The interpreted spatial distribution of rock type, alteration and grade of drill hole samples above a particular grade threshold are commonly used criteria in constructing the geologic domain wireframes. Frequently, the grade threshold is closely related to the anticipated economic cut-off grade. The boundaries or spatial limits of different domains are most commonly defined as æhardÆ or æsoftÆ. A æhardÆ boundary usually means no dependent relationship of any kind is defined between the properties of samples inside a particular domain wireframe and those samples outside the wireframe. A æsoftÆ boundary commonly implies that some kind of dependent relationship does prevail between the properties of samples inside and outside the particular wireframe. Many ways are used to describe those relationships, few of which are based on spatial analysis of the continuity of sample attributes across the domain boundaries. In local estimation procedures such as ordinary block kriging, æhardÆ boundaries act as a total barrier to the influence of samples on either side of the boundary depending on the location of the block being estimated. In some instances, æsemi-permeableÆ boundaries are used in which the samples inside a domain wireframe are allowed to influence the estimates outside but not the reverse. This can lead to many undesirable effects in estimates of block grades.This paper discusses the value of this approach to geologic domaining from a viewpoint of model complexity, as well as in relation to the implications for both linear and non-linear estimation methods and contrasts it with alternatives. It also explores some important consequences of using æhardÆ and æsoftÆ geological boundaries with the commonly used modelling methods: excessive smoothing of estimates near domain boundaries and conditionally biased estimates of grade at the global and local scale.

Sep 26, 2011

By Andrews JRG

Chrysotile asbestos is a valuable resource. Used as a reinforcement in asbestos cement, products are obtained which are cheap, are not attacked by vermin, do not rot or support growth of fungi and are unaffected by water or humid conditions. Such products are of great value in the developing countries where inexpensive and durable building materials and pressure pipe are very important to development, housing and water supplies. Concern over the adverse effects of inhaling asbestos has led to the introduction of increasingly stringent controls world wide on the quantities of airborne asbestos per- missible in the occupational situation. Wet processing has the potential for virtually eliminating the environmental concerns with asbestos dust both in fibre production and in the materials handling section of the manufac- ture of asbestos cement products. In addition, high efficiencies associated with wet process- ing mean that better yields are obtained and that the tailings which are dumped have a lower residual asbestos content. Since early 1977, ICI Australia and Woodsreef Mines have been engaged in a programme of research to develop and evaluate a wet mill- ingprocess to produce, from ore and existing tailings, high grade fibre suitable for use in asbestos cement products. The process has been developed through microscopic studies, labora- tory bench scale experiments, work in a small scale semi-continuous plant and product evalua- tion on experimental size Hatschek asbestos cement machines. A prototype mill with a normal feed rate of 1z tonnes per hour and capable of producing pipe grade asbestos from Woodsreef ore has been constructed and was operational from January, 1982 to July, 1983. A range of asbestos cement products have been made successfully on full scale Hatschek machines using fibre from ore and tailings milled in the prototype mill. Economic evaluations indicate that a wet process mill would be cheaper to build, operate and maintain than an equivalent dry process plant. A commercial plant has been designed 1. Manager New Process Development, Woodsreef Mines Limited, Barraba, Australia. 2. Senior Lecturer, Department of Chemical Engineering, Monash University, Vic, Australia. formerly Senior Research Officer, Research Department, ICI Australia Limited

Jan 1, 1986

Rifting and transfer faulting in the Late Cretaceous to Early Tertiary resulted in the formation of the Bundaberg Trough and Wallaville Basin and deflected the margin of the Maryborough Basin southwestward between the Kolan and Burnett Rivers. During the Cainozoic, three periods of volcanic activity occurred in the Bundaberg-Gin Gin area. The oldest of these periods, Paleocene to Early Eocene, resulted in the outpouring of tholeiitic lavas. During the Late Miocene to Pliocene, undersaturated alkali basalts generated at depths of from ca. 35 to 55 km were emplaced. These lavas were followed in the Pleistocene by the alkaline Hummock and Berrembea Basalts. The loci of eruption of all of these lavas were controlled by the intersection of the transfer fault system and pre-existing north to northwesterly trending faults in the Bundaberg-Gin Gin area.

Jan 1, 1990

By Firmin K

The Mt. Tom Price orebody of Hamersley Iron Pty. Limited consists of a folded hematite - shale sequence capped by a layer of goethite. Consequently, variations in iron content occur within the orebody, and as the overall grade is below that required to make specification products, selective mining must be carried out. A necessary preliminary to quality control'of products based on selective mining is the production of advance data, on the tonnages and grades of material to be expected in future mining areas. Bench plans showing zones of different grades and types of material anticipated are prepared from structural geological information. The grades of materials on a bench are essentially governed by the positions and attitudes of the shale bands. Quality control is exercised by blending different grades and types of material in primary crusher feed. Iron grade is the prime grade consideration although sometimes the level of phosphorus content must be considered. Pre-production grades Are determined from assay of samples taken from blasthole cuttings.

Jan 1, 1980

Acupan is considered to be an intrusive centre as several igneous phases have been emplaced in the vicinity of the mine over the past 8 Ma. They include the Lucbuban gabbro, Virac granodiorite, Ampucao dacite porphyry (ADP), Hartwell plug, Itogon plug and the multi-phase Balatoc diatreme. These intrusives have high-K calc-alkaline affinities and are grouped together as the Virac Complex.Porphyry-style mineralisation formed during the final crystallization of the ADP in the late Pliocene, with the deposition of two vein stages from high-temperature hypersaline magmatic-hydrothermal fluids. K-silicate alteration halos surround the first stage of veinlets (stage I); they are surrounded in turn by a propylitic assemblage. White sericite and/or intense propylitic halos envelop the second stage of veinlets (stage II) and grade into a weak nrnnvlitir accPmht o

Jan 1, 1990

In the past ten years or so there has been a renewed interest worldwide in the processing of refractory gold ores. The Archean province of Western Australia contains both numerous and major gold deposits, and has a long history in the development and practise of treating refractory ores (eg Blaskett and Woodcock, 1953). Depletion of shallow oxidised ores in recent years has re-focused attention on deeper sulphidic ores, and as a consequence has renewed interest in treatment methods for those ores which are refractory. Mineralogical factors he at the heart of reasons as to why these ores are refractory, and are the key to designing and improving treatment options in the longer term. This paper presents an overview of mineralogical factors that are relevant to the processing of refractory gold ores in the Archean of Western Australia. It is based on a number of research projects and other work on a variety of gold deposits, mainly in the Eastern Goldfields region, carried out over the past five years or so.

Jan 1, 1991

By Hilde TWC

Synthesis of GLORIA side-scan sonar and other geophysical data has provided morpholo- gical and tectonic details of the interaction between the Nazca and South American plates along the Peru Trench (80S-15¦S). Our analyses suggest that a new propagating rift of the Galapagos type is evolving along the Mendana Fracture Zone (MFZ). Subduction induced rift- ing of the Nazca plate is accompanied by organized seafloor spreading for the last 3 Ma at least. GLORIA sonographs and bathymetric mapping show an 8-10¦ divergence in MFZ width towards the Peru Trench. The fracture zone comprises numerous ridges and troughs and a lack of sediment cover in the axial part. Young magnetic lineations (anomalies 1-2A) are observed within the fracture zone wni.cn are orthogonal to the older Nazca plate lineations. The central anomaly narrows west- ward and can be observed up to 400 km seaward of the trench whereas anomaly 2A is terminated about 200 km from the trench axis. Recent SeaMARC II sonar mapping in the region shows large igneous blocks in the Trench axis to the north of MFZ but absent to the south. We believe these blocks represent young seafloor of MFZ rift/spreading center broken off from the ridges as they subduct along the Peru Trench. The MFZ rift is propagating west- ward at a rate of 115 km/Ma (25 km/Ma relative to the South American plate). Given the present rates of accretion at the East Pacific Rise and of propagation along MFZ rift, the Nazca plate will be divided into two parts in about 35 Ma.

Jan 1, 1987

The Olympic Dam copper-uranium-gold-silver deposit, located approximately 520 km north-northwest of Adelaide, South Australia (Figure 1) was discovered in 1975 by Western Mining Corporation. A joint venture to facilitate development of the deposit was formed in mid-1979 between WMC (51 per cent) and the British Petroleum Group (BP, 49 per cent). Production commenced in 1988, and current annual output from the mining and treatment of 2.2 Mt of ore is approximately 65 000 t of refined copper and 1400 t of uranium oxide. Significant amounts of refined gold and silver are also produced.

Jan 1, 1993

By Susanto A

As part of the current NERDDC funded project studying Dragline/Hopper/ Crusher/Conveyor systems for overburden removal, an investigation was carried out to assess the feasibility of automating the swing-to-dump phase of the dragline digging cycle in order to main- tain consistent performance of spotting the bucket above the hopper prior to dumping. The study involved design of automatic position controls for the hoist, drag and swing drives and simulation of detailed mathe- matical models of the three electromechanical systems and their associated electrical control schemes. The design of the hoist and drag systems to position the bucket in the boom plane is relatively straightforward. Simulation results show fast and accurate performance, with no evidence of interaction between the two drive systems through the ropes. The design of the swing position control system involves special strate- gies to cater for variable inertia and to damp the pendulum oscillations of the bucket. The use of a bucket pendulum model and variable dynamic compensation embedded within the feedback control loop, along with optimal speed/angle slowdown trajectories, has yielded fast and damped positioning responses under simulation.

Jan 1, 1989

By Schoning W. L

Ore deposit models form the basis for numerous other economic decisions in the mining process. The success of these economic decisions therefore depend directly on the accuracy of the ore evaluation process. The Geology Department at the Sishen Iron Ore Mine is responsible for the generation of a reliable geological computer model of the rock material with predicted grades. This information is then utilised for further ore reserve calculations, mine planning, production scheduling and grade control. Owing to a very complex geological orebody, grades and beneficiation characteristics differ significantly from sample to sample. This means that ore evaluation is a difficult process and great reliance is placed on computer techniques. In 1993, preparation for the ISO 9002 quality certification of the mine motivated the Geology Department to hold formal `problem solving' sessions in order to identify and revise problem areas in operating

Jan 1, 1995

By Thomas MJ

The Cannington silver-lead-zinc deposit is located at latitude 21¦ 52' 9" South, longitude 140¦ 55' 10"" East, on the south-eastern margin of the Proterozoic Mount Isa Block (Figure 1), 135 kilometres south-east of Cloncurry. Access is via a graded shire road for 80 kilometres south from the small pastoral community of McKinlay.REGIONALThe deposit is hosted by the Proterozoic Soldiers Cap Group within the Mount Isa Block Eastern Succession. South of the Cloncurry Beardsmore et al (1988) have grouped part of the Eastern Succession stratigraphy intothe Fullarton River and Soldiers Cap groups (1760-1740 million years) which together make up the Maronan Super Group. This is an apparently conformable sequence 10 kilometres thick and consists of metamorphosed sediments and volcanics with intrusive amphibolite bodies.The Maronan Super Group has experienced a complex history of deformation with up to six events having been recognized. The stratigraphy trends broadly north-south and is predominantly characterized by tight, upright isoclinal fold structures.

Jan 1, 1993

This paper reviews the various processes successfully in operation to treat refractory gold ores and describes in detail the alkaline pressure oxidation circuit operating at the Barrick Mercur Mine, Utah, U.S.A., on car- bonaceous/sulphide refractory ore and the acidic pressure oxidation circuit operating at the Barrick Goldstrike Mine, near Carlin, Nevada, U.S.A., on sulphide refractory ore. The autoclave process is important to Barrick for the extraction of gold. The Company has operated successfully a 750 ton per day unit at its Mercur property for the past two years and more recently has commissioned a 1500 ton per day unit at Goldstrike. The paper presents data relative to operating costs, materials of construc- tion for autoclaves and peripheral equipment, reagent requirements, and changes required during commissioning for both autoclave systems.

Jan 1, 1991

When Matthew Flinders entered in his log `This land forms the South side of the large bight; and besides projecting beyond the coast line, and being a little higher than usual is remarkable for having some reddish cliffs in it, and deep water near the shore', he was commenting on the deposit of bauxite at a place now known as Weipa. This sighting took place on 9 November 1802, and probably represents the first direct entry in Australia acknowledging a potential mineral deposit. Flinders, of course, had no idea as to what he was looking at, nor did he land to determine its content. If he had, he probably would have had no idea of the substance, and even less knowledge of its use. Nothing further was done to this for about 150 years.

Jan 1, 1993

By Gonzalez JM

The Pao gold prospect in N. Luzon, is an example of a high sulphidation epithermal gold system hosted in Mid-Tertiary alkaline volcanics, in the Philippine Arc. Styles of mineralization include: quartz-enargite veins, vuggy silica alteration bodies, and pervasive low grade (0.5ppm) gold mineralization, associated with kaolinite-pyrite-quartz alteration, and geochemically characterized by high As and Hg. Early magnetite-epidote-chlorite alteration linked to an unexposed granitoid is overprinted by an extensive zone of advanced argillic alteration (kaolinite-pyrite-quartz). No alunite is recorded. Important controls of mineralization include; a broad anticline intersected by axial faults, permeable pyroclastic units, and upward confinement of the alteration system by a highly impermeable, clay-rich volcanic unit. At this stratigraphic position the most important mineralization waz developed. The Pao high sulphidation system is not closely related to a stratovolcanic centre, and has formed subsequent to deformation of the volcanic field. It may, however, be related to an unexposed comagmatic intrusion.

Jan 1, 1990

By Ault A. R

The recent modernisation program at the Risdon electrolytic zinc smelter of Pasminco Metals - EZ (PMEZ) inyolved significant changes to the composition of cell electrolytes. The most significant were increased acidity and sulphate level, a reduction in Co level, and the replacement of 2-naphthol in the additive mixture with licorice. In determining acceptable operating ranges, a relatively large number of industrial deposition tests under controlled conditions was required. The cathode zinc deposits so produced were examined in terms of overall appearance, crystal structure according to X-ray diffraction, and a micro-roughness parameter. Beginning with typical deposits produced in the presence of an excess of one of the addition agents glue or antimony or a mist suppressant (licorice or 2-naphthol), a simple classification system was developed. In this system, the deposits are divided into the following types: Doughy, Pinholed, Compact and Stressed. There was a weak correlation between deposit type and crystal orientation. In terms of ease of stripping, observations in plant operations showed that only Compact and Pinholed were consistently acceptable. Current efficiency was normally maximised by producing a Compact deposit. Process variables such as zinc concentration, temperature and the use of strontium carbonate were found to cause changes in deposit type if the reagent mixture used was unchanged. From the knowledge gained, guidelines were developed to allow glue and antimony additions to be altered to fit new circumstances. The simple classification system was first used to expedite recovery from undesirable morphologies and then to optimise individual cell units operated under substantially different conditions. It is believed that finer control could be exercised by determining the micro-roughness of Compact deposits. However, difficulties can arise if sudden, large deviations occur and go undetected. Suggestions are given for an improved additive control system. The classification system developed has been compared with published information in the literature, and good correspondence was noted suggesting a predictable relationship between short-term, laboratory deposition tests and observable phenomena in industrial electrowinning cells run under steady conditions.

Jan 1, 1993