Search Documents

By Wakamatsu DT, Nakahiro Y

This present paper deals with the fundamental study of the separation of fine cassiterite and quartz by liquid-liquid extraction using iso-octane as an oil phase, dodecylamine acetate (DAA) as a collector, and sodium chloride as a depressant. With regard to the distribution of fine cassiterite and quartz between oil and aqueous phases, the effect of DAA has been investigated in terms of pH, DAA and NaCl concentrations, zeta potential, and adsorption density. From the results of the experimental work, a maximum recovery of cassiterite in the oil phase was obtained with pH around 6.0, DAA concentration of 1.0 x 10-5 mole/litre, and NaCl addition of 0.1 mole/litre. In these conditions of liquid-liquid extraction, most of the fine quartz remained in the aqueous phase. Thus it was found that NaCI was an effective depressant for fine quartz under optimum conditions. A series of separation tests by liquid-liquid extraction was then conducted for the mixed samples (6.0 per cent Sn) of cassiterite and quartz. By a single separating process, the per cent of recovery of cassiterite in the oil phase was about 92 per cent with a grade of 27 per cent Sn. The same results could also be obtained by using kerosene in place of iso-octane as the oil phase.

Jan 1, 1993

By P Gardner

The Kanowna Belle gold mine in Western Australia has reached a depth of 1000 m on the way to 1300 m. A feasibility study undertaken in 2006 identified the mining of E-Block as both technically and commercially feasible. One of the major risks identified in the study was the ventilation capacity, as the existing primary ventilation system would not support the production schedule for mining and a major system upgrade would be required. Failure to provide the necessary airflow would put the project at risk. A review of the airflow requirements and infrastructure options detailed in the feasibility study was undertaken to ensure that the assumptions and design were optimised. This review recommended a minimum airflow of 206 m3/s, but by acknowledging the necessary constraints imposed by mining at depth and re-engineering the mine layout to optimise the primary ventilation circuit, this requirement was reduced to 160 m3/s. This represents a 22 per cent reduction in airflow and a reduction in capital cost that will see mining at depth become economically feasible at Kanowna Belle. This paper discusses the processes that led to a redesign of the mining layout and highlights the importance of including the ventilation network in the optimisation process.

Jan 1, 2008

The Cleveland Mine has an annual ore production of 400,000 tonnes at a grade of 0.79 per cent tin and 0.30 per cent copper. It is achieved by an open stoping method, mechanised overhead sub-level benching. The operation is trackless with a ramp access from all working places to the surf- ace. Broken material is loaded from the stope and development headings into diesel trucks and hauled to the surface crushing plant.

Jan 1, 1977

By I P. W Chau

Construction of twin stacked railway tunnels through mixed ground conditions in the heavily populated urban environment of Hong Kong, including tunnelling in poor ground conditions, with low cover and under or adjacent to sensitive structures with minimal impact was the challenge presented by the tunnelling section of the Kowloon Southern Link project. This paper details how twin 1.1 km tunnels of 7.0 m internal diameter were driven by Mixshield tunnel boring machine (TBM) in mixed ground through one of the exclusive shopping and hotel districts in Kowloon. The paper addresses the challenges required to be considered and managed for the success of the project, including ground conditions, TBM selection, Mixshield TBM operation, settlement monitoring and control, ground- borne noise and vibration, proximity to utilities, buildings, roads and operating railways.

Jan 1, 2008

By J Szymanski, Y Hu

Excavation engineering involves complex processes for primary and secondary extraction of materials. The shovel excavators bear varying mechanical energy input and stress loading across the working bench during excavation. These varying mechanical energy input and stress loading effects cause significant wear and tear and fatigue failure in equipment components. These effects further result in unplanned downtimes, reduced efficiency and high production costs. In addition, the mechanical and electrical control systems must be operated in efficient profiles to generate maximum outputs and efficiency from these excavators. Efficient technologies are therefore required to solve these problems in order to reduce production costs and increase efficiency. In this paper, the authors develop a rigorous simulator for a hydraulic shovel in a surface mining environment. The finite element model is used to capture the stress profile within the shovel components during excavation, such as, the bucket, stick and boom assemblies. The profiles are classified into normal, critical and extreme ranges, with appropriate corrective measures to avoid extreme loading conditions. The loading capability of shovel excavators can be examined by assessing its structural strength against all possible maximum loads working on the equipment. The dynamic model is used to define efficient profiles of the critical structural components of hydraulic shovels during digging operation. This assessment is used to locate the maximum possible loads and the critical sections of the structures. The method presented in this paper forms the basis for developing comprehensive simulator models for efficient shovel operations in constrained mining environments.

Jan 1, 2003

By Duke J. H

Advanced computer aided geological modelling techniques are now available to the geologist to allow the rapid evaluation of a gold orebody at various stages of its development. The types of grade estimation techniques used change during the various stages as the density of drilling and knowledge of the deposit increases. At the prospect evaluation stage drillhole intercept selection techniques are coupled with preliminary 2D (vein or layer) modelling or 3D block modelling techniques to arrive at a geological resource estimate. At the prefeasibility and feasibility stages more sophisticated 2D and 3D modelling techniques, such as domain controlled grade interpolation with anisotropy, are used along with interactive open pit and underground mine design, to calculate recoverable reserves. At the production stage closely spaced blasthole sample data is modelled quickly and coupled with interactive grade control facilities. Shot volumes, tonnages and grade estimates can be databased to provide reconciliation figures. These modelling techniques are embodied in MINEX-3D, an Australian software system which, with the emergence of the 386-based PC and high resolution (VGA or better) graphics, makes a whole range of advanced geological modelling techniques available to most exploration and mine geologists.

Jan 1, 1989

By B, J Bianchini, N Voermann, C Crowe

Operational and economic imperatives in the metallurgical industry have led to numerous advancements in furnace design. Modern furnaces provide high production rates, high percentage online time, long campaign life between rebuilds and safe operating conditions. Current trends for maximising plant efficiency include increasing the throughput of existing process vessels (often by a factor of two or more) and the use of newer, highly intense processes. In both instances, the process intensity results in the generation of higher heat fluxes to the crucible walls. High-intensity furnace operation with the objectives mentioned above has become possible with the following furnace design features: Strong sidewall cooling systems, using copper coolers, to accommodate the high heat fluxes encountered while protecting the crucible refractories; Robust, spring-loaded furnace horizontal and vertical binding systems which maintain tight brick joints through-out all stages of operation; and Well-designed, intensely cooled tapholes for metal, matte and slag. The integration of these features along with properly selected refractories, appropriate instrumentation systems and efficient water-cooling systems is also highly critical. These design features have been successfully implemented in electric smelting furnaces, flash smelting and converting furnaces (Outokumpu and INCO types) and lance injection furnaces (Mitsubishi, Ausmelt and Isasmelt types). This paper will discuss design aspects and operating results for several installations.

Jan 1, 2002

The application of single liquid cement for fracture grouting in base rock may have history more than 120 years. The disadvantage of it is difficult to increase the grouting efficiency, because the jelling time of it is very long and hard to control. The double liquid grout, such as chemical grouts and cement water glass grout was developed at the end of 1960.'s Although the jelling time of this kind of grout can be controlled, it mast adopt double liquid grouting technology, use complicated equipment and is not easy to control component's ratio of the grout. Another disadvantage for chemical grout is high price, and have pollution to environment. OCE series single liquid grout is the effective grout material developed recently by making large efforts in Ohina. Main feature of it is that the jelling time is easy to control, materials from cement and clay are very cheap and without pollution to environment, and the grout can be injected by single liquid technology. The effect of QCE series grout has been proven by its application in China. It can be believed that QCE grout has great economic efficiency and will give a push to develop grout material.

Jan 1, 1988

By H Han, X Wang, T Li, D Duan

"In this paper, the reduction and separation behaviour of iron and slag in carbon composite iron ore pellets has been investigated experimentally using an electric resistance furnace simulating a rotary hearth furnace process. The factors that affect the formation of iron nuggets, such as temperature, holding time, molecular ratio of C/O and basicity, are discussed. Results show that the reduction of iron ore, carburisation of reduced iron and the composition and quantity of slag are very important for producing iron nuggets. Through optimisation of process parameters, iron nuggets can be formed below 1300¦C when holding time is 20 minutes, C/O is 0.7 and basicity less than 0.5. This study provides a theoretical and technical basis for iron nugget production.CITATION:Duan, D, Han, H, Wang, X and Li, T, 2013. Iron nugget production technology in rotary hearth furnace process at lower temperature, in Proceedings Iron Ore 2013, pp 363-368 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By Maslov LA

We have considered the following characteristics of the crust and upper mantle of the Pacific Belt: seismic wave velocit> anomalies, mechanical stress and shear deformation rate fields, heat flow and the pattern of metallogenic provinces of the Belt. It has been noted that there exist certain regularities in distribution of the above mentioned geophysical characteristics and metallogenic zones within the Belt, displayed by prevalence of the lithophile elements in the Asia-Australian part of the Belt, and of the chalcophile ones within the American part.

Jan 1, 1995

The effects of changes in sintering bed height, coke fuel, suction and basicity on sinter productivity, physical strength and mineralogy were determined. It was found that, for a given iron ore, there is a narrow -coke range which maximises sinter strength, irrespective of bed height (in the range 300 to 500 mm) or basicity (in the range 1.2 to 2.2). Increases in bed height, at a constant coke level, improved the physical strength of the sinter. Productivity increases were obtained by increasing the sintering suction but, at coke levels other than the optimum, these *ere somewhat offset by the decrease in sinter physical strength. At basicities higher than 1.2 (i.e. 1.6, 1.8 and 2.2) there was a narrowing of'the size range of product sinter, with a decrease in the percentage of top size material, and a decrease in the amount of fines produced. Changes in coke, bed height and basicity exert major effects on sinter mineralogy, while the Nagoya index was mainly influenced by cote and bed height Changes.

Jan 1, 1975

Low tonnage quartz vein-hosted stibnite lodes are widely distributed in rocks of the Tasman Fold Belt System in eastern Queensland, with particular concentrations in the Hodgkinson - Broken River Fold Belt and to a lesser extent in the Gympie Province of the New England Fold Belt: Higher grade deposits have been worked intermittently on a small scale since 1873, resulting in the production of about 5500 tonnes of antimony ore/concentrate with an estimated grade of about 55% Sb. Future production of antimony may be as a by-product from deposits, currently being explored/mined for gold in the Hodgkinson/Mitchell River area and the Amanda Bel goldfield. Establishment of an antimony processing plant in Queensland using the Quelar Process would provide a more reliable market for small producers and could stimulate future exploration and production.

Jan 1, 1990

By S Pollak, A Amon

This paper describes the current and finished design work which has been performed for shallow rock station caverns for New York CityÆs first new subway construction in 60 years. A new robust, sophisticated, design procedure has been developed for two up to 30 m wide caverns, with overburden of less then 12 m, and rock cover to span ratios (C/S) in the order of 0.25. The design is based on empirical input parameters like the Q-value, rock mass rating (RMR) values, rock mass class after Cording (1984), cover to span ratios, which have been validated by the use of structural computer models as well as two- and three-dimensional numerical discontinuum models. The design approach is a staged approach using first principles, empirical models and non-linear FEM and DEM models. In addition, the paper describes the factors and circumstances why shallow caverns have been selected instead of cut-and-cover structures and why all the underground station structures have been developed as drained structures.

Jan 1, 2008

Information from bores in the LatTobe Valley has been accumulating for over fifty years, and the manual extraction of details has become a limiting factor in their use.Punched card equipment, installed by the State Electricity Commission for accounting purposes, was known to be available for reasonable periods, and it was suggested that this could help in the extraction of data from the voluminous records.Investigation showed that they could be substantially duplicated on cards, with consequent gains on many operations; the cards being regarded as an auxiliary to the existing records.BRIEF DESCRIPTION OF RECORDSAs a bore is drilled a continuous record of the strata is kept, together with notes on the presence of water or any unusual features which the driller may observe.When coal is struck, samples of each ten feet are usually sent for analysis.The location and surface level of each bore is fixed by surveyors, and details of dates and methods of drilling are also kept.Bores are allocated numbers, prefixed by the name of the parish within which they are drilled. Numbers are allocated in conjunction with the Department of Mines, to avoid duplication.Records of strata and analyses are kept in folders, with 100 bore numbers per folder.Standard plans are drawn, showing the locations, bore numbers and surface levels. For each bore they also show the depth and thickness of coal struck, and the total depth drilled.Cross sections are then drawn, connecting the various coal seams, which have been identified by the geologist.

Jan 1, 1960

I must tell you at the outset that I come to this conference deeply disturbed at the `role of Government in international dealings in mineral and energy resources'. I am disturbed by the confusion that now passes for policy. I am disturbed by the short- range view of critical problems taken by a majority of Governments. I am equally disturbed by the even shorter range of view taken by a growing army of industries. Many of them clamour for Governments to solve their problems in a specific way, with little regard for any other sector but their own-and with even less regard for the fact that every time a Government takes over some of their responsibilities they surrender some of their freedom. I would not say that longer range views don't exist. But I would say that they don't prevail at the present time. Instead, we are seeing the con- stant development of many policies for individual problems which don't tackle the fundamental causes. We must get back to basics without delay.

Jan 1, 1978

By Mauk JL, Arehart GB, Mathews SJ

The banded nature of the quartz veins which form the Empire lode at the Golden Cross mine, is perhaps their most striking feature. Petrographic studies show that significant differences occur between the bands in terms of textures, quartz grain size, calcite, adularia and kaolinite content, and the form, concentration and mineralogy of sulfide phases. The 818Oqu i values of individual bands within the vein material range from 7.3-10.9%x. Calculations show that the 818Oqäa,u values can be adequately explained by temporal variations in the system temperature, boiling and/or variations in the systems fluid/rock ratios.

Jan 1, 1995

By Bhaskara Sarma P V R

Solvent extraction of cobalt from an ammoniacal ammonium sulphate medium was carried out using Di(2-Ethyl Hexyl) phosphoric acid in kerosene as diluent. The effect of ammonium chloride and ammonium sulphate on the extraction efficiency was studied. The extracted species in the ammonium chloride and sulphate systems were CoAz2HA.NH4CI and CoA3.HA.2(NH4)2SO4, respectively. Ammonia scrubbing and cobalt stripping studies were carried out from loaded and ammonia free organic Respectively.

Jan 1, 1992

By Salmon P. T, Gilmour R

Commercial production of zinc started at the Pasminco Metals - EZ Plant, Hobart, Tasmania, in 1921. Since that time the capacity of the plant has been steadily increased to its present level of almost 220 000 tpa. Major areas of the plant have been successively upgraded over a number of years, (Roasters, 1969, 1975; Acid Plants, 1981; Casting, 1972; Residue Treatment Plant, 1971), but, until recently, the leach/purification area remained virtually unchanged from the time the plant was built. The major redevelopment of the hydrometallurgical plant began with fully integrated pilot plant testing of the proposed new circuit in 1981. The pilot plant incorporated the Low-contaminant Jarosite Process, and a new two-stage zinc dust purification procedure. In 1985, approval was granted for a major modemisation program which involved the complete replacement of most of the leaching and purification plants, and substantial improvements to the residue treatment plant. Construction of the first of the new plant sections, Strong Acid Leaching, commenced in 1986. This paper describes briefly the modernisation program itself, and the current method of zinc production at the PMEZ plant. The new plant sections comprise a Strong Acid Leach stage to improve lead residue grade; a Preneutralisation stage to reduce metal losses in jarosite; new filtration stages for both jarosite and lead residue; new Neutral Leach and Weak Acid Leach stages to replace old equipment; a new Solution Purification stage to replace the use of organic reagents to remove cobalt; and a new Gypsum Removal stage to cool the solution before electrolysis. At the completion of the modernisation program, only the electrolytic cellhouse remains of the early plant sections.

Jan 1, 1993

Esso Australia Ltd. operates a large natural gas producing system in the Gippsland Basin, supplying gas to the Gas and Fuel Corporation of Victoria, the State Electricity Commission of Victoria and several industrial customers. Gas reaches the Longford processing plants from three offshore platforms via a network of large diameter pipelines, which must be protected against the formation of ice-like hydrates. When gas production commenced in 1969, methanol was used to inhibit hydrate formation in the offshore pipelines. However, later investigations showed that the methanol was causing excessive degradation of molecular sieve in the onshore gas-processing plants. (Molecular sieve is used to remove water and H2S from the gas prior to further processing to remove heavy hydrocarbons.)

Jan 1, 1982

Detailed mapping in the Permian-Triassic clastic sediments of the Southern Alps delineates a number of strike-slip faults, both dextral and sinistral, associated with the major Alpine Fault to the west and displacing a tight array of fault blocks. Concurrent steeply plunging folds are deforming early major folds of probable Cretaceous age, and generating schist locally. To the east a major collapse zone has developed along the crest of a Cretaceous anticline, located over an ancient Permian submarine scarp, with a number of small normal faults. Further east, extensive Carboniferous to Triassic rocks of much the same appearance are exposed as horsts and grabens in a large possible extension zone through central and east Canterbury. This may have crept incrementally from Cretaceous from the offshore Bounty Trough to reach the eastern margins of the Southern Alps in the Pleistocene.

Jan 1, 1990