Search Documents

WINDING engines are one of the most important units in the equipment of a mine. Upon the winding machinery depends not only the output of the mine, but it supplies in most cases the only means by which workmen enter and return from the mine, and consequently the utmost care and attention is desirable in its design. The efficiency of a direct acting winding engine, as a machine is very low. In other words, the proportion between the useful work performed and the actual work the engine is capable of performing (under the most favourable conditions) is very small. The reasons for this are:-1. The intermittent nature of the work; the engine is stopped from 20 to 25 %(or even more) of the time which would constitute a useful day's work.2. The large amount of power that is absorbed applying the brakes to bring the load to rest.3. That the net useful load raised is small in comparison with dead load to be lifted, and the parts to be set in motion.4. That, owing to the frequent stops, initial condensation in the cylinders is always greater than in a continuously running engine, whilst radiation from steam pipes, valve chests, &c., goes on whether the engine is running or...

Jan 1, 1911

In the last 40 years nuclear energy has taken its place as a major source of electricity worldwide. It now produces 17 per cent of the world's electricity and could conceivably produce a higher proportion, to displace some six billion tonnes of carbon dioxide emissions per year. Concerns about global warming and environmental quality now underline the virtues of nuclear electricity among alternative sources of energy. Global electricity demand is rapidly increasing as a proportion of total energy usage. The proportion has doubled since 1960 and the demand is expected to increase at least 75 per cent between now and 2020. The source of this extra capacity, and the replacement of present capacity, raise questions with major resource and environmental implications. Today nuclear energy is a mature technology. Over 1200 nuclear reactors have been built and operated, some of these have been decommissioned, and among the 440 reactors in commercial operation the first advanced reactors are now entering service. Some 8000 reactor-years of operation have, with the sole exception of Chernobyl, shown nuclear energy to be extremely safe and reliable. High-level wastes are being managed properly and in different parts of the world two strategies are applied to this. Australia has a major role as a long-term supplier of uranium, since it holds almost 30 per cent of the world's reserves. This, along with an impending sellers' market for uranium, is making it an opportune time to develop new mines here. However, after several decades of concern about civil nuclear energy contributing to the arms race, we now have uranium liberated from nuclear weapons stockpiles being diluted for use in civil reactors, which will supplement ex-mine supply. The public acceptability of nuclear energy remains the critical factor in its future and hence in ours.

Jan 1, 1997

By Holliday R, Floyd JM

A laboratory investigation was carried out to determine the distribution of gold between the products of lead-zinc concentrate smelting in the Imperial Smelting Furnace (ISF). Bullion, speiss and slag from the ISF at Cockle Creek were used as the starting materials to evaluate the effect of gold and copper content of products on the distribution of gold between phases under conditions simulating those in the ISF hearth. The ratio of gold in bullion to gold in speiss has a mean value of approximately 1.6 and is independent of the gold content of the bullion. The distribution coefficient of gold between bullion and speiss is dependent on the copper level in speiss and is lowered by increasing copper content in speiss. The ratio of gold in bullion to gold in slag is in the range 25 to 5700 and dependent on the gold content of the bullion. For low gold concentrations in bullion of the order of 1 g/t and a bullion to slag ratio of 1:3 the gold loss to slag is expected to be approx- imately 23%. In all tests the gold in slag remained low, in the range 0.05 to 0.5 ppm provided metal prills were not suspended in Slag.

Jan 1, 1986

By C McIntosh, M van Dam, N Whetter, R Lane, M McCulloch

Mine geology is understood through synthesising large amounts of structural, lithological, geochemical and geophysical data derived from the original topographic surface, drilling and surfaces exposed and removed during open cut and underground excavations. Computer- generated 3D geological models of any mine environment need to incorporate large amounts of information but also should be regularly updated with typically frequent influxes of new data. Geologists with the local knowledge should also be involved in the model construction, enhancement and interpretation, placing ease-of-use functionality high on modelling software requirements. Implicit-style modelling is a fast-growing area of 3D geological software development where interpolated surfaces such as lithology boundaries and bedding orientations are defined mathematically as functions rather than explicitly through coordinate meshes. The functions are constrained only by the data and not by an artificially imposed grid; therefore, implicit 3D modelling can process a lot of information quickly and routinely operate on original data (such as observed contacts and structural data) rather than on evolved iterations and interpretations. 3D mine geology models can be readily updated with new data, which can be automatically reprocessed to test ideas in near-real time. Implicit, function-based 3D modelling software has been applied to the Globe-Progress mine in West Coast, New Zealand. This structurally- hosted gold mine has some geometrical conundrums that are in part being resolved as excavation of the open pit proceeds. The relationship of the Globe-Progress ore shoots to hanging wall and footwall structure is still not fully understood, however, and 3D geological modelling is assisting with visualisation and testing of structural hypotheses. The modelling is also capable of predicting areas of bedding defect slope failure in yet-to-be excavated parts of the mine.

Jan 1, 2009

By Duncan GR

Having passed through a number of previous phases the best longwall results in Australia have shown a significant increase in the last two years. The results expected from a longwall face can be estimated from the ideal production rate, determined by the capacity of the equipment and the conditions in which it is installed, the utilisation, and the available operating hours. Back analysis of the results achieved suggests that, on average, recent improvements arise from the higher capacity equipment recently installed; the utilisation has in fact reduced slightly. Review of the constraints which limit the longwall results, i.e. shearer speed, AFC capacity, support, advance rate, and man travel speed, shows that little improvement can be expected in the ideal production rate in thinner seams. In thicker seams the AFC often proves the overriding constraint and further increase in equipment size could lead to increased future ideal production rates and is expected. In all cases a concerted effort to increase the utilisation achieved is likely. For deep mines with thin to medium seams this offers the most viable path to improvement; by contrast thick seams with highwall/shallow access may benefit from further increase in equipment size.

Jan 1, 1988

The winning and upgrading of mineral raw materials necessarily includes size reduction, which serves the liberation and production of marketable products from highly valuable and bulk materials. For crushing, the following factors can be duly accounted for depending on material type and the selection of the suitable machine: ò producing a particular size distribution, ò producing a particular grain shape, ò selective comminution, ò gentle comminution, and ò producing a size range required by a specific process and/or for a specific product.

Jan 1, 1993

Extraction under very mild conditions - a few minutes at room temperature with poor solvents - yields results characteristic of surface properties for a variety of coals. Such superficial extractions preferentially remove long-chain aliphatic compounds. As coal becomes more oxidized, less of these yellow- colored compounds is extracted, forming the basis for a simple colorimetric test for coal surface quality. The fact that these aliphatic compounds are responsible for surface hydrophobicity is supported by good correlation between extraction results and floatability, which decreases with decreasing extractability. This extraction test is very sensitive to oxi dationb even the effect of heating for an hour at 100 C can be detected. A second extraction test using mild alkali conditions has shown good correlation with plant dewatering Operations.

Jan 1, 1986

By Gregory L. M, Phillips G. N

Although it has long been recognised that there is a diversity of minerals associated with Victorian gold deposits, the degree to which this mineralogy is systematic or haphazard has remained uncertain. Recent work by the authors and students under their supervision permits a sharp delineation of the boundaries between different mineralogical domains, and these are interpreted in terms of recent rapid advances in Victorian tectonics, and the regional framework of Victorian gold geology described in Phillips and Hughes (1996).

Jan 1, 1997

By Kelley BC, Filmer AO

The chemical oxidation kinetics of sphalerite by Fe(III) was studied at various temperatures and size fractions in sulphate media. The kinetics of Zn extraction followed a pore diffusion control mechanism with an apparent activation energy of 54-58 kJ mole. This figure, although high for a pore diffusion control process, is consistent with other studies carried out in sulphate media. An empirical statistical model, relating the extraction time to % Zn extraction, average particle size and temperature, is described by log 1 = 12.22 - 0.017% Ext. - 1.76 log D Av t - 2954 T Parallel studies were also carried out investigating the biological oxidation of sphalerite utilizing the acidophilic autotrophic bacterium Thiobacillus Ferroxidans. The effect of such kinetic parameters as pulp density, particle size and Fe(III) on bacterial growth rate and consequently zinc extraction rate, were studied and where appropriate, optimum conditions for bacterial growth were specified. Based on the results of chemical and biological leaching studies, it was apparent that rapid zinc extraction from sphalerite was predominently due to oxidation by Fe(III). The biological oxidation process catalyses the oxidation and regeneration of Fe(III). The proposed combined chemical-biological leach system was simulated in semi continuous fashion. The sphalerite oxidation rates obtained in this system were similar to that predicted by the chemical leach empirical model. 1. Senior Research Metallurgist, CRA Research, Boolaroo, N.S.W. 2. Group Leader-Hydrometallurgy, CRA Research, Boolaroo, N.S.W. 3. Senior Research Scientist, Biotechnology Australia, Roseville, N.S.W. 4. Senior Experimental Officer, Biotechnology Australia, Roseville, N.S.W.

Jan 1, 1986

By Hendrix J. L, Nelson J. H

A model based on non-steady state has been developed for dissolution and diffusion in porous ore particles. Results from the particular model have been incorporated, as a rate term, into a global, heap-scale model based on a plug flow reactor at unsteady state. The global model can be used to consider leaching by aqueous-phase reagents in equilibrium with a gas- phase component, such as oxygen gas, as well as strictly aqueous-phase reagents, such as cyanide. The flexibility of the model even allows predic- tion of the outcomes of using reagent sideflow injection in large heaps. Data from column leaching tests are compared to the model, and their relationship is discussed.

Jan 1, 1991

By Gillies A. D S, Just G. D

Coal washability data can be used for assessing coal quality. However, the techniques of using these data to solve quality problems differ from one mine to another and certain problems may never really be investigated due to limitations of the available techniques. One promising way to overcome these limitations is by correct application of geostatistics.A geostatistical study on coal washability data was undertaken based on a data set of closely spaced in-pit bore cores. These bore cores were analysed consistently over a relatively simple geological area. The average distance between the drill holes was about lOOm. There were 78 drill holes available for the area after deleting the erroneous bore cores. During the study, nine extra closely spaced drill holes were drilled within a single mining block.A procedure to construct two coal quality models, a kriging or cokriging model and a simulation model, was proposed. The modelling results for the data above are discussed and results of a mine scheduling exercise based on the models developed are included.

Jan 1, 1992

By Wooller R

The 3-D regular block model used for long term mine planning at Hamersley Iron did not fulfil the requirements for short term mine planning in terms of accurate representation of geological structures, contacts and boundaries in the orebodies. A computer model, based on zone plans, is being created as a single orebody model for all phases of mine planning. The zone plan is the primary interface between the geologists and mining engineers. It is essentially a bench plan at mid-bench height showing geological structure, material type boundaries, the grade and physical characteristics of ore blocks. The method allows for the dilution of ore zones by waste material. The stratiform nature of the orebodies allows zones of varying grade to be readily delineated on the plans. The Zone Plan Model (ZPM) is the interface between geological and mine planning computer systems. It is the basis of all mine planning with applications including long and short term mine plans, reconciliations, general ore reserve estimations, pit design and general model enquiries. The system was designed to be user driven. The user has complete control at all times as all computer generated data are fed back to the user who may then elect to override the computer. Various controls were built into the system to ensure model validity and integrity. The system has proved to be invaluable as a tool for users with little or no computing experience.

Jan 1, 1986

By Preston JC, Richards DJ

A multicommodity exploration programme was mounted in the 1970s by CRA Exploration Pty. Limited over a major part of the southern Murray Basin in Victoria. Commodities sought were brown and black coal, gold, uranium, diamonds, titanium and zirconium rich heavy minerals, and base metals. An area of 40 000 km2 was held under exploration licences by the Company. Exploration techniques used were literature research, airborne magnetics and gamma ray spectrometry, drilling, and geophysical well logging. Targets were defined in both the Tertiary basin sediments and the underlying Palaeozoic sedimentary and igneous rocks. Although exploration is continuing, large resources of brown coal and low grade titanium rich heavy minerals have already been discovered. Exploration for uranium was abandoned in accordance with statutory requirements. The search for significant resources of the other commodities has not been successful.

Jan 1, 1986

By Grano S. R, Kilgariff B

The Renisun Tin concentrator treats an ore containing I's per cent till as cassiterite and 22 per cent sulphur in a range of sulphide minerals. predominantly pyrrhotite. The sulphide minerals are removed by flotation using copper sulphate (CuS

Jan 1, 1997

By Mutton B. K

Hilton Mine is being developed as an integrated component of the Mount Isa operation, to achieve continuity of silver/lead/zinc production well into the next century. The mine has a chequered history from its discovery in 1947 through several periods of intense development activity, each of which has been curtailed due to the further development of the Isa Mine operation. This era has now passed; to sustain increased production rates at Mount Isa, there is a requirement for Hilton ore in 1989. The decision was made in 1983 to accelerate the programme of Hilton development by installing skip hoisting facilities in the main service shaft (P49), to facilitate the development of the mine to pre-production status. The Hilton development plan provides for the mining of selected orebodies, a broadening of the underground exploration drilling programme, and the establishment of significant mine infrastructure. Several technical challenges have been identified as important. The Hilton orebodies, although occurring in the same rock type as Isa Mine, are more faulted, jointed and intersected by intrusive dykes. The ore is more variable in terms of ore continuity, boundaries, grade and metal distribution and the mineralogy more complex. As a consequence the development of this project consists of a co-ordinated programme of mine exploration and development, rock mechanics investigations and metallurgical research and development work. Production will commence in 1986 at a rate of 1000 t/day using mechanized cut and fill techniques. It is planned to introduce sublevel open stoping and by 1996/97 the production rate will be 2.5 million t/yr.

Jan 1, 1986

The Macquarie Dictionary defines `information' as: knowledge communicated or received concerning some fact or circumstance; (in communicating theory): a quantitative measure of the contents of a message. For mining companies investing in data capture and information processing technology for operations management is a key issue. Beyond producing performance related information that employees can relate to it is being able to deliver that information into the workplace when it is required, to the employees that can utilise it. To be effective the data needs to be received and understood as `information'. The technology is now available and proven to enable `information' to be delivered into the mining workplace adding value to the activities performed by mine employees. The application of computers and information technology in the mining industry has typically been limited to the resource definition and planning stages, accounting and administration and the process plants that treat the ores and minerals. The mining extraction processes that consume expenditure and determine output in a mining operation occur in an environment dominated by unpredictable events and variable conditions. The mining operation has long been regarded as an inexact science conducted in unpredictable circumstances with many independent variables affecting the output and resultant cost of production. Financial accountants keep track of expenditure and management accountants analyse the cost of production usually on a weekly or monthly basis but all this effort can't affect the outcome, that was determined by the real time events and variations of circumstances over a week ago. Such reporting and analysis can result in conclusions being drawn about what improvements can be made and how you might do better next time, but generally the data is not detailed enough, is inaccurate or misrepresents the real issues. The capital investment required for any mining operation is substantial and comparable to other industries such as manufacturing. The performance and utilisation of manufacturing plants is usually closely monitored down to the lowest level of detail. Many modern plants are controlled and optimised using programmable intelligent devices and monitors display real time performance to the operators and prompt them to make informed decisions to maximise production and minimise wastage. Technology suitable for the mining industry is now widely available and has proven to be a reliable and powerful tool for the optimisation of mining operations. This paper focuses on the latest information technology developed by Modular Mining Systems that has been implemented in mining operations worldwide. The benefits reported by the mining companies utilising real time information technology over the past 15 years have generally related to optimisation of truck fleet allocation and material blending. Some mining operations have reported improvements in equipment utilisation of greater than 20 per cent. With the development of real time graphical display screens in the operators cabins the benefits of information delivery can be harnessed to make employees more effective in the workplace.

Jan 1, 1995

By Gray N. B

The need to improve existing metallurgical processes and to develop new processes to meet the economic challenges that lie ahead requires the application of the tools of process analysis viz. mathematical models, physical models, pilot plants, laboratory measurements and plant tests. Examples of the application of these techniques to processes are described in this paper. Several of these techniques, combined with basic knowledge, are necessary to make improvements and for existing processes this always involves plant measurements. Also because metallurgical processes include extraction, refining, alloying, casting, mechanical working and heat treatment, an interdisciplinary approach to research and development is essential. This paper argues that metallurgical engineering is a discipline that is uniquely able to encompass the broad spectrum of chemical- and physical-metallurgy processes and is therefore essential to the health of the metallurgical industry.Regrettably many metallurgical engineering departments are not offering courses on process analysis, control, optimization, etc so necessary to meet modern industrial challenges.

Jan 1, 1985

Geological information plays a significant, cost effective role, in the Mt Whaleback iron ore mining operations. The geology and structure are complex. Good communication between the Mine Planning Production Scheduling and Quality Control Sections is the key to utilisation of geological information to its full potential.Drilling and pit face mapping are the two basic sources of detailed data sets which are processed to prepare up to date geological cross sections and benchwise geological plans. This information is used directly for the blast pattern design and production scheduling. Physical ore type estimation is also undertaken. Orebody models are generated from the geological information.

Jan 1, 1990

By J Bower

The JORC Code does not specify a definition for ælevel of confidenceÆ. The common approach in the mining industry is to use a certain drill spacing or number of data samples to classify resources by the confidence categories. Another approach includes application of the quantitative geostatistical criteria for non-subjective and consistent definition of the resource categories. This approach, which has become increasingly popular in the mining industry, provides a quantitative measure of the resource estimation uncertainty. In this study, uncertainties associated with the different drilling grids at the Weipa bauxite deposit (Queensland, Australia) have been modelled using conditional simulation methodology. Criteria used at Weipa for defining resource categories are as follows: mineralisation can be classified as a Measured Resource if tonnage and grade of its volume representing three months of production can be estimated with a precision error not exceeding ¦10 per cent (at 95 per cent probability, ie two standard deviations); and mineralisation can be classified as an Indicated Resource if grade and tonnage of its volume representing annual production can be estimated with a precision error not exceeding ¦10 per cent (at 95 per cent probability). Several different grids have been created by subsampling the drill hole database. The studied variables include Al2O3, SiO2, thickness of the bauxite seam and location of the footwall contact. The variables have been modelled by sequential Gaussian simulation. Based on this study the following drill spacings have been recommended: Measured Resources û 150 m by 150 m, Indicated Resources û 300 m by 300 m.

Jan 1, 2009

Mt. Whaleback is in the Pilbara region of Western Australia approximately 1200 kilometers north of Perth, the State capital. In this deposit the Mt. Newman Joint Venturers are mining ore reserves totalling 1500 million tonnes of high grade hematite averaging 64.0% Fe. In addition to Mt. Whaleback, 38 ore bodies have so far been identified outside Mt. Whaleback on the Company's remaining 75,000 hectares of lease area. These ore bodies contain major tonnages of iron ore. Extraction at present is planned at a rate of 37 million tonnes per annum at an ore-to-waste ratio of approximately 1 to 1.4. The ore is railed north to Port Hedland on the Indian Ocean where the different products are screened, crushed and blended prior to shipping. The purpose of this paper is to acquaint the reader with the facilities installed in the Mt. Newman operation to form a background to the sampling techniques employed, describe the precisions which were achieved in experiments conducted February through June, 1976 and also to assess the degree of blending which takes place during the various processes and to put a quantitative measure to the degree of blending. There have been many excellent papers written on the more theoretical aspects

Jan 1, 1976