Search Documents

By P Ottenio, B CarrT

In the last 40 years, the froth flotation process widely spread in the paper industry becoming the dominant technology for ink removal from recovered paper slurries and cellulose fibres recovery. Most of current models used to describe the flotation deinking process are based on hydrodynamic and statistical theories of ink particles collision/attachment to air bubbles. The complexity of these theoretical models, together with the variability of the recovered papers composition, does not allow to define a set of æeasy to handleÆ equations to be used for modelling industrial flotation cells. This main limiting aspect makes that, in several deinking process modelling tools, basic parameters used to characterise the flotation unit, ie yield, ink removal efficiency, water loss, are constant parameters. Although in some process simulation tools the flotation yield/efficiency is adapted to process control parameters (air ratio, pulp flow, pulp consistency), physicochemical variables (namely the pulp frothing aptitude, the pulp surface tension and the ink adhesion energy to air bubbles) are not taken into account to adjust the flotation yield/efficiency. Data collected during recent laboratory and pilot plant experiments focusing on the role of surface active substances on the flotation efficiency were therefore interpreted and used to identify general trends that could be described with simple semi-empirical models. A set of model equations using surface tension and froth removal height as main variables was then defined in order to describe the behaviour of a pilot flotation cell. Trends obtained during the dynamic simulation of the deinking pilot plant were in good agreement with experimental data obtained under similar experimental conditions, thus indicating that developed equations can forecast with good approximation the behaviour of a flotation deinking unit.

Jan 1, 2005

By L Klemettinen, J Biswas, W Malan, D Sukhomlinov, D Lindberg

In order to mitigate the effects of climate change, our society must be able to drastically reduce its CO2 emissions. As the metallurgical industry is a considerable contributor to these emissions, new greener technologies must be invented and developed. One option could be the direct production of metals from oxides using renewable electricity. The aim of this study was to investigate the possibility of using high-temperature molten oxide electrolysis (MOE) for iron and ferrochrome production. FactSage™, ver 8.2 (by Thermfact Ltd and GTT-Technologies) was utilised for estimating a feasible equilibrium electrolyte composition, and the experiments were conducted at 1550–1580°C in conical alumina crucibles with iridium wire as the cathode and platinum wire as the anode. The sources of iron and chromium were either pure FeO powder or industrial chromite pellets. Voltage was applied to the electrolysis cell for 6 hrs and the resulting current was measured, along with oxygen concentration in the off-gas line. The electrolyte comprised of SiO2, Al2O3, MgO and CaO. First, the effect of FeO concentration on iron reduction efficiency was investigated using only pure oxide powders as starting materials. The results indicated that 10 wt per cent FeO mixed with the electrolyte resulted in more efficient iron reduction compared to 20 wt per cent. In further experiments, industrial chromite pellets were ground and mixed with the CaO-free electrolyte. Iron and chromium reduction efficiencies were higher when approximately 19 wt per cent of the total sample mass consisted of pellets compared to increasing the pellet amount to 37 wt per cent. Generally, the chromium solubility in the liquid electrolyte was relatively low, and most of the chromium was confined to the spinel solid solution, from where its dissolution to the liquid electrolyte was very slow, resulting in slow reduction kinetics. For larger scale applications, economically more viable electrode materials should be investigated.

Jun 19, 2024

Eleven years ago I addressed delegates to the Whyalla Meeting of this Institute on the subjects 'Oil in Australia?' -- a title which was followed by a large question mark.My purpose at that time, which was before Rough Range, was to interest members of this Institute in the possibility of oil in this country because I considered that exploration for mineralwealth was our concern.I doubt if I made much impression.but.I recall that the Chairman at that Meeting, Mr Ian McLennan, asked me pointedly to name the areas I-would select and I nominated the Northwest of Western Australia,'Gippsland and the Roma District

Jan 1, 1962

By G J. Harbort, V Lawson, L Reemeyer

The Jameson Cell is a high intensity flotation device, which utilises induced air from the atmosphere. It was developed jointly by Mount Isa Mines and Professor Graeme Jameson of the University of Newcastle in the 1980s. It is proven to generate fine bubbles, in the order of 300 to 500 ¦m, in a high intensity, high shear and compact zone contained in the downcomer. This aerated mixture exits the downcomer into the pulp zone, which is the quiescent mineral and gangue separation zone. A number of Australian base metal flotation circuits feature a reverse flotation stage at the head of the circuit. Testwork and plant operating data has shown that the use of a Jameson Cell in the prefloat cleaner application has further improved prefloat gangue recovery and selectivity. Operation of a Jameson Cell in a carbonaceous/pyrite prefloat cleaner duty at the Mt Isa copper concentrator increased copper recovery and reduced pyrite in the copper concentrate. Testwork at Zinifex Century Zinc Mine showed a decrease in zinc losses by the utilisation of Jameson Cell prefloat cleaner. Appraisal of a Jameson Cell in a scalping role within the Mt Isa Copper Concentrator indicated significant benefits could be achieved.

Jan 1, 2005

By H E. S Moorcroft, D Scott

The increasing mining depths of South African gold mine deposits are resulting in ever-increasing heat loads associated with depth and the geothermal gradient. Together with changes in the mining horizons brought about by the depletion of older, shallower, high-grade reserves, this leads to the need for the continuous review and redesign of cooling requirements. Traditionally, cooling requirements were met by using a combination of cooling strategies, including bulk air cooling on surface and underground. If this proved to be insufficient, chilled service water and secondary remote air-cooling systems were introduced. This paper reviews these practices in order to provide a cost-effective means of catering for the introduction of hydropower at the Gold Fields Ltd South African operations. Some of the equipment that has been developed to meet the requirements of both hydropower and refrigeration includes hydropower fans, cooling coils and in-stope venturis. These are individually described and discussed, together with their roles within the greater strategy. The planned change in the cooling strategy and the employment of these technologies have effectively doubled the cooling available, from 10 MW to more than 20 MW, extracted from the hydropower water used to drive the mining equipment. In conclusion, the cooling strategy described allows a total heat load of approximately 52 MW to be successfully ventilated and cooled through the use of combined surface and underground refrigeration installations, and through the use of hydropower-chilled water.

Jan 1, 2005

By F Brenguier, R A. Lynch, G Olivier

The seismic velocities of intact rock are dependent on the applied stress. Unfortunately, the low susceptibility of seismic velocity to stress changes mean that changes in seismic velocity have to be measured extremely accurately to infer stress changes from them. Previously, it was thought that measurements of this accuracy could only be made with active sources or repeating earthquakes. In this paper, we show that the noise generated by mining activity can be used to construct virtual seismic signals with which we can measure changes in seismic velocity accurately enough to see the short- and long-term effects of a production blast on the surrounding medium. The time-dependent velocity variations achieved with this method show that the blast caused weakening of the rock mass for the rock within a radius of 200 m of the blast. The weakening is healed by confining stresses over a period of five days, after which permanent changes in the seismic velocity can be seen. The size and spatial distribution of the seismic velocity changes were compared to modelled changes in static volumetric stress, which supported the notion that seismic velocity changes can be used to measure the redistribution of stress after a blast. The results of this study indicate that this method can be a powerful tool to evaluate the evolution of stress in a mine at a relatively low cost as the data that it uses would normally be discarded.CITATION:Olivier, G, Lynch, R A and Brenguier, F, 2016. Measuring the redistribution of stresses resulting from new excavations with ambient seismic noise correlations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 873–878 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S D. Dessureault

In one of North AmericaÆs largest mines, which contains more than six active coal-producing faces, mine controllers must meet the complex challenge of adhering to the mine plan while also ensuring customer quality. Fleet management systems (FMS) provide many different avenues to control production flows, from the faces to the various pit crushers. Nonetheless, mine controllers must balance a variety of factors such as unplanned downs, differing customer demands, their own daily key performance indicators (KPIs) related to equipment utilisation, among others. Deviating from the short-term mine plan is the most common means of balancing the other factors, since adherence to the plan is traditionally only measured during the weekly variance meeting with engineering staff. However, such deviation may be one of the most costly responses, as long-term scheduling issues may arise such as multi-face dead-heading or insufficient stripping. This paper focuses on the development of a system for real-time adherence to mine plan within a control room environment. This system is part of a larger blending-focused, multi-million dollar project with elements of a centralised remote control room, developed at the University of ArizonaÆs Mining Information Systems and Operations Management (MISOM) Mine Control Center (MC2). The mine plan (MPL) component of the overall blending system integrates both historical and real-time FMS data with mine plan requirements directly sourced from original systems (no additional input required). The measures, displayed largely as graphs, have tools to help controllers manage the production to facilitate adherence to the plan. Some measures are designed to motivate crews to perform by inciting competition between crews, softened through a study of the controller culture. The MPL component was deployed at the mine, and the before and after deployment adherence was measured. This paper discusses the technical development of the new tool, its deployment, and an ethnography (study of culture) to understand controller motivation.

Sep 26, 2011

By P Hatherly, A Melkumyan, D Wyman

Chemical species distributions in rock sequences can be modelled using Gaussian processes (GPs) to predict the weight percentage between known data points. This method can be improved by dividing the modelled area into regions of different mineralogy. In the context of many iron ore deposits, marker shales give the initial guidance of where these regions may lie. These shales give rise to distinctive peaks in the natural gamma downhole logs, which are conventionally identified by hand. A GP method has been developed to automate this task.Once the appropriate boundary has been located on the basis of shale occurrences, chemical assays from exploration drill holes are used to find the exact boundaries of interest. These boundaries divide the drill hole stratigraphy into regions of different mineralogy, each of which display their own distinct correlations between the main elements and oxides (Fe, SiO2 and Al2O3). Iron ore shows a negative correlation between Fe and Al2O3, but in banded iron formation (BIF) there is a positive correlation between these species. Similarly, SiO2 and Al2O3 have a positive correlation in the shales and ore but a negative correlation in the BIF. Correlations obtained within ore-, BIF- and shale-dominated regions are therefore better than those obtained using the entire log and can be used to improve the results obtained when modelling.

Sep 26, 2011

By D Chalmers

After the sustained use of the GAG (Górniczy Agregat Gaśniczy) engine at a Queensland coalmine, it has raised questions as to its effectiveness as a remote firefighting tool. All firefighting apparatus have advantages and limitations, however the deployment of any apparatus must be based on its likelihood to succeed and effectively extinguish the fire or bring it under control. A recent study conducted for ACARP by researchers at UNSW has highlighted that there is more to be learned about the GAG. As coalmines are mining at greater depths and fan pressures are much greater than they were when the GAG was introduced, deploying the GAG may be a total waste ofresources and may place operators at greater risk. When the GAG unit is positioned on the surface of the mine, the pressure it generates has to overcome buoyancy of the exhaust gases and the frictional resistance of the borehole and part of the mine circuit. Buoyancy in deeper holes can lead to the GAG pressure relief system opening, venting out the products to the atmosphere without delivering any product to the mine workings. Additionally, frictional resistance is a function of distance. Deeper holes will have a greater frictional resistance than shallow holes. Delivering sufficient products from the unit will be limited by the available pressure that has to overcome the buoyancy, and increased mine resistance thatconsumes any residual pressure. By documenting the limitations of this unit it will enable better decisions to combat a fire or spontaneous combustion event.

Oct 12, 2022

By M S. Manono, K C. Corin

The optimisation and process developments surrounding the beneficiation of Cu-Ni-PGM ores is of fundamental importance when considering the continued rise in global demand for these precious metals. The selective sequential flotation of these ores is accompanied with various processing challenges such as the successful separation of the Cu-Ni-PGMs from non-sulfide naturally floatable gangue and pyrrhotite. Reagents such as sodium iso-butyl xanthate (SIBX) and sodium carboxymethyl cellulose (CMC) have proven to significantly improve the selectivity of the flotation process in their respective roles. The use of recycled water with abnormal inorganic electrolyte concentrations can modify the selectivity of these reagents, as ions may adsorb onto minerals such as pyrrhotite, thereby hindering or promoting the hydrophocity and floatability of pyrrhotite. Process water quality effects on the behaviour of pyrrhotite may have negative or positive influence on the recovery and grades of the wanted Cu-Ni-PGMs as valuable minerals associated with pyrrhotite such as pentlandite may be affected in like manner. Thus, the impact of concentrator process water quality on the behaviour of pyrrhotite needs to be determined. In this study synthetic process water at various ionic strengths was investigated against various CMC dosages to understand the behaviour of pyrrhotite during the flotation of a Cu-Ni-PGM Merensky ore in a batch flotation cell. This study showed that pyrrhotite grades increased with an increase in CMC dosage for fixed ionic strengths whereas the recoveries of pyrrhotite increased with an increase in ionic strength until 3SPW, then a trend of a decrease in recoveries was seen with 5SPW resulting in the lowest pyrrhotite recoveries. Furthermore, this study showed that moderate CMC dosages of 100 g/t resulted in the highest pyrrhotite recovery for all four ionic strengths of synthetic process water tested. It can be said that to maximise value recovery from Cu-Ni-PGM ores, understanding the behaviour of pyrrhotite against degrading water quality and reagent suites could be of paramount importance given the sensitivity of pyrrhotite to oxidising chemical conditions.

Aug 24, 2022

By M I. Pownceby, M A. Rhamdhani, S Purohit, G Brooks

The use of concentrated solar flux for high temperature metallurgical applications is a wellresearched area with several reported literatures on solar calcination and metal oxide reduction. This paper presents two such processes with potential to reduce the carbon footprint from ironmaking through using concentrated solar flux. The first process involves solar flux incorporation to the recently developed lime-magnetite pellet (LMP) route of magnetite ore agglomeration. The second process is a hybrid solar-smelting route for iron ore-coal composite pellets that utilises solar flux to provide process heat. Both the concepts of solar agglomeration and solar smelting process were investigated using a solar simulator-hybrid reactor set-up at Swinburne University of Technology. Results from solar agglomeration experiments at 950°C suggested no change in the reaction mechanism of the LMPs under solar irradiation compared to electrical heating. The percentage and morphology of the primary phases (mainly CaFe3O5) appeared similar for both solar and electric heated LMPs. The solar-smelting of magnetite concentrate-lignite coal composite pellets at 1130°C showed a maximum metallisation of 55 per cent after 1.5 hrs of reaction. The solar-smelt process has about 25 to 35 per cent lower CO2 emission compared to the blast furnace ironmaking. Technoeconomic analysis of implementing a CST facility in an existing composite pellet process suggested a payback period of about ten years at a heliostat cost of $A100/m2 and natural gas cost of A$10/GJ. The economics of CST implementation can be further enhanced by decreasing the thermal losses from the heliostat field and reactor.

Nov 8, 2021

By C Zhang, R Liang, I Canbulat, S Saydam, B Li

The integration of digital twins in mining represents a significant advancement towards enhancing operational efficiency and decision-making. Central to this development is the role of visualisation, a crucial element in mining digitalisation. This paper aims to develop a data-driven visualisation solution for the construction of mining digital twins, highlighting how this innovation revolutionises the representation of physical mining environments. It spotlights the shortcomings of conventional visualisation methods, particularly their inability to accurately depict complex underground environments and their predominantly historical orientation. To address these challenges, this paper proposes a novel, data-driven approach. This approach extensively utilises CAD files, encompassing data from geological surveys to intricate mine plans, thereby significantly elevating the precision of digital twins. It supports real-time updates and enables flexible interaction with a variety of data types. Moreover, it introduces a comprehensive data diagram alongside the adaptation of a 3D tile index. This strategy ensures the efficient rendering of extensive mining environments, allowing for a more dynamic and interactive digital twin model. In conclusion, the implementation of data-driven visualisation in the construction of mining digital twins marks a pivotal advancement in the industry’s digital transformation. It promises a more detailed, accurate, and dynamic depiction of mining operations.

Sep 1, 2024

By MattelmSki M

Outokumpu Harjavalta Metals Oy has been producing nickel since 1962, based on conventional flash smelting technology followed by electrowinning of nickel. In the 1980s, a research project was initiated to develop a converterless direct smelting process to produce matte for further refining in the then existing refinery. The process was tested on a pilot plant scale at Outokumpu's research centre in Pori and was found to be viable. The process was named the Direct Outokumpu Nickel Smelting Process or the DON Process. At the turn of the 1990s, Outokumpu studied various options to develop its nickel business and the Harjavalta operations. As a result of this work, the DON Process was further developed to produce two mattes: low iron matte in the flash furnace to be leached in the existing leaching circuit and high iron matte in the electric furnace to be leached in the new leaching circuit. In Harjavalta's case, it was essential and important that the process could use the existing flash furnace and electric furnace without converters.

Jan 1, 1996

The performance of the Australian Mining Industry over the past 10 years using key indicators of production, revenue, aftertax return investment, together with key cost elements, market changes and ore reserves is briefly reviewed. The elements of competitiveness are discussed forthe industry and the effects of Government charges and policies relating to existing operations are outlined. There is a demonstrated need for improvements in competitiveness in direct and indirect costs and for improved access to resources for the mining industry to continue to grow and add to Australia's economic growth.

Jan 1, 1987

By B Saunders, J Carpenter

PanAust’s Phu Kham copper-gold operation (Phu Kham) in Laos is currently limited by throughput in the Semi Autogenous Grinding (SAG) mill. The ability to accurately predict SAG mill throughput (throughput) is therefore critical to accurately forecast copper and gold production. During the fourth quarter of 2016 the proportion of hard unweathered rocks in the mill feed increased, resulting in a period of lower than expected throughput. These low throughput rates prompted a study with the aim of identifying a practical solution for throughput predictions. The study identified an empirical modelling approach based on actual SAG mill throughput rates. The empirical model was then optimised by linear programming to identify the ideal feed blend of unweathered rocks to achieve a maximum SAG mill throughput.Rock strength was the initial focus of the throughput study at Phu Kham because previous studies had identified a strong link between rock strength and throughput. It was determined that there was insufficient valid data to adequately model but sufficient data to qualitatively characterise rock strength. The data identified that the weathering and lithology had a controlling influence on the rock strength. Complicating throughput predictions were operational improvements (changes to blasting and mill settings) implemented in response to the lower than expected throughput. This created uncertainty with the throughput equations. A self-learning empirical modelling method was developed to predict the throughput by incorporating fundamental rock properties with operational practices and improvements. The method is based on the proportion of mill feed with similar weathering and lithology (a proxy for comminution performance) and the actual mill throughput using the SAG mill as the analytical instrument. The modelling method simultaneously incorporated the sum and interaction of unmodelled influences including blasting, crushing and mill settings. The empirical modelling method worked at Phu Kham because the lithology and weathering has an intuitive and observable controlling influence on SAG mill throughput. The modelling method is described along with a worked example of feed blend optimisation using linear programming.CITATION:Carpenter, J and Saunders, B, 2017. Empirical mill throughput modelling and linear programming for blend optimisation at the Phu Kham copper-gold operation, Laos, in Proceedings Tenth International Mining Geology Conference 2017, pp 291–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By A Bennett, S Arndt

Minerals and Metals Group Pty Ltd (Golden Grove Mine) commissioned a comprehensive study of the life of mine using advanced 3D stress modelling. Essential input into the modelling was the proposed mining sequence, itself the culmination of years of planning and geotechnical experience gained in comparing actual performance to predictions. The modelling approach addressed the whole of mine at a scale of 5 km. There were however several magnitudes of scale to address, from the scale of laboratory testing (0.05 m), to drive size (5 m), extraction size (50 m) and stope size (500 m). Scaling was therefore an integral part of the procedure. The constitutive rock properties in terms of peak and post-peak behaviour varied with the scale. At the laboratory scale, the constitutive relationships for all the main rock units were determined in 3D as well as recovering the in situ stress using the rock memory technique, deformation rate analysis (DRA), whereas at the larger scale the properties were varied to match observations.The modelling, using non-linear analysis to account for rock mass yield and peak-residual strength, demonstrated that if the planned extraction sequence and stope geometry had been pursued there was a high probability of large volumes of excess shear stress being released. However, it was not possible to identify whether the excess shear stress (ESS) will release as one large event or many smaller events. The mining approach was to modify the extraction sequence/stope geometry to manage the hazard. This is where the economic advantage can be realised.Alternatively or in combination with further modelling, the volume identified with the predicted high ESS or energy release could be intensively explored for structures having adverse orientation to the stress change and with sufficient areal extent to release the ESS. The microseismic data can be interrogated for the likelihood of a large event to support the hypothesis of a singular release versus multiple releases of smaller events. If the initial planned extraction sequence had to proceed as designed, changes to dimensioned stopes would be recommended for risk mitigation. Mine planning could as an option, modify the sequence and the extraction could then be remodelled.CITATION:Bennett, A, Arndt, S and Dight, P M, 2014. The economic advantages of detailed geotechnical assessments for extraction sequencing, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 243–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By K M. P Singh, K M. K Sinha, G S. Jha, T Gouricharan, K K. Sharma

The majority of the powerplants in India are fed with non-coking coals, with the coals dispatched from their respective mines via wagons loaded by a rapid loading system or pay loader. The usual top size of coal is 200 mm and sampling is carried out manually from wagons. The manual method of wagon top sampling of large size raw coal is not only difficult, but also violates some of the fundamental principles of sampling. As per sampling requirements, samples are to be drawn from the full depth of the wagons, which is impossible to be done manually. Since the ash distribution in the different size fractions is not homogeneous, the results from the samples, which do not reflect the true size distribution of the lot, are likely to be biased. More importantly, sample collection by shovel from the top is a function of human discretion and not governed by the equiprobability rule. In another case, the sample has been collected by a cross belt-type auto mechanical sampler for 200 mm size coal at one of the super thermal power stations. Test analysis shows that coal collected using a cross belt-type mechanical sampler also has significant deviations from stopped belt coal samples of 200 mm size due to size segregation. Studies carried out on wagon top sampling through specially designed experiments reveal some interesting features. The presence of bias in wagon top sampling is apparent when compared with the ‘stopped belt’ sample. In this paper, a comparative study between manual wagon top sampling/auto mechanical sampling with respect to stopped belt sampling has been conducted for coal of size 200 mm. In addition, precision studies have been performed for wagon top sampling/mechanical sampling for Indian thermal powerplants.CITATION:Sinha, K M K, Sharma, K K, Jha, G S, Singh, K M P and Gouricharan, T, 2014. A comparative study of manual wagon top sampling and auto mechanical sampling of 200 mm size coal with respect to stopped belt sampling of thermal coal at Indian super thermal powerplants, in Proceedings Sampling 2014 , pp 43–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By B Olsson, B Reynolds, R Norman

An unprecedented growth in demand for coal exports has placed pressure on multi-user coal chains to guarantee that their capacity expansion projects will meet the required demand. These projects, however, are taking place in an increasingly complex commercial and technical environment - competing rail and coal terminal service providers as well as a myriad of competing mine operators, all needing to operate in an increasingly integrated manner to get the most out of expensive shared assets.Increasing system complexity and integration has driven the need for more holistic and sophisticated analysis tools. The capacity of coal chain subsystems, such as mine, rail and port, can no longer be determined effectively in isolation. Understanding the nature of the interactions between these subsystems, their sensitivity to uncertainty and the resultant capacity of the integrated system is the key to both maximising value and minimising risk.Recently, TSG has worked closely together with the Integrated Logistics Company and a number of key stakeholders in the Dalrymple Bay Coal Chain to develop independent system master plans. These master plans have provided a quantitative and rational assessment of coal chain capacity in its current state and a prediction of its capacity once a pipeline of committed capacity improvements is in place. This paper provides an overview of the study and a comprehensive guide to the process required to effectively achieve valuable strategic insights in a challenging multi-user stakeholder environment.CITATION:Reynolds, B, Olsson, B and Norman, R, 2012. Using independent system simulation to mitigate risk in the Dalrymple Bay Coal Chain, in Proceedings Project Evaluation 2012 , pp 77-84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By P Esteves, J L. Bechir, R Galery, C Senna, V Souto

The current moment experienced by the mineral industry is marked by a series of economic, social and environmental challenges. Among the main challenges, it is important to highlight the decreasing in ore grades with the gradual depletion of the existing deposits, the high volatility in international commodity prices and the operational inefficiencies in the mine, beneficiation, and metallurgical plants. In this context, mining companies are continuously looking for alternatives that minimize production costs and maximize overall production. In addition, recent tragedies involving tailings dam collapses in Brazil, reinforced the need for a more responsible, sustainable, and conscious mining, such as aiming the preservation and rehabilitation of the land environment. In this scenario, the Sensor-Based Sorting (SBS) technology is currently getting more space into the mining market. This separation technology aims the removal of gangue material in coarse particle size fractions, prior to comminution and concentration stages. As a consequence, the technology allows a smaller consumption of energy, water, chemical reagents and other inputs. Moreover, the sensor-based sorting is a dry processing technology and favors the reduction of fine material to be sent to the tailings. The aim of this paper is to provide information regarding the technical and economical evaluation of SBS technology applicability to a zinc silicate mining in Brazil. The project evaluation was performed in two stages: laboratory test work and the execution of a pilot plant. The execution of a pilot plant allowed the technology optimization, quantification of downstream process effects, such as a proper economic evaluation about the technology benefits. Keywords: Sensor-Based Sorting; Particle Sorting; Ore Sorting; Preconcentration; capital expenditure (CAPEX); operating expenditure (OPEX); zinc; comminution; dry processing.

Nov 10, 2020

By I Canbulat, A Mcquillan

This paper presents a parametric analysis showing the impact of virgin in situ stresses on a shallow (less than 100 to 150 m) high slope in a jointed sedimentary rock environment. Slope stability is assessed at varying ratios of slope orientation and horizontal stresses. The results of this study indicate stress conditions should be included in stability assessments of excavated slopes, particularly where structure is orientated perpendicular to the direction of horizontal stress. Some consideration of stress state is applied in deep open cut pits (eg those with planned excavations of 400–1200 m) (Myrvang et al, 1993; Stacey et al, 2003; de Bruyn et al, 2014; Kozyrev et al, 2015). Dodd and Anderson (1972), Kalkani and Piteau (1976), Lee (1978), Coulthard et al (1992), Noorani et al (2011) have studied the effect or horizontal stress and its impact on slope stability, showing that tensile stresses tend to develop at the crest of the slope, with larger tensile zones for higher horizonal stresses and steeper slope angles (Stacey, 1970, 1973; Sjoberg, 2013). However, the consideration of virgin stresses on shallow slope stability is less frequent (Lynch et al, 2005; Dight, 2006; Lucas, 2006; Sjoberg, 2013). This has led many geotechnical engineers to believe the impact of virgin in situ stresses on open cut slope stability is minimal and not worth time or consideration in modelling, or their effects on slope stability are still poorly understood (Stacey et al, 2003; Sjoberg, 2013).

Nov 29, 2022