Search Documents

By W Z. Liu, Q Q. Shi, H T. Yang, X L. Zhang

In order to improve the cutting blasting effect of dimension stone mining, the water coupling directional cutting blasting technology was put forward. Based on the test apparatus and special charge configuration, the mechanism of directional cutting blasting was analysed. Directional device changes the initial equilibrium of the total energy of shock wave effect on blasthole wall. The initial directional crack first appears in the blasthole wall that makes contact with the directional device. Then, two cracks are connected along the direction of the blasthole centre line under the action of detonation pressure and water wedge. The plexiglass tests showed that water coupling directional cutting blasting technology produced cracks along with the predetermined direction completely. The cutting surface was smooth and only a few short cracks appeared around the blastholes. It proved the validity of this technology.CITATION:Liu, W Z, Zhang, X L, Yang, H T and Shi, Q Q, 2015. Directional blasting rock cutting technology, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 815–818 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P Crorkan

Within the framework in which future exploitations for Codelco-Chile Divisi=n El Teniente are situated, regarding the deepening of its reserves and the geotechnical problems that affect their recovery, it becomes strategic to evolve with new variants, which make deep mining possible. Codelco ChileÆs Divisi=n El Teniente is progressing within its long-term planning the exploitation of a sector called Esmeralda, which includes its removal through the gravitational caving method (panel caving). It is planned to use pre-caving, which basically consists of developing and undermining the undercut level, without having developed the infrastructure of the production and transport levels. This is carried out in order to achieve a better redistribution of the stresses, thus obtaining higher quality in the infrastructure development of these levels as well as less risk. The extraction reserves for this area, estimated through the opportunity cost selection criteria, were determined at 348 million tons with an average grade of 1.014 per cent Cu. The project carried out geological and geotechnical studies in order to prevent the geomechanical risks of the sector to be exploited, which is a site conformed totally by primary ore. Lithologically, it occurs mainly in Andesite, located at the western limit by Brecha Braden Pipe. There are also varieties of porphyries and hydrothermal breaches of anhydrite. The Esmeralda Mine production program will increase from 4000 tpd (average) in 1998 to its 45 000 tpd rate of production estimated for the year 2005. The approved investment for the period 1995 to 1999 is $US 150 million, out of a total $US 213 million for the project. At feasibility study level and before the project, it showed a Net Present Value of $US 342 million, an Internal Rate of Return of 37 per cent and an IVAN indicator of 2.3 for a ten per cent discount rate and a copper price of 100 US cents/lb.

Jan 1, 2000

By B G. Blacka, O Salisbury, K W. Mills, R G. Jeffrey

Whitehaven Coal Limited operates an underground longwall mine near Narrabri, New South Wales. The mining horizon in the Hoskissons Seam is overlain by a 16–20 m thick unit known as the Digby Conglomerate, a unit that is sufficiently massive to have potential to cause a windblast during first caving at the start of each longwall panel and periodic weighting throughout the panel. A program of hydraulic fracturing has been successfully used to precondition the conglomerate strata to increase its caveability at the start of each panel. This paper presents a system of temperature monitoring that was used successfully to measure hydraulic fractures at Whitehaven confirming their rate of growth, orientation and interaction with previously placed hydraulic fractures.CITATION:Mills, K W, Blacka, B G, Jeffrey, R G and Salisbury, O, 2014. Temperature monitoring of hydraulic fractures used for preconditioning massive conglomerate strata to reduce windblast, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 189–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By A J. Clough

There has been an unprecedented rise in the fatality rate in the Australian mining industry over the last few years. The factors behind this rise are not clear; however, it is noted that the increase in fatalities has occurred during a fall in commodity prices.This paper examines prevention methods and systems to deal with hazards that have the potential to result in either single or multiple fatalities. Managing the risks associated with mine ventilation is used to illustrate the principals behind the approach.The paper also touches on the broad science of human error and proposes a multifaceted approach to controlling and preventing fatal risks.A summary of the steps involved in developing an effective principal hazard management plan is provided.CITATION:Clough, A J, 2015. Ensuring an effective principal hazard management plan, in Proceedings The Australian Mine Ventilation Conference, pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By T O&apos, Sullivan

Reconciliation of metal production from a sublevel cave (SLC) mining operation is a complicated process. SLC reconciliation is unlike reconciliation for open stope operations, where a tonnage of extracted ore can be assigned to an exact volume of in situ ore, and a direct comparison made between the estimation of contained metal and actual metal production. In SLC operations the ore extracted from a particular SLC drawpoint will be composed in part from the parcel of freshly blasted in situ material, in part from varying components of ore material (from cave stocks) flowing down from other previously mined areas vertically above the current draw position and in part from external dilution. This leads to difficulties in reconciling production grades against estimated grades. The problem is that we know how much metal we have produced but we can not precisely say where it has come from. Metal production reconciliation is fundamental in assessing ore reserve estimation accuracy and performance and in determining a draw management strategy for SLC mining. In terms of contained metal, differences in extracted metal compared to in situ metal represent changes to cave stocks. To generate local estimates of the cave stocks, differences in metal for each ring are treated as additions to or subtractions from a series of vertical columns of stocks extending throughout the height of the cave. The sum of metal differences (extracted versus in situ) for each vertical column results in a residual metal map at any particular mining level. The metal maps show areas where the metal production has been greater than or less than expected. The maps also highlight areas in the cave where residual metal is located, areas where targeted overdraw can reduce cave stocks.

Jan 1, 2006

By P M. Larionov, V I. Zaikovskii

Transmission and scanning electron microscopy together with X-ray spectral microprobe analysis were used to investigate the structure and chemical composition of pathological calcified formations on the bioprostheses of heart valves. Controllable synthesis was carried out under the conditions (T = 37¦C, pH = 7.4) when the ion composition of the main elements (Ca, P, Mg and NaCl) is close to their concentrations in blood plasma. It is proposed on the basis of the obtained results that the formation of the hydroxyapatite of calcific inclusions on bioprostheses occurs as a result of spontaneous precipitation in the blood plasma. One of the factors determining the formation of massive calcified bodies on the bioprostheses of heart valves can be decreased magnesium concentration in blood.

Jan 1, 2008

Lithocaps are potentially voluminous zones of advanced argillic and associated argillic alteration located above the subvolcanic intrusive environment. They constitute exploration objectives for epithermal and porphyry-type deposits. High-sulphidation epithermal deposits may be sought within lithocaps, whereas low-sulphidation deposits may exist on their edges. Porphyry Cu-Au/Au deposits may be accessible beneath lithocaps if systems are telescoped sufficiently. Oxidation of the basal, pyritic parts of lithocaps may promote supergene sulphide enrichment under appropriate tectonic and climatic conditions.

Jan 1, 1995

By Borsaru M, Wylie AW

A neutron irradiation technique has been developed which is suitable for the determinat- ion of the iron and aluminium content of iron ore fines (-6 mm particle size) on a moving rubber conveyor belt. The determination of iron entails measure- ment with a NaI(Tl) gamma ray detector of the characteristic prompt gamma rays (7.64 MeV) due to thermal neutron capture in iron, while the determination of aluminium is based on thermal neutron activation analysis. For the latter a second detector must be placed down- stream to monitor the 1.78 MeV gamma radiation emitted after activation of aluminium. Although conveyor speed has no effect on the Fe measurement, it has an adverse influence on the aluminium signal, and the belt speed should not exceed 0.1 m/s if good accuracy is required. Static trials on a 460 mm rubber conveyor belt with constant ore geometry indicate that for iron an accuracy of ¦ 1.2% Fe (2a) can be achieved for crushed run-of-mine ore at

Jan 1, 1978

The main features and recent developments in the processes of benefication and extractive treatments of tin ores are reviewed. The need for development of processes to recover fine tin, tin from low-grade complex ores and from hard rock resources is indicated. The progress in understanding of slag-metal interactions and developments of fuming processes on industrial scale is delineated. the processes and prospects of hydrometallurgical and chlorination methods are briefly indicated.

Jan 1, 1992

By Marton A

The Readymix Group have a Quarry Improvement Program - 'Building in Quality (BIQ) which has many parallels to the ICI Explosives' total quality management - 'Quality Improvement Program' (QIP). Both companies have for some time recognised that the 'do it right first time' principle means less wasted effort and materials, that efficiency breeds profitability and so actively promote the quality culture. To install the principles and generate the culture requires considerable commitment and effort from the top down and invariably spreads to the suppliers and sub-contractors. Understanding the component processes involved with the quarry operation, analysis of those processes and gaining a breakdown of the cost of non conformance then allows the astute quarry operator to make the necessary changes to improve the process to realise profits. This paper outlines the steps in such a process and the profitable outcomes of the commitment to continuous improvement at the Nickol Bay Quarry.

Jan 1, 1994

By Noller B. N, Mine F. J

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994

A model has been developed for the per iodical maintenance of bins used for hydraulic hoisting in mining of steeply inclining coal seams. This model gives a control plan for hoisting, bin switching and bin maintenance on a regular schedule.

Jan 1, 1977

By M Lak, R Amiri, A Haratian, M Asghari, S Haji

In recent years, due to advances in designing of various magnet assemblies, a wide range of magnetic materials with different properties can be concentrated. Jalal Abad iron ore beneficiation plant, which is located in Iran, Kerman province, is currently producing iron ore concentrate with the capacity of 0.8 Mt/a by having medium intensity magnetic separators (MIMS) with rougher and cleaner stages that finally leads to the production of an iron concentrate with the Fe grade of about 65 per cent. In this plant, the rougher tailings directly goes to the thickener as the final tailings and cleaner tailings feeds to the ball mill for regrinding. Since some hematite particles with weak magnetic properties cannot be recovered from only these two stages of magnetic separation, the obtained tailings from this concentration plant has approximately an iron grade of 25 per cent to 27 per cent. Accordingly, laboratory processing tests were conducted on the obtained representative sample of the final tailings. Based on the experimental results performed on final tailings, a new magnetic drum separator with a specific magnetic assembly was designed that could finally lead to product with iron grade range of 58 per cent to 60 per cent with relative and total weight per cent of 8.6 per cent and 3.86 per cent. Finally, it could be concluded that feeding of magnetite particles to the existing drum separators, due to their high magnetic field intensity, cannot efficiently lead to improvement of the grade of concentrate. Therefore, pilot magnetic separation tests were done on the final concentrate for evaluation of product upgrading probability. Consequently, by increasing another stage of cleaning and by decreasing the magnetic field intensity, the final product grade could be enhanced from 65 per cent to 67 per cent.

Nov 8, 2021

Process engineering principles are used to analyse the features of leaching processes for large masses of low grade, unprocessed ore. Different performance characteristics are related to the numerous variants of these processes. The variant for which reagent enters a heap only via the input solution is further subdivided into three modes of operation. The three modes may occur in testwork and full-scale operations; the effects of process variables on the rate of the process are completely different in each mode. The mode can be identified by the time at which reagent first appears in the pregnant solution. It is related to the ratio of the height of the heap and the thickness of a band of ore in which the reactions are localised. Synthesis of the phenomena occurring within a heap via a computer program has produced a quantitative relation for the reaction band thickness. The program has been validated for several different systems. The overall achievement is that the mode of operation and the rate of the process can be forecast before column testwork is commenced. Some applications of the outcomes to testwork, process design and operational tactics are described.

Jan 1, 1994

By Whiten WJ, Narayanan S

Data from ball mills of a wide range of sizes are analysed using detailed mathematical models and non-linear least squares fitting techniques. This analysis reveals that the relative power inefficiency of large ball mills is due to inefficient grinding of coarse (plus 4 mm) particles in these mills. A qualitative physical hypothesis is proposed to explain this behaviour. The results of the analysis can be used to scale up ball mill behaviour, using the mathematical models and techniques developed. A simpler ball mill scale-up procedure is also proposed, and its limitations stated. Laboratory experiments are being conducted to determine the average size distributions of single particles of different ores after breaKage. These experiments can distinguish between the different ores, and it is hoped to use their results to model and predict the grinding of different ores in ball Mills.

Jan 1, 1978

INDEX OF CONTENTSBlast Furnace SlagsForehearth AccretionsConverter SlagsConclusionsIllustrationsCOMPOSITION OF SOME COPPER SLAGS FROM PORT KEMBLASamples of copper slags from the Port Kembla Smelter of the Electrolytic Refining and Smelting Co. of Australia, Pty. Ltd., have been submitted for mineragraphic examination, with reference to the mode of occurrence of copper in them. The samples included (I) blast furnace slags, (H) a forehearth accretion, and (IH) converter slags. 1. BLAST FURNACE SLAGS Four series of samples of blast furnace slag have been submitted. The. chemical compositions of the several slags are shown in Table 1. Analyses Nos. 1 and 2 are of samples of slowly or normally cooled slag, taken from the slag dump, Analyses Nos. 3 and 4 are of samples comprising slowly or normally cooled slag, together with granulated slag from the same melt.

Jan 1, 1949

By Chitombo G. P, Thompson A. G

Excavation engineering involves three key design processes; excavation design, blast design and reinforcement design. An excavation engineering methodology is proposed in an attempt to promote integration and simultaneous consideration of these three design processes. This methodology requires research and development of, inter alia, a universal rock mass classification system and a universal data display system. Simple examples are used to explain and illustrate the concepts central to these components in the three design processes.

Jan 1, 1995

By Lemberg D. W, Friday R. G

Potential means of lowering overall costs to permit deeper stripping include : 1. the use of larger diameter blastholes in highly-fissured strata (to reduce drilling costs); 2. dewatering from semi-permanent bores to reduce blasting costs (by maximising the use of bulk ANFO) and promote highwall stability; and 3. the use of inclined blastholes, bulk AN, staggered V1 patterns, adequate backfill and more cost-effective stemming columns. Each of these is covered. The pumping of bulk watergels continuously raises the blasthole water column, thereby perpetuating the demand for these blasting agents. This must be a principal consideration when choosing between a bulk and a packaged watergel. Any packaged product should exhibit dimensional permanence and an energy yield per metre length equal to that of bulk ANFO. Possible ways in which controlled trajectory blasting (CTB) could benefit deeper stripping operations are outlined. By allowing the maximum use of bulk ANFO, de- watering may be a prerequisite of a viable CTB Operation.

Jan 1, 1981

By Chaturvedula V. K

Pillar extraction carried out using various methods (split and lift, Wongawilli and Old Ben) involves the formation of narrow fenders (commonly 7 m of coal) formed by driving "splits" for lifting off with a continuous miner. The strata above a split and fender adjacent to the goaf consists of a cantilever beam (usually >3 m thick) that extends from the solid coal and bridges across the fender. Lifting off the fender from the split in safe conditions depends upon the bridging capability of the cantilever and the fender strength. The nature and competence of the immediate and near roof, the support capability of the coal fender and the presence of faults and or joints can adversely affect the bridging behaviour of the cantilever. Insufficient knowledge of these parameters can lead to extraction under dangerous conditions. Remnants of fenders ("stooks") also support the cantilever and their dimensions are critical to obtain regular caving and goaf falls. Stook area, goaf roof span and roof stand-up time after lifting can be related and only a relatively small increase in stook area of 10-15 m2 can lead to a significantly increased stand-up time, especially under a massive roof. Such conditions strongly influence the re- distribution of abutment stresses and can create increased outbye pillar loading. Based on detailed underground geotechnical investigations, it is concluded that strata caveability, roof cantilever behaviour, fender H:W ratio and remnant stook size are all critical parameters for successful and safe pillar extraction.

Jan 1, 1992

By T Kitajima, T Kawaguchi, T Nakamura

Carbothermic reduction of iron oxide is an attractive mechanism to produce metallic iron, since it can directly utilise coal as both reductant and fuel. To improve energy efficiency and productivity of the metallic iron production based on this mechanism, the combustion bed process packed with the composites of iron oxide and coal powder was experimentally evaluated. The process has a potential of high heat efficiency since it can automatically utilise the heat of reduced materials as that necessary to the subsequent reduction of the composite by a large heat exchange rate between the packed particles and gas flowed across the bed. However, it is hard to perfectly prevent the reoxidation of formed metallic iron in the bed. The present paper reports the effect of coal content, pellet size and so forth on the reduction/metallisation degrees of the samples after the reduction experiment. It also discusses the effect of pretreatment of the composite pellets using CaO bearing materials to suppress the reoxidation of formed metallic iron in the bed.

Jan 1, 2000