Search Documents

By E P. O’Dwyer

Segment and gasket lining in tunnel boring machine (TBM) tunnels; and sheet membrane lining systems in driven tunnels are robust waterproofing systems each with a proven history of performance in Australia and further afield. Where an interface between these two systems occurs, the potential for costly failures is vastly increased and additional attention to detail is required in design, planning and construction. TBM cross-passages represent the most common occurrence of this interface, with steel compression flanges and neoprene gaskets being the typical means of connecting the waterproofing systems. There is a large variance in both detailing these flanges and associated outcomes, which makes this an area where there is room for improvement within the industry.The paper will look to tease out the various issues associated with this interface and how they can be dealt with efficiently with appropriate design measures, robust planning and carefully controlled construction methods.The paper will also look to review the new technologies and systems currently being put forward as potential alternatives, including an epoxy tape system, which has recently been successfully trialled on a project in Europe under high-pressure head.CITATION:O’Dwyer, E P, 2014. The challenge of waterproofing cross passages in segmentally lined tunnel boring machine tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 315–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By R J. Wood

Raise drilling (or raise boring) is not a new technology or methodology. The first raise drilling machine was developed by The Robbins Company (TRC) of the USA in 1962. TRC manufactured the first tunnel boring machine (TBM) in 1952 and Jim Robbins, the founder of the company wanted to ‘turn the TBM concept on its head’ so to speak.Many improvements have ensued in the 50 years since the first machine. Such improvements include advances in the drill rod and thread design, cutters and reaming heads. Raise boring would not have been possible without the development of the tungsten carbide insert cutters and there have been big advances in both the carbide technology and in the mechanical design of the cutters.Over time mines have developed deeper with a greater use of diesel equipment resulting in greater ventilation requirements. This in turn means larger and deeper ventilation shafts. There have also been improvements in directional drilling techniques. This all combines with the need and ability to construct larger shafts using the safe method of raise drilling. With suitable geotechnical conditions the RBR900VF is capable of drilling shafts to a diameter and depth of greater than 8 m and 2000 m respectively. Greater diameters are possible over shorter lengths with suitable ground conditions.The RBR900VF was designed and manufactured to specifications developed by Macmahon. This machine has the greatest thrust and torque capability of any machine in the world. It enables cutters to be more heavily loaded in the larger diameter heads and this is essential for efficient rock excavation. Additional features of the new machine include minimal manual handling to provide a safer working environment and higher strength steel for the drill rods providing additional safety margin.CITATION:Wood, R J, 2014. A revolution in raise boring – the development of the RBR900VF, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 171–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By R Talebi

A research project to better understand the rock mass behaviour and the seismic response has been conducted during the design and construction of the 9215 level at the E-Block sector of the Northern Star Kanowna Belle Mine. The research program was undertaken at a tunnel located 1100 m below the surface with the results applicable to feasibility studies on underground mining projects in highstress conditions, where failure can occur very soon after tunnel construction. Semi-circular excavation shapes coupled with the use of de-stress blasting techniques were designed to monitor the excavation in conditions of very high stress. The ground support was designed considering high energy dissipation ground support schemes (HED) as described by Arcaro et al (2021). The results indicate a decreased rock mass demand due to the change of excavation shape. Also, localised reduction in rock mass stiffness was achieved due to the implementation of de-stress blasting. Finally, increased ground support capacity was gained by the implementation of the high energy dissipation ground support schemes. The Kanowna Belle Mine has significant ore reserves at depths exceeding 1000 m below the surface. The results of this research will be used to optimise the extraction of the remaining E Stoping Block at depths exceeding 1350 m.

Mar 29, 2023

By Romanovsky N. P

The Pacific Mobile Belt (PMB) is characterized by old origin and complex evolution both in time and space. As the global structure, the PMB is a narrow tectonic region dividing two plan-etary hemispheres, viz. the Pacific and IndoAfro-Atlantic ones, the relative shifting of which defines the character of many geodynamic processes in this belt. The PMB features inhomogeneity of structure, special matter composition characteristics, sharply broken-out topography, and intensive fields. Generalized anomalies of the gravitational field closely correspond to the PMB boundaries defined by the real features, i.e. the andesite line and distribution areals of Mesozoic-Cenosoic granitoids. The belt boundary position is controlled also by seismic velocity anomalies at a depth of down to 200 km. The modern PMB deformation is defined by the left-hand equatorial shift and rotation of the Pacific Ocean counterclockwise. This rotation is non-uniform in time and of an oscillating character. The motive forces of the phenomenon are considered.

Jan 1, 1990

By Pratt V, Davis K

Challenges facing middle management in the 1980's and beyond are not confined to business matters such as industrial relations, government and legal constraints, corporate takeovers, and commodity marketing. More particularly they deal with people issues and the interrelationship of corporate/ family relationships. There is a need for corporations to acknowledge the growing conflict between corporate/family roles being brought about by such matters as equal opportunity, double professional marriage partnerships, personal mobility and the increasing stress faced by managers as a result of current demands and expectations being placed on them. While the main responsibility for managing professional life as well as the relationship between professional and private life rests with the individual executive, corporations nevertheless have a major responsibility to assist these executives in this management process. Corporations in Australia are taking steps to address this situation but much more needs to be done. This was highlighted in the March 1985 "Middle Management" course with its associated Spouses Programme presented jointly by Australian Mineral Foundation and The Australian Administrative Staff College. Effective communication is at the heart of the matter but no amount of training on this subject will bear fruit unless there is an associated commitment by executives to improve the effectiveness of their communi- cation process both in their corporate and family roles.

Jan 1, 1986

By Wong KY, Woodcock JT

Previous results have shown how con- trolled-potential sulphidization (CPS) can give improved metallurgy during rougher flo- tation of mixed oxide-sulphide copper ores. Results in this paper, using different samples and different equipment, confirm the previous results and extend the application of CPS to cleaner flotation. By using CPS, faster flotation of copper minerals (chalcocite and malachite) from clay was obtained in roughing and cleaning, and improved concentrate grades and recoveries were achieved over those by conventional manual control. The optimum sulphidizing potential (i.e. the potential of a sulphide ion-selective electrode versus a saturated calomel electrode) was -500 mV, and could be controlled to ¦5 mV, during four rougher- scavenger and three cleaner-re cleaner stages. This optimum gives the best balance between copper recovery, concentrate grade, and sodium sulphide consumption. Five cleaning circuits and five ore com- posites of different composition (0.55-1.50 per cent Cu) were examined as well as the effect of feed size and pulp density. Better results were obtained at 20 per cent solids in a Denver cell than at 33 per cent solids in an Agitair cell; this may have been related to the high clay content of the ore. Commercial equipment for pilot plant or full-scale plant application of CPS is cur- rently being developed.

Jan 1, 1986

By Drew GJ

Smelting is a process in which heat is applied to ores to produce metals. Impurities are removed by segregation in the slag, or converted to gases or sublimates and discharged up the flues. Mate- rials delivered into the smelter have generally been previously concentrated or processed at the mine, and the size of their particles, and also their chem- ical composition, greatly affect the smelting proc- ess. Some impurities are more difficult to remove than others, and are more objectionable in the finished product. The first metal mine in Australia was opened near Glen Osmond in South Australia in 1841, for silver-lead ore. It was followed by the Kapunda Mine for copper in 1844 and by the very signifi- cant Burra Mine, also for copper, in 1845 (Figure 1). A major part of their ores could not be exported profitably for smelting in England and Wales where the large smelters were then located. In addition to treating ores from Cornwall these also smelted ores from recently opened mines in Cuba, Chile, and Mexico. The Welsh smelting process (Figure 2) was developed over a period of years to utilise Welsh coal to treat copper ores particularly from Corn- wall. The first step consisted of a calcination to remove sufficient sulphur from sulphide ores so that subsequent melting operations would produce copper matte, a copper-iron-sulphide which melted at about 1050¦C. Subsequently refined to white metal with the addition of carbonate and oxide ores when these were available, and often through an intermediate step of blue metal, this matte was finally oxidised to pure copper, or as pure as it could be made in those days. The movement of metal towards greater purity was matched by a reverse flow of slag, carrying reducing quantities of copper, so that the slag rejected from the first melting process carried the minimum quantity of copper. Chemical analysis was virtually unknown. Materials were assayed in the laboratory by a small scale smelting process, and the purity of the final refined copper was judged b} the ease with Mhich it could be hammered into thin sheets.

Jan 1, 1987

By Petersen V, Potke W, Polthier K

The paper reviews some of the aerodynamic factors in the blast furnace process and outlines the areas requiring further study. Detailed discussion is given to the pressure drop in both the dry and the wet zone of the furnace and an optimum coke size is suggested for minimum pressure drop. The effect of various charging sequences on the distribution of the gas in the furnace shaft is treated and notes on stack injection included. Flow phenomena limiting blast furnace output and the influence of aerodynamics on the movement of the bed in the furnace are outlined and these include fluidisation, flooding and raceway formation. A mention is made of alkalis, sulphur, zinc, softening, and oil injection and the mixed effect in blast furnace economics of increased tuyere velocity as problems requiring further research.

Jan 1, 1975

Base metal skarns have provided most of South KoreaÆs Pb-Zn production since the end of the Korean War, with the bulk of production coming from the Yeonwha group of mines. Currently only the Kumho Zn-Pb mine remains in production, while magnetite skarns are mined as iron ore at the old Yomisan and Ulsan base metal deposits. Base metal skarns within Korea fall into two groups; those hosted in Cambro-Ordovician limestone sequences, situated mainly in sub-basins in the northeast of the peninsula and those hosted within carbonate volcaniclastics of the Cretaceous Gyeongsang Basin, in the southeast. Sulphide mineralisation is dominated by sphalerite, lesser galena, arsenopyrite and pyrrhotite, with subordinate chalcopyrite and molybdenite with Ag-Co credits. Skarns are composed of pyroxene-clinopyroxene-garnet-carbonate-quartz and magnetite, grading into silica-chlorite hornfels. Most of the significant deposits display both pipe-like and stratabound morphology. In the Hwanggang district, a zoned distribution of Ordovician carbonate hosted, polymetallic Mo-W and Zn-Pb-Cu-Ag base metal deposits is observed around the margin of a Cretaceous granite intrusion. Similar polymetallic zoning is recognised in the Sangdong district, where deposits include Sangdong (W), Abisan (Au-As) and Yomisan Northwest (Zn-Mo) and Yomisan Southeast (Zn-Cu-Co), hosted in Ordovician carbonates in proximity to Cretaceous quartz porphyry intrusives. The Taebaeksan district hosts the largest deposits at the Yeonwha group of mines. Although production ceased in 1993, significant resources remain, hosted in Ordovician limestone and dolomite that have been intruded by Cretaceous quartz porphyry dykes. Deposits in the Cretaceous Gyeongsang Basin consist of bedding concordant, vertically stacked base metal skarn mineralisation at several stratigraphic horizons, connected by carbonate-base metal veins with a pipe-like geometry. Evidence such as massive sulphide layers and restricted proximal carbonates suggest mineralisation was initially partly syn-depositional, with both base metals and carbonate venting onto a lake floor, being reconstituted to skarns by later magmatic activity. Skarn mineralisation is universally closely associated with the Cretaceous Bulgugsa Series acid intrusive activity. A common intrusive-structural relationship is recognised at some deposits, with bedding plane and imbricate thrust faulting, introducing felsic intrusives as sills. These intrusions probably introduced the base metals, carbonate, boron, heat and silica, which metasomatically reconstituted the carbonate lithologies to form skarn assemblages. The Korean base metal skarn deposits are regarded as Zn-Pb chimney-manto skarns and display similarities to the Mexican manto type deposits.

Jan 1, 1999

ATTENTION has recently been directed to the subject of dust production and methods of allaying same in the Broken Hill mines, so that the time would seem opportune for the local branch of the Institute to discuss certain features of an important phase of the health question in connection with underground work. Tests conducted in the Broken Hill South mine and at other mines at Broken Hill have shown that the ordinary operatioils of mining, such as boring, blasting, and shovelling, may be accompanied by the production of considerable dust unless water is judiciously used.In South Africa·dust particles under 5 microns size are regarded as dangerous, becailse they are so small as to be invisible to the naked eye, and wm esc'ape the protections set up by nature in the nose and throat, and thus may be inhaled in large quantity. A micron is 1 25000th part of an inch. This paper contains an account of the work done on the Broken Hill South mine chiefly, though some tests were done on other local mines.An acknowledgment is due to Mr. T. A. Reid, of the Broken Hill South mine, who conducted some of the tests herein mentioned, and under whose supervision most dust counts were made. Numerous dust samples have been taken by means of thekonimeter, an instrument designed by Dr. Kotze, the Government mining engineer of the Union of South Africa, and fully described...

Jan 1, 1921

By P Bourke, S Ronkainen

Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technicianÆs job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always other problems to attend to. A considerable amount of work has thus been done to develop a æsystemÆ that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterÖ instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability. Three FrothMasterÖ units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:to control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other; control of the concentrate grade (per cent copper) from the first rougher; reduction in the frother consumption in the rougher circuit by monitoring the froth speed. A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions: Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint. Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time by the OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore. The results from a 21-day trial have shown the following:The ratio of concentrate mass-recovery between two cells in series on the same level has been successfully balanced, thereby overcoming problems due to differences in hydrostatic heads. It is possible to control the speed of the froth, in mm/s, to within five per cent of its setpoint using the aforementioned manipulated variables. It has also been shown that, for reliable control, it is necessary to control more than just one variable (eg level or air). The grade of the first rougher concentrate has been controlled to within 0.3 per cent of the grade setpoint for long periods of time, which has important implications for the circuit recovery. The frother consumption has been reduced significantly. This paper will thus show that substantial progress has been made to demonstrate the value of using on-line froth speed measurements in flotation plant control to obtain real financial benefits.

Jan 1, 2000

By Green A. D M

The establishment of the Imperial Smelting Furnace at Sulphide Coporation Pty. Limited for the smelting of zinc and lead made it necessary to design and install sintering capacity to produce approximately 500 t.p.d. of zinc-lead sinter. The updraught sintering process installed is a recent development and the plant was designed with adequate flexibility and equipment to enable operating staff to investigate the process and achieve maximum production under optimum operating conditions.Sulphur dioxide gases from the sinter machine are passed to a contact acid plant for the manufacture of sulphuric acid.

Jan 1, 1964

By Andersen AK

As part of a research program sponsored by Continental Copper and Steel Industries, Inc. (cos), investigations have been conducted by the Colorado School of Mines Research Foundation, Inc. to study the effect of high current densities on electrolytic processes. The importance of high current densities has long been recognized, particularly in the deposition of copper, and the results of considerable research on the subject have been reported in recent years (19 29 39). This is not surprising because, besides plant capacity, current density is the other major factor which will determine the process economics. In the production of electrolytic copper, current efficiency, steam consumption, number of cells, building area, metal inventory, cathode purity, and power consumption are all affected by current density. The ability to maintain a high current efficiency and satisfactory cathode purity while increasing the current density to twice or three times that commonly practiced could result in considerable saving of capital investment and reduce the operating cost per ton of metal produced. The optimum current density i.e., that current density of which production cost would be at a minimum, can be established from an analysis of the various inter- relating factors (49 59). A review of.all operating electrolytic plants (electrowinning and electrorefining) will indicate that most of these plants are operating at 50% or less of the optimum current density (6). One of the reasons for not using the optimum current density may be attributed to the fact that conventional electrolytic tank- house equipment does not perform satisfactorily at high current density operations. Various investigators (19 79 8) have attempted to overcome this limitation by modifying the design of the electrolytic cell, virtually unchanged since it was first introduced in the late 1800's. Previously, these attempts have not resulted in,a cell design suitable for commercial application. However, recently, a cell has been designed which performs efficiently under such conditions. This is a CCS development (patents applied for).

Jan 1, 1969

By Morley C

The Mount Charlotte gold mine is located 0.75 km east of the General Post Office in Hannan Street, Kalgoorlie WA and about 3.5 km north of the Fimiston Operations on the famous Golden Mile.Mechanised underground bulk-mining at Mount Charlotte has been in continuous operation since 1963. For the 30-year period ending December 1992, the mine produced 22 million tonnes (Mt) of ore for a recovery of 2.73 million ounces. During 1991/92, the mine produced 1.53 Mt of ore at a head grade of 3.15 gramshonne (g/t) for a recovery of 135 822 ounces.The principal ore source at Mount Charlotte has been the Charlotte Orebody which is now largely mined out. Since 1990, approximately 75 per cent of production has been sourced from the Reward Orebodies. The Charlotte Orebody was a relatively homogeneous quartz stockwork with simple geometry and average bulked grades in the range of 4.0 to 5.5 g/t. This is in contrast to the Reward Orebodies and the more recently defined Charlotte Deeps and Maritana Stockworks, which have complex grade distribution and geometry with lower average bulked grades (2 to 4 g/t). The lower grades are principally due to the decreased density and volume of stockwork venation and related vein halo alteration. Typically, these stockworks comprise a patchy mosaic of quartz veins and vein swarms, with irregular distribution and geometry within the quartz gabbro host rock.

Jan 1, 1993

By Wightman D, Hoyle M. W H, Peters W. S

The Radio Hill nickel-copper deposit is located 30 km south of Karratha. It is a new discovery in an area where similar mineralization had been previously discovered at Mt. Scholl and Ruth Well. Radio Hill is the first massive Ni-Cu sulphide deposit of economic significance to have been located in the Western Pilbara.Preliminary studies indicate that the sulphide mineralization occurs within gabbros, pyroxenites and peridotites of a basic igneous cumulate layered sequence. Primary sulphides have been subsequently remobilized and concentrated as stringer and massive mineralization. This is tentatively attributed to the intrusion of a further gabbroic body.The deposit appears to be of the gabbroic association type with a Ni:Cu ratio varying from 1:4 in the outer parts of the mineralized envelope to 1:0.9 towards the central zones. In drill core observations, chalcopyrite surrounding pyrrhotite was noted in many instances. Drilling has so far delineated a body developed over a strike length of 600 m and a horizontal width of up to 25 m. The mineralization plunges 20° to the southwest with a southerly dip varying from 75° in the west to about 20° - 30° in the east.The deposit is a leaf-shaped ore zone, plunging southwest from a vertical depth of 17 m in the north to 300 m in the south. The massive sulphides occur as lensoid masses within this zone. A geological resource of up to 2.5 million tonnes at 1.5 per cent Ni and l.4 per cent Cu is indicated.The predominant sulphides are pyrrhotite, chalcopyrite and pentlandite, with significant cobalt, platinum group metals and gold. Tellurides of Pd, Bi and Pb were detected by scanning electron microprobe within the pyrrhotite and other trace metals include Zn and native tin. Massive magnetite is sometimes associated with the massive pyrrhotite intersections.A test on one composite massive sulphide sample showed that pyrrhotite is present mainly as the non-magnetic hexagonal variety and only 10 per cent is present as magnetic monoclinic pyrrhotite.The deposit has no surface expression and its identification was based mainly Oil drilling targets generated by geophysical methods. No secondary minerals have been observed in association with the primary sulphides, even though the deposit is only 17 m below surface in the northern part.

Jan 1, 1987

By Rose CW

Typical rehabilitation programmes for spoil piles and waste dumps in open cut coal mines involve the spreading of topsoil to assist vegetation growth. In the early years of rehabilitation before a protective vegetation cover has been established, this topsoil is susceptible to erosion during rainfall events. Since the long term success of rehabil- itation procedures is sensitive to adequate topsoil maintenance and since, on many mine sites, topsoil is a scarce resource, erosion losses of topsoil (particularly once fert- ilised) can severely restrict rehabilitation Measures.

Jan 1, 1983

By Frew J. A, Harris M. C, Manlapig E. V

The recovery achieved in a flotation process is a function of both the characteristics of the feed stream and the operating conditions within the flotation cell. In this paper, the flotation characteristics of the streams within the Red Dog le

Jan 1, 1997

By Z W. Orndorff

Excavation through sulfidic geologic materials during construction activities has resulted in acid rock drainage (ARD) related problems at numerous (>40) locations across all five geologic regions of Virginia, USA. Potential acidities ranging from >100 to develop a statewide sulfidic materials risk map; document ARD impacts to soil and water quality and engineered structures; and develop methods to assess site-specific risk potentials within a given highway corridor. A statewide sulfidic materials GIS risk map was developed based upon the state digital geology map which assigned four levels of relative risk to all mapped strata based upon predicted lime requirements and probabilities of encountering highly reactive materials. Non-highway construction activities have also routinely disturbed sulfidic materials, and a recent airport project in northern Virginia resulted in over 150 ha of extremely acidic (pH 45 mg/L) run-off from this site heavily damaged a receiving stream, partially due to the fact that it dissolved the galvanised steel water control structures in stormwater detention basins, leading to direct discharge of run-off and sulfidic sediments. The airport area was treated and revegetated in 2002 with a combination of lime-stabilised biosolids, straw mulch, and acid-tolerant grasses. Water quality in a receiving second-order stream quickly responded to the treatment, but some release of N was also noted as a secondary effect. Collectively, these results point out the importance of accurately assessing the potential for excavation of sulfidic materials in construction environments, and the necessity of developing toxic materials handling strategies similar to those employed in mining environments.

Jan 1, 2003

By Koppe JC, Strieder AJ

The Rivera Crystalline Island (RCI) is an erosional window of the intracontinental Parana Basin that outcrops in the Rivera Department, north of Uruguay. RCI is made up mainly by Precambrian granites, metasediments and granite-gneisses. This island is crosscut by a dextral transcurrent shear zone system, the Rivera Shear System (RSS). The bulk strain ellipsoid was defined by previous work and has allowed the evaluation of shear dynamics. The geometry of the shear system is made up of two shear directions: E-W (P-shear), which turn right to NW-SE direction (R-shear), leading to the development of extensional bends. The shear zone system was developed in brittle-ductile to brittle regimes, under temperature conditions compatible with greenschist facies metamorphism. The shear zones are marked by an intensive fracture cleavage development. Mylonites develop only in narrow, discontinuous higher strain zones. Internally, the shear zones are dominated by intrusive rocks, mainly granites, dacites and diorites. Hydrothermal alteration has been developed in several areas.The economic significance of RCI is given by several small gold deposits, which have been exploited since 1869. One major new gold mine is under development, the San Gregorio Gold Mine. This gold deposit is locally controlled by a dilatant site where R-shear turns right to P-shear. Mine lithologies were deeply altered by hydrothermal fluids in the dilatant structure. This work presents the lineament-structural analysis carried out to identify similar structural patterns in all RCI sites favourable to host other gold deposits. The exploration program also considered remote sensing, geology, geophysical and geochemical survey.

Jan 1, 1997

By A M. van Niekerk, W Mey

Coal mining has an impact on the water management of the water scarce Upper Olifants River Catchment. A prefeasibility study was carried out by Anglo Coal and Ingwe Collieries Limited to establish the water supply and demand in the catchment. A geohydrological model was used for the coalfields to determine the stored water and excess water available. Two distinct collective and treatment systems were proposed for the Witbank and Middelburg municipalities to treat excess water from the Anglo Coal and Ingwe Collieries Limited. The Emalahleni Water Reclamation Project for Witbank was initiated first. Water management and treatment experience gained at Anglo Coal was the cornerstone to develop the collection, treatment and distribution system. A full enquiry was issued to Keyplan, Veolia, Bateman Africa and IST Technik to construct, commission, operate and maintain a 20 ML/day desalination plant to treat acidic, saline mine waters to a South African National Standard (SANS) 0241 Class 0 potable water. After the technical and financial adjudication, Keyplan were awarded the contract. An integrated regulatory process was adopted through consultation with all the relevant regional and head office staff of the Department of Minerals and Energy, Department of Water Affairs and Forestry and the Mpumalanga Department of Land Affairs via an authorityÆs steering committee. A rock engineering evaluation was done to select both the plant and waste disposal sites as all possible sites are undermined. Various contracts are required with the individual mines for water supply, the Emalahleni Local Municipality for the delivery of potable water and for the disposal of wastes.

Jan 1, 2006