Search Documents

By Higuchi K

In this paper, the history of Japanese coal and gas outbursts is presented and circumstances and countermeasures at the time cf outbursts are summarized statistically. Then the present meth- ods for prevention used practically in Japan are introduced. From statistics, it was reconfirmed that Japanese coal and gas outbursts have occur- ed frequently in the district of geological disturbance, symptoms immediately before out- burst occurrence were the phenomena in connec- tion with failure of a coal seam and outbursts have occurred many times when the number of boreholes had not been sufficient to degas. One of the principal protective method adopted in Japan is the large diameter gas drainage boring which also posesses a stress relief effects. There is a tendency to make diameter of borehole larger to increase both stress relief and degassing effects.

Jan 1, 1986

By A Giyose, V Malysiak, K Davey

Batch flotation tests were conducted on a haematite-bearing Sishen iron ore slimes sample from South Africa using reverse cationic flotation. The effect of grinding on flotation performance, the flotation response of various key impurities in the sample, and the feasibility of increasing metal recovery by refloating tailings in a scavenger flotation step were investigated. The test results indicate that reverse cationic flotation is effective in rejecting impurities from the iron ore sample tested. From a head grade assaying 6.4 per cent SiO2, 2.14 per cent Al2O3, 0.402 per cent K2O, 0.082 per cent P and 0.194 per cent TiO2, the levels of impurities were reduced to 1.83 per cent SiO2, 0.88 per cent Al2O3, 0.095 per cent K2O, 0.066 per cent P and 0.174 per cent TiO2 in the final concentrate at a Fe recovery of 74 per cent. The flotation response of SiO2, Al2O3 and K2O were found to be better than that of P and TiO2. The testwork demonstrated that grinding to 80 per cent passing about 49 microns is essential for upgrading the Sishen iron ore to produce >67 per cent Fe concentrate grade. This grind size corresponds to about 80 per cent liberation of haematite from the gangue minerals. Fe recoveries up to 76 per cent were obtained by refloating the rougher tailings in a scavenger stage, with little effect on the final concentrate grade. Size-by-size Fe recovery data obtained indicated that particles below ten microns were mostly lost in the desliming stage conducted prior to flotation whilst some reported to the froth by entrainment. Some of the coarser haematite-gangue composite particles reported to the froth product by genuine flotation.

Jan 1, 2009

By A Kondratiev, A E. Moiseev

Viscosity of oxide melts is one of the fundamental physicochemical properties that plays a crucial role in important technological and natural processes like slag flow, slag/metal separation, volcano eruptions etc. However, many oxides melt at extremely high temperatures and are highly corrosive in the liquid state, which makes experimental measurement of melt viscosity by traditional experimental techniques a difficult and expensive, if not unachievable, task. In this case it might be useful to employ other methods of viscosity determination such as modelling or simulation. In the present paper the shear viscosity coefficients of selected pure refractory oxides (CaO, MgO, Al2O3 and others) have been simulated at temperatures above their melting points via the classical molecular dynamics and compared to the available viscosity data (eg experimental viscosities, other model predictions) collected by the authors. The simulation has been carried out using the noncommercial molecular dynamics simulation package LAMMPS and the Born-Mayer-Huggins potential, which parameters for the selected oxides were taken from the literature. Several viscosity calculation techniques (the Stokes-Einstein and Green-Kubo equations, the so called Einstein relations, and the non-equilibrium molecular dynamics methods) have been applied to ensure a more reliable viscosity calculation. It has been demonstrated that the simulated viscosity of the selected melts agrees with the available experimental data. It has also been shown that the simulated viscosity of a number of the oxide melts investigated is close to that calculated by phenomenological viscosity models, which supports viscosity extrapolation from the corresponding binaries and ternaries, if no experimental data is present for unary systems. In general, it has been demonstrated that the molecular dynamics simulation could provide a reasonable estimation of viscosity if no other viscosity data is available.

Jun 19, 2024

By McKenzie C. K, Stewart R. S, Simpson J

Blast control in small scale underground mining leads to improved fragmentation control, improved control over overbreak and dilution, and the optimisation of drilling and charging operations. Greatly improved control can be achieved through blast monitoring, to confirm proper implementation of blast designs and blasthole charging. Further improvements can be achieved through simple modelling, enabling blastholes to be placed in the correct locations and charged with the correct weight and strength of explosive. Improved design can be shown to significantly reduce overbreak and dilution, and even ground support costs. In one mine in Quebec, open stopes of widths varying from 2.5 metres to four metres and dipping at 36¦ to 38¦ were designed to achieve zero dilution using open sloping blasting practices. The first stope designed in this manner was monitored in detail and achieved its objective.A method for contouring damage around blastholes is presented as a basis for selection of drilling patterns, with particular application to the control of overbreak and dilution. Contouring can be used to provide reliable estimates of either overbreak or damage (where rock is broken het reynainc in nlarr)

Jan 1, 1993

By Cocker J, Urosevic M

Seismic methods have become common for the detection of low-throw faults ahead of underground coal mining. Surface seismic methods cannot theoretically be used where dykes occur, because seismic waves transmit from the surface down to the seams, and reflect back to the surface. Consequently, where sub-vertical structure such as dykes occurs, the surface seismic method fails.The ability of seismic methods to image dykes depends on the geometry used, the dyke thickness and the seismic wave propagation mode in relation to dyke composition and internal structure. Surface seismic methods find it difficult to distinguish between faults/fractures and very thin dykes (1-2m in thickness) when the dyke's thickness is less than the seismic wavelength. Consequently, borehole seismic methods have to be used to detect the presence of such thin dykes.

Jan 1, 1998

By Hsiung SM, Jiang YM

The orientation and location of the hydraulic legs are two very important parameters for the design of shield supports in longwall mining. Studies have shown that leg orientations and locations of a support determine the magnitude, orientation and location of the resultant support resistance which in turn affects the efficiency of the support and the ability to prevent premature roof falls in the face area. Therefore, there is a need to determine the best combination of orientation and location of the hydraulic legs for each type of shield support under various geological conditions. This paper attempts to evaluate, first, the individual role of each parameter (orientation or location) and then to determine their integrating functions in terms of ground control employing finite element analysis. Three types of shield support (2-leg and 4-leg shields and 4-leg chock shield) with various combination of the parameters are simulated and their effects are discussed. The optimum design for each parameter for each support type under various geological conditions is also discussed and recommended.

Jan 1, 1988

By J Boland

Polycrystalline diamond compacts (PDC) have been widely used as cutting elements in the drilling tools for the oil, gas, civil and mining industries because of their faster penetration rates and longer bit life. US Department of Energy reports that PDC bits account for more than one-third of the total footage drilled worldwide (US Department of Energy, 2004). However, non-thermally-stable diamond composites (NTSDC) have seldom been applied to geothermal drilling, since premature failures of such PDC cutters have been observed in hard rock formations. Several factors need to be considered to prevent premature failure of cutters and improve cutting performance when using PDC-based bits and other rock cutting tools. The first set of factors consists of the strength, density, stiffness, toughness and thermal resistance of the PDC and the rock. A second set relates to the complex behaviour of the bonding between the PDC cutter and the bit matrix, or the pick and the pick holder, which is vital in maintaining stable, reliable and durable adhesion of the cutters to their hubs. Finally, based on a better understanding of the cutting processes, the formulation of a predictive model would assist in further development of cutter design.

Jan 1, 2004

By Huntington J. F, Green A. A

The quality of a photointerpreter's anno- tation of an image may be displayed by writing maps in which the pixels are shaded according to the number of times a pixel was seen to be on a feature. The map of grey tones is more valuable, if, for each grey level, a measure of quality is determined, which is the probability that a feature exists in a pixel of a given grey tone. From repeated annotations (at least four) of the same image by a single observer, it is possible to formulate a perception model which describes stochastic processes in the observer. From that model, it is possible to assign estimates of data quality for each observer to each grey tone. For two observers on the same scene, the 'mean' method of quantifying the grey levels is to assign a value equal to the mean of the ii,:lities for each of the two observers separately. For this example, the grey tones arr thus quantified at probability levels of 0.70, 0.80, 0.90 and 0.95.

Jan 1, 1977

By Nevolina VG, Zakharova IB

The results of a study on the flotation of baddeleyite and associate minerals are presented, together with effective flotation reagents. Detailed microcrystallomorphological analysis of the benefication products were made to find out the features of distribution of different baddeleyite generations between froth and chamber products. To reveal the dynamics of interaction of technological properties of minerals with their morphology and constitution, a method of onthogenetic analysis was used. It is well known that the difference between technological properties of the particles of the same mineral depend greatly on its genesis, but also the relation is direct - by means of constitution (habit). Thus, flotation behaviour of minerals depends on morphology microinclusions, distribution of impurities, dislocations and physical properties of individual particles. The microrelief of baddeleyite grains and crystals from froth and chamber products was studied with an electron scanning microscope. Chemical composition was determined by means of laser, microprobe and chemical analyses. The difference between baddeleyite generations, their distribution in benefication products, and the effects of grain sizes, number of inclusions and chemical compositions were valuated. Conclusions on baddeleyite flotation properties were made. Mineralogical study on eudialite grains from rough ore and eudialite concentrate was carried out. The interrelation between eudialite and associate minerals and negative effect of aegirine on technological properties of eudialite were revealed as well.

Jan 1, 1993

By Sen A. K

The Chiria Iron Ore deposit falls within the well-known Horse-shoe-shaped Singhbhum-Bonai-Keonjhar belt in India, where most of the deposits supplying ore to various steel works of Steel Authority of India Limited (SAIL) and Tata Iron and Steel Company (TISCO) are located. With an estimated reserve of about 2000 million tonnes of ore (at 55 per cent Fe cut-off) spread over four contiguous blocks, it is the largest iron ore deposit in India and one of the largest in world. The present study is confined to only one of the four blocks of Chiria viz North Block, comprising an area of 2.11 km2. `Corporate Plan 2005' of SAIL envisages development of a large open cast mine at Chiria to meet its enhanced requirement of iron ore by 2001-02 AD.

Jan 1, 1995

By K Williams, A Lavrinec, V Gurung, D Ilic

The moisture content of iron ore during handling can range from the dust extinction moisture at the point of arrival at the port to the transportable moisture limit at the point of loading ships for maritime transport. Moisture content and ore composition, specifically fines content, have a large influence on ore flowability. Typically, elevated moisture can result in bottlenecks, downtime and lost productivity due to build-up, conveyor carry-back and blockages, increasing maintenance costs. On the other hand, low moisture can result in increased dust emissions influencing the environmental footprint and product losses. Managing the use of water across the supply chain is therefore critical for service life of equipment, productivity, but also has environmental and social impacts, affecting the social license to operate. Previously, experiments have shown that oscillations induced in iron ore during handling and transport can result in movement of moisture through the ore. This kind of moisture migration depends on the nature of these oscillations, such as the undulation of idlers during conveying, the inherent ore properties and the initial moisture content. Moisture has been observed to move either upwards and/or towards the bottom of the burden. These effects can be exploited to remove excess water from the ore influencing handleability and operation, however, the actual mechanisms of moisture migration are currently poorly understood. The study presented herein involves the use of simulation to examine moisture and ore interactions. Simulations using discrete element method (DEM) and coupled with smoothed particle hydrodynamics (SPH) are implemented to investigate the behaviour of moisture in wet ore in the presence of oscillation. This is conducted at a fundamental level first using glass beads and water which is then compared to iron ore at high moisture content. The results of the modelling are discussed in view of experiments conducted.

Sep 18, 2023

Nickel laterite HPAL circuits are known for their complexity and have presented a large number of challenges to process engineers worldwide. An attitude commonly encountered by the author is that the beneficiation of the ore is relatively simple and that the difficult problems are in the realms of hydrometallurgy. On a number of occasions beneficiation has become the 'poor cousin' in the process design phase. Another common theme is that significant difficulties are encountered when beneficiation circuits are started up, invariably slowing the ramp-up of the remainder of the circuit. In some cases the problems impact on throughput for a long period and can require major rectification capital. The HPAL Ni laterite projects encountered each have their own set of beneficiation problems that need to be understood before an appropriate circuit can be designed. This paper will discuss a range of design issues including geometallurgy, ore characterisation through laboratory testing, the application of appropriate sizing and analytical procedures, the selection of appropriate unit operations, materials handling of plant feed and products and setting meaningful plant design requirements.

Jan 1, 2008

By Bishop I, Toon S

To determine whether 130 felt earth tremors around Edwinstowe, Nottinghamshire U.M, which also experienced severe surface fissuring, were caused by coal extraction, a surface seismometer array was established around Thoresby Colliery. Over the next year, 785 microseismic events were detected. The spatio- temporal seismicity patterns are clearly associated with the commencement, continuing extraction and closure of faces. Of particular note are events which locate at the surface and appear to be related to the active fissuring. Events occur within days of commencement of production and cease when production finishes, with good correlation between face advance and hypocentral position. Naturally occurring microseismic events have also been detected up to 1 km ahead of active longwall faces in the Midlands using triaxial geophone packages grouted into the seam together with a surface seismometer in the top of the borehole. The quality of these data were very high and guided waves can clearly be seen with the dispersive characteristics associated with seam waves. In one experiment more than 2000 events were detected in only two days of monitoring even in a relatively noisy surface environment. This paper demonstrates how very accurate locations (5 10 metres) can be generated using three-component digital data from only one borehole. The surface seismometer and the borehole P-wave onset can give extra precision for the height of the event relative to the seam. The event distributions give a dynamic, three-dimensional image of the developing patterns of fracturing above, below and ahead of the longwall face with important implications for roof control, subsidence prediction and gas Migration.

Jan 1, 1992

The New Southern Railway (NSR) involves the excavation of approximately 10 km of single bore tunnel from Tempe Reserve, Tempe, to Prince Alfred Park (PAP). PAP is located just south of Central Railway Station in SydneyÆs Central Business District (CBD). From Tempe Reserve the alignment takes the tunnel under Sydney Airport including the main north/south runway. Sydney Airport is approximately 8 km south of the CBD. The NSR is being constructed by a private group, the Transfield Bouygues Joint Venture (TBJV). Transfield is a major Australian contractor and the French contractor, Bouygues, is providing the soft ground tunnel construction expertise and is also responsible for the design of the concrete segmental lining. This paper sets out to present in some detail the issues involved in tunnelling under the airport and in particular under the north apron, the main north/south runway and the new elevated roadway. The paper concentrates on these three areas on the airport with an emphasis on the following. The risks involved and measures taken to minimise the risks in tunnelling under the International Terminal north apron (with Jumbo Jets parked immediately above). Secondly, settlement predictions, settlement and runway operation criteria and the actual settlements that have occurred on the main north/south runway. Finally, the criteria that was developed during the construction of the deep bored piers for the elevated roadway at the Domestic Terminal as the TBM passed through this area of construction activity.

Jan 1, 1999

By Glasson K. R

The history of Ore Reserve classification and reporting in Australia is largely a history of the Australian mining industry itself. In the late 1800s, when the industry was dominated by small scale, high grade underground mines, Reserves (if estimated) were based on hand sampling and geological inference, and reporting of Reserves was either non-existent or of extremely variable quality. By the mid-20th century, the industry was dominated by large underground base metal and gold mines. Reserve estimation was coming under the control of skilled geologists and mining engineers, however Reserve classification and reporting standards continued to vary in type and quality from mine to mine. Today, large scale, low grade mining operations predominate, and Reserve estimates are generally based on extensive drilling results processed (with geological control) by computer. Through the efforts of a Joint Committee established by The Australasian Institute of Mining and Metallurgy and Australian Mining Industry Council, Reserve and Resource classification and public reporting has been standardised and controlled by adoption of the ""Australasian Code for the Reporting of Identified Mineral Resources and Ore Reserves"" released in 1989. The Code, which will continue to be modified and improved by the Joint Committee, has also been used as a basis for guides to reporting in other countries, and there is now some hope that this difficult and vexing topic may finally become subject to international standards and controls.

Jan 1, 1992

By A Nigam, K Biswas, R Sarkar

Because of the problems with 1st and 2nd generations of Advanced High-Strength Steels (AHSS), a 3rd generation of AHSS steels has become prominent and these steels have properties in between the 1st and 2nd generations of AHSS. However, although the 3rd generation of AHSS is a promising candidate as a replacement for its predecessors, there remain some challenges in processing these steels which are essentially medium Mn (Mn content ~ 5–7 wt per cent) and high Al (Al content ~ 1– 3 wt per cent) steels. The use of conventional casting powders based on the CaO-SiO2 system is unsuitable for high and medium Mn/Al steels. This work investigates the development of CaO-Al2O3- based mold fluxes for casting third-generation AHSS steel. Mold fluxes, with otherwise similar compositions but different C/A ratios, are tested and their crystallisation behaviour is examined using differential scanning calorimetry (DSC). A calcium aluminate phase having a composition Ca12Al14O33 was found to be the main crystalline phase in the mold fluxes. A decrease in crystallisation temperature was observed as the CaO/Al2O3 ratio increased from 1.00 to 1.33. The effective crystallisation rate constant exhibited an increase with decreasing crystallisation temperature, indicating a potential influence of nucleation rate on the overall crystallisation rate and suggesting an anti-Arrhenius behaviour in the crystallisation process of these mold fluxes.

Aug 21, 2024

This paper reviews the development and operation of a small underground tin mine in NE Tasmania. Tin mineralisation was discovered in the Lottah area in the 1880's with early alluvial and eluvial workings leading to the development of large low grade open pit operations. Apart from short lived activities operations ceased in 1915. Intensive exploration in 1978-81 outlined substantial tonnages of low grade tin mineralisation (0.2% Sn) of open pit material. An underground ore body was also located (800 000 tonnes 0.6% Sn). Spectrum Resources Australia Pty Limited acquired a 98 percent interest in the property in 1988. Mine and mill development began in early 1989 based on an underground mine utilising trackless mining using room and pillar with fill stoping. The milling circuit involves primary jaw crushing, Barmac secondary crushing to lmm, Mogensen and DSM screens with jigs and tables to make a wet concentrate. Final tin concentrates are produced by high tension and magnetic separation. Planned production rates are 500 t/day with a mine life of 6-7 years.

Jan 1, 1990

By Cunneen R. D, Murray A. M

Exploration in the vicinity of the abandoned Mt Coolon mine has shown that the shape and attitude of the quartz lode is controlled by the interaction between the lode and a converging syncline. Gold grades within the lode are enhanced along intersections with a welded ignimbrite, and decline rapidly where the lode intersects unwelded ignimbrite. Mineralogy and textures indicate the vein has an epithermal origin modified by a later intrusive event.

Jan 1, 1989

Gold at Renco occurs in association with pyrite, pyrrhotite, chalcopyrite and quartz and is confined to a series of brittle fractures and fault breccias (reefs) preferentially developed within an anastomosing ductile shear zone. During late Archaean crustal movements both the orebody and the enclosing host rocks were deformed within a series of east-north-east striking, southerly dipping, shear zones. The reefs within these shear zones are now texturally different to those away from the shear zones, and this difference is reflected by differences in the way the gold is distributed in the two reef types. These differences are not taken irto account by the software package currently being used to generate kriged plans of gold grade and reef thickness and this may explain some of the inaccuracies found in these plans.

Jan 1, 1990

By Dinuzzo P, Wychie J, Desoe C

The Selwyn Gold-Copper Mine is located 150 km southeast of Mount Isa within Proterozoic units of the Mount Isa inlier (Figure 1). Mineralization in the mine area is associated with strongly sheared ironstones and iron rich schists at the base of the mid- Proterozoic Staveley Formation. The ironstone horizons outcrop as a series of dominant ridges over a 10 km strike. Economic gold-copper mineralization has been defined in 4 separate zones within a 3.5 km length of the outcropping ridges. A current combined geological resource for the deposits is 5.3 million tonnes of 5.0 g/t Au and 2.02 Cu. Weathering of the deposits has resulted in a pronounced vertical zonation of mineralogy, especially copper, within the ore zones. This has produced 3 separate ore types which require different treatment techniques. The categorization is based on copper content and zones are termed leached (surface), oxide and sulfide. Ore removed from the pits will be mainly leached and oxidized with minor sulfide near the pits final depths, while the underground ore will be from the sulfide zone with minor oxide in some areas.

Jan 1, 1989