Search Documents

By N Tuffs, R Peace, S Xue

Mine gas control is a major issue in most of the gassy underground coal mines, due to its direct impact on safety, production delays and cost of production. Analysis of the gas data, from different collieries in Australia showed that longwall gas emissions have increased substantially over the years. Simply increasing the number of goaf holes in the panel or decreasing goaf hole spacing seems not to be effective, in controlling high goaf gas emissions. A major research project has been undertaken by CSIRO in collaboration with mine sites to address this goaf gas control issue with the aim of developing effective and optimum goaf gas drainage strategies. The project has combined extensive field studies with computational fluid dynamics (CFD) models, to characterise goaf gas flow patterns and develop effective gas control strategies. The research work specifically involved review of gas control issues at field sites, goaf gas monitoring, tracer gas tests, CFD simulations and extensive field trials. Field demonstration studies of the new optimum strategies have been conducted at two collieries in Australia. The project results have shown that the optimum strategies were highly successful, in improving the overall efficiency of goaf gas drainage systems, at both the field sites. Results of the goaf gas flow characterisation studies and field demonstration studies are summarised in this paper.

Jan 1, 2005

By D MacKenzie

The Rise & Shine Shear Zone is a shallow-dipping Cretaceous late metamorphic shear zone formed in a compressional environment. The Shotover mineralised system is dominated by normal faults with well-defined vein systems that cut across Miocene schist folds and faults related to the inception of the Alpine Fault. Despite the geological differences between these mineralisation systems, they share many common features of hydrothermal alteration that have resulted in disseminated gold in altered sheared schist. The most distinctive feature of both systems is the abundant ankeritic carbonate that has formed from decomposition of metamorphic chlorite. Excess iron from this alteration reaction combined with hydrothermal sulphur to form sulphides that host the disseminated gold. The chlorite decomposition reaction was reversed in the latter stages of both mineralisation systems, and this was accompanied by further gold emplacement in the Rise & Shine system.   Both alteration systems involved initial decomposition of metamorphic albite, followed by deposition of albite as a vein mineral in the latter stages. The fluid flow that yielded the disseminated gold was controlled by microshears that pervade host schists, in strong contrast to many Otago Schist vein systems where host rock alteration is absent. The ankeritic alteration in the Shotover and Rise & Shine mineralised systems has increased the volume of mineralised rock, and may have made suitable targets for large-tonnage, low grade gold deposits.

Jan 1, 2007

By C Pope, M Tannock

Mining exploration and development projects in Australia are being negatively affected by the highly complex regulatory and bureaucratic processes at all levels of government. These processes affect mining companies operating in Australia by impacting on timelines and the cost of developing a mining project. It is not uncommon for the granting of project approvals to take in excess of five years, meaning that mining companies struggle with productivity, efficiency, time frame and cost issues in respect to their projects in Australia. As the mining boom in Australia is moving from the investment to the production phase, it is now more important than ever to maintain a regulatory landscape that facilitates rather than discourages new investment.While one of our key arguments is that there is too much burdensome regulation and red tape in Australia, we are also strongly believe that regulatory intervention is necessary to ensure that appropriate checks and balances are in place to serve the public interest and manage environmental, health and safety, social and other development-related impacts that may arise from a mining project. However, the regulatory intervention in Australia has come to a point where it is excessive and starting to discourage valuable investment in mining projects for nominal return to the public. Excessive regulation or ‘red tape’ impedes productivity and competitiveness, deters investment and innovation and costs jobs, all of which ultimately impact on the growth of Australia and the standard of living of all Australians.This paper aims to examine and compare the federal, state and local regulations that govern mining projects in Australia. It will highlight how these regulations are unnecessarily complex, lengthy and duplicated and how they can be streamlined to reduce red tape. In doing so, the paper will evaluate the recommendations proposed by the Productivity Commission Report on Major Project Assessments released in 2013, which include the recommendation to move to a ‘one project, one assessment, one decision’ regulatory model.CITATION:Pope, C and Tannock, M, 2015. Project development and regulation red tape – a comparative analysis: does it need to be so complex?, in Proceedings Iron Ore 2015, pp 621–630 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J Theiler, B Beamish

Spontaneous combustion hazard assessment from an environmental impact perspective is not well understood and is seldom given due consideration in environmental impact statements. In surface mining operations, self-heating, leading to spontaneous combustion may occur when rock units containing reactive metal sulphides and organic carbon are disturbed by mining operations and exposed to the atmosphere. When these rocks are present self-heating will occur in situations where the rate of heat generated from oxidation reactions exceeds the rate of heat lost to the surroundings. The processes and mechanisms that lead to spontaneous combustion events are varied and generally complex. To effectively manage spontaneous combustion in surface mining operations, it is necessary to characterise the spontaneous combustion propensity of the geological materials involved. Until recently there has been no testing procedure for assessing the propensity of waste rock to spontaneously combust that has been adopted by industry. However, new developments in adiabatic test methods have proven successful in determining the self-heating behaviour of coal (Beamish and Theiler, 2015) and coal containing reactive pyrite (Beamish and Theiler, 2017). These adiabatic test methods have now been modified to assess the incubation behaviour of waste rocks and can be used for their spontaneous combustion characterisation in advance of mining (Beamish and Theiler, 2016). The new method provides a practical means to establish the likelihood of developing a spontaneous combustion event for the specific site conditions. This paper presents examples of the use of a cost effective first pass filter for assessing spontaneous combustion potential of waste rock based on geochemical data from four surface mines. This is supported by adiabatic Incubation Test results for three of the mines and visual examination of cores for one of the mines. CITATION:Theiler, J and Beamish, B, 2018. Valid spontaneous combustion hazard assessment for surface mine environmental impact statements, in Proceedings Life-of-Mine 2018, pp 64–67 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By A Purton, C Taylor, E Conroy

The spatial modelling of geometallurgical domains is an important step in the characterisation of an ore deposit allowing for the quantification of various rock types, their differing rock properties and the overall value of a project. The traditional approach to modelling such features is through the use of deterministic models, where a single estimate of the extents and structure of the ore deposit is mapped out by geologists based on available data and their interpretation of the geological processes. Any uncertainty in the layout of different domains is not accounted for and heterogeneities of chemical and physical properties of the orebody are likely underestimated. Spatial machine learning techniques can be used to derive geometallurgical categories, or classes, from multiscale, multiresolution and high dimensional measured rock properties. Subsequently, geostatistical simulations of these classes can be applied to obtain multiple equiprobable realisations that define the layout of the geometallurgical classes at unknown locations between boreholes, or domains. In-turn these realisations can be used quantify the uncertainties in the location of boundaries between different domains. The development of a workflow for defining geometallurgical domains and later geostatistically simulating them across the Orebody H; a complex stratabound Bedded Iron Ore deposit located in Western Australia’s Pilbara region is demonstrated. This could be used to identify zones of high uncertainty where collection of additional data might help mitigate or minimise risks and in turn improve forecast production performances.

Mar 22, 2022

By J Joughin, D Kyan, L Rollin

In line with the 2015 Paris Agreement and corresponding climate disclosure requirements, many mining companies have publicly disclosed that they are developing and/or implementing ambitious decarbonisation strategies. Sometimes these strategies can be linked to the development of community programs and/or the creation of a positive legacy post-closure. Renewable power is key to most decarbonisation strategies – some mines will get this from external sources and others will establish on-site power generation and storage facilities. A range of options are available to develop renewable power generation (eg solar panel, wind farm, hydropower) and energy storage (eg battery, hydrogen, pumped hydroelectricity). Land access, impact assessments, planning and environmental approvals are required to establish new facilities. Host communities are more likely to be in favour of, or at least will accommodate, new power supply developments if these are planned with a benefit to the communities. Transitioning to renewables raises new challenges. Among these are high upfront costs and access to capital, energy demand variability, supply intermittency and variability, storage limitations, grid stability and reliability, transmission and distribution infrastructure constraints. Compounding these challenges are issues such as infrastructure resilience to extreme weather events (eg heat, wind), land use and access, lengthy permitting processes, community perceptions, skilled labour requirements, and meeting mine closure objectives. Renewable energy sources provide a more decentralised source of energy that reduces reliance on imported fuels, thereby increasing energy security and lowering production costs. On the contrary, implementing renewable energy could lead to potential negative impacts such as visual perception from the community, competitive land usage, electricity price raises due to upgrading infrastructure and the use of electricity storage capacities. As part of the definition of an environmental and social management plan, participative stakeholder engagement is required to identify benefits to the communities. For example, among the recognised benefits of developing solar panels (increase job opportunities, reduce soil erosion), various technologies have been experimented globally for the last ten years and are emerging due to their proven community benefits. Key findings to enhance those benefits can range from the development of innovative practices such as ‘agri-/aqua-voltaic’, ‘solar grazing’ to optimise land usage and stimulate the local economy (Table 1), to the implementation of technologies providing services to communities such as mobile water desalination plants or ‘smart grid’ systems to minimise energy clipping during peak-load of oversized renewable energy facilities (Table 2). While developing those synergies, careful management is required to avoid creating superfluous energy service needs from community programs. Energy sufficiency should remain a key principle according to the sufficiency, efficiency and renewable framework of the Intergovernmental Panel on Climate Change. Darby and Fawcett (2018) define energy sufficiency has ‘a state in which people’s basic needs for energy services are met equitably and ecological limits are respected’. Sufficiency tackles the causes of the environmental impacts of human activities by avoiding the demand for energy and materials over the life cycle of buildings and goods. Efficiency tackles the symptoms of the environmental impacts of human activities by improving energy and material intensities. The third pillar, renewables, tackles the consequences of the environmental impacts of human activities by reducing the carbon intensity of energy supply (Cabeza et al, 2022). Life of Mine Conference 2023 | Brisbane, Australia | 2–4 August 2023 34 This paper provides project developers, decision-makers and regulatory authorities with ideas on synergies between renewable energy options and community development programs. These can be considered to enhance stakeholders’ support for implementation of decarbonisation strategies.

Aug 2, 2023

By A J. Burchell

The introduction reviews the tunnelling carried out in Singapore since the early 1980s. Between 1983 and 1990, Phases 1 and 2 of the mass rapid transit system were constructed. These included some 20 km of bored and cut and cover tunnels together with 18 underground stations. Some particular points of interest in this massive project are briefly commented upon. Reference is also made to other underground or underwater schemes undertaken during this period such as the proposed large caverns project and the submerged tunnel to Pulau Seraya. A description of the subsurface works, now under construction in Singapore, follows. This includes an all underground North-East railway line 20 km long with 16 stations. At a budget of US$ 3 billion, this is a major civil engineering undertaking. Another project is the extension of the railway to Changi Airport which involves 3.5 km of twin tube tunnelling together with a major underground station which is fully integrated into the airport terminals. An on-going program of further major railway extensions over the next 10 to 15 years is in place and an outline is given of some of the most important underground sectors. Other proposed projects such as the underground roads system and the deep level sewers are briefly described. Together they demonstrate the very significant volume of underground construction scheduled for the next century in Singapore.

Jan 1, 1999

The history of the discovery and development of the Kambalda nickel orebody. is reviewed and the decision to process the Kambalda concentrates by the Sherritt-Gordon process at Kwinana is discussed. The Kwinana Nickel Refinery is described and the problems encountered in the first year of operation are Outlined.

Jan 1, 1971

By Dawson CF

About 17% of the world's present day oil supplies comes from wells drilled in the continental shelf of some 28 countries. The demand for oil is increasing each year and is expected to quintuple in the next decade. In the same period, the demand for gas will climb to at least 20 times its present rate. In the next decade, the percentage of oil and gas obtained from offshore is expected to rise to nearly half the world's consumption. The offshore oil industry is currently striving to achieve new technological advances in the field of deep ocean operations, especially in face of adverse seas. While the emphasis was put on drilling vessels for exploration, the industry was slow in developing effective offshore construction vessels. Until a year ago, construction vessels were but large barges with construction equipment mounted on their decks. These vessels all shared the same severe limitation: When the sea exceeds a five-foot wave height (and in some cases as little as three feet) the conventional construction barge is forced to suspend operations. In face of an oncoming storm they must run for shelter. Their utilization, therefore, is limited and in rough weather areas, such as the North Sea or the Bass Strait is lower than 50%.

Jan 1, 1970

By Reed M. E, Cloutt B

Particulate samples were taken from the gas space in the settler of the Kalgoorlie nickel smelter using a vertical sampling probe and a specially designed isokinetic sampling probe which also quenched the samples. The vertical sampler was found to give unrepresentative samples. Suction thermocouple measurements of the gas temperature were also made. Using the isokinetic probe samples were taken at four points ranging from near the base of the reaction shaft to the base of the uptake at depths up to 1.5 m into the settler. Dust loadings and the sizing of the samples were determined. These parameters were found to be most affected by sample position and depth. The dust loading decreased along the settler but increased with depth. The loadings varied from zero near the roof to several hundred g Nm 3 near the slag. The dust also became coarser with increasing depth into the settler. Examination of the samples showed them to consist of spherical particles the largest of which were about 500 microns in diameter. The dust was mainly composed of mixed iron/nickel oxides with a little sulphide.

Jan 1, 1991

By R Yang

This paper presents a fragmentation model for large production blasts in an open pit or underground environment. The paper shows that the particle velocity is directly related to pressure, strain, and strain rate and so it can be considered as driving force and mechanism of rock fragmentation. This is supported by the fact that a vibration with a larger peak particle velocity (PPV) generates larger disturbance in rock and so finer fragmentation or more blast damage than a low PPV. The crack distribution in rock from impact is based on findings from previous researchers (Seaman, Curran and Shockey, 1976; Liu and Xu, in press). The fragmentation size is calculated at three-dimensional grid points within a blast. The fines and oversized blocks are calculated explicitly – the fines generated close to blastholes and big blocks far from boreholes are modelled naturally. The multiple blasthole fragmentation (MBF) model takes surveyed irregular geometry of the free face of a blast as the calculation boundary. The MBF can model fragmentation with over one million grid points. Examples of the model’s field comparison are also included.The PPV at a calculation grid is estimated based on the same approach used for the near field non-linear vibration model (Yang and Scovira, 2007). The method is based on the dominant charge for a calculation grid point, non-linear charge weight superposition within a charge and from multiple charges, strain wave broadening, and amplitude attenuation with distance from a charge segment. The blasthole confinement affected by earlier firing charges is also taken into account.The MBF model inputs from blast design, such as: location and orientation of each blasthole, stemming length, blasthole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect of the delay and its scatter in each blasthole on fragmentation and has a statistical modelling capability for geological random variation on attenuation of particle velocity wave. The wave reinforcement due to instantaneous waves arriving or diminishing cooperative contribution due to long delay intervals between charges is also simulated.The results are displayed in 3D volumetric plots, contour of fragmentation in cross-sections, and size passing curves for a whole blast or a region of the blast.CITATION:Yang, R, 2015. A multiple blasthole fragmentation model – its concept, formulation, capability and field comparison examples, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 177–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R Shaw, T T. Neidel, C Adams

Sampling equipment manufacturers endeavour to ensure that the mechanical equipment installed in sampling systems are designed and manufactured to adhere to the requirements of the International Organization for Standardization (ISO) or other standards relevant to the application. The mechanical parameters necessary to achieve these standards can be well controlled and requirements such as constant speed can be met through good mechanical design and engineering. However, when the equipment is installed and put into operation, the ISO compliance of the system is out of the hands of the equipment manufacturer and handed to the operator, who may be a generalist control system integrator.Making a sampling system perform according to standards, and being able to monitor and report on compliance require that the sampling system knowledge and the control integration is combined and applied in an integrated approach. Using a dedicated library of control routines developed for sampling can change a system from having compliant equipment to being a compliant system. The library has to include monitoring of relevant parameters and control and reporting on sampling parameters.CITATION:Neidel, T T, Adams, C and Shaw, R, 2014. Control and monitoring of International Organization for Standardization compliance for industrial sampling systems, in Proceedings Sampling 2014 , pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By D Laurence

Australians are at the forefront of exporting their mining expertise in a number of areas. Minerals education is just one example. The growing economies of Southeast Asia host some of the most prospective mineral fields in the world. Laos for example, hosts the world class Sepon and Phu Kham copper-gold deposits. The Philippines has the fifth largest global mineral resource inventory. These and other countries in the region lack the mining engineers, geologists and metallurgists required by international mining companies to ensure their operations are sustainable. This paper describes the author’s experience in working with mining schools in Southeast Asia and specifically the Philippines, Cambodia, Laos, Thailand and Vietnam. Various strategies to ensure sustainability and lessons learnt are presented.

Nov 22, 2011

By G P. S Resende, D E. G Oliveira, E A. S Baeta, T F. Bravin

There is currently in the mining industry, as well as in other industries, a movement seeking to increase investments in decarbonisation processes to help combat global warming. Among some initiatives taken is replacing diesel-powered mobile equipment in the mines with electricity-powered equipment, such as electric off-highway trucks or even belt conveyors in the mining operation. Samarco is a Brazilian mining company that since its conception has used a conveyor belt mining system in its mining operation, using only a small number of trucks to complement the mining process. This mining process that combines conveyor belts and trucks has brought environmental gains for the company since the environmental impact of conventional truck-only mining is greater than that of the combined system. To measure these gains, a medium-term mining plan was developed in which two fleet scenarios were detailed. One scenario contemplated a high level of detail of belt mining seeking its maximisation, while the other considered the operation performed 100 per cent by trucks, eliminating the use of conveyor belts. Through the comparison of these two scenarios, it was possible to make an inventory of atmospheric emissions and greenhouse gases for each one of them considering data such as types of equipment, diesel consumption, total distance travelled and energy consumption. The results showed that the fleet scenario with conveyor belts results in periods with up to 15 per cent less greenhouse gas emissions and 37 per cent less total particulates compared with the truck-only scenario. Therefore, the results confirm the environmental benefits of the method and the need to look for ways to even expand it in future operations through a study to identify the potential areas in the long-term mining plan.

Sep 18, 2023

By J Zhou

Gold in sulfide ores is associated predominantly with sulfide minerals and occurs as both microscopic and submicroscopic particles. In non-refractory sulfide ores, gold occurs mainly as coarse- and medium-grained particles. Minute inclusions and submicroscopic gold usually account for a minor portion. In contrast, gold in refractory sulfide ores occurs mainly as minute particles and submicroscopic gold, and microscopic gold usually accounts for an insignificant portion. In gold ores containing carbonaceous material, the preg-robbing nature of carbonaceous material may impose challenges on gold extraction and cause gold losses. To extract gold from refractory sulfide ores, the ore needs to be finely ground and preoxidation is often required. Sulfide host minerals must first be oxidised to create a porous structure through which the cyanide leach solution can penetrate to reach the colloidal gold particles. The oxidation is traditionally achieved by roasting, autoclaving or bacterial oxidation. In carbonaceous sulfide ores exhibiting a preg-robbing nature, the carbonaceous material needs to be treated by roasting, autoclaving or other means to minimise the preg-robbing effect. As a predictive and troubleshooting tool, the gold deportment study plays an important role in gold metallurgy. It determines the deportment of gold in an ore or mill product and identifies the mineralogical issues that may affect or may have affected gold extraction. The information acquired from a gold deportment study can be used to assist in process selection, flow sheet development, recovery improvement and reagent optimisation.CITATION:Zhou, J, 2013. Deportment of gold in sulfide ores and implications for gold extraction, in Proceedings World Gold 2013 , pp 433-442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Gray E, Banks J

In mine site revegetation, exotic grasses are more commonly used than native grasses. This is due to unavailability of native grass seed on a commerical scale and lack of information on agronomical aspects of native grasses. This paper lists a number of native grass species that have the potential to grow well on mine sites, and provides some information on their seed collection, processing and germination. Further, it demonstrates via results of a field trial conducted at Ranger Mine spoil the relative performance of ten native grasses and Rhodes grass. It is concluded that (i) some native grasses have similar ability to grow on mine spoils compared to Rhodes grass and (ii) the use of native grasses have added advantages in ecosystem restoration.

Jan 1, 1994

This paper will address this question from the point of view of a drill and blast engineer or researcher working in open cut and underground mining operations. The paper will establish a common set of reference standards for high-speed imaging and data capture, which engineers and researchers can apply when deciding which type of imaging technology is appropriate. It will present an overview of current image analysis technologies and practices in use across a range of appropriate scientific fields and draw lines of commonality of approach between these fields and the field of mining and blasting applications analysis and research. In addition, the paper will examine the different technologies from an image quality and data stream reference point, ease of operation, cost, and reliability parameters. Finally, this paper will present an argument for the hybridisation of established and new technologies which could provide a more beneficial approach to the use of imaging as a tool of quality control, research and analysis in the mining based industries. This will include a novel approach to digital high-speed imaging and data analysis in the field, which should deliver high-quality images and data analysis in a time frame that is more appropriate to the need for immediate action, analysis and problem solving.

Jan 1, 2007

By E Asakpo, S Chaffer, A Heath

Newmont has had continuous production at their Ahafo operations, Ghana, since 2006. In 2013, Ahafo initiated an efficiency programme to improve mill performance and reduce energy consumption. Following this assessment, a Turbo Pulp Lifter (TPLTM) was installed in the Ahafo SAG mill in April 2015 to replace the existing radial pulp lifters. Plant operational data showed delivery of a power saving of 10 per cent, an improvement in throughput of 3.3 per cent, with no loss of grind size. Pulp lifter life was also doubled from 11 to 22 months.However, during subsequent relines when the grates were removed it was found that one in four of the outer pulp lifters were wearing at a faster rate than the remainder. This was investigated by Discrete Element Method (DEM) modelling, which predicted some overtopping and internal recycle within the pulp lifter. Significantly, the model predicted that the recycled material would pass back down every fourth outer pulp lifter, matching the field observations. Subsequently, the DEM investigation was continued and became an R&D project to improve the TPL design. The results are summarised here, leading to the development of the next generation Spiral TPLTM.CITATION:Heath, A, Chaffer, S and Asakpo, E, 2018. The development of optimised pulp lifter design for the Ahafo SAG mill using discrete element method modelling, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 585–594 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Karlson R, Rispin M

Chemical admixtures are not commonly included in the variety of backfill mixes used in the mining industry. This may be attributed to several reasons including, but not limited to: the perceived high added cost, 2. the lack of awareness about their proper use, and 3. the lack of knowledge about their features and benefits. In the construction industry today, however, chemical admixtures are used in the majority of the concrete produced, enabling concrete to become a more cost-effective building material. They also enable construction crews to meet demands for year-round construction, quicker completion of construction projects, and improved concrete properties. The high demand for chemical admixtures in the construction industry has led to numerous innovations in admixture technology in recent years. Some of these chemical admixtures have been found to enhance the production, transport, placement, and in situ properties of backfill mixes. Others have been found to reduce the cost of such mixes while maintaining, and in some cases improving, their physical properties. In this paper, a few of such innovative admixture technologies are discussed. The benefits, imparted by these technologies to backfill mixes as well as performance data on their use in several backfill applications at various mines, are presented.

Jan 1, 1998

By R Justa Cámara, J María Bertrán Llop

"The need for suitable geotechnical characterisation of the rock mass for underground construction is evident. The enlargement project of Railways of the Generalitat of Catalunya (FGC) in Sabadell is a patent example.In general, it is uncommon to encounter problems in the identification and characterisation of certain relevant weak rock formations, which affect project designs. However, all materials should be properly studied, as mischaracterisation can lead to a suboptimal design, resulting in construction problems during the course of the work.Good quality rock is generally not difficult to characterise, but this is not the case for Quaternary or Tertiary cemented soils. Geotechnical investigations based on boreholes do not provide enough information because samples are often badly damaged during the drilling process, if appropriate techniques are not taken. The samples can be altered and may not be representative of the in situ?material.The design and construction of the extension to the FGC line in Sabadell highlighted the importance of the characterisation of Quaternary and Tertiary cemented soils, in particular their rigidity and its underestimation. The twin tunnel project had a total length of 5.1 km, including five stations with 3.5 km excavated by tunnel boring machine (TBM). The remaining 1.6 km was constructed using cut and cover methods. The TBM portion of the tunnel had a bored diameter of 6.83 m with an internal radius of 3 m and 0.25 m thick precast concrete segments. Much of the tunnel alignment passed through and was affected by the presence of certain stiff layers of Quaternary cohesive materials.In this paper the TBM challenges faced will be discussed in detail. In particular:  TBM excavation rate reductions and overheating problems due to the required excessive thrust and torque floating problems in the lining due to nil earth pressure over the rings and the development of an improved, controlled setting time mortar to address this issue block-in and block-out methodology for each station, in some cases with internal blocks to prevent earth pressure drops and soil scouring the relevance of performing simpler solutions, for example, hyperbaric interventions to examine the cutter wheel tools when it has been shown that interventions under atmospheric conditions were equally feasible the implementation of conventional bivalve machines as standard procedure for excavation of diaphragm walls in stations, where in fact, hydrocutter machines or pile boring machines may have been required, given the mechanical characteristics of the materials to be dug out.CITATION:Justa Cámara, R and María Bertrán Llop, J, 2014. Underground extension of the FGC line in Sabadell through cemented soils, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 161–170 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 17, 2014