Search Documents

By G M. Volkmann

Pipe umbrella support systems – also called canopy tube systems – have been used successfully for tunnelling in challenging ground conditions since the 1970s. Historically, the drilling unit was the limiting factor for pipe umbrella installations – less attention has been paid to pipe couplings and their influence on labour time and load-bearing capacity.This contribution investigates the influence of the type of pipe connection on the load bearing characteristics of a connected pipe and discusses associated influences on design calculations and installation performance. Standard thread connections reduce the effective cross-section and thereby load-bearing capacity in the connection area. To achieve design parameters, over-dimensioning of the un-weakened pipe section is the only way to overcome this limitation. Recently, two new, alternative connection types were designed and developed for connected pipe umbrella pipes. The first one is the nipple coupling, consisting of fitting with a threaded connection that is pressed and welded into the ends of standard tubes. The second type is the squeezed connection, which mechanically connects non-threaded pipe ends, achieved by force-fitted squeezing from the drill rig. Both coupling types have technical as well as operational advantages compared to the common thread couplings, which are the weakest point in the support system.In the following sections significant technical differences are explained, design values given and a site example presented to illustrate the operational advantages of the newly developed coupling?type.CITATION:Volkmann, G M, 2014. Development of state-of-the-art connection types for pipe umbrella support systems, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 333–338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J R. Ruiseco, D La Rosa, L Julian, W Hunt

The DeGrussa copper-gold deposit is located 900 km North of Perth. Copper-gold bearing massive sulfide lenses occur in lower greenschist facies meta-sedimentary and mafic volcanics of the Bryah Basin. Regional folding, faulting, and tilting of the stratigraphy primarily occurred during the Capricorn Orogen (Johnson, 2013). The Shiraz Fault and Merlot Fault are regional oblique-sinistral faults that offset the DeGrussa massive sulfides lenses into three fault blocks by ~350 m and ~120 m, respectively. A network of deposit-scale brittle-ductile faults splay from, and in one example are cut by, the Shiraz and Merlot faults. This results in localised ore displacement, selvage alteration and degradation of the rock mass integrity. Historically, only the Shiraz and Merlot Faults were modelled and validated during mining and grade control. The requirement for a comprehensive structural model became more relevant as mining became advanced and confining stresses on local rock mass became more complicated. The DeGrussa Structural Model has been developed to delineate areas of structural complexity and is an important tool in mitigating rockfall risk through well informed technical design. During this process, every accessible excavation was walked and structurally mapped. New workflows in Leapfrog Geo and new technology, including an app that runs on mobile phones streamlined the validation process. Drill hole orientation was a limiting factor during validation. At the time of writing this submission, the DeGrussa Structural Model consists of 34 faults, and is now an important tool for the Technical Service team when developing mine plans and schedules. Applied structural geology is often seen as exclusive to those with a PhD in the field. Faults at DeGrussa have been modelled and reconciled by a Mine Geologist and Geotechnical Engineer, using first principles geological characterisation. This is a simple process that demonstrates any geologist can contribute to a structural model, provided they understand the fundamentals of unbiased structural measurements and consistent record of observation

Mar 22, 2022

By B Besa, E K. Chanda

It has long been recognised that narrow vein mining needs innovative approaches to mine access and mining methods in order to improve the economics of this vital part of the mining industry. The mining equipment used currently requires large openings in narrow vein-type deposits making mining operations uneconomical. In view of this and other shortcomings of the current mining practices, a study was initiated to investigate the potential of using low profile electric loader with mounted conveyor in conjunction with the electric monorail haulage system (EMTS) to load and haul the blasted material, particularly in decline development and main haulages. Computer simulation based on the General Purpose Simulation System/Henrikson (GPSS/H) is used to model the system and evaluate its performance. The results are compared with those for conventional mining using trucks and loaders. The EMTS provides competitive haulage rates in substantially smaller excavations than is currently achievable. According to simulation results, the electric loader in conjunction with the EMTS had the same number of blasts as the conventional system and hence the same advance rate of 3.33 m per 12 hour shift. Furthermore, the total drill-blast-load-haul cycle time was less than the conventional system by one hour.CITATION:Besa, B and Chanda, E K, 2012. Evaluation of low profile electric loader in conjunction with electric monorail haulage system in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 221-228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By P B. Hills

Almost a quarter of a century since Bridges (1993) documented techniques for the assessment of ground conditions in a seminal paper in the Proceedings Second International Mining Geology Conference, the necessary role of the geologist in recording geotechnical data on exploration properties and in mines remains. Typically, the geologist is the first professional on the exploration property. Of course, most exploration properties don’t become mines. However, when a property does start to come together and form a coherent mineral deposit and professionals from across the minerals industry spectrum, including specialist geotechnical engineers, become increasingly involved, it remains the geologist who has the most intimate knowledge of the deposit. By association, that knowledge extends to the character of the rock mass.Throughout the various phases of prefeasibility, feasibility, construction and production, culminating in the mature mine, the knowledge of the rock mass held by the geologists continues to grow. In the current era of minimising cost and optimising profit, meeting the requirements and expectations of stakeholders ranging from fellow employees to investors, industry and financial regulators and the broader public, in a social environment where occupational health and safety concerns are of uppermost concern in every endeavour, the value of the geologists’ observations cannot be understated. Mines nowadays employ more geotechnical engineers than they did in the early 1990s when Bridges (1993) wrote his paper. More funds are available for specific geotechnical investigations of exploration properties and mines; none-the-less, those programs remain limited in their extent and there is a wealth of additional data available for collection with the appropriate training, at little additional effort. Fundamentally it is all about the numbers. Any hole not geotechnically logged is a hole that will need to be drilled again if the data is required. Any face, surface or underground, not geotechnically mapped is one that may need to be mapped a second time. That doesn’t mean every hole or every face. However, it is the proposition of this paper that the opportunity for additional geotechnical data to be gathered during traditional geological investigations is an opportunity that cannot be ignored. Occupational health and safety requirements demand that the geotechnical risks associated with mining are appropriately managed. Mining regulations in most Australian and overseas jurisdictions requires the consideration of geotechnical risk through formalised management plans. The Joint Ore Reserves Committee (JORC) Code requires the consideration of modifying factors more than ever before. The benefit to be realised through improved geotechnical understanding by geologists on the ground leads to improved occupational health and safety, optimised reporting compliance, and improved financial and social outcomes for the exploration property and ultimately for the mine that follows.CITATION:Hills, P B, 2017. The necessary role of the geologist in geotechnical data gathering, in Proceedings Tenth International Mining Geology Conference 2017, pp 347–354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By J Seccatore, T Marin, M Cardu, G De Tomi, F Galvão, A Rezende, E Melo

Small-scale mining operations are characterised by a large variety of equipment availability and a high level of operational flexibility. Mine planning is usually scarce or absent in small quarries in Brazil, and mine management generally focuses on daily operations. As a result, analysis of the effects of unit operations, such as blasting, over the whole mining process is often neglected. The goal of the following project was to study the effect of production blasting on loading and hauling times, secondary breaking times and primary crushing times at the Experimental Mine of the Research Center for Responsible Mining of the University of São Paulo, Brazil. The operations analysed included blasts that performed:under the average operational standard, defined in this paper as Case 1according to quarry standards, defined in this paper as Case 2.In order to establish the effects of blasting on the downstream process, three key performance indictors were used:The time taken to load the truck, when there is the need for material selection. Due to the fact that we do not have an operational baseline, the increase in time cannot be established, meaning that we must content ourselves with comparing the mean time in each scenario.The average time used for secondary breaking machinery.The time required for the primary crusher to fully process the load of a single truck. The results obtained indicate correlations between the coarseness of the blasted material and these operational times. Solutions are suggested and evaluated for the improvement of the small-scale mining process.CITATION:Marin, T, Melo, E, Seccatore, J, Cardu, M, Galvão, F, Rezende, A, Bettencourt, J and De Tomi, G, 2015. The effect of drilling and blasting performance on fragmentation in a quarry and time for loading, secondary breakage and crushing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 355–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By G McCullough, J Bassan, d P. Knights, C T. Farrelly

By 2045, carbon-neutral mines will be economically producing products that are vital for the world’s transition to renewable energy. After overcoming significant technical challenges (and the investment of significant capital), leaders have successfully eliminated the use of diesel and other fossil fuels by introducing a wide range of new decarbonisation technologies. These leaders will be reaping the benefits of lower production costs (resulting from elimination of diesel), stable and predictable operations, and easier access to capital for their future projects. This paper describes a future scenario of how a net zero carbon and zero-entry mine could operate by taking maximum advantage of technologies in development or already proven in other industries. Some miners have been unsuccessful in their efforts to reach decarbonisation targets. Instead, they have been forced to close or offload their assets to be acquired by operators with better sustainability credentials, or, in some cases, to indigenous or community-based enterprises with vested interest in making operations viable and sustainable. Regardless of ownership structure, all successful mining operations will have fostered strong and positive community relations that bring education, health, security and economic development opportunities to the communities while respecting their traditions, land-uses and culture. As shallow, easy to mine deposits have become scarce, the majority of new mines are underground. Advancements in electric underground technology and the feasibility of ‘zero entry mining’ (with no personnel in active mining zones) has made it increasingly possible to economically operate underground mines, even at shallow depths. The newest mines have a near zero footprint on the surface, produce no harmful by-products, and are employing in-place or in situ methods of extraction that are efficient and low impact. Surface land-uses, such as agriculture and renewable energy generation, continue in the immediate vicinity of the mine, with no significant ground disturbance, community impact or environmental footprint.

Sep 1, 2024

By P Brown, M Nagarajan, A Green, P Dare-Bryan

Coal loss is an important issue at many coalmines, with losses of five per cent being common. The type of loss varies from mine to mine but is dependent on mine strata, the drilling and blasting processes applied and the mining method used. Typical coal loss mechanisms from the drill and blast process are coal roof damage and edge loss. Usually a reduction in coal loss is in direct competition with the need to provide material that is well-fragmented and a muck pile that has the required cast percentage. These competing issues were addressed over a two-year period at a mine in the New South Wales Coalfields by implementing a five-step approach. This was centred around building an understanding of the coal loss mechanisms utilising proprietary heave- modelling software, measuring coal losses by comparing survey to drill and/or gamma logs and implementing appropriate coal loss reduction processes. The end result exceeded expectations with a 95 per cent reduction in coal loss. Mine excavation productivity was maintained and coal loss minimised to less than one per cent of the in situ coal block.CITATION:Nagarajan, M, Green, A, Brown, P and Dare-Bryan, P, 2015. Managing coal loss using blast models and field measurement, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 429–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Control of construction projects is the responsibility of the Project Leaders who have the authority to make decisions. Project Controls cost and scheduling systems provide the Leaders with timely information on which to base their decisions.The Client (Owner) will invest up to three per cent of the project cost on Project Controls. To ensure that this investment is effective, the Owner or Manager must have a clear understanding of the information required from the Project controls systems. If appointing a single Managing Contractor, the Owner or Manager must stipulate what is and what is not required from the Project Controls Systems. There are numerous computer programs available for scheduling and cost control and it is important to select systems which best serve the Owner's needs.

Jan 1, 1993

By G R. Hancock, J F. Martín Duque

Post-mining landscapes are required to geomorphologically and ecologically integrate with their surrounds (Martín Duque et al., 2015). Designing and constructing an erosionally stable landform is the first and arguably most important part of the rehabilitation process. Without an erosionally stable landform topsoil and nutrients are lost, shallow groundwater is depleted as well as when excessive erosion occurs, expose suboptimal materials. Here we examine the ideas of geomorphic design and rehabilitation and how the landform can be tested and enhanced using computer based design and landscape evolution models. Specifically we evaluate the complementary capabilities of landscape modelling (SIBERIA) (Hancock and Willgoose, 2017) and geomorphic design software (Natural Regrade with GeoFluv) (Bugosh et al., 2016), in order to maximise erosional stability on post-mining landscapes (Zapico et al., 2018). CITATION:Hancock, G R and Martín Duque, J F, 2018. Geomorphic design and landscape evolution modelling for best practice mine rehabilitation, in Proceedings Life-of-Mine 2018, pp 119–121 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Y Li, D J. Williams, E Topal

A mine waste rock dump does not have any intrinsic value, yet is an inevitable structure in surface mining operations. Since the purpose of mining is to maximise profit, possible expenditure reduction in hauling waste rock to the dump, which can represent up to 50 per cent of the total operating cost, is highly desirable. Apart from cost, potential acid mine drainage (AMD), due to seepage from surface waste rock dumps containing reactive waste rock, could threaten the ecological balance, drinking water supplies and irrigation systems downstream from a mine site. In order to minimise these potential risks, selective placement of benign and reactive waste rock, and the encapsulation of reactive waste rock by benign waste rock, need to be carried out during the construction of the rock dump.In this paper, a new methodology, based on mixed integer programming (MIP) is developed to manage waste rock dumping. The model aims to minimise waste rock haulage costs by locating the optimum destination(s) for each waste rock block, while at the same time controlling the placement of reactive waste rock to minimise the potential for AMD. Tests on small-scale virtual data demonstrated that the model is capable of dealing with selective placement of different waste rock types, encapsulating reactive, potentially acid forming (PAF) waste rock, and stockpiling benign waste rock for encapsulation and rehabilitation purposes. The solution time for the MIP model is far less than the traditional manual approach, and the resulting schedule is up to 46 per cent more cost effective.CITATION:Li, Y, Topal, E and Williams, D J, 2012. Mathematical approach for better mine waste rock dumping management, in Proceedings Life-of-Mine 2012 , pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By H Kurth

Mining geologists utilise many technologies to map, sample, measure, model and plan before and during the mining process. Predicted ore quality rarely corresponds with feed quality determined by process operators. Objectively measuring conveyed material quality accurately in real time avoids disagreements over mined ore quality and generates opportunities to improve mill feed quality.This paper discusses the well proven PGNAA (prompt gamma neutron activation analysis) technology used in the GEOSCAN-M elemental analyser that is ideally suited to measuring composition of primary crushed conveyed material in real time. Representative, continuous, fully penetrative measurements are unaffected by particle size, belt speed, mineralogy, dust or layering on the conveyor. Material can be directed to processes or stockpiles by utilising measurement increments of typically one to five minutes and then activating diverters to direct increments to the correct location. Waste, low-grade or deleterious material can be rejected to waste dumps or stockpiled for later processing. Material meeting a product specification can bypass unnecessary processing. Paybacks in weeks have been achieved for such applications. Process operators are able to control the blend of ores fed into the mill to improve processing performance and use measurements for ore reconciliation and metal accounting. Utilising the technology to upgrade ore quality after mining and before processing is beneficial in improving plant economics.The technology has been successfully utilised in base metals, ferrous metals and industrial minerals. Mining geologists can determine ore quality being produced in real time and modify the ore quality prior to milling. Ore feed quality measurements are also used by process operators in optimising plant performance. The elemental content can help identify geometallurgical domains as well as other major changes in quality, which may affect processing. This paper outlines proven applications and case studies and proposes some innovative applications.CITATION:Kurth, H, 2017. Measuring ore quality using real-time on-belt elemental analysis – more than grade control, in Proceedings Tenth International Mining Geology Conference 2017, pp 213–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Armstrong A

Queensland is Australia's second largest mining state with world-class deposits of coal, base metals, bauxite and magnesite. The total value of Queensland's mining production is about $5 billion per annum, and coal accounts for around 55 per cent of that total. The environmental issues which arise as part of management and regulation of the industry are resolved within the EMOS process. The Environmental Management Overview Strategy is the cornerstone of the policy 'Environmental Management for Mining in Queensland' developed jointly by the Queensland Department of Minerals and Energy and the mining industry. The Gordonstone Coal Mine is the largest underground mine to gain approval under the new policy. Accordingly, Gordonstone has a well planned environmental management program which takes into account site-specific factors and provides for continuous compliance with the provisions of the Mineral Resources Act in a self-regulatory context.

Jan 1, 1994

By A L. de Ambrosis, S J. Clarke

In the non-codified realm of tunnel design there are issues which are sure-fire instigators of controversy. This paper presents a discussion regarding one particular issue which in the authors’ experience often results in comment and debate. This issue only forms part of the rock load assessment process, but it is specifically addressed with the intention of presenting a rational basis for design, which may result in broader acceptance within the tunnel design community.The issue considered relates to the characterisation of in situ rock stresses for the design of tunnel support in the Sydney Basin. A summary is given of the literature on the topic, with emphasis on the main sources of uncertainty and contention. A design approach is proposed, with particular focus given to the numerical modelling of in situ ground stresses and the approach used to ensure that the adopted stress regime is consistent with the assumed ground model. The resulting variability in the initial stress field is discussed and comparisons made to the test database.CITATION:de Ambrosis, A L and Clarke, S J, 2014. Characterisation of in situ stresses for tunnel lining design in the Sydney?Basin, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 247–252 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By R Cooksey

The Globe-Progress Mine is an open pit gold mine that is part of the larger Reefton Goldfields deposit located on the West Coast of New Zealand. The regional geology comprises a series of north to south oriented fold structures that have undergone post-deformation mineralisation. The structural geology within the mine itself is more complex, with major shears hosting numerous high-grade mineralised quartz shoots and splays that have been historically mined.The selective mining of ore within the pit is challenging due to the orientations of the hanging wall and footwall areas of the main Globe shear zone, the lithologies of these areas which range from highly brecciated and sheared material to competent mineralised host rock, and in the hazards presented by the numerous old historic underground workings. The coordination of drilling, modelling and excavation of the ore requires careful planning to maximise recovery whilst operating with the pit design boundaries.Grade control packages are custom designed to reflect the orientation of the footwall and hanging wall mineralisation. The shear material in the footwall zone dips between 60° and 70° and requires angled drilling whereas the footwall mineralisation is contained in shallow dipping quartz veins sub parallel to bedding and can be vertically drilled to best intercept the mineralisation. Ore excavation is directed so that the contact between the footwall and hanging wall is mined in the correct direction so that any non-visual ore contacts can be safely mined and that the ore-waste dilution is reduced.The ongoing grade control and selective mining of the Globe Progress deposit continues to deliver high grade ore for processing by ensuring that waste and dilution of ore is reduced and that recovery is maximised.

Aug 22, 2011

By A N. Kusnanto, D Sims, L Henim, S Crispin, J Hertrijana

The high sulfidation Purnama Au-Ag deposit located on the Indonesian island of Sumatra entered production in mid-2012 following a two-year program of construction and development. Discovered in 1997 following a regional stream sediment geochemical sampling program by the Normandy Anglo Asia joint venture, it is the first and largest deposit in G-Resource’s Martabe Project to enter production and is the centrepiece of a series of six deposits totalling 8.1 Moz Au and 73.8 Moz Ag in Mineral Resources (G-Resources, 2013a).In 2011 investigation into the controls of high-grade mineralisation in isolated parts of the deposit identified a potentially significant mineralisation style which had not been previously recognised or accommodated in the resource model. An extensive investigation of core and logging data followed to confirm the distribution of the somewhat unusual mineralisation style – a sedimentary-like cavity infill of very high-grade auriferous pyrite within the steep hydrothermal breccia feeders to the system. With the bulk of mineralisation located within the adjacent volcanic sequence and sandy-matrix phreatomagmatic breccia surrounding the feeders, the lack of constraint for high-grade intersections in the hydrothermal breccia zones had potential to significantly impact the mine plan in the lower sections of the planned pit through overestimation of local gold grade. Combined with new data emerging from grade control drilling and infill resource drilling in the pit, a program of reinterpretation of the deposit was initiated to update the geological and alteration framework underpinning the resource model. The result has improved the economics of the project and added metal to the Ore Reserve for Purnama.CITATION:Sims, D, Henim, L, Hertrijana, J, Kusnanto, A N and Crispin, S, 2014. Remodelling the Purnama deposit – an interpretation case study from G-Resources Martabe Project, Indonesia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 229–236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

Mt Todd lies towards the south end of the Pine Creek Geosyncline, sandwiched between the Cullen Batholith and the Edith Falls Basin, in an area of regionally metamorphosed sandstones, siltstones and shales. The Batman deposit, some 3 km west of Mt Todd is a sheeted quartz vein system hosted within greywackes of the Palaeoproterozoic Burrell Creek Formation (Finniss River Group). The gold-bearing quartz veins, trending 010¦-020¦ and dipping 60¦-70¦E, are commonly 0.5 to 5 cm wide and occur at intervals which are from 10 cm to 1 m apart. Gold tends to be restricted to the quartz veinlets and immediately adjacent country rock. Grade Control utilises two 4 m 'collar' samples which are collected from each 8 m production blasthole. The irregular distribution of the quartz veins and erratic gold mineralisation has resulted in a disseminated 'salt and pepper' type of gold occurrence, with only a poorly defined footwall. Delineation of ore and waste blocks for mining uses an approach which combines the smoothing effect of kriging with a pragmatic view of the raw data. Large ore blocks with simple geometry help to minimise mining dilution, reduce block variance and give good reconciliations to interpreted ore tonnes and grade. Daily mine face advance is reported against truck counts and provides continual comparison with budgeted production. All data processing uses Gemcom software, together with Lotus spreadsheets.

Jan 1, 1994

By S Farrokhpay, C Akop

Copper-gold-pyrite ore types with an elevated pyrite head grade utilise a sequential flotation circuit to recover initially a copper-gold concentrate with a pyrite-gold concentrate being produced from the tailing of the initial circuit.A simpler flotation circuit with lower operating and capital costs for treatment of such copper-gold-pyrite ores with an elevated pyrite head assay was sought in the described work. After characterising the ore, the objective was to apply bulk rougher flotation of both the copper minerals and pyrite for the copper-gold-pyrite ore at natural pH. Hence, no lime or other pyrite depressants were required in bulk roughing. The bulk rougher concentrate was upgraded in a cleaner circuit to reject non-sulfide gangue and then the resulting sulfide concentrate was separated by depressing the pyrite to produce two products (copper and pyrite concentrates, both having significant gold assays). A standard test with a sequential circuit was applied to the same ore for comparison.The chalcopyrite and pyrite losses in the tailing from the rougher circuit were the same for both bulk and sequential roughing (less than six per cent). In cleaning (bulk circuit), the effective pH for pyrite depression was 11.8–11.9; copper recovery was 70–75 per cent (grade of 15–20 per cent copper) and the sulfur recovery (pyrite product) was 80–85 per cent (grade of 34–36 per cent sulfur).These results approached those for the sequential circuit where copper recovery was 80–85 per cent (grade of 15–20 per cent copper) and the sulfur recovery (pyrite product) was 83 per cent (grade of 38 per cent sulfur).The observed effects of feed sizing on the liberation of minerals in the rougher feed are discussed. Options for improving the bulk circuit results are also considered. Importantly, the implications of various aspects of these findings for the bulk circuit are discussed with an industrial focus.CITATION:Akop, C, Farrokhpay, S and Johnson, N W, 2014. An alternative circuit for chalcopyrite-pyrite ores with elevated pyrite content in Cu-Au ore treatment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 407–416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By G Davison, C Rossimel, M Bouazza

Expanding rock bolts anchor within a rock mass more efficiently than non-expanding varieties. This is of great importance in weak ground conditions, where grouted friction bolts perform less efficiently than in good ground conditions. Filling a Split Set with demolition concrete has been shown to double the load-carrying capacity when compared to conventional use of Split Sets. This report details verification of these results by installing and pull-testing 14 Split Sets of varying grout conditions within in a fault zone. These Expanding Split Sets achieved loads double and triple that of ungrouted and normally grouted conventional Split Sets. A literature review and chemical analysis were conducted to understand the expansion process better. It was found that 20 per cent more calcium is included in expanding cement, which is responsible for its growth. Factors most affecting the expansion process were identified. Furthermore, the expansion rate of a bolt outside a borehole was measured and 6 mm of expansion across its diameter was found. The compressive properties of the cement were compared with other types, due to expanding cement becoming uncohesive after the expansion process is complete. When confined within a Split Set, compression testing demonstrated that this grout is just as strong and rigid as normal grout. Finally, the bolts were tested by shear and it was found that the Expanding Split Set (ESS) has a similar shear capacity to grouted Split Sets, which is 70 per cent higher than that of ungrouted Split Sets. These results enabled the mechanism for improved performance in weak ground conditions to be verified. Expanding grout will expand the Split Set into its borehole of varying diameter and lock it into place, creating increased friction and resistance to pull-out. This paper shows that ESSs can be a useful reinforcement technique in weak ground conditions.CITATION:Rossimel, C, Davison, G and Bouazza, M, 2014. An investigation of expanding split sets in weak ground, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 159–170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By G R. Hancock, J B. C Lowry, T J. Coulthard

A reconstructed landscape may exert long-term influences on its surrounds and behave in ways that may not be predictable given uncertainties regarding climate, soil and vegetation interactions (Evans, 2000). In recent years, computer-based landscape evolution models (LEM) have been used to assess potential and existing mining landscapes and their long-term geomorphic behaviour (Hancock et al, 2007; Hancock, Lowry and Coulthard, 2015; Tucker and Hancock, 2010).In this paper, we focus on the evolution of post-mining landforms, which are designed to include burial or encapsulation of mine-impacted areas and materials, including tailings, drains, spoil tips and other industrial architecture (Figure 1). At the Ranger Uranium mine in the Northern Territory of Australia, low-grade uranium ore, tailings, brines and other mine wastes will be buried at depth in the areas of the former pits and tailings storage facilities.The use of LEMs to predict long-term landscape evolution has several issues. These include that model predictions are based on the calibration and parameterisation of the model carried out using values determined from present day, or recent surface conditions. Furthermore, there is also the question as to how subtle perturbations or roughness on the DEM surface can produce alternative model results by randomly varying the elevations of the DEM surface.In this study we examine the effect on sediment transport rates and geomorphology for a proposed rehabilitated landform using multiple landscape realisations with increasing magnitudes of random changes in the DEM using the SIBERIA LEM (Willgoose, Bras and Rodriguez-Iturbe, 1991).CITATION:Hancock, G R, Coulthard, T J and Lowry, J B C, 2016. Use of landform evolution models to assess uncertainty in long-term evolution of post-mining landscapes, in Proceedings Life-of-Mine 2016 Conference, pp 67–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By A Scott, I Onederra

Most iron ores occur in mine benches as complex mixtures of lithologies and ore types. This significantly complicates their characterisation for both blast design and fragmentation modelling. A great deal of technical and research effort has been applied to the development of models to predict fragmentation from rock blasting. A number of quite useful engineering models are currently available to blasting engineers and consultants, and more sophisticated approaches using mechanistic descriptions of rock breakage continue to be developed and applied by researchers and explosives companies.The engineering or empirical models that are in more general use within the industry, such as the Kuz-Ram model, require appropriate data if they are to generate useful fragmentation predictions. Some of these models have reached significant sophistication and have made very useful contributions to both routine blasting operations and the exploration of new blasting paradigms. However, these models struggle to adequately deal with rock that is as complex as iron ore. This paper reviews the characteristics of the most successful blast fragmentation models available to the industry and discusses approaches to the derivation of suitable rock mass properties to adequately describe blast fragmentation in a range of iron ores.CITATION:Scott, A and Onederra, I, 2015. Characterising the blasting properties of iron ore, in Proceedings Iron Ore 2015, pp 481–490 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015