Search Documents

By A Holmgren, W Forsling

In the present study infrared attenuated total reflection (IR-ATR) was used to monitor the rate of in situ adsorption of heptyl xanthate on a layer of zinc sulfide synthesised on a germanium ATR crystal. The zinc sulfide surface was characterised using x-ray photoelectron spectroscopy (XPS). The absorbance of heptyl xanthate measured increased with increasing bulk concentration of the adsorbate up to an equilibrium plateau value corresponding to a fractional coverage of the surface sites of the substrate. For the adsorption from solutions of concentrations between 10-3 and 10-5 M, the rate of adsorption increased with increasing bulk concentration. At higher concentrations the measured absorbance should be corrected for the absorbance due to the concentration of xanthate in bulk solution. The present work provides a discussion of this correction. Assuming the adsorption stage to be rate-controlling and proportional both to the concentration of the adsorbing species in solution and unreacted surface area, a rate law governing this type of transient adsorption kinetics was derived. By means of absorbance data for the concentrations 0.1 and 0.01 mM, the rate constant of adsorption was calculated. From the initial part of a Langmuir adsorption isotherm, the absorbance at monolayer coverage and the equilibrium constant of adsorption could be estimated.

Jan 1, 2005

By J Loeb, D Thornton

Blast movement measurement is a key component of grade control, enabling mines to carry all of the precision involved in locating ore blocks, through a chaotic blast, to production. A monitoring system was developed about ten years ago so that mine operation personnel can measure three dimensional movement in every production blast. Research has shown that blast movement is always highly variable with a significant non-deterministic component. The consequence is that modelling will be inaccurate and therefore optimal ore recovery can only be achieved by direct measurement of blast movement.Three dimensional movement vectors are measured at discrete locations in the blast. If blast movement is only measured at one location in a blast pattern, data is severely limited and has all of the inherent inaccuracies of modelling a variable population. It is intuitive that the accuracy of defining the post-blast ore block mark-ups are proportional to the number of movement measurement locations, however increasing the number of monitoring locations causes increases to the direct operating costs of the mine.A cost-benefit analysis is used to explore the optimal number of monitoring locations. Using the method described in this paper, an automated selection of the number and location of blast movement monitors are analysed against the value of recovered ore compared to the control, for each trial.CITATION:Loeb, J and Thornton, D, 2014. A cost benefit analysis to explore the optimal number of blast movement monitoring locations, in Proceedings Ninth International Mining Geology Conference 2014 , pp 441–450 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By A Bossilkov

Although environmental and sustainable development reporting has now become widespread in the Australian mining and minerals processing sector, there remains a great deal of diversity in reporting contents and practice. Moreover concerns remain about the effectiveness of reporting for delivering the companyÆs business case for sustainable development as well as for communicating sustainable development performance to a range of external stakeholders. This paper therefore reviews the status of sustainable development reporting in the Australian minerals processing industry. Pertinent international and national developments are briefly captured, leading to a discussion of the framework for integrating sustainable development reporting with sustainable development management (as proposed by the World Business Council for Sustainable Development). This leads to a discussion of the results of a comparative review of sustainable development reports of a cross-section of eight Australian resource companies. Best practice elements are highlighted in regard to reporting on company context, governance, performance and assurance.

Jan 1, 2004

By S Joyce, Z Agioutantis, D van Zyl, D Shields

Over the past 15 years, the mining industry has begun to incorporate the concepts of sustainable development and sustainable mining practice across the life cycle of mineral operations. This requires addressing economic issues, community impacts and concerns and environmental protection, and is captured in part by the phrase ‘design for sustainability’ (McClellan et al, 2009). Over the same period, the industry has seen a gradual decline in ore grades for many mineral commodities. As a result, large volumes of tailings and mine waste rock are being produced around the world, and it is expected that the annual production volumes of these materials will increase, even if there is not a significant change in the demand for materials.Another related thread of change has been the realisation that societies need to move away from linear economies (raw materials, production, consumption, disposal) towards more circular ones. This will help societies become more resource efficient, which is defined by the United Nations Environment Programme as reducing the total environmental impact of the production and consumption of goods and services, from raw material extraction to final use and disposal. The goal is to create more with less and deliver greater value with less input. Circular economies require thinking in terms of the waste hierarchy (reduce, reuse, repurpose, recycle, recover, landfill).The challenge is that the waste hierarchy was originally designed to address embodied mineral content in products rather than mine waste and tailings generation. It will need to be reconsidered in a mine life cycle context, focusing on a value-based conception of waste (Van Ewijk and Stegemann, in press).In parallel to these changes, it has remained an imperative in the mining industry to dispose of these waste materials as economically as possible while protecting the environment. Single handling of these materials has been the main target, which reduces the life cycle costs of their management but may make reuse of waste and tailings technically more difficult or economically infeasible.This presentation explores a rethinking of the large volume earthen material waste issue at mines. The underlying theme is that some or all of these materials can be valuable resources for the future that can positively contribute to sustainable development. These resources can offer economic gains to firms, communities and societies; contribute to environmental well-being; enhance social interactions with the previously mined landscape if handled properly; and, with proper policies in place, reduce governance commitments. Each of these topics will be briefly explored. This will be followed by a discussion of approaches to manage design and operations to allow future resource recovery.CITATION:Van Zyl, D, Shields, D, Agioutantis, Z and Joyce, S, 2015. Waste not, want not – rethinking the tailings and mine waste issue, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 7–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By R H. Sibson

Magmatic and/or hydrothermal fluid systems in island or mountain arcs self-organise to critical states subject to perturbation by changes in the regional stress, which plays a controlling role in the containment of overpressured fluids. Whether the magmatic arc is under compression (eg Andes, northern Honshu) or extension (eg Taupo Volcanic Zone, New Zealand) is a key factor controlling the ease of magmatic or hydrothermal fluid ascent. Abrupt changes in the stress regime have the potential to induce major episodes of fluid redistribution. Large earthquake ruptures along plate boundaries may induce such changes over broad areas, also contributing to fluid redistribution by renewing fault permeability along the causative rupture zone or reactivating distant fault-fracture permeability by shaking from radiated waves. High-resolution geophysical investigations of active arc systems and the subduction thrust interface underlying their fore-arcs reveal repositories of overpressured hydrothermal fluids. In active magmatic arcs under compression such as NE Honshu or Cascadia, there is evidence for a heterogeneous distribution of overpressured hydrothermal fluids in the middle-to-lower crust trapped around the base of the upper crustal seismogenic zone. Investigations of the subduction thrust interface responsible for great (Mw = 8.0) ‘megathrust’ earthquake ruptures has revealed in some instances (Cascadia, SW Japan) the existence of a belt of non-volcanic tremor (NVT) with accompanying slow slip episodes defining the base of the megathrust interface at 40 ± 5 km and 350°C??-??550°C. Aqueous fluid at these depths is likely derived from dehydration reactions accompanying the basalt-eclogite transition in subducted oceanic crust. NVT sequences in the hanging-wall above the interface may be defining migration pathways into the overlying crust.The potential for eruptive episodes in magmatic arcs and redistribution of hydrothermal fluids is assessed in the light of the stress changes that followed the 2011 Mw9.0 Tohoku subduction thrust rupture which extended along strike for over 500 km and down-dip for over 150 km, with maximum slip of c 50 m.

Aug 22, 2011

By A Scrase, J Brereton

The Latrobe Valley is located approximately 150 kms east of Melbourne. Within a very small area there are 3 large brown coalmines and associated power stations, 3 large towns, and numerous smaller towns in the vicinity. The mines have been generating power for Melbourne and surrounds for the last 100 years, with two of the mines being owned and operated by the Victorian Government (State Electricity Commission of Victoria) prior to privatisation in the 1990s. All three mines were privatised with the expectation that the mine voids would be filled with water to become pit lakes, as the final landform/rehabilitation solution (Hazelwood Mine Fire Inquiry, Teague and Catford, 2016). It could be argued that until relatively recently, this was largely expected, by government and industry, to be the rehabilitation solution for managing the two key risks associated with the sites:  The geotechnical stability of the mine pits.  The prevention of fire – through covering coal batters with water. Transitioning away from mining economies requires collaborative, regional, innovative thinking with a multitude of stakeholders, from a wide range of government departments, industry, First Nations people and broader community. Closure planning and rehabilitation activities require a range of skills and experience, such as, closure planning, various scientific and engineering disciplines (pit water quality modelling, geochemical modelling, cover design, landform design, contaminated site etc), civil engineering, demolition etc. Some of these skills are similar, such as financial modelling, stakeholder engagement, contract and project management. But the majority are different to those required during the operational phase of a mine. These closure skills can also be lacking within government, with Departments more familiar with monitoring and compliance activities associated with operational facilities. Some key aspects that appear to be critical to planned successful closure are:  Collaborative regional and localised planning, with industry, government, community, First Nations and other industry, business leaders and entrepreneurs all involved in providing a smooth transition away from mining.  Well-defined and known regulatory pathways to achieve mine licence relinquishment assists in encouraging investment.  Appropriately skilled and experienced government and industry personnel.  Mining companies, who are committed to closure planning and provisioning from the earliest point in project planning.  Mine employees who are appropriately skilled and experienced in mine closure planning and implementation with access to all the relevant technical expertise required for the project. Areas like the Ruhr Valley in Germany provide good some examples of smooth processes that facilitate mine economies transition into new economies (World Resources Institute (WRI), 2021).

Aug 2, 2023

By P Velletri, N Gaylard

The management of wear surfaces in mining operations has remained largely unchanged since the inception of mining. Sacrificial wear liners are installed on the inside of chutes, hoppers and other equipment used to transfer bulk ore to protect the asset from abrasive wear caused by the flow of material. These liners are generally replaced at fixed intervals which may be determined based on historical wear rates or may be driven by other maintenance requirements for that asset. This approach does not always yield satisfactory results, especially for critical assets where the impact of downtime on production can be substantial. For such assets, a condition-based maintenance strategy has the potential to significantly increase productivity and reduce the total cost of ownership associated with the asset. However, for such a strategy to be successful, timely information on the actual condition (remaining thickness) of the wear liners is essential. This paper describes the development and implementation of a wear monitoring system that can be used to remotely and continuously report on remaining liner material thickness in real time. It details some of the challenges that were overcome when developing the system, including the design of a patented thickness measuring system that can be used in a variety of liner materials and is tolerant to the presence of ore on the wear surface. The paper also explains how a cloud-based approach enables data from the wear sensors to be integrated into external systems such as a data historian, which has been demonstrated through a collaborative project with one of the largest iron ore producers in the Pilbara. This ability to combine real time liner thickness information with other data sources, such as throughput, provides the foundation for the transition to a condition-based maintenance strategy.

Nov 8, 2021

By M Freeman

In a visionary move, the Planning Commission and the Ministry for Planning in Western Australia decided to invite three extractive industry quarry operators, local government councils and State Government departments (Minerals and Energy, Environmental Protection, South West Development Commission) to contribute jointly to study the impacts of blasting on areas surrounding basalt quarries in the Bunbury region of WA. The results of the study will help establish suitable zones in which land uses will be controlled under a proposed Greater Bunbury Region Scheme and in local planning schemes, to minimise conflicting land uses. This paper discusses the blasting program conducted to characterise and model the vibration behaviour of the rock under the effects of pilot-scale and full production blasting, and highlights some of the benefits achievable when a thorough blasting impact program and assessment is conducted at the planning stages of land-use establishment.

Jan 1, 2001

By Szwedzicki T

In recent years substantial advances have been made in the field of geomechanics. Staff at the Western Australian School of Mines (WASM) are keen to see that such advances continue and that the mining industry in Australia can take full advantage of such developments in a timely manner. WASM views mining geomechanics in its broadest sense, as being concerned with the characterisation of the physical properties and the behaviour of earth materials (soil, rock and water) and openings as mining proceeds. Aspects such as, soil and rock improvement techniques for difficult site conditions and the rock breaking processes, are also considered to be an integral part of mining geomechanics. This paper indicates the inter-relationships between the various areas within the field of geomechanics and the strong reliance of all of these areas on site specific engineering geology.

Jan 1, 1992

By D Hatton, S Wilson, F Orrante, M Taghimohammadi, F van der Walt, N Arslan, M Westcott

"Cayeli Bakir Isletmeleri is an underground copper-zinc mine in turkey. The ore is highly variable with feed grades ranging from 1–4 per cent copper and 1–10 per cent zinc. Due to this variability, ore characterisation and blending strategies are crucial for performance optimisation.This paper presents a case study for a multidisciplinary approach to process optimisation, integrating Geometallurgical and advanced control methods to achieve optimised plant performance. The results from comprehensive metallurgical tests and surveys were used to develop a mathematical model utilising SGS’s Integrated Geometallurgical Simulator® (version number 2.5.24.0). The model was employed to determine the most appropriate operational settings required to ensure that optimised grades and recoveries are achieved for each ore type.SGS’s Modular Expert Technology (MET) expert system was then implemented to target these optimum operational ranges utilising online grade and froth velocity measurements. The successful conversion and deployment of the modelled process parameters into an expert system has resulted in significant improvements in overall recovery and circuit stability.Citation:Arslan, N, Westcott, M, van der Walt, F, Hatton, D, Taghimohammadi, M, Orrante, F and Wilson, S, 2016. A Multidisciplinary Approach to the Optimisation and Control of a Copper-zinc Grinding and Flotation Circuit, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 115–122 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By V Pfannenstiel

The United States (US) coal mining industry has been working under comprehensive planning, operating and rehabilitation regulatory requirements for nearly 35 years. The public desire for environmental protection during mining and rehabilitation following mining to achieve post-mining land use and sustainability goals has been a major factor and continues to influence the process. Mining companies have evolved operations to achieve outcomes that address the desired goals and regulatory requirements cost-effectively and successfully. Over the 35 year regulatory period, requirements for more diverse topography, specialised revegetation communities, landform stability and assured sustainability have increased and become more complex. These challenges are effectively met by maximising integration of mine planning and operating with the rehabilitation process. Rehabilitation is then implemented in a more timely and efficient manner and with effective results that achieve desired outcomes, commonly with added value. Peabody Energy (Peabody) has taken this approach in its US operations and this paper discusses an integrated approach and illustrates learnings and results with examples from several of its western US operations.CITATION:Pfannenstiel, V, 2012. Integrated planning, mining and rehabilitation for effective results and sustainable land use - A western United States perspective, in Proceedings Life-of-Mine 2012 , pp 219-232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By D J. Bradshaw, B Lottermoser, A Parbhakar-Fox

"Best practice for acid rock drainage (ARD) risk assessment still relies solely on the geochemical properties of sulfidic rocks and mineral processing products, despite the fact that a rockÆs tendency to produce acid also depends on mineralogy and texture. Consequently, there are a plethora of geochemical tests routinely utilised by the mining industry to predict ARD formation. Due to limitations associated with these tests and their relatively high costs, analysis of recommended best practice sample numbers is rarely achieved, reducing the accuracy of waste management plans. Our research addressed this through examining the application of geometallurgical data for predicting acid formation, and led to the identification of potential environmental geometallurgy indicators.Samples obtained from an iron-oxide copper gold deposit were subjected to the geochemistry-mineralogy-texture (GMT) approach, an improved methodology for classifying acid forming potential. GMT results were compared against geometallurgical and assay data sets to evaluate: relative carbonate content measurements (measured by HyLogger) and identify how these could be used to calculate effective acid neutralising capacity mineral hardness (measured by EQUOtip) to determine application of this data for calculating lag-time to acid formation opportunities to automate the acid rock drainage index (ARDI) using classified images produced by a GEOTEK logger and automated microscopy.Links between the GMT approach and geometallurgical data sets were identified. Classified mineralogy data has application at stage one, HyLogger and EQUOtip at stage two and computer-based ARDI evaluations of classified images at stage three. Through such integration, ARD characterisation costs can be reduced, with value added to geometallurgical data sets. Furthermore, deposit-wide ARD domaining is possible, and acquisition of total-orebody knowledge more likely. Through adoption of this environmental geometallurgy approach, a better informed waste management plan can be formulated, allowing for best practice ARD sampling in a more cost-effective manner.CITATION:Parbhakar-Fox, A, Lottermoser, B and Bradshaw, D J, 2013. Cost-effective means for identifying acid rock drainage risks - integration of the geochemistry-mineralogy-texture approach and geometallurgical techniques, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 143-154 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By S Grimsey, E Janetzki, J Emery

Floor failure on the longwall face is a complex problem due to the dynamic interaction between the surrounding strata and powered roof supports involving multiple variables. It can also be highly problematic and costly when not well understood as there are significantly less remedies available post event. This was the early experience at the case study mine where significant lost time was incurred due to unplanned delays in the first two panels. To detect and prevent such occurrences is clearly the best approach, hence a tool to predict both floor failure occurrence and magnitude prior to mining was developed. Several parameters were determined as the key drivers for the failure events that had been experienced at this site. These parameters were, in list of influence from highest to lowest, material strength, retreat rate and the presence of water. The parameters were evaluated using a semi quantitative risk rating system ‘Heave Risk’ and given a weighting per their apparent influence. This ‘expert system’ methodology was selected as the use of risk rating systems in underground coal mining is well established. The heave risk model was first applied to previously mined panels. It accurately identified all areas of known major floor heave, with clearly defined areas of low and high risk apparent. The heave risk model was then used prior to mining and evaluated post mining based on observed conditions. It was found to also be highly accurate for prediction. The variability of each parameter and its influence on the overall risk rating is illustrated and discussed.

Nov 29, 2022

By H Ishikawa, S Palaniandy

The gravity-induced stirred mill such as the TowerMill is an energy-efficient grinding solution used in secondary, tertiary, and regrinding duties in the mineral processing concentrator. The interest in this technology is emerging, with more than 300 mills installed globally in various grinding duties and commodities for the last 30 years. Although the technology is matured, there are still opportunities for improvement and the development of new knowledge to improve its circuit energy efficiency and reduce water consumption. Recent studies show that a combination of stress intensity, ore hardness, slurry density, and mill feed configuration can be used to evaluate the performance of the grinding circuit. A recent pilot-scale TowerMill test work at various stress intensities shows that a lower operating work index and size-specific energy were achieved at higher agitator tip speed and using medium size grinding media. These outcomes were confirmed through several site trials. A smaller 17 mm grinding media has reduced the operating work index and size-specific energy by 18 per cent and 11 per cent, respectively, compared to the 20 mm in a magnetite concentrator. Moreover, the conversion from top feed to bottom feed configuration has reduced the operating work index and size-specific energy by 13 per cent and 37 per cent, respectively. The circulating load was reduced by 34–38 per cent, leading to a reduction in the dilution water consumption in the hydrocyclone feed sump by 20 per cent. A variable frequency drive offers flexibility to change the stress intensities on the TowerMill, where a 35 per cent reduction in specific energy was achieved when the ore became soft. This paper explores the potential design and operating strategies that can be implemented to enhance the energy efficiency, reduce water consumption and reduce CO2 emissions in the circuit and finally evaluate its impact on the total cost of ownership.

Aug 24, 2022

By L B. Zhou, Q Wang

The present discussion focuses on the developmental directions of eco-restoration of acid mine waste rock dump, by using acid mine waste rock of Shuilong Mountain as an example. Based on the analysis of site factors, the current slope ecological restoration technologies of domestic and international and local practices have been integrated into the eco-restoration of acid mine waste rock in Shuilong Mountain. A set of suitable slope Eco-restoration technologies have been formulated locally for acid mine waste rock of Shuilong Mountain, which include establishing green barrier, implementing ecology buffer zones, selecting suitable plant species and combined seeding and tube-stock planting. It aims to restore the plant ecosystem to a near natural state, in couple with slope stabilisation and soil remediation.CITATION :Wang, Q and Zhou, L B, 2012. Projection of ecological restoration of acid mine waste rock of Shuilong Mountain at Dexing Copper Mine, in Proceedings Life-of-Mine 2012 , pp 305-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By C Young

In the vast expanse of Western Australia’s mining sector, a critical issue has come to light: many mining operations overlook the power of a Broad-Brush Risk Assessment (BBRA) to uncover their critical risks. This oversight has led to a cascade of challenges, where some mining endeavours find themselves grappling with: - Unidentified and unmanaged fatal risks, casting a shadow of uncertainty and heightened compliance risks. - A bewildering landscape where the concept of critical risks remains enigmatic, with some mistaking the risk register for the BBRA. - A fog of confusion surrounding the guardianship of these critical risks, leaving safety responsibilities blurred and undefined. Yet, the solution lies within our grasp. An effective BBRA empowers organisations to: - Pinpoint with unwavering certainty every ‘true’ critical risk. - Clarify ownership for each critical risk, ensuring accountability and swift action. - Create a prioritised roster of critical risks, illuminating the path to safer operations. - Lay the foundation for essential follow-up actions like bow-tie analysis, the identification of critical controls, and the fortification of the safety and health management system. Join us in this presentation, where we delve into the heart of an industry-leading BBRA process. Discover practical insights that will enable your organisation to craft and implement BBRA strategies, bridging the gaps in your journey toward preventing fatalities and fortifying safety protocols.

Apr 16, 2024

By J A. Braithwaite

Social licence to operate is not a new concept for the mining industry, referring to stakeholder approval or acceptance for the activities and impacts of a project, company or industry. It is intangible, dynamic and non-permanent, hence it needs to be earned and then maintained (Thomson and Boutilier, 2014). It has also been argued that social licence extends beyond building approval or acceptance, into engagement for long-term development (Owen and Kemp, 2012).There are many examples where stakeholder opposition – or withdrawal of social licence – have increased capital and operating costs, extended schedules and impacted reputation. At its extreme, the withdrawal of social licence to operate can also contribute to or be the catalyst for mine closure.The key benefit of obtaining a social licence is a reduction of risk. Stakeholder support and advocacy, as well as the implementation of social performance programs that contribute to social licence, can be beneficial in terms of schedule, costs and other benefits.While decisions to close a mine are generally driven by resource availability or economic conditions, the social, economic and environmental legacy remaining post-closure is of importance to many stakeholders. With a number of significant mines now approaching closure within Australia, we are seeing heightened community concern about the economic and social impact of mine closure and the success of land rehabilitation. So how does the concept of social licence to operate extend into the closure phase of the mining life cycle?CITATION:Braithwaite, J A, 2016. Social licence to close?, in Proceedings Life-of-Mine 2016 Conference, pp 176–179 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

A combination of the needs of business, employee desires and safety and health considerations is stimulating increasing attention to the time spent by people at work and the timing of that work. Particularly we are seeing: - innovative work schedules for 24-hour mining businesses; and - response from industry to accommodate the needs, even the desires, of employees in return for systems which are more productive and more capital efficient. There appears to be an evolutionary trend for business management to become more sophisticated and responsive to the need for achieving close to best cost work schedules to sustain continuous improvement. The underlying motivating forces driving this trend for improved techniques in organising attendance at, and time spent at work, is the seemingly inseparable combination of technological advance and ever-increasing accumulation of capital. The mining industry has not remained untouched by this thrust for ever-increasing need for best use of labour, to adopt advances in technology and to provide attractive opportunities for putting accumulated capital to work. An essential component of this on-going thrust is a substantial effort by the mining industry to improve the performance of labour by providing most-productive work schedules.

Jan 1, 1996

By F D Durao, Muge F. H, Rogado J. Q

In the scope of the project named CAPUME II (EEC BRITE/EURAM contract - project MA2M-CT90,-0042(SMA)) for the development of an integrated mine planning system for underground mines, two of the main tasks were the development of a short-term mining planning procedure (module) and a numerical simulator of the mineral processing plant of Pirites Alentejanas - PA. The short-term mining planning module defines the mining sequences by solving a constrained minimisation problem. The ore grade variability is the objective function subject to the geometrical constraints of the mining method and to the maximum of `internal blending'. The optimisation problem is solved by applying a dynamic programming algorithm. The plant simulator is an essential tool of the planning system allowing the preview of metal grades/recoveries of copper, lead and zinc of concentrates streams, given the corresponding metal assays of the run-of-mine ore, defined by the short-term mine planning module. This way, the management can plan the short-term mining operations (the weekly sequence of exploration blocks and the internal planning) in order to fulfill given required conditions, based on a shipment schedule and on a purchaser's formula. In this paper, after a short description of the short-term mining planning module and of the simulation package named SIMUL, a synthesis of the main model development steps and the results of some simulation runs are presented and discussed.

Jan 1, 1995

By G M. Volkmann

Pipe umbrella systems have effectively been used as an additional support system in the working area in weak ground conditions during the last decades. Thus, a considerable number of applications accounts in urban tunnelling with shallow overburden. However, this support system is also successfully used when a tunnel alignment crosses fault zones, sediments, moraines or talus with overburdens from shallow to deep. The pipe umbrella support system itself is termed differently worldwide – synonyms are canopy tube umbrella method, umbrella arch method, or long fore-poling method.One main reason for the increase in application is that this support system closes cost-effectively the gap between reasonable, normal supported tunnels and tunnels supported with more expensive special techniques like horizontal jet-grouting or ground freezing. By using this system, many projects can be built more cost effective without decreasing the common level of safety.The pipe umbrella construction method is pretty young, so the knowledge about this system has been intensely researched in the last decade. This led to an enormous increase in understanding the interaction between support system and surrounding ground, the mode of action, and the important details for construction.Pipe umbrella support systems are applied in difficult ground conditions, so a special developed measurement arrangement was used to observe deformations ahead of the working face during tunnelling. The evaluation of collected data sets identifi ed that cased-drilling systems have clear advantages compared to predrilling systems during the installation process in weak ground conditions. This may become important depending on project requirements, so this difference must be considered in design as well as in the tender document specifications.

Mar 8, 2011