Search Documents

By W Baguley

Attritioning has been a method of improving mineral extraction for over 60 years, however it is only recently that an understanding of the mechanism employed and the improvement in efficiency that have been achieved.The paper will discuss these improvements and how to overcome the problems that have been raised. At present there is a dearth of information on the correct design and operation of these machines.The paper will address these issues as well as fluid on the Zeta potential, micro shear, retention residence time and pilot plant operation.A study on the hydrodynamics of attritioner operation has been identified and will be discussed.Surface chemistry, clean lines of attrition material and the treatment of fines significant advances in the understanding of attritioning highlighted.CITATION:Baguley, W, 2013. Attrition scrubbers, in Proceedings MetPlant 2013 , pp 229-246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

In this paper is given a description of the flotation plant recently erected by Broken Hill South Limited at the South Mine, Broken Hill, N.S.W. It has been built on the site of the old flotation plant, which was described in a previous paper published by the author. The present paper is supplementary to the former paper in that it replaced the following sections thereof, namely, those from end of the second paragraph, page 269, to the end of the first paragraph page 282, and from the end of the second paragraph, page 284, to the end of the third paragraph, page 302.The roll crushing, fine grinding, gravity concentration, filtration, disposal of products and sampling in the new plant are the same as described in the above mentioned paper.The reconstruction of the flotation section, described herein, completes the reconstruction and modernisation of the treatment plant which was begun in 1928. A description of these earlier alterations has already been published in the Proceedings of this Institute.

Jan 1, 1935

By D M. Silva, J C. Alves

According to the literature, material transportation represents 50 per cent of the operating costs for an open pit mine. In this context, this paper proposes a multistage approach for dynamic truck dispatching in real open pit mine environments, implemented in the commercial package SmartMine®, marketed by Devex SA. The first stage of this approach defines the optimal number of trucks that maximises the tonnage production by means of a robust linear programming model, which considers the operational constraints of a real mining process. The second stage uses a dynamic dispatching heuristic joining computational simulation and multicriterion optimisation techniques for decision making for truck dispatching. Another relevant contribution of this work is the publication of realistic instances collected from a dispatching system managing an iron mine, containing information about the hauling and loading fleet, the equipment situation when the working shift starts, cycle times, the time line of special occurrences (such as equipment stoppages and loading equipment reallocation in order to satisfy the mine planning) and the tonnage produced. These instances were generated with the purpose of submitting the method to the test of a real situation that considers the uncertainties existing in the process studied. The proposed approach was validated by means of a discrete event simulation model applied to the previously designated instances. Using this multistage approach as a mechanism for dispatch decision making, it is shown that the haulage fleet productivity increased when compared with the real values reported from the instances. These results are important because they show that the proposed approach generates efficient dispatch decisions for trucks operating in a real environment, reducing operating costs, increasing production and making the mine more competitive.

Sep 26, 2011

By R J. Beazley, M C. Woods

"The International Cyanide Management Code (the Code) is a voluntary industry program for gold miners and associated cyanide transporters and cyanide producers. By becoming a signatory, a company commits to follow the CodeÆs principles and implement its standards of practice.Signatories are required to undergo an initial certification audit within three years and a recertification audit every subsequent three years. Recertification audits evaluate compliance over the preceding three-year period. This approach presents a number of challenges. Golder Associates has undertaken in excess of 75 initial certification audits and 25 recertification audits; more than any other audit firm. This paper outlines some of the challenges identified and lessons learnt from the recertification audit process. Central to the process is the challenge for organisations to maintain commitment to compliance over the full three-year period and effectively address deficiencies or non-conformances that may have occurred during that period in a prompt manner.The International Cyanide Management Institute (ICMI) provides guidance in evaluating deficiencies or non-conformances, which requires consideration of the æcauseÆ, ædurationÆ and æongoing compliance effortsÆ and an assessment of the concept of ægood faithÆ in response actions. Golder AssociatesÆ experience with the recertification process highlights some common deficiencies with Code compliance programs, such as: system breakdowns (leading to ineffective communication between departments or loss of information) exceedance of discharge limits inadequate inspections, maintenance activities and associated record-keeping.Such deficiencies can be attributed to: personnel changes organisational changes or structures management systems (eg integrated or standalone) awareness and interpretation of Code requirements transparency of management decisions with Code implications.We have identified that ongoing programed assessment is an effective strategy in maintaining Code compliance.CITATION:Beazley, R J and Woods, M C, 2013. Cyanide code recertification - the three-year challenge, in Proceedings World Gold 2013, pp 247-254 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

By P J. Cullen, B P. Banerjee, S Raval

Continuous monitoring of mining impacts on the surrounding environment is a necessary sustainability criterion. Traditional monitoring approaches such as in situ sampling and airborne and satellite-based remote sensing have several limitations. Over the past few decades, unmanned aerial vehicles (UAVs) have evolved into popular platforms for remote sensing. UAV-based remote sensing has been successfully applied in different sectors, including agriculture, forestry, urban environments and disaster management. However, the potential of UAVs for mine environmental monitoring has not yet been fully established. This paper envisages the use of UAVs and sensor systems to monitor the environment of future mines.CITATION:Banerjee, B P, Raval, S and Cullen, P J, 2015. Unmanned aerial vehicles for mine environment monitoring, in Proceedings Third International Future Mining Conference, pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

Societal influences, needs, and uses for recyclable materials are becoming increasingly important business and economic factors in the traditional natural resource companies. Several metals (such as steel, aluminium, zinc, lead and cadmium) are amenable ro recycle which eliminates solid waste generation and decreases the depletion of natural resources. In recent years, the non-ferrous industries have begun to recycle more materials and the next decade will see even larger recycle efforts. In addition to the traditonal recyclable materials, existing metallurgical plants are, or should be, able to handle and recycle materials viewed as 'hazardous'. Unfortunately, some national and regional regulations hinder, and in some cases prevent, the recycling of certain materials. Zinc Corporation of America (ZCA) is currently the largest producer of zinc metal in the USA and one of the world's largest producers of value-added zinc products. Over the last few years, ZCA has become one of the world's largest recyclers of zinc from various diverse materials. ZCA considers these recyclable materials as valuable 'land mines' that provide economic alternatives to the depletion of natural resources while serving society in the minimisation of solid waste disposal. Using the current production facilities of ZCA as a model, this paper overviews the recycling of zinc-bearing materials with special emphasis on: 1. the amenability for recycle within ZCA's pyrometallurgical and hydrometallurgical operations, 2. the quantities and economics of recycle, 3. the problems of recycling hindered by current national and regional regulations, 4. the concepts of total recycle rather than just recovering zinc while generating a modified solid waste, and 5. the motivators for recycling.

Jan 1, 1993

By T Kojovic

"The index A*b, determined from the Julius Kruttschnitt Mineral Research Centre (JKMRC) drop weight tester (DWT) results, has become well-known in the mining industry as a reliable measure of ore hardness in impact or crushing, having the inferred units of t/kWh. This index evolved from a long history of comminution studies at the JKMRC, including the development of the now superseded JKTech twin-pendulum, the industry standard JK Drop Weight Tester (JKDWT) and the faster alterative JKMRC rotary breakage tester (JKRBT). A reduced version of the DWT, the semi-autogenous grinding mill comminution test (SMC test®), also provides estimates of the A*b though the testing of only one particle size at five specific energies. Experimental determination of A*b using the above devices/tests requires samples, with sufficient mass, to be sent to designated laboratories, registered to conduct such tests. This protocol is fine for bankable and commercial testing, where material characterisation data is used in conjunction with machine specific data in modelling and simulation, and power based calculations. However, for comparative testing, where results are required at the time of sampling (eg for plant troubleshooting or spot-surveys), or for rapid ranking of geometallurgical samples, these existing tests simply do not provide a timely, viable and cost-effective solution. In order to address this critical void in the realm of comparative testing, a new device has been developed, exploiting a central feature of single particle impact testing – that the A*b can be reliably estimated using one precise low energy test. This device, for which a patent is currently pending, called the HIT (Hardness Index Tester), has been precision engineered to allow users to break narrowly sized fragments at a set specific energy, in a safe and easy manner. The manufacturing materials have been chosen carefully to ensure compatibility with the intended use and portability to any site, whilst minimising cost. The device is supplied with a novel quality assurance / quality control (QA/QC) feature, to ensure that the targeted potential energy is consistently delivered. The product from the HIT breakage test can be quickly sized using a single screen to determine the mass per cent undersize, from which the A*b index is calculated directly at site – eliminating the need to send the raw data off-site for analysis. On presized fragments, a single test using 20 fragments takes less than five minutes to complete, and the results are immediately available. The HIT is currently being tested at a major mining laboratory in the US and the results to date have proved it can deliver on all fronts. This paper describes the new prototype device, which offers users a low cost in-house mechanism for estimating the A*b at any mine site, with potential applications on fragments up to 25 mm from drill core, blast chip rejects or the grinding circuit feed. It also outlines the results of field tests carried out by an objective third party mining group and compares the results with those from current industry standard tests conducted on the same material.Citation:Kojovic, T, 2016. HIT - a Portable Field Device for Rapid Testing at Site, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 9–16 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By D Davis

The prediction of ground-borne noise levels from tunnel construction activities requires knowledge of the input vibration forces from the vibration source(s) into the cutting face, knowledge of the vibration transmissibility through the surrounding medium, and knowledge of the receiver building’s vibro-acoustic response. The conversion of this vibration energy into sound pressure within the receiver building depends upon the vibration coupling of the soil and the building’s foundations, the structure’s response including floor-to-floor attenuation and amplifi cation due to resonance, the radiation effi ciencies of the internal structural elements, and the room’s acoustical properties. Beginning with a known input vibration spectrum at the cutting face, it is possible to predict the resultant ground-borne noise levels within a receiver building using either analytical and/or empirical techniques, or by numerical modelling. This paper presents an overview of the various methods available to estimate ground-borne noise levels from tunnel construction activities and discusses the advantages and limitations of each.

Mar 8, 2011

By N L. Turner, D J. Robinson, A J. McFarlane, N M. Chapman, L L. Kuhar, R L. Meakin, R Martin

A number of geometallurgical tests have been developed within the AMIRA P843A Geometallurgical Mapping and Mine Modelling (GeMIII) project, an interdisciplinary collaborative research project involving four research groups and over 20 global mineral companies. Researchers at the Commonwealth Scientific and Industrial Research Organisation (CSIRO) have been focusing on the development of predictive hydrometallurgical indices for the GeMIII project via rapid, small-scale, cost-effective tests and protocols for comparative ranking of attributes relevant to leach performance. One of the focus areas has been the development of a leaching scheme for determination of the mineralogical deportment of copper in a large number of samples for geometallurgical applications.Various leaching schemes have been used over the last 20 years to identify the mineralogical deportment of copper. Typically, weak sulfuric acid and cyanide are used to target copper oxides and æsecondaryÆ copper sulfide minerals, covellite, chalcocite and bornite, respectively. Residual copper is assigned to chalcopyrite and/or bornite. Adaptations of this scheme have included the use of a weak organic acid to target oxides or ferric sulfate to target secondary copper sulfides. Testing of the weak acid/cyanide scheme in the GeMIII project using head and residue QEMSCAN mineralogical data analysed with a statistically reliable comparison method indicated that the inferred mineralogical deportment from various leaches could differ markedly from the theoretical or assumed value. Based on this initial work, test development and leach tests on samples from multiple sites has resulted in the development of a scheme to target copper oxides, chalcocite, covellite, bornite and chalcopyrite. This paper presents results from leach tests conducted on a large sample suite from two pits in a Cu-Au ore deposit with results calibrated using mineral liberation analyser (MLA) mineralogical analysis. This study has assisted in the development of a protocol for determining the mineralogical deportment of copper in a large number of samples for geometallurgical applications.CITATION:Kuhar, L L, McFarlane, A J, Chapman, N M, Meakin, R L, Martin, R, Turner, N L and Robinson, D J, 2013. Calibration and testing of a geometallurgical leaching protocol for determining copper mineralogical deportment, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 177-186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By F C. D Michelin

Blast fumes are a significant health risk to underground workers, containing several dangerous gases such as carbon monoxide (CO), nitrogen oxides (NOx) and ammonia. To ensure safe working conditions, workers are not normally allowed to re-enter a mine until the gases are cleared. To predict if gases can be cleared efficiently, simulations can be performed to estimate the gas levels following a blast. For accurate modelling, a calibrated airflow simulation is required in addition to blast-specific parameters such as the yield rate (representing the amount of gas released per kg of explosive) and the dispersion factor (representing how quickly the gases can enter the air stream from the explosive site). Those parameters are not easily determined, as they will vary from blast to blast. Many post-blast gas recordings on mine sites were studied and the correct parameters were determined to ensure an accurate gas simulation. The variability of the results was then analysed and correlation to known parameters is suggested. Finally, recommendations on how to determine the correct parameter are presented.

Oct 12, 2022

Using Dynamic Simulation Throughout a Process Plant's Life Cycle

Sep 13, 2010

By M Chen, G H. Wang, J R. Zhou, P Yan, W B. Lu

Blast vibration analysis is one of the important topics in the control technology of blast vibration damage. Nowadays, blasting vibration safety standards are based on both the particle velocity and the frequency of vibration and they have been adopted widely and internationally. However, the analysis on vibration frequencies is less studied compared to investigations of peak particle velocity. For the vibration induced by a spherical charge in a viscoelasticly infinite rock mass, an expression of vibration spectrum taking into account the damping effect of rock mass is inferred. Then the attenuation laws of dominant frequencies and centroid frequencies are compared theoretically. For the case of cylindrical charge, dynamic finite element method (DFEM) software of LS-DYNA is employed to analyse the attenuation laws of characteristic frequencies. The research demonstrates that, no matter whether it is a spherical charge or a cylindrical charge, there is a local mutation or fluctuation at some distance when the blast proceeds, while the centroid frequencies conform to a smooth attenuation law. Both the multipeaks structures of vibration spectra and the decay rate difference between high- and low-frequency components contribute to the mutation or fluctuation investigated in this study. Additionally, an increase in longitudinally sonic velocity or the quality factor of rock mass produces an increase in the vibration frequencies, whereas an increase in blast source diameter or the rise time of blast load produces a decrease in vibration frequencies from a spherical charge. In borehole blasting, there is a positive correlation between the vibration frequencies and charge diameter, whereas there is a negative correlation with charge length. And altering the initiation plan will change vibration frequencies to various degrees. Finally, theoretical analysis results were validated by the empirical data from field experiments of Fengning pumped storage power station.CITATION:Zhou, J R, Lu, W B, Chen, M, Yan, P and Wang, G H, 2015. A further study on the attenuation laws of blasting vibration frequency, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 673–682 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S Fidler

Underground coal gasification (UCG) is a process by which coal is converted in situ to a combustible gas that can be used as a fuel or chemical feedstock. The process has been used in commercial-size projects in the former Soviet Union for more than 40 years, while significant national research programs have been undertaken in the United States and Western Europe. The Chinchilla UCG project is located at a site southeast of Chinchilla in Queensland. The UCG operation commenced in December 1999. A controlled shutdown of the process was initiated in January 2002 and successfully completed in April 2003. The process is currently under conservation and ready for restoration of gas production for commercial use in the near future. Groundwater plays an important role in the gas formation process during UCG. Most of the process water required for chemical reactions is usually derived from the coal seam itself and from surrounding aquifers. If insufficient water is available for chemical reactions the UCG gas will contain reduced concentrations of combustible components, and conversely, excessive water influx into the process area would cool down the reactor and thus limit the energy available for gas production reactions. Because of the importance of groundwater in the gasification reactions, and the potential to contaminate groundwater if the process is not correctly controlled, it is essential to predict and to control the groundwater influx into underground gasifiers during and after underground gasification. Control of groundwater requires a thorough understanding of hydrogeological conditions in the vicinity of the gasifier in order to be able to predict inflow rates, and constant monitoring throughout the process of water production rates and groundwater pressure in the coal seam and adjacent aquifers. Hydrogeological testing and groundwater monitoring in the vicinity of the UCG operation commenced six months in advance of its initiation. Monitoring of groundwater pressures in the vicinity of the gasifier have also been undertaken using vibrating wire piezometers installed in the coal seam at varying distances from the gasifier. This paper presents the results of the hydrogeological testing and groundwater quality monitoring carried out at the site, which show that it is possible to operate a UCG process without uncontrolled impacts on groundwater.

Jan 1, 2003

By W. M. LONIE

Address by the President of the Institute (Mr W M Lonie) in making the presentation of the Certificate of Honorary Membership to Sir Ian McLellan, K.C.G.M, K.B.E. Address by Sir Ian McLellan after accepting the award.

Jan 1, 1979

By B Clements, G Lane

The operations and project environments are very different, but overlap in many areas. The development of mineral processing projects is goal oriented, is schedule focused and is a contractual environment. The operating environment for a mineral processing plant is oriented around longer-term commitments, focused on delivery against budget expectations, and an environment heavily influenced by long-term personal relationships, community relationships, and people issues.Further contrast is evident in the way expenditure is managed. Projects commit large amounts of money quickly to meet schedule-based objectives. Operations manage expenditure to minimise operating costs and are able to, or are forced to delay decisions on large expenditures. However, these two environments need to come together in many ways, ranging from greenfields plant handover to a new operations and maintenance crew, to day to day interaction and management of brownfields projects, often in close proximity.This paper considers the different perspectives people bring to projects and early operations, including the advantages and disadvantages of æoperationsÆ input to a project and models for managing value adding during project development, implementation and debottlenecking.CITATION:Lane, G and Clements, B, 2012. Operations versus projects - How do people think and what are the implications?, in Proceedings 11th AusIMM Mill OperatorsÆ Conference , pp 11-16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By G Lane, S La Brooy

A century ago, new mines were often accompanied by smelters. In Australia, smelters were built at the Daydream mine near Broken Hill, at Kuridala and Mount Elliott near Mount Isa, Broken Hill, Mount Lyell, Mount Morgan, Mount Isa, and more recently at Tennant Creek, Kalgoorlie and Olympic Dam. Now the big miners eschew site-based processing in favour of shipping concentrate to smelters in Europe and Asia. As Chip Goodyear was in the process of vacating his leadership role at BHP Billiton, he was quoted as saying that BHP should concentrate on mining ore and leave æto others the skill set of processing that materialÆ. Yet there are times when on-site processing clearly makes sense. Few companies ship gold ore or concentrate to China for gold extraction. New smelters are being built in Zambia. Solvent-extraction and electrowinning plants frequently produce copper from oxide ores and concentrates while pressure leaching is increasingly being considered for copper sulfide ores. Some argue that on-site processing is best because the waste products can be returned to the ground from whence they came, avoiding potentially large disposal costs in more-populated areas. Copper treatment and refining charges will not remain at $45 per tonne and 4.5 cents per pound forever. This paper examines when it makes sense to use on-site pyro- or hydrometallurgical processes in todayÆs environment and comments on how current trends might alter the balance in future.

Jan 1, 2008

By P Rubie, J Russell

This paper looks at the past, present and not too distant future of grinding mill relining.Since the adoption of autogenous grinding (AG) mills and semi-autogenous grinding (SAG) mills as the primary ore reducing devices in the comminution circuit, plant shutdown frequency and duration has largely been driven by the liner maintenance requirements of these mills.The past 30 years have seen the introduction of many technologies to reduce relining times and frequencies. Advanced relining systems have been developed which include single and twin Mill Relining Machines, capable of placing large (up to 8000 kg) liners, high energy recoilless THUNDERBOLT Hammers, and high capacity Feed Chute Transporters. Despite these advances, today many of the hazards associated with mill relining remain and reline times still vary considerably between mine sites. A sophisticated discrete event simulation program, designed to analyse the mill relining process, has revealed the dominant influences on reline times of crew performance and of the need for safe access to larger segments of the mill.A new generation of advanced and semi-automated technologies is currently being tested that will address these remaining challenges. These technologies remove people from the hazardous environment inside the mill and will allow techniques used in modern advanced manufacturing to provide a near-future step change in mill relining safety and performance.CITATION:Rubie, P and Russell, J, 2018. 21st century relining – the path to greater mine site profitability, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 621–640 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By L Jackson, A Parbhakar-Fox, N Fox

"Characterisation of sulfide minerals (eg pyrite, sphalerite) in historic tailings can assist in determining whether there are economic benefits of reprocessing such materials using modern metallurgical practices. In addition, there are associated environmental advantages if the historic tailings are actively generating acid and metalliferous drainage (AMD). At the Old Tailings Dam (OTD), Savage River, Western Tasmania, 38 Mt of pyritic tailings were deposited from 1967 to 1982; consequently it has been recognised as an AMD source. Long-term management options considered for this site have included the establishment of either a water, hard-engineered or vegetation cover. However, due to geotechnical challenges posed and the lack of success demonstrated by previous pilot studies, these strategies have not been implemented. Instead, resolving the pyrite chemistry can allow for a first-pass assessment of whether reprocessing these tailings is a feasible option as part of a long-term management strategy for this legacy site.Tailings samples (n = 144) were collected across the OTD from up to 2 m depth from five facies (A–E), and four zones (1 to 4; defined by hydrological regime and grain size). These materials were subjected to acid-base accounting (ABA) and mineralogical evaluations to determine their geoenvironmental characteristics. Following this, 26 samples were selected for in-depth laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) investigations to evaluate pyrite chemistry across different tailings facies. The results revealed enrichment of Co and Ni in these materials. Specifically, Co content was up to 3.0 wt per cent, particularly within facies C to E, and Zones 3 and 4. Cobalt is recognised as a critical metal, therefore, reprocessing should be considered as a future rehabilitation option for the OTD, pending resource definition using established codes and practices.CITATION:Parbhakar-Fox, A, Fox, N and Jackson, L, 2016. Geometallurgical Evaluations of Mine Waste – an Example from the Old Tailings Dam, Savage River, Tasmania, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 193–204 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By S Morgan, D J. Bradshaw, S Schwarz

The characterisation of the flotation kinetic response in future mining deposits is important because the flotation response is affected by changes in ore mineralogy. Current methods for characterising the flotation response of different ore types, such as the JK floatability index test (JKFIT) methodology, require at least 10 kg of feed material. In geometallurgical applications, this material is taken from core samples. Core samples are generally obtained using specialised drills and are limited in nature. Thus, it would be beneficial to develop a laboratory technique that required less sample material but still characterised the flotation response of different ore types. The JK mineral separation index (JKMSi) is a small-scale flotation test that requires significantly less feed material (10 g of sample/data point). This study aims to investigate the JKMSi system kinetics and to validate this technique using the JKFIT proven methodology. The JKMSi flotation kinetics were manipulated by varying selected system parameters. The relationship between these parameters and mineral recovery was used to obtain floatability characteristics of the ore. For an ore sample containing chalcopyrite and pyrite, it was found that the chalcopyrite floatability parameters determined from both the JKMSi and JKFIT tests were of the same order of magnitude and the mass fractions of the fast, slow and non-floating components were similar. For pyrite, the floatability parameters were not of the same order of magnitude, but modifications to the test procedure have been identified, which may correct this.CITATION:Morgan, S, Bradshaw, D J and Schwarz, S, 2012. Julius Kruttschnitt Mineral Separation Index - Small-scale test to characterise the flotation response of an ore type, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 159-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By N Haque

Base metal ores contain low levels of toxic/hazardous elements such as arsenic, antimony, bismuth, cadmium, lead and mercury. Given the large tonnage of base metal ores mined and processed each year globally, the accumulated mass of minor elements introduced into the biosphere is large and could be expected to have a significant environmental impact. Life cycle analysis (LCA) is a methodology that has been developed to assess the environmental impacts of material supply chains over their entire life cycle. Assessing the toxicity impacts of metallic wastes and incorporating these impacts into LCA methodology is not a simple task given the complexity of the issue. However, research and methodology development is in progress internationally to address this. Despite limitations concerning the lack of a coherent framework for characterising the toxicity impacts of metals, including issues such as bioavailability, a study was carried out to give first estimates of the relative toxicity impacts of various waste streams from metal production processes. The wastes considered were: red mud; sulfide tailings (copper, nickel, lead/zinc); lead/zinc slags; synthetic rutile residue; iron oxide residue; and copper slags and anode slimes. These toxicity estimates can be considered the æworst caseÆ scenario for these wastes, where all the metals present are bioavailable. Combining estimates of the amounts of the various waste streams produced in Australia each year with the toxicity results showed that despite their relatively low human toxicity impact per unit mass compared to some other waste streams, red mud and the various sulphide tailings had the highest annual human toxicity load on the environment, along with copper smelting slag and dust. Data from the pH dependent leaching test reported in the literature were assumed to represent first approximations of metal bioavailability and used to compare the two approaches to estimating the toxicity impacts of red mud.

Jan 1, 2009