Search Documents

By J. W. Marx, R. H. Langenheim

The injection of heat-bearing fluids may offer a wider application to secondary and tertiary recovery from conventional oil reservoirs than inderground combustion since the process is more easily controlled and the reservoir requirements, in general, are less critical. In all cares, conduction heat losses to overburden and un-derburden will impose an economic limit upon the size of the area which can be swept out from any one injection point for any given set of conditions. The present report describes a method for c.rtin~ating thermal invasion rates, cumulative heated area, and theoretical economic limits for sustained hot-fluid injection at a constant rate into an idealized reservoir. Full allow-ance is made for non-productive reservoir heat losses. Required solutions can be obtained directly from the numerical tables given here, as soon as all operating conditions are specified, withou extensive mathematica1 ~nanipulation on the part of the user. The injection of a heat-bearing fluid into a reservoir is frequently proposed as a means of secondary or tertiary oil production. This form of thermal recovery may offer a wider application to conventional oil reservoirs than underground combustion since the process is more easily controlled and the reservoir requirements, in general, are less critical. Because of its large gross heat capacity, steam appears to be the most efficient heat injection medium, although mixtures of steam and other gases, hot water, hot oil and hot non-condensable gases also have been employed. Whatever the nature of the injection medium, economic evaluation of such thermal recovery processes will depend upon thermal invasion rates, or rates of productive reservoir heating, at any given time after the start of heat injection. In all cases, conduction heat losses to overburden and underburden will impose an economic limit upon the size of the area which can be swept out from any one injection point, for a given set of reservoir conditions, at any given heat injection rate. The present report describes a method for estimating thermal invasion rates, cumulative heated area and theoretical economic limits for sustained heat injection at a constant rate into an idealized reservoir, making full allowance for non-productive reservoir heat losses. Required solutions can be obtained directly from the nu- merical tables given here, as soon as all operating conditions are specified, without extensive mathematical manipulation. It should be noted that ordinary water flooding may be used to move an annular-heated zone outward, even though the economic areal limit for straight heat injection has been reached. Thus well spacing need not be confined to the areal limits as determined here. However, the present calculations do not cover such supplementary heat scavenging programs. The operating element consists of a radial flow system, concentric about the point of injection, with the idealized step function temperature profile illustrated by the dashed line in Fig. 1. The solid curve shown in Fig. 1 gives a qualitative picture of the true radial temperature distribution. It will be shown later that the expressions given below, which are derived from the simplifying step idealization (dashed line in Fig. I), also can be interpreted in terms of the more realistic temperature distribution shown in Fig. 2. For this case, the thermal invasion radius is simply redefined as the distance from injection well to the mid-point of the temperature distribution.

By H. L. Sauder, J. L. Newman, C. Waddell

An instrument capable of measuring subsurface flow rates is described. The instrument is self-contained and may be run on piano wire line. It detects flow by means of an impeller suspended between two torsion wires. The force of the well fluid striking the impeller causes the impeller to rotate, exerting a torsional force to the wires. This force is determined by recording the angle of rotation of the impeller on film using a battery-driven, clock-controlled camera. The impeller is sensitive to flow in either direction and the same instrument can be used to measure injection as well as production rates. Changes in direction of flow, such as might be caused by thief zones, are measurable and are indicated by a reversal of the direction of rotation of the impeller. Adjustment of the sensitivity of the instrument to measure a wide range of flow rates is accomplished by the use of different size torsion wires. An umbrella-type fluid trap, which contacts the casing or wellbore, diverts the flow through the flow tube. The fluid trap remains closed while rurrning in the hole and can be opened at any point in the well. The instrument with the trap closed is 1 3/4 in. OD and may be run through 2 in. tubing. Successful flow profiles have been made on wells with flow rates ranging from 60 BID to 4,000 B/D at surface pressure up to 4,500 psi. The instrument is designed for high-pressure and high-temperature operations. INTRODUCTION The need for an instrument that will measure flow rates in a wellbore is as old as reservoir engineering itself. A number of such devices have been designed within the past few years. Some of these have been described in the literature1,2,3,4,5,6 One of these devices1. a hot-wire anemometer type, made many successful jobs in dry gas producing areas. Difficulty was encountered when this flowmeter was used in wells producing liquids and development work was initiated to overcome this difficulty. The present flowmeter is the result of this work and provides an instrument with a wider range of application in the industry. Consider- able development work has been done on the tool involving many changes in the mechanics of recording the flow readings, however, the basic principle of flow detection has remained the same since its inception. PRINCIPLE OF OPERATION The basic principle of operation of the flowmeter is the utilization of a portion of the kinetic energy of flowing well fluid to impart a rotational force to an impeller suspended between two torsion wires. This impeller, Fig. 1, is a screw-type propeller with the blades having a pitch angle of 40. As the well fluid passes through the instrument it strikes the impeller. The resulting force rotates the impeller and twist\ the torsion wires to a balance point at which the torque imparted to the wires balances the force required for the impeller to deflect the well fluid. The impeller is symmetrical and a change in direction of the flow results in a reversal of the direction in which the impeller is deflected. Thus the direction of the flow as well as its velocity is indicated. A dial is attached to the impeller by means of a hollow tube through which the upper torsion wire extends. The angular position of the impeller is recorded by photographing the dial at frequent intervals. In any given set of torsion wires the modulus of shear and polar moment of inertia remain constant and the deflection varies directly with the applied torque. The deflection imparted to the torsion wires also varies as the square of the fluid velocity. Further, the velocities represented by any two given deflections hear the following relationships: and Where V = velocity of flow stream and O ;= deflection. This is the basic relationship which is used to calculate the relative velocities represented by a given set of deflections where the velocity represented by any one of the deflection readings is a known quantity. For a given torque, the deflection of the torsion wire varies inversely as the fourth power of the wire diameter. Wire sizes ranging from ,005 in. in diameter to .022 in. in diameter can be used. The range of

Jan 1, 1957

By R. G. Ward, John Henderson. R. G. Hudson, G. Derge

Densities of melts of the iron oxide-silica system in contact with solid iron have been measured by the maximum hubble pressure method in the composition range O to 37 wt pct SiOz and the temperature range 1255 to 1410C. The constitution of the melts is discussed and it is postulated that the structure changes from a dislribution of iron ions in an oxygen ion network at pure "FeO" to a distribution. of iron ions in a network of silicate tetrahedra at the orthosilicate composition. JOHN HENDERSON, Junior Member AIME, was formerly with the Metals Research Loborotory, Carnegie Institute of Technology, Pittsburgh, Pa., on leave from Broken Hill Proprietary Co., Ltd., Research Division, Shortland, Australia. R. G. HUDSON, formerly with Metals Research Laboratory, is now with the John Jay Hopkins Loborotory for Pure and Applied Science, General Atomic Division, General Dynamics Corp., LaJolla, Calif. R. G. WARD, was formerly with the Department of Metal lurgical Engineering, Carnegie lnstitute of Technology, while on leave from the Department of Metallurgy, University of Sheffield, England. G. DERGE, Member AIME, is Jones and Laughlin Professor of Metallurgical Engineering, Carnegie lnstitute of Technology. Manuscript submitted January 19, 1961. ISD The system iron oxide-silica is an important one metallurgically because it forms the basis of several complex slag systems in use for industrial smelting and refining processes. In recent years considerable work has been done on liquids of this system but there are still many points of difference among workers using different experimental techniques and theoretical approaches. Phase equilibria/"3 activity,4-6 electrical conductivity,' current efficiency,' transference number,8 viscosity,9 surface tension,'' and density" measurements have all contributed to an understanding of the problem. Measurement of density is one procedure which is directly indicative of liquid structure since any deviation from ideality must be a result of structural interactions. Liquids of the iron oxide-silica system are of special interest because this is one of the few metal oxide-silica systems on which measurements can be carried out conveniently over the entire composition range from pure oxide to silica saturation. This includes the range of high basicity which has received relatively little attention in other systems. Although one investigation of density in this system has previously been undertaken," the results seem of sufficient importance to warrant the independent redeter-mination reported here.

Jan 1, 1962

By B. W. Gandrud

WET-PROCESS coal-washing tables as we know them today have been in use in this country for approximately 25 years. The literature records only a few table installations worthy of note prior to adoption of the present-day differential-motion table. According to Phillips,' six Campbell bumping tables were being operated by the St. Bernard Coal Co., Earlington, Ky., in 11893. As late as 1923, according to Richardson, 2 72 such tables were in operation in the Rosedale washery of the Cambria Steel Co., at Johnstown, Pa. Bumping tables probably were not used to any considerable extent except in the plant at Earlington, and at two or three plants in Pennsylvania, but they may be considered as forerunners of the present-day coal-washing table. The transition from bumping tables to the type of tables now in use signalized a revolutionary change in table design. The advantages of the new design over the old were so outstanding as to make its adoption inevitable. BUMPING TABLES Bumping tables, as the name implies, utilized a bumping action for conveying the refuse and discharging it over the refuse end. The tables were hung from rods attached to overhead supporting beams. A shaft and cam arrangement at one end of the table served as the actuating mechanism and imparted to the table an endwise, back-and-forth, swinging motion. A bumping block was fixed in the proper position at the shaft end, so that the table would strike against it at the end of each backward swing. The hanger rods or stirrups were so adjusted as to give the table a slight uphill slope toward the refuse end; that is, the end next to the driving mechanism. The feed box was near the upper end, of the table and designed to spread the mixture of coal and water over the width of the table. Wash water was added a short distance below the feed box with the table in motion and coal mixed with water being fed to it through the feed box, a certain amount of stratification took place, depositing heavy refuse at the bottom of the bed in contact with the surface of the table. Constant bumping and a certain amount of

Jan 1, 1943

By John B. Dilworth

In September, 1930, H. N. Eavenson, then Chairman of the Coal Division, appointed a Committee on Methods of valuing Coal Propelvties, with John B. Dilworth as chairman. The latter prepared a schedule' of features for consideration under the general headings of Undeveloped and Developed Coal Properties. These subjects were divided among the members of the committee and during the next year written discussions of his allotted subjects were received from each member. Mr. Grimes and Mr. Eavenson discussed the entire list,. These discussions were mimeographed and a set sent to each member before the meeting of the Institute in February, 1932. There was a general discussion at that meeting. At the meeting in February, 1934, Mr. Dilworth submitted a report12 which summarized the accumulated opinions and data and presented the conclusions of the committee as a whole on the subjects embraced in it's schedule. Members of the committee expressed the desire that some of the individual opinions be published for reference. Mr. R. Damon Hall's abstracts of these papers arc therefore presentrd herewith.3 Personnel of Committee John B. Dilworth (Chairman), Consulting Mining Engineer, Edward V. D'Invilliers Engineering Co., Philadelphia, Pa. Eli T. Conner, Consulting Mining Engineer, Seranton, Pa. W. G. Duncan, Jr., Superintendent, W. G. Duncan CoaI Co., Greenville, Ky. Howard N. EAveNson, Consulting Mining Engineer; Eavenson, Alford & Hicks. Pittshurgh, Pa. George Watkin Evans, Consulting Mining Engineer, Seattle, Wash. J. A. Garcia, Consulting And Constructing Engineer, Allen & Garcia Co., Chicatgo. III. John Alden Grimes, Valuation Engineer, Bureau of Internal Revenue, Washington, D. C. Otto Herres, Assistant Manager, United States Fue1 Co., Salt Lake City, Utah. J. R. Hicks, Consulting Mining Engineer, Eavensorl, Alford & Hicks, Pittsburgh, Pa. Robert D. Reeder, Mining Engineer, U. S. Bureau of Mines, Washington, D. C. Samuel, A. Taylor, Consulting Engineer, Pittsburgh, Pa. Bleeckee L.. WHeeler, Mining Engineer, Ford, Bacon & Davis, New York, N. Y.

Jan 1, 1934

By Hugh S. Spence

In the winter of 1941-42, muscovite mica was discovered by a young prospector, Justin Purdy, in the township of Mat-tawan, Nipissing District, Ontario, a few miles north of the small settlement of Eau Claire, which lies on the main Transcontinental Highway (No. 17) between Mattawa and North Bay. Muscovite had been known for many years to occur in the general Mattawa region, and various small efforts at production had previously been made by individuals working scattered deposits in the area. These minor activities, however, had never led to production of any consequence or the discovery of any important mica bodies. The Purdy finds were made in a heavily timbered, mountainous area lying about three miles north of the low-lying settled land along the highway, and in a section not hitherto prospected. The mica taken by Purdy and two partners from surface outcrops proved so remarkable in point of size of trimmed sheets that the find attracted considerable attention, and the area surrounding the three claims taken up by the prospectors was quickly blanket-staked by various interests. Though a number of other mica-bearing pegmatite dikes were found later on these stakings, none proved as rich as those on the original Purdy ground; very little commercial mica was obtained from them and attempts to develop them were short-lived. Purdy and his partners sold their initial production to dealers in Ottawa and Hull, where the Canadian mica industry long has centered. Young Purdy, unfortunately was killed in a motor accident in the early summer of 1942. His father continued mining operations for a few months and produced and sold a considerable amount of mica. In October 1942 the Purdy holdings were acquired by lnspiration Mining and Development Co. of Amos, Quebec, which had been active in staking in the area. This company formed a subsidiary, Purdy Mica Mines, Limited, to develop the property. Under the energetic management of Joseph R. Norrie, rapid progress was made, and production soon attained important proportions. Realizing from the outset the unusual character and potential value in the war effort of the Purdy discovery, the Metals Controller, Department of Munitions and Supply, at once arranged with the Department of Mines and Resources for an official geological report on the area, and also drew the attention of the War Production Board in Washington to what seemed likely to prove a highly important source of strategic-quality mica. Officials of WPB were sent up in the Summer of 1942 to inspect the property, and so impressed were they with the possibility that it might become of high

Jan 1, 1948

By C. Dean Starr

The physical basis of the equation correlating electrical conductizlity and temperature coefficient of resistance of solid solution alloys has been inzlestzgated and the nature of the constants evaluated. It is shaun that the same form of correlation is valid irrespective of the magnitude of the temperature coefficient. However, the effect of therma1 expansion and change in resistivity with temberature nust be considered when the magnitude of the temperature coefficient of resistance is near zero. In a comprehensive literature survey conducted at the Armour Research Foundation in 1950, it was found that a linear relationship exists between the electrical conductivity, K, and the temperature coefficient of resistance, a, for solid solution alloys. This was expressed by the equation where B, a constant, depends on the solvent metal but not the solute. A continuing investigation by Hansen, Johnston, and Parks showed this equation was generally appropriate for Cu, Ag, Au, Pd, Pt, and Co base binary solid solution alloys as well as for many ternary alloys of copper over a range of conductivities and temperature coefficient of resistances from 0.02 to 0.60 reciprocal pohm cm and-0.00015to0.004Q per 0 per "C respectively. Eq. [I] was not always valid for alloys that exhibited a change in state (magnetic to nonmagnetic) or for alloys that had a temperature coefficient of resistance near or below zero. For example, in nickel alloys, a simple linear curve as predicted by Eq. [l] was not obtained when the conductivity was plotted against the temperature coefficient of resistance. Hansen suggested that deviations observed were caused by transitions from a ferromagnetic to a nonmagnetic state. Subsequent and more extensive data by ronin on Ni-Mn alloys confirmed Hansen's postulate. While both states independently showed a linear relationship between K and a, the value of B was different for the two states. In some copper and gold base alloys, as well as the platinum and palladium alloys investigated by Hansen, the conductivity did not extrapolate to zero at zero a as demanded by Eq. [I]. This deviation can be readily corrected by simply adding a constant to Eq. [I.] whence Eq. [2] shows the K decreases as a decreases but that K has a positive value when a = 0 which is observed for commercial solid solution alloys as well as the experimental alloys tested by Hansen. While other methods of correlation of electrical properties have been made such as the one by Starr and Wang3 who found a linear relationship between resistivity and temperature coefficient of resistance for Ni-Cr-Al-Cu alloys, the data, in general, can also be correlated by a form of Eq. [2]. Thus, Hansen's empirical equation has considerable merit. The objective of this paper is to determine the physical basis for this equation and to examine the region near zero a in more detail. ELECTRICAL CONDUCTIVITY VS TEMPERATURE COEFFICIENT OF FU3SISTANCE The resistance of a metal or alloy is defined as

Jan 1, 1963

By J. A. Scott, F. R. Hensel

The paper deals with the investigation of two types of coreless induction furnaces, one of 60 cycles, the other of 5000 cycles. Nickel was used as test material and the absorption of oxygen by molten nickel was chosen for determining the influence of the frequency on the metallurgical characteristics of the furnaces. Dr. Herty's aluminum method, slightly modified, was found suitable for determining the nickel oxide content in nickel. Also an electrolytic method for determining alumina in nickel was worked out. The solubility-temperature relations for nickel oxide in molten nickel were determined approximately. It was found that the solubility of nickel oxide increases with the temperature. Comparative tests on the rate of oxygen absorption made in a 60 and a 5000-cycle furnace showed that the absorption of nickel oxide in nickel is an increasing function of turbulence, time and temperature. The rate of oxygen pickup in the 60-cycle furnace is about three times as great as in the 5000-cycle furnace. In the 60-cycle furnace the maximum oxygen content of the melt comes close to the saturation limit. Melting under an oxygen-free atmosphere prevents oxidation in both types of furnaces. DISCUSSION (Iloward Scott presiding) H. Scott, East Pittsburgh, Pa.—When Professor Desch was in Pittsburgh recently he mentioned that the induction furnace has practically replaced the crucible furnace in Sheffield except for the carbon tool steels. Dr. Hensel is to be congratulated on the development of analytical methods for determining inclusions and for getting two different methods to agree. F. R. Hesnsel—Recently the purification of molten metals with hydrogen or other suitable gases has become an important issue and a number of patents have been taken out covering gaseous treatments of molten metals. In this connection I wish to call

Jan 1, 1933

By C. S. Finney, John Mitchell

The growing popularity in the United States of the vertical-flue even was emphasized when in 1905 the United States Steel Corp. chose the Koppers oven as the type which best suited their requirements. Heinrich Koppers was born on November 23. 1872. at a small farm in Walbeck near Geldern on the lower Rhine. When young Koppers was eight years old, however the family moved away from the farm to the industrial city of Bochum in the Ruhr. Here Koppers attended public school and subsequently served an apprenticeship to a tinsmith before taking a job as a lathe operator with a local steel company. He had ambitions to be much more than a machinist, however, and used his week-ends and evenings to improve his theoretical background by taking courses at a vocational-training school in Bochum. After winning the highest honor the school could bestow (the silver Staats-medaille), Koppers went on to continue his education at the Rheinisch-Westfalische Hüttenschule in Duisberg. One of his teachers there, Fritz Wüst who later became a professor at the Technische Hochschule at Aachen, recognizing Koppers' unusual abilities, predicted for him a great future. In 1894 Heinrich Koppers joined the firm of Dr. C. Otto and Co. in Dahlhausen, and in 1899 while superintendent of the Mathias Stinnes mine he built his first battery of ovens for Hugo Stinnes, the German industrialist. Two years later he started his own organization, and in 1902 he made Essen his headquarters. It was to Essen that a group of engineers from the United States Steel Corp. went in 1906 with an invitation to Koppers to design and supervise the construction of four batteries of ovens at the Joliet works of the Illinois Steel Co. Each battery was to consist of 70 ovens. Arriving in the United States in 1907, Koppers established a branch of his firm in Joliet, and construction began. The first battery was fired on July 27, 1908. Rugged and simple, these ovens incorporated basic design features which were to make the Koppers oven and its future modifications the choice of a very large segment of the by-product coking industry of America. The 280 ovens at Joliet were 35 ft long, 8 ¾ ft in height, and tapered from 21 to 17 in. The total daily capacity of the four batteries was 2240 tons of coke. The ovens were of the new cross-regenerative type; that is, instead of longitudinal regenerators serving an entire battery, as in the older Koppers ovens, cross regenerators for each separate oven were employed. Fuel gas was supplied from the side of the battery through ducts in the brickwork known as gun flues, which reached to the center of the battery under the vertical heating-flues. Removable, ceramic gas-nozzles fitted at the top of each gun flue helped to insure good control over the distribution of the fuel gas, and uniform heating conditions were also promoted by regulating the air supply to, and the suction in, each heating flue. A different refractory w& used for each battery. One was built of American silica brick, one of American quartzite, and two of imported German quartzite. The installation at Joliet proved to be very successful, and in 1911, 490 additional' Koppers ovens were built for the Illinois Steel Co. at the great new steelworks at Gary, Ind. By 1912 the H. Koppers Co. had established its headquarters in Chicago and was rapidly extending its business to include construction for such iron and steel companies as the Woodward Iron Co. at Woodward, Ma. (80 ovens in 1912); the Tennessee Coal, Iron and Rail- road Co. at Fairfield, Ala. (280 ovens in 1912); the Inland Steel Co. at Indiana Harbor, Ind. (86 ovens during 1913 and 1914) ; and the Republic Iron and Steel Co. at Youngstown, Ohio (68 ovens in 1913). In 1914 a group of men in Pittsburgh bought a major shareholding in the H. Koppers Co., and moved the headquarters of the organization from Chicago to their own city. Under its new management the company was highly successful in obtaining a large share of the contracts for by-product installations built during World War I. In 1917 the remaining German interests in the company were

Jan 1, 1961

By Philip Davidson, Wm. B. Price

The object of this paper is to present, a survey of some of the physical properties of sheet nickel silver when subjected to cold rolling and when annealed at temperatures extending from 350" C. throughout the coininercial annealing range.. A number of alloys were taken from stock and analyzed. Four of these, representing low nickel and high nickel both with and without lead, were chosen for the tests. The analyses were as follows: Alloy Copper, Lead. Iron. Nickel, ManGanese, Zinc, PeR Cent. Per Cent. Per Cent. Per Cent. Per Cent. PEr Cent. A................ 64.68 Trace 0.194 6.73 0.06 remainder B................ 65.82 1.27 0.227 6.17 0.06 remainder C................ 65.44 Trace 0.345 17.83 0.08 remainder D................ 65.60 1.08 0.238 17.77 0.06 remainder These alloys were lolled in accordance with regular mill practice to approximately No. 6 R. & 6. gage. The bars (which were then coiled) were annealed together in a mill muffle and afterwards pickled in a 10 per cent. sulfuric-acid solution and cold rolled in stages of approximately one number (B. & S.) at a time to No. 18 B. & S. gage. After each stage, suitable samples were set aside for physical tests. Additional samples were chosen for tests after the bars were rolled to Nos. 8, 10, 12, and 14 gage. These samples were annealed together in the mill muffle and, after pickling, were finished on 0.050-in. gage, yielding a series of specimens 2, 4, 6, and 8 numbers hard for the subsequent annealing tests. Tensile test pieces 9 by 1 in. (22.9 by 2.5 cm.) were cut from both lots and the central portion was milled to give a test section 2 1/2 in. long by 1/2 in. wide. A distance of 2 in. was marked off on the edge of each specimen with light punch marks. In the case of the annealed alloys, Erichsen test pieces 4 by 235 in. were also taken.

Jan 1, 1921

By Michael Hoch, Seong Kwan Rhee

The ternary system Zr-Cr-0 was investigated at 1200°, 1500°, and 1700°C. The isotherms at these temperatures were determined by metallographic and X-ray diffraction analysis of carefully selected alloys. AS a part of a series of investigations1-4 of the ternary and quaternary phase diagrams on refractory metals and their compounds, the ternary system Zr-Cr-O was investigated at 1200°, 1500°, and 1'700°C. The binary diagrams Zr-Cr, Zr-O, and Cr-0 as reported by Hansen5 and Levin et a1.' and the existence of a ternary coompound ZrsCrsO (q-carbide structure a. = 11.96A) provided a good base for this investigation of the Zr-Cr-O phase diagram. MATERIALS The materials used and their suppliers were: Zirconium powder, 99.4 pct pure, Charles Hardy, New York; Zirconium dioxide, Fairmount Chemical Co., Newark, N.J.; Chromium powder, 99.85 pct pure, Fairmount Chemical Co., Newark, N.J.; Chromium sesquioxide, 99.86 pct pure, J. T. Baker Chemical Co., Pillipsburg, N.J. Though the materials used were not "hyperpure", the impurities present do not affect the results (lattice parameters, phase boundaries) within the experimental accuracy. EQUIPMENT AND PROCEDURE The detailed procedures and equipment used for this investigation were similar to those described elsewherel' "ith the exception that in this study an induction-heated argon-atmosphere furnace was used. The latter furnace was used to prevent the vaporization of chromium metal in samples in the higher temperature range (above 1200°C). The tungsten crucible was induct ion-heated in a vertical quartz tube filled with argon gas. The quartz tube was 1-1/2 in. in diameter and 10 in. long; it was connected at the top and bottom to water-cooled copper plates. The argon gas of a purity 99.995 pct was further purified by being passed through zirconium metal chips which were maintained at 800°C in a silica tube 1 in. in diameter and 30 in. in length. The furnace was flushed with argon gas for an hour before starting heating; during heating, a slight (3 cm oil) overpressure of argon was maintained in the system. Power was supplied by a 20-kw Ther-Monic Induction Generator. The samples rested on a tungsten-wire basket; the wire basket was connected to a tungsten wire which passed through the tungsten crucible lid, and entered the system on top through a Wilson-type seal. By pulling on the wire, the sample was removed from the crucible and dropped to the water-cooled copper base of the furnace. Because of the presence of argon gas, the cooling of the sample was even more rapid than in the vacuum furnace.' EXPERIMENTAL RESULTS AND DISCUSSION 1) Isothermal Section at 1200°C. The compositions investigated have been numbered within the phase diagram, Fig. 1, and all the pertinent information about the samples can be found in Table I. This table lists the composition of the samples, the phases present in the room-temperature diffraction patterns, the phases detectable in the microstruc-ture, and calculated lattice parameters of the a-zirconium phase. The shapes of the various phase

Jan 1, 1964

By Robert Gorham Morse

This paper presents the results of an investigation made in the metallurgical laboratory of Columbia University, New York City. The object of the investigation was to determine how the tensile strength, the elastic limit, and the size of the grain, of a pure medium-carbon steel are affected by heating to successive temperatures between 500° and 1300° C., with slow cooling therefrom. Since Dr. Sorby's first investigations into the microstructure of steel, the study of the subject has been continued by Professor Martens, Mr. F. Osmond, Professor Arnold, Professor Howe, Mr. A. Sauveur, Mr. J. E. Stead, and many others. Among many valuable and interesting papers I mention the following as having a special bearing upon this investigation.* " Microstructure of Steel," by Albert Sauveur, Trans., xxii., 546 (1893); Microscopic Metallography," by F. Osmond, Trans., xxii., 243 (1893); "The Microstructure of Steel and the Current Theories of Hardening," by Albert Sauveur, Trans., xxvi., 863 (1896); "The Crystalline Structure of Iron and Steel," by John Edward Stead, J. Iron and Steel Inst., 1898. II.—Statement of Experiments. Through the kindness of Mr. N. Lilienberg, New York City, round rods 3/4 of an inch in diameter were obtained, which had been rolled from one ingot. The analysis of the steel was as follows : C, 0.343; Si, 0.027; Mn, 0.221; I?, 0.0266; S, 0.0037 per cent.

Jan 1, 1900

By F. E. Smith, David R. Mitchell, B. M. Bird

DENSE-MEDIA processes utilize the familiar laboratory float-and- sink procedure on a commercial scale. Just as wood chips float on water and sand sinks, ,so coal floats and refuse sinks when placed in a medium intermediate in specific gravity between the coal and refuse. Liquids intermediate in specific gravity between coal and refuse used in commercial plants are of four types: (1) Organic liquids of high specific gravity-halogenated hydrocarbons; (2) dissolved, salts in water; (3) pseudo liquids obtained by suspending solids, such as sand, in water, and (4) fluidizing a mass of sand or other solids by air currents. Those most widely used for cleaning coal are solutions of calcium chloride in water and a suspended-sand pseudo liquid. Laboratory float-and-sink testing is an intermittent operation during which every opportunity is given for particles lighter than the medium to float and particles heavier to sink. Commercial processes are continuous, vertical and horizontal currents of the separating medium occur as either part of the process or unavoidably produced by the introduction of feed and withdrawal of products, so that the exact separation of the laboratory technique is not duplicated by commercial processes. However, separations close to the theoretical are obtained in commercial machines by careful technical control of the process. Most machines in commercial installations are crowded to get as much out of the equipment as possible, so that careful technical control is necessary to get the recoveries and grade of product desired. Sizes usually cleaned are plus 3/16-in. or plus 1/8-in. in the United States and plus 1/16-in. in Great Britain: Coal as small as 1 mm. has been cleaned in some experimental installations. The separation of coal from refuse in sizes finer than about in. is made difficult by viscosity' effects and hence at the present time cleaning is confined to the coarser sizes. Technical advances in the art of cleaning coal by dense-media

Jan 1, 1943

By J. O. Brittain, N. R. Adsit

A number of zinc bicrystal specimens with the grain boundary loaded in simple shear were plustically deformed in creep in a vacuum at 200°C and under an argon atmosphere at 350°C. The results indicated that the amount of grain boundary sliding at a given time was controlled by the slip in the grains and was proportional to the resolved shear stress on the slip plane. Curves of grain boundary sliding vs time were found to be cyclic with no regular periodicity. ALTHOUGH grain boundary sliding (G.B.S.) has been investigated in a number of different types of tests on various materials there is substantial disagreement on the interpretation of the various observations. Gifkins1 has presented a comprehensive review of the subject of G.B.S. and fracture. He reports that the activation energy for high-temperature creep is equal to that for volume self-diffusion and that pure metals show less tendency towards intercrystalline fracture than alloys. Pure metals show appreciably greater grain boundary migration than alloys, and both grain boundary migration and grain boundary sliding follow the same general trend in time as plastic deformation during creep.' While there have been a number of different mechanisms proposed to account for G.B.S., none of the models explains all the results. Since zinc has only one prominent slip system, it was hoped that experiments on G.B.S. in zinc bicrystals might enable us to separate the effect of grain boundary angle and the effect of matrix slip and thereby resolve at least one part of this complex phenomenon. EXPERIMENTAL PROCEDURE Bicrystals of pure zinc (99.99 pct) were grown by a Bridgeman technique in a furnace having a gradient of 20°C per in. The bicrystals were seeded to a desired orientation and grown in a split graphite mold which was 3/4 by 5/8 by 8 in. The mold was enclosed in a Pyrex tube and the tube was evacuated and then filled with a small amount of argon before it was placed in the furnace. The growth rates were 1/2 to I in. per hr for the bicrystals and 1/2 to 3 in. per hr for the single-crystal seeds. The longitudinal V notches served to hold the grain boundary in position during the growth process. A schematic rep- resentation of a specimen which had been cut with a jewelers saw from the bicrystals is shown in Fig. 1. All specimens of a series were cut from the same crystal, some of which were 7 in. in length. After specimen preparation the boundary was approximately 5/16 in. long and the V notches had a radius of 1/16 in. The boundaries were straight at a magnification of X100 with the exception of a few which had a gradual radius of curvature of greater than 3.2 in.-1. Laue back-reflection photograms were taken on the specimens to check the orientation of grains in the bicrystals. The method of relating the orientation of the two lattices is shown in Fig. 1, where 0 is the angle between normal to the boundary and the trace of the basal plane, is the angle in the boundary between the trace of the basal plane and a line parallel to the V notch, and x is the angle in the basal plane between the Burgers vector and the perpendicular to the grain boundary. After mechanical polishing the specimens were chemically polished.2 Subsequent to the polishing operation the specimens were encapsuled under a vacuum of better than 25 annealed at 340°C for 1 hr to remove the effects of this handling, and again chemically polished. Finally, fiduciary marks were scribed on the specimen using a micromanipulator. Creep tests, which were conducted in a modified Bausch apparatusS with the boundary loaded in simple shear, were run at a constant load (since the boundary area remained essentially constant this is approximately constant grain boundary stress). The temperature was controlled to ±1/4°C as measured on a semiprecision potentiometer with a calibrated thermocouple. The specimens were tested in a vacuum of better than 0.5 at 200°C and in purified argon at a pressure of 1/2 atm at 350°C. The op-

Jan 1, 1965

By Don M. Jackson, Robert W. Howard

Techniques for the epilaxial growth of single -crystal silicon carbide films on silicon were developed. The vapor-phase decomposition and bydrogen reduction of silicon tetrachloride (SiC14) and Propane (C3H8) resulted in clear films of silicon carbide, lip to seveval microns in thickness. The growth took place in a horizontal . silicon epilaxial reactor at 1100°C (pyrometer) at a rate of- 3000Å per minute. Electron diffraction and X-ray diffraction studies demonstrated that the films were single-cyrstal, ß -phase, or cubic silicon carbide. SiO2 film were used to mask areas of the silicon sur-lace in order that the silicon carbide might be grown in controlled geometries. Both n- and p-type films were grown on p-type silicon waters.. Heavily doped silicon films of the same conductivity type as the silicon carbide films were deposited over the silicon carbide in order to affect better probe contact to the structures. when n-type silicon carbide mesas were grown on p-type silicon substrates the de vollage-current relationships between films and substrates were that of junction diodes. These diodes showed a sensitivity to while light ill that the incident light increased forward- and reverse-satro,ation currents, P-type silicon carbide mesas grown on p-type silicon were ohmic rather than rectifying in their voltage -current relationship. No conclusions could he reached concerning heterojunc-tiou rectification in the structure. SILICON carbide is a semiconductor with many interesting properties. It decomposes at temperatures above 2200°C.1 It occurs in two general crys-tallographic forms—hexagonal (a Sic) and cubic (ß Sic)—with the cubic form having a forbidden-gap energy of 2.32 ev and the hexagonal form (specifically the 6H polytype) a gap energy of 2.86 ev.3 It behaves as an extrinsic semiconductor at temperatures approaching 5003C. It has been shown to have a high resistance to radiation damage4 and p-n junctions formed in Sic have been shown to radiate visible light under forward- or reverse-bias conditions. Epitaxial silicon carbide on silicon carbide has been successfully grown through the use of a variety of techniques, such as gaseous cracking of SiCL4 and CC4, nearly all of which require a deposition temperature above 1500°C.6 This paper will cover very recent work on the gas-phase deposition of highly ordered films of silicon carbide on high-quality silicon single-crystal substrates. The films have been shown to ex- hibit junction-rectification properties when geometrically isolated regions are electrically biased with reference to the silicon substrate. There will be no discussion of the mechanism of heterojunction rectification, but the methods of film fabrication, geometry control, and structural evaluations will be covered in detail. Electron diffraction, X-ray diffraction, and diode electrical properties were used to characterize the films and the junctions. GAS-PHASE DEPOSITION OF Sic The techniques for the deposition of silicon carbide films were a logical outgrowth of the standard silicon epitaxial process. The major premise followed was that, for any film to nucleate in an ordered fashion where there is considerable mismatch in lattice parameters (in this case 22 pct), an extremely clean, damage-free substrate surface must be presented to the gas stream. Thus a standard gas-phase HCl etching step was used to prepare the substrates for growth. A minimum of 5 µ of substrate-surface material was removed prior to the deposition of Sic overgrowth films. The techniques used for growing silicon carbide films were those of growing silicon alone, with the added injection of a hydrocarbon gas into the hydrogen and silicon tetrachloride gas stream. The hydrocarbon gases used thus far have been research-grade (99.99 pct) methane (CH4) and propane (C3H8). Propane ultimately gave the best results. The gas flows were controlled through a panel shown schematically in Fig. 1. A hydrogen main stream of 30 liters per min passed through the horizontal quartz-tube epitaxial reactor, while SiC14, C3H8, HC1, and doping gases were injected as side streams. The

Jan 1, 1965

By K. D. McBean, W. H. Hannay, B. A. Stimmel

The electrolytic plant at Trail, B. C., was erected by the Consolidated Mining and Smelting Company of Canada, Ltd., for the treatment of zinc ores and concentrates, particularly those of the Sullivan mine at Kimberley, B. C. It began operations in 1916 at a rated capacity of 60 tons of cathodes per day, which has been steadily increased to the present production of 400 tons per day. The Sullivan has furnished the greater part of the zinc so far produced, although notable tonnages of customs zinc concentrates have been treated. The maximum yearly tonnage of customs concentrates, 25,000 tons, was treated in 1926. Practically no customs concentrates hale been treated since 1929. The total bar zinc production to the close of 1935 was 1,092,782 tons. The zinc mineral in the Sullivan ore is marmatite of somewhat variable composition, ranging between 6ZnS.FeS and 8 ZnS.FeS. Practically all the zinc ores tributary to this plant are marmatites; and the iron content of the zinc mineral varies considerably. The formation of zinc ferrite during roasting is now a matter of common knowledge, so the possible extraction from any zinc concentrate is largely a function of the iron content; the progress made in concentration is reflected directly in zinc-plant recovery. The Trail plant operafes on the low-acid system, as do all the other major plants on this continent at present operating, except the electrolytic plant of the Sullivan Mining Co. at Kellogg, Idaho. The new Magdeburg plant, in Germany, occupies an intermediate position between high and low acid. Plant operation at Trail will be treated in this paper under five main sections: roasting, leaching and purification, electrolysis, cadmium recovery and melting. The oxide section of the plant, treating zinc fume from re-treatment of lead blast-furnace slag, is practically a separate zinc plant; this is necessary because of the presence of fluorine in the smelter zinc fume. Cadmium is recovered electrolytically from the purification residues of both the sulphide and oxide leaching plants.

Jan 1, 1937

By A. T. English

X-ray dif action techniques were used to investigate ordering and domain coalescence for the B2 (CsC1) superlattice in this alloy. Essentially complete disorder is obtainable by drastic quenching. isothertmal ordering occurs very rapidly at temperatures between 565° and 680°C, only a few seconds being required for development of substantial long-range order. A very fine antiphase dormain structure, found in samples annealed for short times, undergoes coalescence with further annealing. Domain "size" is found proportional to (t)1/2 . This Yate law can be derived by adapting the formalism of Hillert's analysis 01- metallurgical grain growth. For this Purpose the material is descvibed in terms of a "Swiss-cheese " structure, consisting of two multiply connected, mutually intertwined domain volumes. The observed activation enevgy for coalescence, 70 kcal per g-atom, agrees with an estit~lated value ,for volume diffusion in disordered rrzaterial. It is suggesled that the experimental value vejlects the substantially disordered environment of mobile vacancies located in the moving antiphase domain boundary. The alloy Fe-Co-2V is bcc below about 900'C and orders into a B2 (CsC1) superlattice below about 730c It has important applications in magnetic components, including many requiring extensive cold rolling.* example, Marcinkowski and Brown6 observed a re1atively small as-quenched domain size of about 250Å in B2 Fe3A1. Since there appear to be no published data on domain coalescence in B2 alloys, this process was studied in detail. MATERIALS AND EXPERIMENTAL TECHNIQUES A commercial high-purity alloy, nominally 49 Fe-49Co-2V, was obtained from the Arnold Engineering Co. in the form of cold-rolled sheet 0.004 in. thick. Samples were annealed for 1 hr at 800°C in dry H2 to produce disorder and quenched into iced brine. They were then annealed in a nitrate-nitrite salt bath for various times at temperatures between 525° and 625°C. Estimates of the LRO parameter S and the APD size D were made using established X-ray diffraction techniques. Superlattice peaks are best observed using CoKa radiation, for which the value of (fFe-fCo) is maximized. Peak-to-background intensity ratio was improved by filtering CoKß from the incident beam to eliminate sample fluorescence, and by using a pulse-height analyzer. The LRO parameter S was computed from the ratio of integrated intensities I 100/I 200- Owing presumably to systematic errors associated with the presence of crystallographic texture and X-ray extinction, only rough agreement was obtained between experimental and theoretical (absolute) intensity ratios. For this reason certain experimental refinements (e.g., use of balanced filters) were considered superfluous and were omitted. Emphasis was placed on maximizing intensity in order to reduce the time taken to accurately determine the contour of the very small (loo), peak. This was done by point counting 105 counts at appropriate intervals. Background intensity averaged about 1200 cps.

Jan 1, 1967

By G. Wakefield, A. H. Daane, D. H. Dennison, F. H. Spedding

Preparation of pure scandium metal was accomplished by calcium reduction of the fluoride by two methods; a low-temperatzdre alloy process and direct reduction with subsequent distillation of the product. The following properties were determined: melting point: 1181OK; boiling point (calculated): 3000°K; lattice constants at 298°K (hexagonal lattice): a = 3.308 * 0.001 A, c = 5.267 * 0.003A; calculated density at 298°K, g per cm3: 2,990 + 0.007; electrical resistivity, ohm-cm: 299°K, 66.6 ± 0.2 x 10 -6; 373oK, 77.4 * 0.2 x 10 -6; thermal coefficient at 299°K, ohm-cm per deg: 5.4 X x; heat of sublimation at 298°K, kcal pel- mole: 80.79. The vapor pressure was determined as a function of temperature between 1505o and 1748°K, with the data fitted to a straight line shielding the equation: Log Pmm = -1.718 X 104/ToK + 8.298. SCANDIUM, element number 21, was first discovered by Nilson in 1879 and was recognized as the Ekaboron as predicted by Mendeleff. As it is in group III of the periodic table, the general properties are a little like aluminum and also resemble quite closely the properties of yttrium and the rare-earth metals, in both the metallic and ionic form. Although the earth's crust contains approximately 5 ppm of scandium (the element is as abundant as arsenic and twice as abundant as boron) it generally occurs so widely distributed that it has earned the reputation of being very rare. The one exception to this is the mineral thortveitite, which has been found in Madagascar (20 pct Sc2O3) and in Norway (35 pct Sc2O3). Scandium also occurs in small but distinct amounts in uranium and rare-earth ores; the recent larger scale processing of these materials has made some scandium available from these sources. As with other naturally-occurring monoisotopic elements (except Be), scandium contains an odd number of protons and an even number of neutrons. Scandium metal was first prepared by Fischer and coworkers1 in 1937 by electrolysis of scandium chloride in a molten eutectic mixture of lithium and potassium chlorides, using molten zinc as a cathode and collector of the scandium metal produced. The zinc was removed from the Zn-2 pct Sc alloy by vacuum distillation, leaving a product reported to be 94 to 98 pct Sc, with the main impurities being iron and silicon. They reported a melting point of 1400° C for this material. Scandium has also been prepared by the reduction of scandium chloride with potassium metal in a glass apparatus by Bommer and Hohmann in 1941,' resulting in a mixture of metal and potassium chloride; these workers did not isolate the metal proper, but the X-ray diffraction of the slag-metal mixture showed it to be hexagonal with a = 3.30A, c = 5.45A. petru3, 4 and coworkers have recently reported the preparation of the metal in a compact form by the reduction of either ScF3 or ScC13 with calcium metal and subsequent distillation of the product. This process probably yielded a metal of high purity, but they list no chemical analysis nor do they list any of the properties of their product. Previous related work in this Laboratory has been concerned with the production of yttrium and the rare-earth metals and the determination of their physical properties. Because of its similarity to these metals, scandium is being included in this study. PREPARATION OF SCANDIUM METAL The preparation of yttrium and the rare-earth metals may be accomplished by reduction of their fluorides with calcium metal in tantalum crucibles.5 This process leads to the introduction of tantalum (up to 0.5 pct) as an impurity in the higher melting rare earths, but since the tantalum occurs as dendrites, uncombined with the rare-earth metals, its presence is not objectionable in some cases. The preparation of scandium metal in this manner, however, was found to yield a product containing 2 to 5 pct Ta. To obtain a purer product, the following two methods were developed for the reduction of scandium fluoride with calcium metal: i) a low-temperature process utilizing zinc to form a low

Jan 1, 1961

By G. H. Kessler

ALTHOUGH considerable attention has been devoted to reaction mechanisms and equilibria of a number of endothermic reactions through which metals or their refractory compounds can be formed upon heated surfaces, only a comparatively small amount of work has been done to develop rate information for these systems. The interestin and very worthwhile work of Holden and Kopelman, Runnalls and Pidgeon,Dijring and Moliere, and Herrick and ICrieble4 is to be noted; however, their work was done under very specific conditions and the rate information which they have developed is not applicable to many systems which have been studied experimentally. That a more generalized approach is needed is shown by the diversity of these systems and of the experimental conditions which they require. These include the preparation of titanium, zirconium, tungsten, molybdenum, chromium, co-lumbium, aluminum, and silicon by decomposition or disproportionation of their halides, in some instances through hydrogen reduction; the preparation of nickel and iron by decomposition of their car-bonyls; and the preparation of copper by decomposition of the acetylacetonate. They may be carried out at temperatures ranging from 100" to over 2000°C and at pressures of from less than one mm Hg to superatmospheric. The physical mechanism of the overall process can be broken down into several steps, any one of which may be rate-determining; and the rate associated with each of these basic physical processes can be predicted. Consequently, by proper application of the present technology of rate processes, it is possible to arrive at a rate of metal deposition in the system of interest and to reach an understanding of the influence of' each major variable upon the deposition rate. It is the purpose of this paper to illustrate how this can be done and to present experimental results for a specific system for comparison with theory. The overall process of deposition of metal upon a heated surface which is immersed in vapors of a compound of the metal can be broken down into the following steps: 1) Transport of the reactant vapors to the surface. 2) Decomposition of the reactant in the immediate vicinity of the surface to a) establish chemical equilibrium if reaction rates are high; or to b) establish a dynamic equilibrium in accordance with the several reaction rates. 3) Diffusion of reaction products away from the vicinity of the surface, with or without simultaneous recombinations to form still other products. The overall process is said to be diffusion controlled if Step 1, or the equivalent Step 3, is slow; it is reaction-rate controlled if Step 2b is slow. When experimental evidence shows the reaction rate to be controlling, the well-known theories of Eyring' and others can be used as a basis for correlating and extrapolating the experimental data. Although these theories give only approximate estimates of reaction rates, they are of considerably greater value in correlating experimental data. Most deposition systems operate at surface temperatures sufficiently high that reaction rates near the surface are very high. Mass-transport rates then become controlling; and it is this regime of diffusion controlled rates which is most often of concern and Which will be considered here. When the system pressure is very low, i.e., in the micron range, then the transport processes are those of molecular movement, and the results of kinetic theory can be applied to specify a rate of arrival of reactant molecules at the heated surface. If the condensation coefficient can be estimated, then the deposition rate will be given by the product (rate of arrival) x (condensation coefficient), Conversely, experimental data can be used to determine a condensation coefficient, as was done by Holden and Kopelman' for the decomposition of zirconium tetraiodide upon a heated molybdenum surface, who found the coefficient for zirconium on molybdenum to be 1.0 at temperatures of 1382°C and above. In this pressure range, the geometry of the system. and in particular the distance between the source of reactant molecules and the heated surface, can exert a considerable effect upon the deposition rate;

Jan 1, 1961

By C. G. Dunn, J. L. Walter

SILICON-iron .under certain conditions of processing and annealing will form a cube texture. The occurrence of this texture in thin tapes of silicon iron was first reported by Assmus, Detert, and Ibe.' They concluded that the cube texture in their material formed by a secondary re crystallization process. In the course of present investigations on the development of the cube texture and the mechanisms involved in its formation by secondary re-crystallization it was found that under certain conditions the cube texture was replaced by a cube-on-edge or (110) [001] texture. We call this phenomenon tertiary re crystallization since it follows secondary recrystallization. The secondary recrystallization occurs after primary recrystallization and a substantial amount of normal grain growth. It is the purpose of this paper to describe briefly the occurrence of tertiary recrystallization and the structure and texture prior to and after tertiary recrystallization. The primary and secondary recrystallization structures and textures are the subject of another study and will be referred to briefly in the discussion of results. Evidence will be presented for the view that the dominant driving force for tertiary recrystallization is derived from the surface free energy which depends on the crystallographic planes presented to the gas-metal interface. In the absence of boundary restraining forces (dispersed phases, thermal grooves, and so forth) a sufficiently large difference in surface free energy across a grain boundary would produce boundary migration away from the center of curvature of the boundary intersection line in the surface of the sample according to risher.2 Therefore, particular attention was paid to observation of the direction of motion of these surface boundary lines. Furthermore, measurements of the actual boundary curvatures could be used to estimate the driving force supplied by surface free energy. EXPERIMENTAL PROCEDURE Samples were prepared by hot and cold-rolling vacuum-melted ingots of iron containing 3 pct Si to strips 0.012 and 0.006 in. thick. The ingots contained less than 0.005 wt pct impurities. The rolled strips were cut into samples approximately 1 in. wide by 3 in. long and were electropolished to remove surface imperfections. All samples were annealed in a vacuum at a pressure of approxi-

Jan 1, 1960