Search Documents

By B. Ramaswami, U. F. Kocks, B. Chalmers

This paper describes the tempetrature, solute (gold), and orientalion dependence of the plastic rleforlirnlion of silver single crystals. The virgin flow stress, To, and its temperatutre dependence incrense with increase in solute concentration. el decreases with decrease in temperature below room teiirperature and with increase in solute coucentralion. The dependence of 011 on temperature arid solute sontenl is due to the dependence of Ts on the two variables. An increase in ts, due to either the temperature or the solute conlent, results in a decrease of e11 in crystals of single-slip orientation and an increase of 011 in crystals of' (100) find (111) orientation. is orientation-dependent and at all the temperatures and in all the materials studied. The Leveling off of the engineering stress-strain curve in crystals of (100) 07-ientotion at a stress tl, is associated with extensive cross slib. The temperature and strain -rate dependence of tl are similar to those of indicating that a rate process is the cause 01 this phenomenon. The plastic deformation of silrer crystals of (110) orientation is multiple to that of crystals of single-slip orientation. THE work hardening of fcc crystals has been the subject of intensive investigations in the past 15 years. The effect of orientation, deformation temperature, solutes, second phase or precipitates, strain rate, etc., has been studied in a number of fcc metals.'-5 In spite of the considerable amount of work reported on the dependence of work hardening on the orientation, temperature, and solute concentration, certain aspects of the plastic deformation of fcc crystals have not been clarified. For instance, with the exception of a few investigations,6-8 where crystals of multiple-slip orientations have been studied, almost all the studies have been on crystals of single-slip orientations. Hence, a major portion of this study has been devoted to the dependence of plastic deformation on the multiplicity of slip systems and the enhanced possibility of dislocation interactions resulting from such multiplicity. Further, the abnormally low rate of work hardening observed at large strains at certain temperatures in crystals of the (100) orienta-tion 6-8has not been explained satisfactorily. It is the aim of this study to clarify this aspect of the orientation and temperature dependence of the plastic deformation of fcc single crystals. The work-hardening characteristics of single crystals of aluminum of ( 110) orientation have been studied at room temperatur "'12 and above." They have not been studied at temperatures where the virgin flow stress is dependent on temperature or where, in Seeger's terminology is important. The work hardening of single crystals of (110) orientation is of interest for another reason. As shown in Table I, the dislocation reactions that are possible in the (110) orientation are similar in certain respects to those that are possible in the (100) orientation. Hence, the deformation of single crystals of silver of (110) orientation was studied in the temperature range 100° to 900°K at intervals of 200°K. The effect of solute concentration on the plastic deformation of fcc single crystals of single-slip orientation has been studied by several investiaators.> In all of these investigations—with the exception of Ref. 20—single crystals of identical orientation have not been used, with the result that the orientation dependence of plastic deformation is superimposed on the effect of the solute. In addition, the effect of the solute on the work-hardening characteristics of single crystals of multiple-slip orientations has not been studied by the previous

Jan 1, 1965

By Evans B. Mayo

This study examines the structural framework of the Southwest for evidence of the four principal trends of lineament tectonics. It attempts to classify their intersections and compares the positions of those trends that appear most favorable with the positions of the presently known mining districts. This is a controversial topic. The author, in presenting his analysis, is aware that the study of lineament tectonics and relation of ore districts to regional structure is complicated by insufficient data and, unavoidably, by personal bias. The development of lineament tectonics has been summarized by Umbgrove.' Early attempts to fit ore districts into the Cordilleran framework were made by Billingsley and Locke, who do not refer to lineament tectonics, although their appoach is similar; they observe that heat and fluids, including the ore-depositing fluids, are most likely to rise at or near intersections of major structures where the crust is fractured, or weakened, to great depth. As a result of studies distributed over the earth-including ocean basins as well as continents— some tectonists recognize four dominant structural trends: 1) northwest; 2) northeast; 3) nearly east-west, or equatorial; and 4) nearly north-south, or meridional. Baker' proposed a theory to account for these trends and Sonder" called their world-wide arrangement the regmatic shear pattern. Moody and Hill proposed a much more complicated shear network which, although fascinating and perhaps ultimately useful, will not be followed here. In a recent review of deformation within the Cordillera, Wisser mentioned the four fundamental directions. The fact that many geologists deny the existence of the regmatic shear pattern implies that the fundamental structures are far from obvious. It may mean, also, that some geologists are not accustomed to examine regional and world maps analytically. The maps require much study, and certain features should be isolated on overlays. Even so, with the present limited knowledge, uncertainties remain. The following analysis is a qualitative experiment, subject to change as information accumulates, and should be supplemented by the western sheet of the Tectonic Map of the United States.' Many have probably gained the impression that the Cordillera of the West is oriented northwest-southeast and from this, unless experience rules otherwise, it is natural to assume that the structure likewise trends northwest-southeast. To an important extent this is true, yet anyone tracing off the western sheet of the Tectonic Map all the recorded north west-southeast structures may be surprised to see what a small part of the entire area they occupy. In southwestern U. S. (Fig. 1) the northwest-southeast structures are mostly restricted to the eastern, southern, and western parts. The eastern margin of the Cordillera from northern Colorado to the International Boundary near El Paso, Tex., is obviously determined by some structure other than northwesterly ones. In eastern Nevada and far southward toward the Gulf of California many mountain ranges, valleys, and faults are meridional. In the Rocky Mts. of Colorado, and at many places in southern Arizona, the crystalline Pre-Cambrian is foliated northeast-southwest. The Uinta Mts. of Utah trend approximately east-west, in much the same way as a broad belt of transverse, west-northwest structures—the Texas lineament of Hill",' and Ransome10 in southern Arizona, southwestern New Mexico, and southern California. It seems, then that there are four regmatic shear directions in the Southwest, but at many places they are discontinuous, and their projections must be inferred. To clarify these trends the four sets have been isolated into two systems: 1) northwest-northeast and 2) east-west-north-south (Figs. 2 and 3). Northwest-Northeast System: A number of prominent northwest-trending zones of structure are easily recognized. They are designated by circled Roman numerals, the northeast-trending structures by circled capital letters. Perhaps no two geologists would agree completely on the positions of all these belts. Names given below are for convenience only, and may be discarded where other names have priority. (I) The Sierra Nevada-Lower California belt contains the Jurassic-Cretaceous granitic massifs of the Sierra Nevada and Lower California. These

Jan 1, 1959

By N. S. Stoloff, R. C. Ku, R. G. Davies

The stress-strain behavior of Fe-Co and Fe- V alloys containing up to 25 pct solute have been studied in the temperature range 25° to - 196°C. The microyield stress is independent of temperature for all alloys studied, while the temperature dependence of the ordinary yield stress is large and comparable to that for unalloyed iron. An alloy-softening phenomenon is observed for many alloys relative to unalloyed iron, and appears to be a consequence of removal of inter-stitials from solution and their subsequent agglomeration. The ductile to brittle transition temperature is increased markedly by both cobalt and vanadium. Transmission electron microscopy observations reveal that cross slip and cell formation are restricted with increasing solute, which can account for many aspects of yielding and fracture behavior. IRON and other metals of bcc structure slip on many planes of the (111) zone at moderate and elevated temperatures, giving rise to wavy glide. At low temperatures, however, there is a tendency for slip to be restricted to planes of only one or two crystallographic types; in the case of Fe-Si alloys for example, (110) glide predominates, giving rise to planar slip bands."' Restriction of cross slip at low temperatures in iron has been linked by Brown and Ekvall3 to increased strain hardening in the preyield microstrain region, leading to an apparently large temperature dependence of the yield stress. Support for this view has been provided by Lawley and Gaigher4 from a transmission electron microscope study of molybdenum. They concluded that dislocations at lower temperatures, by virtue of their inability to change planes readily, are unable to interact and annihilate, leading to an increase in internal stress and work-hardening capacity. Restriction of cross slip at low temperatures has also been suggested to be an important factor in determining the ductile to brittle transition of single-phase solids, including metals of bcc structure.5 It is pertinent to note that most solute elements tend to raise the ductile to brittle transition temperature of poly crystalline ferrite,6,7 although in some cases, e.g., Fe-Cr7 and Fe-Al,8 the dilute alloys may actually yield at lower stresses than unalloyed iron. It appears, therefore, that solute elements may have an effect analogous to lowering the test temperature with regard to restricting cross glide. Such an effect has indeed been observed in the ionic alloy system KCl-KBr,9 in which bromine atoms, although causing little misfit and consequently little effect on the yield stress of KC1, have a pronounced effect in restricting wavy glide and inducing brittleness. The purpose of the present investigation was to determine the effects of selected solute atoms on the yield stress and fracture behavior of iron, and to elucidate in turn how the slip character was related to these properties. Since it is known that interstitial atoms exert a strong influence on the mechanical behavior of iron, the solute elements chosen for study were vanadium, which reacts strong with interstitials,10 and cobalt, which does not form highly stable interstitial compounds." EXPERIMENTAL PROCEDURE Four-pound ingots of each of the following alloys were vacuum-melted in zirconia crucibles: Fe-1, 5, 10, 25 at. pct Co, and Fe-1, 4, 10, 20 at. pct V. An ingot of unalloyed iron from the same original stock as that used for the alloy was remelted under similar conditions to eliminate variations in interstitial content arising from differing thermal histories. Chemical analyses of the iron, cobalt, and vanadium melt stock are listed in Table I. All ingots were rolled and swaged, commencing at 850°C, to 1/4-in.-diameter bar. The bars were then annealed at 850°C for 1 hr (except that the 10 and 20 pct V alloys were heated for 2 hr) to give a uniform equiaxed grain size of about 0.05 mm. Tensile samples of 0.125 in. diameter by 0.8 in. gage length were utilized for studies of the ductile to brittle transition. A second set of tensile samples were utilized for microstrain experiments in which strain sensitivity of 1 x 10"6 was achieved by a capacitance method.3 Cylindrical compression samples 0.250 in. diameter by 0.4 in. long also were prepared to study the influence of composition on the macroscopic yield stress, and for metallographic analyses of defor-

Jan 1, 1965

By Rollin A. Slater

This paper presents a composite of ideas on materials handling systems by describing the design of an over-all system for a hypothetical steel pellet plant located on the Great Lakes. The bulk materials handling industry has served for years as the skeleton and the central system of nerves and nourishment for the body of basic industries. During the past two decades, this body has undergone substantial growth and mutation to meet the surging demands of our national economy for more and better products. The steel industry has kept pace with spiralling demand by innovation which has resulted in new processes and improved designs which generally yield greater production from fewer units. Materials handling technology has likewise improved its techniques and currently has a new, stronger generation of equipment to perform its necessary supporting function. Drawing upon excerpts from several recent plant designs, this paper describes a basic approach to the selection and application of modern bulk materials handling systems to an entirely new steel plant. Specific details are not available for publication, and therefore the plant described herein is a composite of ideas. This imaginary plant will be located on the United States side of the Great Lakes and its owner will be called the Hypothetical Steel Corp. for purposes of discussion. TYPES OF EQUIPMENT The basic bulk materials handling systems and components required in a plant so situated are: lake boat unloaders; railroad train unloading systems; storage pile stackers and reclaimers; large bins and regulating feeders; and the conveyor systems — with their attendant controls— which connect the foregoing. PROGRAM OF DEVELOPMENT The initial work on the plant must be that of the process engineers who develop and refine the basic data, i.e., the logistics of all raw materials, waste materials and products within the plant. During this phase of study, the materials handling engineer may advance his planning only in basic areas such as movements at the dock and movements at the railroad. This initial planning work is concerned only with defining logical plant locations in the light of channels, currents, existing traffic, governmental regulations, locations of existing railroads and available rights-of-way. These systems alone have their own individual criteria which must be respected and accommodated in the final layout. All other elements, such as the arrangement of the blast furnaces, power house, coke plant, by-product plant, scrap preparation plant, BOF shop, and facilities for continuous casting, degassing, calcining, etc., are dictated by their own specific needs and their relation to each other. In the arrangement of these latter facilities, the materials handling system is secondary and must be designed to accommodate. BASIC LOGISTICS The result of the process engineer's work can be expressed in terms similar to those shown in Table I. Plants are customarily rated in terms of annual tons of ingots. Therefore, the basic size of this plant can be determined by referring to the BOF Shop wherein it is sized at 5 million tpy. From the base, the required hot metal can be traced to the blast furnace, which in turn indicates the amount of required flux, iron bearing materials and coke —which in turn establishes the demand for coal. Likewise, the total demand for flux can be determined by the combined demand of the lime plant and blast furnace. The generation of fines and waste products, which have significant value but are not usable as such, create the need for a sintering plant. From projections such as the foregoing, the complete flow of materials can be established and accommodated. The basic premise upon which this typical materials balance is predicted is that the plant will be a producer of high tonnages of non-SpecialtV- products. All basic raw materials (flux bearing, iron bearing, coal) will be prime quality. For example, the basic iron charge will be pellets, and the iron ore fraction will be sized lump, all of which

Jan 1, 1970

By J. V. Gluck, Ping-Wang Chiang

The tellurium-rich region of the Sb-TI-Te ternary system was investigated by means of DTA, metallo-graphic, X-ray, and electron beam microprobe techniques on the sections Sb2Te3-T12Te3, SbTlTe2-Te, SbT1Te2-Sb2Te3, and SbTlTe2-T12Te3. The phase behavior of this region is summarized in terms of four ternary invariant reactions and a schematic reaction diagram is suggested. Isopleths for the sections SbT1Te2-Sb2Te3, Sb2Te,-T12Te3, and SbTlTe2-Te were constructed, and a schematic diagram of the projections of the liquidus lines and invariant planes is presented. No evidence was found to support the existence of the ternary compound "SbTlTe3", or pseudo-binary behavior of the section T12Te3-Sb2Te3, as reported by Borisova and Efremova. Electrical conductivity, Seebeck coefficient, and thermal conductivity measurements were made at room temperature on fully annealed samples. 1 HE phase relationships in chalcogenides are often complex and difficult to resolve, particularly since the approach to equilibrium is a rather slow process. For example, the phase diagram of the T1-Te binary system was in doubt until clarified by Rabenau et al.,1 the phase fields at compositions near Bi2Te3 in the Bi-Te binary system have only recently been satisfactorily elucidated by Glatz,2 and there may still be some question as to the extent of the Sb2Te3 field in the Sb-Te system.3-5 In ternary systems, the existence of the compound "AgFeTe2" was the subject of a number of conflicting reports6-8 and the stoichiometry of the composition "AgSbTe2" was in doubt for a period of time.9 Recently, questions have arisen regarding the existence of certain compounds in the ternary systems Bi-Tl-Te10-14 and Sb-Tl-Te.15 The impetus for studies of these latter systems stemmed from the report of Borisova et a1.10 of a congruently melting ternary compound, "BiTlTe3", which apparently had extremely favorable thermoelectric properties for room-temperature cooling applications. Attempts by other investigators to produce the compound or confirm the transport properties proved to be unsuccessful.12-14 Recently, Chiang and Gluck14 reported studies of the phase relations in the tellurium-rich region of the Bi-T1-Te system which indicated that the section T12Te3-Bi2Te3 was not pseudobinary as suggested by Borisova et a1.10 The contention of Spitzer and sykes12 was supported that the composition "BiT1Te3" was multiphase, with the primary constituent actually being BiTlTe2, a compound whose existence has been well demonstrated.16,17 The investigation reported in the present paper was prompted by a later report of Borisova and Efremova15 on a similar study of the section T12Te3-Sb2Te3 from the Sb-T1-Te system. They also claimed this section to be pseudobinary, and that a ternary compound "SbTlTe," was formed peritectically. Some "preliminary" crystallographic data were given for the compound and thermoelectric transport properties were presented. In view of the questions concerning the behavior of the Bi-T1-Te system and the existence of the compound "BiT1Te3" it was suspected that the Sb-T1-Te system might behave in a similar fashion, particularly in light of the known existence of a compound SbT1Te2, iso-structural with BiT1Te2.17 Consequently, an investigation was undertaken to clarify the phase relationships in the tellurium-rich region of the Sb-T1-Te system. It is the purpose of this paper to present the results of this study, including a representation of the phase relations, isopleths for various composition sections, and the determination of some phase compositions and transport properties. EXPERIMENTAL PROCEDURES Commercially available high-purity (99.999+ pct) elements, purchased from the American Smelting and Refining Co., were used for the sample preparation. All samples were made from thoroughly mixed powders of previously prepared master alloys: SbTlTe2, Te, Sb2Te3, and T12Te3. Stoichiometric quantities of the constituents for each 10-g sample were weighed into a specially cleaned fused silica tube and sealed under a vacuum of better than 5 x 10-5 torr. The sealed constituents were fused and reacted at 650° to 750°C for at least 4 hr under continuous agitation in a "rocking" furnace, and the resulting product was air-cooled. The tube was opened and the sample was ground to a powder. A portion of the powder was rebottled in a DTA tube under vacuum, and the rest of the material was similarly resealed in a separate tube, re-fused in the rocking furnace, and again cooled to make the ingots for electrical and microstructural studies. All samples were subjected to further heat treatments as discussed in the section on experimental results. Each DTA tube was made of 7-mm-OD fused silica tubing with a concentric 2-mm-ID depression about 4 mm long formed in the bottom to accommodate a thermocouple. The size of a DTA sample was 0.5 to 1.0 g. An Aminco Thermoanalyzer whose accuracy was within 2°C18 was used for the DTA measurements. The metallographic samples were prepared by conventional techniques. A solution of FeCL dissolved in a methanol-HC1 mixture was found to be the most satisfactory etchant. Electron beam microprobe scanning and point-count examinations were made on polished and unetched samples using an ARL Electron Microprobe at an electron beam voltage of 20 kv. The detectors were set to receive characteristic La1 radiation. Calibration standards of the pure elements were incorporated in each sample mount; quantitative point counts were calibrated by a method similar to Ziebold

Jan 1, 1969

By K. G. Wikle, J. G. Klein, W. W. Beaver

Consolidation of hydride process, electrolytic, calcium reduced, and comminuted thorium powder, as well as saw chips and lathe turnings, by vacuum hot pressing and by cold pressing-vacuum sintering was studied. The mechanical properties of the consolidated material in the extruded form are compared with those of wrought castings. AT present there little little industrial use for thorium metal, although it has some important though small scale applications in electronic equipment. Despite its high inelting point—about 1750°C —a low modulus of elasticity, 11.4xl0 si at 20°C;' relatively low mechanical properties coupled with a high density, 11.7 g per cu cm; and an unusually high chemical activity with normal atmospheres limit any structural applications. The metal is utilized as an alloying element principally in magnesium. Pure thorium finds utility as electrodes in gaseous discharge lamps such as the high intensity mercury lamp' because its low work function and high electron emissivity provide lower starting potentials and more uniform operating characteristics than other available materials. The metal is also found in photoelectric tubes used for the measurement of the ultraviolet spectrum." Thorium metal has been used in germicidal lamps of the cold cathode type as sputtered coatings on nickel in order to provide a low work function surface and a low starting voltage. Other applications have involved the radioactive properties of thorium for the production of ionized particles." The potential value of thorium is much greater than its present use pattern because of possible utility in the field of nuclear power. Th may be converted through nuclear reaction to a fissionable element U which should be capable of acting similarly to U in the g'eneration of atomic power. Thorium has been reported to be about three times as plentiful as uranium in the earth's crust, placing it in the order of abundance of lead and molybdenum." Thus, it is of interest in augmenting the potential supply of fissionable material for nuclear power. Because of its high melting point, thorium is usually produced as a powder through the calcium reduction of its oxide or thermal reduction of halides by sodium, magnesium, and calcium. It may also be produced in flake form by electrolysis of fused alkali or alkaline earth chloricles and fluorides. Therefore, powder metallurgy assumes importance in the fab- rication of thorium metal shapes. Furthermore, it is rather difficult to obtain pure thorium by melting, as the molten metal reacts readily with graphite as well as oxide, carbide, and nitride refractories. These contaminate the melt with oxides, carbides, and metallic impurities." The current investigation was undertaken to examine the fabrication of thorium by powder metallurgy methods which have been used for the commercial production of beryllium and other metals.' A sparcity of data concerning the comparative cold and hot compaction of thorium powders of different derivation existed. Therefore, all commercially available types were examined along with other experimentally produced thorium powders in order to round out the comparison of consolidated thorium powders with melted reguline metal. Review of the Literature By heating a mixture of ThC1, with potassium, Berzelius made the first thorium metal as an impure powder in 1828. Improvements in the basic process, increasing thorium assay to 99 pct, were made by several investigators including Arsem," Lely and Hamberger10 and Von Bolton." Calcium reduction of Tho, to make powders was investigated by Berger," Huppertz,'" Kroll," and Kuzel and Wedekind.'" A thorium powder produced by this method using a CaC1, fluxing agent assayed 99.7 pct, as reported by Marden and Rentschler.'" Compacted and sintered, this product was found to be ductile, and could be fabricated into wire and sheet. Improvements of the calcium reduction process were made later" wherein CaCl, was eliminated from the reaction, producing metal assaying 99.8 pct Th. Further work by Lilliendah118 howed that a coarser metal could be obtained by the substitution of ThC1, or ThOC1, for oxide with consequent advantage of stability to atmospheric reaction. Reports on the technology of thorium developed in Germany during World War II have been made by Espe."' Thorium powder of 99.5 pct Th was obtained by reduction of the oxide by calcium. Screening to —200 mesh, compacting with about 20 tsi, and sintering in vacuo at 1320" to 1360°C for 3 hr resulted in a porous sinter cake. The sinter cake was sufficiently ductile to be worked into bar, wire, and sheet which could be employed as electrode materials.

Jan 1, 1957

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received' little study on the part of wire mills, particularly those that have commenced operations in the last few years.

Jan 1, 1930

By R. A. Wolfe, H. W. Paxton

Self-diffilsion coefficients for cr51 and Fe55 in 12 pct Cr-Fe and 17 pct Cr-Fe for Fe55 in chromium, and for Cr51 in vanadium have been measured. The results are compared with other values for the Fe-Cr system, and with the various theories of diffusion in hcc metals. Some empirical correlations are discussed between Do and Q in hcc systems, or, expressed differently, the constancy of ?G*/T solidus for seveval bcc metals and alloys is noted. It appears very probable that a vacancy mechanism is operative in bcc metals, hut this cannot he stated with certainty. THE great bulk of work on diffusion in metals, both experimental and theoretical, was for many years concentrated on those with close-packed and, in particular, fcc lattices.1,2 There appears to be little doubt that the mechanism of diffusion in these solids is vacancy migration, leading to mass transfer and in substitutional solid solutions to a Kirken-dall effect.3,4 For bcc metals, the picture is much less clear. The Kirkendall effect certainly occurs in several alloys.5-10 However, attempts to understand the factors contributing to the pre-exponential in the usual expression for the diffusion coefficient D =D, exp {-Q/RT) by extension of ideas useful in close-packed lattices have not always been successful. Zener,11 Leclaire,12 and Pound, Paxton, and Bitlerl3 have suggested that various forms of ring diffusion may be important in some bcc metals. For close-packed metals, Do is usually about 1 sq cm per sec and Q - 35Tm kcal per mole (Tm = melting temperature in OK). The theory of Pound et al. suggests for ring diffusion that Do may be about 10-4 and Q, although difficult to calculate with any precision, would be significantly less than 35 T,. The experimental results on self and solute diffusion in ? uranium14,15 and ß zirconium,10 and for solutes in 0 titanium,17 and possibly for self-diffu- sion in chromium below about 0.75 T,," gave some credence to this theory. However, not all bcc materials display low values of DO and Q, and the exceptions were not predicted by any theory. Furthermore, it has recently become apparent that, in bcc materials, log D is not always linear with T-l if a sufficiently wide range of temperature is studied.16,18 This variation may be such that Q may increase18,19 or decrease20 with increasing temperature. The present work was undertaken in an attempt to provide further diffusion data on bcc metals, and to try to understand the factors which contribute to differences in behavior between the various elements. For part of this work, the Fe-Cr system was chosen since it is of considerable technological importance, and data on 12 pct Cr and 17 pct Cr alloys appeared well worthwhile to supplement that existing for the remainder of the stern.18,22 The diffusion of Fe55 in chromium was studied as an example of a more or less "normal" tracer element in a possibly abnormal host lattice. Finally, no data were available for vanadium, the neighbor of chromium in the periodic table, because of lack of a suitable isotope so cr55 was used as a tracer in a few preliminary experiments. For convenience, we shall refer to elements whose Do and Q are low compared to those predicted by Zener's theory as "anomalous". PROCEDURE This investigation determined self-diffusion rates by means of radioactive tracers and the integral-activity method first utilized by Gruzin.23 In this method a thin layer of radioisotope of the diffusing element is plated or coated onto a planar surface of the diffusion sample, which is then given an isothermal-diffusion annealing treatment. The determination of an activity-penetration curve involves measuring the residual activity of the specimen after each successive layer or section has been removed parallel to the original planar surface. The method used here is essentially the same as that used by Gondolf18 and Kunitake.21 Two radioactive tracers, cr51 and Fe55, were used in this investigation. Diffusion coefficients were determined for the diffusion of one or both of these tracers in four different materials, viz., Fe-12 wt pct Cr alloy, Fe-17 wt pct Cr alloy, chromium, and vanadium. The diffusion samples had nominal dimensions of 1.5 cm diameter and 0.5 cm thickness. The grain size was several millimeters for the Fe-Cr alloys and at least 1 mm for the chromium and vanadium samples. Accurately planar surfaces

Jan 1, 1964

By D. S. Flett, A. W. Fletcher

Equilibrium studies on the extraction of nickel and cobalt with kerosine solutions of naphthenic acid have shown that an exchange extraction reaction occurs at pH 5.5. The nickel/cobalt separation factor is constant at 1.8 for constant total metal molarity and varying nickel/cobalt ratios. The separation factor decreases with increasing total metal molarity in the organic phase beyond 0.2 M and also decreases with increasing temperature. From the equilibrium data, it has been possible to derive a mathematical model for the separation of nickel from cobalt by exchange extraction in multistage systems. Experimental data from a continuously operated multistage mixer/settler apparatus has shown a reasonable correspondence with computer-calculated data. The effective separation of nickel and cobalt in sulfate solution remains a problem in hydrometallurgy and the hope that this would be solved by solvent extraction has not yet been fulfilled. With chloride solutions, advantage may be taken of the ability of cobalt to form anionic complexes with the chloride ion. It can then be readily separated from nickel, which does not form stable chloro complexes, by extraction with a suitable long chain amine. However, in hydro metallurgical operations, sulfate solutions are generally obtained in which no extractable anionic species are present. Thus, the possibility of using cationic extractants must be considered, and in this paper attention is directed to the use of carboxylic acids. The method of separation studied has been termed exchange extraction, which involves replacement of a metal in the organic phase with a more acidic metal in the aqueous phase. Thus, (BR2).+ (Az+)aqt=(AR,).+ (B2+)aq (I) where metal A is more acidic than metal B, R represents the acidic radical derived from the acid RH, and the subscripts e and aq refer to the organic and aqueous phases, respectively. Ashbrook and Ritcey' have used this method for the separation of cobalt from nickel using the sodium salt of di-2 ethyl hexyl phosphoric acid, which preferentially extracts cobalt. Some nickel is coextracted, and this is removed by exchange with cobalt ions in the feed solution by suitable countercurrent operation in a pulsed column. Much work has been carried out by a number of workers in Russia on the general use of exchange extraction for the separation of metal ions using car-boxylic acids. Gindin et aL a have demonstrated that this technique could be applied to the separation of nickel from cobalt using a C--C. carboxylic acid and have applied the technique to the production of high purity cobalt solutions for electrolysis. Further worka was concerned with the development of a process for the separation of nickel from cobalt in a pulsed column. This system permitted the separation of iron and copper from nickel and cobalt in one system. The procedure involved center feeding with acid backwashing at the top and alkali addition lower down the column. Thus the system operated under a pH gradient and the metals were distributed in the column in the order of their basicities. A similar application was studied by Gel'perin et al,4,5 for the removal of copper and iron impurities from a nickel anolyte by means of a C10-C,12 fatty acid fraction. Ginden et al,' and Fletcher and Wilson' have studied the effect of pH on the extraction of a number of metals with carboxylic acids. These studies showed that metals such as iron, copper, lead, zinc, nickel cobalt, and manganese are extracted at pH values close to the pH of hydroxide precipitation. Nickel is extracted at a slightly lower pH than cobalt and thus the nickel/cobalt separation factor has a value not much greater than 1. More basic work on complex identification has been reported by Fletcher and Flett: by Tanaka; and Jay-cock and Jones." These studies have suggested that at low loadings in the organic phase, the nickel and cobalt carboxylates appear to be dimeric and solvated by free carboxylic acid molecules. As the concentration of metal in the organic phase increases, the complex changes and larger polymeric species are formed. In order to permit assessment of the potential of carboxylic acids as extraction reagents for separation of

Jan 1, 1971

By W. B. Agocs

IN August 1954 a low altitude test geophysical survey was made in the Green Pond area of Morris County, New Jersey, with a Gulf Research and Development Co. Model II total magnetic field variation magnetometer mounted in a Sikorsky S-55 helicopter. The test was made in this area to compare the results of a high precision, very low altitude magnetometer survey with an existing ground magnetic survey in this area having known magnetite concentrations, so that the method could be used in areas of difficult access for the detailing of airborne magnetometer anomalies of interest in place of ground surveys. The load capacity of the Sikorsky S-55 permitted installation of a recording scintillation counter so that a radioactivity survey would be made simultaneously with the magnetometer survey. The area surveyed is located at approximately 41°00'N and 74o28'W, just south and east of the town of Green Pond, N. J. The outstanding topographic feature of the region is Copperas Mountain, a well defined ridge, maximum elevation 1222 ft, which runs the entire length of the survey. The lowest point in the survey, 810 ft, is in the extreme eastern corner. Topography of the area is shown in Fig. 1. The three major rock units outcropping in the area are all metamorphic: the Pochuck gneiss, which has been divided into two metamorphic facies; the Byram gneiss; and the Green Pond conglomerate. The relative ages of the Pochuck and Byram formations, both pre-Cambrian, are in doubt, but it is believed that the Pochuck is the older of the two.' The Green Pond conglomerate is Silurian.' Distribution of the outcrops and mine locations is shown in Fig. 1. Two facies of the Pochuck gneiss can be distinguished locally—the Copperas Mountain and Kitchell members. The Copperas Mountain member is a hornblende gneiss, and all the mines and prospects in the area are in this unit. The Kitchell is a quartz-plagioclase feldspar gneiss. The Byram gneiss is a relatively nonresistant valley formation which is high in the potash feldspar. The Green Pond conglomerate is a well indurated quartzite-conglomerate which forms the Copperas Mountain and the Green Pond Mountain's ridge to the north. It overlies the gneisses with a strong angular discordance that may be a fault. The geologic structure of the Green Pond area is relatively uncomplicated. The foliation planes of the gneisses dip steeply to the southeast, and the Green Pond conglomerate dips steeply to the northwest. Additional faulting in the area is indicated at the contact between the Kitchell member of the Pochuck and the Byram along the base of the topographic spur extending to the southeast from Copperas Mountain. The magnetite mines of Pardee, Winter, Davenport, Green Pond, Copperas, and the Bancroft shaft are described by Bayleyl and Stampe2.' The ore is in the Copperas Mountain member of the Pochuck gneiss. The magnetite veins are 10 to 50 ft wide and up to 300 ft long, dipping to the southeast at angles ranging from 40" to 75". The locations of these mines are shown in Fig. 1. Dip Needle Survey: The dip needle survey shown in Fig. 2 was taken from a U. S. Bureau of Mines Report of Investigations." The figure numbers below the local, individual map area outlines refer to the figures in the aforementioned reports which were not contoured. The area of the dip needle survey was confined almost exclusively to the outcrops of the Pochuck gneiss. The separation between survey profiles was 100 ft and the distance between stations on the profiles was 25 ft in highly anomalous zones to 100 ft in magnetically flat areas. A total of 16 1/2 miles of traverse was surveyed over an area of approximately 1/2 sq mile with 2050 stations. The magnitude of the magnetic anomalies is difficult to determine due to the lack of information concerning the type of dip needle used and the procedure followed in making the dip needle survey. This latter would include the method of "zeroing" the dip needle and the procedure of reading at the stations, whether on the swing or statically. Calibrations made of the Gurley dip needle, Lake Superior type, show a static sensitivity of 385 gamma per degree in the range from —25" to +35o, corresponding to a variation in the total field of —9600 gamma to +13500 gamma in a total field of 57000 gamma, inclination 72". The sensitivity increases to 16 gamma per degree from a deflection of 60" to 76", and from 76" to 172" the sensitivity decreases continuously to a low of 260 gamma per degree. From the above it may be seen that it is difficult to assign an arbitrary sensitivity for the dip needle used on this survey. However, an estimated value of 100 gamma per degree may be assigned. On this basis, the majority of the magnetic anomalies, whose deviation is +20°, would be 2000 gamma. Locally, west and northwest of the Pardee mine the magnetic anomaly is +50°, or 5000 gamma; in the Green Pond mine area deviations of +75" are observed that would correspond to anomalies of 7500 gamma. The areal extent and width of the dip needle magnetic anomalies is comparable to profile and station spacing. Hence it is concluded that part of the detail may be due to control, and the probable cause of the magnetic anomalies is at or near surface exposures of magnetite concentrations in the form of veinlets and disseminations whose locations correspond to the local magnetic anomalies. On the basis of the magnetics, none of the magnetite concentra-

Jan 1, 1956

By R. P. Laforce, ZJ. R. Low, A. M. Turkalo, D. F. Stein

The interaction of the crlloying eletnenls, nickel and chromium, with the impurity elements, antimony, pIzosphorus, tin, and arsenic, to producse reversible temper brittleness in a series of high-purity steels containing 0.40 wt pct C has been investigated. The alloyed steels contained approximately 3.5 pcl Ni, 1.7 pct Cr, and 0.05 to 0.08 pct of the particular irnpurity to be investigated. Susceptibility to teirlper embrittlement was measured by comparing the notched-bar transition temperature of each steel after quenching from the final temper and after very slow cooling (step cooling;) following the final temper. A plain carbon steel without alloying elements, bu/ ud/h 0.08 pel Sh, does not embrittle when step-cooled through the emzbrittling range of temperatures. The same embrittling treatment, applied to a steel with about the same antinzony content but with nickel and chvonziunz added, causes a 700°C increase in transition temperature. If chromium or nickel is the only alloying element, the increase in transition temperature is only 50%, again with antimony present. A carbon-free iron containing nickel, chromium, and antimony shou~s a 200°C shift in transition temperature for the same thermal treatment. Specific alloy-impurily interactions are also observed for the other impurity elements, phosphorus, tin, and arsenic. Additional investigations involving electron microscopy, trzicrohard-ness tests of vain boundaries, minor additions of zirconiutn and the rare earth and noble metals, nzainly with negative results, are also described. HE particular type of embrittlement investigated is that which is encountered in alloy steels tempered in the temperature range from about 350" to 525'C or slowly cooled through this range of temperatures when tempered above this range. This type of embrittlement is sometimes called reversible temper brittleness to distinguish it from the embrittlement indicated by a minimum in the room-temperature V -notch Charpy energy vs tempering-temperature curve encountered in the range 28 0" to 350°C. Temper brittle-ness seriously restricts the use of many alloy steels since it precludes tempering or use in the embrittling range of temperatures and may significantly raise the ductile-brittle transition temperature of heavy-section forgings and castings tempered above the embrittling range, since such sections cannot be sufficiently rapidly cooled after tempering to avoid embrittlement. The very voluminous literature of temper brittle-ness up to about 1960 has been reviewed by woodfine' and LOW.' Of particular significance to the present investigation was the demonstration by Balajiva, Cook, and worn3 that high-purity Ni-Cr steel does not exhibit temper brittleness and the subsequent detailed and systematic study by Steven and Balajiva~ of the effect of impurity additions on the susceptibility to embrittlement of Ni-Cr steels. Steven and Balajiva showed that, of the impurities which may be found in commercial steels, Sb, As, P, Sn, Mn, and Si could all produce temper brittleness in a high-purity Ni-Cr steel. The principal purpose of the present investigation was to study the effects of particular alloy-impurity combinations on susceptibility to temper embrittlement. The steels used were high-purity 0.30 to 0.40 wt pct C steels containing 3.5 wt pct Ni and 1.7 wt pct Cr, separately or in combination. The susceptibility of these steels was then determined when approximately 500 ppm by weight of antimony, arsenic, phosphorus, or tin were added as an impurity. The melting, casting, and forging practices used in the preparation of the materials investigated are described in Appendix A. Table A-I in this appendix shows the analysis of all steels to be discussed. The steels were produced as 20- or 2-lb heats. The smaller heats were used after it had been demonstrated (see Appendix B) that a small, round, notched test specimen could be used to measure the shift in the ductile-brittle transition temperature caused by temper brittleness with about the same result as that obtained by Charpy testing. HEAT TREATMENT Unless otherwise noted, all steels were tested for embrittlement in the tempered martensitic condition. A typical heat treatment for a 0.40 C, 3.5 Ni, 1.7 Cr steel was: 1 hr at 870"C, in argon, quench into oil at 100"C, quench into liquid nitrogen, temper 1 hr at 625"C, and water-quench. The warm oil quench was used where quench-cracking was encountered; otherwise the initial quench was into room-temperature oil or water. For other compositions austenitizing temperatures were 50°C above Acs with the remainder of the thermal cycle the same. Steels in this condition, with no further heat treatment, are designated as non-embrittled. The above quenching and tempering cycle for the 0.40 pct C steels resulted in as-quenched hardnesses of 48 to 53 RC and as-tempered hardnesses of 24 to 31 Rc except in the case of the plain nickel or plain carbon steels. In these, the as-tempered hardness was as low as 80 to 90 Rg. No attempt was made to adjust the tempering temperature to obtain the same hardness in ali steels since it was felt that a uniform thermal cycle was more important than exactly equivalent hardness values. Pro- the standard quench and temper described above, the standard embrittling treatment was "step-cooling". For this the thermal cycle was: 593"C, 1 hr; furnace-cool to 538"C, hold 15 hr; cool to 524"C, hold 24 hr; cool to 496"C, hold 48 hr; cool to 468'C, hold 72

Jan 1, 1969

By R. W. Raymond

This name is applied to the present mining law, as enacted in 1872 and since, to indicate its leading characteristic—in which it differs from all previous mining laws of this or any other country. The earlier act, passed in 1866, was practically the first attempt of Congress to deal with the question of mining titles upon the public domain. It was framed after nearly twenty years of acquiescence on the part of the Government in the self-constituted tribunals, officials, rules, and customs of the mining districts. In its recognition of these, and in several other particulars, the act of 1866 was open to serious criticisms. It is the purpose of this paper, not to trace the history of legislation on this subject, or show in detail what were the faults of the earlier law, but rather, by a discussion of certain aspects of the present law, to point out how great a revoluition it has effected in the rights of mining locators, and to indicate some of the difficulties attending its application. In the attempt to correct the vagueness of the act of 1866 an entirely new elernent was introduced into the law, bringing with it a new set of difficulties. Under the act of 1866 and the miners' customs which it followed, the lode was the thing claimed and subsequently acquired by patent. And the claim to a given number of feet on the longitudinal course of the lode was rooted in 'a discovery of any part of the lode in any part of the claim. ("Extensions" could in many districts—perhaps universally—be located and claimed on the strength of the discovery in the principal claim to which they referred; but this is a point not essential to the present discussion.) It was not necessary to find the outcrop or the upper edge of a lode in order to lay a valid location upon it. An explorer, sinking a shaft and intersecting a lode not already discovered and claimed by another, could claim by that discovery the number of feet along that lode which the local laws might permit (not exceeding the maximum set by the United States statute) whether his sur-

Jan 1, 1884

By T. A. O’Hara

SINCE May 1948, when tungsten carbide bits were introduced at the Flin Flon mine, they have been popular with the miners because of their fast drilling speed and low gage loss. The high cost of commercial carbide bits and tipped drill steel, however, prevented their use except for the hardest rock. In an effort to extend the use of tungsten carbide on a basis economically competitive with detachable steel bits, experimental work was begun in 1950 to test the feasibility of making tungsten carbide tipped drill steel in the mine drill steel shop. This work showed that tipped drill steel could be made locally at less than half the cost of the commercial product. The performance of the local tipped drill steel was comparable to that obtained with commercial carbide bits and tipped drill steel and the cost per foot drilled was much lower. Local tipped drill steel was adopted for all mine drilling in November 1951. Since then drilling costs per foot have been sharply reduced and footage drilled per manshift has increased markedly. Experience at Flin Flon has shown that production of satisfactory carbide tipped drill steel is not difficult and that highly skilled labor and costly equipment are not required. As long as wise selection of brazing materials is made and certain simple precautions are rigidly maintained, there is no reason why small mines with relatively unskilled labor cannot produce a satisfactory product. The following description outlines the technique used at Flin Flon for making carbide tipped drill steel and discusses characteristics of the brazing process that make special precautions necessary. Drill steel is forged to four-wing shape in a conventional steel sharpening forge. Standard steel dies are modified to minimize forging cracks around the central waterhole and to forge a blunt bithead on the steel. The steel is preheated to 1500°F and held at this temperature for at least 2 min. When the temperature has equalized throughout the steel section, the drill steel is transferred to the forging furnace and heated rapidly with a reducing flame up to 2000°F. This two-stage method of heating minimizes the grain growth and decarburization of the steel while ensuring that the steel temperature does not vary greatly throughout the forging zone. After forging the steel is allowed to cool in air to about 1600°F before being annealed in a bath of vermiculite. Despite the high hardenability of the 3 pct Ni-Cr-Mo drill steel used, this simple treatment anneals the drill steel sufficiently for milling. The forged and annealed drill steel is slotted on a plain horizontal milling machine that is equipped with a quick opening chuck and a slot depth stop. The full depth of the slot is milled in a single pass of the 3-in. milling cutter which is fed at 33/4 in. per min across the crown of each bit wing. The slots are cut to a width of 0.342 to 0.344 in. Maintenance of this slot width is necessary to ensure that the optimum brazing clearance of 0.002 in. will result after assembling of shims and carbide in the slot. Prior to March 1953, when the milling machine was installed, drill steel was slotted on a small manually fed ¾ hp milling attachment mounted on the bed of a lathe. Over 16,000 drill steels were slotted on this unit, and in view of its small size and low cost it gave excellent service. Brazing of Tipped Steel Drill steel that has been milled and cleaned in carbon tetrachloride is mounted in a rotating cradle holding six drill steels, the length of which may be from 2 to 12 ft. The slots in the drill steel, the shims, and the tungsten carbide inserts are thoroughly fluxed with a fluoride flux and assembled as shown in Fig. 1. Fig. 2 shows the brazing equipment in use. As the ring burner is lowered over the bithead a spring valve opens the gas lines, and the gas mixture, preset to give a slightly reducing flame, is fed to the ring burner where it is lit from a pilot flame. The ring burner heats the drill steel over a zone about 1 to 2 in. below the bithead, which becomes heated by conduction through the steel. By this means the bithead is heated rapidly and evenly, and contamination of the brazing joint with soot from the flame is avoided. The bithead is heated to the melting temperature of the brazing alloy within 1 min. This rapid heating minimizes the disadvantage of a non-eutectic brazing alloy. The brazing alloy, a nickel-bearing quaternary alloy, is placed at the bottom of the slot below the carbide insert, as shown in Fig. 1. As the brazing alloy melts it is drawn by displacement by the carbide and by capillary action into all parts of the joint to displace liquid flux from metal surfaces. As soon as the brazing alloy melts, each insert in turn is wiped by being moved back and forth along the slot. This action assists wetting of the carbide by the brazing alloy and assists in displacing molten flux from the joint. After continuous heating for about 75 sec, when the bithead has reached a temperature of about 1500°F, the ring burner is raised and the gas supply is shut off automatically by the spring valve. As soon as heating is stopped a hand press is placed on the bithead and the inserts are squeezed down firmly. This action minimizes the clearance between the bottom of the insert and the slot. Correctly brazed steel should maintain a clearance at the bottom of the slot of 0.001 to 0.002 in. After six steels have been brazed they are removed from the cradle and allowed to cool in air. As soon as each drill steel is cool it is dressed on a grinding wheel to remove excess flux and braze and is ground to the gage appropriate to the length of the drill steel.

Jan 1, 1955

By J. Nagy, D. W. Mitchell, E. M. Murphy

In 1957 research was initiated in the U.S. Bureau of Mines experimental coal mine near Pittsburgh, Pa., to study factors affecting foam generation and transport, to evaluate the effectiveness of high-expansion foam for controlling mine fires, and to develop techniques for applying the method under U.S. mining conditions. These investigations showed that high-expansion foam containing at least 0.2 oz of water per cu ft of foam is effective in controlling experimental underground fires burning coal, wood, and oil. Sometimes the fire was completely extinguished, but more often, it was brought under sufficient control to permit either a direct attack on the fire with a stream of water or loading of the hot material into cars. A progress report' prepared in July 1958 summarized the initial achievements of the USBM experiments. Since then other phases of the foam-plug method for attacking fires have been studied in the laboratory and in the mine. Previous studies by British engineers' of the foam-plug method for fighting mine fires indicated that high-expansion foam was effective in controlling experimental timber fires in an underground passageway. Their subsequent workx-1 pertained to the practical aspects of fighting large fires within a mining area with a foam-plug. CONTROLLING EXPERIMENTAL FIRES In the USBM tests foam was formed by spraying a dilute solution of a foaming agent on a metal or cotton net of 1/8 to 1/4-in. mesh. Air passing through the continuously wetted net forms bubbles of 1/2 to 11/2-in. diam and produces a honeycomb of foam that fills the passageway. Under the ventilating-air pressure, this light-weight plug moves forward through the passageways, around sharp corners, and over obstacles. as illustrated in Fig. 1. High-expansion foam was transported to a wood fire, an oil fire, and 13 coal fires. Figs. 3 and 4 show a typical coal fire before and after attack with foam. In 12 of the 15 experiments the fire was brought under control when the water content of foam was 0.2 oz or more per cu ft. A fire was considered controlled when the flames were quenched and observers could cross the area without wearing breathing apparatus or protective clothing. In the other three experiments, conducted when the water content was less than 0.2 oz per cu ft of foam, the flames were retarded but the fire was not controlled. Coal fires have been attacked successfully by foam introduced at points varying from 155 to 1010 ft from the fire. The time of burning in coal beds 10 in. thick ranged from 11/2 to 5 hrs or more. Most of the experimental fire beds were 15 ft in length. However, in one experiment a floor fire 25 ft long and 5 ft wide was constructed $5 upwind from another fire 15 ft in length; in another instance, the fire was 100 ft long and 5 ft wide. Foam was applied to the fires for periods ranging from 7 to 36 min. The time required for foam application depends on the extent of the fire, time of burning, water content of foam, foam velocity, and degree of fire control desired. In addition to the coal fires, foam was transported to a fire covering 45 sq ft, produced by 15 gal of oil burning in metal trays on the floor. The foam extinguished the oil fire in about 1 min. In one other test, the burning of 1100 lb of dry sawmill slabs stacked in open cribs 4 ft high and 16 ft long was brought under control by foam in 2 min. Composition of Gases in Return Air: In several of the experiments samples of the return air from fire zones were collected; composition of the atmosphere before, during, and after foam application was then determined. Because of condensation in the relatively cool sampling tube, the amount of water vapor was not determined. Analyses showed that concentration of carbon dioxide and combustible gases increased as the foam began passing over the fire. This resulted from the decrease in the volume of air when foam generation started and from the formation of gases when water reached the fire.* The quantity of gases generated would not be greater than that from an equivalent amount of water applied directly to the fire. The highest total concentration of combustibles (CO, CH1, and H2 mixture) obtained during the experiment was about 2 pct; this occurred 6 min after foam reached the fire. This atmosphere was nonex-plosive, but calculations show that if the air flow were reduced to about 5 fpm and if the rate of gas liberation from the fire remained constant, the mixture would be explosive. The use of foam on a fire in all probability would affect the normal ventilation of a mine. If the mine is gassy, this factor must be carefully considered before the foam is applied. APPLICATION OF THE FOAM-PLUG TECHNIQUE IN MINES Equipment and procedures for applying the foam-plug methods must be adapted to the prevailing conditions at a particular mine. Some factors to be considered in developing equipment are: size or extent of the mine, dimensions and number of entries, ventilation system, mining methods, haulage facilities, availability of water, amount of methane liberated, and existing fire-control apparatus. • In most experiments the initial air velocity of 200 fpm decreased to 50 to 100 fpm as the foam plug increased In length.

Jan 1, 1961

By E. C. Bain, E. S. Davenport

When annealed carbon, or low-alloy, steels are suitably heated the ferrite (alpha iron solid solution) and the carbide, of which they are composed, react together to form a single solid solution of carbon (and other elements) in gamma iron (austenite). This reaction may begin only at a certain minimum temperature called the eutectoid temperature. The first ferrite and carbide thus to react together do so in definite proportions known as the eutectoid composition. With further heating the original constituent that is present in excess is dissolved in the austenite until exhausted. Whether the excess constituent be ferrite (hypoeutectoid steels) or carbide (hypereutectoid steels) the procedure is much the same, and upon slow cooling the homogeneous austenite expels the excess of either (proeutectoid ferrite or carbide) until the eutectoid composition is reached. Thus the reaction upon heating is strictly reversed upon cooling and accordingly an equilibrium diagram of this process may be constructed. Such an equilibrium diagram concerns itself only with the temperatures involved and with the proportions and compositions of the phases developed under conditions that suffice to permit equilibrium. Specifically it has no concern for the type or mode of distribution of these constituents nor with any extra-equilibrium conditions such as undercooling, which is almost universally encountered in metals. Actually, however, of great importance is the sluggishness toward equilibration caused by the not inconsiderable time involved in diffusion. Thus instead of the theoretical transformation point AF, we find for a certain rate of heating or cooling the use of the designations Ar and Ac (transformation temperature found on cooling and upon heating). These figures obviously have no particular meaning except as measured and expressed for a definite heating or cooling rate, and represent the apparent temperature displacement caused by an inadequate time allowance. In this paper are presented the results of a study of the time required for the transformation of austenite to ferrite and carbide at a variety of temperatures and also of the time required for the reaction austenite? martensite at the temperatures at which this reaction occurs instead of

Jan 1, 1930

Jan 1, 1912

By Donald E. Meyer

High current-low voltage EB-gun evaporation in an oil-free ultra-high vacuum system was found to be necessary, though not sufficient, for stability (300°C, 106 v per on) of aluminium gate MOSFET's and MOS capacitors not stabilized by a phosphorous glaze. five characteristics of the equipment used: 1) Vacuum purification of the aluminum charge, 2) Ionization of the evaporant by the electron beam, 3) X-ray formation, 4) Residual gases during evaporation, and 5) Metal film structure were studied as Possibly significant in MOS fabrication. EVAPORATION of contact metals common to the semiconductor industry historically has been accomplished with oil diffusion pump systems and various resistance heated evaporant sources as dictated by the type of metal evaporated. To meet a need for greater reliability of semiconductor devices, other metallization methods were developed. A good example would be application of the moly-gold contact system to integrated circuits with deposition by RF or triode sputtering.' More recently, fabrication of stable metal-oxide-silicon devices and circuits has put new demands on metallization. The purity of the thin metal films composing MOS structures is critical, particularly at the metal-oxide interface, and ultra-high vacuum metallization using sputter-ion pumping and electron beam gun (EB-gun) evaporation are well suited for the task. At this laboratory aluminum has been the most common contact-gate metal for both MOS capacitors and MOSFET's. In the earliest work with MOS capacitors, aluminum was evaporated from wetted tungsten filaments using both diffusion pump and ion pump vacuum systems. In spite of clean oxide techniques these capacitors were unstable under bias-tempera-ture stressing. Only after a switch to EB evaporation of aluminum were stable capacitors produced. Using the same techniques it was possible to make MOSFET's with equivalent stability. Stability data for a discrete MOSFET is shown in Fig. 1. This is a "clean" oxide gate (no phosphorus stabilization or no etch back of a thicker gate) having a thickness of lOOO? thermally grown on the (111) plane. Gate length after diffusion was 0.24 mils, and the devices were hermetically sealed. Stressing conditions were 300°C and 106 v per cm applied alternately as a positive and negative field for 10 min, 50 min, and 4 hr for a total stress time of 10 hr. An initial shift in turn-on voltage of 0.1 v was detected for 10 min of positive bias. All evidence at this laboratory indicated that while EB-gun evaporation of ultra-high purity aluminum was not sufficient for 300°C stability, it did seem to be necessary. There may well then be something inherent in the EB-gun deposition used which enhanced stability, and probably no single factor existed but rather a series of factors. It is the purpose of this paper to report on some of the investigations carried out to learn more about EB-gun evaporation in ultra-high vacuum systems. EXPERIMENTAL DESCRIPTION The EB-gun was self accelerated, had a maximum power rating of 10 kw, and used a water-cooled copper crucible able to hold a 20-g aluminum charge. The electron beam was bent 180 deg and focused by an electromagnet which also provided movement of the beam across the crucible. Normal power conditions in this work were 9 kv and 300 to 600 mamp. The gun can be described as high-cur rent/low-voltage and was quite different in its mechanism of operation from EB-guns with much higher acceleration potentials. An oil-free vacuum system capable of 5 x 10- l0torr, a quartz crystal rate and thickness monitor and a quadruple mass spectrometer completed the evaporation system, Fig. 2. A typical evaporation cycle consisted of a 3 to 4 hr pumpdown to the upper l0-9 range and evaporation at l0? per sec with the pressure in the bell jar not rising above 1 x 10"7 torr. Thickness control was 5 pct or less and could be automatically monitored and controlled. Five phenomena associated with the EB evaporation and considered as possible contributors to Ma performance included a purification effect, ionization of evaporating aluminum, X-rays, constitution of vacuum ambient during evaporation, and film structure dependence upon evaporation rate. These phenomena are now discussed. Vacuum Purification. The design of the EB-gun permitted purification of the aluminum charge by vacuum outgassing. Particular features included an efficiently water-cooled copper hearth with a capacity of over 20 g of aluminum and the capability for sweeping the beam across the charge. Such capacity meant that aluminum had to be added only after about every fifth evaporation. A new charge was not required each evaporation as is necessary with filament evaporation. An oxide "scum" which appeared on the charge could be completely cleared from the top hemisphere of the charge by sweeping with the beam prior to opening the shutter. An indication of the purifying effect was obtained by a series of analytical measurements on incoming aluminum, after melting but with little vacuum out-gassing, after 30 min outgassing, and the evaporated film itself. Either a solids (spark source) mass spectrometer or an emission spectrometer were used for analyzing the aluminum charge. Analysis of the evapo-

Jan 1, 1970

By C. D. Williams, C. E. Ells

The susceptibility of quenched and aged Zr-2.5 wt pct Nb alloy to embritt2ement during irradiation has been examined for a number of solution temperatures and aging times. Material quenched from temperatures approximately 40°C below the transus has high tensile ductility, and this ductility is insensitive to aging at 500°C or to irradiation. If, however, the material is quenched from temperatures above the transus it becomes highly susceptible to loss of ductility either from aging at 500 or from irradiation. Inter granular failure is characteristic of the materials having low ductility. The distribution of the equilibrium phase is found to control the susceptibility to embrittlement by restricting 6 grain growth during heat treatment and thus influencing crack propagation. IN zirconium, as in titanium, -stabilizing alloy additions are used to obtain high strengths via quench and age heat treatments, and the Zr-2.5 pct Nb alloy has been developed1 because of its strength advantage over the Zircaloys. Early in the development of the Zr-2.5 pct Nb alloy the problem of 13 embrittlement was appreciated, and for this reason the solution temperature was chosen below the p transus.' In the course of irradiation studies on quenched and aged Zr-2.5 wt pct Nb alloy it was found' that irradiation introduced an important aspect of p embrittlement, riz., material quenched from the phase and aged 24 hr at 500°C was severely embrittled by moderate doses of neutron irradiation. This effect had not been studied in titanium alloys. In titanium the metallurgical features leading to 0 ernbrittlement were found to be structures with: a) coarse a platelets at the grain bondaries, b) finely dispersed a uniformly distributed throughout the (0) matrix,6 c) Widmanstatten a-13 with more than 50 pct P, d) the presence of some metastable p transformation products,3 and e) large prior -phase grain size.5 Alternatively, the presence of a uniform distribution of coarse a was conducive to high ductility and a structure largely of equiaxed a was very dctile. The detailed mechanisms of the embrittlement have not been worked out for all of these conditions, although weakness at either a-matrix boundaries or prior p grain boundaries have been prominent in the eculation. It was proposed that acicular a might act as a mild notch, and low ductility has been associated with easy fracture along its boundary.' There have been two opposing suggestions for the source of the high ductility associated with equiaxed a phase. JaffeeB proposed that this a would accept a large por- tion of the oxygen, thus increasing the ductility of the matrix, whereas after study of a Zr-Nb-Cu alloy Weinstein and oltz proposed that the a phase, softer than the martensitic matrix, acted to blunt cracks formed in the matrix. In the present work we have studied the effect of neutron irradiation on the ductility, particularly the P embrittlement, of the Zr-2.5 wt pct Nb alloy. By a variation of solution temperature and aging time a variety of metallurgical conditions have been examined, and a range of resultant ductilities obtained. The ductility has been related to the material microstructure and mode of fracture. EXPERIMENTAL The alloy used in the present work came from two separate ingots fabricated into rod of 3/8 or i in. diam, Table I. For both batches the P transus temperature was approximately 890° C. Most of the heat treatments were done directly on lengths of the j} in. diam rod, after which the tensile test specimens were machined. Quenching was achieved by dropping rods from a dynamic vacuum into water, the cooling rate estimated to be 2 100°C per sec. For aging the rods were encapsulated in evacuated silica tubes. Round tensile test specimens, with gage diam and length 0.160 and 1.0 in., respectively, were used throughout and pulled at room temperature or 300°C on Instron tensile machines, at a crosshead speed of 0.05 ipm. Specimens were irradiated in the NRX and NRU reactors, in facilities described in previous publications.'0 The metallurgical conditions examined have been: All tensile test specimens were machined with axes in the axial direction of the swaged rod. Although the specimen had a degree of preferred crystallo-graphic orientation with basal plane normals both parallel with and perpendicular to the tensile axis, the material was comparatively isotropic." The techniques of thin foil examination in the electron micro-

Jan 1, 1970

By A. U. Seybolt, V. A. Phillips

Binary iron alloys containing 1 pct of Al, Cr, Mn, Mo, Si, Ti, or V, and 0.4 pct C, 1 pct Cr steels with and without 1.2 pct A1 or 2.0 pct Ti additions, were ion-nilrided at 550° to 600° in N-H mixtures. Nitriding increased the inicrohardne ss of all the binary alloys except those containing manganese or molybdenutn, and also hardened the heat-treated steels if aluminum or titanium urns present. Transmission electron microscopy revealed particle formation in all casts where hardening occurred. Electron diffraction gare positive identifications for ALN, CrN, and a, Si3N4 in the binary alloys, and AlN and CrN in the aluminum- cold chromium-bearing steels, respectil&apos;uly. Cubic VN with a, = 4.13A was tentatively identified. Particles, apparently of CrN, also formed in the base steel but did not increase the hardness very much. Chromium and vanadium formed nitride platelets on {001}° matrix planes, while titanium gave clusters <15A diam. Aluminum nitride precipitated at grain and subgrain boundaries, and within the grains. Silicon gave profuse precipitates of several Morphologies at grain boundaries and cubical particles within the grains. No effect of the alloy carbides on nitride precipitation was observed in the heat-treated steels. THE nitriding of steel has been a well-established commercial process for about 40 years, but in spite of this comparatively long period of use there have been few studies aimed at understanding the process. Most studies, like the early but very competent work of Jones and organ&apos; and nones.&apos; were concerned with establishing the pertinent engineering variables of steel composition, gas composition, temperature, and time. As far as the present authors are aware, there have been no studies of the composition, size, shape, or distribution of the nitrides formed in the nitriding of steel. Noren and Kindbom3 did, however, examine a few nitrided steels by surface replica electron microscopy, and were able to show the presence of car-bonitrides and AlN and TiN nitrides. pitsch4,5 and Hrivnak6 examined nitrided pure iron by transmission electron microscopy. Baird7 found manganese nitrides in Fe-1.6 pct Mn when nitrided at 650°C, using the same technique. In the present work, emphasis was placed on transmission electron microscopy because of its inherently better resolution, using principally binary alloys of iron containing 1 pct of alloying element. In addition, a few simple 0.4 pct C steel compositions were examined to investigate possible carbonitride formation. It was not anticipated that all of the added elements would form nitrides under the conditions used, but it was considered desirable to obtain direct experimental evidence on this point. It would be considerably easier to ascertain the presence of alloy nitrides by examining appropriate binary alloys in preference to relatively complex steels. The work reported here could have been done using orthodox ammonia-nitriding procedures, but an operating ion-nitriding equipment was available, and was therefore used for specimen preparation. EXPERIMENTAL DETAILS 1) Materials. Binary alloys were made up from vacuum-melted electrolytic iron with 1 wt pct additions of Cr, Ti, V, Al, Mn, Mo, and Si of about 99.9 pct purity. In addition, three steels were similarly made up—a basis steel with 1 wt pct Cr and 0.4 wt pct C and two steels with further additions of 1.2 wt pct A1 or 2.0 wt pct Ti, respectively. The materials were vacuum-melted and cast as 11-lb heats into tapered square molds of about 2 by 2 in. average cross section. The castings were forged and hot-rolled to 11/4 in. rounds. Discs of 4 in. thickness by about 1 in. diam were machined from the rods. Some of these discs were hot-forged and hot-rolled to about 0.020 in. thick, sand-blasted, and then cold-rolled to about 0.003 in. thick. At this point, the surface was cleaned by light etching with HC1, then washed, dried, and vapor-degreased prior to nitriding. 2) Ion-Nitriding Procedure. The type of ion-nitriding equipment used here is similar to that described by Jones and Martin.8 Briefly, a mixture of nitrogen and hydrogen at 5 mm total pressure is placed in a vacuum chamber with a dc potential of 450 to 500 v applied between the work (cathode) and the grounded metal vacuum enclosure (anode). Nitrogen ions are accelerated to the work where a thin layer of Fe4N forms on the surface and thus sets up a nitrogen concentration gradient. This causes nitrogen atoms to diffuse into the surface layers of the alloy forming a finely divided dispersion of alloy nitrides, causing hardening of the surface. In the work to be reported here. the nitriding was carried out at 550° to 600°C to be consistent with commercial nitriding practice. The temperatures cited are those measured by a thermocouple located under a platform on which the work was sitting. Except where otherwise stated, the mixture used in nitriding the binary alloys contained -2.0 pct N, balance hydrogen. The nitrogen concentration in the nitriding gas mixture used for the binary alloys was purposely kept lower than normally used in nitriding steels. 10 to 20 pct, in order to minimize Fe4N formation. In this way only the alloy nitrides would be present as a second phase. However, in the case of steels which would contain a- carbide phase along with as

Jan 1, 1969

By F. D. Hoyt, H. L. Hartman

The development of new processes and methods by The Pennsylvania State University to improve slate quarrying technology has centered in recent years on cutting and sawing stone in the quarry to eliminate a second cutting process in the mill. Two machines exhibit promise for this work: 1) a circular saw mounting diamonds or hard inserts to produce smaller sizes of stone and 2) a chain saw with insert cutting teeth to produce stone in the larger dimensions. Prototype machines have been constructed and tested in several Pennsylvania slate quarries, and one commercial installation has been operated for several months with a circular diamond saw. Other kinds of dimension stones may be cut by these saws. Research at Penn State has begun to study the fundamental cutting action of rotary tools or saws in slate and other dimension stones. A laboratory drill press is being instrumented to permit thrust-torque-rotational speed us penetration rate studies of single tooth cutting surfaces on stone. Machinability studies of slate conducted with tungsten-carbide inserts have been performed. The dimension stone industry generally accepts the rather basic premise that the larger the block removed from the quarry, the more practical and economical the operation. Thus, the concept of cutting to size any dimension stone while it remains in place in the parent bed would receive little consideration from the majority of members of the industry. However, the slate industry, which is usually considered a separate member of the dimension stone family, is pioneering in the development of an in-place sawing method. Before any final decision can be reached concerning a proposed new system, it is essential to take a long, hard look at the present method of operation in order to determine if the new system is indeed an improvement or even desirable. In the following section is a brief description of present quarry practice in the slate quarries of eastern Pennsylvania. PRESENT METHOD OF QUARRYING SLATE In the numerous slate quarries of Lehigh and Northampton Counties of Pennsylvania, the grain and cleavage of the slate are most often at right angles to each other; if a third surface is broken at right angles to these two natural planes of weakness, blocks of more or less rectangular shape can be separated.&apos; In conventional quarrying a large calyx core drill prepares holes of 36-in. diam in which wire-saw standards are positioned. By wire sawing between strategically located core-drill holes, large sinks or benches of virgin slate are opened up. The sides freed by wire sawing will vary from quarry to quarry but generally are rectangular in shape with dimensions averaging 20 ft in length and about 15 ft in depth. Some quarries are fortunate in having a joint or natural parting to work to, which of course diminishes the amount of core drilling and wire sawing required. Once the various benches have been developed either through wire sawing alone or through a combination of wire sawing and natural jointing planes, the block removal proceeds in the following manner. A plug hole is drilled in the block with a compressed-air hammer and a feathering chisel is inserted in the hole to cause a fracture of the rock either with or against the grain as indicated by the positioning of the so-called feathers. This operation is referred to as sculping. After a block has been freed with and against the grain by means of wedging from the cross fracture with long bars or levers, the block is further freed along the cleavage plane by shimming it up with small wooden pieces in an operation known as styling. A large steel loading chain is wrapped around a block thus freed and the chain is attached to the wheel of an overhead cable. The block is then hoisted vertically to the cableway and moved along this cableway laterally to the lip or edge of the quarry. From here it is unloaded onto a rail car or truck for transportation to the processing mill. Except for occasional blasting to free stubborn blocks,

Jan 1, 1961