Search Documents

By H. Wilton Clark

VARYING in thickness and in number from place to place, coal seams in the Canadian Rockies also range in pitch from nearly horizontal to vertical, sometimes with overturns. Over the entire coal-bearing area there are considerable differences of rank in coals of the same geological age, and there are marked differences in ash content and wash-ability characteristics. Correlation of seams at mining operations within a few miles of each other has often proved impossible. These factors influence mining methods, and, of course, production results. The oldest coal formations of western Canada are of Lower Cretaceous age, as the carboniferous sediments are marine and contain no coal. Coal is also present in formations of Upper Cretaceous and Tertiary ages. The rank of coal varies from semi-anthracite in some operations in the Kootenay and Luscar formations of the Lower Cretaceous in the Rockies to lignite in the Tertiary fields of the Saskatchewan prairies. Fig. 1 shows the general extent of the formations. The pitching seams, chiefly Lower Cretaceous, occur in the western belt of the Rocky Mountain foothills and the eastern slopes of the Rockies themselves. (The road to Tent Mt. strip pit, elevation 7000 ft, is shown on p. 832.) Formations extend from the U. S.-Canadian boundary for several bundred miles in Alberta and continue for a similar distance in British Columbia. Present geological estimates show a probable reserve of the order of 25,000 million tons of coal ranging from high volatile bituminous to semi-anthracite, with a large percentage of coking coal, constituting one of the major world reserves of that type. It should be noted that although the quoted estimate probably errs on the conservative side, the question of access to the seams in a mountainous terrain will always be a problem; a wide divergence may exist between actual reserves and the quantities of coal economically recoverable. An excerpt from the Canadian government Report of the Royal Commission on Coal 1946 states that conditions favorable to coal formation were intermittent and these intervals relatively brief in comparison with periods in which no coal was formed. Conditions were favorable to the growth or accumulation of vegetation in one area, while fresh water sediments and marine shales were being deposited in other areas. During periods of emergence the coal deposits were subjected to erosion or were covered by coarse sands and gravels from the mountains, whereas during submergence they were covered by fine clays deposited in embayments of the sea. During some of the periods of coal formation, volcanic activity deposited beds of fine volcanic ash and dust with the coal-forming vegetation. Coal deposits reach their greatest development in the mountains and thin rapidly to the east into the plains area, where they are deeply buried beneath younger sediments. For example, in the Fernie area of southeastern British Columbia there are in places 22 seams having an aggregate thickness of 150 ft in a stratigraphic interval of 3500 ft, whereas at Cole-man in the Alberta Crowsnest area the measures are only 800 ft in thickness and contain a maximum of five seams aggregating about 47 ft of coal. At Belle-vue, 10 miles further east, the measures are reduced to 430 ft with only three seams aggregating about 37 ft of coal. Subsequently the tremendous forces involved in the upthrust of the Rocky Mountains produced great displacement of the coal-bearing formations and at the same time a change in geologically young coals from low to high rank. The floor or footwall of most seams consists of carbonaceous shales, which are almost as adaptable to bending as the coal seams themselves. The seams show very few cleats or cleavage planes and have been so weakened structurally that as mined 50 pct or more will pass through a ¼-in. screen, seldom

Jan 1, 1955

By N. B. Pilling

The deleterious effect on the mechanical properties of copper, re-sulting from heating in contact with reducing gases, is well known, but the mechanism of the action does not appear to have been definitely established. The purpose of the present investigation was not to determine the exact variations in physical quality of commercial copper, with its various impurities, as dependent upon the composition of the gas, temperature of exposure, etc., but rather to study the nature of the action and the conditions under which it occurs. The physical result of the so-called "gassing" of copper has been generally described as the development of "brittleness." There appears to be a striking decrease in tensile strength, associated with a considerable loss of ductility, and a small copper strip or wire affected in this way can be snapped in two when bent. Larger articles may have an outer layer alone affected, which can be detached from the core by hammering or bending. Perhaps the earliest reference to this subject is that of Heynl in 1900, and among the later observers may be mentioned Archbutt,2 Bengough and Hill,3 Johnson,4 Mathewson and Thalheimer,5 and Ruder.6 Bengough and Hill, while working with arsenical copper, were the first to suggest the possibility of the formation of gases within the copper itself, while Ruder endeavored to explain the action by the reduction of the

Jan 1, 1919

By T. Egleston

The direct process for the manufacture of iron which is principally used in the United States, in New York and New Jersey, is called the Jersey forge, the Champlain forge, the Catalan forge, the Bloomary forge or fire, and sometimes a Forge fire. Dr. T. Sterry Hunt, who has discussed the process as applied to the beach sands of Canada as well as to ores, in the Report of the Canadian Geological Survey for 1867-69, has shown that the name of Catalan forge is incorrect, as this process in no way resembles the Catalan, but is really the old German b1oomary modified by long use in this country. Dr. Hunt gives the probable history of the introduction of the process into the United States, and a series of historic citations of great interest relating to it. Notwithstanding the improvements which have been made in the constrnction of the furnace and its greater output, the process to-day, in all its essential features, is carried out as Karsten described it. It should now be known as the American Bloomary. The name of Jersey or Champlain forge or fire is not sufficiently distinctive. The name of Bloomary, by which the process is usually distinguished, is objectionable, not because it is incorrect but because it is indefinite, as the Knobbling fires, which are a very slight modification of the Walloon process, for making blooms either from pig iron or by sinking scrap, are also called Bloomaries, and although Knobbling fires are only used in a few localities where charcoal pig is made, and special grades of charcoal-refined blooms are required, one does not, without an explanation, know whether the blooms are being manufactured from ore or pig. The name Forge fire is equally indefinite, as it might just as well apply to any of the five direct methods of making blooms which have been in use in Europe, but which have now mostly gone out of date. The name of American Bloomary, however, is the one which most completely describes it, and is the one least open to objection. The names of' German, Jersey, and Champlain bloomary are too local, and these adjectives are thought unnecessary by those who use the process, and we shall not therefore describe it under any of these names, but as the American Bloomary process.

Jan 1, 1880

By G. W. Neighbor, M. S. Abrahams

The actice slip plane in InSb is found to be of the {111} type by using the method of two-tmce anulysis. Measurements of the rotation of the tensile axis with increasing plastic shear strain indicate that the tnacroscopic slip direction is a <110>. Recrystal-lization is first observed at a sheav strain of about 70 pct for a crystal deformed at a temperatzcre of 473° C and at a shear strain rate of 2.90 times 10- %ecc-I; the dislocation density corresponding to this value of the strain is 1 x 108 em-&apos;. At a shear strain of about 170 pct, the recrystallization process is complete. This appears to be the fimt time re-crystallization has heen observed in a semiconductor. V HE operation of the {Hi} glide plane in Ge was first noted by Gallagher.&apos; This finding was confirmed by Treuting who also extended the result to Si. Using X-ray techniques, Treuting3 demonstrated that the macroscopic slip direction in Ge was of the <110> type. The choice of the (111) <110> slip system in Ge is exected since in the diamond-type structure the {Ill7 plane is the plane of highest density and the <110> direction is the direction of closest packing.4 There is little reason to expect that the glide elements of InSb are different from those of Ge, since the zinc-blende structure characteristic of InSb is quite similar to the structure of Ge. With regard to InSb, Allen5 has indicated that the glide plane is the {111} type. There appears to be no quantitative determination of the glide direction, however. The present work was undertaken to establish both the glide plane and glide direction in InSb and also to see if recrystallization occurs at large shear strains. EXPERIMENTAL PROCEDURE Mechanical Deformation. The single crystals of InSb used in this investigation were deformed in uni-axial tension. The tensile axis of the specimens was [145] and the periphery was bounded by (111) and (321) planes as shown in Fig. 1. The metallographi-cally polished specimens were deformed in a dynamic atmosphere of He, using an Instron machine. The tensile tests were performed at temperatures in the range of 300°C to the melting point (525OC) and at shear strain-rates varying between 1.94 X 104 sec-&apos; to 1.94 x 103 sec-&apos;. Additional details concerning the preparation and deformation of the specimens have been presented previously.&apos; Analysis of the Glide Elements. The traces of the active slip plane in both (111) and (321) planes were analyzed according to the usual method of two-trace analysis." The macroscopic slip direction was determined by measuring the rotation of the tensile axis as a function of plastic strain,8 These measurements were made from Laue back-reflection X-ray photographs. The X-ray beam was perpendicular to the (111) plane. A given crystal was used for only one measurement of the rotation of the tensile axis after it had been strained to a predetermined value. Therefore, care was taken at all times to insure that the X-ray beam was parallel to the [Ill ] direction of all the samples. RESULTS AND DISCUSSION Glide Plane. After 3.4 pct plastic shear-strain, at a temperature of 369°C and a shear strain-rate of 1.94 x 104 sec-&apos;, the slip traces on the (111) and (3.21) planes appear as in Figs. 2(a) and 2(b), respectively. The results of an analysis of these glide markings demonstrate that the slip plane is (111). The operation of this plane is expected on the basis of the orientation of the specimen, since glide on this plane and in the [I011 direction will result in

Jan 1, 1962

By W. M. Phillips

Processing kaolin clays from the sedimentary deposits of Georgia and South Carolina is described in this article. While the major processing steps are touched on briefly, emphasis is given to the dewater-ing of the clay-water slurries (slips) formed in the processing of kaolin clays. The dewatering steps discussed include gravity settling, centrifugal dewatering, vacuum filtration and thermal drying. Particular attention is given to vacuum filtration and the variables affecting filtration of these kaolin clays. Kaolin consists essentially of the mineral kaolinite, which is a hydrated aluminum silicate (Al2O3 . 2SiO,). Commercial deposits of kaolin occur in several areas of the U. S., but approximately 90% of the kaolin produced in this country comes from Georgia and South Carolina. These deposits are of sedimentary nature and occur in a geological fall line in the Tuscaloosa formation at elevations between 300 and 450 ft above sea level. Over two million tons of kaolin clays are used by industry in the U. S. each year. A big percentage of this tonnage is used in the paper industry for coatings in making glossy and high quality grades of printing papers. In addition, large tonnages are used as pigments; as fillers for rubber, plastic and fertilizers; and in ceramics. Properties of kaolin that make it widely used in the above applications are its particle size fineness, natural whiteness, chemical stability and non-abrasiveness. In addition to these desirable properties, it is relatively inexpensive. The finer coating grades of clays range in price from $15 to $28 per ton while the coarser filler grades sell within a range of $7 to $13.50 per ton. Pure kaolin particles are small hexagonal flat platelets. Above the 2-p size, the particles usually consist of stacks of plates, while below the 2-p particle size they occur as individual flat, hexagonal plates. Since these individual platelet particles provide the most desirable coating and flow characteristics, major importance is given to particle size fractions of 2 p and smaller. Generally, coating grade clays are those with all particles smaller than 15 p and at least 70% of the particles less than 2p. These coating grades also have 50% or more of the particles smaller than 1 µ in size. The extremely fine grades of coating clay currently being produced approach the range of 100% smaller than 2p. The filler grades of kaolin have 100% of the particles passing 325 mesh but have less than 70% of their particles below the 2-p range. Fig. 1 is a schematic representation of the major processing steps involved in preparing kaolin clays for marketing. MINING All kaolin mining is open pit. The ratio of overburden to clay will average 3:1, but this ratio can, of course, be much higher depending upon the grade of the clay and the size of the deposit. Most of the commercially mineable deposits occur from 20 to 120 ft below the ground surface. Both draglines and pans are used in removing the overburden and mining the clay deposit itself. After mining, the most common method of transporting the clay to the processing plant is by blunging or re pulp-

Jan 1, 1963

By Thomas E. Garnar

Zirconium and hafnium are curious elements because they are almost always found together in nature. Zirconium was discovered by Klaproth in 1789 and isolated 35 years later by Berzelius. Because hafnium&apos;s chemical properties are so close to those of zirconium, it was not discovered until 1923 when Coster and Von-Heresey detected it using x-ray spectrographic analysis. These elements occur most commonly in nature as the mineral zircon (ZrSiO4) and less commonly as the oxide baddeleyite (ZrO2). They also are found as a variety of other silicates. Zircon was identified as a component in alluvial and beach sands in 1895, but it was not produced in any quantity until 20 years later. Zircon is always a coproduct from TiO2 mining and processing. During World War I it was produced as a coproduct of beach sand mining for titanium minerals just south of Jacksonville Beach, FL, and was patented as a refractory. It was not until the 1930s when Zircon Rutile, Ltd. began mining at Byron Bay on the east coast of Australia that zircon was first used as a foundry sand. Later in the 1940s, NL Industries, Humphreys Gold Corp., and E. I. du Pont de Nemours & Co., Inc. began production of zircon sands from fossil beaches in northeast and northcentral Florida. Baddeleyite first became available as a commercial product in 1916, but never in the quantity of zircon. Zircon holds a unique position as an industrial mineral because it is used for both its physical and chemical properties as well as an ore of zirconium and hafnium metals. Australia is the major zircon producer followed by South Africa and the US. Zircon is also produced in India, Sierra Leone, Sri Lanka, Malaysia, China, Thailand, and Brazil. Undeveloped heavy mineral beach sand reserves containing zircon are known to occur in Egypt, Malawi, Senegal, and Tanzania. Locations are shown in Fig. 1. Mineralogy Zirconium and hafnium are always present together in naturally occurring compounds. Most commonly they form as the silicate sometimes containing iron, calcium, sodium, manganese, and other elements. Less commonly they are found as oxides in combination with titanium, thorium, calcium, and iron. Zircon is the most common form. It is extremely resistant to weathering, therefore, often it is present in ancient beach sands and placer deposits. Although resistant to alteration from external sources, it is vulnerable to internal alteration as the result of thorium and uranium substituting for zirconium either in the zircon lattice or in solid solution. Alteration to the metamict state takes place as radioactive emanations from these elements disorder the crystal lattice, accompanied by hydration, reduction in specific gravity, and changes in color. The mineralogy of zircon and baddeleyite and variation of physical and chemical properties are shown in Table 1. The effects of zircon&apos;s internal alteration and darkened color can be corrected by heating to 1000°C for 30 min or so. A certain time-temperature relationship makes it possible for decolorization and reordering of the crystal lattice to take place when heating at higher temperatures for shorter periods or at lower temperatures for longer periods. After heating, x-ray diffraction patterns are sharper, the grains may be harder, and except for particles of malacon, the grains will be white or colorless in the absence of grain surface coatings. The color change is only temporary and the particles slowly darken with time. Zircon fluoresces light yellow in shortwave ultraviolet light. If exposed to ultraviolet light for extended periods of time, white (calcined) zircon turns purple. With time the induced color begins to fade and eventually disappears (e.g., calcined Florida zircon exposed to ultraviolet light for 24 hr still retains faint, but discernible, purple color after six months).

Jan 1, 1983

By D. J. Carney, E. C. Rudolphy

IT has been demonstrated that inclusion size, distribution, and composition affect the machin-ability of resulphurized steels. Merchant and Zlatinl concluded that large sulphide inclusions aided machining by forming a (lubricating) coating on the tool face. Boulger et al.² and Van Vlack³ noted that the size, distribution, and composition of the inclusions in the steel affected the machinability. Steel specimens containing large globular sulphide inclusions usually exhibited excellent cutting properties, while machinability was adversely affected by the presence of numbers of oxide-type inclusions. Consequently a thorough knowledge of all the factors which affect the inclusions in the final product is desirable. Since almost all the inclusions have their origin in liquid steel, it was necessary to begin a study of inclusions in free-machining steels by studying the inclusions and chemical segregation in the as-cast ingot. Very little information is available on the size, distribution, shape, and composition of inclusions in large, capped, free-machining steel ingots, particularly the B1113 grade. Gregory and Whiteley4 made a general study of the inclusions in a small, high sulphur, free-machining steel ingot. Also, numerous authors have described the solidification and segregation characteristics of the four basic types of steel ingots, namely, rimmed, capped,7 semikilled,7,8 and killed7,9,10 ingots. Most of these studies were made with plain carbon or low alloy, low sulphur steel. It was desirable to study not only the ingot but also the change in size, shape, and number of inclusions on rolling an ingot to a bloom and thence to a billet. This procedure was followed and it is hoped that this study may serve the dual purpose of adding to the general knowledge of ingot solidification as well as contributing to the knowledge of the size, shape, distribution, and composition of inclusions from the ingot to the billet in a high sulphur, free-machining steel. Procedure A 12.000-lb 23x35x75 in. slab ingot of the B1113 grade was cast, sectioned, and studied both macro-scopically and microscopically. An adjacent ingot from the same heat and of the same size was rolled to a 77/8x77/8 in. bloom and thence to a 21/2x21/2 in. billet. These various bloom and billet sections were also sectioned and studied macroscopically and microscopically. Sectioning the Ingot: The ingot herein described was obtained from the United States Steel Corp.&apos;s South Works Bessemer Blow No. 0193, a B1113 mechanically capped heat. The 23x35 in. ingot (No. 2) was teemed according to normal procedures and after stripping and transportation to the rolling mill was not placed in the soaking pit but allowed to air cool in an upright position. When completely solidified, the ingot was cut into sections by means of a powder scarfing torch and further sectioned by saw cutting as indicated in Fig. 1. Cut No. 2 (1x10x12 in.) from sections A through H was cleaned thoroughly, macroetched in a solution of 50-50 water and hot muriatic acid and used to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 23-in. ingot dimension. Cuts No. 5 and 3 (lx81/2xl0 in. each) from sections A through H were treated in a similar manner to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 35-in. ingot dimension. The composite macrograph of these horizontal ingot sections, which shows a vertical section of the ingot from top to bottom, is shown in Fig. 2. It should be noted that sections No. 2 are normal to sections 5 and 3 in the composite. Drillings for chemical analyses were obtained from selected positions within the above-mentioned ingot sections as noted in Fig. 3. The oxygen content was determined by the vacuum-fusion method. Samples for microscopic examination were cut from

Jan 1, 1954

By M. C. Udy, C. H. Lorig

THROUGH the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the general effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. LITERATURE Two general factors should he considered in a study of reduction of iron oxide: (1) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe3O4-FeO-H2-H2O, Fe304-FeO-CO-CO2, FeO-Fe-H2-H2O, FeO-Fe-CO-CO2 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnas1 published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at one temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1942

By J. M. W. Mackenzie, C. J. Wood

In attempting to describe the size classification performance of a hydrocyclone, most workers have elected to use either an equilibrium orbit theory or an non-equilibrium orbit theory. The equilibrium orbit theory has been used by the majority of workers including Lilge,&apos; Bradley; and Yoshioka and Hotta. In applying this theory, it is argued that particles in the body of a hydrocyclone attain an equilibrium radial position where the drag force on the particle resulting from the inward radial fluid velocity is balanced by the outward centrifugal force caused by the tangential component of fluid flow. When considered over the full height of the hydrocy-clone, attainment of this radial equilibrium orbit results in the particle following a conical equilibrium envelope. It is then argued that if this envelope lies outside the envelope of "zero vertical velocity," the particle will report to the underflow, while if the equilibrium envelope lies inside the envelope of "zero vertical velocity," the particle will report to the overflow or vortex finder product. The d50-sized particle which reports in equal quantities to the underflow and overflow is assumed to correspond to particles whose equilibrium envelope is coincident with the envelope of "zero vertical velocity." In considering the equilibrium orbit theory, it is apparent that the horizontal position of the particles in the feed inlet pipe should have no effect on their ultimate destination on the hydrocyclone. Each particle should attain an equilibrium position which depends on the density, size, and shape of the particle; the density and viscosity of the fluid; and the flow patterns within the hydrocy-clone. The nonequilibrium orbit or unsteady state theory has been largely developed by Rietema4 and Mizrahi.6 Mizrahi has listed four main objections to the equilibrium orbit theory. These objections center on the short residence time in the hydrocyclone, the fact that the experimental classification curve is much less sharp than is theoretically predicted, and the absence of negative efficiency conditions in hydro cyclones operating on a feed material which is much finer in size than d50. Proponents of the nonequilibrium orbit theory argue that for a particle to discharge with the underflow it must have sufficient outward radial velocity to reach the downward-flowing region close to the hydrocyclone wall in which the flow lines are parallel to the wall and the ratio of vertical to radial velocity is constant. It is then postulated that a d50 particle entering the cyclone at the center of the feed inlet will just reach this downward-flowing region as it reaches the apex. Thus for uniform distribution of particles across the feed inlet, half the d50 particles—that is, those injected in the half of the inlet area nearest the cyclone wall —will report to the underflow while those injected in the other half will not reach the downward-flowing region and will be carried inward to the center of the cyclone and thus report in the overflow. The exact thickness of the down-ward-flowing region of fluid adjacent to the outer wall of the hydrocyclone is uncertain but Mizrahi considers it to be equal to the apex radius minus the air core radius. Particles larger than d50 have a greater outward centrifugal force acting on them than the d50 particles and may reach the wall even if injected at a distance from the wall greater than Di/2 (Di is inlet diameter). Conversely, particles smaller than d50 may not reach the wall even if injected at a distance less than Di/2 from the cyclone wall. Since the equations put forward by the proponents of both theories yield approximately the same values of d50, it is not possible to decide between these theories by measurement of d50. It should be possible however to examine the theories by injecting a small stream of solids into the feed inlet of a hydrocyclone running on clear water. If the efficiency or classification curve is measured for various horizontal injection positions, then the curves should be coincident if the equilibrium orbit theory holds. If, however, the unsteady state theory describes the cyclone operation, then the classification curves should show finer d50 sizes for particles injected close to the cyclone wall. Experimental A 6-in.-diam hydrocyclone with geometry as in Figs. 1 and 2 was used. Quartz particles were injected as a 50% by wt pulp via an 1/8-in. steel probe. For each in-

Jan 1, 1971

By E. S. Machlin, Morris Cohen

GRENINGER and Troiano&apos; were the first to establish the fact that the habit planes of mar-tensitic products are usually planes of high indices. In steels containing 0.55 to 1.4 pct C, the habit plane indices are {225}A.* In steels with more than 1.5 pct C and in Fe-Ni alloys, the indices are {259In. The presence of both habits in certain alloy steels has been reported recently." Several investigators"-" have subsequently attempted to provide an understanding of these complex habit relations. Bowles&apos;6 work is the most recent and the most successful. Like Greninger and Troiano, Bowles concluded that the transformation occurs in two steps, the first, a strain (or displacement) that is homogeneous throughout the volume of the martensitic plate, while the second is a strain that is homogeneous only within relatively small portions of the martensitic plate. The first strain yields the measured tilt of the specimen surface, but does not produce the final martensitic structure. This and the correct lattice orientations are achieved by the second strain. Bowles also reasoned that each strain could be described by the motion of a plane of no rotation and no distortion (hereinafter called the invariant plane) in a direction not necessarily contained in the plane.** In applying these considerations to steels with {225}a habits, Bowles found that the habit plane coincided with the invariant plane of the first strain, a result which signified that the atoms move along certain paths during the transformation. Whether this correlation results from the existence of some sort of a plate nucleus6 lying along the invariant plane of the first strain, or whether the invariant plane primarily defines the preferred directions of propagation of the first strain, will be discussed in a later section. There are two obstacles to the general acceptance of Bowles&apos; treatment: 1—it has not been shown that elements of his double-strain analysis are unique, and 2—it is not known whether his treatment applies to transformations yielding the {2591A habit. Unless these two questions are resolved, the correlation between the habit and invariant planes in the {225}A systems might be regarded as coincidental. Experimental Procedure Using a 70 pct Fe-30 pct Ni alloy as an example of a {2591A habit system, preliminary attempts were made to obtain a double-strain solution based on a Nishiyamax** set of orientation relations and on a Greninger-Troianot set, adopting the stereographic technique described by Bowles" who used the Kurd-jumow-Sachstt set in connection with the {225}A habit. These attempts were unsuccessful because the method is essentially one of trial and error and requires either exceedingly good luck or a prior knowledge of the results being sought. Consequently it was decided to measure independently the strain associated with the formation of a martensitic plate as well as the habit-plane indices of the particular plate. By means of matrix algebra, the measured strain was applied to the austenite lattice, whose orientation with respect to the strain was determined, in order to ascertain whether the resultant structure would have the lattice of martensite. This was not found to be the case, and hence it was assumed that the measured strain was the first of two Bowles-type strains, characterized by the motion of an invariant plane. A solution of this displacement was obtained in terms of the invariant-plane indices and the direction of motion of the atoms. Then the second strain

Jan 1, 1952

By M. G. Corson

INFORMATION regarding the use of manganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties .and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists.1 PROPERTIES OF MANGANESE Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850° C. and the other below 650° C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the silicides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available.

Jan 1, 1927

By John D. Verhoeven

A technique has been developed for carrying out normal freezing experiments with a current density of 2000 amp per sq cut passing through the solid-liquid interface. The equation relating the effective distribution coefficient to the equilibrium distribution coefficient in electric field-aided solidification, originally developed by Huckc et al.,1 has been modified for the case of concentrated solutions. Preliminary experiments on the Sn-Bi system give qualitative agreement with the equation. The data are analyzed by a slightly novel use of the normal freeze equation which allows one to determine the effective distribution coefficient more easily. Very extensive mixing in the liquid was found at these high current densities and it is postulated that the mixing results from a vertical component of the magnetic Lorentz force generated by the electric current. In the search for techniques of obtaining ultrahigh-purity metals the inefficient but very effective technique of electrotransport has received little attention. Electrotransport is most effective in the liquid state and a natural application, therefore, is to apply an electric field across the liquid zone of a zone-melting experiment. The present investigation was undertaken to study the effect of an electric field upon solidification of metals, so that the usefulness of electrotransport in such solidification experiments as zone melting could be determined. In zone-melting and normal-freezing experiments it is difficult to achieve complete mixing in the liquid in the immediate vicinity of the solidifying interface. Consequently a solute build-up will occur at the interface in the portion of the liquid where complete mixing does not occur (an equilibrium distribution coefficient, ko, less than one, and unidirectional atom motion will be implied throughout). This local solute build-up produces a corresponding rise in the solute concentration in the solid so that the ratio of the solute concentration between the solid and the bulk liquid is larger than the equilibrium distribution coefficient. This ratio is defined as the effective distribution coefficient, k,. The differential equation describing the solidification process may be derived by applying the continuity equation to an expression for the net solute flux at the interface. The solution to this differential equation then allows one to determine the solute distribution in the liquid and the relationship between k0 and ke. One of the most useful solutions to this equation was first derived by Burton, Prim, and Slichter,&apos; in which they assumed that a) the equilibrium distribution of solute was maintained on the plane of the interface, 11) the solute build-up ahead of the interface in the liquid disappeared at a distance 6 from the interface, and c) the solute distribution in the liquid was invariant with time. The following well-known relation between ko and ke was then obtained, where R is the rate of solidification and D the diffusion coefficient of the solute in the liquid. This equation appears to correlate the data from a number of different types of solidification experiments very well. Application of an electric field across the solid-liquid interface can produce an additional flow of solute atoms as a result of the electrotransport. When the polarity of the field is such as to direct the electrotransport flux away from the interface the solute build-up may be diminished, even to the point of producing a solute depletion and a consequent ke smaller than ko. The quantitative description of this process and the resulting form of Eq. [I] was first given by Hucke et al.1* and then inde- where E is the electric-field intensity and U is the differential mobility, i.e., the velocity of the solute atoms with respect to the solvent atoms per unit electric field. Both authors follow the method of Burton, Prim, and Slichter in their derivation, the only difference being the additional electrotransport term in the flux equation. It has been pointed out1,3 that Eq. [2] predicts the possibility of a noticeable increase in the purification of materials by solidification in an electric field. The validity of Eq. 121 has not been checked experimentally and it is possible that other factors&apos; arising from the presence of an electric field across

Jan 1, 1965

By Paul A. Farrar, Harold Margolin

The system Ti-Cr has been re investigated From 40 to 100 pct Cr. The high-temperature modification of TiCr, was found to exist in the temperature range from 1365 where it terminates in the eutectoid reaction TiCr,(TI)* — HE chromium-rich region of the Ti-Cr system was investigated by Vogel and Wenderott,&apos; Mc Quillan,&apos; Van Thyne et dl.,&apos; and Cuff Duwez and Taylor determined the crystal structure of the low-temeperature modification of TiCr, to be fcc a = 6.943A and Levinger&apos; discovered the existence of a second (high-temperature) modification of TiCr, and determited its crystal structure to be hexagonal a = 4.932A, c/a = 1.617i. No information was obtained as to the temperature range over which each modification of TiCr? existed; therefore the present investigation was initiated. I) Experimental Techniques Alloys employed for the delination of this system were prepared from iodide titanium and high-purity chromium. The purity of these materials is as follows: Iodide titanium: purity 99.99 pct; major impurities—carbon 0.0001 pct; oxygen 0 to 0.002 pct; nitrogen 0 to 0.002 pct; silicon 0 to 0.005 pct; manganese 0.001 pct; copper 0.001 pct (Foote Mineral Co., Lot 609-29). Chromium #1: metallic purity 99.997 min.; interstitial content—oxygen 0.27 to 0.46 pct; hydrogen 0.028 to 0.038 pct; nitrogen 0.0002 pct (Ave-quipo Inc.). Chromium #2: purity 99.9 pct; major impurities—carbon 0.01 pct; oxygen 0.013 pct; nitrogen 0.02 pct; silicon 0.01 pct; sulfur 0.03 pct; iron 0.01 pct (Fulmer Research Institute Ltd.). A total of sixteen alloys of thirteen different compositions was prepared in the range from 40 to 95&apos; *All percentages are given in weight percent. pct Cr. The compositions of the alloys prepared were as follows: Ti-40, 45, 50, 60, 62, 64, 66, 68, 70, 80, 85, 90, and 95 pct Cr. Two buttons were prepared of the 66, 90, and 95 pct Cr alloys. The 40 pct Cr and one of the 66 pct Cr alloys were prepared from the chromium # 2. All the other alloys were prepared from chromium #1. The alloys were arc-melted as 25-g buttons in a copper-hearth glass-walled furnace7 under an inert atmosphere of high-purity helium. The alloys were sintered at 250 amp and melted twice at 350 amp for 30 sec with the buttons being turned over between melts. Weight losses during melting were determined and in the range 45 to 68 pct Cr they were found, in all cases, to be less than 1.25 pct of the total alloy weight. A number of the high-chromium alloys shattered during cooling from either the first or second melt, which made the weight loss considerably larger than usual. The 70 and 80 pct alloys lost approximately 5.7 pct of their total weight, the 85 pct alloys 1.5 pct, the 90 pct alloy 2 pct, and the 95 pct alloy 3 pct. However, it is felt that the actual composition of the alloys in this region is probably within approximately 1 pct of the intended composition, as a large portion of the material lost was that due to shattering after melting. Nominal compositions were therefore used in plotting data and referring to the alloys. The alloys were cut into specimens, wrapped in molybdenum sheet, and encapsuled in argon-filled quartz or Vycor tubes for heat treatment. The heat-treatment times and temperatures are given in Table I. The specimens were quenched in iced brine (I.B.Q.) following heat treatment. The standard techniques of grinding, polishing., and etching were used in preparing the specimens for metallo-graphic examination. For alloys below 68 pct Cr

Jan 1, 1963

By B. G. Matson, M. A. Whitfield, G. R. Dysart

This paper describes the development of u computer program to calculate changes that occur in the length of tubular goods due to temperature and pressure changes during stimulation operations. Due to the numerous variables involved and the uncertainty of all static and dynamic conditions that could exist, it becomes a staggering task for individuals charged with completions to perform the necessary mathematical calculations. The computer program permits advance calculations for several sets of conditions. INTRODUCTION In the Delaware basin of West Texas alone, 50 wells were contracted or drilled to 15,000 ft or deeper in 1965. Deep well activity is continuing in this and other areas on an expanding scale. Many of these deep wells require extensive stimulation for successful commercial production, and during these operations, pressures and temperatures are encountered that have a pronounced effect on the length of tubular goods. This length change during a large-volume, high-pressure stimulation treatment utilizing fluids considerably cooler than bottom-hole temperature can be of such a magnitude that permanent damage to casing and tubing will result unless mechanical design, pressures and fluid temperatures are evaluated and controlled. These pressure and temperature effects can be calculated. However, the process lends itself well to computer solutions because of the mathematical nature of the problem and the calculating hours involved in arriving at an answer. The engineering-hour demand becomes more severe as tapered strings are involved. On initial treatments on a given well, surface pressure and injection rate conditions are unknown, and offset well conditions have not proven to be a reliable method for making predictions. For these reasons, it has become rather standard procedure for operators to compensate for these uncertainties by placing unnecessary pressure and fluid temperature restrictions on stimulation design. On a number of occasions treating fluids have been preheated to as much as 160F as a means of compensating for thermal contmction resulting from pumping cool fluids. The maintenance of packer seals has been treated by Lubinski, Althouse and Logan&apos;,&apos; and the problem of therma1 effects on pipe has been explored by Ramey." These works were expanded and the results made applicable to everyday oilfield terminology before submitting them to computer programming. The pressure and temperature effects on tubing movement previously mentioned occur simultaneously as fluid moves through the pipe. The pressure changes, for purposes of explanation, are categorized here as to the various effects these pressures have on a tubing string. These divisions are (1) the piston-like results of forces acting on horizontal surfaces exposed to pressure, (2) swelling or ballooning of the tubing along its entire length due to the forces of pressure acting against the tubing walls, (3) the elongation of tubing due to frictional drag and (4) corkscrewing of the pipe due to internal pressure. Thermal changes are also of great importance, as their results may be more significant than any of the pressure effects. Steel is an excellent conductor of heat and the earth is a relatively poor conductor. It has been calculated that pipe temperatures at depths of more than 20,000 ft approach within as little as 25" the temperfature of the surface fluid after pumping for 2 hours, or a drop in temperature in some treatments of more than 220F. The equations presented in this paper were developed for computer programming and simplicity of input information; therefore, numerical constants such as Young&apos;s modulus for steel (28 X 10\ si), the coefficient of thermal expansion of steel (6.9 X 10."IF) and Poisson&apos;s ratio for steel (0.3) are included with unit conversion factors. The moment of inertia of tubing cross-sectional area with respect to its diameter was changed to a constant times (D&apos; — d&apos;) where D is outer diameter and d is inner diameter. Units in the equations are length in feet, diameter in inches, density in pounds per gallon, pressure in psi, rate in barrels per minute and time in hours. PISTON-LIKE REACTIONS A change in tubing internal dimensions and the exposure of other horizontal surfaces to different pressures on the inside and outside of the tubing result in a reaction much like a piston under pressure. Such is the case when the internal diameter changes in a combination string of pipe, when seals of a slick joint assembly are subject to pressure and in the end effects of a tubing string. The change in tubing length due to the piston effects of a slick joint packer is affected by the various diameters involved, the tubing pressure Ap,, the casing pressure ,Ap,, length of pipe L, densities of fluid in the tubing before and during pump-

By B. H. Cody

THE Morenci concentrator of the Phelps Dodge Corporation is a part of the project that was completed after five years had been spent in development of the open-pit mine, equipment and process testing in the former No. 6 concentrator, and construction of the reduction works. The reduction works, of which the concentrator is a part, is about a mile and a quarter southeast of Morenci, on the highway that leads up Morenci Canyon. The concentrator has a nominal capacity for the treatment of 45,000 tons of ore daily. The original plant, which has a rated capacity of 25,000 tons of ore daily and is now in its fifth year of operation, began production on Jan. 30, 1942. The addition, to increase the capacity 8o pct, began operation on Dec. 1, 1943. The equipment of the original plant has been described in MINING AND METALLURGY (May 1942). No changes in equipment were recommended for installation in the concentrator extension and only one major change, forced by a shortage of maintenance labor, has since been made. Metallurgical treatment has been altered in some ways as experiments progressed and as labor and economic conditions dictated. No complete description of the operation of the concentrator has been published, so this paper will record such operating and equipment changes as have been necessary, the operating methods that have been developed and the metallurgical results that have been obtained. Descriptions are given in the order of the processes with a flowsheet and an equipment list of each process for convenient reference. The questions asked by engineer visitors have guided the detail in which operation and maintenance are described. During the period Jan. 30, 1942 to Sept. 1, 1946, ore milled has totaled 43,595,253 dry tons, from which 1,643,885 tons of concentrate have been made, containing an indicated production of 783,164,809 lb of copper. The principal results obtained in operation of the concentrator during the years 1942 to 1945, inclusive, and to Sept. 1, 1946 are shown in Table 1. A graphic general flowsheet of the plant is given in Fig I. ORE The Morenci ore that is now being treated is a medium-hard monzonite porphyry in which the principal sulphide minerals are chalcocite and pyrite. A minor amount of covellite is present. Chalcopyrite and bornite have been observed under the microscope. The chalcocite occurs mainly as a coating on pyrite. Some of the coatings are so thick that the pyrite presents the appearance of being an inclusion in chalcocite. Some are less than one micron thick and are barely visible at 500 diameters magnification of a polished cross section. Some chalcocite is present as a dissemination in the gangue. Various oxidized copper minerals are present as a result of oxidation in place but they represent a minor proportion of the copper minerals of the ore body. Oxidation

Jan 1, 1947

By G. W. Gross

A commercial deposit of white kaolinite clay contained in the sandy overburden of the Cambrian Gatesburg formation in Central Pennsylvania was successfully mapped by combined SP and resistivity methods and results were checked by drilling. Resistivity minima in the range between roughly 2000 and 3500 ohm-meters coupled with second-order SP maxima of 50-60 mV contrast were found to characterize commercial white kaolinite clay beneath not more than 30-40 ft. of sandy overburden in the area stdied. This investigation supports the hypothesis, established previously, that certain SP phenomena may reasonably be ascribed to diffusion and membrane potentials produced by interaction of clay lenses, sandy matrix, and ground waters. The success of this test proves that this prospecting technique can assist in locating clay deposits in sandy overburden derived from the weathering of sandstones and carbonate rocks such as the Cambrian formations of Central Pennsylvania. In a recent paper, Gross and Moore (1959) described broad self-potential minima above the outcrops of the Cambrian Gatesburg formation. These "first-order" SP anomalies, of 220-350 mV contrast (Figure 7), are related to the peculiar sandy residual soil covering the Gatesburg formation. Small positive ("second-order") peaks of 50-60 mV contrast are superposed on the bottom or flanks of the first-order troughs. They appear to be related to lenses and layers of kaolinite clays within the sandy Gatesburg overburden. Both first-order and second-order anomalies show a characteristic inverse relationship with apparent resistivity profiles in most cases. An explanation in terns of liquid-junction and shale potentials was advanced. According to this working hypothesis, shale potentials are generated: 1) at the contact of the sandy Gatesburg overburden with the more argillaceous soils of surrounding formations; 2) at the boundary of clay lenses contained in the sandy matrix of that overburden. Concentration gradients between interstitial infiltration waters and perched water tables within the Gatesburg overburden are believed to give rise to the liquid-junction potentials. In order to test this hypothesis further, a detailed study was carried out of a second-order positive anomaly on the property of the Woodbury Clay Co. at Mines (Blair County, Pa., Hollidaysburg folio of the U.S. Geological Survey). A second aim was to establish if combined SP and resistivity surveys are suitable as a practical method for delimiting favorable areas in which commercial kaolinite clay de~osits may be found by drilling. Drilling control was provided by the Woodbury Clay Co. PROCEDURES Instrumentation used for SP measurements was the same as described in the paper mentioned. For resistivity surveys, a direct-current voltmeter-ammeter device built by Georator Gorp. of Manassas (Va.) was used in combination with non-polarizing electrodes from the same manufacturer. Power was supplied by one to six 45-volt, heavy-duty B-batteries

Jan 1, 1961

By H. S. Bell

It seems unnecessary to dwell upon the advantages of the modern pipe still as compared with the older type of distillation equipment used by oil refiners. The relatively low installation cost, coupled with remark-able operating efficiencies of pipe stills, precludes the consideration of other types except in rare instances where some peculiarity of product or plant may have an influence. The question of the actual heat required to distil petroleum is quite involved. We have extensive data on the latent heats of the various hydrocarbons under different conditions of pressure. We also have information regarding the specific heats of various oils and the effect of temperature thereon. Because of the complexity of petroleum and of each fraction, it seems impossible to analyze theoretically the partisl-pressure effect of the great number of hydrocarbons upon one another during distillation. If a distillation curve and percentage analysis of any crude or product are available, it is possible to construct a curve with ordinates representing per cent. distilled and B. t. u. per pound or per gallon, or other desired unit. To do so the crude is split into fractions, of 5 or 10 per cent. The boiling point and gravity of each fraction being determined, it is possible to evaluate the heat required. As each fraction is removed, the residue must be raised to a higher temperature and latent heat supplied for the successive fraction. As the calculations progress, the latent heats decrease while the specific heats increase. Such a curve is illustrated by Fig. 1 for a typical 39.9° Be. North Texas crude. The chart is illustrative of batch distillation. Theoretically, if the oil were heated by a single flash in a pipe still, the partial-pressure effect of the light products would result in the removal of the same amount of vapors at a lower temperature. Practically, we find that because of the necessarily extensive fractionating equipment required when separating many products all in vapor phase, the oil has to enter the separator at temperatures corresponding to or even above those required in the batch still. Furthermore, in single-flash distillation the vapors evolved in the heater must be superheated to the outlet temperature. Very little is

Jan 1, 1928

By Aloys H. Wohlrab

THE conditions that govern the selection of a suitable type of detachable bit for the small, isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may not be able to adopt the practice of large mines because of necessary capital expenditures for equipment for detachable-bit sharpening and shanking. The perfect detachable bit, suitable for all conditions, has not yet been developed. CONVENTIONAL DRILL BIT IN USE That drilling speed increases as the bit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests carried out by Holman Brothers Limited1 with 7/8 -in. steel show that when bit sizes are reduced from I ½ in., I 3/8 in., and I 3/16 in., to I 3/8 in., I ¼ in., and I 1/8 in., respectively, the volume of the hole is 15 per cent less and the drilling speed 49 per cent higher. Recent tests by the United States Bureau of Mines2,3 in hard, uniform basalt showed that a reduction in average gauge from 2.077 to I.826 in., a difference of 0. 2,5I in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and I4° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr characteristics) by some mines.4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and 14° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as can be forged economically. Shop practices and costs have been discussed in earlier papers.5.6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert.7 REQUIREMENTS FOR DETACHABLE BIT FOR HOLLINGER Under these circumstances, it was apparent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in

Jan 1, 1942

By S. Usui, I. Iwasaki

The adsorption mechanism of dodecylammonium acetate (DAA) on mercury in potassium fluoride solutions at natural, near neutral pH was investigated. Difler-ential capacity combined with electrocapillary measurements on a dropping mercury electrode were found to provide a sensitive and reliable approach. A shift in the electro capillary maximum (or the point-of-zero-charge) towards positive polarization of the surface due to the adsorption of amine indicated a specific affinity of dodecylammonium ion for mercury surfaces. The amine was shown to adsorb competitively with potassium ion on mercury. Through correlation of the adsorption density of the amine, calculated from the thermodynamic analyses of the electrocapillary curves, and of the diflerential capacity curves, the adsorbed state and the orientation of the amine at the interface were considered. The similarities and the differences in the adsorption behavior of the amine on mercury and on such ionic solids as quartz, silver sulfide, and silver iodide were evaluated. With the promise of flotation providing a cheap and large-scale process for the upgrading of low-grade ores and magnetic concentrates, the iron ore industry has made a sustained search over the years for a flotation reagent of general applicability and high selectivity. Having shelves full of commercial reagents already on hand and anticipating more, both the users and the suppliers are in need of an experimental approach sensitive enough to differentiate the individual characteristics in each group of reagents. Therefore, the adsorption behavior of various flotation reagents on mineral surfaces from aqueous solutions has been a subject of much investigation. The current view of adsorption based on the electrical double-layer theory is formulated on the assumption that certain ions in solution act as potential-determining ions. Their concentrations fix the potential drop across the double layer and their adsorptions govern the surface charge.&apos; Two methods used to study the adsorption

Jan 1, 1971

By E. E. Wark, J. Rogers, I. W. Wark, K. L. Sutherland

SOAPS have been used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xanthates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present eminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies.[t] A broad, semi quantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. THE PARAFFIN CHAIN SALTS The basic requirements for a "collector" in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polarnonpolar compounds is the paraffin chain salts: CH3(CH2) „X where X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -CO2Na, -SO3Na, -SO4Na, - PO4Na2, or an aminonitrogen group, the

Jan 1, 1946