Search Documents

By C. S. Allen

WITH increased coal production and mechanization of coal mines many transportation problems arise. The main objective is to bring the coal to the tipple or dump it as quickly as possible. Larger and faster haulage locomotives or two locomotives connected in tandem have been adopted to solve the problem. Motor equipment, gears and control systems of locomotives to be placed on these hauls are carefully studied to meet these requirements, by an analysis of motor characteristic curves with the corresponding tractive effort curves, in order to determine the correct load for maximum efficiency and to determine the approximate schedule. Control equipment is usually considered to be the controller and resistance. Sometimes accelerating curves are calculated in order to obtain smooth starting in the least possible time without slipping the wheels. Train control is very important, but why limit this to acceleration? Deceleration or retardation of the locomotive is a part of the train control and should be given as much consideration as the control for acceleration. TYPES OF BRAKING Common braking systems for mine locomotives utilize screw-type mechanical brakes, dynamic braking and the air brake. For gathering and haulage locomotives, the screw-type mechanical brake is regarded as standard. A brake of this kind cannot be applied without much effort and lapse of time. Motormen, like other people, follow the path of least resistance, and therefore have their brakes ready for instant application-which means that the shoes are virtually dragging. Even then, a motorman bucks and plugs the motors to gain time and avoid as much physical effort as possible. "Bucking of motors" consists in turning the reverse cylinder of the controller to parallel position corresponding to the opposite direction of travel while the locomotive is in motion, without applying power from an external source. When this occurs, both motors tend to act as series generators, because the armatures are revolving and there is residual magnetism in the field circuit. Owing to slight differences in motor manufacture, one of these will generate a slightly higher potential and will overcome the generated voltage of the second and tend to drive it as a motor in the reverse direction. This action retards the locomotive but is very severe on the segments of the reverse cylinder and on the motor commutators. "Plugging motors" is the application of power to the motors corresponding to the opposite direction of travel. In order to "plug" the motors it is necessary first to "buck" them (which reverses the connections to the motors) and then to apply

Jan 1, 1941

By R. O. Neal

There are two main sources of the water that floods productive oil or gas sands. The water may rise from the lower depths of the producing stratum, or it may come from beds above or below the oil-bearing formation. Usually the recovery of oil is decreased by water entering the oil sands, and most oil-field waters, especially those of deep wells, tend to foster the formation of an emulsion, which is expensive to treat. This paper deals with a method of distinguishing between waters that encroach upon oil-bearing beds from sources in the same stratum and waters that reach the oil sands from horizons above. In order to remedy effectually water difficulties in oil and gas wells, it is absolutely necessary to determine the source of the invading water. Sometimes evidence such as the structural relations between the strata penetrated by deighboring wells and those found in the well under investigation is not adequate; also, data from drill logs and well records, from mechanical tests made on the wells by plugs, testers, drilling tools, etc., and from tests by chemical indicators such as eosin and Venetian red, may be unsatisfactory, for such data may fail to locate the source of the infiltrating waters. As a resort in such cases, the application of chemical analyses, that is, the comparison of an analysis of the water in question with that of typical waters from the various water horizons in that particular district, has in certain instances proved of value. This method has been used to advantage in the Westside Coalinga field of California, where the source of water may be fairly definitely determined , from its composition. The chief conclusions concerning the chemistry of the oil-field waters in California by G. S. Rogers1 are: "Oil-field water is not necessarily salty, as is generally believed, and may not be even slightly salty to the taste. The degree of concentration of chloride in such water is governed primarily by local conditions and is not affected by the position of the water in relation to oil. Sulfate diminishes in amount as the

Jan 1, 1920

By D. Coutsouradis, L. Habraken, P. Nicolaides

The TTT curves of 0.1 pct C, 13 pct Cr steels containing up to 12 pct Co have been determined in order to establish whether the effect of cobalt is similar to that observed m plain carbon steels. It is shown that cobalt increases the incubation time and decreases the transformation rate, though not in an uniform way. The bainitic transfornation is displaced to lower temperature and overlaps partially the martensitic zone. ThE effect of cobalt on the transformation of a plain carbon austenite has been studied by many investi-gators.'-3 It was shown that cobalt displaces the TTT curves to shorter times and diminishes the harden-ability. The interpretations given for this effect of cobalt are conflicting. According to E. Houdremont,4 cobalt increases the transformation rate of austenite because it increases the diffusion of carbon as shown in the experiments of E. Houdremont and H.Schrader,' R.Smoluchowski,5 and M. Blanter.6 On the other hand, M. Hawites and R. Mehl3 deny on the basis of their own experiments any effect of cobalt on the diffusion of carbon and they assume that an explanation should be found in an eventual effect of cobalt on the mechanism of nucleation and growth of pearlite. W. C. Hagel, G. M. Pound, and R. F. Mehl7 have shown by calorimetric measurements that cobalt increases the free energy of the austenite-pearlite transformation in an eutectoid steel and this result explains qualitatively the observed effect of cobalt on the rate of nucleation and growth of pearlite. The purpose of this research was to see by determination of TTT curves, if this same effect exists in 13 pct Cr steels. EXPERIMENTAL PROCEDURES The preparation of the alloys was carried out in an

Jan 1, 1960

By Philip W. Simmons

THE Colorado Plateau uranium province is in a mining boom rivaling the most colorful days of the early West. The application of scientific skills and the use of modern and novel mechanical equipment, however, is unique. No metal has ever received such concentrated effort from geologists and mining engineers. Moreover, no other metal has had the variety of tools available for finding and mining ores. Radiation detection equipment, bull- dozers, truck-mounted wagon and core drills, jeeps, airplanes, helicopters, tractor loaders, self -propelled 3-wheeled dump cars, front-end loaders and fleets of modern trucks are some of the present-day tools of the uranium prospector and miner. Because uranium is so vital to our national defense, the Atomic Energy Commission has offered many incentives for its mining. Through a series of circulars, the AEC has established base price schedules and various incentive payments. The incentive payments for acceptable ores from domestic mines are: (1) a guaranteed base price of $3.50 per Ib for ores assaying 0.20 pct U3O8 and more; (2) premiums based on grades above 0.20 pct U3O8 as for example, ores assaying above 0.50 pct U3O8 receive $1.00 per lb premium; (3) a development allowance of 506 per Ib of U3O8 contained in ores assaying over 0.10 pct U3O8 (4) an ore haulage allowance of 64 a ton mile for a maximum of 100 miles; and (5) an initial production bonus which may amount to as much as $35,000 in addition to all other payments. The producers have been guaranteed this policy until Feb. 28, 1957. The other four will continue until April 1962.

Jan 4, 1954

By Arthur E. Bousu, C. T. Eddy, L. W. Eastwood

THE recrystallization and grain-growth phenomena of cold-worked metals have considerable industrial importance because of their role in the fabrication of metals. For this reason, and because of the general academic interest in the subject, these processes have received considerable attention since the time of J. E. Stead's paper1 on The Crystalline Structure of Iron and Steel. There are considerable differences of opinion regarding the theory of recrystallization and grain growth and also differences in the observation of the modus operandi of the processes themselves. The value of many of the existing quantitative data on grain growth is decreased by the failure to distinguish between the grain sizes just after complete recrystallization and those resulting from coalescence. For this reason also, the value of the diagrams of stable grain sizes, like those produced by . Bass and Glocker2 and Czochralski3, is lessened in so far as an interpretation of the facts of recrystallization is concerned. It is hoped that the data presented in this paper will help to clarify and to simplify the facts relating to recrystallization, and at the same time will show that some of the present-day conceptions are untenable. A paper on the theory of recrystallization with additional data will be completed in the near future by the writers.

Jan 1, 1935

By David R. Mitchell, R. B. Hewes

MANY processes for cleaning coal that are in use depend primarily on physical properties of coal and refuse other than specific gravity and surface conditions relating to froth flotation. These properties are shape, coefficient of sliding friction, resilience, friability, magnetic susceptibility, and electrical conductivity. In many of these processes specific gravity does have some effect and many separators are designed to utilize more than one of the physical properties cited. Although the processes described herein do not have a widespread application, yet for specific coals and specific conditions, they are economically important. A problem confronting many coal-mining districts is the marketing of the slacks or screenings and dust passing the final sizing screens. Processes in commercial use installed primarily to increase the form value, and hence the market value, of these slacks and dusts include briquetting, packaging, and low-temperature carbonization. MECHANICAL PICKERS Machines utilizing shape, frictional resistance, and differences in resilience of coal and impurities are usually called mechanical pickers. They require a closely sized feed, therefore their use is confined to the pea, nut, and egg sizes. Various types of these devices are described by Berrisford, 1, 2 Taggart,3 and Peele.4 Shape In general, coal differs in shape from its accompanying dirt throughout the range of commercial sizes. Coal, breaking into roughly cubical particles, contains a greater number of axes that are approximately the same length than does the dirt. The latter, consisting of pieces of slate and shale and lenses of pyrite, is flatter in nature. Further, flat coal often has a dirty, slaty appearance, even though of high quality. Mechanical pickers known as flat pickers, or "flatters," are widely used in the Pennsylvania anthracite region to remove flat coal .from the final clean coal. This practice greatly improves the appearance of the final market product. Flat pickers for removing impurities or flat coal ("flats") are usually installed on shaker screens, shaking conveyors, and chutes. In Fig. 1 three

Jan 1, 1950

By J. A. Herbst, G. E. Agar

The effect of fluid viscosity on the classification of solids in a liquid-solid cyclone was investigated. The separation size was found to be proportional to Additionally, it was found that the prediction of flow rate through a cyclone is dependent on a Reynolds criterion. Above a critical value, the flow can be predicted by a simple equation, whereas, below this value a variable orifice coefficient must be introduced. INTRODUCTION The solid-liquid cyclone is widely used as a device for classification, thickening, and heavy media separations. The more important variables and how they affect the performance of a cyclone are known and have been the subject of several investigations.' In general, these studies have paid little attention to the viscosity and those which have, introduced it through Stokes settling considerations. Systems which contain appreciable amounts of swelling clays exhibit viscosities much greater than water, and in these systems the viscosity term becomes important in determining the separation size. The work described here was done to determine in a Newtonian system the dependence of separation size on viscosity. BACKGROUND The separation size for a cyclone classifier has been related to the parameters of the cyclone by an equation of the form: where a is probably between 1.3 and 1.5, ß is between 0.50 and 0.57, and 6 has a theoretical value of 0.5. where y has a value between 1.8 and 2.0. Although these relationships are empirical, equations that differ only in the exponents have been derived from theoretical considerations. Those interested in the origin of these equations are referred to some of the original work.6,7 MATERIALS AND PROCEDURE The laboratory apparatus used in this study is pictured diagramatically in Fig. 1. Feed slurry was pumped from an agitated 15-gallon plastic tank by a centrifugal pump driven by 3/4 hp motor. The static pressure of the feedstream and thus the pressure drop through the cyclone was measured on a gage located as close to inlet of the cyclone as possible. When samples were not being taken, overflow and

Jan 1, 1967

TO THE BOARD OF DIRECTORS AND THE MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -It is pleasant to be able to report that the year just closed has been a prosperous and successful one for the Institute As is shown by the reports of the Treasurer and the Finance Committee, the business affairs of this organization are in excellent condition With property valued at more than three-quarters of a million dollars, and with con¬siderable sums in various funds and endowments, it is possible to spend on each member of whatever class $22 65 each year, more than the maxi¬mum amount of dues received from any one, and substantially twice the average amount, $10.94, received from all To do this has required close management and a strict regard for our limitations In 1926, when the Budget was made up, the estimated expenditures for the work which it was felt the Institute must do exceeded the estimated receipts by some $14,000. At the close of the year, despite a` number of unexpected decreases in receipts, it had proved possible to accomplish substantially all the work laid out and close the books with the usual transfer of initia¬tion fees to the General Reserve, and still only reduce the cash balance $2,074 54. This was made possible by the hearty and loyal cooperation of the whole staff of employees and the extremely large amount of gratui¬tous service rendered by the officers, the members of the Divisions and technical Committees, and the membership generally Even so it was impossible, because of limitations of funds, to undertake many things it is highly desirable for the Institute to do, and it was necessary to refuse the publication of important papers and committee studies, because of the lack of funds.

Jan 1, 1923

By Allan Clark

(San Francisco Meeting, September, 1915) IT is nearly three years since the metallurgy of the Homestake ore was discussed with considerable thoroughness, in a paper' read before the Institution of Mining and Metallurgy. Certain changes have been made in this period which are perhaps of sufficient interest to justify a brief description, and it is chiefly with such details and miscellanies that this paper will deal. In the circumstances, a certain amount of repetition is inevitable, but matter treated of in the former paper will be referred to here only when it is necessary for the sake of coherency. For full descriptions of equipment and technique, the former paper should be consulted. The mineralized slates and schists which constitute the ore vary considerably in composition, but the unoxidized ore, perhaps constituting the major part of the reserves, contains either chlorite or hornblende (cummingtonite), with quartz, carbonates of lime, magnesia and iron, and arsenopyrite, pyrite, and pyrrhotite. Ferrous minerals predominate, and this fact has been an important factor in determining the metallurgical treatment. With one or two exceptions the minerals noted are of relatively high specific gravity, and the ore as a whole is exceptionally heavy, many determinations giving an average specific gravity of 3.00. This high specific gravity presents one decided advantage, when the' cost of treatment is compared with operations elsewhere, in that the ton, almost universally the basic unit, represents a volume probably less by 10 per cent. than that of many gold ores. On the other hand, this high gravity renders more difficult the discharge of pulp from mortars, its distribution on amalgam tables, and its transportation in launders.

Jan 7, 1915

By Albert Sauveur

Floris Osmond, Honorary Member of the American Institute of Mining Engineers, born in Paris, March 10, 1849, died at Saint-Leu near that city, June 18, 1912. Taken suddenly ill with congestion of the brain while on his way from Paris to his home, he reached it in time to write on the typewriter his last wishes, one of which was that no biographical notice of his life should be published. Holding Osmond's memory sacred, as those who have known him will, is it our duty to conform with his desire ? Shall no mention be made in our Transactions of the beautiful life and great achievements of one of our most honored members? Is it not, on the contrary, incumbent upon us to disregard Osmond's instruction in this matter and to place on record our admiration for the nobility of his life, for his talents and for the importance of his work, that younger men may be inspired by it with a desire to be guided by worthy motives in the path of unselfish pursuits ? I cannot feel that in following this course I am disloyal to Osmond's memory and I am strengthened in this belief by the opinion of men of high honor whom I have consulted before undertaking the writing of this obituary notice. One of them, Professor Henry M. Howe, justifies my decision better than I could do it myself when he writes : " Let us look frankly at the matter. Here we have a most extraordinary life, a life of rare beauty and power of inspiration to the rest of mankind. In my opinion we should not deprive mankind of the stimulating influence of the example of M. Osmond simply because he shrank from publicity. Our young men see every day how greed and vulgar push succeed, and with what material rewards they are crowned. They see too rarely the more valuable crown which comes to self devotion. A permanent and public recognition of the beautiful qualities of Osmond's life cannot fail to appeal to the imagination of young men and to help to deflect them toward leading a noble rather than a sordid life. Therefore I feel that the Revue de Métallurgie and other bodies owe it to the public to give prominence to his career by means of biographical notices."

Jan 1, 1914

By Nicholas J. Grant, Laszlo J. Bonis

Two dilute nickel alloys in each of the systems Ni-Al, Ni-Ti, Ni-Cr, and Ni-Si u:ere internally oxidized at 700° to 900°C for time periods up to 100hr to establish the oxide particle size, depth of oxide penetration, and the change in oxide particle size with depth. Fine (-270) mesh alloy powders were then intevruzlly oxidized, hydrogen sintered, compacted, and extrmded, yielding bar stock for tensile tests at room temperature and creep-mpture tests at 815° to 1093°C. Recrystallization studies were made up to 1400OC. ReCENT studies have clearly indicated that oxide dispersion strengthened alloys exhibit outstanding elevated temperature properties, espe- cially in long-time tests. Certain structural parameters must be observed to achieve optimum properties, namely, micron or submicron interpar-ticle spacing, submicron oxide particle size, and a high level of stored energy.'-5 A number of processes have been utilized to obtain the desired structures, but certain of them appear to offer greater promise. Thus far the most promising method is the internal oxidation of dilute alloys consisting of a relatively noble solvent metal and a readily oxidizable solute element.3'6)7 Several important principles governing internal oxidation have been established in earlier studies;' however, these principles are as yet not adequate to permit alloy development studies. Much of the earlier work was performed on relatively coarse wires or in idealized systems. As a result, there are still a number of unanswered questions which require considerable additional work: a) How does oxide particle size change with depth of penetration of the oxide? How does this vary with the specific type of solute element? b) What is the effect of solute content on the average oxide particle size?

Jan 1, 1962

By J. W. Stewart

THE aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula. Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I). It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the 15 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remain¬ing to schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year. PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1941

By John C. F. Randolph

This establishment being now in full working order, it has seemed of considerable professional interest to collect together, in a concise form, the various points as to its plan, method of dressing, and equipment. The data contained in this paper have been largely drawn from the able paper of E. Kutscher, constrnoting engineer of the works, contained in the Zeitschrift fur Berg-HÜtten-und Salinenwesen im Preussischen Staate, 1873, supplemented by some personal memoranda made while the works were under construction and by memoranda on the works appearing in various German technical papers from their completion up to date. This is probably the largest dressing works in the world devoted to the beneficiation of argentiferous lead ores, and it is doubtful if any establishment for the concentration of mineral of any description can compare with it in size. As showing the final practice adopted in an old and very conservative mining region, in which the concentration of ores has been a matter of constant practice and experiment for a very long period, these works are of peculiar interest. The fact that the Clausthal ores strongly resemble a very large and abundant class of ores found in the United States has always attracted the attention of American mining engineers and mine owners to the methods employed in dressing and smelting them. The study of their methods of concentration of ores has, however, always been full of difficulty,

Jan 1, 1879

Jan 1, 1956

• The Venezuelan Trade Mission to the United States announced that Bethlehem Steel Corp. will begin exporting iron ore from its El Pao concession, south of the Orinoco River in Venezuela, in about three months. The ore will be transported by rail from the mines to barges on the Orinoco and transshipped to ore vessels at the coast for shipment to the Sparrows Point, Md., plant. The Latin American business men warned that projected increases in the United States tariff on petroleum imports from Venezuela would force that country into bilateral trade agreements with other countries and would mean drastic curtailment of Venezuelan imports from this country. •Bethlehem, South American Gold and Platinum Co., and U. S. Steel are investigating the possibilities of securing American foodstuff for their South American mining camp commissaries through the International Basic Economy Corp. IBEC buys in quantity to supply its subsidiary companies operating in Venezuela and Brazil. The mining companies will rid themselves of this burdensome task as well as realizing a saving from the bulk purchases of IBEC. •Oliver Iron Mining Co. has begun construction of a fine ore and taconite agglomeration plant at Virginia, Minn. It is expected to be ready in six months. The plant will be used to experiment with the making of clinker cakes and egg-sized lumps by sintering machines and nodulizing kilns respectively; about 1 million tons per year will be produced. • Roof pinning has been adopted at the iron mines of TCI, near Birmingham, to support overlying strata as mining progresses. Favorable results have been obtained in that dilution of the ore has been reduced by 50% which is attributable to this method of supporting the roof. •An American mining engineering team has gone to Turkey for a two-year assignment assisting Turkish government agencies in the $45 million ECA development, mechanization, and construction of cleaning plants for the Zonguldak coal field, 200 miles east of Istanbul on the Black Sea. The group consists of James Beeley, John E. Good, John S. Lambright, David Renshaw, and Charles R. Weir, all of the Paul Weir Co. •Arthur F. Taggart describes a new way of training engineers by emphasis on broad, basic engineering courses on page 460 of this issue. •Lawrence T. Tierney, chairman of the National Bituminous Coal Advisory Council, released a report stating that the increase in oil imports since the latter part of 194$ has caused significant damage to the U. S. fuel economy. It has reduced the strength of and employment opportunities in the coal, domestic petroleum, and transportation industries, as well as in related service and supplier fields. •Women, camels, and donkeys are the beasts of burden of the Sahara, according-to the UNESCO World Review. •Increased demand for magnesium sheet in airplane construction ana other phases of the national security program have led Alcoa to establish a sheet magnesium rolling division at its New Kensington, Pa., works which will begin operation shortly. Novel prospecting methods being used by the USGS in its search for uranium include: shock-mounted instruments in light trucks,. Geiger-counter probes lowered into augur holes, and experimental airborne prospecting.

Jan 4, 1950

By C. S. Matthews, H. C. Lefkovits

The purposes of this study are (a) to determine the accuracy of a previously proposed method for calclrlating average reservoir pressure and (b) to find a method for estimating the shape of the drainage area of each well in a bounded reservoir. Both numerical and experimental methods are used to determine the pressure distribution and the location of drainage bounrlaries in idealized reservoirs at steady state. A number of photographs are included which show flowlines and drainage areas in reservoir models of various shapes. Results from these studies are then compared with those from the previously proposed method for calculating average reservoir pressure.' It is concluded that the previously proposed method is sufficiently accurate for most reservoir engineering purposes. In addition, some simple methods are given for estimation of .shapes of drainage boundaries. INTRODUCTION A method for the determination of the average Pressure in a bounded reservoir was previously developed by Matthews, Brons, and Hazebroek,1 and presented at the Petroleum Branch Fall Meeting in 1953.† In aP- plying this method, the reservoir was first divided into drainage volumes; second, the average pressure in each drainage volume was calculated; and third, these drainage volume pressures were averaged volumetrically to give the average pressure in the reservoir. It was shown that each well's individual drainage volume, at steady state, is proportional to the well's production rate; however. the question of how to estimate accurately the shape of these drainage volumes could not be answered. Furthermore, in calculating the average pressure for each drainage area, the actual drainage areas, which are in general quite asymmetric in shape, are replaced with one of the symmetric prototypes given in T.P. 3876. A question may then be raised as to how accurately the symmetrical figures depict the pressure behavior of the actual unsymmetrical drainage areas. The study reported on in the present paper was made in an attempt to shed light on the above questions. METHODS It was shown in T.P. 3876 that after a period of steady rate of withdrawal the rate of pressure decline becomes constant at every point in a bounded reservoir containing a single-phase fluid whose compressibility is small and constant and whose viscosity is con-

Jan 1, 1956

By J. Chipman, J. C. Fulton

Reduction of silicon from blast-furnace-type slags by carbon-saturated iron is a very slow reaction even under conditions of rapid stirring. Equilibrium under atmospheric pressure of carbon monoxide was approached from both sides, and the silica-silicon relation was established at temperatures of 1425º to 1700°C for slags containing up to 20 pct Al2O3. Silicon carbide is formed by reaction of graphite with high silica slags and the conditions for its formation were determined. Activities of SiO2 and of CaO in their binary solutions at 1600°C were determined. The effects on the activity of SiO2 were established for additions of 10 to 20 pct AI2O3 and of 10 pct MgO. STUDIES of chemical reactions between blast-*>-5 furnace slags and metal have been focussed on the transfer of sulphur from metal to slag. The important role which silica reduction plays in this process' has led to a study of the transfer of silicon from slag to metal and the equilibrium represented by the equation SiO2 (in slag) + 2C (graphite) = Si + 2CO (g). [I.] The authors2 have published an account of the experimental method employed in attacking this problem and of three series of experimental results at 1600°C. This paper contains data on some additional compositions and extends the observations to cover the temperature range 1425° to 1700°C. The data are used to determine the activity of silica in the slags. As in the earlier experiments, the atmosphere was carbon monoxide which flowed through the furnace at 150 ml per min. In certain heats designated in the tables and figures, the gas was bubbled through the melt using a graphite tube. The latter increased in porosity during a run and in some cases bubbling ceased as indicated by cessation of surging. Some results were discarded for this reason. Experimental Results The new data are shown in Tables I through V and both old and new data are plotted in Figs. 1

Jan 1, 1955

By George R. Gardner, Kenneth B. Ray

THE application of wet cleaning processes for the beneficiation of bituminous coal has created in some localities a problem in the recovery and disposal of fine solids in the washery water. The maximum allowable concentration of these solids in the washery circuit that is consistent with satisfactory operation of the cleaning units remains a controversial point. It has, however, been generally recognized for a number of years that some degree of control should be exerted over the concentration of such material. Early methods of control involved intermittent or continuous discharge of a portion of the plant slurry into near-by streams or settling ponds, and this persisted even after the adoption of settling tanks or cones. The practice is not always economical, for two reasons: first, because of the waste of coal, and, second, because it is sometimes difficult and expensive to obtain an adequate supply of water. The latter condition often is aggravated by chemical treatment of the make-up water that is necessary to prevent excessive corrosion of plant equipment. The modern approach to this problem has been the adoption of continuous thickening devices. However, because such equipment occupies considerable plant space and is somewhat expensive to construct, the practice of loading these thickeners beyond their rated capacity is widespread, therefore often the performance of such units is not altogether satisfactory. In recent years, European washeries have increased the rate of settling of the fine coal from the slurry by the addition of specially prepared starch solutions. These reagents cause flocculation of the solid particles and thereby increase the rate of sedimentation. The first important work on the flocculation and clarification of coal slurry was done by Henry, who developed the Henry process and used it successfully in Belgian preparation plants. Soon after the initiation in Belgium, the process was introduced into England, where subsequent investigation developed similar processes, which were successfully used in

Jan 1, 1939

By A. R. Kaufman, P. Gordon, C. H. Schramm

AS a part of the general program on alloys of uranium carried out at the Massachusetts Institute of Technology under contract W-7405-eng-175 for the Manhattan Project during the recent war, it was considered desirable to investigate the boundary binary phase diagrams of the ternary alloy system uranium-tungsten-tantalum. Previous work on these alloys was practically nonexistent. A brief statement to the effect that tantalum and tungsten form a continuous series of solid solutions was found in a general paper on tantalum by W. V. Bolton1 but no information was available on the uranium-tungsten and uranium-tantalum systems. The research to be described in this paper has served to delineate the main features of the uranium-tungsten, uranium-tantalum phase diagrams and to check Bolton's work on the tungsten-tantalum diagram. Experimental Details Metals: The tungsten and tantalum used for preparing the alloys were 99.96 and 99.65 pct pure, respectively. The chief impurities in the metals were about 0.02 pct molybdenum in the tungsten, and 0.2 pct columbium, 0.05 pct tungsten, 0.02 pct barium and 0.01 pct silicon in the tantalum. The uranium used was 99.9 pct pure, with the main contaminants being iron and carbon. (An appreciable amount of magnesium was present in the uranium as received, but this distilled off during melting and so is not reported as an impurity.) The composition of specimens indicated in the subsequent figures and tables of this paper are the results of chemical analyses on the cast alloys except for the tantalum-tungsten alloys. For the latter, chemical analysis was not very reliable as a result of the difficulty of separating tungsten and tantalum chemically. Consequently, the nominal

Jan 1, 1951

By William Fink

ALUMINUM forms not only binary compounds with most of the metallic elements but also forms many ternary or more complex constituents. Several of those occurring in the more important alloy systems have been identified under the microscope and the action of various etching reagents has, been carefully studied.' The determination of the structure and composition of these complex constituents is a matter of some difficulty and little information is available. X-ray crystal analysis offers a promising method for the study of such constituents. First, and of considerable importance, is the possibility of recognizing the presence of a given constituent by means more positive than microscopic observation. Evidence can also be obtained concerning the nature and composition of the constituent in question and ultimately it should be possible, at least in some cases, to describe the structure including the relative locations of the various atoms. In this paper some results of an uncompleted study of the constituents of the aluminum-iron-silicon system are given and the methods employed are described. Inasmuch as iron and silicon are the chief impurities in aluminum, the constitutional relations of this system are of fundamental importance in the metallurgy of pure aluminum and its alloys; the system has been studied by several investigators and the more important contributions have been reviewed recently.2 Fig. 1 shows the structure of the aluminum-rich alloys after prolonged annealing at 560° C., in accord with one of the most recent investigations.3 The ternary alloys examined in the course of the present investigation were all annealed at 550° or 560° C.; in fact, some of the specimens were the identical ones used by Dix and Heath, who kindly supplied them for this work. Since the results

Jan 1, 1930