Search Documents

By Joseph D. McClung, L. G. Austin

INTRODUCTION Run-of-mine (ROM) coal generally falls into two major groups, that from underground mining (continuous mining machines) and that from strip mining. Continuous miners produce a finer product and strip mining a coarser product that is crushed to produce the desired size. Further size reduction depends on the proposed use or uses for the coal. For example, for pulverized coal power plants as a rough general rule, the coal is ground or pulverized to 80% less than 200 mesh (0.075 mrn) before it is blown into the boiler furnace as a coal-air suspension. For solvent-refined coal processes, the desired size is about <30 mesh ( <0.60 mm) ; in fluidized bed uses, the coal is typically < in. ( < 1.6 mm); for Lurgi pressure gasifiers, the desired size is 1-2 1/2 in. (25-63 mm). Coal preparation plants typically work with a coarse size fraction of 6x1 1/4 in. (15Ox32mm). It seems probable that the next decades will see much wider application of coal cleaning before use and that the stages of crushing and pulverization from ROM coal to end use will be integrated with coal cleaning processes. Since different cleaning processes work better with different ranges of coal size and the degree of cleaning possible is inti-

Jan 1, 1979

By A. W. Edelen, H. V. Lee

THE Teziutlan copper-zinc deposit is supposed to be of late Cambrian or early Paleozoic age. The country rocks are a series of schists or phyllites, flat lying and in the form of a plunging anticline. The ore deposit occupies a single horizon in the schist for a known horizontal extent of 1200 meters. Along its strike occur four large lenses or ore bodies. These ore bodies occupy positions along the flank and extend to the crest of the anticline. The primary mineralization is in the form of quartz, pyrite, sphalerite, chalcopyrite and galena, with a few scattered silver anti-monides. Quartz and pyrite form the mineralization between the ore lenses. In the ore lenses the sulphides appear as a massive, very he-grained intergrowth of minerals. The intergrowth suggests a contemporaneous deposition of the heavy sulphides. The grain size, usually under 0.09 mm., makes the separation difficult and fine grinding important. The ore bodies were formed at great depth by solutions probably originating in the same basic magma that gave rise to the dolerite sills that are so common in their vicinity. INTRODUCTION The Teziutlan copper-zinc deposit is distinctly different from other ore deposits of Mexico in age and type. Previously stated to be pre- Cambrian in age, it is now quite generally supposed to belong to the late Cambrian or to the early Paleozoic period. Also, in contrast to the usual shallow-vein zone type of mineralization in Mexico, there is here exemplified an intermediate vein zone deposit of copper and zinc. So far as is known, the Teziutlan vein is unique in the history of Mexican geology and in a class by itself, its closest counterpart probably being the copper veins of the pre-Cambrian of Canada. The Teziutlan district is in the extreme northwestern corner of the State of Puebla, Mexico. Teziutlan, the terminus of a branch line of the National Railways from Mexico City, is connected to the mine at Aire Libre by a 17-km. narrow-gauge railroad owned and operated by the Teziutlan Copper Co. Owing to excessive grades on this short line, Shay-geared locomotives are used for the transportation of concentrates and supplies.

Jan 1, 1937

By J. J. Scott

During 1967 wage settlements and strikes ran at a high rate and it has been estimated that union gains of 4 ½ % to 5% per year have been attained in many instances. When these events are coupled with the need to operate on lower grade and deeper deposits the need for technological advances in underground mining becomes obvious. Emphasis has been on ways to reduce the number of manshifts required per ton of product. Most significant advances have been made in rapid advance of primary mine openings, development of mobile, rubber-tired, front-end loaders and hauling units, high-speed drilling with rotary and rotary percussive units and a serious look at nuclear devices to break large volumes of ore cheaply. Boring Developments in bit manufacture and metallurgy have allowed continuous boring-type machines to be used on harder formations than was deemed feasible in the past. Hecla Mining Co. has been using raise boring equipment for drilling 9 7/8 in. diam pilot holes in raises which are later reamed in an upward direction to 48 in. diam. The machine used is a J. S. Robbins model 42R raise borer which has been used successfully to drill two relatively long 48-in. diam holes. The first was 520 ft in length at a dip of 76º, and the second was a 785-ft vertical hole.

Jan 2, 1968

By R. L. Wilcox, M. L. Fuller

MOST commercial alloys undergo changes in phase composition after casting. This is a natural result of the fact that the alloys are not in a state of phase equilibrium as cast and phase changes will therefore take place, with more or less rapidity, in an attempt to attain equilibrium. The practical aspect of aging in zinc-alloy die castings concerns the changes in physical properties and in dimensions that may accompany aging phase changes. Harmful alterations have been reduced to a minimum and zinc-alloy die castings are being produced today that are so stable with respect to dimensions and physical properties that they are entirely suitable for most practical purposes1. In the first paper2 of this series, and in this paper, aging phase changes of zinc alloy die castings have been investigated and the possible influence of these changes on dimensional changes of the castings has been evaluated and compared with the dimensional changes actually experienced. The change of dimensions has been selected for practical comparison in these papers because the effect of phase changes on the dimensions of a casting is directly calculable from X-ray crystal-analysis data of the phase structure. The die-casting alloys considered contain, in addition to zinc, 4 per cent of aluminum, about 0.03 per cent magnesium, and from 0 to 3 per cent of copper. It was shown in the former paper that the eutectoidal decomposition of the beta aluminum-zinc phase, while intrinsically capable of causing a considerable shrinkage, can have very little effect on the observed shrinkage of die castings because it takes place within a few days of aging, whereas the observed shrinkage continues for five weeks. It was therefore concluded that the other existing phase change,

Jan 1, 1935

CONTENTS PAGE GEISMER, H. S.-Coal Washing Practice in Alabama. Discussed by William Kelly, H. S. Geismer, H. D. Pallister, L. E. Bryant, Milton H. Fies, Elmer F. Harris, James A. Barr, George G. Crawford, E. C. Wright, George S. Rice, R. V. Norris 1 MILLER, F. W.-Byproduct Coking in Alabama. Discussed by Theodore Swann 4 FIES, MILTON H.-Alabama Coal Mining Practice. Discussed by Milton 11. Fies, R. V. Norris, R. D. Hall, L. E. Bryant, George S. Rice, H. S. Geismer 5 MUSSEY, H. E.-Blast-furnace Practice in Alabama. Discussed by C. A. Meissner, Franklin H. Crockard, H. E. Mussey, W. H. Oldham 14 Coal Washing Practice in Alabama Discussion of paper of H. S. GEISMER, presented at the Birmingham Meeting, October 1924, and issued, as Paper No. 1363-C, with MINING AND METALLURGY, September, 1924. WILLIAM KELLY, Iron Mountain, Mich.-Is the dry-cleaning method used? H. S. GEISMER.-Neither the dry-cleaning process nor the Chance sand-liquid method has been tested in Alabama; but all other methods used for cleaning bituminous coal have been largely brought to perfection in this state. H. D. PALLISTER, Tuscaloosa, Ala.-Have you the results from the recent work on the tables with reference to fine coal? H. S. GEISMER.-None of the iron-producing companies has adopted the tables, though three commercial operators have installed tables within the last six months. I tried to learn the results, but they were not willing to release the data just now. At the mines producing domestic coal, fines present a difficult problem; until within the past six months all the fine coal was wasted. The operators are trying to recover some of it on the table. L. E. BRYANT, Rockwood, Tenn.-Is there any connection between the sulfur content of the sludge and the effect of the sludge on vegetation?

Jan 7, 1925

By T. E. Ockershauser

The Southwest Antioch Oil Field located in T2&3N - R2&3W, Garvin County, Okla., was discovered in February, 1946, by The Globe Oil & Refining Co. and The Vickers Petroleum Co. at their Melinda Gibson No. 1. Oil production was encountered at a depth of 6,525 ft in 14 ft of lower Pennsyl-vanian sandstone. The producing sand, locally called the ."Gibson" or "Third Deese," is a sand bar deposit strung along the west flank of the Pauls Valley uplift in a northwest-southeast direction. The oil reservoir is defined to the east by the edge of sand deposition along the uplift and to the west by the gradation of sand into shale. Within the Antioch Unit, the sand dips from 150 to 400 ft per mile southwesterly and has a pay thickness varying from 10 to 55 ft and averaging 28 ft. Several areas of Gibson production have been developed, including the Katie pool on the south, the Elmore Area of the Southwest Antioch Gibson Sand pool. the Southwest Antioch Gibson Sand pool proper, the Southwest Maysville pool and the New Hope pool on the north. Production extends over a belt 22 miles long by about two miles wide and is continuous except into the Katie and New Hope pools. It appears that drilling will soon prove these intervening areas productive. To March 1, 1950, approximately 18,000 acres have been developed with 450 Gibson wells. It is likely this count will ultimately reach 32.000 acres with 800 wells. RESERVOIR The natural production of oil from the Gibson reservoir is primarily due to solution gas expansion though gravity also plays a part. There is no indication of water drive or evidence that an initial gas cap existed. Gibson oil has a stock tank gravity of 43" API and was saturated at the original reservoir pressure of 2.925 psi. It contained 1,3440 cu ft of gas per bbl in solution and had a high shrinkage of 70 per cent. Connate water amounts to 15 per cent. Reservoir temperature is 130°F. Porosity averages 15.5 per cent and permeability ranges from less than one md to over 1.000. Based on meacurement of 400 core plugs from 15 wells, 78 per cent of the permeabilities fell within the 10 to 1,000 md bracket and averaged l67. Primary oil recovery is estimated at 140 bbl per acre-ft or 22 million bbl for the present 137-tract unit. Due to unitization

Jan 1, 1951

By Clifford S. Wilson

ScReened pipe is designed with the view of restraining the fine, free-running sands of the production zone from entering oil wells. Its successful use is dependent on a number of factors. The nature and effects of some of these factors can be determined through experiment and observation, but some of the elements that have a distinct bearing on the use of screened pipe can be evaluated only by estimate. The important subsurface conditions which affect the use of screened pipe are: 1. Depth of production zone. 2. Extent of production zone. 3. Reservoir pressure. 4. Character and relative quantity of oil and gas. 5. Character of sediments: a. Cossolidation of beds. b. Variation in beds. c. Grain-size gradation of sands. d. Free-running characteristics of sand from different levels. Aside from the use of mechanical equipment and tools, the measures to be taken in the installation of screened pipe involve: 1. Size of liner. 2. Length of liner. 3. Design and mesh of screen. 4. Portion of liner to be screened. 5. Manner of setting liner. 6. Preparation of or washing of the well before or during the setting of the screen. 7. Manner of bringing in the well. 8. Manner of flowing the well. Values applicable to the actual subsurface conditions that exist at any well can only be approximated. The accuracy of the estimate will be measured by the amount and quality of the evidence at hand and the personal factor of ability to interpret the evidence fairly, whether

Jan 1, 1933

By J. Donovan Jacobs

An underground excavation project usually is a highly organized complex of different but interrelated construction activities. It is the whole effort, including the necessary tools, which will be referred to as the System. Tunnel-driving and shaft-sinking operations are among the most systematic of construction efforts. Systems are not new in the performance of construction. It is the Systems Concept which seems only recently to have been discovered and made the subject of much study and discussion. HISTORICAL From the seventeenth century, when explosives were first utilized for rock excavation, until the successful application of the rotary-head continuous tunneler in this decade, the cyclical drill-blast-muck-support method has been standard tunnel-driving procedure throughout the world. Whatever improvements occurred were the result of development of better tools for performing the various operations of the cycle. The electric locomotive replaced the mule and permitted the use of larger muck cars. The steam drill, which ended the day of the double jack, was itself quickly made obsolete when compressed air replaced steam as the source of drilling energy. Power shovels were introduced to save the time and money involved in the hand-loading of excavated materials. A cubic yard of rock tunnel muck can be excavated today for just half the man-hours of labor required in 1948. Developments over 20 years which cumulatively have resulted in this economy include: drifter drills mounted on hydraulically controlled booms and positioners; tungsten-car- bide-tipped bits; long feed shells on the drifters, making it possible to drill the full depth of a round without changing steel; better designed,

Jan 1, 1970

By Geoffrey Gilbert

The Montana Phosphate Products Co., subsidiary of the Consolidated Mining and Smelting Company of Canada, operates three phosphate properties north and northeast of Garrison, Powell County, Mont. Production of all three is from the same phosphate bed, a 3 to 4-ft. member of the Phosphoria formation, whose outcrop is traceable across the mountains of the Garnet Range in a series of southeasterly pitching folds. Because of topographical differences and of variations in the attitude of the bed, each property has its own mining methods and problems. Most of the phosphate rock produced since 1930 has been shipped to the plant of the Consolidated Mining and Smelting Co. at Trail, B.C., where it is treated with sulphuric acid for conversion to phosphoric acid, which in turn is used to produce various fertilizers. History The occurrence of rock phosphate in Montana has been known since 1910, and the Garrison area was mapped by the United States Geological Survey in 1913. In the nineteen twenties William Anderson, owner of a ranch 8 miles north of Garrison, discovered phosphate on his land, and the Montana Phosphate Co., which later became the Montana Phosphate Products Co., was formed to work the deposit. Montana Phosphate Products Co. later obtained United States leases on two adjoining parcels of ground, and this combined property, known as the Anderson mine, has been the main source of Con-solidated&apos;s phosphate rock. The mine now includes an adjoining parcel leased from Anaconda and mined from the Anderson workings. In 1940, the Graveley mine, a small privately owned property 6 miles east of the Anderson, was leased from the owner by Montana Phosphate Products Co., and a U. S. lease held by Graveley on some adjoining ground was subleased. In 1943 the Luke mine, on the Mineral Hill property, 1 3/4 miles south-southwest of the Graveley, a U. S. lease, which previously had produced a few thousand tons, was optioned from the lessees by Montana Phosphate Products Co., and is now being developed. At both these mines the rock is appreciably higher grade than at the Anderson mine. Geology The Phosphoria formation is the Permian member of an extensive sequence of Paleozoic and Mesozoic rocks. It is underlain by Pennsylvanian (Quadrant) quartzite and Mississippian limestone, and overlain without any marked unconformity by Jurassic (Ellis) shale and Cretaceous shale and sandstone. In the Garrison area, the Phosphoria itself consists mainly of about 50 ft. of gray to yellow chert. Immediately below the chert is the phosphate, usually 3 to 4 ft. thick. Below the phosphate occur a few

Jan 1, 1948

By Gilbert H. Cady

Extensive sampling of coal in Illinois during the past 10 or 12 yegrs by the State Geological Survey, in cooperation with various organizations, such as the U. S. Bureau of Mines, the University of Illinois, and the Illinois Cooperative Mining Investigations, has made possible the delineation of two areas of low-sulfur coal in the southern part of Illinois. The $fur content is less than 1.25 per cent., so that, if otherwise suitable, these coals can be employed for metallurgical uses and for the manufacture of water-gas and retort gas. One of these areas is small and lies in Jackson County, near Murphysboro, the other is much larger and includes a large part of the famous Franklin County field. A small area of No. 2, or Murphysboro, coal has been worked for many years near the town of Murphysboro, Jackson County, Ill. In two mines, at least, the coal has a sulfur content of less than 1.25 per cent. It is doubtful, however, whether this field will ever be a source of large tonnage as the total area underlain by low-sulfur coal in workable thickness is probably less than 15 sq. mi. (24.14 sq. km.), and a large part of it has already been worked out.. The location of the area of low-sulfur coal in the Franklin County field is shown in the accompanying map. The small area underlain by the Murphysboro low-sulfur coal is shown near the town of that name in the central part of Jackson County. The larger area lies in the west side of Franklin County, extending also about 6 mi. (9.65 km.) south into Williamson County, about 4 mi. (6.43 km.) west into northern Jackson and western Perry County, and northward an undetermined distance into Jefferson County. All but the northern limit of the area is fairly well defined by sampling in numerous mines. The inner cross-lined area is underlain by coal having less than 1 per cent. sulfur, the outer boundary surrounding the area underlain by coal having less than 1.25 per cent. sulfur. The coal mined in the district is No. 6 or Herrin coal, commonly known as the Carterville or Franklin County coal. The bed has a thickness varying from about 8 ft. (2.4 m.) on the border of the low-sulfur area up to more than 10 ft. (3 m.) in the central portion, locally having a thick-

Jan 1, 1920

By Clarence Zener

THE internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites,4,5 localized weak regions introduced by cold-working,6,7 grain boundaries and possibly twinning planes.8,9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation. was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, ½ in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff.10 EXPERIMENTAL METHOD The experimental method used has previously been described in Institute papers.5,6,9 The measure of internal friction adopted here, 1/Q, is (1/p) X the logarithmic decrement, a measure used by some writers, and is also (1/2p) X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the funda¬mental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. EXPERIMENTAL RESULTS The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. 1, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of l00 during the next 100° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e~H/RT [I]

Jan 1, 1942

By Edwin Ludlow

IN CONSIDERING the waste in the coal industry, which is the title of this discussion, we must entirely eliminate the anthracite region. The demand for anthracite has been constantly increasing and the mines have been able to run during this last year, while the bituminous field was idle for two-thirds of the time. It is on a 100 per cent. basis, which is the best answer to any waste in industry investigations. The anthracite region is also in a very much better position on account of its control by very large companies which realize that their resources are limited; they must husband these resources in every way and they are making the most careful study of methods of mining and preparation to avoid any possibility of waste. This is well known and realized by the managers of those companies. Even the fine slush which was formerly thrown away is now being stored in the hope that methods will be found by which it can be used economically, either in briquet or pulverized fuel in coking. This has been tried. The anthracite factor may be dismissed from the waste in industry discussion, except as it applies to the general public that burns anthracite; there is a tremen-dous waste of anthracite in the burning of it. Looking at the ash piles where anthracite is burned and seeing the amount of carbon that comes away with the ashes, one realizes that proper efficiency is not obtained in the burning of that coal. Even its higher cost does not seem to bring people to a realization of the necessity of conserving and burning properly the entire coal carbon content of what has cost so large a price. Many people feel that they want to have the coal as large as they can shovel into the furnace; they do not realize that the small coal makes just as many heat units and can be bought at half the price. Consequently, the demand is continually in excess of the probable pro-duction for the larger sizes of anthracite, while the smaller sizes, such as large buckwheat and pea, are a drug on the market and can be bought at nearly half the figure; and yet, if properly burned, these produce just as much heat and can be used with a much greater economy than the large egg and stove.

Jan 3, 1922

By Lloyd Jones

THE strip industry made rapid strides in regard to both width and gage until about 1922, when the maximum width was about 20 in. In the hot mills, strips of thin gages in wide widths could be pro-duced, but only at a sacrifice of length of coil, con-siderable increase in power, and decreased tonnage out-put on the min. Hot mills, like the Bray sheet mill and the modern strip and skelp mills, demonstrated that . wider strip could readily be rolled, if such a product was desired. The strip manufacturers were really limited in width, not by the hot strip, but by the cold rolling of wide strip. This factor was roll pressure. The diameter of rolls increased as the width of strip increased. For cold rolling strip 20 in. wide, cold rolls were approximately 20 in. diameter. As the rolls became larger, the arc of contact between the rolls and the strip increased approximately, according to the formula, b=\/Rd where b = the width of contact R = roll radius d = total reduction Now the crushing strength of cold steel of low carbon varies from 70,000 to 100,000 lb. per sq. in. With each succeeding pass the crushing strength increases and may approach 250,000 lb., according to the total reduction. The total reduction in cold rolling of low-carbon steel will range from 40 to 70 per cent of the original thickness, usually in about three or four passes. On this basis, assuming a reduction of 20 per cent in one pass, the crushing strength of steel assumed at 120,000 lb., we have a total pressure between rolls, which (assuming that the rolls do not deform) equals: Roll Strip Strip Diameter, Width, Thickness, In. In. In. Pounds 10 10 0.100 380,000 20 20 0.100 1,080,000 30 36 0.100 2,375,000 42 50 0.100 3,900,000 These figures are approximate, but you will note that in increasing the width five times, or 50 in., the total pressure between the rolls increased approximately ten times. In other words, the pressure per inch of width increased from 38,000 to 78,000 lb. for the same per-centage of reduction.

Jan 3, 1928

By H. E. Rorschach

Activity in the oil and gas fields of Oklahoma was more pronounced in 1935 than in 1934, with 2320 completions, an increase of about 21 per cent. The state produced approximately 185,000,000 bbl. in 1935. Osage County and shallow pools in northeastern Oklahoma showed considerable activity. The assembly of a complete table of the oil fields of the state (Table 1) was not achieved, as many of the early records of operators and pipe line companies are not complete, and data for the older fields will perhaps never be fully tabulated. Table 1 includes all of the new fields and most of the important fields of the State of Oklahoma. Increased Field Activities The discovery of large production in the deep Simpson group in the old Fox field in Carter County in the southern part of the state, the discovery of new producing horizons in the Fitts pool, and the extension of Wilcox production in the "Mansion" area at Oklahoma City were the outstanding developments in Oklahoma in 1935. Wildcatting resulted in the discovery of new pools such as Jesse, Hoyt, Grayson, South Keokuk, Wofford, Britton and Stillwater. The Fitts and Edmond pools were rapidly developed during the year. Fox Pool.—Deep production in southern Oklahoma became a reality in October when the Williams No. 1 well of Carter Oil Co. and others, in the Fox pool, began producing oil at the rate of 10,000 bbl. per day from a depth of 8088 ft. After flowing wild several days, the well was killed after pipe stuck and a difficult fishing job resulted. The job had not been completed at the end of the year 1935. This test, considered one of the most important oil discoveries in the Mid-Continent area, opened the entire South Oklahoma area to a deep exploration campaign for Simpson production and production in the Pennsylvanian series on the south flank of the Arbuckle Mountains.

Jan 1, 1936

By H. C. Otis

DURING the past year or two considerable time and money have been spent in developing equipment for tubing large-volume high-pressure oil and gas wells without loss of production. That the efforts have met with success is proved by the fact that any properly cased well, regardless of its production or regardless of its rock pressure or working pressure, can now be safely tubed with no appreciable loss of production, provided experienced crews handle the new equipment. It is conceded that a far better gas-oil ratio can be secured by flowing a well through tubing of a proper diameter-the diameter of the tubing depending, of course, upon the volume of fluid and gas and the depth of the well-than by the more usual method of installing a choke at the mouth of the well. Where possible it is becoming the practice to bring wells in through tubing, though in the majority of instances this is not feasible. In many instances it has developed, after a well has been brought in through tubing, that the tubing installed is either too large or too small for the most efficient operation or that the well had not been drilled deep enough. The equipment described in this paper, in the hands of experienced men, permits the tubing of these wells after they have been brought in, with the size of tubing then determined by actual observation to be best suited for each particular well, and with no danger of the well getting out of control, of catching fire, of drilling itself deeper, or of any loss of production. The deeper the flowing production with the consequent future higher lifting costs, the more essential it is that the size of tubing used be such as to give the best possible gas-oil ratio. The ability to bring in these deep wells through the casing and then, immediately after their completion, regardless of volume or pressure, to tube them with the size of tubing that permits the most efficient use of the gas present will doubtless save many dollars.

Jan 1, 1929

By Rossier W. Raymond

John Birkinbine was born Nov. 16, 1844, at Reading, Pa., the eldest son of H. P. M. Birkinbine, widely known as a hydraulic engineer. The family removed subsequently to Philadelphia, where, as a young man he established with his father the office now, continued by his sons, after more than 60 years. His education was received at public schools, the Friends&apos; High School in Philadelphia, the Hill School at Pottstown, Pa., and the Polytechnic College of Pennsylvania, where his studies were interrupted in 1863-4 by service in the Union Army, which included participation in the battles at and around Gettysburg. Later, he devoted two years to work in a machine shop; and subsequently he became associated with the late P. L. Weimer, under the firm name of Weimer & Birkinbine, operating the Weimer Machine Works at Lebanon, Pa. Much of his work was in mining, metallurgy, and blast-furnace construction. As manager for the South Mountain Mining & Iron Co. he carried on experiments with various fuels for iron-ore smelting while maintaining the furnace in constant operation. The carefully recorded results obtained were widely published, and are referred to in text-books by other metallurgists as most complete. From his Philidelphia office he was sent to nearly every State, and to Canada and Mexico, for examinations, reports, constructions or im-provements in iron-ore mines, blast furnaces, iron works, water supplies, hydraulic development, irrigation projects, etc., and his engineering knowledge was requisitioned by several Eukopean corporations. A number of business trips were made to Mexico, beginning with a visit to the Cerro de Mercado at Durango,,before railroads were established in that. portion of Mexico, to make a critical examination and report on this "Iron Mountain." Later visits covered other localities and engineering problems, familiarizing him with the major part of the iron industry in Mexico. The late disturbed political conditions in that Republic have retarded the probable enlargement, modernization, and improvement of much of the iron and steel industry of Mexico, upon which he investigated and . reported for various capitalists on both continents. One interesting subject included in these reports was a proposed electric furnace, to be operated by energy from water power.

Jan 1, 1916

By C. H. Jr. Herty

IRON oxide .(Fe0) plays an extremely important part in the manufacture of steel. In the open-hearth furnace and the Bessemer converter it is the chemically predominant compound and controls to a large extent both the operation of the furnaces and the composition and quality of their products. Almost all of the refining action is carried out through the medium of FeO, which oxidizes carbon, manganese, silicon, and phosphorus. At the end of any open-hearth or Bessemer heat the steel contains dissolved iron oxide, which must be wholly or partly eliminated. The type of deoxidation product depends on the amount of dissolved iron oxide and on the deoxidizer used. After the heat has been deoxidized and while it is being teemed, iron oxide diffuses from the ladle slag into the metal, causing losses of deoxidizer and increase in iron oxide content of the steel. It is generally believed that non-metallic inclusions are responsible for a great many failures of steel in service and for decreased yield of steel during rolling. The basis of most non-metallic inclusions is dissolved iron oxide. This investigation was undertaken in order to determine the amount of iron oxide that will dissolve in iron under various conditions. Steel-making slags are complex and it has been thought best to determine solubility under simple slags as a first step. The study is being continued under slags whose compositions approach those of operating. slags.

Jan 1, 1928

By Frank H. Armstrong

All the mining machinery of the Penn Iron Mining Co. has been operated by electric power for several years and when another shovel for stockpile loading was required the advantages of an electric shovel were naturally considered. After considerable study, serious objections suggested themselves the use of a shovel operated directly by electrical apparatus by reason of the complicated control, severe service on the motors and the heavy surges of current required from the line. It was finally decided to construct an electro-hydraulic shovel using water under pressure to perform all the necessary operations except that of propelling, for which a separate motor was best suited. A car body with boom, dipper handle and dipper of late design, but without any of the steam machinery, was purchased. A motor-driven centrifugal pump, a pressure tank, an air tank, a small air compressor and water cylinders with plungers, pistons and valves, were installed in place of the steam equipment. Fig. 1 shows this shovel under construction and Fig. 2 shows it as it was operated during the first year, the summer of 1914. The large tank at the back of the car, in Fig. 1, carried air under

Jan 1, 1916

By R. C. Buehl, J. P. Morris

ACTIVITY values for sulphur dissolved in liquid iron and slags as functions of composition and temperature are needed in applying thermodynamics to sulphur-control problems in iron- and &apos; steel-making. The purpose of this investigation was to determine the effect of carbon on the activity of sulphur in the metal phase. The method employed was the same as that used in an earlier investigation&apos; concerning the effect of silicon on sulphur activity in liquid iron. A study was made of the conditions of equilibrium in the reaction between hydrogen gas and sulphur dissolved in iron-carbon alloys. The chemical equation for this reaction can be written as follows: S (in liquid Fe-C alloy) + H2 (gas) = H2S (gas). It was found that the activity coefficient of sulphur in liquid iron increases as the carbon content increases. At 2.3 pct carbon and 1600 °C, the activity coefficient of sulphur is twice its value in carbon-free iron, and at carbon saturation it is more than six times as great. The effect of temperature on sulphur activity was found to be small. Previous work on the reaction between hydrogen gas and sulphur dissolved in liquid iron has been reported by several investigators2,³,4 but only recently have studies been made of the effect of alloying elements. Silicon1 is known to have a pronounced influence on the activity of sulphur in iron, its effect being similar to that shown by carbon as described in the present report. Kitchener, Bockris, and Liber-man5 recently have published a preliminary report of their work on the effect of carbon on sulphur activity in iron. Their experiments were made at 1570°C and carbon saturation in the melt. Under these conditions they found that the activity coefficient of sulphur was approximately doubled by the presence of carbon. This is a much smaller effect than that found in the present work. Experimental Method: The apparatus and procedure were essentially the same as those used in the earlier investigation of the effect of silicon on sulphur activity.&apos; Briefly, the method was as follows: A molten iron-carbon alloy was brought to equilibrium at constant temperature with a mixture of H2 and H2S of constant composition by bubbling the gas through the metal. Samples of the melt were

Jan 1, 1951

By Thomas A. Edison, John Birkinbine

The Transactions already contain many valuable papers on the subject of ore-concentration, but with reference more to the treatment of other ores than those of iron. In this country much money, labor and thought have been devoted to the enrichment of iron-ores by roasting to drive off sulphur and carbonic acid, eliminate water, or make the ore more friable, and by washing and screening to remove the clay and sand from earthy ores. In concentrating magnetites and hematites more has been done than is generally believed; but, unfortunately, the results up to the present time have not been encouraging. On the contrary, so many attempts have proved unsatisfactory that any system of concentration is now unjustly looked upon with doubt, and the problem presented to individual mines must therefore be approached with caution. For many years the magnetites of the Adirondack region of New York State have been roasted, reduced to proper size by means of gang-stamps, and jigged on screens in water. Latterly plunger-jigs and rotary-jigs have been introduced, and in some places crushers and rolls have taken the place of stamps. In one instance in that region a plant for reducing the ore by crushers and rolls and separating it by magnetism was put up to treat a titaniferous ore; but, the titanium occurring as ilmenite, the result was unsatisfactory, and the plant is now being reconstructed at another mine, where apatite and silica are to be separated from the magnetite. A large concentrating works was erected at Negaunee, Michigan, in the Marquette region, Lake Superior, to enrich the leaner specular ores. This consisted of crushers, Cornish rolls and rotary-jigs. The results ohtained weye not satisfactory, and it has been abandoned. Another plan to treat the lean magnetites from a large dump-pile at Republic, Michigan, by means of pulverizers and water-jigs also

Jan 1, 1889