Search Documents

By S. Yukawa, M. J. Sinott

The low solubility of bismuth in copper and its segregation at copper grain boundaries with resulting embrittlement is well known.1-3 The heterogeneous diffusion of liquid bismuth into polycrystalline copper has also been studied.4 This work presents some further observations on these phenomena using high-resolution auto radiography to detect the presence of bismuth in copper polycrystalline and bicrystal specimens. The auto radiographs were made by the stripping film technique which produces an autoradiograph that is intact with specimen surface and can be examined simultaneously with the under-lying microstructure. The details of the technique have been described previously.3 In one series of experiments, high-purity copper was alloyed with 0.02 to 0.03 wt pct radioactive bismuth obtained from the Oak Ridge National Laboratory. Melting and casting was done under a

Jan 1, 1960

By D. J. Coolidge, H. L. Sheakley

This paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, pro- duced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is cornrnonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. I). Above the sand rock an overburden of Joachim limestone appears, which thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. Properties of the St. Peter Sand From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1948

By M. F. Fogler

An attempt to duplicate Rawdon and Mutchler's experiments showing a reversal of hardness with continued rolling gave negative results, indicating that the phenomenon is not general but depends, probably, on local conditions of rolling. IN A recent paper, Rawdon and Mutchler1 gave some exceptionally interesting results on the Brinell and scratch hardness of severely cold-worked metals. In their work, they found that, on continued cold rolling, the metal hardened up to a particular point and then reversed and became softer; this was true for both Brinell and scratch hardness values. The generally reported behavior2 of metals, with respect to Brinell tests on cold-worked material, is that the metals harden up to a certain point and then, on further cold rolling, no change in Brinell hardness occurs. Jeffries and Archer3 state that there is little difference between the scratch hardness of annealed and cold-worked metals; the work of Faust and Tammann4 also indicated no difference between-the hardness of annealed and cold-worked copper. Rawdon and Mutchler found, when they plotted the reduction ratio (initial thickness divided by thickness after rolling) against the hardness value for the cold-rolled material, that the hardness number increased up to a reduction ratio of about 3 and then decreased and became even smaller than that for the annealed metal. This behavior was reported for both scratch and Brinell hardness; Figs. 1 and 2 show their results for Brinell hardness on the metals for which they published data. This is an exceptionally interesting phenomenon, if it occurs under all conditions of rolling, and would have an important bearing on the practice of cold

Jan 1, 1925

By E. F. Koch, J. L. Walter

In a study of the structure and properties of tungsten wire used for lamp filaments, it became desirable to perform transmission electron microscopy on the wire in the annealed as well as in the drawn condition. Wire used for lamp filaments is generally drawn to diameters less than 0.010 in. which is too fine for the preparation of transmission samples from single wires. Thus, it is clear that some assembly of wires must be used to form a "wire sheet" similar to that used by Glenn and Duff.' Also, because recrystallized tungsten wire is brittle at room temperature, the "wire sheetJ' must be rigidly contained during any subsequent grinding and polishing operation. With these conditions in mind, a technique was devised for thinning tungsten wire of 0.001 to 0.010 in. diam for transmission electron microscopv. Sample Preparation. The commercially doped (218) tungsten filament wire was obtained from the Lamp

Jan 1, 1969

By M. C. Fuerstenau, D. N. Collins, R. B. Bhappu, D. N. Moir

D. N. Moir (Senior Scientific Officer, Warren Spring Laboratory, D.S.I.R. Stevenage) and D. N. Collins (Scientific Officer, Warren Spring Laboratory, D.S.I.R., Stevenage, England) — During work on the petroleum sulphonate flotation of beryl in 1959 at Harwell, and subsequently at Warren Spring Laboratory, effects similar to those mentioned by the authors were noticed. Brief details of some of this work were given to the 6th International Mineral Processing Congress at Cannes.' It is interesting to note that the authors experienced strong activation effects with Fe+++ ions on beryl when using petroleum sulphonate collectors. This phenomenon was of interest in our work when

Jan 1, 1963

By H. J. Ward

RUM Jungle uranium field lies in the subtropical portion of the Northern Territory on the Finniss River, East Branch. It takes its name from a railway siding about 2 ½ miles to the southwest and 52 miles from Darwin. The field can be reached from Darwin by a bituminized road. Monsoonal rains of the wet season, October to April, provide an annual rainfall of about 60 in. Vegetation is of the open forest type with denser tree growth along the watercourses and scattered throughout the area are isolated dense patches of jungle growth which are always found on ironstone cappings overlying limestones. The name, Rum Jungle, is thought to have been derived from this unusual occurrence of jungle growth. The wet season prevents the movement of motor vehicles and personnel. It is not until March, when the grass which ranges up to 15 ft in height is burned and the alluvial flats dry out, that field work can be undertaken.

Jan 12, 1954

By F. J. Tuck

The Hayden mill of the Ray Mines Division, Kennecott Copper Corporation, is now equipped with two 9 by 12-ft. rod mills having a daily capacity of 6000 tons of coarse-crushing plant product from the mine. These two mills crush a ¾-in. product to approximately 19 per cent on 14 mesh, with only one pass through the mills. Each rod mill has taken the place of four sets of 42-in. Garfield rolls with their attendant screens, and is making a product for the fine-grinding department comparable to that formerly made by rolls in closed circuit with screens. The rod mills are lined with wave-type liners of white iron, varying in thickness from 2 to 3 in. The shell and end liners last approximately 600 to 700 days. Manganese-steel lifter bars, 3? in. thick, are used, spaced about 11 in. apart, and they give a life of 350 to 450 days. Fig. 1 shows the general design and thickness of the wave-type liners and lifter bars; 1½-in. liner bolts are used to fasten the lifter bars to the shell. The shell liners are held in place by the tapered lifter bars. A ¾-in. wood backing is used between the shell and the liners. The rod-mill scoop has removable manganese-steel lips, which last 250 to 300 days. The scoop proper has shown some wear in spots, and these spots have been protected by rubber bolted over them. Water and milk of lime are added to the elevator feeding the mill, but not enough water to cause a pounding of the rods against the shell. Roughly, the water added amounts to 25 to 33 per cent of the ore. Additional water is added to the mill discharge to facilitate distribution to the classifier bowls in the fine-grinding department. Rods are charged to the mill once every four days, the mill being down about 20 min. for this purpose. Other delays are negligible, and usually are due to a loose liner bolt or possibly power trouble. However, these occasions are extremely rare. In charging the mill, a crane is used

Jan 1, 1939

By F. E Turton

THE town of Rancagua, at the junction of the state and Braden Copper Co. railroads, is located 82 km south of Santiago, the capital of Chile. From Rancagua 70 km to the east, situated in the Andes at an elevation of 7000 ft, is the town of Sewell, the location of a millsite. Two and one half km east of Sewell by underground railroad at an elevation of 7500 to 10,000 ft is the Teniente ore-body. The history of El Teniente dates from the eighteenth century, when according to legend a Spanish lieutenant, or teniente, a fugitive from justice, escaped to the Andes and camped at what afterwards became known as the Mineral El Teniente. This man reputedly discovered a vein of high grade copper ore. The first official records date from 1819, when some exploitation was begun, and continue until 1870. The orebody was large and of relatively low grade and was beyond the capabilities of the small groups attempting to operate it. No effort was made to erect a concentrator until William Braden became interested in the property. In 1901 Mr. Braden promoted the necessary capital for the first practical exploitation of the ore-body. Barton Sewell and E. W. Nash, both of the

Jan 1, 1953

By Marc Lemieux

Computer pit design techniques generally make use of models in which the deposit is represented by a regular array of data. Using a regular system, the number of data points required to represent the air, waste and mineralization in a large deposit become excessive. The number of blocks used to describe the deposit is dependent upon the block size. The quality of the pit wall slope design also is dependent upon the block size used and the method of defining the slope. The error associated with reserve calculations becomes greater with increasing block size. A deposit model consisting of variable sized air and mineralized blocks has been developed at the University of British Columbia and improved upon at Climax for pit design work. The method permits put- ting the entire model in core for rapid data processing. This permits the use of a versatile cone generation technique which allows close adherence to variable slope constraints in all directions. The conical shape is approximated by rectangles on each level which equal the area of the ideal conical intersection. The shape of the intersection may vary from approximately circular to elipsoidal. The approximate cone shape is controlled by the slope constraints applicable at the point of intersection on the bench. The overall modeling technique greatly assists the pit design engineer in developing a high quality pit design.

Jan 1, 1977

By N. W. Johnson

Mount Isa Mines Limited (Isamine) has process control computers in the major surface plants -- lead smelter, copper smelter, lead/zinc concentrator, and copper concentrator. HP computers are used to implement the more complex stabilizing control loops and control schemes aimed at optimizing plant performance. The choice of control strategies is discussed with particular reference to long-term performance in metallurgical plants. These control schemes must be understood by the process metallurgists who are responsible for the performance and initial fault finding. Major emphasis has been placed on the ability of the control systems to handle most of the common plant upset conditions as well as providing improved performance under normal operating conditions. To illustrate the approaches adopted, the lead/zinc concentrator crushing system and the process bag- house control system for lead smelter off-gas handling are reviewed in detail. The improvements in both of these areas resulting from control systems implementation are discussed.

Jan 1, 1984

By Jerome C. Motz

Primary Crushers The types, sizes and number of crushers employed in a complete reduction system will vary with such factors as the volume of ore to be processed, the size of the mine-run lump material, the hardness of the ore bearing rock and the size and dimension required for the final product. Basically, for primary crushing there are only three distinct types of crushing equipment. These are the Jaw crushers, Gyratory crushers and Impact crushers, and they each have their own distinctive operating characteristics. Jaw crushers operate by squeezing the rock between the fixed and the movable sides of a tapered cavity. Variations of pitch and swing have been tried, but most Blake-type machines have a crushing angle of about 27° between swing and stationary jaws. The principle of which Gyratory crushers work is very simple. If a Cone is mounted on the upper end of a vertical shaft and the top of the shaft is held .stationary while the lower end is rotated eccentrically, the Cone will also swing eccentrically. If the Cone is enclosed in a suitable housing, it will swing toward and away from the housing walls-as it rotates. If the done and the housing walls are sufficiently strong and heavy, anything caught between them will be crushed.

Jan 1, 1978

By Robert C. Freas, William H. Lane, David J. Krohn

Maysville, Kentucky, is the location of Dravo Lime company's new 9 070 mt(10,000 tons) per day limestone mine and 2 727 mt (3000 tons) per day calcination plant. This complex has been designed as a unit, and capitalizes on recent technological advances. Geologically the Dravo facility is.located on the eastern flank of the Cincinnati Arch, with the high calcium limestone being found at a depth of approximately 274 m (900 ft). A systems approach has been employed in designing and equipping the mine. This allows for maximum production while maintaining flexibility and versatility. All hydraulic drilling, large LHD equipment, and an extendable mine conveyor system are utilized in a five-part mining cycle. A modular concept modifies the room and pillar system to optimize ventilation. The limestone is calcined in three 5.18 x 61.87 m (17 x 203 ft) KVS rotary kilns with a design capacity of 909 mt (1000 tons) per day of lime per kiln. The kilns are coal fired and equipped with preheaters. Lime storage is provided by three 57 m (186 ft) high concrete silos with a combined capacity of 40 909 mt.

Jan 1, 1976

By H. S. Hanna, C. Rampacek

The problems and limitations encountered in the Physical beneficiation of the Appalachian Red Iron Ores are discussed. Two major problems are identified - the high phosphorus content and the fine dissemination or encapsulation of mineral impurities in the iron-bearing minerals. A process that combined extreme fine grinding techniques with magnetizing roasting or flotation-separation methods is suggested. By these methods, concentrates assaying 60-61 % Fe, exceeding the widely accepted upper limit of 56% Fe set for these ores, were produced with 75-90% iron recovery. Moreover, it was shown that the phosphorus content of these concentrates could be reduced from 0.25% to 0.03% phosphorus by acid leaching. A brief discussion on production costs based on current and future developments in iron ore processing is given.

Jan 1, 1983

Discussion of the paper of F. C. LANGENBERG and R. G. WEBBER, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 291 to 300. HENRY M. HOWE, Bedford Hills, N. Y.-The results here given are of great interest and are welcome as forming another rivet to increase the stability of our present theories of the constitution and properties of steel. The important discovery is that the hysteresis increases with the fineness of the structure, that is to say with the extent of contact between the particles of ferrite and cementite. All of the specimens except No. 4 consist of ferrite and cementite of different degrees of intimacy of admixture. If hysteresis represents something akin to surface friction, which retards the rotation of the ferrite on the application and release of the magnetizing force, then it is only natural that it should increase as it does with the intimacy of admixture, because it is at the surface of contact of a given particle of ferrite with the neighboring particles of cementite that this friction is to be expected, and of course the extent of surface must in¬crease with the intimacy of admixture. The somewhat greater hardness of specimen 4 than of the others may perhaps he referred to the principle discussed in my paper, Why Does Lag Increase with the Temperature from Which Cooling Starts?' The furnace-cooled specimens were cooled so slowly that the influence of the initial temperature of heating is effaced. But in the air-cooled specimens we have the suggestion that the high temperature, 1,000°, from which the cooling of No. 4 started has prevented the completion of the transformation, with the result that the metal is slightly harder than any of the others. The difference is not to be explained by difference in the fineness of structure, because the whole range of fineness from No. 1 to No. 6 is accompanied by no change in hardness, the only change being an appreciable increase of hardness following the air cooling from 1,000°.

Jan 5, 1915

By James Morgan

The convenience of mechanical arrangements for handling ingots, blooms, billets, bars, beams, etc., and feeding them to the rolls, is so universally recognized as to require no demonstration. In the rolling of heavy beams, such as are now coming into general use, such arrangements are practically essential, by reason of the difficulty and expense of the manual handling of the large masses of metal treated. I submit herewith the drawings of a rolling-mill feed-table, designed and patented by myself, which I think will be found simple in construction and operation, not likely to get . out of order, and efficient in performing the work for which it is intended. Fig. 1 is a sectional plan, taken on the line I I of Figs. 2 and 3. Fig. 2 is a vertical longitudinal section on the line II II of Figs. 1 and 3. Fig. 3 is a vertical cross-section on line III III of Figs. 1 and 2. As the details of the drawings are numbered throughout, and the same number always indicates the same part, I cannot more clearly describe the mechanism than by giving the following key to these numbers: Nos. 2 and 3 are the sets of rolls (here shown as three-high rolls, though that is not absolutely necessary). Nos. 4, 4 are the two feed-tables, one on each side of the rolls. The uide frames of the tables are made of parallel channel-bars. Nos. 6, 5 are the feed-rollers, journaled between the channel-bars and provided at their ends with beveled gear-wheels, 6, 6, which mesh with beveled pinions, 7, 7, on shafts, 8, 8, which latter are driven by elevated power-connections, to be mentioned presently. The tracks, 9, 9, on which the supporting-carriages are mounted,

Jan 1, 1891

By D. Krammer, E. S. Machlin

The effect of a brior high-temperature creep strain on the low-temperature ductility of commercially pure nickel has been evaluated. The low-temperature (-196°C) ductility decreases linearly with an increase in prior high-temperature (920°C) creep strain. The effect is experimentally correlated to the formation of inter crystalline cracks and voids during the prior high-temperature creep strain. The magnitude of the effect is also believed to be a function of the notch sensitivity of the material. SEVERAL mechanisms have been presented to explain the process of inter crystalline cracking in metals undergoing high-temperature creep. zenerl has suggested that grain boundary relaxation of shear stresses could build up high stresses at ob- stacles to grain boundary shear and thereby nucleate a crack. Chang and rant' have experimentally demonstrated that cracks do form at obstacles to grain boundary shear such as lines where three grains meet. The role of vacancies in the mechanism of high-temperature inter crystalline cracking has been explored by Machlt with the conclusion that the nu-cleation of voids by vacancy condensation is almost

Jan 1, 1960

By F. J. Zuiderweg, G. G. Bemer

Results of a study aimed at assessing kinetics and mechanisms of the batch agglomeration process in suspension are discussed. A recently developed light backscatter technique which enables the increase of average particle size from 1 to 5000 µm to be followed, was used to determine agglomeration kinetics. Growth curves and agglomerate size distributions were obtained in a stirred vessel for various model systems and operating conditions. Four distinct growth regimes were identified, i. e. the flocculation regime, the zero-growth regime, the fast growth regime, and the equilibrium regime. Further, it was observed that large differences in the occurrence and duration of these regimes resulted from small variations in parameters, such as size distribution of the initial particles and the binding-liquid to solid ratio. Mechanisms that determine the occurrence of the relevant regimes are discussed. The growth process was described in terms of population balance equations. In this way, the growth rate, the equilibrium agglomerate size distribution, and the evolution of the agglomerate size distribution were generated. The agreement with experimental results is satisfactory.

Jan 1, 1980

Some 30,000 people attended from 50 countries. Over 600 exhibitors brought with them a billion dollars of mining technology, ranging from tiny high-precision valves to giant off-highway trucks. Twenty-seven technical sessions with more than 100 papers covered the gamut of mining advancements. It was a grand display of industry vitality just to power the huge exhibit area required 22,000 kW of electricity each day, and support services for the exposition created more than 1000 daily jobs for local labor. Unquestionably, Las Vagas knew the miners were in town for the American Mining Congress' International Mlining Show.

Jan 11, 1978

By Alan K. Burton

The number of trucks required to perform a certain task is a function of the productive capability of one independent truck and the total tonnage required. Hourly productive capability of one truck is the product of trips, or cycles, per operating hour and effective payload. One cycle is made up of load, dump, and travel time, the sum of which comprises theoretical cycle time. This time is then derated by a productivity factor, giving an average effective cycle time which is used to calculate the number of cycles per hour. Rated payload is the truck's designed tonnage, while effective payload is the average amount that is actually carried. Manufacturers, particularly of the larger trucks, produce various body sizes designed to carry materials of different densities. However, it is not always possible to carry the rated payload because the material might be lighter than expected, a body of the required size cannot be produced, or because of spillage on particularly steep grades.

Jan 12, 1975

Single orders 2.5 c. Pamphlets 10. c. each in lots of three or more. Pamphlets 5 c. each in lots of fifty or more. These prices prevail for orders for pamphlet, of the same or different titles. The pamphlets listed on the following sheets are advance copies printed to facilitate discussion at the meetings of the Institute. They are offered for sale at the reduced prices given above as long as the supply, lasts. This list is published in the Bulletin in order that members may have the first opportunity to secure pamphlets, which sometimes are in such great demand that the supply is exhausted before the wants of members can be supplied. The following list includes only a fraction of the pamphlets that have been published by the Institute. Any other paper published by the Institute may be obtained for the price of $1, except those published in Volume XXXI, which are rare.

Jan 5, 1917