Search Documents

Surface mining of coal is widely condemned as a despoiler of the countryside and wastrel of land and natural resources. Yet the fact has been as widely ignored that the ingenuity of those engaged in developing the methods and equipment utilized in surface mining have made several hundred million tons of coal available for utilities and industry which could never have been mined by any other method. While doing this, the surface mining companies have recovered nearly 100% of the coal in the mining area instead of approximately 50% as is common in underground methods. Efficiency has been increasing constantly, thereby maintaining low cost to the customer. Mining has provided economic health in many areas by virtue of the direct payrolls and by the attraction of other industries to enjoy low cost, dependable fuel supplies. Surface mining of coal generally falls into two categories: contour mining, which is the result of mining in hilly or mountainous terrain where the hillside or slope limits the width of the area which can be surface mined; and area mining, which results from the surface of the land being approximately parallel with the coal seam so that a wide area may be mined in a succession of pits or open cuts.

Jan 10, 1972

By S. M. Brisbane

The life of refractory linings in rotary cement kilns can be shortened by uneven or inadequate support of the kiln and its shell and by variations in the conditions of operation. Alteration of these factors may, according to their nature, bring about mechanical deterioration of the lining or promote chemical attack. Chemical attack has been described elsewhere. The distortion of cement kilns has been discussed in a general manner by Rochow, who indicates the amount of distortion which may occur in an unlined shell, and by Rosenblad; who states that the deformations of the shell are greatest above the trunnions. The present article indicates the extent of the distortion of a kiln to an oval shape in certain selected positions and the deviation from a straight line of the kiln along its length between two supports. The cement kiln is a long, hollow, rotating cylinder consisting of steel plates which may be either welded or riveted together. This shell is supported on tires, frequently 60 ft apart, which roll on trunnions. The large mass of the kiln causes distortion of its cross-section; it becomes slightly oval, i.e., diameters lengthen as they become horizontal and shorten as they become vertical. There is also a tendency for the shell to bow between supporting tires; this bowing may be upwards or downwards depending on the position of the weight forces and the supports. The extent of the deviations from the ideal kiln shape was investigated.

Feb 1, 1956

Beyond the industrial suburbs of Melbourne to the southeast are brown coal deposits just under the fertile soil of the Latrobe Valley. These deposits rank as one of the wonders of the world. The manner in which this resource is put to use is one of the great engineering accomplishments of our time and also a prime example of Australian elan. The brown coal, with over 60% water content, occurs in beds from 200 to 400 ft thick, under 50 ft of cover. Fifty thousand tons of coal per day move in a nearly continuous stream from mining face to boilers. The power plants supply two thirds of the State of Victoria's requirements, about 800 megawatts. Surge capacity between mine and power plant is sufficient for 12 hr steaming time! Victorian brown coals have been known since the middle of the 19th century. However, it took a strike of bituminous coal miners in 1915 to bring brown coal permanently into the picture as a fuel for power generation. In Australia, power generation is a State function. The great development of brown coals has been under the State Electricity Commission of Victoria.

Jan 10, 1964

By B. H. Sage

VARIATIONS in the composition of the liquid phase of natural reservoirs which are continuous through significant ranges in elevation have been noted by petroleum technologists. In general, there is a greater gas-oil ratio and the gravity of the oil is higher in production from the upper parts of the formation. In the present paper the possible changes in composition with elevation which would result from the attainment of thermodynamic equilibrium in a uniform gravitational field have been evaluated for a naturally occurring hydrocarbon liquid, a binary hydro-carbon liquid phase and a binary hydrocarbon gas. The results indicate a progressive decrease in the mole fraction of the components from methane through the butanes with increasing depth, accompanied by a corresponding increase in the amount of the heavier components making up the system. The magnitude of these variations is perhaps insufficient to explain completely the variations in the properties of the liquid phase that are encountered at various elevations within a particular producing horizon. However, the changes are significant and the treatment presents an example of the application of thermodynamic data to the evaluation of the properties of hydrocarbon fluids under the conditions approaching those encountered in natural reservoirs.

Jan 1, 1938

By K. Fallenius

Since 1970 a new series of pneumo-mechanical flotation machines has been developed by Outokumpu Oy. The cells have a completely new type of mechanism based on a recently-developed theory of conditions necessary for dispersion of large amounts of air. The mechanism was developed in 3 cu m cells and scaled to 16 cu m cells. Rotor and stator description, scale-up theory, and practical experience with the 16 cu m cell are presented.

Jan 1, 1976

By B. G. Langston, R. D. MacDonald, F. M. Stephens

WITH the development of uranium ores that contain substantial amounts of acid-consuming compounds, the alkaline leach has become an attractive method for extraction. Considerable work has been done on both atmospheric and pressure-leaching with aqueous solutions of sodium carbonate and sodium bicarbonate as the lixiviants.1,2,3 For the treatment of uranium-bearing limestones and other high-lime (CaO) ores, the sodium carbonate leach has proven attractive because it avoids the high reagent consumption incurred by the reaction of sulfuric acid with lime. In addition, the corrosion problems with sodium carbonate are negligible as compared with those encountered in the acid-leach system. The sodium carbonate leach, however, does not yield as high an extraction of the uranium as the acid leach and is not attractive for economic reasons when treating ores that are high in sulfates or sulfides.

Jan 9, 1957

By Duane N. Goens, Clifford R. Porter

A 91 kg/h (200 lb per hr) pilot plant was constructed according to "Magnex" design. A non-compliance eastern coal which would generate more than 0.85 kg of S02 per GJ (2.0 lb of SO2 per million Btu.) upon burning was brought into compliance less than 0.52 kg of SO2 per GJ (1.2 lb SO2 per million Btu) during continuous operation of the pilot plant. Approximately 85% of the pyritic sulfur was removed while recovering 90% of the Btu of the feed coal. Pilot plant operation is summarized and preliminary economics presented. Present status of the Magnex design program is reviewed.

Jan 2, 1979

The second special war meeting of the New York Section was held on Thursday evening, Aug. 23,-preceded by is an informal dime The topic for discussion -was the supply of sulphur and pyrite, the raw materials for the manufacture of one of the most important of till war materials-sulphuric acid. The first speaker was William Young Westervelt, the Institute's representative on the War Minerals Committee. Before taking up the subject of the evening, Mr. Westervelt briefly described the organization and plan of operation of the War Minerals Committee.

Jan 10, 1917

By Jon Kogut

This paper describes three programs, currently in use within MSHA, for graphic analysis of accident frequency data. The first program, TREND, plots confidence bands for curved trends in data compiled over a period of time. In addition to detecting statistically significant upward or downward trends, the program can be used to determine whether an observation at a particular time deviates significantly from the historical pattern. The second program, POIPORP, plots interval estimates for the risk of accident in each of several environments, given an observed number of incidents and exposure time at each environment. POIPORP is designed to quantify the uncertainty implicit in incidence rates based on limited information and to facilitate statistically valid comparisons among the rates. The third program, CINDY, plots dynamically adaptive control charts for accident or injury experience at a given location. These charts are used to detect statistically significant departures from a changing standard or a previously established trend. All three programs are written in FORTRAN IV, utilizing DISSPLA and IMSL. They exemplify forms of statistical analysis that would not be practical without a computer. Use of the programs is illustrated with applications to coal mine fatality and injury experience.

Jan 1, 1983

By Robert A. Cummings, Francis S. Kendorski

The behavior of the rock mass during block caving affects the production of the mine and dictates the loads and deformations placed on required drifts. Traditionally, the drifts used are massively reinforced and buttressed against very high and erratic mining- induced abutment loads or swell muck loads, resulting from undercut- ting. Extensive field investigations in numerous block caving mines in the porphyry intrusive environment, coupled with models developed for tunneling and longwall coal mining, have allowed the development of a unified hypothesis for ore bodies of various degrees of competence. In general, the hypothesis incorporates several sequential steps in the driftlrock mass deformation history, each with characteristic magnitudes, duration, and areal extents depending on ore body competence. 1. Prior to initiating caving, but subsequent to drift development, the rock mass and drift are in a state of near-equilibrium. Zones of stress concentration have stabilized, as for a tunnel. 2. For a newly undercut panel, the rock mass and drifts directly beneath the undercut respond by dilating towards the void created, and undergo a release of compressive strain that manifests itself as tensile failures. 3. For adjacent areas, the rock mass is compressed as the load is shed from the undercut level.

Jan 1, 1983

Jan 11, 1950

By R. Neilson Clark

The discovery of a thin pay streak, yielding carbonates of copper; native silver, and perhaps chloride of silver, was made on the 9th of April, 1874, within the trachytic belt which forms part of the Sierra Mojada. The discoverer named it the Humboldt Mine. On the 2d of May, 1874, another discovery was made, in a northwest direction from the Humboldt, at about five hundred feet distant, this was named the Pocahontas Mine. After some exploration these two discoveries were proven to be on the same vein. To the southeast of the Humboldt a claim had already been taken up, called the Virginia; and to the northwest of the Pocahontas, one called the Southeast Leviathan. On these' last two this same vein has been found and worked. This paper will therefore treat of the Humboldt-Pocahontas vein, as worked on these four claims, to wit: beginning at the northwest, the Southeast Leviathan, the Pocahontas, the Humboldt, and the Virginia claims. Since the spring of 1874, there has been sunk on this vein a total of twenty-seven hundred and fourteen feet of

Jan 1, 1879

By Wayne L. Dowdey

With proud humility and keen anticipation, I accepted the office of President of the Institute one year ago, and it is with a great deal of pride in you-our membership that I make this report. You are the reason for a productive and prosperous year for AIME. Superior, good or satisfactory results were experienced in 1978 from almost everything we did as a leading engineering technical society. I recognize and pay tribute to the WAAIME organization. Their work is vital to our efforts, and their programs have proven effective. WAAIME can depend upon our continuing support.

Jan 6, 1979

By H. L. Sheakley, D. J. Coolidge

This paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, pro- duced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is cornrnonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. I). Above the sand rock an overburden of Joachim limestone appears, which thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. Properties of the St. Peter Sand From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1948

THE award from the fund established by Mrs. John-son, in memory of her husband, J. E. Johnson, Jr., to be given to some promising engineer, not over 40 years of age, because of meritorious research, inven-tion or contribution to the professional literature of iron and steel along the lines of blast-furnace process, has been given, for, 1928, to P. H: Royster. Mr. Royster was born at Raleigh, N. C., in 1888. and graduated from the University of North Carolina, in 1907, taking his A.M. degree at, the same school in 1908. He then went to Harvard where he continued research work in physics. After engaging for a while in commercial research in the turbine department of the General Elec-tric Co. and with Cutting and Washington he joined the staff of the Bureau of. Mines in 1916 and was assigned to work on the physical chemistry of the blast-furnace process. He worked with A. L. Feild on slag viscosity and they jointly presented-to the Institute the. papers on "Temperature and Viscosity Relations in the Ter-nary System CaO-A12O3-SiO2" (TRANS. LVIII, 658) and "Slag Viscosity Tables for Blast-furnace Work" (TRANS. LVIII, 650). He also presented a paper on "Production of Ferromanganese in the Blast 'Furnace" .(TRANS. LXII, 18), and jointly with T. L. Joseph contributed a paper on "Effect of Coke Combustibility on Stock Descent in Blast Furnaces" (TRANS. LXX, 236), and another on "Pyrometry in Blast-furnace Work" which was included in the special pyrometry volume published in 1920. The titles of these works perhaps sufficiently indicate the part Mr. Royster has played in the notable research work on the blast-furnace process carried on by the Bureau of Mines, and for which the committee recommended him to the Board of Directors to receive the Johnson award.

Jan 2, 1928

By Herbert Dumont

Since 1947 Preussag AG Metal1 has used a process for fuming zinc- and lead-containing dump slags and residues from vertical retorts in a half-shaft furnace at their Hüttenwerk Harz at Oker. Contrary to the classic shaft furnace, only one side of the half-shaft furnace is fitted with tuyeres. The opposite side is a bricked slope. The upper shaft section is piped. There zinc vapor and combustion gases are burned by sucked-in air. Gases and fume enter a boiler located on the rear length of the furnace via a piped fire bridge. The gases are then cooled in an air preheater prior to dedusting in a bag filter. The furnace is charged with briquettes of metal-bearing materials, coal and pitch. The leaded zinc oxide fume is comparatively rich in both lead and zinc. The copper in the feed is recovered in low-copper matte. The slag can be discarded. The Oker plant comprises 13 furnaces of 2.9 to 4.9 m length in the tuyere area. Two other plants in Italy and Spain are processing zinc leach residues by this technique. Fuming of zinc-lead-oxide ores as well as partially roasted sulfide- zinc-lead-copper bulk concentrates will be possible.

Jan 1, 1970

By Monte J. Pool, Rudolph Speiser, George R. St. Pierre, William T. Ebihara

Standard free energies of formation of WO,, W O W20058 and WO3from oxygen and the lower oxide or tungsten have been determined in the tempel-ature range of 700° to 1220°C. A tentative W-O phase diagmm is presented based on the evidence that the oxide phases, "W18O49" and "W20058", are unstable at l~atm total pressure, below 585° and 485°C:, respectively. A HE need for a complete quantitative treatment of the phase equilibria of the W-O system has been establishedby metallurgists during the past few years. In an attempt to improve the endurance of tungsten exposed to oxidizing atmospheres at high temperatures, many research groups have studied the kinetics of tungsten oxidation. The reverse process, the reduction of the tungsten oxides to metal, has also been investigated to some extent. Regardless of the particular interest, metal to oxide or oxide to metal, a knowledge of the phase equilibria of the W-O system is required to properly interpret all of the kinetic observations. It should be possible to state the stable phases of the W-O system at any given values of the chemical potential of oxygen and the temperature.

Jan 1, 1962

By J. C. M. Li

This exploratory survey was undertaken to repeat some experiments- in which anomalous results were reported1 for bismuth and to measure the thermoelectric power of some bismuth alloys and inter-metallic compounds. sato1 reported that the thermoelectric power of bismuth depends on the temperature gradient. This seems rather unreasonable especially when the Benedicks effect' has not been detected. Even if the material is not homogeneous, the observed thermoelectric power can be represented by

Jan 1, 1959

YUGOSLAVIA is one of the smaller countries in Europe-about twice the size of Pennsylvania -but one of the richest nations in variety and quantity of minerals on the Continent. The country, just now beginning the pangs of a real industrial birth, has a mining history that goes back as far as the sixth century, B. C. Among others, the Romans exploited Yugoslavia's lead and zinc deposits, and there was intensive mining during the Middle Ages. But until now, the country's industrial development was such that it made no great demand on the mining industry for development or expansion. Conversations with Yugoslavian officials in New York give the impression that they are interested in two things. They need money and they need trained engineers to solve their mining problems. Yugoslavia appears to be attempting to attract both foreign money and foreign technical skill. They want financial aid in the form of loans. The U. S. Government has given aid to Yugoslavia in the shape of armaments, foodstuffs, and equipment. Recently, American banks have advanced funds.

Jan 5, 1954

By M. E. Grimes

Rio Algom Mines Ltd. owns eight uranium mines and mills in the Elliot Lake district of Ontario, seven of which were producing before 1960. At present only one mine is operating and meeting current contract requirements. Under present economic conditions, it is not feasible to mine ore of less than 2.0 lb per ton U3O8, although there are very large reserves below this grade, Rio Algom is interested in preconcentration for three possible applications: to extend ore reserves by permitting use of lower grade ore, to reduce costs on processing of present grade ore, and to reduce capital investment in expanding production to meet future production goals. Rio Algom has been investigating various applicable preconcentration processes since the early 1950s to date, on laboratory and pilot-plant scale. Methods investigated include gravity concentration by sink-float, high intensity wet magnetic separation, flotation of uranium, flotation of acid consumers, and a number of electronic sorting methods including radiometric, photometric, and conductimetric. No method tested has yet been satisfactory under Rio Algom's criteria of uranium recovery and cost, principally because uranium loss has been too high for a useful weight rejection. Metallurgical results of the preconcentration test work and the economic assessment therefrom are reviewed.

Jan 1, 1974