Search Documents

By Charles M. Cooley

With explosives representing over 10 pct of the cost of operating the entire company, the Maumee Collieries Co., Terre Haute, Ind., inaugurated a program to develop a low-cost blasting agent. Results of more than two years' work were announced on May 1 by Hugh B. Lee, president of the company. Utilizing a mixture of commercial-grade ammonium nitrate and carbon black packed in polyethylene bags, Maumee has been able to reduce blasting costs by 50 pct. The lower costs are brought about principally by elimination of high transportation charges on fixed explosives and use of low-cost material (commercial NH,NO, and carbon black). The Akremite blasting method incorporates a 20-lb cap-sensitive primer to detonate the stable explosive. Maumee now uses Akremite exclusively in its stripping operations producing more than 2 million tons of coal per year. The explosive is employed to break about 25 million cu yd of overburden that covers the coal

Jan 5, 1955

Jan 1, 1894

By Stanley Herold

A FEW notes on the occurrence and significance of mud volcanoes in Colombia may be of interest at the present time, owing to the renewed activity in geological exploration of, the coastal regions bordering the Caribbean Sea. The best-known volcanoes are found a few miles from the seacoast. One is situated to the south of Puerto Colombia; the second, to the east: of Cartagena near the village of Turbaco; and the third, near the village of Puerto Escondido south of the Sinu River. Others. are reported in more inaccessible localities. Usually they stand 2 1/2 or 3 ft. (0.762 or 0.914 m.) above the surrounding ground at the crater, though several craters from 10 to 20 ft. (3.04 to 6.09 m.,) apart will often build up an extensive mound at low gradient. The shallow mound may cover 1/2 or 3/4 acre (0.2 to 0.3 ha.) with an elevation of 12 or 15 ft. (3.65 or 4.57 m.) at the center. The craters are formed of hardened blue clay; the inside diameters vary from 14 to 24 in. (35.56 to 60.96 cm.). The rim is continuous, except on one side where there is usually a cut 3 or 4 in. deep, thus allowing an overflow. The craters are filled to the rim-cut- with a thick mixture of blue clay mud and water, which is kept in agitation by escaping gas. Fig. 1 shows the bubble in the act of bursting and Fig. 2 the appearance of the surface of the viscous fluid a second or so later. The frequency of the explosions is determined by the weight of the column of fluid in the neck of the volcano, consequently, such explosions are not synchronous in a group of craters. Ordinarily, there are two or three explosions in about 3' minutes. The supply of gas is small but steady and sufficient pressure must accumulate before the bubble can enter the column of fluid. The water is derived from the surface and enters the sedimentary strata not` far distant from the volcano. During long dry seasons, as the supply of water fails the volcano dries and geyser action ceases.

Jan 7, 1919

G. B. WATERHOUSE,* Buffalo, N. -Y. (written discussion?).-One of the most essential features of rail manufacture is the production of rails that will give good service and be free from failures. To this end rails are made to careful specifications and their manufacture is controlled by rigid inspection on the part of both the producing mill and the railroad or its representative, such as the Hunt special inspection referred to in the paper. Captain Hunt refers to the crescent-shape base failures and describes them as ruptures in the rail flanges extending from the outside inward toward the web. This is hardly correct and may be misleading. It has been shown, over and over again, that the base breaks originating in seams invariably start at the center of the rail base; and run longitudi-nally in varying lengths from 3 to 12 in. and sometimes longer. Most of them are from 5 to 8 in. long and then curve outward to the edge of the flange. The split at the center of the base may exist for an indefinite time and not be discovered until the break shows on top of the flange or the piece of flange breaks off. The. stresses that cause the break are explained in two ways: (1) by the eccentric bearing of the rail base, that is taking contact at one side or edge and bringing excessive strain at the center of the base which starts fracture in any seam that may he present at that point; (2) the split may be due to cross strain in the base where this member is thrown into. compression, as happens where a pair of trucks are on opposite sides of the cross tie or rail-base hearing, and the head is put in tension. A careful study of "split base breaks" shows that fully 95 per cent. occur on the tie bearing, which is further evidence that the above de-scribed causes for the initial break are probably correct. These split base breaks are almost invariably progressive, but always start at the center of the rail-base running longitudinally.

Jan 12, 1919

By G. Herget, O. Garg

Trends will continue towards more automated, and sometimes larger mining and haulage equipment to reduce pit development and haulage costs. To save labour costs, larger capitalization of open pits is required and pit design and stripping ratios have to be firmed up at a very early stage of mine planning. Bench failures will assume a greater importance with larger equipment and at present we have only a limited capability of predicting stable slopes in complex structural geological settings. Deep open pits will pose particular problems in regard to high toe and floor stresses. This will require the development of more efficient systems for rock mass exploration and an improvement of our predictive capability in regard to pit slope stability and appropriate management of ground- water and materials. To meet the challenge, we have to improve: a) Analytical tools to assess slope stability in structurally complex settings as found in large open pits; b) Core orientation methods during diamond drilling operations; c) Geophysical logging methods to obtain geotechnical and structural geological information for large volumes of rock; and d) Geotechnical data handling systems to define mechanical properties

Jan 1, 1983

By William Plank

In practically all rock-excavation problems there is need for a careful study of the rock structure, its fault, cleavage or bedding planes, and even the texture of the rock itself. These studies should form the bases upon which an excavation method is selected and they should be carefully considered in predicting the amount and extent of the excavation. The need for such studies was forcibly illustrated in the problems involved in a cut made in 1929, along and underneath a 200-ft. high rock projection for a State-highway near the City of Easton, Pennsylvania. The rock mass was badly faulted and also contained a number of cleavage planes at approximately right angles to the fault planes. Much of this structure was visible and could have been studied and analyzed before' the work was begun. The State had rigid specifications as to finished grade and slope of cut, which apparently were made without reference to the geologic structure. The contractor complied with the specifications, under the close inspection of the State engineers. A tunnel blast was, placed in the base of the cliff, with the result that 65 per cent more rock was broken than was intended by the specifications. About four years after the blast, the writers of this paper studied the circumstances surrounding the operation, to determine the cause of this excess excavation.

Jan 1, 1935

By W. C. McBee, B. W. Jong, T. A. Sullivan

A sulfur concrete technology has been developed by the US Bureau of Mines, where chemically modified sulfur is used with suitable mineral aggregates to produce construction materials that are resistant to corrosion by acids and salts. This report presents a summary of the basic technology and results of testing the materials under actual operating conditions in 50 corrosive environments in 40 commercial plants. After four years of testing, there was essentially no evidence of material degradation or loss of strength. Regular concrete materials were attacked and, in some cases, completely destroyed under the same conditions. Testing is continuing to establish ultimate longevity and durability of the sulfur concretes. The materials are finding widespread applications in metallurgical, chemical, and fertilizer processing plants.

Jan 1, 1986

By W. H. Smith

IN the course of an investigation on chromium containing minor amounts of alloying elements, the information herein has been obtained on the crys-tallographic orientations resulting from arc melting, rolling, and annealing. The chromium used in this investigation was electrolytic flake obtained from the Electro Metallurgical Co. This material was heated for 20 hr at 1600°C in hydrogen with a dew point of about — 100°C. The oxygen and nitrogen content of the chromium after this treatment was 0.0003 pct 0 and 0.005 pct N. Five pounds of this chromium were arc melted in a water-cooled copper crucible. After arc melting, the oxygen and nitrogen contents were 0.002 and 0.025 pet, respectively. A section of this ingot is shown in Fig. 1. By means of a back-reflection Laue technique, the crystal habit of the cast ingot was determined. As expected, it was found that the [loo] was approximately the axis of the columnar grains. In this respect, chromium behaves like other body-centered-cubic metals in that a cubic axis is normal to the cold surface of the mold. A slab cut from this ingot was rolled at 600°C as follows: four 30 pct reductions were made with intermediate anneals at 1200°C for 15 min. Rolling was done with the [loo] of the columnar grains in the rolling direction. Following the final anneal, an 80 pct reduction was taken at 600 °C. The final sheet thickness was ten mils. By polishing and etching, the thickness was reduced to four mils and the grain orientation determined by the transmission Laue method using molybdenum radiation with a zirconium filter. Fig. 2 is the (110) pole figure for this material with the ideal (100) [011] and (111) [112] orientations indicated. The orientation is typical of most cold rolled body-centered-cubic metals having the [llO] of the grains approximately in the rolling direction and the (100) planes approximately in the plane of the rolled sheet. There is also evidence of some 10) [1 orientation. The grain orientation of sheet rolled 40 and 80 pct in the same direction as before at 600°C followed by recrystallization at 12000 C for 15 min was determined by a back-reflection Laue technique. A random texture was found in both cases. This 1200°C 15 min anneal was found to give complete recrystallization and some grain growth.

Jan 1, 1956

SIDNEY ROLLE, Chrome, N. J.-I should like to ask if Mr. Bach does not think it rather harmful to let the amen depend entirely on the company, whether it would not be a good plan to let the men aid a little in the support of these organizations? Also whether he has had any experience with utilizing the Y. M. C. A. in this connection. E. E. BACH, Ellsworth, Pa.-That question is always raised whenever there is discussion upon this subject. So far as we are concerned that would not help a bit; our people do not have that feeling, because .we have a company which these men recognize has a corps of very sympathetic officials in every way. I remember the assistant general manager lived out in one of these mining towns for a while. His difficulty was that every man, no matter what, who or where he was, if he had, or thought lie had, a, complaint, had the right of way to his office, and didn't have to stop at all. That is the spirit that predominates all through it. This is also the spirit of the mine foremen, two of whom were trained in our own night school, and it is the spirit of the fire boss and the general spirit of the people. They do not feel that we are trying to feed them with a spoon. As to the Y. M. C. A., we feel that it would be impracticable for us. R H. VAIL, New York, N. Y.-It would be very interesting if Mr. Bach would tell a little more about the control of the dispensing of intoxicants. There are many communities where the state intends to do that but does not succeed very well, and as Mr. Bach has spoken of the speakeasies on the environment of these towns, it would he well to know more about the problem of eliminating those.

Jan 4, 1918

By Ellis Clark

DURING the winter of 1877-78 the Glendon Iron Company, by the advice of the superintendent, Mr. Frank Firmstone, decided to make the experiment of exploding a heavy blast of gunpowder in their limestone quarry at Cedar Hill, Palmer Township, Northampton County, Pennsylvania. The amount of limestone used in the five furnaces of the company is about 60,000 tons per annum, and it was thought that with successful results; this entire amount or more would be thrown down at a single operation, disintegrating the mass to a greater or less extent, and obviating the necessity of blasting and boring the rock from the face of the cliff, both of which operations are slow, and therefore, costly. The rock at the quarry is Auroral limestone, or No. 2 of the old Survey. No fossils have ever been found in the quarry, nor in the immediate vicinity. The nature of the rock varies considerably in

Jan 1, 1879

By James W. Burns

Thin, heavily doped n-type layers of GaSb have been grown on p-type GaSb substrates. Techniques have been developed for the growth of the n-type layers from a tellurium-doped gallium-rich solution. The solution used consists of 95 at. pct Ga and 5 at. pct Sb. The process consists of immersing the p-type wafer in the solution at a temperature slightly above the liquidus temperature, holding briefly to permit dissolution of the substrate surface, then decreasing the temperature to a value slightly below the liquidus to obtain 1 HE resistivity of n-type GaSb varies linearly with applied hydrostatic pressure, while the resistivity of p-type GaSb is insensitive to such pressure.1,2 The growth. Growth from a solution of GaSb in tin will also be described. In either case the substrate is clamped to a shelf at one end of a graphite boat, and immersion of the wafer and subsequent decanting of the solution is accomplished simply by tilting the furnace. The process is useful for the formation of p-n junctions in III-V compounds and has the advantage that the problems normally associated with diffusion of Group VI elements are not present. Layers up to 4.0 mils in thickness have been grown by the process. material therefore should be useful in a hydrostatic pressure-sensing device. A practical hydrostatic pressure sensor, however, requires the fabrication of GaSb sensing elements of several hundred ohms resistance. Attempts were made to prepare such elements by diffusion, taking advantage of the high sheet resistance of the thin diffused layers and depending upon the p-n junction to provide isolation from the base layer. Additionally, thin layers of conductivity type opposite from that of the base layer were pre-

Jan 1, 1969

By Ellis Clark

During the winter of 1877-78 the Glendon Iron Company, by the advice of the superintendent, Mr. Frank Firmstone, decided to make the experiment of exploding a heavy blast of gunpowder in their limestone quarry at Cedar Hill, Palmer Township, Northampton County, Pennsylvania. The amount of limestone used in the five furnaces of the company is about 60,000 tons per annum, and it was thought that with successful results? this entire amount or more would be thrown down at a single operation, disintegrating the mass to a greater or less extent, and obviating the necessity of blasting and boring the rock from the face of the cliff, both of which operations are slow, and therefore, costly. The rock at the quarry is Auroral limestoue, or No. 2 of the old Survey. No fossils have ever been found in the quarry, nor in the immediate vicinity. The nature of the rock varies considerably in

Jan 1, 1879

By C. M. Wayman, M. A. Gedwill, C. J. Altstetter

Cobalt Whiskers were grown by the hydrogen reduction of CoBr,. The fcc = hcp martensitic trans-formation in these whiskers was studied using X-ray and metallographic techniques. Present theories of the fee + hcp martensitic transformation were ex-amined in the light of the present findings Experimental evidence for slip as a part of the transformation mechanism is presented. In the bulk form cobalt is known to undergo a martensitic transformation1 from an hcp to an fcc structure upon heating above about 430°C. Upon cooling, the reverse transformation starts at about 400°C, but does not go to completion except in single crystalline or coarse-grained samples, or upon plastic deformation. The transformation may be thought of as the shearing of close-packed atomic planes in such a way as to change the stacking sequence from ABCABC to ABABAB with a contraction normal to the shearing planes and an expansion in the planes,2 producing a c/a ratio slightly less than ideal. This restacking to give {0001) and (112) 11 (1010) can be accomplished by the passage of a shockfey partial dislocation over every other (111)f plane resulting in a theoretical shear of 19.47 deg. To date there has been no completely satisfactory explanation of how the partial dislocations are produced on the close-packed planes or propagated from plane to plane to give the correct stacking sequence. The object of the present research was to study some of the characteristics of the fcc to hcp transformation in geometrically simple single crystals. It was felt that whiskers of cobalt grown by halide reduction would be ideal specimens with which to study the transformation, because whiskers have the following desirable features: 1) are easily grown as fcc single crystals; 2) exhibit relatively simple geometries; 3) have comparatively low dislocation densities;

Jan 1, 1964

By Tom Learmont

The emergence of the dragline as the dominant stripping tool is described and reasons for this are noted. Brief comparisons are made with stripping shovels and wheel excavators. Representative output and machine availability figures for draglines are presented. The effect of changes in machine parameters such as boom length, swing power, and hoist power on machine productivity are discussed. An analysis of machine availability and the causes of machine downtime is made. Measures which are being taken to improve machine availability are discussed in detail. These include (1) improved methods of structural analysis, standardization of welded joints and welding methods to increase structural reliability and to develop more efficient structural designs, (2) standardization of gearing and mechanical componentry to permit the use of proven designs, (3) review of fairlead design and bucket hardware to improve rope life and reduce downtime, and (4) modifications to reduce maintenance time. The General Electric Data Logging system is described and consideration given to its use as a tool for improving productivity. Areas for future improvements in productivity are discussed.

Jan 1, 1976

By Jeremias K. Chitunda

Significant cost savings and improved ground stability are two initial indications from the current wet process shotcrete ground support program at the Lakeshore mine. The area of shotcrete for ground stability is not strange to the Lakeshore operation. Since the beginning of the project, various shotcrete techniques have constantly been experimented with, incorporating all the latest technological developments. Over the years, the use of shotcrete has been employed as a primary, temporary, or permanent support, singly or in combination with rockbolts and steel sets. The extent of shotcrete usage compared with steel sets and rockbolts has varied from time to time as dictated by the overall state of the art. In 1972, for example, the ratio of the linear drift footage supported with shotcrete to that supported with steel sets averaged 1.0. In 1973, that ratio was about 3.0. Overall, for the Lakeshore mine, there are about 8000 drift ft of shotcrete, 8000 drift ft of steel sets and timber, 750 drift ft of formed concrete, 21,000 drift ft of rockbolts, and 3700 drift ft of combined type support.

Jan 12, 1974

By Roland D. Parks

THERE are strong indications that chromium steel will one day hold the balance of power among all types of steel. Today, it is going to the forefront in military and civilian use. Stainless steel has received a tremendous impetus because of military demands. Chromium plays a primary, and possibly the most significant roll in the manufacture of stainless and other high temperature alloys. By any standard, chromium ranks among the most strategic of metals. Jet planes would still be on the drawing boards instead of flying in MIG Alley. Many of its more recent applications are the closely guarded secrets of the Pentagon and Government laboratories. Chromium has forged far ahead of the days when it merely decorated an automobile or made the American kitchen sparkle. The United States consumed one half of all chromium ores produced in the world during the past 50 years and 55 pct of those produced in the past decade. During those same periods, some 85 pct of world production of crude ores came from mines in the eastern hemisphere. Cuba is the only substantial supplier in the western hemisphere and most of the Cuban ore is suitable for use only in refractories. In presenting the strategic aspects of the chromium situation it will be helpful to give certain technical data as background without going beyond the detail needed for the survey. Use Pattern Ores containing chromium are consumed by the metallurgical, refractory, and chemical industries. In the United States, postwar consumption by these industries has been in the approximate proportions .of 47:37:16, respectively. In two industries, metal¬lurgical and chemical, the ores are first converted to intermediate products. . For metallurgical use, the ores are usually smelted in electric furnaces to ferrochromium, an

Jan 1, 1952

By I. N. Zavarine

Austenite is often defined as a solid solution of carbon or carbide in a nonmagnetic form of iron. Conversely, magnetic measurements are often used by investigators for the purpose of detecting the degree of austenite decomposition after an iron alloy has been subjected to certain thermal or mechanical treatments. Association of the magnetic state with the gamma-phase decomposition is often extended to the alloys of iron with elements other than carbon. Definition of austenite as a nonmagnetic solid solution cannot be accepted in the light of available information without certain reservations. The relation of magnetic transformations with the gamma-phase decomposition in the complex alloys of iron has never been rigorously proved. The present investigation deals primarily with the magnetic transformation that occurs in carbon steels during the quenching process. The work was further limited to a study of magnetic transformation in carbon steels quenched at such rates as are necessary to retain the product of austenite decomposition in a martensitic state. Peevious Work Considerable information has accumulated in the literature with respect to the magnetic transformation in alloys of iron, but nearly all of it relates to transformations under the conditions of equilibrium between the phases of the alloy. Earlier studies of Hopkinson,$(') Curie,(2) and Honda'~) are well known. Investigations of the magnetic

Jan 1, 1934

By R. A. Harrington, H. R. Nelson

The: structure of anodic films formed on aluminum and other metals under varied conditions is not well known despite the wide use of such films both as protective coatings and as the dielectric medium in electrolytic condensers. The present work was undertaken as a survey of the possibilities of electron diffraction in the investigation of anodic films, especially in comparing the properties of anodic films formed under different sets of conditions and subjected to various subsequent treatments. In addition, an effort has been made to compare surface films formed on aluminum by anodic treatment with surface films formed by heating, immersion in chemicals, etc. The elcctron diffraction method in many cases has been successfully applied to the study of thin surface films. Its principal advantage is that it can be used without removing the films from the base material upon which they have been formed. The low penetrating power of electrons, in the "reflection" diffraction method which has been used in this work, prevents the appearance of diffraction patterns from substances at depths greater than about 100 Angstrom units (lop6 cm.). Different investigations of the structure of anodic films have showll widely varying results, depending on the methods used in preparing the films. Apparently under some conditions these films are crystalline and under other conditions they are amorphous, and it has been difficult to say which type of structure will be found in any particular case. Schmid and Wassermann's1 X-ray diffraction patterns of eloxal‡ films show two broad, diffuse bands, which these investigators attribute to finely divided cubic y-Al2O3.§ Burgers, Claassen, and Zernicke³ obtained sharp X-ray

Jan 1, 1940

By John V. Beall

Given: One large, but dated open-pit copper mine and processing plants, down about one third in production capacity in decade because of declining ore grade. Solve for: Restoration of former peak capacity without further losses during period of reconstruction. That is the problem that Kennecott's Utah Cop- per Division began solving in 1963. Most of the work went to a task force of engineers, several of whom were plucked out of line jobs and assigned to the so-called "Expansion Project" for the duration. There was no doubt from the beginning that effective cooperation between Expansion Project engineers and operators was critical to success, and personnel was chosen accordingly. This foresight paid off. The Expansion Project is all but complete, and the Utah Copper Division is returning to its rated capacity of 300,000 tons per year of copper metal.

Jan 6, 1967

By R. A. Harrington, H. R. Nelson

The: structure of anodic films formed on aluminum and other metals under varied conditions is not well known despite the wide use of such films both as protective coatings and as the dielectric medium in electrolytic condensers. The present work was undertaken as a survey of the possibilities of electron diffraction in the investigation of anodic films, especially in comparing the properties of anodic films formed under different sets of conditions and subjected to various subsequent treatments. In addition, an effort has been made to compare surface films formed on aluminum by anodic treatment with surface films formed by heating, immersion in chemicals, etc. The elcctron diffraction method in many cases has been successfully applied to the study of thin surface films. Its principal advantage is that it can be used without removing the films from the base material upon which they have been formed. The low penetrating power of electrons, in the "reflection" diffraction method which has been used in this work, prevents the appearance of diffraction patterns from substances at depths greater than about 100 Angstrom units (lop6 cm.). Different investigations of the structure of anodic films have showll widely varying results, depending on the methods used in preparing the films. Apparently under some conditions these films are crystalline and under other conditions they are amorphous, and it has been difficult to say which type of structure will be found in any particular case. Schmid and Wassermann's1 X-ray diffraction patterns of eloxal‡ films show two broad, diffuse bands, which these investigators attribute to finely divided cubic y-Al2O3.§ Burgers, Claassen, and Zernicke³ obtained sharp X-ray

Jan 1, 1940