Search Documents

By A. R. Jr. Amos

LOG washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate com-pletely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5° to 10° and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1936

By M. B. Standing, D. L. Katz

Equilibrium data are reported on the composition and densities of coexisting vapor and liquid phases as a function of Pressure and temperature for four hydrocarbon systems prepared from crude oil and natural gas. The data were observed over a range of pressures from 1000 to 8220 Ib. per sq. in. and at temperatures ranging from 35' to 250°F. The compositions of the hydrocarbon systems were such that the critical temperatures of the mixtures were lower than the range of the investigation. Under these conditions, it is shown that the composition of the systems has a marked effect upon both the absolute value of the equilibrium constants and the change of the constants with pressure for the several components comprising the system. From weight-balance considerations, it has been possible to construct the partial phase diagram of a mixture of a 49.9" A.P.I. crude oil and natural gas having a gas-oil ratio of 3660 cu. ft. per barrel. Descriptions of the apparatus used, the analytical procedure, the material used, and the equilibrium measurements are included. A knowledge of the physical behavior of naturally occurring hydrocarbon mixtures is fundamental to the treatment of many problems in the production, transportation and rehing of petroleum. The recent discoveries of pools having formation pressures up to 7500 lb. per sq. in. and higher, and the development of full-scale equipment to operate at pressures of 5000 lb. per sq. in. or more have greatly increased the need for knowledge of the composition, temperature, pressure and density relationships of coexisting vapor and liquid hydrocarbon phases. The following paper presents the results of investigations upon 22 mixtures of natural gas and crude oil of known com~o~itio~ that had been brought to equilibrium under controlled conditions of temperature and pressure. Data are presented upon the densities and compositions of the coexisting vapor and liquid phases for four different systems containing hydrocarbon material having boiling points from minus 2 5S°F. to well over I000 F. The data were observed Over a pressure range from Iooo Ib. per Sq. in to 8220 lb. Per sq. in. and a temperature range from 35' to 2 50°F. The accepted method of computing the physical relationship between two coexisting phases of a hydrocarbon mixture is by use of the "equilibrium constant" K as proposed by Souders, Selheimer, and Brown. definition,

Jan 1, 1944

By M. B. Standing, D. L. Katz

Equilibrium data are reported on the composition and densities of coexisting vapor and liquid phases as a function of Pressure and temperature for four hydrocarbon systems prepared from crude oil and natural gas. The data were observed over a range of pressures from 1000 to 8220 Ib. per sq. in. and at temperatures ranging from 35' to 250°F. The compositions of the hydrocarbon systems were such that the critical temperatures of the mixtures were lower than the range of the investigation. Under these conditions, it is shown that the composition of the systems has a marked effect upon both the absolute value of the equilibrium constants and the change of the constants with pressure for the several components comprising the system. From weight-balance considerations, it has been possible to construct the partial phase diagram of a mixture of a 49.9" A.P.I. crude oil and natural gas having a gas-oil ratio of 3660 cu. ft. per barrel. Descriptions of the apparatus used, the analytical procedure, the material used, and the equilibrium measurements are included. A knowledge of the physical behavior of naturally occurring hydrocarbon mixtures is fundamental to the treatment of many problems in the production, transportation and rehing of petroleum. The recent discoveries of pools having formation pressures up to 7500 lb. per sq. in. and higher, and the development of full-scale equipment to operate at pressures of 5000 lb. per sq. in. or more have greatly increased the need for knowledge of the composition, temperature, pressure and density relationships of coexisting vapor and liquid hydrocarbon phases. The following paper presents the results of investigations upon 22 mixtures of natural gas and crude oil of known com~o~itio~ that had been brought to equilibrium under controlled conditions of temperature and pressure. Data are presented upon the densities and compositions of the coexisting vapor and liquid phases for four different systems containing hydrocarbon material having boiling points from minus 2 5S°F. to well over I000 F. The data were observed Over a pressure range from Iooo Ib. per Sq. in to 8220 lb. Per sq. in. and a temperature range from 35' to 2 50°F. The accepted method of computing the physical relationship between two coexisting phases of a hydrocarbon mixture is by use of the "equilibrium constant" K as proposed by Souders, Selheimer, and Brown. definition,

Jan 1, 1944

By A. R. Jr. Amos

LOG washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate com-pletely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5° to 10° and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1936

By G. Sachs, S. I. Liu

Introduction In a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24 ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in Fig I,$ the ductility (e~) retained after prestraining in tension by a certain amount (el) and measured in a subsequent tension test is represented by a straight line sloping down under 4s°. If a compression of the same magnitude as the first tension is inserted (€2 = — €1) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.~ As also shown in Fig I, the ductility in subsequent tensile tests decreased with com- pression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount el, subsequently straining in compression by an amount e2, and finally determining the retained &apos;ductility, e,, in a tensile test. Prestraining in tension is then represented by el > o and e2 = o. Prestraining in compression is given by e~ = o and e~ < o. Balanced cyclic straining is defined by the condition el > o and cz = — 61. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, el, and the compression strain, e2, within extreme limits; el varied between 0.06 and 0.28 and e2 between — 0.008 and —0.h approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date, The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the sub-

Jan 1, 1949

By Jacques B. Wertz

Detailed structural studies in southeast Arizona have successively revealed (1) the local attitudes of individual fractures (with lateral and/or vertical displacements), (2) the patterns exhibited by groups of fractures, and (3) the trends and directions shown by fracture groups or zones on a regional scale. The results of the studies have been twofold: First, domes were locally determined from these fracture arrangements, even where other criteria failed; and, second, fundamental breaks brought out the breadth of the Texas lineament in southeast Arizona as well as major northwest- and northeast-trending fracture zones. Coincidence of one or several domes with the major intersections of fundamental breaks can be centers of important mineralization, as in the instances of Bisbee, Ajo and Morenci. THE OVER-ALL STRUCTURE OF ARIZONA A northwest-southeast trending anticlinorium has been suggested as the structural setting of Arizona. Starting in Triassic and culminating in late Cretaceous times, this deformation resulted from stresses of considerable magnitude with varying ratios of com pres sional and uplifting forces. However, the series of parallel flexures could just as well have been caused by isostatic movements involving dilation under tension with only incidental compression, as later emphasized by dike filling and block faulting (Fig. 1). The anticlinorial deformation, which is also suggested by the fact that the Pre-cambrian rocks to the southwest are all concealed by sediments, could be somewhat reminiscent of the conditions that affected the classical swarm of parallel dikes of wager.&apos; ANALYSlS OF DATA As a first step in this analysis, all structural information obtained on such features as fractures and their relative displacements, faults, dikes, anticlines, synclines, and Precambrian and Laramide-Tertiary intrusives were plotted on maps along with structural trends inferred from aerial photographic mosaics. Next, the faults in southwest Arizona were classified according to time of occurrence and relative importance. The fault assemblages were then examined as to geometric or spatial arrangement and correlated with the occurrences of domes and existing Finally, the conjunction of fracture intersections and domes was analyzed and compared with locations of known ore deposits. Differentiation of Faults According to Time and Relative Importance: The faults encountered were grouped as follows: (1) Basin and Range faults, latest in time; (2) secondary faults; (3) primary faults; and (4) lineaments, earliest in time by inference. BASIN AND RANGE FAULTS- Generally concealed by alluvium, the Basin and Range faults are normal

Jan 1, 1969

By Pei-Yung Huang, Carle R. Hayward

IN order to understand more fully the actual state of copper lost in copper reverberatory slags, a systematic study on the various reactions between certain metallurgically important copper compounds and synthetic copper reverberatory slags was undertaken by the authors in the Massachusetts Institute of Technology from 1942 to 1945.1 This paper, being only a part of the work completed, is published first because it furnishes the first experimental evidence of the formation of copper ferrite from reactions between cuprous oxide and copper reverberatory slags. CHOICE OF SLAG COMPOSITION The choice of the composition of the synthetic reverberatory slags to be used was much deliberated. Commercial copper reverberatory slags, neglecting minor constituents, average:2.3 45 to 47 pct FeO; 38 to 42 pct Si02; 5 to 6 pct CaO; 5 to 6 pct A1203. Since the ternary system CaO-FeO-SiO2 has been much more thoroughly studied4 and is much simpler than the quaternary system CaO-FeO-Si02-A1203, it was decided to use calcium oxide only instead of calcium oxide and alumina in the synthesis of the slags. Fortunately the composition of the average copper reverberatory slag with calcium oxide substituted for alumina lies in the region of the phase diagram clarified by the investigators. A survey of the phase diagram (Fig I) suggested two compositions: (I) the com¬position near the invariant point S, which is made up of 46 pct ferrous oxide, 37 pct silica and 17 pct calcium oxide; (2) the composition near the invariant point K with 45.5 pct ferrous oxide, 43 pct silica and 11.5 pct calcium oxide. Composition S has the advantage that the percentages of ferrous oxide and of silica almost exactly coincide with those of the average reverberatory slags, and that of the lowest melting point (1093° ± 3°C) in the whole ternary system. The calcium oxide content, however, obviously is high. Since we have already substituted calcium oxide for alumina, and since calcium oxide is more basic than alumina, the resulting slag is decidedly too basic. Composition K has a slightly higher melting point (1105° ± 3°C) and a higher silica content, but this is preferred because the slag is saturated with respect to tridymite and thus should not corrode siliceous refractories. Besides, it is less basic than composition S. The final slag composition, therefore, was chosen to

Jan 1, 1947

By Leonard B. Gulbransen, John R. Lewis, W. Martin Fassell, J. Hugh Hamilton

T. E. Leontis (The Dow Chemical Co., Midland, Mich.)—This paper is of particular interest to me because of my own work with F. N. Rhines on the oxidation of magnesium and magnesium alloys a few years ago. The authors are to be complimented on their development of an accurate and reproducible technique for measuring ignition temperatures and on their comprehensive study of the many variables that affect the ignition temperature of magnesium. It is indeed gratifying to see that they have obtained a good correlation between ignition temperatures and the oxidation rates reported by us. The correlation is valid not only with composition within one alloy system but also between alloy systems; that is, alloying elements which effect the greatest increase in oxidation rate also produce the greatest decrease in ignition temperature. There are a few points upon which I would like to comment. In attempting to correlate ignition-temperature data, one must be sure that the same definition of this quantity is used by all investigators. It does not appear to me that such is the case in the authors&apos; comparison of their data with the theoretically calculated values of Eyring and Zwolinski. The equation derived by these investigators defines the ignition temperature, To, as the temperature at the gadoxide interface, whereas the present authors use the metal temperature as the criterion for ignition. The contradiction in the effect of oxide-scale thickness on ignition temperature between the predictions of the Eyring-Zwolinski equation and the observations reported in this paper indicate that some variable has not been taken into consideration. Could that be the geometry and size of the specimen? There is a marked difference in the type of specimen used in this investigation and that used in our work which formed the basis of Eyring and Zwol-inski&apos;s theoretical treatment. Another factor which plays an important role in ignition is the vapor pressure or the rate of vaporization. Combustion can safely be assumed to take place in the vapor phase by the reaction between vaporized magnesium and oxygen. Thus, a more accurate theoretical analysis may be made on the basis of the rate of vaporization which may be the controlling rate of the process. The effect of a large number of alloying elements on the ignition temperature has been reported in this paper, but beryllium was not included. Practical experience dictates that beryllium markedly decreases the burning tendency of magnesium. I was wondering if the authors plan to study the effect of beryllium in their future work. The authors predict that concentrations of sulphur dioxide in the furnace atmosphere greater than 5.8 pct would be expected to increase the ignition temperature to values still higher than those they measured. I would like to mention that large concentrations of sulphur dioxide markedly increase the rate of combustion of magnesium once ignition has started. Although it has been shown in the paper that the ignition temperature of magnesium in oxygen increases with increasing sulphur dioxide content up to about 1 to 2 pct, in practice relatively low-melting commercial cast alloys (AZ63A and AZ92A) are being continuously heat treated at temperatures just below the melting point in air containing 0.5 to 0.75 pct SO*. In regard to the change in color of the oxide scale observed on magnesium and magnesium alloys just prior to ignition, I would like to mention that in our work alloying elements were found to color the usually white magnesium oxide even though ignition did not occur. For example, the oxide formed on Mg-A1 alloys was gray, increasing in intensity with aluminum content in the alloy. Finally, I might suggest that the authors indicate their source of the value of 0.8 g per cc for the density of MgO as it is formed on magnesium upon oxidation at elevated temperatures. W. M. Fassell, Jr. (authors&apos; reply)—The comments by Dr. Leontis are very excellent ones and I will attempt to answer them in order. First, the problem of ignition of magnesium is a rather difficult one since many factors are involved. Concerning the comparison of the To in the Eyring-Zwolinski equation, eq 4, with the experimentally determined values, it will be noted that the calculated and experimental values of the ignition temperature in Table I are not self-consistent. In the case of the 1.78 pct A1-Mg alloy the calculated value is 49°C below the experimental value; for the 3.81 pct A1-Mg alloy, 122°C below the experimental value; for Mg with 5x10-&apos; cm film, 19°C above the experimental value; for Mg with 2x10-I cm film, 28 °C below the experimental value. Thus, if it were merely a matter of difference of location of temperature measurement the calculated ignition temperature would always be below the experimental value, the difference being due to the thermal gradient through the oxide film. The possibility of a thermal gradient in the magnesium metal must be considered. From Carslaw and Jaeger,&apos;Y t can be shown that the maximum temperature gradient that could exist between the oxide-metal interface and the center of the sample is of the order of O.Ol°C. The geometry and size of the specimen could certainly have some effect on the ignition temperature. The equation for ignition that has been proposed in reference 14 is of the following type containing terms to account for this and other factors: M dT AHv(T) =Cp--------------\-J(.T—TB) + ZAHl-M A dx where AH is the heat of reaction, v(T) is the velocity of the reaction at temperature, Cp is the heat capacity of sample, M is the mass of sample, A is the area of sample, t is time, J is the total coefficient of heat transfer outward from the reaction zone, TR is the temperature of the bath or furnace, and AH,, is the heat associated with any phase change involved. Prior to the instant of ignition, the vapor pressure of magnesium is of no special significance. After ignition, neither eq 4 nor the above equation is applicable. The actual combination of magnesium cannot safely be assumed to take place in the vapor phase. While experimental data is lacking to support a hypothesis that ignition does or does not occur in the vapor phase, some observation on the pressure ignition experiments may be of interest. At high oxygen pressures, once ignition has occurred, the reaction of magnesium with oxygen approaches near explosive violence, the entire sample being consumed in probably less than 1 sec. At atmospheric pressure it usually requires 15 to 20 sec. Thus it appears that the oxygen concentration becomes the rate determining factor. Further, if burning magnesium is observed through darkened glass (Lincoln Super-visibility Shade No. 12) the magnesium sample is very much hotter than the "smoke" and the outline of the sample is retained perfectly. No "flame" is visible above the metal. No work was done on Mg-Be alloys. We do, however, intend to study this problem in the near future.

Jan 1, 1952

By Gen-ichi Nakazawa, Masamichi Fujimori, Ichiro Doi

INTRODUCTION The major products of nickel industry in Japan are the electrolytic nickel (E-Ni), the ferro-nickel (Fe-Ni) and the nickel oxide sinter (NOS), totaling in production to 90 - 100 X 103 tons/year in terms of pure nickel content, and sharing approximately 20% for E-Ni, 10% or less for NOS, and the rest for Fe-Ni. The raw materials to be used for these products depend totally upon the imports from abroad; matte, the raw material used in the production of E-Ni, is from Australia and Indonesia; matte for the NOS is from Indonesia and New Caledonia; and garnierite, the raw material for Fe-Ni, is imported in bulk from New Caledonia, Indonesia and the Philippines. This report describes the acquisition of these raw materials, the production processes, trend of supply-demand, problem areas and the measures taken, and so forth, in connection with the nickel industry in Japan. ELECTROLYTIC NICKEL 1. History The nickel industry in Japan began in 1939 by the Sumitomo Metal Mining Co., Ltd. (SMM) with 150 tons E-Ni/month under the blast furnace smelting and the metal anode electrolysis. This was temporarily suspended after the end of last World War II, but resumed in 1952 with garnierite of New Caledonia as a raw material. Since then, the production capacity has been expanded incidentally to the increase of demand. However, since the smelting of garnierite contained about 2% nickel was very costly, the smelting process had been changed to smelt the briquettes of the mixture of garnierite and nickel sulfide concentrate imported from Canada and Australia. In 1975, this smelter was closed, and SMM&apos;s nickel refinery used matte from Western Mining Corp. (WMC) of Australia as a raw material. The refining process had been the metal anode one. The crude nickel oxide derived from roasting the high grade nickel matte had been melted and reduced with coke in the electric furnace and cast into anode. In 1970, a new refinery was constructed to produce 1,000 tons Ni/month under the matte anode process, and further, in 1976, the old refinery was converted into the matte anode process, thus resulting in the total production capacity of 1,690 tons Ni/ month today under the matte anode process. Shimura Kako Co., Ltd. began in 1951 to produce a little of E-Ni, and in 1955, they constructed a shaft furnace smelter with New Caledonian garnierite as a raw material to begin the E-Ni production under the matte anode process. Its monthly production reached 400 tons in 1957, but it discontinued its smeltering in 1963 to convert to the matte import from S. Le Nickel, WMC and INCO. In 1979, it changed the source of matte supply from the above to Soroako of Indonesia, discontinued the E-Ni production in 1979, and arranged for a total toll contract with Sumitomo. Meanwhile, SMM has developed a very distingished process for nickel-cobalt separation and refining by a solvent extraction method from nickel and cobalt mixed sulfide generated as a by-product in the nickel recovering process from laterite under the Nicaro process. Nippon Mining Co., Ltd. (NMC) also developed its own process. The plants under these processes were constructed in 1975, with the monthly production capacity of 230 tons of nickel and 130 tons of cobalt by SMM, and 300 tons of nickel and 110 tons of cobalt by NMC. SMM imports the raw material from the Marinduque Mining and Industrial Corp. of the Philippines, while NMC from Queensland Nickel Pty. Ltd. of Australia. 2. Production Status 2.1 Producers and materials Today, SMM holds the monthly E-Ni production capacity of 1,920 tons, of which 1,690 tons are from the matte anode process, and the remaining 230 tons are from the mixed sulfide as a raw material. NMC also uses the mixed sulfide as a raw material for a production of 300 tons/month. [ ] Most of SMM&apos;s raw material, nickel matte, is imported from WMC of Australia, partly using the Soroako matte from Indonesia. An example of material analysis is given in Table 1. Matte is a raw material for E-Ni and NOS, and the major sources of matte supply at present are Australian WMC and Indonesian Soroako, occupying ap-

Jan 1, 1982

By G. Bruggeman, K. G. Kreider

Grain boundary dij]usion coefficienls were measured in tungsten between 1400° and 2200° C and can be expressed by the equation sq cm per sec This activation energy confirms some eavlier estimates made .from tungsten sintering experiments. Grain boundary diffusion was found to occur in sub-bozrndavies having -misorientations of less than 10 deg. The actiuation energy for this subboundavy diffusion is equal to that for dijjusion in incoherent grain boundaries with in the limits of error. This is shown to be consistent with the dislocation model of Low-angle boundaries wheve diffusion occlcvs along- the dislocation &apos;YPipes" comprising -tile boundary. RECENT investigations of the sintering of tungsten powders all report activation energies which are considerably less than the activation energy for tungsten volume diffusion. Kothari&apos; reports a value of 100 * 5 kcal per mole, Hayden and Brophy&apos; obtained 90 kcal per mole, and Vasilos and smith3 found 110.7 kcal per mole from their sintering studies. Since most determinations of the activation energy for volume diffu-sion4-&apos; fall between 120 and 160 kcal per mole (the true value seems most likely to be nearer 150 kcal per mole), the conclusion is drawn that the mass transport leading to densification during sintering is accomplished by grain boundary diffusion. This interpretation is consistent with various diffusion models of the sintering process. 10-12 Vasilos and Smith calculate diffusion coefficients from their data which fit the equation D * 1.36 x 10* exp(-llO,700/HD However, no direct measurements of tungsten grain boundary diffusion have been made. Furthermore, considerable disagreement exists between the directly measured values of tungsten volume diffusion.&apos;-&apos; In order to corroborate the inferred results of the sintering experiments concerning grain boundary diffusion and to provide accurate diffusion data essential to the analysis of the kinetics of creep, oxidation, precipitation, and so forth, the present work was undertaken to measure self-diffusion in single-crystal and polycrystalline tungsten between 1400" and 2200°C. It is within this temperature range that tungsten sintering is done, the re crystallization of tungsten occurs, and the widest application of tungsten as a high-temperature material will probably be made. EXPERIMENTAL PROCEDURE Radioactive WlE5 was produced by irradiating tungstic acid in a neutron flux of 1.2 x 1012 neutrons per sq cm per sec for 36 hr. A 2-week waiting period was allowed for the decay of w"~ also produced by the irradiation. (w"~ has a half-life of 24 hr.) The half-life of the remaining isotope was determined to be 75 days confirming the presence of w lE5 and the absence of any undesired radionuclide. Specimens 4 in. in diam and $ in. thick were cut from polycrystalline swaged tungsten rods (recrystal-lized) and from Linde single-crystal rods. Chemical analyses of these materials appear in Table I. Actually upon closer examination, the single-crystal specimens were found to consist of several subgrains separated primarily by tilt boundaries in which the misor-ientation ranged from 3 to 10 deg. Thus, it was possible to measure boundary diffusion coefficients in these low-angle subboundaries as well as in the incoherent boundaries of the polycrystalline specimens. The two faces of each specimen were ground flat and parallel within 0.0001 in. The radioactive tungstic acid was dissolved in concentrated ammonium hydroxide, placed on the ground flat of the specimen, and evaporated to dryness. The oxide was then reduced in hydrogen at 1000°C resulting in a layer of wlE5 approximately 1 p thick. The diffusion anneals were performed in vacuum in a tantalum resistance furnace. Time at temperature ranged from 10 hr at 1400°C to 2 hr at 2200°C. The penetration profile was determined by measuring the residual activity after successive removal of surface layers by grinding on metallographic polishing paper. Extreme care was exercised to insure that sections were always taken normal to the diffusion direction; this was verified repeatedly by checking that front and back surfaces of the specimen remained parallel. The activity was measured with an end-window Geiger-Mueller counter. The sides and edges of the specimen were well-shielded to eliminate possible effects due to surface diffusion. The weight of the

Jan 1, 1968

By Eugene Grace

IN THE careers of the men to whom I have referred we find typified the development of the chief prob-lems of engineering. The first is to shape and direct the forces of nature and thus to bring the world&apos;s resources to add to the comfort and welfare of man-kind. That, in a word, is the problem of production. Engineers have made a supreme contribution to the solution of that problem. But I feel that we have two somewhat newer branches of engineering which must command more and more of our attention. Those are what might be termed commercial and human engineering. Of what value is all our efficiency in pro-duction if we do not distribute efficiently, economically and effectively? And of what value is any of it unless we can add to the happiness and deeper satisfaction of those engaged in industry, as well as those who enjoy its -products? I predict that the outstanding advances in business over the next ten years will be in improved merchan-dising and distributing methods. Herein lies a wide field of opportunity for the engineer. We have briefly reviewed certain qualities of engi-neers who have become successful business executives. Is it possible for us to say that the material success of all these men was due to any one characteristic com-mon to each one of them? Indeed, I venture to assert that there is one quality which, in the last analysis, is determining as to whether any roan shall realize material success in this world of ours. That quality-so notable in the character of each one of the men I have named-is sound judgment. Moments arise in every life when it is necessary to say "yes" or to say "no" to a particular proposition or to a proposed line of action. It is the man who says "yes" at the proper time and "no" at the proper time who, in the final analysis, realizes business success. The ability to do this wisely is the mark of sound judg-ment, which is necessary in a business executive. I have known many business men seemingly slow in their mental processes, possessed apparently, of little imagination and of none of the flair which gives fasci-nation to so many characters, and yet who, when crises come-be they big or be they little-are able so to steer their business courses that they move in the right direction instead of into shallow waters or upon the rocks of trouble.

Jan 4, 1928

By H. L. Talbot, R. S. Young, A. Golledge

The differentiation of oxidized forms of lead from lead sulphide in complex products by chemical analysis is of considerable importance to certain mining and metallurgical companies. A method for the separation of "oxide" lead, (non-sulphide), from sulphide lead, based on the solubility of the former and virtual insolubility of the latter in concentrated ammonium acetate solution, has been employed for many years in the industry.1,2 Unfortunately this solvent, while satisfactory for lead sulphate and carbonate, is without action on lead phosphates or vanadates, with the result that at .Rhodesia Broken Hill Development Co. where these latter minerals are present, they have counted as sulphides when using this procedure. For the control of operations in the new concentrator it became necessary to have a closer check on sulphide lead than could be obtained by the only current method of differentiating this constituent from oxidized lead. For some time this problem has engaged our attention, and after a large number of solvents had been tried, the following procedure was evolved. Like all methods depending on selective solution in a com- plex material, it will not give 100 pct separation into oxide and sulphide portions. Because of the ease of oxidation of galena this is almost an impossibility. Our procedure will, however, give a recovery of 99-100 pct of the oxidized lead, contaminated with very small quantities of lead sulphide, and a corresponding recovery of 97-98 pct of the sulphide lead. The procedure is simple and reproducible, and gives results quite .satisfactory for routine control purposes. Experimental For this work standard samples of the following pure lead minerals were obtained from Broken Hill, Northern Rhodesia. These were hand-picked specimens, and were carefully ground to —200 mesh. Since it was realized that a fair-sized sample would be necessary for this work to thoroughly test the large number of procedures we had in mind, a compromise had to be effected between a few grams of very pure minerals and a large sample of lower grade material. For this work the presence of gangue was not deleterious, so long as the oxide lead minerals did not contain lead sulphide, and vice versa. Table I shows the lead minerals used, and their total lead content, both theoretical and actual. Apart from the pyro-morphite the minerals are seen by analysis to be quite pure. Many solutions were tried in an effort to dissolve the oxidized lead minerals and

Jan 1, 1949

THE committee in charge of arrangements for the meeting of the Institute in September has com-pleted its program. The headquarters of the meeting will be at the Palace Hotel, San Francisco, and the registration committee will be at the hotel all day on Sunday, Sept. 24, and from 8 a.m. until noon on Monday. On Sunday afternoon, automobiles will be available for sightseeing trips around the city. Monday will be devoted to technical sessions. In the morning, there will be sessions on Mining and on Iron and Steel; in the afternoon, sessions on Mining and Milling. At these sessions, in addition to the papers mentioned in the tentative list printed in August, there will be presented three papers on the geology, mining and milling of the Comstock lode; one on the Aztec mine, Baldy, N. M.; one on the Colombian oil fields; and one on charcoal precipitation of cyanide solutions. The luncheon on that day will be Dutch Treat, for men only, at the Engineers Club. On Monday evening, there will be an informal buffet supper at the home of F. W. Bradley. On Tuesday morning, a party of 50 men will leave for Hetch Hetchy. During the four days of the trip, the party will see the Priest tunnel and earth dam under construction by steam-shovel and hydraulic-fill methods, the Big Creek shaft and tunnel, early intake power plant and tunnels and the Hetch Hetchy dam under construction. For those who remain in San Francisco, Tuesday will be "San Francisco Day." There will be motor trips to the Presidio, Cliff House, Golden Gate Park, and other points of interest, and shopping trips to Chinatown. On Wednesday, "University of California Day," the party will be guided through the university by members of the Mining Association, the affiliated stu-dent society, and will see the Greak Theatre and not-able buildings. Thursday will be "Leland Standford, Jr. University Day." Automobiles will leave the Palace Hotel at 10 a.m., and will return from the university at 4.30 p.m. Friday has been reserved for trips to the Selby Smelter, to Mt. Tamalpais, or to other points of interest. Arrangements will be made to visit the mines or gold dredges in California, if members desire to do so, but such trips must of necessity be considered special trips and arrangements will have to be made to suit the convenience of the individual or party. The Golf Committee will make arrangements for those who wish to play golf.

Jan 9, 1922

By P. W. Bakarian, John C. McDonald

Three magnesium alloys were processed in various ways to exhibit a wide variation in the ratios of yield strength and tensile strength in the rolling direction compared to the cross-rolling direction. Basal-plane pole figures were prepared from several specimens. A fair correlation was observed between the property ratios and the ratio of percent of poles oriented in the cross-direction quadrants compared to the percent oriented in the rolling-direction quadrants of the pole figures. THE modes by which magnesium crystals deform are such as to lead to marked preferred orientations in all forms of wrought products. The effect of the active modes at room temperature, coupled with these orientations, is often to produce a lower compressive yield stress compared to the tensile yield stress. The phenomenon is due to easy twinning in compression, and has been well-related to the preferred orientations as described by basal-plane pole figures of the hcp magnesium single crystal. The literature contains some information on the variation with test direction of the tensile properties of sheet, but no quantitative relationship to the observed pole figures has been established. These effects have been reviewed in the few com- prehensive treatises in English which have been written on magnesium technology and metallurgy.1°3 Roberts presents several pole figures, but no tensile-property data in the plane of the sheet. Raynor has no pole figures, but quotes Frommer&apos;s4 results. The information in Beck&apos;s compendium more or less parallels the results of Jones and powell.5 In both a Mg + 1.5 Mn alloy and a Mg + 4.6 A1 alloy, cold rolling was found not to change the general situation of higher properties in the cross-rolling direction,* than in the rolling direction. Thomas&apos;6 X-ray studies of Jones and Powell&apos;s specimens did not permit correlation of properties and preferred orientation. Ansel and Betterton7 report tensile and compressive properties on three other alloys as a function of degree of cold rolling, plus a recrystallizing anneal. As rolled, there was a change in anisotropy with degree of reduction, but all alloys were reasonably isotropic in tension when annealed. X-ray diffraction photograms illustrated the kinds of orientations present, but were not correlated with the properties. Bakarian8 has described a method of determining quantitatively a preferred orientation, and illustrated the method by applying it to pure magnesium and two of its alloys. This method was used in the present work as a basis for correlating the strength properties with the texture.

Jan 1, 1965

By William Sellers

tested without knowing anything of their chemical composition. I had these pieces separately placed upon 10-inch bearings under a 7-gross ton lianlrner, a piece of 2½-inch round iron laid upon them as a fuller, and the hammer allotved to fall from 20 inches above the fuller, which, according to Haswell, gave a ldow of 67.75 gross tons. The pieces were then turned orcr, the fuller placed upon the convex surface, and the harnnler allowed to fall from 13 inches above the fuller, giving a blow of 58.46 gross tons. You will see that the rails do aot show ally bigrls of ruptnre, and their color at the points of torture prove them to have been absolutely cold when the test was made. I thirk these rails ought to be reasonably safe in the track. As you see by this piece of the head of one of these rails, I had it plarred, and then some teeth cut in it by a cold clrisel, and one-half of them pounded down with a hammer. The teeth of my rack did not break off. The analyses of these rails substquently made are: I. 11. Carbon,... 0.110 0.880 Silicon,..0.050 0.058 Phosphorus ,..0.086 0.082 Manganese,.. 0.042 0 840 In conclusion, I will say that Dr. Dudley&apos;s paper as a contribu tion to our knowledge of steel rails is valuable and interesting, but I protest against his conclusions king reoeived as manufacturing or comtnercial axioms. From its being presented in the form-of a report to the leading railroad of the country from one of its trusted officers, as well as from the tone of the concluding deductions, it is liable to be so received by railroad men. If any railroad com pany desires rails made under either of Dr. Dudley&apos;s formulas, and are willing to pay a price large enough to cover the loss in making them, dl and good; but so long as the rail makers are compelled to gwrrantee the wear of their rails for a given number of years, justice reqnires that. the composition of the steel from which these rails are made should be left to them. WILLIAM SELLERS, PHILADELPHIA: The very interesting paper upon the wear of steel rails that has just been read preseak the record of a series of investigations that are extreniely valuable, and the deduction that bas been drawn from the results noted seems to be unavoidable; the tests, however, to which it is proposed steel rails shall be subjected hereafter, with a view to determine their quality, sllould

Jan 1, 1881

By W. N. Lacey, R. H. Olds, B. H. Sage

The volumetric behavior of five mixtures of black oil and natural gas and of two mixtures of condensate and natural gas from a field in the San Joaquin Valley was experimentally established. This work was carried out at roo°, I9o° and 250°F in the pressure interval between 400 and 5000 psi. The viscosity of the liquid phase of four mixtures of black oil and natural gas was experimentally measured in the above-indicated temperature and pressure intervals. The effect of methane upon the precipitation of bitumen from the black oil was studied at 230°F. Introduction The solution of a number of the economical and technological problems which arise in connection with petroleum production is dependent upon the availability of the necessary quantitative information covering the materials involved. This requires data concerning physical properties of naturally occurring hydrocarbon mixtures at the pressures and temperatures characteristic of underground petroleum reservoirs. The experimental determination of the desired data for each situation encountered is relatively time-consuming. However, it is considered to yield results sufficiently more reliable than those obtained from correlations to justify the effort. For these reasons there was undertaken a laboratory investigation of the viscosity of the liquid phase and the volu- metric and phase behavior of mixtures of oil and gas samples obtained from wells in a field located in the San Joaquin Valley. Terminology The nomenclature of petroleum engineering is not at present entirely standardized. Many commonly used technical terms are not everywhere given the same meanings. For the purposes of this paper the following definitions will be adopted: Black oil refers to the dark-colored, hydrocarbon liquid obtained when the producing horizon of the well lies partly in the condensed hydrocarbon phase of the reservoir. Condensate is the term applied to the relatively volatile, pale yellow or amber-colored hydrocarbon liquid that is often obtained from the surface separator system when the producing horizon of the well lies in the gas cap of the reservoir. The gas obtained from the surface separator system is called natural gas regardless of whether the well is producing black oil or condensate. As might be expected from the multi-component character of naturally occurring hydrocarbon materials, the compositions of black oil, condensate and natural gas are subject to considerable variation depending upon the temperatures and pressures prevailing in the surface separator system as well as upon the overall composition of the material produced from the reservoir. In order to obtain samples capable of reproducing the total hydrocarbon material produced by the well, all oil and gas mixtures used in this investigation were com-

Jan 1, 1949

By James Howe

EVERY engineer and user of wire rope is desirous of information that will enable him to determine whether the performance of any particular piece of rope is satisfactory, and what conditions can be changed so as to increase the life of a rope. In most cases, it is far from easy to analyze the conditions of service and tell which is the greatest factor in determining the life of wire rope. If we start on a layout for an entirely new rope system, the task of making conditions satisfactory is simplified so far as the engineering details are concerned; but if the plant requiring wire rope is in operation, any change is likely to involve the expenditure of consider-, able money to replace and change over machinery that must be kept in constant operation, because a large monetary loss will result from a shutdown for even a few days. Often wire rope is kept operating under bad conditions, as the user thinks that it is cheaper and quicker to replace the rope than to make alterations in the hoisting machinery. A typical case is a metal mine operating in what is now almost the center of a large mining city, where it owns a few acres of mineral rights. It was expected that the shaft would go to a depth of 1000 ft. (305 m.), so a moderate sized rope, about 1 ¼ in. (31.7 mm.), was used on a 6-ft. drum with a 7-ft. head-frame sheave and rather short lead from drum to head sheave. This mine has gone deeper each year until, it is now 2500 ft. deep and the rope speed has been increased from 1500 ft. per min. to over 3000 ft. The original rope just filled the drum in one layer, now it overwinds three layers. The original ropes were probably 6 X 19 crucible steel and lasted from 12 to 18 mo.; now, the highest grade plow steel is used, yet the average service is only about 6 mo. The cause is not hard to find. If the engineers had known at the outset what would be done with this hoist, the design would have been very different. Conditions at this mine, from a wire rope standpoint, have gradually become worse and it is difficult to see how rope service on this hoist can be com-pared with the service of previous years with any fairness to the wire-

Jan 2, 1922

By E. I. Larsen, E. F. Swazy, F. R. Hensel

Experience has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. Test MAteriaIs Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It mas found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended On the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as One eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from goo°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal com-position was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical propertties and certain bearing properties of this alloy are described in the present paper Preparation of Compacts Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition~ 25 per cent nickel; 7 silicon; 3 phosphorus 64 copper. This alloy is brittle in the cast condition and can be readily powdered. Sintering Procedure The blended powders were pressed at &apos;5 to 40 tons per sq&apos; in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By E. I. Larsen, E. F. Swazy, F. R. Hensel

Experience has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. Test MAteriaIs Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It mas found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended On the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as One eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from goo°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal com-position was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical propertties and certain bearing properties of this alloy are described in the present paper Preparation of Compacts Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition~ 25 per cent nickel; 7 silicon; 3 phosphorus 64 copper. This alloy is brittle in the cast condition and can be readily powdered. Sintering Procedure The blended powders were pressed at &apos;5 to 40 tons per sq&apos; in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By Arnulf Muan, R. E. Johnson

Equilibrium CO2 /CO ratios of a gas phase coexisting with selected oxide phase assemblages of the system CaO-"Fe0"-SiOz and vnetallic iron have been determined at 1080°C. The data obtained are used to calculate activity-conzposition relations for metasili-cute, orthosilicate, and CaO- "FeO" solid solutions, and to determine a new value for the free energy of formation of C&S&0,. The metasilicate solution is practically ideal, whereas large deviations from ideality exist in the othe,r two solid solutions. BECAUSE of the geochemical and metallurgical importance of the oxides CaO, "FeO", and SiOz, the system CaO-"FeO"-SiO2 has been the subject of several experimental studies during the past 30 years. Following the delineation of phase relations at liquidus temperatures by a group of investigators at the Geophysical Laboratory of the Carnegie Institution of Washington in 1933,1 Chipman and associates in the early forties2,3 determined activities of FeO in liquids of this system. Since that time, many attempts have been made to interpret the data of Chipman et al. in terms of the constitution of the silicate liquids and the interaction parameters among the various constituents of the system (see for instance papers by Richardson4 and by Flood and coworkers5). One of the assumptions made in some of these interpretations4 is that the binary silicate systems CaSiO3-FeSiO3 and CazSi04-Fe2SiO4 mix ideally in the solid state. The objective of the present study is to provide experimental data on activity-com position relations in solid solutions of the system CaO-"FeO"-SiO2. Such data will contribute toward an understanding of the thermodynamics of silicate solid-solution phases in general, and will serve specifically to confirm or refute some of the assumptions made in interpreting liquid slag behavior. PREVIOUS WORK Phase relations in the system CaO-"FeO"-SiO2 in contact with metallic iron were determined by Bowen, Schairer, and Posnjak,1 and additional phase-equilibrium data for this system have been presented by Allen and snow.&apos; A reproduction of the most up-to-date phase diagram for this system is shown in Fig. 1.7&apos;8 Of particular interest in the present investigation are the relations among the various crystalline phases slightly below the lowest solidus temperature in the system, as shown in Fig. 2. The present work will be concerned primarily with some of the composition

Jan 1, 1968