Search Documents

By R. J. Wasilewski

THERMAL expansion of rhenium data have been reported by Agte et al.,&apos; and Medoff and cadoff,&apos; respectively, while the linear expansion coefficient was determined by Sims et Al.3 Denoting expansion coefficients parallel and at right angle to c axis by all and Al respectively, their weighted mean should be equal to dilatometric linear coefficient of a random polycrystalline specimen. The values reported for these coefficients are tabulated below: Since these values are in poor agreement, and because of anomalous expansion behavior observed in titanium 4 and chromium, a rede termination of the axial expansion was carried out. A Unicam 19-cm-diam high-temperature camera was used, with unfiltered CuK radiation. Camera calibration was carried out using at Pt wire standarde at temperatures up to 1100oC, the variation between indicated and true temperature being within the experimental error (estimated at <3oC) above 750o C. Rhenium Johnson Matthey spectrographic standard) was vacuum annealed at 1000 oC prior to X-ray diffraction experiments. Lattice parameters were obtained by least-squares solution using the reflec- tions (1232), (1015), (2024), and (3030) for all the patterns, and the additional reflection (2133) for higher temperature (400°C and above) patterns. The relative expansion data obtained are shown in Fig. 1, lengths of the vertical bars indicating the spread in the parameter values obtained by using various combinations of three spacings from the four or five measured. The data calculated from the equation of Ref. 2 are included for comparison purposes. Several specimens were used to obtain the above data, neither of them showing a significant parameter change after completion of the high temperature runs. Some parameter data and the corresponding expansion coefficients between 25 oC and the measurement temperature are tabulated below. The comparison of the present data with those previously reported shows reasonable agreement with the results of Medoff and cadoff2 within the temperature range covered by them (up to 1000 oC). The a values are appreciably higher throughout most of the investigated temperature range. The basal expansion is—in agreement with their findings—appreciably higher than that in the direction of hexagonal axis. The expansion coefficient, al, however, decreases rather more slowly with temperature than previously reported. The expansion along the c axis up to nearly 1000°C appears in excellent agreement. However, at higher temperatures there is a marked deviation towards higher expansion, reproducible between different specimens. Furthermore, there seems to be some irregularity in the variation of all with temperature, the apparent local minimum and maximum values at 510o and 1024o C, Table II, being well outside the experimental error limits. It must be stressed that the apparent discontinuity in the c parameter expansion is still insufficient to account for the expansion value reported by Agte et al.&apos; since a total expansion of close to 2 pct would

Jan 1, 1962

By J. S. Dodge, I. M. Krieger

The laminarturbulent transition was studied for monodisperse rigid polymer latices as functions of particle diameter and concentration at several tube diameters. Breaks in the graph of friction factor US Reynolds number were used to characterize the transition; rates of shear were sufficiently high so that Newtonian behavior at the high shear limiting viscosity could be assumed. No abnormal behavior was noted at concentrations below 30 volume percent. At higher concentrations, suppression of turbulence was observed with critical Reynolds numbers rising to as high as 5,500 at 50 volume percent. No definite effect on the transition was noted due to variation of particle size or tube diameter. The type of surfactant used to stabilize the latex was found to have an important influence on the critical Reynolds number. INTRODUCTION For some polymer solutions and solid-in-liquid suspensions, the transition from laminar behavior to turbulence in pipeline flow has been reported to take place at unusually low1-5 and in some cases at higher than normal6,7 critical Reynolds numbers. Extreme values of critical Reynolds numbers (NRe*) have been found to range from 1 to 6,000, as opposed to the values of 2,000 to 3,500 which are obtained for ordinary liquids. Observations have also been reported of drag reduction in fully developed turbulent flow, i.e., a decreased value of the friction factor in the Reynolds number-friction factor plot6*10-14 in colloidal and polymeric fluids. In some cases, turbulence suppression (unusually large values of Nre*) was noted to occur preceding the drag reduction,6 while a normal transition was noted in other cases of drag reduction.14 To relate the occurrence of turbulence suppression and drag reduction to the molecular or particulate structure of the fluid, it is desirable to characterize the structural variables with some precision. For most colloidal dispersions and polymeric fluids, this is very difficult; particle sizes, shapes and stiffnesses may vary over wide ranges in the same sample. Recently, however, a colloidal fluid has become available which consists of rigid spherical particles of highly uniform diameter dispersed in a simple Newtonian liquid. These are monodisperse polymer latices, prepared by carefully controlled emulsion polymerization reactions. The purpose of this research was to study the transition to turbulence in these well-characterized colloidal fluids as a function of concentration, particle diameter and tube diameter. Typical flow curves of latices of high solids content are shown in Fig. 1. While these curves were obtained with monodisperse latices, the general shape of the curve is also typical of a polydisperse latex. It is observed that a shear-thinning region occurs for low to moderate rates of shear. At sufficiently high shearing rates a limiting Newtonian viscosity is reached. The viscosity µ diminishes with decreasing volume fraction 4 at all shear rates. For 4 less than 0.25, latices are Newtonian at all rates of shear.15 An increase in average particle size (at a given extends the Newtonian viscosity region to lower rates of shear. A third factor which influences the

By Robert Mehl

THE importance of the Widmanstätten structure to structure theory in metallography has been recognized by many writers.1 It is a structure produced by the precipitation of a new phase from a solid solution upon cooling as a result of changing solid solubility, and displays a characteristic appearance indicating a crystallographic relationship between the new phase and the original solid solution (Fig. 1). First discovered in 1808 by Alois de Widmanstätten2, the structure has been traced by analogy through many alloy systems. Particularly is this true of the steels. Sorby&apos;s classic work3 on the microstructure of iron and steel was in essence an attempt to explain the origin of this characteristic structure in meteoric iron. He observed in a Bessemer steel and in a cast-steel ingot structures which we now recognize as typical Widmanstätten figures.4 Osmond5 observed structures in a steel ingot analogous to those found in meteorites. Arnold and McWilliams6 obtained (and recognized) a

Jan 1, 1930

A discussion at a joint meeting of the New York Section of the American Electrochemical Society and the American Institute of Mining Engineers, Nov. 20, 1913. Chairman Lawrence Addicks:-Our program this evening represents an attempt to set before you the present situation and outlook in the metallurgy of zinc. It is a time-honored custom to throw bricks at the zinc man. The accusation is that he has borrowed a lime kiln and a gas retort and part of a sulphuric acid plant, hitched them together, and spent the last 50 years in regarding with holy veneration the reactions which take place in that retort. The copper man, who thinks of zinc as something with which copper is adulterated to make brass, and the iron man, who regards it as a sort of paint for corrugated sheets, and the lead man, whose opinion as to zinc is not fit for publication, have long felt that, when two or three of the minor details of their respective metallurgies were put in order, they would take a few clays and fix up zinc on a modern basis. But somehow there still seem to be some unsolved problems at home, and while we are waiting it seems only fair that the case for the defense should be adequately presented. There is probably no man in this country to-clay better able to do this than Mr. George C. Stone, of the New Jersey Zinc Co., on whom I have pleasure in calling to talk to us on "Progress in the Metallurgy of Zinc." George C. Stone:-It is frequently stated that there has been no change in the metallurgy of zinc since the first Belgian furnaces were built in the early part of the last century. It is true there have been no such spectacular and radical changes as were worked in the metallurgy of copper and iron by the introduction of converters; but, in the essentials, I believe the progress in zinc metallurgy has been as great as in that of the other common metals. The main reason that there have not been revolutionary changes is that the chemistry of zinc differs radically from that of the other metals and these differences control the type of apparatus that can be used. The differences are: 1. The temperature at which zinc is reduced by carbon is much above the volatilizing point of the metal and it is therefore always produced as a vapor.

Jan 1, 1914

By E. C. Wright

The following article is based on observation of college graduates entering the steel industry in technical work made during the Past 25 Years, the first five of which were spent as a college instructor in two engineering schools, and the last 20 in the employ of a large steel company that has hired hundreds of engineering graduates for steel-mill operations. The college graduates encountered during this period have come from many colleges representing schools in Eastern States, Midwestern Universities, many Southern colleges, and many smaller colleges and normal training schools mostly in western Pennsylvania and Ohio. The college training of these students for engineering work naturally has varied widely and the educational qualifications of the entrants have been in many ways different. It was found at an early date that graduates of standard engineering colleges were much more adaptable than graduates in science from nontechnical schools. The engineering students seemed to be more suited to actual work in steel plants and in general were better able to grasp a knowledge of the operations they observed. However, although the graduates of engineering schools have had somewhat better training in physics, mathematics, and engineering, it has been a general and continual observation that most of the students employed have had inadequate training in the fundamental sciences. Since this discussion relates entirely to metallurgical engineers it should be emphasized that students taking metallurgical engineering courses in college seem to be poorly trained in organic chemistry-physics, physical chemistry, thermodynamics, and any higher form of mathematics than simple calculus. It has been noted frequently that young engineers faced with problems in a mill that involve some mathematics generally flounder badly, and that they have little conception of physical chemistry. Another common deficiency lies in the young graduate&apos;s lack of knowledge of where to look for the more detailed literature on any subject. He reverts instinctively to some college textbook whose coverage is usually very elementary. It is recommended that such textbooks contain a bibliography of the source literature. and that students be taught to use the original data. Many of the students had had previous courses in college dealing with metallurgical work such as steel melting, metallograhy, etc.r but it was found that their grasp of these subjects was extremely sketchy. It was soon realized that an ordinary engineering graduate could be taught more about steel melting and manufacturing processes in a few weeks in a plant than he could learn in a college course on such subjects. A similar statement may be made regarding the ability of students to conduct laboratory work. Their lack of technique and skill in handling equipment and setting up experiments was soon apparent. It became neces-

Jan 1, 1948

By N. B. Davis

I. Introduction. II. Definition of Plasticity. III. Theories of Plasticity. A. Structure of the clay particles. (1) Fineness of grain. (2) Plate structure. (3) Interlocking particles. (4) Sponge structure of particles. B. Presence of hydrous aluminum silicates. C. Molecular attraction between particles. D. Presence of colloidal gelatinous matter. (1) Review of theory of colloids. (a) Suspension colloids. (b) Emulsion colloids. (2) Experiments. IV. The Formation of Clays. A. Residual clays. B. Transported clays. V. Summary. VI. Conclusion. I. IntRodUction While working with a number of very sticky cracking clays from western Canada the writer became interested in a study of the cause of the excessive plasticity. This led to a review of the rather bulky literature on the subject and the finding that plasticity still remains to be satisfactorily explained. Most of these investigations seem to have been carried on solely from the chemical viewpoint, the geologic aspects having been ignored. In nearly every case, the investigators have worked with the higher-grade clays of low to medium plasticity, such as the kaolins, the excessively plastic ones having generally been neglected, partly because of their limited application, yet the author believes that these are

Jan 1, 1915

By W. H. Emmons

In 1922 Morey made a series of experiments in which he observed the cooling of a molten system containing H2O, 9.1 per cent; K2O, 17.3 per cent and SiO2, 73.6 per cent. This system was confined in a bomb; it was fluid at 500° C. and exerted no vapor pressure. In cooling to 420° C. a large part of it crystallized and at that temperature much of the water had separated from the crystals and remained as steam, which built up a pressure of 4998 lb. per sq. in., a force sufficient to lift nearly one mile of granite.&apos; If granite, cooling at 600°, expels vapor in the process of crystallization it is reasonable to suppose that a considerably greater vapor pressure would result, and it is thought that the vapor expelled from crystallizing granitic batholiths probably has a pressure sufficient to lift two or three miles of granite. This vapor, collecting near the tops of cupolas of batholiths, is believed to exert sufficient pressure to fracture the hoods and roofs of batholiths above the cupolas. If that is true, one would expect to find that the fracture systems above cupolas are arranged in patterns that depend in part on the shapes of the cupolas. The mechanics of the situation seem to require that conical cupolas should have radial fracture patterns, that bluntly rounded cupolas should have fracture systems that are either irregular or rudely conjugated in plan, and that elongated stocks or cupolas should have fracture systems in which the fractu&apos;res lie nearly parallel to the direction of the elongation of the cupolas. Study of essentially all the cupolas of the earth that have associated important vein-filled fractures shows that this is generally true. This

Jan 1, 1935

By W. C. Maurer

Although millions of feet of rock are drilled annually, the basic drilling mechanisms involved are not well understood. The primary reason for this lack of knowledge is because the basic principles of rock failure are not well understood and rock failure is the primary mechanism in drilling. A better understanding of the drilling mechanisms would enable a more scientific approach to the design and use of drills and bits. The paper reviews several models which have been proposed to explain various aspects of the different drilling methods. These models are described and their limitations and areas of application are discussed. Drilling rate relationships are developed and related to the basic rock failure mechanisms. TYPES OF MECHANICAL DRILLS There are three basic methods of mechanically attacking rock: 1) percussive action, 2) rotary action, and 3) combined rotary-percussive action. A percussion drill applies a force perpendicular to the rock surface and the bit moves into the rock perpendicular to the surface, forming a crater beneath it (Fig. 1). A rotary drill applies a constant thrust to the bit while a torsional force moves the bit parallel to the rock surface, breaking the rock ahead of it. A rotary-percussive drill applies both a rotary force and a percussive force to the bit which moves into the rock at an angle to the surface. The commonly used drills can be classified as: rotary-drag, diamond; percussive-hammer, piston, churn; and combination-rotary-percussive, roller.

Jan 1, 1967

By Richard L. Ash

7.3-1. Introduction. All phases of mining competent materials are affected directly by the results achieved from primary blasts. It is imperative that their design suit each particular set of mining conditions. In general, the round design must provide an adequate tonnage of material, properly placed with suitable fragmentation, to ensure that loading, haulage, and subsequent disposal or processing are accomplished at the lowest possible cost. Blasting rounds are designed by the proper application of cratering relationships developed for the single, concentric, confined explosive charge. Blasting for surface mining and most open-cut heavy construction, however, is characterized by the use of rounds, composed of a number of explosive charges with relatively long lengths, which are placed in benches with specific finite dimensions. Therefore, modifications must be made to the classical, single point-charge cratering concepts. It is the purpose of this discussion to outline the basic principles, significant variables, and procedures for their integration in the design of rounds that are applicable to conditions characteristic of surface mining. Because relatively insensitive blasting agents will be used in most instances, particular attention must be given to priming, control of confinement, and selection of charge diameters that ensure complete explosive-reaction execution. 7.3-2. General Considerations. The primary requisites for any blasting round are that it ensure optimum results for existing operating conditions, possess adequate flexibility, and be relatively simple to employ. It is important that the relative arrangement of blastholes within a round be properly balanced to take advantage of the energy released by the explosives and the specific properties of the materials being blasted. There are also environ- mental and operational factors peculiar to each mine that will limit the choice of blasting patterns.

Jan 1, 1968

By Arne Westgren

ONLY in exceptional cases can the ordinary methods of chemistry be used for determining the constitution of compound metallic substances. Recourse has therefore been taken to special methods, the main expedients of which are, as we know, thermal analysis and metal microscopy. To these may be added-though more accessory-the determination of electric conductivity, specific volume, hardness or other properties. The information obtained by these methods has been compiled in equilibrium diagrams. Naturally, the technically most important alloys, such as steel, bronze and some others, have been subjected to very close study, and many investigators have devoted themselves to the solving of their problems of constitution. The equilibrium diagrams of these systems are therefore known today with a comparatively high degree of accuracy, even though it must be admitted that many details regarding their transformation reactions still remain to be completely explained. The equilibrium diagrams of the other alloys as a rule have not been determined so accurately. Most of them are based only on approximate determinations of the homogeneity ranges of the various phases. Thus extensive, detailed studies remain before these diagrams may be considered as established. Unfortunately, it must also be admitted that many of the alloy diagrams given in the present handbooks are as a whole very dubious. As a matter of fact, many of them may really only be viewed as the results of rather superficial, orientating investigations. In fact, there also seems to be a general opinion prevailing in our day that much work still remains to be done before the equilibrium conditions of the alloys may be considered as fully explained. At present, in almost all institutes for research on metals, as well as in many university laboratories, investigations to this effect are being carried out. As a rule, the classical methods of metallography, the thermal analysis and metal microscopy are applied.

Jan 1, 1931

By John J. McCabe

INTRODUCTION Over the years, Congress has written into the Internal Revenue Code various provisions aimed at lessening at least one financial burden faced by taxpayers in the mining industry - the federal income tax burden. These provisions include the election to deduct exploration expenses, the election to defer deduction of development expenses, and the percentage depletion deduction. Careful tax planning from the very beginning of a mining venture is essential in taking maximum advantage of these tax benefits. A major decision to be made is the choice of organizational structure. (For a more detailed discussion of this subject, see McCabe, John J., "Developing Structures for Investments in Mineral Property," New York University Institute on Federal Taxation, 42 NYU 24, 1984). One such structure is the use of multiple corporations, with mining activities conducted by one corporation and nonmining activities, such as manufacturing, financing and administration, conducted by the other corporation. This technique, which will be discussed in detail below, can be particularly advantageous in delaying recapture of previously deducted exploration expenses and in maximizing depletion deductions. TAX BENEFITS IN MINING Exploration Subject to certain restrictions discussed below, exploration expenditures (i.e., expenditures paid or incurred during the taxable year for the purpose of ascertaining the existence, location, extent, or quality of any deposit of ore or other mineral, and paid or incurred before the beginning of the development state of the mine are deductible at the election of the taxpayer (Section 617(a)).* Were it not for this option, exploration expenditures would be required to be capitalized and recovered through depletion, after production begins. Exploration of a mineral deposit can be very costly and may not result in commercial production for some time. If the taxpayer has income to he offset by the deductions, a mining venture can usually be structured in such a way as to allow the offset of mining losses against the other income. With today&apos;s high interest rates, this election can be quite valuable in present value terms. Corporate and noncorporate taxpayers are subject to different restrictions on this tax benefit. Corporations may elect to deduct only 85 percent of eligible exploration expenditures (Section 291(b)). (The Tax Reform Act of 1984 reduced this to 80 percent effective for expenditures after December 31, 1984, in taxable years ending after such date). The remaining 15 percent (20 percent after December 31, 1984) is capitalized and recovered at the same rate as five-year ACRS property (Section 291(b)). Individual taxpayers are not subject to this 85 percent rule; however, any amount deducted in excess of ten-year straightline amortization is a tax preference item for individuals (Section 57(a)(5)). Individuals may avoid the tax preference by electing to capitalize exploration expenditures and amortize them over ten years (Section 58(i)). In order to prevent the taxpayer from, in effect, converting ordinary income into capital gain by selling property that has given rise to exploration expense deductions, the Code requires recapture of such deductions upon the occurrence of certain events (Section 617): 1. Upon disposition of the property, adjusted exploration expenditures are recaptured to the extent of gain realized on the disposition (Section 617(d)). 2. If the property is leased, the lessor is disallowed any depletion deduction until his adjusted exploration expenditures have been recaptured in the form of foregone depletion deductions (Section 617(c)).

Jan 1, 1985

By R. Schuhmann, O. W. Moles

at temperatures of 1150°, 1250°, and 1350°C for liquid copper sulphides ranging in composition from saturation with Cu to about 21.5 pct S. From the experimental data, activities of Cu, S, and Cu2S in the melts were calculated. Also, the results furnish a new determination of the location of the curve showing the compositions of Cu-saturoted sulphide melts in the CU-S constitution diagram. THE "white metal" made as an intermediate L product in converting copper matte to blister copper is a matte approximating Cu2S in composition. It has long been known that liquid Cu-S mattes can exist at a given temperature over an appreciable composition range, with S:Cu ratios ranging up from a lower limit corresponding to equilibrium of the matte with a liquid Cu phase. The Cu-saturated matte has somewhat less S than Cu2S, although previous measurements of the compositions of Cu-saturated mattes are not in good agreement.&apos;" As the S:Cu ratio approaches and slightly exceeds that for Cu2S, the partial pressure of sulphur gas over the liquid matte rapidly approaches atmospheric pressure,5 so that Cu-S melts with much more S than Cu2S can be made and handled only in pressure apparatus. Accordingly, the liquid copper sulphides of interest in copper smelting and readily studied experimentally fall in a relatively narrow composi- tion range about Cu2S. The freezing points of Cu-S mattes show a maximum of 1129°C near the composition Cu, dropping to 1105oC for Cu-saturated mattes having less S and dropping under 1100°C for higher S mattes.&apos; Estimates of the sulphur pressure and other thermodynamic properties of liquid Cu,S were made by Kelley; based on extrapolations from equilibrium measurements on solid Cu,S. More recently, Cox and coworkers&apos; studied equilibria in the reaction: Cu,S + H, e 2Cu + H,S over the temperature range 700" to 1250°C. They measured equilibrium H2S:H2 ratios presumably with both the sulphide and the metal phase present, so that their data above the melting point of Cu,S should measure the S pressure of Cu-saturated sulphide melts. The sulphur pressures of liquid copper sulphides of several S:Cu ratios at their freezing points can be estimated from data given by Posnjak, Allen, and Merwin." However, beyond these few data, no systematic study seems to have been made of the relations of sulphur pressure and other chemical properties of liquid copper sulphides to composition and temperature. The measurements of the sulphur pressures of liquid copper sulphides reported in this paper represent a first step in the quantitative study of the chemistry of mattes. Similar work is planned on

Jan 1, 1952

By Roland D. Parks

Corundum, little publicized as an industrial abrasive, has, in its small way, contributed greatly to the production of many specialized items vital to our war program and to Our allies. Optical elements Of the highest quality for range finders, bombsights, and scientific instruments; precision metal parts for torpedoes and airplane engines; quartz crystal plates for military radios; armorplate and malleable castings for tanks and guns; and eyeglasses for everyone; these are some Of the products that corundum has helped to produce in the quantities needed and on time. Unlike metals and many other raw materials, corundum is not incorporated into any Of these finished products. It is simply a grinding medium used to produce the desired finish or precision; an operating supply or tool, so to speak. With a Mobs&apos; scale index of 9, corundum ranks next to the diamond in hardness among the natural minerals and is superior to emery and garnet. The gem varieties of corundum, including the Oriental ruby and sapphire, are frequently more highly prized as jewels than the diamond. It is the intent Of this paper to deal Only with a description of the corundum industry, the administration of wartime control, and certain economic aspects as seen by the author. Several references are listed to assist anyone who wishes further information on the geological occurrence of the mineral. Ore Production and Consumption For the past two decades, south Africa has been the world&apos;s sole producer of corundum ore. A possible exception is Russia, where, it is understood, there was considerable production during the thirties for domestic consumption but for which statistics are lacking. The United States is the world&apos;s principal consumer of corundum ore; imports lor the period 1934 through 1940 averaging 3000 Short tons per year, The years 1935 and 1936 were close to the 5000-ton mark, and imports during 1941, the last prewar year for which statistics have been released, were approximately 6000 Short tons. Again lacking statistics on Russia, the United Kingdom ranks second, but far below the United States in consumption of ore. Historically, corundum has been found in some 35 countries throughout the world, but the principal deposits are in South Africa, Canada, Madagascar, Russia and the united States. Deposits are generally small and subject to rapid exhaustion. Thus, the United States was the principal world producer for the period 1870 to 1900, when operations ceased except for two years during World War I. India was a producer of ore from 1898 through 1921, with peak output in 1916 through 1918 Canada came into production in 1901 with substantial output of ore and finished grain until 1914; the production thereafter was smaller until 1921. Madagascar has produced ore since 1910 but has had important output in only a few scattered years. South African production started in 1912

Jan 1, 1948

By Walter R. Hibbard, Walter L. Finlay

INTRODUCTION THE key feature of the lattice coherency theory of precipitation hardening1-6 is the forced coherence between matrix and precipitate which elastically strains both lattices and is believed to be the major source of strengthening in precipitation hardening. In systems exhibiting age hardening, the atom movements leading to precipitation are not at all extensive and are such as to require the minimum amount of energy to produce the interface; that is, the new lattice forms in such a way as to be as nearly as possible a continuation of the old with a matched, coherent plane at the interface at least during the initiation of the precipitation. The crystallographic sequence whereby regions of the matrix change to the precipitate lattice usually can be resolved into a set of shearing operations.5,6 Conversely, the perhaps novel speculation is made that solution of a second phase is accompanied by shearing movements which are possibly the reverse of the precipitation shearing movements. A basic premise of the investigation reported in this paper is that precipitation and solution shearing movements constitute structural weaknesses which might cooperate with applied stresses to facilitate plastic deformation. Another basic premise of the investigation is that the application of hydrostatic pressure to a precipitation hardening system will significantly alter the degree of disregistry across the matrix-precipitate interface and thereby significantly affect the course of age hardening. Two binary precipitation hardening systems were investigated: 12 pct zinc in aluminum which undergoes transformations, both precipitation and solution, by a simple crystallographic mechanism; and 4 pct copper in aluminum which undergoes a complex transformation in precipitating and dissolving a second phase. The effects of the application of uniaxial tensile creep stress during elevated temperature aging of both systems and of hydrostatic pressure during the elevated temperature aging of 12 pct aluminum-zinc were then investigated. Previous Investigations Van Wert in 1935,7 studied the effect of hydrostatic pressure on the room temperature age hardening of a few precipitation hardening systems. The latter were rather unfortunately selected since none is known to exhibit any marked volume change on aging and the majority were complex commercial alloys the precipitation mechanisms of which are not known. Jenkins, Bucknall and Jenkinson,8 in 1944, applied tensile creep stresses to a complex coppernickel-silicon alloy at various temperatures. The complexity of the alloy and the industrial objective of the work did not permit an appreciable addition to the theoretical understanding of either deformation or precipitation hardening.

Jan 1, 1948

By Benjamin Tillson

To MOST mine operators, it seems evident that there is a drill-steel problem, although under certain conditions the amount f drill-steel breakage does not appear serious. What is at fault? It may be one or a combination of circumstances. The development of rock drills to the hammer-drill type in place of the old reciprocating piston drill, probably is one important cause for the greater steel breakage. Perhaps the manufacturers of drill steel have failed to realize what alloys are needed for this new service or have overlooked the changes in the art of rock drilling. Although suitable alloys are provided, they may not be so handled in the manufacturing process as to be in the best condition to withstand the demands of rock drilling. The mine operator may be at fault in desiring to use the smallest possible drill-steel section in order that the gage of the drill bits may be correspondingly small and the amount of footage drilled per unit of labor may be greater; or the black-smithshop practice at the mines may need improvement. The miner who uses the drill steel may also require more intensive supervision and education. Again, the manufacturer of rock drills may have failed to study the types of blows the steel alloys will withstand satisfactorily and which their tools are delivering and so he may not know whether or not a different design of rock drill would equal or excel their present drilling speeds without treating the drill steel so severely. All of these hypotheses probably have their supporters. On the other hand, perhaps we are seeking too much service from drill steel and we need a fuller realization of the fatigue strains developed and should prepare to relieve these by a periodic heat treatment of the steels. However, we do not find any proof that any of these suppositions may be held responsible for the drill-steel breakage attendant to mining. The proposed investigation of this matter by the U. S. Bureau f Mines is fully warranted in the promotion of the conservation of labor and material, and the safety of the workmen. The great range of field conditions, as well as the scope of the research, requires the energetic cooperative support of many interests. Various manufacturers of steel,

Jan 5, 1921

By John E. Latz

QUICKSAND far below the surface, stopped two attempts by the Potash Co. of America to sink a third shaft to a potash bed that lies 1000 ft below the southern New Mexico desert. Virtually all methods of grouting were employed in the two failures without any indication of consolidation of the flowing sand. Sinking the South Shaft at the Carlsbad potash mine seemed an almost insurmountable task, until freezing was employed as a final resort. This process that proved to be the answer may be defined as "the sinking of a shaft by freezing, consists of the formation, in the water-bearing strata, of a large block of frozen ground in which it is possible to sink a shaft without danger of an influx of water, providing the ice-wall between the water outside and the shaft itself is strong enough to resist the hydrostatic pressure." Freezing Method Used Extensively in Europe Successful frozen ground shaft sinking projects had been completed in Europe, and Russel G. Haworth, resident manager of the Potash Co. of America, went abroad in search of the know-how needed for the New Mexico undertaking. The freezing process, with a history of two failures at the time, was first successfully employed by Poetsch in 1885 at the Houssu Collieries near Haine St. Pierre, Belgium. Poetsch contracted to sink the remaining 64 ft of an uncompleted shaft through water laden strata from a depth of 190 ft to a depth of 254 ft. This work was in progress until 1887. The freezing and sinking consumed more than two years. As a result of early failures, the process was not favorably received until soon after the turn of the century. The accurate prediction of success in a given application was made possible by the concerted effort and study of a group of European engineers. Means of accurate deviation measurement and control were devised, the nature and properties of frozen water laden soil (the ice wall) were investigated, a thorough and rational basis of refrigeration load calculation developed, and concurrently the efficiency and dependability of refrigeration machinery was greatly advanced. Numerous shafts in Germany, Belgium, France, and England today testify to the reliability and economical surety of the freezing method. Applied to the South Shaft, which is circular in cross-section and 15-ft diam, the freezing method consisted of drilling holes 350-ft deep, through the water bearing strata into impervious ground-the freeze hole pattern being concentric with the shaft and 31-ft diam. The holes were cased with pipe closed on the bottom end. Smaller tubes were placed inside these casings and connected to a header supplying chilled brine from a refrigeration plant. The brine descended in the tubing to the bottom of the hole and ascended through the annular space between the two pipes to the top of the casing; flowed into the return header and back to the refrigeration plant. Under these conditions, each of the freeze hole casings became surrounded by a cylinder of ice

Jan 1, 1952

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin. The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most bromising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestern Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1948

By Richard P. Rothwell

Fires in mines are so serious in their consequences and of such frequent occurrence, that their causes and the means of extinguishing them are certainly questions of the greatest interest to a large part of the engineering profession. We have already, in this country, many mines which have been burning for years, and though our hard anthracite is so difficult to ignite that for a quarter of a century after it was first discovered it mas not known how to burn it except with the aid of an artificial blast, yet most of the fires which have occurred underground have been in anthracite mines, and in the coal itself. The injury which these fires have caused to properties in various parts of the anthracite regions, and the cost of extinguishing them, would amount to many millions of dollars, and they have also occasioned the loss of many valuable lives. It is not surprising, therefore, that the subject has already attracted much attention, and the exercise of great ingenuity; and the present communication is made less with the expectation of announcing anything new, than with the object of putting upon record the present state of our knowledge on this subject, or, in other words, of indicating how defective are the present means of combating underground conflagrations. Causes of Mine Fires.—Even upon the surface, fire is a terrible foe to contend with, and there is probably no other which inspires such thorough and well-founded alarm. With what feelings, then, must we look upon this destructive element, when its field is in the narrow galleries of a mine, where the poisonous products of combustion, spreading in every direction, protect, in the most effectual manner, the fire itself from the attacks of extinguishers, while, if the face of attack be ventilated so as to enable then] to approach the seat of the fire, the air current simply increases the extent and violence of the conflagration. Fires underground originate in as various ways as those on the surface, and it is scarcely necessary to say that, except in the rare cases where they are the result of design, they are invariably classed as " accidents," and most generally as " unavoidable accidents." In reality, by an intelligent understanding of their causes and with due precautions, they can almost always be prevented. Ignorance and

By C. Chiou, D. P. Seraphim

The effect of clustering on the superconducting properties of Al-Zn alloys has been studied by the ballistic induction techniques. The superconducting critical temperature, T,, changes when zinc-rich clusters are formed. The change in T, depends on the concentration and may be positive or negative, but always correlates with an effective decrease in the solute concentration of the alloy. Reversion after clustering effectively returns a 5 at. pct Zn alloy to the quenched state. These methods might be use&lly extended to the Al-Mg system, where X-ray data are difficult to obtain. In very dilute Al-Zn alloys, as in other tin,&apos; indium, aluminum,2 or tantalums base solid solutions, there is a decrease in the superconducting critical temperature, Tc, roughly proportional to the temperature independent resistivity, i.e., -0.2°K per pS2cm. With increasing solute concentration, the T, generally reaches a minimum and then increases4 to a value well above that for the pure solvent. The change of T, with solute concentration follows an empirical formulation involving two constants which correlate with the scattering cross section of the impurities. As will be shown below, the Al-Zn alloys more concentrated than 1or2at. pct do not follow the empiricism, probably because they are unstable even when rapidly quenched.5 However, it seems possible to study at least the later stages of solute clustering by precise measurements of the 1&apos;, following various thermal treatments. A few experiments on quenched alloys, aged alloys, and tests on reversion are reported here. The heat treatments selected for obtaining the quenched and aged states were mainly deduced from the work of Dash and Fine.6 For the quenched state, specimens were homogenized at 480°C, quenched to -160°C, and immediately transferred and mounted in liquid nitrogen. Measurements on the superconducting properties and residual resistivities were then made at helium temperatures, after which the specimens were aged at room temperature for 3 to 5 hr, i.e., much longer than the time required for clustering to be essentially completed. The superconducting properties and residual resistivities were once again examined. To reach the reverted state of the A1-5at. pct Zn alloy, the aged specimen was heated for 5 min at 200°C and then tested as above.

Jan 1, 1963

By Lawrence B. Wright

THE Republic district, Washington, is of new interest because of the discovery of new gold-silver ore within a unique structural pattern. The camp was revived in 1937 following installation of a plant to treat low-grade disseminated ore at Knob Hill and further stimulation followed discovery of "cross vein" breccia ores in 1939. Previous writers 1-2 ascribed the quartz veins to a latite porphyry stock, but are in disagreement as to its precise location and extent. This study leads to the conclusion that the ores have a more profound parentage linked to a broad system of thrust faults and folds, the mechanical origin of which is related to a southward trending (Sanpoil) syncline connecting with the Lewis and Clark zone of shift described by Billingsley and Locke3 in 1939. The Republic anticline and a cross anticline recumbent against Cretaceous granodiorite, and involving some 4000 ft of Eocene andesite flows and early Miocene lake beds, localize the ores, mainly along the east flank, in a series of openings simulating drag folds and steeper than the folded flows. These broad structural features no doubt reach deeply into the basement rocks, where at appropriate crossings and junctions it is suggested that heat effects gave rise to oremaking materials, including, in this instance, intrusive breccias that later were mineralized, and comprising the broader bodies of new ores. The breccia ore is seen crosscutting the earlier narrow quartz veins with a welding of the two at junction areas by a second surge of ore minerals. The ore mined and developed since 1937 equals district production from 1896 to 1937. The ores are typified by cherty quartz, adularia and some barite, with fine pyrite and marcasite, polybasite, pyrargyrite, tetrahedrite and gold. Selenium is present, possibly with gold, as a normal selenide. The disseminated ores, as well as the vein and breccia ores, are localized principally in one 500-ft flow (Knob Hill andesite), which has been traced around the crest of the low northward-plunging Republic anticline. The gold-silver ratio in the earlier narrow veins is about 1 to 4 and in the disseminated and breccia ores, 1 to 7. The latter higher silver ratio is deemed to reflect the character of the second surge of mineralization. Sills and dikes of the Columbia River (Miocene) basalt cut the folded structure and ore, thus placing the mineralization in the middle Miocene.

Jan 1, 1947