Search Documents

By Harlan A. Walker

Rock-drill steel has an important bearing on costs in many mining operations, both directly and indirectly. Direct factors include such items as shop expense, steel consumed per ton of ore produced, cost of distribution and the dust hazard. The latter, although no specific amount may be assigned to it, is an ever-present problem, and is receiving increased attention as the science of mining progresses. Indirectly drill-steel performance affects consumption of compressed air, maintenance of drills and drilling speed. The latter, in turn, increases or retards the tempo of mining and development. These factors, while not all inclusive, are preponderant in their importance. Thus it is evident that in an extensive operation drill-steel expense may run to many thousands of dollars and that thoughtful research leading toward more efficient practice is warranted. Experimental Work During the late spring of 1939, experiments were undertaken at Homestake in reducing changes in drill-steel gauge from ? in. to 1/16 in. In drifts and crosscut headings mounted machines were set up and holes were drilled with ?-in. bit-gauge changes and other holes a few inches

Jan 1, 1940

By C. H. Page, Brenne

Theoretical modelling of a proposed sub-level open stoping mining system was carried out to assess pillar instability and potential for hanging wall caving. This modelling was done, at first, without detailed information concerning the rock mass structure and classification. After mining commenced, the deviance in behaviour from that predicted by the modelling indicated that the structure was having an appreciable modifying effect on behaviour. Further analysis was carried out with detailed engineering geological information and a recently developed pillar design method. The outlined procedure produced results for pillar size and strength that explained the behaviour that had been recorded.

Jan 1, 1983

By Moshe Sheinkin, Douglas E. Julin

Large tonnage operations face many problems in adequately planning ahead for future years production. In order to maintain desired levels of production, such problems as source of tonnage, man- power and equipment requirements, tailings disposal and water requirements must be anticipated. Of course, before any of these problems can be analyzed, daily tonnage requirements and its source must be determined. Looking ahead for one year or even two or three is usually not sufficient time to adequately prepare an area for production. Because of the sequence of mining and the multilevel nature of the 42,000 tpd Climax mine in Colorado long-range planning must be on a ten-year basis. By using a ten-year base, adequate time is allowed to gain access and prepare a new level for production. Usually eight years will be required for this phase of the initial mine preparation. Once production has been started on a level and access to the area is available, three years is usually sufficient to prepare a new block for production as long as it follows in the normal sequence of mining.

Jan 4, 1967

By A. P. Miller, T. S. Washburn

Improved procedure in the manufacture of rail steel has come as the rail user demanded better wearing qualities combined with greater unit weight. With each weight increase per lineal yard has come greater difficulty in making a product that would successfully withstand all tests that modern rails must meet. With these facts in mind, and with a sincere desire to produce a rail whose service in track would be satisfactory in all respects, the steelmaker was quick to realize that all of the factors entering into his process would have to be more closely controlled. Control of rail-steel slags was recognized as one of the most important of many interdepending factors. The object of slag control is to hold the slag compositions within a range that gives the best results with respect to economy of production, uniformity of analysis, and quality of the finished rails. The most important component of the slag from the standpoint of these production and quality factors is the ferrous oxide content. This component is a good indicator of the basicity and oxidizing power of the slag, and these largely govern the effect of the slag on the steel. Consequently, the

Jan 1, 1935

By C. G. Massey, L. C. Acton

A first-class haulage level railroad was considered of prime importance during planning of San Manuel because successful operation of the mine would hinge heavily on the ability to move large tonnages of ore rapidly, safely and efficiently. These principles, plus certain techniques developed from experience on the 1475 level, are being employed in preparation of the 2075 level. At full production, twelve 23-ton trolley locomotives, each pulling fifteen 12-ton capacity ore cars, and fifteen 8-ton battery locomotives engaged in development, service and supply, will be in operation on the 2075 level 24 hours per day, seven days a week. More than 35,000 tons of ore will be transported every 24 hours. GENERAL DESCRIPTION The rail haulage system is designed to comfort- ably move twelve 180-ton payload trains per hour through the rotary dumps pulled by 23-ton trolley locomotives. The rail system is laid out as a simple double loop with one-way traffic of continuous haul as shown in the above diagram, and is comprised of about 30 miles of track on the 2075 level.

Jan 3, 1962

By John W. Lane, Richard A. Ronzio, Frederick N. Bender

Climax Molybdenum Co. operated a hydrometallurgical plant at Climax, Colo., from August 1966 to August 1968 to recover molybdenum from an oxidized ore. The feed, tailings from sulfide flotation, was first upgraded by cycloning. The concentration plant handled 6000 tpd of feed and produced 2000 tpd of slime concentrate. The concentrate was leached by a sulfuric-sulfurous acid solution at 65°C. The molybdenum was solubilized in the form of "molybdenum blue." Activated charcoal was added to the leach tailings in a resin-in-pulp type circuit. Molybdenum was adsorbed on the charcoal. The charcoal was screened from the pulp and washed. The washed charcoal was pumped to columns where it was ammoniated and air-blown. The oxidized molybdate then was washed from the charcoal. The eluate was evaporated until ammonium dimolybdate crystallized out. The ammonium dimolybdate was calcined to molybdenum trioxide.

Jan 1, 1973

New York Meeting, October 16 and 17, 1913.-The One Hundred and Sixth meeting of the Institute for the reading and discussion of professional papers will be held in New York City, on Thursday and Friday, October 16 and 17, 1913. Headquarters will be at the Institute office in the Engineering Societies Building, 29 West 39th Street. The sessions will be held in one of the assembly rooms of the building. Because of the many valuable papers on iron and steel obtained with the assistance of the Iron and Steel Committee, which papers could not appropriately be presented and discussed at the Montana meeting, this October meeting of the Institute is held for the purpose of reading and discussing these papers, most of which will be printed and distributed in advance. The members of the following societies have been invited to attend the meeting, and several have accepted and declared their intention of taking part in the proceedings: American Society for Testing Materials, American Iron and Steel Institute, American Society of Mechanical Engineers, American Society of Civil Engineers, American Institute of Electrical Engineers, American Foundrymen's Association. The meeting will be conducted under the auspices of the Iron and Steel Committee, and the latest revised program of the proceedings will be found on page xi, under the notes of this Committee.

Jan 10, 1913

By Frank T. Wheby

The cost of tunneling is highly sensitive to the rock characteristics through which the tunnel is to be driven. These characteristics affect in a major way the rates at which tunnels and shafts can be driven and the degree to which the openings must be supported to maintain them in a permanent stable condition. Tunnel and shaft design and cost criteria have been computerized, permitting estimates of tunnel-shaft systems to be made directly from inputs of rock mechanics characteristics and other data. Curves of quantities of steel, rock bolts, and other rock support items as related to tunnel size and rock quality designation are presented. An illustrative example of the use of the program in calculating the cost of a hypothetical tunnel system is included.

Jan 1, 1971

US Tin Mission To Study Costs in Far East A move to obtain adequate supplies of tin at prices the United States is willing to pay was initiated when the interagency tin mission left for the Far East. The Mission, which includes representatives of the Reconstruction Finance Corporation, State Department, Defense Minerals Procurement Agency and the Bureau of Mines will go to Indonesia and Malaya. The primary purpose of the mission, according to officials, will be to study tin production costs, not to negotiate for the purchase of tin. The mission will be prepared to enter into negotiations, if the Far Eastern producers are amenable. The United States withdrew as a large-scale buyer of tin some months ago in protest against what it considered exorbitant prices being charged in the Singapore market. Subsequent attempts to negotiate for a steady tin supply at what this country considers reasonable prices have been unavailing. The U. S. is prepared to enter into a two or three year contract with the price of tin somewhere between $1.00 to $1.12 per lb. The decision to abstain from the market has not yet put a squeeze on U. S. supplies. Substantial quantities of tin still are coming in from Malaya under an old contract.

Jan 12, 1951

By Paul Weir

BLEACHING clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller's earths fall within the general group of bleaching clays and gradually the commercial term "fuller's earth" has been applied to natural clays originating, for the most part, in the south- eastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States. Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). [ ] The fuller's earth type of clay is characterized by a lack of plasticity, relatively adsorbent, foliated structure, and does not swell to form a

Jan 1, 1939

W. H. SHOCKLEY, Chairman, FRANK H.-PROBERT, :Vice-Chairman, T. A. RICKARD, Sec.-Treas.; 420 Market St.,. San Francisco, Cal. C. C. BRAYTON, J. F. NEWSOM. A Meeting of the San Francisco Section was held on May 7, 1917. Chairman Shockley was in the Chair. The Section was honored by the presence of President Moore and Secretary Stoughton of the Institute. C. W. Merrill introduced President Moore, who then spoke to the Section on the Aims of the Institute. He discussed the possibility of improving the standards of membership by introducing a classification of membership. The present rigid investigation of applicants was pointed out by him. He spoke of the important influence that the local Sections can exert on the Institute and of the importance of sociability and informality at the meetings. Secretary Stoughton, who was introduced by the Chairman, emphasized somewhat the same points. He mentioned the need for making the Bulletin of the Institute more, interesting than it is at present, this to be accomplished by raising the necessary funds by increased advertising. He asked for an expression of opinion on this point. He. said that the employment department of the Institute is now used extensively. At the request of Mrs. Mark L. Requa, Mr. Stoughton. announced that a San Francisco branch of the Woman's Auxiliary of the, Institute was being formed and asked that the ladies of the members' families send in their names to Mrs. Requa or to the Secretary of the Institute.

Jan 10, 1917

By H. I. Smith

THE technical and safety press have devoted much space in support of or in opposition to the use of booster and auxiliary fans in coal mines. The Mine Safety Board of the U. S. Bureau of Mines has given the matter consideration, and the Mine Ventilation Committee of the A. I. M. E. is now seeking a discussion of the merits and demerits of such fans to guide it in formulating recommendations. In this paper, I will set up some principles on which I believe most engineers will agree and from which we may work toward a decision, though as to what that decision shall be there may be a difference in opinion. Before stating the points on which I believe. there is accord, I will distinguish between booster and auxiliary fans.

Jan 1, 1927

By L. A. Roe

The flotation of fine particles less than five microns in diameter and the flotation of liquids from liquids generally requires bubble generation methods different than methods used in dispersed air type machines used in mineral flotation. Conditions in the separatory zone in mineral cells are generally more dynamic as compared to the quiescent conditions often absolutely necessary for the flotation of fine particles and liquids. An example of quiescent flotation with very fine bubbles is the lithium flotation plant which operated at Trona, California for 34 years, until it ceased operations in 1978. A review of the process development and the commercial flotation operations at Trona is given in this paper. The clarification of oil field brines by flotation of the oil from the brine has been used for over twenty-five years. Recent installations related to the Prudhoe Bay oil field and the Alaska pipeline are described.

Jan 1, 1980

By R. F. Mehl

Jan 1, 1961

By W. L. Freyberger, H. Alter, K. L. Woodruff, E. L. Michaels

Laboratory and pilot scale tests have been made to determine the utility of heavymedia separation, particularly a cone-type separator, as a means of recovering aluminum and other values from shredded municipal solid waste. The effect of the method of shredding on the behavior of aluminum in a heavy-media system was determined. Two-stage pilot-scale heavy-media separations were made with size fractions of shredded refuse. Recoveries of aluminum, as well as other components of the refuse, were measured and medium losses determined. The experimental results indicate that with certain reservations a heavy-media cone system can be utilized for aluminum separation and recovery from shredded and air-classified municipal solid waste. Observations made using two-stage heavy-media separation in a drum unit are included. Qualitatively, the results from the two types of separators are similar.

Jan 1, 1976

By J. D. Miller, A. Cortez, J. Hupka

The separation efficiency of the hot water digestion-flotation technique used for bitumen recovery from various domestic tar sands was evaluated. Bitumen viscosity was found to be the most important tar sand property in determining the success of the bitumen separation. Bitumen viscosity of the tar sand war controlled by changes in digestion temperature and/or changes in diluent (kerosene) addition. Complete and uniform dilution of the bitumen phase was achieved by providing a sufficient presoaking, or penetration time, for a given tar sand type. For all the tar sand samples tested, an excellent correlation was obtained between the coefficient of separation and the bitumen viscosity. To achieve a satisfactory coefficient of separation, it was found that the bitumen viscosity must be reduced below 1.5 Pa.s (16 P) at the temperature of digestion. This was the case regardless of the tar sand type, grade, or origin.

Jan 1, 1984

Each spring most secondary schools select their best student science exhibits, prepared during the preceding academic year, and send them to regional "Science Fairs", which now number over 220. Winner-finalists of these regional contests are then sent to the annual National Science Fair, conducted by Science Service, a non- profit institution for the popularization of science, for final judging. (The Fair is now known as the "National Science Fair-International" because of participation by finalists from Japan, Thailand, Germany, France, Sweden and Canada.) For the first time since the Fair was started in 1950, AIME participated in the awards presentation. Held this year in Baltimore, Md., from May 5 to 9, five members of AIME's Washington, D.C., Section consented to represent the Institute as judges. They were: Marlin J. Ankeny-Director, Bureau of Mines, U.S. Department of the Interior. Kenneth N. Weaver-Director, Maryland Department of Geology, Mines, and Water Resources. William Harper-American Petroleum Institute. Vice-Chairman, Washington Section, AIME.

Jan 7, 1964

By Eric A. Nordhausen

A good deal of dialogue has been published and voiced concerning one mining regulation or another, that, according to those raising the issues, in effect shuts down or drastically reduces mine and/or mill reduction. The objective of this discussion is to there fore synthesize the various regulations affecting the uranium mining industry and attempt to realistically assess the extent of impact to yellowcake production - on both an individual and collective basis. Emphasis is placed on the later or newer permitting requirements under the Mill Tailings Act, Underground Injection Control Program, the Consolidated Permit Program, and the Resource Conservation and Recovery Act (RcRA).

Jan 1, 1980

By Thomas S. Lovering

Hot springs, geysers, steam-emanating fumaroles- these creatures of nature were until recently little more than geological curiosities, but today they are exciting the interest of engineers around the world for it has been shown that such hyperthermal areas can be profitably harnessed by man to provide heat and power for his communities. Although water from hot springs was used centuries ago to heat some Korean dwellings, is being used today by one-third of Iceland's population for similar purposes, and is finding industrial applications in New Zealand and elsewhere, the most dramatic use of geothermal energy has been its conversion into electricity. The largest installation at the present time is that at Larderello, Italy, where the Count of Larderello began to experiment in the production of electricity from geothermal steam in 1904. Eight years later after a quarrel with the local power company, the Count installed his first steam turbine, a unit of 250 kw capacity.

Jan 9, 1965

By George J. Simchuk

Selection of an applicable stripping method and the subsequent determination of appropriate sizes of selected equipment are discussed. The case in point is Utah International, Inc.'s Goonyella mine located in central Queensland, Australia. A detailed study of the various types of stripping methods now practiced throughout the world led to the conclusion that large draglines would be the logical choice for Goonyella. The optimal size of dragline was then determined by first designing a series of cut diagrams using an array of machine and pit geometries followed by a cost comparison of the various sizes of machines, in terms of their effective spoil radius. A dragline with a 51-cu-yd bucket was determined to be of optimum size. Further calculations, incorporating total overburden moved from both the highwall and spoil sides, required that four drag lines, two equipped with 40-cy-yd buckets and two with 54-cu-yd buckets, be used to satisfy the stripping requirements at Goonyella.

Jan 1, 1973