Search Documents

By J. E. Hilliard, H. E. Cook

It is shown that for systems having a miscibility gap the spinodal composition (c,) in the vicinity of the critical temperature (Tc) is related to the equilibrium composition (c,) by where cc is the critical composition. This expression is exart for the limit T — Tc and is a good approximation down to (T/Tc) - 0.9. If the miscibility gap meets the composition of the pure components THE recent theoretical treatment by cahn1,2 on spinodal decomposition of solid solutions has revived interest in methods of estimating the chemical spinodal, * i.e., the locus on a binary phase By use of the appropriate expression, the spinodal can be drawn on the Phase diagram almost by inspection with an accuracy comparable to that of lengthy calculations in which a free-energy function is fitted to the phase diagram. Satisfactory agveemenf is also obtained with spinodals comPuted from experimental free-energy curves. where G is the Gibbs free energy of the homogeneous solution and c the atomic fraction of component 2, the derivative being evaluated at constant temperature (T) and pressure (P). (These subscripts will hereafter be omitted from the partial derivatives.) If experimental measurements of G as a function of c and T are available in a single-phase region above the spinodal, then these can be extrapolated to obtain a series of metastable free-energy isotherms in the two-phase region, and from these isotherms a series of spinodal compositions can be calculated. Because the value of is very sensitive to experimental errors, an elaborate analytic procedure is required for

Jan 1, 1965

By Laurance Reid

HIGH compression ratios, resulting from high injection pressures and relatively low recovery process pressures, constitute a major problem, which has confronted those engaged in gas recycling for condensate production since the beginning of that practice. Despite the numerous process developments and improvements, no entirely satisfactory solution for this prob-lem has been presented to date. Often, where the residue gas from the recovery process must be recompressed for subsurface injection, there is a substantial difference between the required injection pressure and the plant-operating pressure required to produce maximum recovery of condensate. These limitations result in high compression ratios, which, in turn, neces-sitate excessive compressor investment and operating cost. As an alternative, the operating pressure may be increased in order to lessen the compressor requirements but such a saving often is purchased at the expense of decreased condensate recovery, caused by operation at the higher pressure. Regardless of the choice, the net result is a diminished return on the capital invested in the project. The goal of future development in this field must be the complete recovery of all valuable hydrocarbon components in the reservoir fluid at pressures that, regarded as compressor suction pressure, will require minimum compressor horsepower to inject the residue gas into the formation. A com-pression ratio of 1.5 has been established as an optimum for modern compressor equipment." Therefore, in order to con-form to this optimum condition, a 3000-lb. injection pressure would require that the condensate recovery process be operated at 2000 lb. per sq. inch.

Jan 1, 1940

By Edward L. Vickers

The Pacific rim countries, comprising more than half the globe, represent a complex mix of developed and developing nations. The area comprises a large segment of the industrialized world. Within its boundaries are also found many of the world's greatest mineral resources largely concentrated in the less developed countries. The conflicting objectives of these developed and developing nations are giving rise to changes in the traditional patterns of world resource development. Powerful political and socio-economic factors affecting the world today are having a great bearing on natural resource developments in the Pacific basin. New forms of partnerships have been emerging in developing nations which have had a great impact on the mining com- munity, lending institutions, as well as political relations. The United States and Japan have been substantially responsible in the past for the development of natural resources in this area of the world. Their role, however, is undergoing significant metamorphosis. The rapidly changing economic and social environment in the developing countries is producing new tensions which affect future collaboration between producers and users of natural resources. To understand current problems, I believe, it is worthwhile to examine historical trends in this area which may help defining alternatives facing us in the future. In modern times the United States was the first country in the Pacific basin to start development of resources on a massive scale. It began with the major exploration of the mineral-rich west of the United States and extended significantly later into Latin America and Australia. In the early 1950's, Japan became a significant

Jan 1, 1976

By C Gunther

The term metamorphism as commonly used means any change in a rock in either form or composition, from whatever cause. By metasomatism, according to Lindgren, is meant a metamorphism that involves a change in the chemical composition of a rock by the addition or subtraction of substance. Certain types of metamorphism are due to the action of mineralizing solutions, and are closely connected with ore deposition; they form, therefore, valuable guides in the exploration for ore-deposits. Other types of metamorphism are due to regional processes, and are not connected with ore deposition. By dynamo-regional metamorphism is meant a primary alteration of rocks over large areas under conditions of pressure, flow- age, and heat. This process produces schists and gneisses from either sediments or igneous rocks. It is thought that there is little migration of minerals or of elements in dynamo-regional metamorphism, and that the changes are due chiefly to recrysallization and rearrangement of original minerals in bands with their major axes oriented normal to the direction of greatest pressure. Under these conditions limestones are commonly altered to marble, and sandstones to quartzite, basic igneous rocks to greenstone or serpentine, while rocks of normal or acid com- position commonly yield the usual types of schist or gneiss. Dynamo-regional metamorphism, extending over large areas, has no connection with mineralizing processes, and is, therefore, no guide to ore deposits; while this process has certain features, such as characteristic mineral associations, in common with contact metamorphism, the results of the two processes may usually be distinguished without difficulty.

Jan 1, 1932

By Cyril Smith

IN the study of the structure or the properties of a series of alloys or nonmetallic compounds, it is often advantageous to express the com-position not as percentage by weight, according to which the material is always made up and analyzed, but as the atomic percentage of the two constituents. The conversion from the one to the other is repre-sented by the formulas: 100A 100x or 1 x/A+100-x/B B(100-x) _ 100yA 100y [2] X. yA + (100 - y)B or y (100 - y) where x and y are the weight and atomic percentages respectively of the element of atomic weight A, and (100 - x) and (100 - y) are the per-centages by weight and by atoms respectively of the element of atomic weight B. While calculations according to these formulas are simple, they are time consuming if several conversions have to be made. In 1931 Water-man1 constructed a nomograph for performing the conversion, but this did not permit an accuracy greater than about 1 per cent to be obtained in the neighborhood of 50 per cent. Ölander2 has proposed a graphic method simpler than Waterman's and one that gives a uniform precision throughout the entire scale. The possible accuracy is about 0.5 per cent of the whole, depending on the size and accuracy of the coordinate paper used. Recently, Hermann3 has described a slide rule for making the calculations. These devices make use of the simple rearranged equation

Jan 1, 1933

By Cyril Smith

IN the study of the structure or the properties of a series of alloys or nonmetallic compounds, it is often advantageous to express the com-position not as percentage by weight, according to which the material is always made up and analyzed, but as the atomic percentage of the two constituents. The conversion from the one to the other is repre-sented by the formulas: 100A 100x Y x 100 ? x/A A [1] A+ B x + A/B(100-x) X _ 100yA 100y [2] yA+(100-y)B or y+A(100-y) where x and y are the weight and atomic percentages respectively of the element of atomic weight A, and (100 - x) and (100 - y) are the per-centages by weight and by atoms respectively of the element of atomic weight B. While calculations according to these formulas are simple, they are' time consuming if several conversions have to be made. In 1931 Water-man' constructed a nomograph for performing the conversion, but this did not permit an accuracy greater than about 1 per cent to be obtained in the neighborhood of 50 per cent. Olander2 has proposed a graphic method simpler than Waterman's and one that gives a uniform precision throughout the entire scale. The possible accuracy is about 0.5 per cent of the whole, depending on the size and accuracy of the coordinate paper used. Recently, Hermann3 has described a slide rule for making the calculations. These devices make use of the simple rearranged equation:

Jan 1, 1933

By M. R. Tek, R. L. Nielsen

The scaling laws as formulated by Rapoport relate dynamically similar flow systems in porous media each involving two immiscible, incompressible fluids. A two-dimensional numerical technique for solving the differential equations describing systems of this type has been employed to assess the practical value of the scaling laws in light of the virtually unscalable nature of relative permeability and capillary pressure curves and boundary conditions. Two hypothetical systems — a gas reservoir subject to water drive and the laboratory scaled model of that reservoir — were investigated with emphasis placed on water coning near a production well. Comparison of the computed behavior of these par ticular systems shows that water coning in the reservoir would be more severe than one would expect from an experimental study of a laboratory model scaled within practical limits to the reservoir system. This paper also presents modifications of the scaling laws which are available for systems that can be described adequately in two-dimensional Cartesian coordinates. INTRODUCTION Present day digital computing equipment and methods of numerical analysis allow realistic and quantitative studies to be carried out for many two-phase flow systems in porous media. Before these tools became available the anticipated behavior of systems of this type could be inferred only from analytical solutions of simplified mathematical models or from experimental studies performed on laboratory models. To reproduce the behavior of a reservoir system on the laboratory scale, certain relationships must be satisfied between physical and geometric properties of the reservoir and laboratory systems. Where the reservoir fluids may be considered as two immiscible and incompressible phases, the necessary relationships have been formulated by Rapoportl and others.2-5 Rapoport's scaling laws follow from inspectional analysis of the differential equation describing phase saturation distribution in such systems. It will be recalled that these scaling laws presuppose three conditions: (1) the relative permeability curves must be identical for the model and prototype; (2) the capillary pressure curve (function of phase saturation) for the model must be linearly related to that of the prototype; and (3) boundary conditions imposed on the model must duplicate those existing at the boundaries of the prototype. These three requirements seldom if ever can be satisfied in scaling an actual reservoir to the laboratory system because: (1) The laboratory medium normally will be unconsolidated (glass beads or sand) while the reservoir usually is consolidated. Relative permeability and capillary pressure curves are usually quite different for consolidated and unconsolidated porous media. (2) The reservoir usually will be surrounded by a large aquifer which could be simulated in the laboratory only to a limited extent. (3) Wells present in the reservoir would scale to microscopic dimensions in the laboratory if geometric similarity is to be maintained. In view of these considerations, rigorous scaling of even a totally defined reservoir probably would never be possible. The purpose of this paper is to assess the practical value of the scaling laws in the light of the unscalable variables. This has been done by carrying out numerical solutions in two dimensions to the differential equations describing the flow of two immiscible, incompressible fluids in porous media for a field scale reservoir and a laboratory model of that reservoir. While both the reservoir and the laboratory model were purely fictional, each has been made as realistic and representative as possible. The field problem selected as the basis for the investigation was an inhomogeneous, layered gas reservoir initially at capillary gravitational equilibrium and subsequently produced in the presence of water drive. The laboratory model of this reservoir was designed to utilize oil and water in a glass bead pack. The numerical treatment employed was similar to that of Douglas, Peaceman and Rachford6 and it included both capillary and gravitational forces as

By John E. Willson, Ben L. Seegmiller

A portable electronic instrument was designed and constructed to detect unknown stress magnitudes in rocks. The principle used to detect stress is based on the propagation velocity method. This method allows the stress in a rock subjected to a load of unknown magnitude to be determined, provided that the wave velocity-stress relationship for similar rock is known. This is accomplished by measuring the travel time of longitudinal mechanical waves passing between two points a set distance apart in a rock. The velocity of the wave is calculated and the stress determined from the wave velocity-stress relationship. If the sending and receiving transducer spacing is constant, a time vs. stress relationship rather than the velocity-stress relationship may be used. The method is nondestructive and tests can be made without drilling or otherwise disturbing the rocks. The first studies undertaken in the United States to determine stress in rocks using propagation velocity techniques were reported by Obert1,2 in 1939 and 1940. The Soviet Union first reported using propagation methods to study rock pressures in 1951.8 Success of the method led to the development of a pulse-type ultrasonic seismoscope4 in 1953. Using this instrument, Ivanov and Betaneli5,6 in 1963 succeeded in devising and testing under field conditions a method of investigating coal pillar stresses. In 1967 Osipova7 reported results of similar studies in the Nakhichevan salt mines. In France, Tincelin8 has used the propagation velocity method to study the stress distribution in iron ore pillars. Uhlmann9 has investigated stresses in salt and potash pillars in Germany, using velocity techniques. Determination of uniaxial stress by propagation velocity methods is limited to rocks which have readily detectable wave velocity-stress variations. The present stress detection instrument is restricted in application to rocks which have a velocity change under stress of at least 300 fps. Examples of rocks which meet this requirement are sandstones, coal, and possibly some limestones. Testing of this instrument was limited to a laboratory study and the results may or may not be indicative of what would be found in a field test. A program of field experiments to study the feasibility of using this instrument to determine mine pillar and tunnel stresses is in progress. Instrument Design The instrument has two main components: A probe and a control-display unit. The probe is a hand-held device to which two identical rodlike transducers are rigidly mounted. Coaxial cable connects the probe to the control-display unit which is mounted in an enclosed carrying case measuring 7 % x 9 x 13 in. The instrument is designed so it may be carried and operated by one man. Weight of the probe and enclosed control-display unit is approximately 20.1b. The probe consists of two transducers identical in construction. One transducer is used to convert electronic pulses to mechanical waves and transmit these waves into a rock. The other detects the transmitted waves in the rock and converts them back into electronic signals. The basic element in both transducers is a piezoelectric crystal. The crystal is a disk made of lead titanate zirconate and has a natural resonant frequency of 400 kHz ±1% in the thickness mode. A schematic of one of the two identical transducing elements is shown in [Fig. 1.] A spacing of 6 in. between sending and receiving transducers has been found to be most satisfactory. The control-display unit consists of a pulse generator and a 1-in. oscilloscope. Various electronic devices are used for the power supply, amplification, and calibration. The amplitude of the square wave from the pulse generator can be continuously varied between 0 and +20 vdc. Pulse width can be set at 1, 2, 3, or 4 µsec. The repetition rate of the pulse can have the following values: 50, 75, 100, 150, 200, 250, 300, 400, 500, 750, and 1000 Hz. The oscilloscope delay system allows the travel time of the longitudinal wave passing through a rock to be measured to an accuracy ±0.1 µsec in the range from 0 to 995 µsec. Fig. 2 is a schematic of the various electronic sections in the control-display unit. Laboratory Testing The first step in using the instrument is to develop a velocity-stress or a time-stress curve for the par-

Jan 1, 1972

By Craig S. Hartley

Expressions are obtained for the energy changes associated with the reaction of (a& (111) slip dislocations on intersecting (110)planes in anisotropic bcc metals. An energy criterion for assessing the likelihood of dissociation of the products of such reactions is also presented. It is found that the "burrier reactions" which form a(100) dislocations at the intersection of two active {110) slip planes are more energetically favorable in metals which exhibit a high value of Zener's anisotropy factor, A, than those which have a low value. The results are presented in a form which permits the stacking fault energy to be obtained from a measurement of the separation between par-tials in a dissociated configuration. However, until accurate calculations or measurements of the stacking fault energies involved are available, it is not possible to assess the physical importance of dissociated dislocations. In a recent paper,' the energy changes associated with several types of reactions between two slip dislocations, (a/2)(111){110), in bcc structures were calculated.* Isotropic elasticity and the approxima- tion v = -3- were employed. The purpose of this work is to present calculations of the energy changes for many of the same reactions using anisotropic elasticity. The problem of dissociation of a(100) and a(110) dislocations is also considered, and maximum fault energies for which dissociation will be energetically favorable are calculated for several bcc metals. Two general types of reactions are considered; those for which the reactant (a/2)(111) dislocations have long-range attractive forces and those for which the reverse is true. An example of the former is: (a/2)[lll] + (a/2)[lll]-a[l00] while the latter are typified by: (a/2)[lll] + (a/2)[111] -a[011] Only reactants lying in different slip planes are considered; therefore, the products must lie along (111) or (100) directions, which are the intersection of two {llO} planes. It will be assumed that the reactants and products are infinitely long parallel dislocations, since in this case the energy change associated with the reactions is a maximum.' THEORY The self-energy per unit length of a straight mixed dislocation in an anisotropic medium can be written? where b is the Burgers vector, K is an appropriate combination of the single-crystal elastic constants, and R and ro are, respectively, outer and inner cut-off radii of the elastic solution. The energy given by Eq. [I] does not account for any variation of the core energy with orientation. This could be manifested by an orientation dependence of the core radius or, equivalently, the Peierls width, of the dislocation. However, the energy contribution due to this source is expected to be small, and current models of the dislocation core are not sufficiently accurate to justify such a refinement. It has already been shown that for the isotropic case the energy contributions due to nonzero tractions across the cores of the reactants and products exactly cancel one another in the reaction.' Accordingly, it will be assumed that this contribution to the total energy change in the anisotropic case is small. In the subsequent discussion it is also assumed that the core radii of the reactant and product dislocation are the same and that, where stacking faults are formed, the faulted region is bounded by the centers of the partials. Consequently only changes in elastic energy due to the reactions will be considered. When the dislocation is parallel to either the (111) or the (100) directions, K may be written:375 K = (Ke sin2 a + Ks cos2 a) [2] where K, and Ks are the combination of elastic constants corresponding to an edge and screw dislocation lying along the same direction as the mixed dislocation, and a is the angle between the direction tangent to the dislocation line and the Burgers vector. Eq. [2] should not be confused with the isotropic approximation to the variation in energy with line Orientation.6 It should be noted that the essentially isotropic expression for K is a result of the characteristic symmetry of the (111) and (100) directions and is not, in general, valid for other dislocation directions in anisotropic cubic metals. The energy* change for a reaction in which the re- actant and product dislocations are parallel perfect dislocations can be written: where Ep and E, refer to the self-energies of the products and reactants, respectively. For dislocations parallel to (100) and (111) directions, Eq. [3] becomes:

Jan 1, 1969

By A. D. Rovig, D. W. McGlashan, Donald M. Podobnik

Crystal-chemical and stntctural properties of sulfide minerals are considered. The information gained is to be used to interpret (I ) freshly broken mineral surfaces, (2) modifications of the mineral surfaces, and (3) reactions at the mineral surfaces. From these basic disciplines, concepts with regard to the changes that surfaces undergo, reactions that might take place, the geometry of the interface, the state of different atoms and ions in the interface, and other physical and chemical properties of an interface must be developed, weighed and applied. The authors first deal with these conceptual considerations from which hypotheses are set forth to describe the environ men tal-interfacial relationships for several sulfide minerals. Qualitative and quantitative explanation of par-ticulate solid separations are unknown entities because of the lack of adequate models and mathematical relationships to explain the activity occurring between the solid and liquid phases. It is a transitional region in which it is difficult to ascertain the mechanisms of adsorption of ions, molecules, etc., on mineral surfaces, as well as other secondary reactions which occur in interfacial regions. Thus, in this paper the authors deal with conceptual considerations from which hypotheses are set forth to describe the environmental-interfacial relationships for sulfide minerals. GENERAL CONSIDERATIONS Interfacial Reactions:Interfacial reactions are the cruxes of flotation schemes as well as other processes such as thickening, filtration and hydrometallurgy. However, as noted by Klassen and Mokrousov: 1 "The problems concerning the surfaces of natural minerals, the laws governing simultaneous adsorption from aqueous solution on these surfaces of a whole series of reagents, the laws of the surface reactions and the properties of water layers separating the minerals, are all known to a first approximation only." An investigator has the privilege of postulating methods of solid-liquid interfacial reactions. REACTIONS WITH WATER - Water consists of hydronium (H3 O 4) and hydroxyl (OH-) ions in the ionized state. That this is so forms the basis for the postulated reaction of the hydrated hydrogen ion with net-negative mineral surfaces as depicted in Fig. 1. In this case water is bonded to mineral surfaces through hydrogen-bridge-type bonds - possibly hydrogen bonds. Although bonding of the van der Waal type may be responsible for this reaction, it is most likely that stronger bonds are involved. Once firmly bonded to the surface, the water layer is known to be quite tenacious. It is further speculated that a shear plane exists at some distance (see Fig. 1) away from the mineral surface. Exact location of this plane is not known, but in all probability it will be positioned across a weak bond of the hydrogen-bond type where the surface-attached water is coordinated to the original hydrated hydrogen ion. REACTION WITH METAL IONS - Klassen and Mokrousov ' state: "The presence of an ion in water leads to an immediate formation around that ion of a highly condensed atmosphere of water dipoles and thus to hydration of the ion." The fact is known that multivalent cations are strongly hydrated, usually by six or eight molecules of water, and that anions are not so strongly hydrated. Conceding the fact that thermodynamics, concentration, pH, and physical considerations are of utmost importance in truly explaining a mechanism of metal ions reaction with a hydrated mineral surface, it does seem logical that the mechanism illustrated in Fig. 2 is feasible. In this reaction, the metal ion (M) is coordinated in one dimension - to the mineral-surface hydration layer. Note also that explanation of this reaction requires that the shear plane move to a less stable bond configuration; that is, the shear plane has moved to a position between the metal ion and the other coordinated water molecules which are more free to dissociate. Reactions as depicted in Fig. 2 should cause the formation of an apparent mineral surface which is net-positive. Immediately, it must be noted that measurements of apparent-mineral surfaces serve - within limits - to indicate a degree of ion-surface reaction capability. The major limiting factor he re is one related

Jan 1, 1970

By H. B. Probst

Mechanical twins were produced in zone-refined tungsten single crystals by explosive working at room temperature. These twins are parallel to (112) planes and have irregular boundaries rather than the classical plane twin boundaries. These boundaries aye grooved surfaces in which the grooves themselves are parallel to a <111> direction and the sides of the grooves appear to be par-allel to (110) planes. TWINS were produced in tungsten single crystals by explosive working at room temperature. These twins differ in character from any previously reported for tungsten; however, they are similar to those found in molybdenum after compression at -196°C.1 Deformation twins "resembling Neumann bands in ingot iron" have been observed in tungsten by Bech-told and Shewmon.2 This observation was made with sintered polycrystalline tungsten pulled in tension to fracture at 100°C and using a strain rate of 2.8 x 10-4 sec-1. More recently Schadler3 found deformation twins in zone-refined tungsten single crystals pulled in tension at -196"&apos; and -253°C. These tests were conducted using a strain rate of 3.3 x l0-4 sec-1, and the twin bands were found to be parallel to a (112) plane. Deformation twins in tungsten&apos;s sister metal, molybdenum, were observed by Cahn.4 These twins were produced by compressing small (0.7 mm) vapor-deproducedposited molybdenum single crystals at -183°C. The compression was performed &apos;by impact." By the use of precession X-ray techniques, Cahn was able to identify the twin plane as {112} and the shear direction as <1ll>. Mueller and Parker1 produced deformation twins in polycrystalline electron-beam-melted molybdenum by compression at -196°C. Their "loading rate" was 5000 psi per min which, judging from their stress-strain curve, corresponds to a strain rate of approximately 0.3 x 10-4 sec-1. These twin bands were found to be parallel to (1 12) planes; however, they differed in appearance from previously observed twins. In place of straight and parallel twin boundaries they were found to be irregular, jagged, and sawtoothed. The sides of the saw teeth were identified as (110) planes and irrational planes of a (111) zone. The twins observed in the present work in tungsten single crystals are similar in appearance to those of Mueller and Parker in polycrystalline molybdenum. The starting material used in this investigation was 3/16-in. diam commercial tungsten rod produced by powder-metallurgy techniques. This material was converted to a single crystal by the electron-bombardment floating-zone technique.= The process was carried out in a vacuum of 10-5 mm of Hg using a traversing speed of 4 mm per min. Segments (=2 in. long and 3/16 in. in diam) of two crystals (A and B) produced in this manner were studied. Crystal A received one zoning pass, while crystal B received two passes. The two crystals were explosively worked at Bat-telle Memorial Institute in the following manner. A 1/2-in.-thick layer of plastic was applied to the crystals to serve as a buffer in an attempt to prevent cracking. The composite, crystal and buffer, was then wrapped with 1/8-in.-thick DuPont sheet explosive EL506A2 and detonated in water at room temperature. Metallographic samples of the worked crystals were prepared, and back-reflection Laue X-ray patterns were obtained using unfiltered molybdenum radiation. RESULTS AND DISCUSSION Blasting the crystals as described above failed to prevent cracking. The crystals fractured into several fragments about 3/16 to 1/2 in. long; however, the fragments were of sufficient size to be useful for the subsequent study. The diamond pyramid hardness of the crystals after blasting was in the range 430 to 450 as compared with 340 for the as-melted material, which shows a definite hardening resulting from plastic deformation. These hardness values were obtained using a 1000-g load and taking readings only in sound portions of the crystals free of cracks. The crystals exhibited profuse twinning as shown in Fig. 1. No such structure is present in the as-melted condition. Most of these twins have jagged twin boundaries and are similar in appearance to those found in molybdenum by Mueller and Parker. The twins in both crystals were found to be parallel to {112} planes. This identification was made by using the conventional two-trace method. Subsequent efforts to describe these twins more fully were carried out on crystal A. If the longitudinal axis of crystal A is placed in the (001)-(011)-(Il l) basic triangle of the standard cubic stereographic projection, as in Fig. 2, then the two sets of twins shown in Fig. 1 are parallel to the (112) and (121) planes. Fig. 3 shows a schematic representation of a twin with jagged boundaries. This type of twin with a <111>

Jan 1, 1962

By Donald B. Evans, Robert D. Pehlke

The solubility of nitrogen in liquid Fe-A1 alloys has been measured up to the solubility limit for formation of aluminum nitride using the Sieverts method. The activity coefficient of nitrogen decreases slightly with increasing aluminum content in the range of 0 to 4 wt pct Al. Based on a nitride composition, AlN, the standard free energy of formation of aluminum nitride from fhe elements dissolved in liquid iron has been determined to be: ?F" = -59,250 + 25.55 T in the range from 1600º to 1750ºC. The solubility of nitrogen in liquid iron alloys and the interaction of nitrogen with dissolved alloying elements in liquid iron have been the subject of a number of research investigations.&apos; Most of this work, however, has been reported for concentrations well below those necessary for the formation of the alloy nitride phase. Data in the concentration region near the solubility limit of the alloy nitride, particularly for systems exhibiting stable nitrides, are important in evaluating the denitrifying power of various alloying elements. They are also useful in determining the stability of a given nitride if it is to be used as a refractory to contain liquid iron alloys. In view of the importance of aluminum as a deoxidizing agent in commercial steelmaking and the fact that its nitride, AIN, is a highly stable compound and has merited some consideration as an industrial refractory, the following investigation was undertaken. The use of the Sieverts technique provided a measurement of the equilibrium nitrogen solubility in liquid Fe-A1 alloys as a function of nitrogen gas pressure up to 3.85 wt pct A1 in the temperature range of 1600º to 1750°C. The values obtained by the Sieverts method were checked by means of a quenching method in which liquid iron was equilibrated with an A1N crucible under a known partial pressure of nitrogen gas, and the solubility of A1N in liquid iron determined by chemical analysis. EXPERIMENTAL PROCEDURE The theoretical considerations involved in determining the solubility product of a solid alloy nitride phase in liquid iron by measuring the point of departure of the nitrogen gas solubility from Sieverts law have been discussed by Rao and par lee.&apos; The principal problem is to determine the variation of nitrogen solubility in an alloy as a function of the pressure of nitrogen gas over it with sufficient precision to establish the break point in the curve at the solubility limit of the alloy nitride phase. A fairly large number of data points are required to do this. A second problem is the determination of the composition of the precipitated solid nitride phase. This is necessary in order to define completely the thermodynamic relationships. The Sieverts apparatus used to make the nitrogen solubility measurements in this investigation is of essentially the same design as that described by Pehlke and E1liott.l The charge materials were Ferrovac-E high purity iron supplied by Crucible Steel Co. and 99.99+ pct pure aluminum. Recrystal-lized alumina crucibles were used, and were not attacked by the liquid alloys. The hot volume of the system which was measured for each melt ranged from 46 to 50 standard cu cm and was found to decrease linearly with decreasing pressure and with increasing temperature. The temperature coefficient of the hot volume at 1 atm pressure of argon gas was essentially constant for all experiments at a value of -6 X 10-3 cu cm per "C. The melt temperature was measured with a Leeds and Northrup disappearing filament type optical pyrometer sighted vertically downward on the center of the melt surface. The temperature scale was calibrated against the observed melting point of pure iron taken as 1536°C. The emissivity of all melts was assumed to be that of pure iron, taken as 0.43. The charge weights ranged from 110 to 140 g and the range of aluminum contents covered was from 0 to 3.85 wt pct. Aluminum additions were made as 12 to 15 wt pct A1-Fe master alloys previously prepared in the system under purified argon. The compositions of the master alloys were checked by chemical analysis and found to be in agreement with the charge analyses. Vertical cross sections of the master-alloy ingots were used as charge material for the equilibrations in order to minimize the effect of any segregation which might have occurred during solidification of the master alloys. Determinations of the solubility product of

Jan 1, 1964

By Carroll F. Hardy

The day by day loss of industrial plants to gas and oil is chiefly by default. The coal industry is not selling its superior economy, safety, and other advantages to its customers. THE position of the coal industry has been affected by a wide variety of developments in the production and use of energy. The tempo of development and change has been increasing and the end is not in sight. Legislation is currently being proposed for commercial use of atomic power, and the employment of atomic energy in significant quantity will probably occur about the same time as the decline in production of petroleum and natural gas. But these developments are in the future and have little immediate effect on utilization and marketing of coal. While no one should try to suppress or retard the development of a new and economical source of energy, both the coal and private utility industry should be allowed to question how the nuclear power is to be used, who is to use it, and who is going to pay for it. The taxpayers have a monopoly on fissionable material and the knowledge to employ it. Any commercial use must stem from this source. It is not hard to visualize either taxpayer-subsidized private utility atomic power plants on one hand and super TVA&apos;s on the other. In view of the gains of gas and oil in the home heating field, it is interesting to compare the 1940 and 1950 census reports on the kind of fuel used for heating in occupied dwelling units. Table I shows that whereas coal provided 77 pct of the fuel for central heating (furnaces and boilers) in 1940, it was down to 45.4 pct in 1950. However, only about 1 1½ million units were lost in this 10-year period. In the non-central heating category, which principally includes stoves, the percentage declined from 39.2 to 25.6, but the units declined about 2½ million in number. The big increase was in heating units designed to burn gas and oil. Use of wood for central heating declined about one-third. Data on amount of fuels used for residential heating are not available, but information is on hand for residential and comnlercial space heating, see Table 11. Commercial space heating includes office buildings, churches, schools. and similar structures. The annual use of bituminous coal in these two categories declined about 1 million tons in the 10-year period. Other forms of solid fuel showed greater losses, except wood, which remained the same. Domestic stokers reached their high point in 1948 with about 1,200,000 in use. At the end of 1951 there were approximately 1,116,790 stokers in use. Conversions to gas and oil have been from hand-fired heating plants in the ratio of about 7 to 1 compared to stokers. In other words, for every one stoker which has been converted to gas or oil, seven hand-fired units have been converted to gas or oil. A bare recital of these data would indicate that the coal industry is holding its own reasonably well. However, 93.4 pct of the new homes built in 1951 were heated by gas or oil. Oil-burning equipment was installed in 37.8 pct and gas equipment in 55.6 pct of the new homes. This indicates that the public prefers gas when it is available, and that oil is second choice, with all forms of solid fuel apparently used when it is unavoidable. It must be pointed out, however, that during the period of rapid expansion of gas pipelines gas has been sold for house heating at prices that are in some cases actually lower than coal prices, or very nearly on a par. Gas has been sold at wells at far below the comparable price for oil produced from the same wells, and far below its actual worth. This situation is being remedied at the present time by increases in gas prices at the wells. For example, the wellhead price of gas in Texas averaged 7.494 per Mcf in 1952. In 1949 it was 4.59c per Mcf. This increase in price is being reflected in pipeline gas prices, and in most of the markets served by the pipelines the tendency is to get it out of the bargain basement type of sales. The American Gas Association estimates that at the end of 1952 there were in the United States about 11 million customers for gas house-heating, and the Association expects additional gains each year until around 18 million homes will be heated by gas in 1975. By 1975 there should be 60 million dwelling units to be heated in the United States, if dwelling units increase at the same rate as the population. If the gas industry heats 18 million dwelling units by that time, this still leaves 42 million units to be heated by some other fuel. If oil is used to heat 18 million dwelling units in that same year, 24 million would of necessity be heated by coal, coke, wood, electricity, or another fuel. The total number of dwelling units using coal listed in the 1950 Census was 18,776,000, so it would appear that coal has a chance at least to stand still in the tonnage sold for domestic use. In the first quarter of 1953, 2044 domestic stokers

Jan 1, 1955

By J. M. Oblak, W. A. Owczarski

A cellular appearing recrystallization product formed by annealing a cold-worked nickel-base super-alloy at 1800°F has been studied by electron nzicroscopy. Prior to deformation, an equilibrium micro-structure of fcc matrix y and cuboidal ,,&apos;, Ni (Al, Ti), precipitates of CuzAu structure had been established by an age at 1825°F. The strain-free recrystallization cells consist of very large rodular y&apos; particles in a y matrix. They precipitate is oriented and coherent both before and after recrystallization. The results showed that y&apos; coarsening accompanies recrystallization at 1800°F. However, it does so as a secondary effect and does not necessarily take place at lower temperatures. The structural similarity of this reaction to cellular precipitation in other systems indicates that lattice strain may also play a significant role during some cellular precipitation reactions. THERE have been numerous microstructural investigations of recrystallization in single-phase materials but two-phase systems have received much less attention. The second phase can either remain inert or be altered along with the matrix during recrystallization. If the second phase is an oxidelm3 or a relatively inert pre~ipitate,~, recrystallization is retarded when the interparticle spacing is less than 1 p. Prior to the onset of recrystallization, these materials show a well-polygonized substructure with the subgrain size limited by the interparticle spacing. Since recrystallization by the motion of preexisting grain boundaries6 is not observed, retardation has been related to particle pinning of the subboundaries. This pinning prevents coalescence&apos; or growth8 of subgrains to a critical size (formation of a high-angle boundary) necessary to initiate recrystallization. In a material such as a nickel-base superalloy both y matrix and y&apos; precipitate are altered by the recrystallization reaction. Haessner et al.&apos; studied the recrystallization of a cold-rolled Ni-Cr-A1 alloy by electron microscopy. The material was initially cold-rolled in the supersaturated condition. upon annealing at 750°C, immediate precipitation of 7&apos;occurred. Presence of this 7&apos; greatly retarded the onset of recrystallization which eventually took place by the development of randomly oriented, strain-free grains. The original •/ was dissolved at the recrystallization interface and reprecipitated as oriented, coherent par-tiles in the new grain. Recrystallization caused a refinement of .)&apos; particle size. Recently ~hillips&apos;&apos; investigated recrystallization of Ni-12.7 at. pct Al. Reduction by cold rolling presumably elongated the p&apos; precipitate into lamellae that remained coherent with the matrix. After recrystallization at 600" to 750°C, there was no unusual change in y&apos; particle size al- though there was a tendency toward clustering along the prior rolling direction at 750°C. Above 750°C, the recrystallized grains were generally free of precipitate. Studies in the somewhat analogous Cu-3.23 wt pct CO" and Cu-2 wt pct&apos;2 systems demonstrated that the coherent cobalt-rich fcc precipitate in these alloys obstructed softening, initiation, and completion of recrystallization. The precipitates were deformed into lam~llae during rolling and those of diameter less than 250A remained coherent. Recrystallization took place by the growth of new grains into the recovered or poly-gonized material. In the first study," both matrix and precipitate reoriented in the same manner upon passage of the recrystallization interface. There was no change in particle size or morphology. Tanner and ~ervi,~ on the other hand, observed that motion of the recrystallization fronts was strongly hindered by the pinning action of coherent precipitates in the deformed material. Particles in contact with a pinned boundary coarsened and coalesced leaving a denuded zone in the unrecrystallized region. When the number of pinning points was sufficiently reduced by coalescence, the boundary swept past these particles and through the denuded zone. The authors1&apos; considered this as a variation of discontinuous precipitation with both chemical driving force and deformation strain energy contributing to recrystallization. Preliminary observations by the present authors had revealed that recrystallization in Udimet 700, a nickel-base superalloy, occurred in an entirely different manner. Optical metallography showed that the recrystallized product formed as cellular colonies containing coarse y&apos; particles elongated in the direction of cell growth. In this investigation the structural features of this reaction were investigated by transmission electron microscopy. EXPERIMENTAL PROCEDURE As-received I$-in. rounds of Udimet 700* were (wtpct) 18.4 15.2 4.95 4.42 3.43 0.06 0.031 0.14 Bal. solution-annealed for 4 hr at 2150" and then fast air-cooled. An initial y-~&apos; structure was established by a 4-hr age at 1825°F followed by a fast air,cool. Essentially the equilibrium volume fraction of ?&apos; at 1825°F is precipitated within 4 hr. Microstructural examination showed no measurable increase in the amount of precipitate after longer aging times. Deformation consisted of swaging to 52 pct RA with 6 pct reduction per pass at room temperature. To reduce the precipitation potential to a negligible amount, recrystallization anneals were conducted at 1800"~ (982"~). Microstructures were investigated by optical and transmission electron microscopy. To prepare foils for electron microscopy, the material was first sliced into 30-mil slabs parallel to the swaging direction. Discs were dimpled and electrolytically cut from

Jan 1, 1969

By C. G. Dunn, J. L. Walter

The c/laracterzstics of cube-oriented nuclei ard other matrix grains that are associated with secondary, recrystallization to the cube texture in high-purity silicon iron were investigated by me-tallographic and X-ray methods. The results show that the structure consists of relatively perfect grains of average diameter between one and two times the sheet thickness ad that the texture has a moderately strong (110) [001] component and a weak (100) [001] component. The results also indicate that matrix stability results from the two-dimensional nuture of the graitzs and that cube-orzented nuclei are neither more Perfect nor larger grains than other matrix grains but have a preferred [001] direction in the rolling direction and have a more effective driving force for growth than other grains because of a low (100) surface energy. THE structures and textures of fine-grained rnatrices determine to a large extent the kinds of secondary recrystallization textures that form on annealing. The understanding of secondary recrystallization processes therefore depends on adequate information about the initial matrices. Matrices usually have three characteristics: 1) they consist of fine-grained primary recrystallization structures, 2) the fine-grained structures are stable toward normal grain growth, and 3) they contain secondary recrystallization nuclei. Stability toward normal grain growth may be due to either a strong single orientation texture (texture inhibition)&apos; or a dispersed second phase (dispersed phase inhibition).2"4 If normal grain growth is not inhibited by either of these two factors, it nevertheless stops when the average grain size is between one and two times the sheet thick- ness.5 This thickness effect satisfies one of the characteristics of a matrix for secondary recrystallization. Its importance in the development of the cube texture in high-purity silicon iron by secondary recrystallization was pointed out by the authors in a recent paper on tertiary recrystallization7 and will be discussed further in the present paper. Assmus, Detert, and he8 have provided some information on a matrix for secondary recrystallization to the cube texture in silicon iron. They found a (110)[001] or Goss texture with enough spread about the rolling direction to include a small amount of the (100)[00l] orientation. The distribution of the [00l] directions was strongest parallel to the rolling direction for both (100) primaries and cube secondaries. These authors found no correlation between size of a matrix grain and orientation and concluded that some property other than size must be the distinguishing characteristic of the cube-oriented nucleus. No consideration was given, it

Jan 1, 1961

By Helmut Thielsch

MeTallographic specimens whose surfaces are to be investigated are too thick to allow either light or electrons to pass through them for microexamination by transmission. This difficulty is overcome with optical microscopes by illuminating the surface through the objective lens. For electron microscopes best results are obtained by preparing thin replicas of the surface of the specimen, placing them in the microscope and passing the electron beam through them. Since electron microscopes represent a rather recent invention, they have found little application as compared with optical microscopes. This is true because, aside from the cost of new equipment and development of new techniques, some of the older replica methods necessitated the destruction of the surface from which a thin transparent replica was obtained. In other processes in which the surface is preserved, either too tedious a procedure is required, unsuited to "mass-production" requirements of industrial laboratories, or replicas of insufficient contrast and sharpness are produced. In general, investigations with the electron microscope involve five steps: (I) polishing the surface of the metal specimen, (2) proper etching of the surface, (3) preparing the suitable replica from the surface, (4) examination and phorography in electron microscope and (5) interpretation. Preparation of Metal Surfaces Usual metallographic polishing is generclly satisfactory. It is important though that the final polish be applied very carefully, since otherwise evidence of a small amount of deformation might show up even on relatively deeply etched surfaces. A high-power microscope should be used to determine the suitability of the polish and etch. This, of course, is not different from optical examinations, but in these, if a deep etch is used, the problem is less serious. It is frequently difficult to detect with optical microscopes poor polishing aside fiom superficial scratches before etching. Figs. I and 2 show micrographs of "well" and "poorly" polished nickel etched by immersing the sample for 20 min. in a solution containing 8 grams cupric sulphate in 40 C.C. of concentrated HCl and 40 C.C. of Hz0 (Marble&apos;s reagent). The sample shown in Fig. I was polished in its final stages for 5 min. on a carborundum wheel followed by ro min. on a rouge wheel, whereas the sample shown in Fig. 2 was polished only I min. on the rouge wheel. Generally, this procedure does not guarantee that the surface of the specimen will be either undistorted or deformed. It was applied here merely to show the effects Of good and poor polishing. To the experienced investigator, plastic deformation is

Jan 1, 1946

By Helmut Thielsch

MeTallographic specimens whose surfaces are to be investigated are too thick to allow either light or electrons to pass through them for microexamination by transmission. This difficulty is overcome with optical microscopes by illuminating the surface through the objective lens. For electron microscopes best results are obtained by preparing thin replicas of the surface of the specimen, placing them in the microscope and passing the electron beam through them. Since electron microscopes represent a rather recent invention, they have found little application as compared with optical microscopes. This is true because, aside from the cost of new equipment and development of new techniques, some of the older replica methods necessitated the destruction of the surface from which a thin transparent replica was obtained. In other processes in which the surface is preserved, either too tedious a procedure is required, unsuited to "mass-production" requirements of industrial laboratories, or replicas of insufficient contrast and sharpness are produced. In general, investigations with the electron microscope involve five steps: (I) polishing the surface of the metal specimen, (2) proper etching of the surface, (3) preparing the suitable replica from the surface, (4) examination and phorography in electron microscope and (5) interpretation. Preparation of Metal Surfaces Usual metallographic polishing is generclly satisfactory. It is important though that the final polish be applied very carefully, since otherwise evidence of a small amount of deformation might show up even on relatively deeply etched surfaces. A high-power microscope should be used to determine the suitability of the polish and etch. This, of course, is not different from optical examinations, but in these, if a deep etch is used, the problem is less serious. It is frequently difficult to detect with optical microscopes poor polishing aside fiom superficial scratches before etching. Figs. I and 2 show micrographs of "well" and "poorly" polished nickel etched by immersing the sample for 20 min. in a solution containing 8 grams cupric sulphate in 40 C.C. of concentrated HCl and 40 C.C. of Hz0 (Marble&apos;s reagent). The sample shown in Fig. I was polished in its final stages for 5 min. on a carborundum wheel followed by ro min. on a rouge wheel, whereas the sample shown in Fig. 2 was polished only I min. on the rouge wheel. Generally, this procedure does not guarantee that the surface of the specimen will be either undistorted or deformed. It was applied here merely to show the effects Of good and poor polishing. To the experienced investigator, plastic deformation is

Jan 1, 1946

By H. D. Dahl, P. C. Thakur

This paper presents an analysis of a new tool for improved productivity in coal mining: the horizontal drilling system developed by Conoco/Consol. The analysis includes a brief description of the system; discussion of the three categories of advance exploration application of horizontal boreholes; and a survey of other special mining methods planned around long horizontal boreholes.

Jan 1, 1983

By K. H. Nimerick, G. P. Laflin

Laboratory data and field tests indicate that substantial losses of valuable coal can be caused by wind erosion. Wind tunnel tests show the effects of wind velocity and particle sizing on the amount of coal lost while in transit. Different coals were evaluated to determine the variables associated with wind erosion. The erosion losses can be substantially reduced by using a binder, or crusting agent, to consolidate the surfaces of the coal into a solid mass which resists erosion. This not only reduces economic loss but minimizes pollution.

Jan 8, 1979

A. A. Almstrom is mill superintendent for Barrue Mines, Barraute, Quebec. Frank A. Ayer, vice president of Copper Range Co., who has been in charge of the development and bringing into production of White Pine orebody in northern Michigan, has resigned. E. G. Bailey and H. S. Mudd were made honorary members of the American Society of Civil Engineers. Lee Bilheimer, graduate of Missouri School of Mines, has been employed as assistant mine captain at the Edwards, N. Y., div. of the St. Joseph Lead Co. Douglas C. Blackwell, recently graduated from the South Dakota School of Mines, is now with the Oliver Iron Mining Co. of Duluth, Minn. Joseph F. Brown has joined the Grand Junction Exploration Branch of the United States Atomic Energy Commission as a geologist.

Jan 1, 1952