Search Documents

By O. K. Miniato, L. Massé, K. Nobe, J. S. Aronofsky, W. F. 213-000-000-016 Seyer

MUCH work has been done dealing with the effect of mechanical stress on electrode potential in an electrochemical system. The contradictory nature of the experimental results indicates the complexity of the problem although thermodynamic considerations show that a simple relationshir, should exist. In those systems where a gas was the electromotive active substance satisfactory agreement between theory and practice has been found. Des Coudres' found this to be so even when the active substance of the electrode, in this case mercury, was in the liquid state. In contrast, attempts to correlate theory and experiment for the solid state have met with a very limited success. The early workers in this field, Andrews,2 Walker and Dill3 used iron, certainly one of the most reactive of metals. Others have made use of less active metals such as copper and nickel. Recently Fryxell and Nachtrieb4 investigated the electrochemical behavior of gold and silver under both tensile and compressive stresses and concluded that it was doubtful whether true stress potentials could ever be measured. Much of the lack of success to measure the thermodynamic stress potential can be ascribed to the presence or formation of a complex film on the metal surface in contact with the electrolyte. Further, the theoretical stress potential is very small and therefore difficult to measure directly. Thus the calculated emf between a 24 B & S gage cold-drawn copper wire stressed with a weight of 1 kg and an unstressed portion of the same wire is only 2.60 X 10"7 volts. This is very small compared to that which can be produced by chemical reactions at the metal electrolyte interface which in turn can be so large as to mask completely the stress potential. Hence in this type of measurement all chemical side effects must be eliminated or reduced as much as possible. It was for this reason that the system copper-sodium chloride solution was selected for study. INSTRUMENTATION In the many preliminary experiments conducted, two major difficulties were encountered. The first was to measure the small electro-potentials to be expected and the second to obtain a suitable electrode surface. The conventional potentiometric method was found to be unsatisfactory for measuring the small emf expected. However, by using an L & N No. 2290 galvanometer having a resistance of 915 ohms consistent measurements were possible. The reference electrode was always the unstressed one made from the same sample of wire. The steady current flow was approximately 10-8 amp. Lewis and Randell5 have stated that for currents of the order of 10-8, if there is no sensible polarization, the measured emf may be taken as a reversible one. To check the galvanomenter readings an alternative method was devised to measure the potential difference between the wires. This involved a Liston-Falb d-c breaker amplifier model 10, an L & N k-2 potentiometer and a moving-coil galvanometer having a sensitivity greater than 0.1 µv (microvolt) per mm. To increase further the output voltage of the amplifier a d-c amplifier, model B. L.-932 was introduced into the circuit. This amplifier was in turn connected to a Brush recorder which had been calibrated previously by the test signals from the Liston-Falb instrument. These test voltages employed took into account the impedance of the input current. Unfortunately, this method had too low a sensitivity for measurement below 10 µv. Above this value the voltage agreed reasonably well with those obtained directly by the simple galvanometer method. The main advantage of the amplifier setup was that one did not have to wait until no deflection occurred on the galvanometer in the circuit when first exposing the wires to the solu-

Jan 1, 1959

By Gerald Edmunds

Castings of pure metals and many alloys usually have a coarse-grained structure characterized by long columnar grains throughout the main body of the casting. Frequently, the surface exhibits finer, sometimes nearly equiaxed grains, and such grains may also compose other parts of the casting. This paper deals .primarily with determinations of the grain-orientation textures of the columnar and surface grains of polycrystalline zinc castings. It includes some results upon a cadmium casting and a magnesium casting. A hypothesis is developed to account for the observations on columnar grains and to use as a basis for predicting orientations in other cast metals. A general description of the position of the columnar grains in castings is that their long axes are approximately parallel to the direction of the thermal gradient during crystallization. Thus, in cylindrical castings the columnar grain axes tend to be radial, and in large flat castings where most of the cooling is through one or both of the large mold surfaces they tend to be perpendicular to the mold surfaces. At the edges and corners the direction of heat flow and therefore the position of the grains is more cornplex. Actually observation shows that even in castings made in flat molds the cooling seems to be somewhat irregular, since columnar grains tend to emanate from certain areas of the cooling surface, indicating that thermal contact was better there than in neighboring areas. The nucleus from which a columnar grain grows may be so oriented that its direction of maximum growth rate does not coincide with the direction of the thermal gradient. In this case the long axis of the grain probably assumes an intermediate position. Notwithstanding these minor irregularities, the situation does exist that the long axes of the columnar grains are generally disposed approximately perpendicular to the mold surface. Schmid and Wassermanl and Nix and Schmid2 have determined the orientation texture of columnar grains in castings of several cubic, tetragonal, hexagonal close-packed and rhombohedra1 metals. For zinc and cadmium, they report the basal plane to be parallel to the columnar grain axes, with no preference for any particular direction in this plane to coincide with the grain axes. This texture, termed a ring fiber texture,3 is uncommon in metals; zinc and cadmium are the only ones reported to exhibit it. Generally, it is stated, a simpler texture exists in which a principal, though not necessarily the most closely packed, crystallographic direction is parallel to the direction of heat flow. In cast magnesium (also hexagonal close packed) they report a digonal axis I, [100] direction, parallel to the direction of heat flow. The writer is not aware of any other orientation-texture determinations on cast polycrystalline hexagonal metals. In view of the observations reported in the present paper it is of interest also to note that Nix and Schmid stated that a

Jan 1, 1941

By Charles E. Parsons

One of the greatest factors in our industrial development is cheap and convenient power. Long-distance electrical transmission has now reached such a stage that it is feasible, and practicable, to utilize the water-power of the country which was heretofore too remote for consideration. In all of the changes of energy from its various sources to its electrical applications, water-power stands pre-eminent in point of economy. Power-users the world over have endeavored to utilize this force in preference to any other, and until long-distance transmission was found practicable it seemed that every available water-power in this section of the country was doing its full share for the benefit of mankind. The success of each great industrial development has been clue in a greater part to some one man one who is just a step in advance of the rest in his particular field; one who is able to grasp a situation and foresee possibilities; and, above all, one who has that indomitable pluck and perseverance which sees in each obstacle one more step toward success. Such a mail is Eugene L. Ashley, for it was through his efforts that the development of the greatest power on the Hudson river was made possible. For several years prior to 1897 the various properties along the river between Glens Falls and Palmer Falls were in the hands of speculators. These men knew the value of waterrights, but they had not the ability to assemble the properties and finance such an undertaking. In 1897 Mr. Ashley began buying these water-rights, and, after two years of litigation, title mas secured to all of the properties along each side of the river, and the Hudson River Water-Power Company was organized to construct a dam and transmit power to the surrounding cities and villages. A contract was let for a dam

Jan 1, 1904

By J. E. Neal, C. T. Naber, O&apos

Silicon thin films were deposited by electron beam evaporation in an ultrahigh vacuum onto (0001) and (1102) sapphire substrates. Attempts were made to correlate the structural properties of the deposited silicon films with the following: 1) substrate orientation, 2) substrate surface condition, 3) substrate temperature, and 4) deposition rate. The substrate temperatures were varied between 500° and 1000°C and the deposition rates were varied between approximately 50 and 700A per min. The following sapphire surface treatments were investigated: 1) annealing in the ultrahigh vacuum at 1200° C; 2) heating in a hydrogen atmosphere at about 1350°C; and 3) etching with silicon by evaporating silicon onto sapphire substrates heated to 1200° or 1300°C. Twinned silicon films were occasionally formed at substrate temperatures between the 800° and 1000°C on unprocessed mechanically polished substrates; however, the reproducibility and crystallinity of these films were generally poor. Single-crystal and twinned silicon films were formed at substrate temperatures between 700° and 1000°C on substrates which were silicon-etched at 1300°C prior to deposition. Fiber texture films were formed at substrate temperatures between 500° and 700°C. The (111) lattice plane of the silicon single-crystal films was parallel to the (0001) sapphire plane and the (100) silicon plane was parallel to the (1102) sapphire plane. TECHNIQUES are well-established for growing single-crystal silicon thin films on sapphire by chemical methods.'-* Vacuum epitaxial techniques have a number of advantages over chemical epitaxial techniques in the fabrication of thin film microcircuits.5 One of the most significant is that vacuum techniques are compatible with well-established procedures for forming vacuum-deposited thin-film resistors, capacitors, and interconnections. Salatna, Tucker, and young6 recently reported the formation of relatively poor crystalline-quality silicon films on sapphire by electron beam evaporation in a vacuum of about 7 x 10-7 Torr. The purpose of the investigation described here is to determine the relationships between the structural properties of silicon thin films deposited on sapphire substrates by electron beam evaporation in an ultra-high vacuum and the following: 1) substrate orientation; 2) substrate surface condition; 3) substrate temperature; and 4) deposition rate. The substrate temperatures were varied between 500° and 1000° C and the deposition rates were varied between approximately 50 and 700A per min. Two orientations of sapphire were used: (0001) and (1102). The thick-nesses of the films were between 8000 and 16,000A. The morphology and crystallinity of the deposited films and substrate surfaces were investigated by optical microscopy, electron microscopy, and electron diffraction. APPARATUS AND PROCEDURE A cross section of the ultrahigh-vacuum thin-film evaporator is shown in Fig. 1. The bell jar is stainless steel and copper gaskets are utilized at all seals. High vacuum is attained by a 6001iter per sec ion pump and a titanium sublimation pump. Sorption pumps are used to rough the system to a pressure of about 10 µ prior to starting the ion pump. Vacuums in the 10- 10 Torr range were attained after baking the system at about 250°C for 8 hr. Vacuums in the 10-8 to 10-9 Torr range were maintained during silicon evaporation. The silicon charges, which were cut from p-type single-crystal boules which had resistivities between 2000 and 4500 ohm-cm, were placed in the water-cooled copper crucible of a 180 deg bent-beam 5-kw electron beam evaporator. During evaporation, a molten zone was formed in the top center of the silicon charge, and the portion of the silicon charge in contact with the water-cooled crucible remained solid. The substrate heater, which has been described

Jan 1, 1969

By Wm Price

THE object of this paper is to present a survey of some of the physical properties of sheet nickel silver when subjected to cold rolling and when annealed at temperatures extending from 350° C. throughout the commercial annealing range. A number of alloys were taken from stock and analyzed. Four of these, representing low nickel and high nickel both with and without lead, were chosen for the tests. The analyses were as follows: ALLOY COPPER, LEAD, IRON, NICKEL, MANGANESE, ZINC, PER CENT. PER CENT. PER CENT. PER CENT. PER CENT. PER CENT A 64.68 Trace 0.194 - 6.73 0.06 remainder B 65.82 1.27 0.227 6.17 0.06 remainder C 65.44 Trace 0.345 17.83 0.08 remainder D 65.60 1.08 0.238 17.77 0.06 remainder These alloys were rolled in accordance with regular mill practice to approximately No. 6 B. & S. gage. The bars (which were then coiled) were annealed together in a mill muffle and afterwards pickled in a 10 per cent. sulfuric-acid solution and cold rolled in stages of approximately .one number (B. & S.) at a time to No. 18 B. & S. gage. After each stage, suitable samples were set aside for physical tests. Additional samples were chosen for tests after the bars were rolled to Nos. 8, 10, 12, and 14 gage. These samples were annealed together in the mill muffle and, after pickling, were finished on 0.050-in. gage, yielding a series of specimens 2, 4, 6, and 8 numbers hard for the subsequent annealing tests. Tensile test pieces 9 by 1 in. (22.9 by 2.5 cm.) were cut from both lots and the central portion was milled to give a test section 2 ½ in. long by ;Z in. wide. A distance of 2 in. was marked off on the edge of each specimen with light punch marks. In the case of the annealed alloys, Erichsen test pieces 4 by 2 1/2 in. were also taken.

Jan 10, 1920

APPROXIMATELY 3500 people thronged the Hotel Statler from February 18 to 24 for the 173rd general meeting of AIME. It was a technical extravaganza in that 82 technical sessions were held, at which 500 authors presented some 350 papers. Fortunately, Jerry Peirce, outgoing President, didn't have, to preside at all the events although after his year's stint as President, he has more than a nodding acquaintance with some of the latest problems in the mining, metals, and petroleum industries. Although the Welcoming Luncheon on Monday noon was the official opening of the meeting, Local Section Delegates and the Board of Directors convened on Saturday and Sunday, respectively. The large attendance and business like demeanor of these two groups was in accord with the energetic and competent service they have rendered the Institute through the year. To the applause of engineers and their wives who thronged the grand ballroom of the Statler for the Welcoming Luncheon, President Peirce introduced Oliver B. Hopkins, president of the Canadian Institute of Mining and Metallurgy and C. Gerow, secretary of CIM. Dr. Hopkins brought greetings from the CIM and expressed his satisfaction in the splendid spirit of cooperation that exists between the two Institutes. Dr. Hopkins is president, Interprovincial Pipe Line Co., Toronto, and counts as a close personal friend M. L. Haider, who is the 1952 President of AIME and lately of Toronto where he was a director and general manager of Imperial Oil Ltd. Mr. Haider will be known shortly as Mike to thousands of AIME members as he makes his Local Sections presidential tour. There was a pause in luncheon proceedings when Judge Harold R. Medina arrived amid the applause of the audience and somewhat breathless from his trip via motorcade from an antitrust trial against investment bankers at the courthouse downtown. With the Judge at his elbow, President Peirce took the opportunity in his introduction to good humoredly chide the Judge for the vixenish habits of public servants in their treatment of astute businessmen. The successful inventor who patents his inventions is a monopoly; the copper manufacturer who buys his competitors a drink is in collusion; but the business failure need only look to the government for a subsidy, Mr. Peirce pointed out. Judge Medina, quickly captured the admiration of his listeners. He spoke about justice, deploring partisan deals on nominations for judge-

Jan 1, 1952

By R. G. Davies, R. H. Richman

Several techniques, X-ray diffraction, transmission electron microscopy, conventional, metallography, and mechanical property measurements are combined to investigate decomposition in the suPersaturated solid solution Fe-27 at. pct Be. The following sequence of structures for aging temperatures below 400°C is established: massive short-range order, pseudo-FeBe (L2o) order, Fe3Be (DU3) order, sinusoidal modulation of composition, general or continuous precipitation, and discontinuous or cellular precipitation. In addition to this sequence itself, several features of the individual stages are noteworthy; for example, when coherent modulations occur, their development is parallel to (100) everywhere in the specimen apparently without incubation, and both the wavelength and the composition amplitude of the modulations increase with aging time. Two types of discontinuous reaction are observed, depending upon the aging temperature. At low temperatures (<550°C) the boundary-nucleated variety of discontinuous precipitate predominates; but at higher temperatures (>600°C) the crystallographic variety occurs instead. Hardness and flow-stress measurements clearly reflect the quoted structure sequence. Some qualitative aspects of the structure changes and of the relationship between mechanical properties and structure are discussed. BERYLLIUM in solid solution markedly strengthens iron.&apos;" A recent study demonstrated that not only were supersaturated single crystals of Fe-27 at. pct Be very strong, but they deformed primarily by mechanical twinning.3 Such behavior, coupled with the decrease in solid solubility of beryllium in a Fe from about 33 at. pct at 1165°C to about 10 at. pct at 500°C4 as shown in Fig. 1, leads naturally to questions about property changes with aging in this system. In 1929 roll,1 and later Seljesater and Rogers,5 reported that useful increases in strength could be obtained by aging quenched Fe-Be alloys, but it was not until quite recently that any of the details of precipitation in these alloys were studied. Richman6 observed that both an Fe3Be superlattice (with a DO3 crystal structure the same as Fe3A1, illustrated in Fig. 2) and a modulated structure preceded the appearance of a discrete second phase in the 20 at. pct Be composition. Here, a modulated structure refers to a periodic composition fluctuation within one crystal, while its lattice remains coherent. Subsequent work on a Fe-Be alloys by Heubner7 and von Heimendahl and Heubner8 confirmed the existence of the modulated structure, although only an FeBe (L20) ordered structure was detected (also shown in Fig. 2). Both Rich-man and Heubner corroborated the large increases in hardness during aging reported earlier, but other mechanical properties were not examined. Since modulated systems are encountered relatively infrequently, the influence of coherent modulation upon mechanical properties is not well-known. With the accumulation of information about age-hardening systems, it has become clear that many precipitation reactions cannot always be described by the concept of heterogeneous nucleation at some lattice discontinuity followed by diffusional growth. Rather, complex sequences involving prior "preparation" of the matrix are quite common; that is, a transition structure occurs in the parent phase, instead of in some "nucleus" form. Delineation of such subtle sequences appears to be a worthwhile step toward the understanding of solid-state precipitation. Since not many structural progressions of comparable nature have been reported, the objectives of the present survey are to identify and elucidate the various

Jan 1, 1967

By M. E. V. Plummer, F. E. Beamish, J. C. Hole, J. M. Kavanagh

Prior researches have shown that the iron-copper-nickel content of platinum concentrates may be reduced by carbon to form a collecting alloy for the platinum metals in a manner exactly analogous to the formation of the lead fire assay button. The nature of the iron-copper-nickel alloys with the platinum metals has been investigated. Palladium and probably some of the other platinum metals form solid solutions with this alloy. ONE of the greatest known reserves of the platinum metals is to be found in the nickel, copper, iron sulphide deposits of Northern Ontario. The very large tonnage of copper-nickel ore processed makes the Sudbury district a significant world source of the platinum metals, the latter being recovered as byproducts in the electrolytic refining process for copper and nickel. Chalcopyrite, pentlandite, and pyrrhotite are carriers of the platinum metals;&apos; these minerals contain from 0.03 to 2.0 ppm of the noble metals. The analysis of the above ores for the platinum metals necessitates an initial concentration of the minute quantities present in the ore. The method usually employed involves the extraction of the noble metals by molten lead with or without small proportions of silver. The lead is then separated from the precious metals by cupellation, a process which involves absorption by the cupel and volatilization of lead oxide, leaving the precious metals collected in a silver bead on the surface of the cupel. The collection by lead is probably achieved by a process of dissolution followed by some degree of segregation in the lead alloy since the cold button is seldom uniform in composition. With silver-lead alloys this process of liquation has been used to re- cover pure lead since, during the cooling period, crystals of pure lead separate and silver becomes concentrated toward the center of the solid.&apos; Platinum and gold liquate in a manner similar to silver which may account for the successful recovery of platinum by fire assay even though it is considered insoluble in a solid lead medium. 3 In the case of iridium the liquation process may be a disadvantage in that the iridium may appear in the outer areas of the button and thus be lost mechanically during the handling processes. In any case the deficient alloying characteristics of lead for the platinum metals encouraged attempts to find an improved collecting alloy, and by analogy with aqueous extractions, preferably one in which solid solutions would be readily formed. Since, beyond a certain minimum solute to solvent ratio, the formation of a solid solution is accompanied by a lattice distortion, one would expect some relationship between the atomic diameters of any two metals and their tendency to form a solid solution. In one survey5 the hypothesis was put forward that when the atomic diameter of the solute differs by more than about 15 pct from the solvent, the "size factor" is unfavorable and the formation of a solid solution is restricted. On the other hand, when the atomic diameters are within this limit the size factor is favorable and solid solutions are readily formed, e.g. the transition metals of Group VIII having similar radii form solid solutions over wide ranges of composition.6 Even with a favorable size factor, elements having different crystal structures cannot form a continuous series of solid solutions. Cell dimensions alter as the concentration of the solute increases, causing a

Jan 1, 1962

By H. A. Coy

THE Mascot mines of the American Zinc. Co. of Tennessee are situated at Mascot, Tenn., 14 miles northeast of Knoxville, on the Southern Railway. The district is centrally located in the Great Valley, or Appalachian Valley Province. Prior to 1900, a small output of zinc was obtained from oxidized ore mined in open pits. In 1900, a shaft was sunk to sulfide ore, and in 1903, a second shaft was put down, neither being as deep as 200 ft. The American Zinc Co. of Tennessee began drilling in 1911, and outlined an ore body to which its No. 1 shaft was sunk, to a depth of 365 ft. Since that time, the American Zinc Co. of Tennessee has been the only operator in. the district. The Federal mining laws have never been in operation in Tennessee and mining lands are as irregular in boundary and area as farm lands. Ownerships are generally held in fee. In most cases the surface and mineral rights, are transferred together. Electric power is supplied at 66,000 volts by the Tennessee Power do, from a hydro-electric plant at Parksville, Polk County, Tenn., 100 miles from Mascot. No other power is used, but an emergency steam plant is held ready in case of interruption of service. Labor is all native and non-union. Negroes are employed for most of the shoveling, and for a few miscellaneous jobs, but for almost, no other work.

Jan 9, 1924

By R. B. Burt, J. A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By S. Shapiro, J. A. Ford

The crystallo graphy of several grains of the lamellar Ni-Ni3 B eutectic solidified under conditions appvoachirt equilibriun has been examined.. A preferred interlace relationship has been observed in this system which may be described as: A detailed study of this interface by means of an atomistic model reveals the interface Plane to be puckered and more accurately describable as: Analysis of the atomic configuration on these planes reveals that this interface conforms to the orientation criteria proposed for directionally solidified lanzellar eutectics. In addition, a model is proposed to help explain the growth of a "puckered" interface. DURING the past several years an increasing number of unidirectional solidification experiments on eutectic alloys have been reported in the literature. The primary emphasis, in most cases, has been the effect of growth variables on microstructure. Some authors have, however, studied the crystallographic orientations and interfacial relationships resulting from these experiments. Four crystallographic studies have been published;&apos;-4 in each of these there is a factor which tends to prohibit the extension of the observations beyond the particular system. In the Al-CuA12 system, the approximately equal volume fractions of the phases have resulted in sorrie controversy as to which phase constitutes the matrix. In the Mg-Mg,Sn eutectic the presence of several interconnecting lamellar systems2 complicates the analysis. The two remaining eutectics. 1nSb-b and Al-Ali, are both rodlike (the latter exhibits a plate morphology at low solidification rates): the matrix in each of these alloys is the simpler (fcc) phase. Studies of nucleation in eutectic alloys indicate that the more complex constituent is the nucleating -.phase.&apos; For the purpose of an analysis of interface crystallography it was deemed desirable to study a lamellar system in which the matrix was the more complex and, presumably. the nucleating phase. Recently it has been shown that there is a eutectic in the Ni-B system between Ni3B and i; preliminary investigation by the authors indicated that the matrix in this eutectic is the boride phase. The structure of Ni,B is reported to be orthorhombic, the compound being isostructural with cementite. This eutectic is therefore analogous to that between austenite and cementite. Furthermore, the Ni-B system is not susceptible to a competing eutectic reaction as occurs in the Fe-C alloys; nor does it exhibit a eutectoid decomposition. For these reasons the study of the interfacial relationship in the Ni-Ni3B eutectic was undertaken. PROCEDURE Ingots of nominal composition 3.5 and 3.6 wt pct B were induction-melted in boron nitride crucibles within a graphite susceptor under a boric oxide slag; a dynamic argon atmosphere was maintained over the melt to prevent rapid oxidation of the susceptor. The raw materials used were 99.97 pct Ni from Huntington Metals Division of International Nickel Co. and 99.8+ pct B chips supplied by the United Mineral and Chemical Co. The analyses of the starting materials are listed in Table I. The melt was held at 1500cC for 2 hr to insure complete reaction and allowed to cool to room temperature. The castings were chemically analyzed for boron and were metallographically examined for uniformity. The metallographic samples were mechanically polished through 0.1 p A1,0, and etched with Carapella&apos;s reagent. Each master casting was cut up to make several specimen blanks which were remelted, in boron nitride crucibles, to form ingots of 1/2 to 3/4 in. in diarn by 7 in. long. These ingots were unidirectionally solidified using a modified vertical Bridgman technique. The rate of solidification was assumed to be equal to the uniform rate at which the crucible-susceptor assembly was withdrawn from the induction coil. This rate was varied from 1.18 to 2.21 cm per hr. In order to perform these experiments it was found necessary to redetermine the eutectic composition. This was accomplished by the zone-melting technique described by Yue and lark.&apos; An ingot of 4.5 wt pct B was zone-melted in a horizontal boron nitride boat 7-1/2 in. long with a 112-in.-square cross section. A

Jan 1, 1967

By Samuel Daniels

The Al-Cu-Ni-Mg alloy is much benefited by heat treatment and, in such condition, is preferable to the Al-Cu-Fe-Mg alloy either as cast or as heat-treated, when both are reheated to temperatures of from 400" to 600" F. and compared, cold, with respect to strength and to hardness. The main differences between the alloys do not arise until the reheating temperature exceeds 400" F., above which they gradually soften. This softening is characterized metallographically by the appearance of intragranular precipitate. The Al-Cu-Ni-Mg alloy is weakest and least hard after being reheated at 600" F., the Al-Cu-Fe-Mg alloy at about 700" F. The former starts to reharden at 700" F., the latter at 800&apos; F. There is a tendency for both alloys to lose strength and hardness with prolongation of time at the reheating temperatures of 500" and of 700" F. The Al-Cu-Ni-Mg alloy is considerably stronger and harder than the Al-Cu-Fe-Mg alloy when both are heat-treated and reheated for long periods of time at 500" and 700" F. Although the latter can be made harder initially than the Al-Cu-Ni-Mg alloy by suitable quenching and aging, heat treatment, in general, favors the retention of this initial (strength and) hardness after reheating to a much greater degree in the Al-Cu-Ni-Mg alloy. The percentage of elongation of the two materials in any condition is very small. Certain aluminum alloys have been used for pistons and other parts operating at temperatures up to 650" F. because of their lightness, high thermal conductivity and specific heat, fair strength and hardness at elevated temperatures, excellent machineability, and moderate resistance to corrosion. In the piston, the inertia forces and the bearing loading, and with this the vibration, are decreased. The piston head functions at a lower temperature (about 200" F. below one of cast iron), so that, because of the lessened tendency toward carbonization and detonation, higher compression ratios may be used. On the other hand, the aluminum alloys do not have the wearing and bearing qualities of cast iron; also they have a large coefficient of expansion, allowance for which must be made in the design. The range in analyses of aluminum alloys, used for pistons in domestic and in foreign internal-combustion engines is shown in Table 1. There seem to be three general types of composition; one containing about 10

Jan 1, 1926

By Martin A. Moyers

THE nation&apos;s effort to win the war speedily is reflected in current trends in coal utilization, as in all other fields of our lives. In all industries, wherever coal is used for the production of heat and power the emphasis is on getting the most useful result with the least expenditure of matt.ria1. In addition to carrying its own share of the load, increased as it is by the demands of war industry, coal has had to fill in for the other fuels, mainly petroleum products, whose distribution from their more distant sources has been crippled by lack of shipping. Thus, the outstanding note in the utilization of coal this year is not the development of new methods of burning or handling coal but the extraordinary job that the industry has done in producing enough coal to serve all needs.

Jan 1, 1943

By F. D. George, M. J. Salkind

Al3Ni whisker-reinforced aluminum was found to exhibit good Charpy impact toughness and little notch sensitivity even though its room-temperature tensile elongation parallel to the whiskers is only 2 pct. This impact behavior was maintained d liquid nitrogen temperature (-196"C). It is postulated that this behavior is due primarily to the presence of the continuous aluminum matrix which provides sufficient 10calized ductility in the vicinity of the crack tip to absorb considerable energy from the advancing crack. The impact behavior of Al-Alni was found to be quite anisotropic. Of six orientations studied, the transverse orientation having the notch normal to the whisker axis was found to exhibit the lowest impact energy, whereas the transverse orientation having the notch parallel to the whisker axis was found to exhibit the highest impact energy. A significant differnce was noted between the impact behavior of material containing needlelike whiskers and that containing bladelike whiskers. Only two of the six orientations studied exhibited complete fracture for the material containing needlelike whiskers. On the other had, most of the specimens containing bladelike whiskers exhibited complete fracture. It was postulated that the bladelike whiskers block transverse flow, thus reducing the amount of plastic deformation ahead of the crack tip. One of the more significant advantages of composite materials is the prospect of combining high strength with toughness. In general, toughness is associated with materials which exhibit considerable ductility and can deform plastically in the presence of a stress concentration. Very strong materials which resist plastic deformation generally exhibit low toughness. At first glance, then, it would appear as though strength and toughness are mutually incompatible so that useful engineering materials would have to be a compromise between the two. One approach to the problem of combining the high intrinsic strength of ceramics with the toughness of metals was to mix them together to form a cermet. Unfortunately, the toughness of cermets was found to be rather disappointing. Whisker reinforcement of metals, however, appears to be a more promising approach. It has been demonstrated that whisker-reinforced metals produced by unidirectional solidification exhibit enhanced strength due to the presence of high strength nonmetallic whiskers. The total strain capacity of these composites in the direction of fiber alignment is limited to that of the fibers, the matrix being unable to carry the load once the fibers have failed. A characteristic, then, of whisker composites is low ductility in the direction of whisker alignment, on the order of a few percent elongation. This low elongation, which is usually associated with brittle behavior, should not be taken as an indication of low toughness. Such a material can exhibit significant ductility in directions other than parallel to the fibers7 and can therefore possess significant intrinsic toughness. Toughness in a fiber-reinforced metal is derived from several mechanisms. The first is due to the toughness of the matrix itself. A continuous ductile metal matrix can act as an effective crack arrest medium by undergoing localized plastic deformation. Cracks initiated from the surface of the composite or from a brittle fiber failure must travel through the matrix before reaching another brittle phase particle. A second crack arrest mechanism peculiar to fiber composites is due to the fact that, as a crack travels through the matrix and approaches a fiber, the plastic deformation ahead of the crack tip will result in loading of the fiber. This causes the matrix shear strength in the plastic zone to be apparently higher, thus extracting more energy from the crack and diverting the crack at an angle to the original direction of propagation. A third crack arrest mechanism occurs in fiber composites which exhibit a weak bond between fiber and matrix. The idea was proposed by Cook and Gordons that if a crack propagating transversely in a fiber composite were made to turn and run along the fibers by decohesion of the fiber-matrix bond, then toughness would be imparted by the blunting of the crack tip and the creation of new surfaces. The last mechanism, interfacial decohesion, is commonly noted in naturally occurring fiber composites such as wood, bone, and bamboo, and has been observed in man-made composites such as glass fiber-reinforced resins,g silica fiber-reinforced aluminum," laminated steel," and tungsten and silica fiber-reinforced electroplated copper.&apos;&apos; The first mechanism, crack arrest by plastic deformation in the matrix, has been noted in tungsten wire reinforced cast copper." The purpose of this investigation was to quantitatively assess the toughness of a whisker-reinforced metal as a function of orientation. Previous investigation considered only cracks propagating nominally perpendicular to the reinforcement. In this investigation, crack propagation in three mutually perpendicular directions as well as three intermediate orientations was investigated. The system chosen for study was the unidirectionally solidified A1-A13Ni eu-tectic alloy which has a microstructure consisting of 10 pct by volume of A13Ni whiskers in a matrix of aluminum This material exhibits two different kinds of whisker morphology, depending upon the rate at which it is solidified.&apos; At low rates of solidification (less than 2 cm per hr) the whiskers are bladelike, whereas at higher rates of solidification they are

Jan 1, 1969

By D. A. Munro, G. P. Contractor

Fourteen 50-lb laboratory melts were investigated to determine the effect of uranium on the tenpering characteristics of loo-carbon (0.06 to 0.1 pct C) steels. It was found that uranium additions, particularly in the range 0.30 to 0.45 pct, enhanced the hardness and both ultimate and yield strength of the experivzental steels in the quenched and tempered condition. The structural and morphological chazges indicated that uranium retarded tempering of the tnartensite, thereby hindering the normal formation of polygonal ferrite formed in the late stages of tempering. The effect of this was to make possible the re-tension of the acicilar ferritic structure in the uranium-bearing&apos; steels. The iraniuin-bearing steels also showed IVidnzanstatten-type growth of ferrite plates and had large prior austenite grains containing assenzblies of fine ferrite grains, mainly acicular in geometry. The fine-grained ferrite structure and the presence of more numerous and apparently smaller precipitates in the uranium-bearing steels are thought to he principally responsible for the itnproved tensile strength and hardness of the experinzental uranium-bearing steels. At ternperirzg temperatures above 455% (850&apos;F) the ferrite in the higher-uraniun steels nzaintained acicularity and, hence, its strength and resistance to tempering. Uranium did not produce a secondary hardening peak. However, it retarded softening during the third stage of tempering because of its effect of inhibiting the grouth of cementite particles and of retaining the acicularity of ferrite plates. The resistance to coalescence accounted for the slow grocth of the ferrite grains in the uranium-modified steels and, hence, fov the persistence of the acicular ferrite structure. IT had been found previously1 that uranium additions up to about 0.45 pct had no significant effect on the tensile properties of low-carbon steel (0.06 to 0.10 pct C) in the as-rolled and normalized conditions, Fig. 1. On the other hand, it was observed that uranium in excess of about 0.30 pct had an embrittling effect as revealed by Charpy V-notch impact results. It was also noted that, as the uranium content increased, the morphology of pearlite changed from lamellar to feathery and the ferrite grains showed an etching effect resembling striated or dashed markings, suggestive of precipitation. The sharp drop in the impact properties shown in Fig. 2 warranted an assumption that the uranium content of about 0.30 to 0.45 pct may produce some secondary hardening reaction on tempering, analogous to that associated with a Cr-Mo-V steel, which shows very poor CVN toughness at the secondary hardness peak in the tempering curve.1&apos; With this background and the reported findings of Hasegawa and noda that low-carbon uranium-treated steel showed signs of secondary hardening, the present investigation was undertaken to determine the effect of uranium additions on the mechanical properties of 0.10 pct C steels. No attempts were made to investigate in detail the mechanisms of hardening, although some suggestions based on the experiments are made. MATERIALS AND PROCEDURES A series of 50-lb induction-furnace melts was made using AISI 1008 rimming steel billets as the melting stock. The melting, forging, and rolling techniques proven satisfactory in previous projects&apos;-3 were employed as a guide for this investigation. The steel was deoxidized with aluminum (2 lb per ton) prior to the addition of high-purity uranium. The analysis of each melt is given in Table I. Properties were evaluated as a function of heat treatment and are presented in terms of hardness and tensile strength vs tempering temperatures. The variation of hardness with the tempering temperature was studied on the quenched and tempered specimens, some of which measured 0.50 by 0.25 in. diam and the others 0.40-in. cubes. Before quenching, the specimens were vacuum-sealed in glass tubes and normalized at 900°C (1650°F) for 20 min. Following this treatment, the sealed specimens were hardened by austenitizing at 955°C (1750°F) for 20 min and water quenching, and then tempered for 1 hr in the range 150 to 730°C

Jan 1, 1967

By Pradeep K. Rohatgi, Clyde M. Adams

Structures obtained on freezing of several hypo-and hypereutectic Al-Cu alloys over a range of solidification rates have been examined. Dendrite spacing, L, increases linearly with solute concentration and with the square root of the inverse freezing rate. The relationship for hypoeutectic alloys is: where rate of change of fraction solid with time, is freezing rate, C is solute concentration, (pct Cu)=1. Mass transport in inter dendritic liquid during solidification is analyzed; the experimental observations suggest maximum concentration differences and constitutional supercooling in the inter dendritic liquid increase with an increase in the solute concentration. The dendrite morphology changes with freezing rate and alloy composition. The dendrites of the a phase are parallel, uniformly spaced plates with slow freezing and rods with rapid freezing. Nonor-thogonal side branching has been observed in phases with cubic and tetragonal structures. Side branches in a dendrites are orthogonal with slow freezing and at 60 deg with rapid freezing. Formation of second-phase envelopes around the Primary phase is also discussed. DENDRITIC structure is characteristic of many types of phase transformation. The most extensively studied so far has been solidification of liquid solutions. chalmersl and coworkers have interpreted the formation of dendrites in terms of the breakdown of a planar interface. Most of the work done concerns itself with the development of an instability at the interface. Little theoretical work has been done quantitatively to relate the parameters of dendritic structure to mass transport in the liquid phase. A few empirical relations based on the experimental2&apos;3 observations exist in the literature. Several workers2 including Brown and Adams1 have studied dendrite spacing in A1-Cu system as a function of solidification variables. In most cases, dendrite spacing has been found to increase linearly with the square root of some parameter proportional to the freezing time. The effect of solute concentration is not clear; some workers report the dendrite spacing increases with solute concentration4 whereas others report vice versa.&apos;&apos;&apos; ~ohatgi&apos; has observed an increase in the spacing between ice dendrites with an increase in solute concentration in water. Tiller has also suggested that dendrite spacing should increase with solute concentration. In the present work dendrite spacing and morphology have been examined as a function of solute concentration and freezing rate. The freezing rate is defined as the fraction of liquid solidified per unit time, dfs/dß?, where f, is the fraction solid and 8 the time. The fastest freezing rate studied was 4550 times the slowest freezing rate. THEORETICAL CONSIDERATIONS It is of interest to analyze the concentration distribution in the liquid phase between growing dendrites during solidification, Fig. 1. Since this distribution is a direct consequence of the rejection of solute by the growing solid, a diffusional process, the concentration gradients increase with the freezing rate. However, when solidification rate is the only variable in a series of experiments, the interdendritic liquid regions become smaller (i.e., the dendrites become more closely spaced) with an increase in freezing rate. The main purpose of the analytical treatment of interdendritic liquid diffusion will be to reveal a tendency for dendrite spacing to decrease with increasing solidification rate in just such a way that the maximum concentration differences developed in the liquid phase are remarkably independent of freezing rate. Two rather different analyses are set forth, one pertaining to the one-dimensional diffusion which obtains in the interdendritic liquid between parallel plate-shaped dendrites, and the other to the cylindrically symmetrical diffusion around rod-shaped dendrites during early stages of solidification. The results of the two analyses are quantitatively similar, correlating dendrite spacing, maximum concentration difference, and freezing rate. First consider the simpler one-dimensional case. Two parallel plate-shaped dendrites are separated by a distance, L, between centers, Fig. 1. Solidification takes place by the thickening of these plates, with solute being rejected into the liquid. It is assumed there is no diffusion in the solid. This thickening process is slow enough and the dendrite spacing small enough that the concentration differences which develop, although interesting and important, are very small (an important assumption which is verified ex-

Jan 1, 1968

By A. B. Kinzel

PRECISE knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the sane. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly well known. GENERAL METHOD The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By S. Jana, C. M. Wayman

The reverse transformation of bcc martensite to the fcc phase was studied in an Fe-33.95 wl pct Ni alloy by nzeans oj dilatometry, melallography, and electron microscopy. Upon "slozc" heating (-1°C per min) length cJmnge us temperature plots showed u gradual contracLion over the temperature range 200" to 280"C ,followed by a more abrupt contraction beginning a1 -280°C. Howet,ev, zchen the heating rate was increased -4°C per tnin, no gradual contraction was observed and only the abrupt contraction starting at -2BO"C was found. Thus on slower heating- the AS "temperature" for the subject alloy, unlike the MS temperature, is better defined as a range of temperatures. Both optical and transmissiorl electron microscope observations showed that some of the martensite plates exizibited a partial loss of transformation twins during reversal. The midvib region of the martensite plates disappeaved relatively early duirng the reversal. Metallographic observations slowed that the earliest detectable stage of the rezlerse tvansforrvration begins (axd Moues inulardly) at The Martensens i te - parent interface. At higher temperatirres, the. formation of martensitically reversed jcc plates within the bcc martensite plales was observed. It is concluded that the reverse transformation consists of a diffusion less process (martensitic); but this is ps-obably aided by a prior or simultaneous dijjusiorz-comltvolled process, at leasl in the case of slower heat-ing&apos; experiments. ALTHOUGH numerous investigations have dealt with the parent-to-martensite ("forward") transformation (fcc — bcc) in Fe-Ni alloys, comparatively little is reported on the ("reverse7&apos;) martensite-to-parent transformation.&apos;-4 Even though such reverse transformations have been studied in detail in some nonferrous systems, one of the difficulties of studying the reverse transformation in most ferrous mar-tensites is that the martensite decomposes by tempering during heating. However, carbonless Fe-Ni alloys do not exhibit this difficulty since the transformation in these alloys is completely reversible. The present investigation represents an attempt to shed more light on the nature and mechanism of the martensite-to-parent transformation. 1) EXPERIMENTAL PROCEDURE 1.1) Alloy Prepatation. Fe-Ni alloys of compositions near 34 wt pct Ni were prepared from zone-refined iron (99.994 wt pct Fe) and high-purity nickel (99.999 wt pct Ni) by induction melting in recrystallized alumina crucibles in an argon atmosphere, with prior vacuum evacuation to 10"3 mm Hg. The alloys were homogenized by induction stirring in the molten state for 5 min. After solidification, the alloys were further homogenized in evacuated quartz capsules for 96 hr at 1230°C. 1.2) Dilatometry. Slices of the ingot were hot-forged (750°C in air) into approximate rod form and these specimens were then hot-swaged (750°C in air) into long cylindrical rods 0.55 mm diam. From the rods, specimens about 1 in. long were cut. These were then vacuum-annealed for 24 hr at 1200°C, cooled to room temperature, and subsequently transformed to martensite in liquid nitrogen (whereby about 40 pct transformation was obtained). Dilatation measurements were made by observing length changes in a vacuum dilatometer with an externally mounted LVDT sensing element. 1. 3) Preparation of Electron Microscope Specimens. Slices of the ingots were cold-rolled (with intermediate vacuum anneals) to -0.020 in. Out of these rolled sheets, specimens (about 1 by 1 in.) were cut. These were then vacuum-annealed, transformed to martensite by cooling in liquid nitrogen, and subsequently heated from room temperature to various temperatures to effect either partial or complete reverse transformation. These specimens were then chemically polished to 0.002 in. in l:l HsOz (30 pct) and &PO4 (85 pct) solution, and thinned to electron transparency in an electrolyte consisting of 150 g CraOs, 750 ml glacial acetic acid, and 30 ml ~~0.~ Observations were made with a 100-kv Hitachi HU-11 electron microscope equipped with an HK-2A tilting device. 1.4) Optical Microscopy. Metallographic observations were made with a Leitz MM5 metallograph on the same 0.020-in. sheet specimens as were used for electron microscopy and on bulk specimens which were 0.2 in. or more on a side. The chemical thinning solution when cooled below 20°C also served as an etchant for this alloy. Observations of surface relief were made with a Zeiss interference microscope employing a Thallium light source of wavelength 0.54 p. Specimens for interference studies were prepared by two-stage polishing on Buehler vibromet polishers using 0.3 and 0.05 p alumina abrasives. 2) EXPERIMENTAL RESULTS 2.1) Comparison of the MS,AS, and Af Tempera-tures wTth Previous Re sults. The AS aLd Af tempera -tures of several Fe-Ni alloys were determined dila-tometrically. The MS temperatures of the same alloys were determined by continuously lowering the temperature using a mixture of isopentane and liquid nitrogen and observing the highest temperature at which a prepolished specimen showed surface upheavals. For the present the As temperature is defined as the temperature at which an abrupt decrease in length occurs in the dilatation plot. The Ms,As7 and A determinations in the present investigation and those of Kaufman

Jan 1, 1968

By J. L. Lamon, W. Crafts

Study with the electron microscope of the carbides in vanadium-chromium-molybdenum steels after tempering up to 1000 hr at 600 teelsto 1400°F confirmed that alloy carbides are formed at the secondary hardening temperature by decomposition of the plate-like iron carbides. It was also demonstrated that vanadium carbide persists as much smaller particles than do chromium- or molybdenum-bearing carbides. Conditions conducive to the formation of fine vanadium carbides are indicated to be favorable for high temperature strength. IN order to determine the effects of long exposure at high temperatures on vanadium-bearing steels, a survey has been made of their hardness and carbide structure. The behavior of carbides in the tempering of martensite was studied by X ray diffraction and electron microscope examination of electrolytically extracted residues in greater detail than in an earlier investigation.&apos; A group of steels with about 0.25 pct carbon and containing chromium up to 5 pct, molybdenum up to 1 pct, and vanadium up to 1 pct was either quenched or annealed and then tempered for peri- ods of up to 1000 hr at 600° to 1400°F. Their hardness after tempering agreed with the Hollomon and Jaffe2 relation of equivalency of time and temperature, and with the degree of secondary hardening predicted from composition. Further, the appearance of the carbides indicated that the time and temperature equivalency relation was also applicable to the degree of carbide development. The mechanism of the tempering of martensite was demonstrated more clearly than in the earlier study. It was confirmed that carbides develop from martensite as poorly defined plates of the Fe2C type carbide followed by thickening of the plates with a transition to Fe,C. Finally the plate structure deteriorates into a lacy mass from which alloy carbides emerge as chunky particles that grow slowly with further increase of tempering temperature. Vanadium carbide derived from tempered martensite was found in characteristically small particles that tended to grow very slowly. The addition of chromium or molybdenum to a steel with predominant vanadium carbide tended to introduce carbides of a chromium- or molybdenum-bearing type having a somewhat larger particle size. The Cr,C, type carbide particles were larger than those of the V,C, type and somewhat smaller than the carbides in steel containing both Cr,C and M,C. Similar observations were made of the carbides in the pear lite of annealed steels. It appeared that high temperature properties would be benefited by the retention of the fine carbide particles that result from a balance of composition and heat-treatment designed to produce a maximum amount of vanadium carbide. Procedure: The steels used in the investigation were made with a base of Armco iron in a high-frequency furnace at the Union Carbide and Carbon Research Labs., Inc. The steels were deoxidized

Jan 1, 1951

By R. F. Hehemann, R. H. Goodenow

Thermal arrest, hot-stage microscopy, and transtnission electron microscopy techniques have been employed to study the transformations in low-carbon iron and Fe-9 pct Ni alloys. In continuous cooling experiments, each alloy transforms at an essentially constant temperature for cooling rates below the critical rate required for martensite formation. However, high-tenzperature transformation in pure iron takes place by a different mechanism than that in the 9 pct Ni alloys. Pure iron exhibits an equi-a a structure with a low and random dislocation density while the 9 pct Ni alloy exhibits a cell or lathlike substructure analogous to that of low-carbon martensite. This same substructure characterizes upper bainite in higher-carbon inaterials. UNTIL relatively recently, diffusionless transformations have been considered to take place by the same mechanism and have been termed mar-tensitic transformations.l-3 The most characteristic feature2 of this mode of transformation is the shape change produced by a shear deformation and growth of the product phase frequently occurs at an extremely high velocity approaching that of an elastic wave.4&apos;5 A different mechanism of diffusionless transformation was recognized first in Cu-Ga and other copper-base alloys.6,7 From the absence of surface tilting in these alloys, it has been concluded that transformation is not accomplished by the cooperative shear displacements that occur in mar-tensitic reactions. Transformation presumably takes place by the rapid movement of an incoherent interface which is capable of propagating across parent grain boundaries. Although the transformation is diffusionless in the macroscopic sense, advancement of these interfaces is accomplished by an atom by atom rearrangement. Transformations of this type therefore require thermal activation and are generally operative only at high temperature. Although requiring short-range diffusion at the interface, propagation still occurs so rapidly that the reaction cannot be suppressed with normal cooling rates.7 The resulting microstructures exhibit large, irregular-shaped regions of the product phase, which are essentially free of crystallographic features. Consequently, these reactions have been termed massive transformations. Transformation by the massive mechanism has been reported to occur in ferrous systems involving pure iron and binary alloys of iron with nickel, chromium, and silicon by Gilbert and owen.&apos; The Fe-Ni system is of special interest in that the massive transformation was observed in alloys with less than 15 pct Ni while alloys having more than about 28 pct Ni transformed by the conventional mar-tensitic mechanism. By employing cooling rates substantially higher than those used by Gilbert and Owen, Swanson and Parr have been able to suppress the massive transformation in alloys with 0 to 10 pct Ni9 and produce martensite as revealed by surface relief. The massive transformation in the alloys having less than 15 pct Ni was identified by the lack of surface relief and an irregular rather than clearly acicular microstructure.&apos; Speich and Swann, using thin-foil electron microscopy, identified three distinctly different structures10 in quenched binary Fe-Ni alloys. From 0 to 4 pct Ni the structure consisted of blocky grains of a with a low and random dislocation density. Alloys with 4 to 25 pct Ni exhibited a cell structure with a high dislocation density; and at greater than 25 pct Ni the structure consisted of internally twinned plates. The structural change at approximately 4 pct Ni suggests that alloys with low nickel content transform by a different mechanism than those with intermediate nickel contents and the transition from the cellular to the internally twinned structures at approximately 25 pct Ni is analogous to the transition from needles to internally twinned plates that occurs over a narrow range of carbon contents in Fe-C martensites.11,12 Conventional bainitic and martensitic modes of austenite decomposition operate in ternary Fe-C-Ni alloys having less than 10 pct Ni. This investigation was conducted in order to explore the conditions under which the massive, bainitic, and martensitic transformations occur and the relationships between these modes of decomposition.

Jan 1, 1965