Search Documents

By AIME AIME

AWIDE variety of subjects was discussed at the Wednesday sessions on Non-metallic Minerals. W. M. Weigel as chairman, presided at the morning session, and W. M. Myers, vice-chairman, in the afternoon. In the morning session a paper by W. N. Logan on "Mineral Wool Resources of Indiana" was read by H. H. Hughes. Mr. Logan explained that as Indiana is the principal source of mineral wool, the paper might well he entitled "Mineral Wool Resources of the United States."

Jan 1, 1932

By A. W. Gauger

WITHOUT QUESTION the Commonwealth of Pennsylvania contains the most remarkable coal deposits of the whole world. Within its borders ,are to be found excellent coals ranging in rank from the high volatile bituminous of the western part of 'the state through the low volatile or semi-bituminous of central Pennsylvania to that aristocrat of solid fuels, anthracite, found in the East. . . . But while other states and even the Federa1 Government have recognized the needs of the coal industry, Pennsylvania has not. Though bituminous coal represents one of the most important industries in the state, far more important in annual productive wealth than agriculture, for example, hundreds, of thousands of dollars have been spent on agricultural research whereas little or nothing has been spent on coal investigation.

Jan 1, 1932

By A. H. Bell

DEEPEST hole in the earth, and deepest producing oil well in the world-such is well No. K.C.L. A-2, of the Continental. Oil Co., completed on April 12 in the San Joaquin valley about four miles west of Wasco, Calif. It penetrated the earth's crust to a depth of 15,004 ft.- almost three miles-a depth that exceeds by over 2200 ft. that of the previous record holder in western Texas. It is now producing oil from sands at a depth from 13,092 to 13,- 175 ft., which is about 1500 ft. deeper than the record formerly achieved in Louisiana. Continental's new well was bottomed in what is possibly Domengine-Avenal Eocene sand, and is producing from the Middle Miocene equivalent to the Rio Bravo sand.

Jan 1, 1938

By F. R. Cattoir, R. W. Kimball, C. T. Anderson

ONE of the principal impurities in all steels is sulphur. Sulphur-bearing, manganese-free steels exhibit hot shortness. Manganese is added to steel to improve the hot-working properties. If no sulphur were present in steel, it is probable that hot shortness would be nonexistent. This paper is the first of a series to be issued by this Laboratory reporting the measurements of hot forgeability tests and the physical properties of Fe-C alloys to which additions of various alloying elements have been made. The present paper describes the results- obtained by the addition of varying amounts of sulphur to Fe-C alloys. To obtain control over residual elements in the various charges melted in the arc furnace, it was considered advantageous to use sponge iron from one source as the melting stock rather than scrap metal having an unknown history. Small amounts of unwanted alloying elements might be introduced into the charge when scrap was used, thereby influencing the results of the various heats. A sponge iron having a high silica-lime ratio was used. Ore from Sunrise, Wyo., had been reduced to sponge iron and briquetted at the Bureau of Mines sponge-iron plant at Laramie, Wyo. The briquettes were 5 in. in diam and 2 to 3 in. in thickness, and weighed about 10 lb each. The chemical analysis of the sponge iron is as follows: C, 0.67 pct; Mn, 0.10; SiO2, 4.75; CaO, 1.4; P, 0.044; S, 0.72; MgO, 0.4; A12O3, 1.1; total Fe, 87.5; Fe metallic, 79.2; and reduction, 90.5 pct. Where a reducing agent was required, crushed graphite electrodes usually were used. The charcoal available contained 0.20 pct S. An analysis of the available coke showed it to contain 0.70 pct S. Where high sulphur heats were required, elemental sulphur additions were made to the ladle. Limestone of good quality was obtained locally and had the following analysis: CaO, 53.7 pct; MgO, 0.8; ignition loss, 42.4; R2O3, 0.2; SiO2, 3.0; and P2O5, 0.014. Melting Procedure Sponge iron was melted to produce metal stock for the experimental alloys in a silica-lined, three-phase, direct-arc, size ST, Moore Rapid Lectromelt furnace with a 500 kva rating. Fig. 1 shows this furnace installation. About 25 tons of sponge iron was melted in 75 heats, averaging 927 lb of sponge iron to the heat. An addition of carbon was required to complete the reduction of a portion of the iron oxide remaining in the sponge to prevent high losses of iron oxide in the slag and a low carbon content in the resulting metal. As reducing agents in preparing the melting stock, charcoal, coke, and a carbon product resulting from the thermal decomposition of natural gas were used. The quantity varied from 20 to 60 Ib per furnace charge, with an average of 38 lb. An average analysis of the metal obtained gave 0.52 pct C, about 0.01 pct Mn, 0.070 pct P, and 0.092 pct S. The average yield of metal was 647 lb with 241 1b of slag, the sponge-iron recovery being 70 pct. The metal obtained in melting the sponge iron was cast into pigs weighing about 20 lb each to facilitate recharging into the furnace for further refining. The pouring of the pigs is shown in Fig. 2. The average power consumption for the production of the 24 tons of metal obtained was 1704 kw-hr per ton.

Jan 1, 1954

By H. E. Wilborg, G. V. Henderson

This chapter deals with those sands employed by foundries for the manufacture of cores and molds used in the casting of such common metals as steel, gray iron, ductile iron, aluminum-based alloys, and copper-based alloys. Most metal is cast in "green sand" molds in which the sand mixture, consisting primarily of silica, clay, and water, forms a plastic material. This plastic material is rammed around a pattern in a split box called a flask, then the box is separated, the pattern is withdrawn, and the metal is poured. These green sand molds are broken apart when the metal has solidified. The sand is then remixed and a new mold made for the next casting. To a lesser extent silica sand is mixed with resins or oils and, after forming, the mixture is hardened by either heat or chemical reaction. In any case, the foundry mold or core is used just once before being broken up and remixed for manufacturing another core or mold. By far the greatest consumption in the foundry is of those types of sand high in silica, low in clay (under 0.5%), and occurring in numerous locations thoughout the United States. Consumption End Uses Foundry sands fall into four distinct categories: silica sand, lake sand, bank sand, and natural molding sand. Silica sand is a general term used to describe washed, graded, dried, and cooled clay-free sands which are found in many parts of the United States. They generally contain 90 to 100% silica but vary greatly in chemical analysis and grain structure. Lake sand is the sand dredged from Lake Michigan or dug from the dunes bordering that lake. Bank sand is composed primarily of silica grain but containing up to 5% clay. It is shipped in both the damp and dry state but the normal processing of bank sand consists only of drying and scalping. Occasionally two different grades of bank sand are blended prior to or during loading. Natural molding sand is a term used to describe a sand containing sufficient clay as mined to be suitable for molding purposes. Clay content may vary from 10 to 24% with the balance of the material consisting primarily of silica sand. These sands range in fineness from one peaked on the 20 mesh to one which contains more than 50% of the particles passing the 270 mesh. Lake sands are relatively coarse and are used in great quantities for the production of automotive castings. Bank sands and natural molding sands are gradually phasing out as the production of castings becomes more a science and less an art. The vast majority of foundry sands used today are those known as the silica sands and lake sands. Foundry sands are used in two basic ways. The majority are used in the green or uncured state with the balance used in the cured or set state. Green sand is grain bonded with clay and contains varying amounts of water to plasticize the clay in order to bond the grains together. Green sand is either naturally bonded or "synthetic" sand. The naturally bonded molding sands are generally found in the Hudson River Valley of New York State, Cumberland County in New Jersey, and in Tennessee and Mississippi. Synthetic sand is molding sand compounded in the individual foundry. It is made up primarily of graded silica sand, western or southern bentonite, water, and carbonaceous and/or cellulosic materials. Green sand is used primarily in making molds. The use of naturally bonded green sand has been declining for many years, primarily because naturally bonded sands are more difficult for the foundryman to find and control. Synthetic green sand, on the other hand, can be

Jan 1, 1983

By A. E. Deruyttere, J. Van der Planken, M. Laurent, Van den Bergen

FahRENHORST and schmid1 observed that zinc single crystals work hardened less rapidly when strained in liquid air (- 185°C)than in a bath at -82°C, whereas at higher temperatures the rate of work hardening decreased with increasing temperature, as would be expected. Cadmium and magnesium showed no such decrease at -185°C. At that time the observed anomaly for zinc at liquid air temperature probably seemed insignificant. However it later was confirmed2 by experiments in liquid nitrogen (-196°C) and in the mixture solid carbon dioxide-acetone (-77"C) and therefore appeared to be real. seeger3 then suggested that the anomaly might be due to the different wetting of the zinc crystals by the cooling media. Recently a new confirmation was obtained,4 however the cooling media again were different: the rate of strain hardening was found to be lower in liquid nitrogen and liquid oxygen than in pentane cooled to various temperatures down to -126°C. Ekperiments will now be reported in which the medium surrounding the specimen at the different temperatures was the same, namely gaseous air. The single crystals were made from "Overcor 99.99" zinc. They were grown in a vertical traveling furnace on seeds of nearly the same orientations. The diameter of the crystals was 5 mm and the length between shoulders 140 mm. The brass shoulders were stuck to the crystals by means of araldite. A thin steel wire was fixed to each shoulder and served to fasten the specimen to a Houns-field tensile testing machine. The crystals with the shoulders and part of the wires were surrounded by two concentric cylindrical containers. The coolant. either liquid air or ground solid carbon dioxide, was poured into the outer container only. During cooling the containers rested on a support which was removed when the straining was started. In order to check the temperature which the crystals would attain inside the inner container, a hollow bar of zinc in which a thermocouple was fitted was first mounted in the apparatus as a substitute for a crystal. It appeared that a constant temperature, respectively - 183° and -72°C, was attained inside the bar, if a soaking time of the order of 1 hr was allowed and if the outer container was constantly kept filled. Accordingly, this procedure was adopted for every tensile test. To take account of the large scatter, fourteen tensile tests were performed with liquid air and seven with solid carbon dioxide. The orientation of the crystals and the results are presented in the table, in which the symbols have the following meaning: 1 : temperature x : initial angle between basal plane and specimen axis : initial angle between slip direction and specimen axis a : shear strain at fracture 0: average rate of strain hardening = —-——- 100 t0 and Te representing respectively the critical shear stress and the shear stress at fracture. Despite the scatter of the a- and 8— values which is of the same order of magnitude as in the work reported by Seeger and Trzuble,4 it is evident that the strain hardening rate is significantly lower at -183°C thanat-72°C. The table also contains the average values calculated from Seeger and Trauble's results at the corresponding temperatures: z.e., four results at -183oC and two at-70°, -71°C. These authors calculated 9 in a slightly different way, but this is unimportant. The agreement between the a-values shows that both sets of experiments are comparable despite the differences in experimental techniques. The rates of strain hardening also agree and it may therefore be concluded that the anomaly is not

Jan 1, 1962

By Edward Keller

(Canal Zone Meeting, November, 1910.) UNDER the title, Labor-Saving Appliances in the Works-Laboratory, I published a paper1 in which was described how multi-manipulations, in a works-laboratory, and in the furnace-room of an assay-laboratory, can be condensed into single manipulations by applying the proper mechanical devices. For example, I now deposit in, or withdraw from, a muffle a set of 48 cupels as one unit. The front row. (8) of these. are blanks or heaters; the other 40, when they have attained the proper temperature in the muffle, are charged simultaneously with the 40 lead-buttons. Three manipulations here accomplish an operation which by the generally customary method requires 136, and this number is only limited by the size of muffle and cupels. This operation is an enlargement of what I have already described in my former paper, and Fig. I shows the improved implements. In the paper referred to I described a gold-silver bead parting-bath, which is the last of the devices used in regular sequence in practice. This bath was designated as being convenient, but was not a labor-saver properly. Fig. 2 of the present paper shows a new device. Instead of the original tray, there are now sectional holders for the test-tubes, each having a wooden handle on either end, so that the holders may be removed from the boiling bath, and the acid or water poured off from each set of tubes (in this case, 7) without waiting to cool. The tubes, held in place by clutches, as shown in Fig. 3, rest in holes in the base-strip, having a smaller diameter than the tubes. Each holder is stamped at either end with a number, so that the bath becomes further useful by permitting several men to use it at the same time without interference. Apart from the handles, the holders are made of sheet-copper. ' Trans., xxxvi., 3 to 18 (1906).

Aug 1, 1910

By H. E. Hostetter

Grossmann's method1 for calculating the hardenability of steel from the composition and grain size has gained wide acceptance, and when properly used, has been well proved in practical application, both for estimating the hardenability of known compositions and for selecting compositions to meet known hardenability requirements. The Grossmann method uses as the criterion of hardenadility the "ideal critical diameter," DI, which is the' size round that will just harden to a structure of 50 per cent martensite at the center when given the theoretically fastest quench, or "ideal quench." The DI can be related to actual quenching practice if the severity of quench is known; or the DI can be correlated with hardenability as determined by the Jominy end-quench method.2 The effect on hardenability of each element present in a steel can be represented by a multiplying factor, the value of which depends on the amount of the element present and the degree of effectiveness of the particular element. (The value of the factor for a given carbon content varies with the grain size.) When the factors for all elements present in a steel have been determined from charts, they are multiplied, and the resultant product is the DI of the steel. The validity of Grossmann's scheme of multiplying factors has been confirmed in a number of other investigations.3-6 It can be appreciated that a certain desired level of hardenability can be obtained by adding chromium, molybdenum, nickel and vanadium to a base composition containing carbon, manganese, silicon and the usual impurities. Many of the ranges of hardenability used commercially can be obtained by any of the foregoing alloying elements used singly in the base composition. The same hardenability levels also can be obtained through use of any of a great number of multiple element combinations of these alloying elements. In this report a method will be presented for determining what one combination is the most efficient (based on hardenability and cost of added alloy) for a given level of hardenability. It should not be assumed from the emphasis given to hardenability, that hardenability is the only criterion for the selection of an alloy composition. Such properties as the hot-working characteristics, machinability, carburizing characteristics, amount of distortion during quenching and the retention of austenite may be considerations of importance in many applications. However, hardenability is one of the most important properties of an alloy steel and one that must be considered in almost all cases involving heat-treatment by quenching. Therefore, a method for determining the lowest-cost alloy combination should be of considerable value. Determination of Most Efficient Combinations For comparing the alloying elements on standards of cost and hardenability, it

Jan 1, 1947

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By H. E. Hostetter

Grossmann's method1 for calculating the hardenability of steel from the composition and grain size has gained wide acceptance, and when properly used, has been well proved in practical application, both for estimating the hardenability of known compositions and for selecting compositions to meet known hardenability requirements. The Grossmann method uses as the criterion of hardenadility the "ideal critical diameter," DI, which is the' size round that will just harden to a structure of 50 per cent martensite at the center when given the theoretically fastest quench, or "ideal quench." The DI can be related to actual quenching practice if the severity of quench is known; or the DI can be correlated with hardenability as determined by the Jominy end-quench method.2 The effect on hardenability of each element present in a steel can be represented by a multiplying factor, the value of which depends on the amount of the element present and the degree of effectiveness of the particular element. (The value of the factor for a given carbon content varies with the grain size.) When the factors for all elements present in a steel have been determined from charts, they are multiplied, and the resultant product is the DI of the steel. The validity of Grossmann's scheme of multiplying factors has been confirmed in a number of other investigations.3-6 It can be appreciated that a certain desired level of hardenability can be obtained by adding chromium, molybdenum, nickel and vanadium to a base composition containing carbon, manganese, silicon and the usual impurities. Many of the ranges of hardenability used commercially can be obtained by any of the foregoing alloying elements used singly in the base composition. The same hardenability levels also can be obtained through use of any of a great number of multiple element combinations of these alloying elements. In this report a method will be presented for determining what one combination is the most efficient (based on hardenability and cost of added alloy) for a given level of hardenability. It should not be assumed from the emphasis given to hardenability, that hardenability is the only criterion for the selection of an alloy composition. Such properties as the hot-working characteristics, machinability, carburizing characteristics, amount of distortion during quenching and the retention of austenite may be considerations of importance in many applications. However, hardenability is one of the most important properties of an alloy steel and one that must be considered in almost all cases involving heat-treatment by quenching. Therefore, a method for determining the lowest-cost alloy combination should be of considerable value. Determination of Most Efficient Combinations For comparing the alloying elements on standards of cost and hardenability, it

Jan 1, 1947

By R. W. Raymond

There is apparently no end to the doubts, inconsistencies and absurdities in which the courts of our mining States and Territories are involved in their attempts to apply to conditions of ever-increasing complexity the provisions of our anomalous mining law. In previous papers, I have called this statute " the law of the apex," because it based upon that vague, novel and mysterious condition the most important grant of title. But the apex is scarcely a more essential feature than the end-lines and the side-lines; for the rights which it may confer may be limited in various ways by these; so that we have, in many a case, the most ridiculous result that the United States, in return for the money of a citizen, conveys to him with much solemnity, under its broad seal, nobody knows what, bounded nobody can tell how. A decision recently made at Butte by Judge De Wolfe, of the United States District Court of Montana, in the case of King et al. vs. The Amy and Silversmith Mining Company, furnishes a fresh illustration of this criticism. The diagram on the following page, constructed without precise regard to courses and distances, simply to assist in the statement of the essential features of the case, will, 1 hope, make clear the principles . involved : The plaintiff occupies a location (the Nonconsolidated) adjoining on the north the defendant's location, a b c d (the Amy), and the disputed mining-ground lies, let us say, in depth under the point W, that is, on the dip of the vein, VD, but not under the surfacelocation, a b c d. The defendant has the prior title, and claims this ground under its extra-lateral right. It is admitted that the apex does not cross the end-line, a d, and does cross the side-line, a b. Whether it crosses, at the other end of the location, the end-line, b c

Jan 1, 1889

By C. S. Matthews, H. M. Girner, C. D. Williams, M. J. Edwardson, H. R. Parkison

Quantitative interpretation of electric logs requires knowledge of formation temperature. In this paper, methods are developed for computing changes in formation temperature caused by circulation of mud during drilling operations. The basis of the method is the mathematical solution of the differential equation of heat conduction. The solution of this equation is presented in a series of graphs. These graphs are used to determine formation temperature disturbance at various radii for arbitrary mud circulation histories. Example comparisons with field results show reasonable agreement. It is concluded that, in general, the temperature disturbances caused by circulating mud are small beyond 10 ft from the wellbore but are quite significant near the wellbore. INTRODUCTION Quantitative interpretation of electric logs requires knowledge of the formation temperature in order to establish the resistivity of the formation water with accuracy. To determine the formation temperature, the temperature disturbances produced by circulating drilling mud must be evaluated. -The objective of this investigation was to develop a method for the numerical determination of these temperature disturbances at any distance from the wellbore as a function of time. The first step was to solve the differential equation describing the temperature behavior in the formation during and after mud circulation. This solution was used to calculate a series of curves relating temperature disturbance to shut-in time for various circulating periods. An "exact" method for computing formation temperatures with the use of these temperature-disturbance plots is described, and the results of an application of this method to a well in Montana are presented. Procedures for approximating formation temperatures are also discussed. BASIC EQUATIONS AND ASSUMPTIONS With the assumptions that (1) cylindrical symmetry exists, with the borehole as the axis, (2) heat flow is 1. The formation can be treated as though it is radially infinite and homogeneous in extent, as regards heat flow. 2. The presence of mud cake can be disregarded. 3. The effect of heat generated by bit action is negligible. 4. After mud circulation ceases, the rate of radial heat flow at the wellbore is negligible and is assumed zero for purposes of calculating temperature change with time. These assumptions are believed to be reasonable because of the agreement achieved between calculated and measured borehole temperature in a well, to be discussed later. Further, the agreement at the wellbore indicates that temperatures in the formation were also approximately correct. since it is the formation temperatures that determine wellbore temperature after ceasing circulations SOLUTION OF THE DIFFERENTIAL EQUATION AND ITS APPLICATION The solution of Eq. 2 for the temperature behavior during and after a single period of mud circulation is

By R. M. Daelen

Mechanical science is severely tested by the demands of the iron manufacture for the varied apparatus needed to transport and to treat raw materials and products. Water has long been a favorite means of transmitting pressure for such purposes, because of its own incompressibility. Further advances in its use are the more to be expected, since mechanical improvements have steadily tended to overcome the difficulties formerly encountered in the employment of great hydraulic pressures. So long as the pressure is not higher than that which requires for plungers, etc., only ordinary stuffing-boxes, with hemp or other similar packing, the necessary arrangements for the production and transmission of the water-pressure without leakage are very simple. But when this limit (which is, for most purposes, 50 kilos to the square centimeter) is exceeded, new conditions of construction arise, which are met in various ways, and which justify a primary division of hydraulic presses into low-pressure and high-pressure respectively. The former are used in lifting and moving weights, and employ pressures as high (in extreme cases) as 100 kilos per square centimeter; but at this point the friction between piston and hemp-packing is so great that the use of cup-leathers is already preferable. Beyond 100 kilos it becomes a necessity. The range of practicable tight packing which follows is considerable, extending to about 1000 kilos; but "high pressure" in practice is from 100 to 600 kilos, and it is to this that the present paper applies. General Classes and Types. Hydraulic transmission at high pressure usually claims consideration in case the solid mechanism, such as levers, cams, screws, and gear-wheels, would have to be too large, would involve too much friction, or could not be suitably adapted to the speed-requirements of the working-tools. Since steam is mostly the primary carrier of

Jan 1, 1893

By E. F. Kingsbury

ONE of the well-known and important uses of the noble or precious metals has been for electrical contacts. In fact, the elements of this group, comprising gold, silver and. the six platinum metals, have been called "noble" because of their ability to resist heat and corrosion, properties which. were early found to be of importance in good contacts. Of these, platinum and its iridium alloys, palladium, and silver, have been extensively used. In recent years the electrical industry has been responsible for about one-eighth of the total consumption of the platinum metals in the United States. Information is not available as to what part of this one-eighth has been used for contacts but it is certainly an important one. SUBSTITUTES FOR PLATINUM During the past 20 years a considerable number of contact alloys have been proposed in the patent literature largely with the aim of more or less replacing platinum by gold or silver, and some of these alloys are finding increasingly widespread application as the reliability of their performance becomes established. From even the partial data at hand it appears that this substitution by the less precious metals has replaced at least one-half of the amount of platinum that the entire electrical industry would otherwise be consuming at the present time. While the subject is of considerable interest to the metallurgist it is even more so to the electrical engineer and it is surprising that the literature records no systematic and' comprehensive investigation along these lines. Practically all the scattered work on noble metal contacts has centered around platinum as a standard and has had two more or less distinct aims. One of these has been the replacement of platinum by cheaper materials, and the other, the development of materials of superior electrical performance. The merit, of a contact metal has been assumed to be dependent on its infusibility, and since the more precious metals have the higher melting points there has naturally been an association of the two qualities in the sense that the more precious were

Jan 1, 1928

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By R. D. Stover, F. O. Shuck

The variation of binary-diffusion coefficients with composition in the liquid Bi-Sn system at 300°C was measured using the capillary-reservoir technique. The experimental coefficients did not exhibit a simple composition dependence. A number of tests were also made to determine the effect of variation of density with composition on convection within the capillaries. These tests indicate that the density changes arising from composition duferences may give rise to high diffusion coefficients unless care is taken to maintain a stable configuration. In recent years there has been considerable interest in diffusion in liquid metals. However, the bulk of the work done to date has involved measurements of self-diffusion or diffusion of dilute concentrations of "solute" metals. Because there are possible applications to liquid phase processing of metal alloys and since additional data may help to clarify the nature of diffusion in liquid metals, investigations of the concentration variation of diffusion coefficients in binary alloys have been undertaken. Of past studies only two have covered large ranges of binary composition. Niwa et al.' investigated the Pb-Sn, Bi-Pb, and Bi-Sn systems and Grace and Derge2 investigated the Bi-Pb system. Because of the discrepancy between the data of these investigators, it was deemed desirable to check the possibility of convection arising from the variation of density with composition. The capillary-reservoir technique of Anderson and saddington3 was chosen for the present investigation since it has been widely used for measurements involving dilute solute concentrations and it was the technique used by Grace and Derge.2 It was necessary, however, to modify the normal procedure of using a pure metal bath to avoid measurement of integral diffusion coefficients over large concentration ranges. The alloy system chosen for study was the Bi-Sn system for which there are some data available.' EXPERIMENTAL PROCEDURE In order to utilize the capillary-reservoir technique for measurements of diffusion coefficients as a function of composition, it was necessary to modify the normal procedure slightly. This modification consisted of using a reservoir composition which was only slightly different from that in the set of capillaries, in order that the integral coefficients measured might be taken over a small composition range and might thereby be assumed to approximate the differential coefficient at some average composition between that of the capillary and that of the bath. It was found that a composition difference of approximately 0.10 mass fraction provided a satisfactory compromise between a small increment in composition and reasonable accuracy in measuring changes of composition. The alloys were prepared from tin and bismuth of 99.999 pct purity. The materials were first cleaned of surface oxides, then weighed and melted to form a homogeneous alloy in a Pyrex filling apparatus. The capillaries used were of precision bore Pyrex tubing 1.000 *0.005 mm bore. Capillaries of various lengths (from 2.85 to 5.85 cm) were cut and sealed at one end by fusing a 3-mm Pyrex rod to the end. The capillaries were filled by inserting them into the filling chamber, evacuating the chamber, submerging the capillaries, and pressurizing the chamber with argon. Two sets of capillaries were prepared for each run. One set contained an alloy more dense than the bath alloy and one set a less dense alloy. This procedure was followed so that the effect of density difference on the measurement could be determined. After filling one set of capillaries, these were placed open end up in a capillary holder and transferred to the diffusion chamber which consisted of a Pyrex tube inserted into a graphite block. The second set of capillaries was then filled and placed into the diffusion chamber. The reservoir alloy, which had been melted in a separate crucible, then was poured carefully into the diffusion chamber. Sufficient reservoir alloy was used to cover all capillaries to a depth of several centimeters. All of these operations: capillary filling, melting of alloys, and diffusion anneal, were carried out in a fused-salt bath which maintained a temperature of 300"*1°C. All capillaries were permitted to diffuse for approximately 48 hr. At the end of the diffusion period the capillary holder was removed from the bath and

Jan 1, 1969

By Wilbur H. Somerton

In order to evaluate the quantitative determination of porosity by various neutron logging systems, four test wells were constructed to simulate some of the possible variab1e.r found in field logging conditions. All of the test holes contain sections of limestone with one section of sandstone included in one well. Each well has a representative section of high, medium, and low porosity. Three borehole sizes are represented by three of the test wells, all containing fresh water. One test well contains saturated brine. Statistical and tune constant checks are made for each system evaluated. Runs and repeat runs are made with the sonde centered and eccentric. Factors evaluated are the effect of borehole size, sonde position, salinity, chemical composition of rock, and statistical variation. A semi-quantitative method of evaluation of these effects is used giving the average maximum per cent error possible for each. Drift and calibration procedures are also discussed. The effect of the various factors appears to be largely a function of the phenomena detected as well as the means of detection. Graphic illustrations of some of these effects are presented. It is concluded, that for accurate log interpretation, the hole size and sonde position should be known. INTRODUCTION The use of neutron logs for the derivation of porosity has become an accepted practice in many areas. In recent years, many different neutron logging systems have been offered to the industry. The neutron sources presently available are of the radium-beryllium or polonium -beryllium type. Detector types used are ionization chambers, Geiger-Mueller-type counters, proportional counters, or scintillation detectors used to detect or measure gamma rays, thermal neutrons, epithermal neutrons, fast neutrons or combinations of these. It is well-known that all systems do not respond alike in all environments. As a result, testing facilities and an evaluation method were developed for use in evaluating the porosity discriminating ability of neutron logging systems using conditions simulating those normally encountered in the field. With such an evaluation, the suitability of a logging system can be determined lor selected field conditions. TEST FACILITIES The testing facilities consist of wells containing rocks of various porosities, constructed to include as many parameters as practicable. Three pits were drilled to a depth of 20 ft and the fourth to a depth of 9 ft, all having 48-in. diameters. Rat holes were dug to a depth of 6 ft in the center of each pit and fitted with sections of pipe having appropriate diameters. The top of this pipe was located approximately 8 in. above the pit bottom. A 6-in, layer of cement was then poured on the bottom and while still wet, 42-in. OD corrugated, galvanized culvert pipe was set on bottom and centered in place. This pipe extends approximately 1 ft above the surface of the ground. The annulus around the culvert pipe was then filled with cement to the top. A 1- or 2-in. layer of sand was placed on the cement bottom to provide an adjustable bed on which to place the series of rocks set in each hole. A cross section of a typical test well containing the porous rocks is shown in Fig. 1.

By M. N. Pathasarathi, P. A. Beck, T. J. Koppenaal

EARLIER work1 indicated that in rolled and annealed copper the volume fraction of the cube-texture component may increase on continued isothermal annealing. Merlini found2 that in rolled copper the well-known increase in the amount of cube-oriented material with increasing annealing temperature3 is concurrent with grain growth, which takes place after recrystallization is complete. It was found that both in copper2 and in aluminum4 the texture resulting from primary recrystallization, even if this is followed by some grain growth, may in general comprise, in addition to the cube-texture component, four symmetrical texture components of the general type (123)[412], i.e., components not very far from the ideal orientations of the rolling texture. The volume fraction of the cube-texture component increases on further annealing at the expense of these four components.' The present work was undertaken to study quantitatively the increase in the volume fraction of the cube-texture component in the course of normal grain growth, under varying conditions. Since the grain-gr3wth behavior of A1-Mn alloys has been already investigated in some detaiL5 an A1 + 0.8 pct Mn alloy was chosen for this work, in which the extent of normal grain growth can be effectively controlled by the inhibiting effect of a dispersed second phase. EXPERIMENTAL PROCEDURE High-purity aluminum of the following composition was used: A1 99.997 pct, Cu 0.0004 pct, Fe 0.0005 pct, and Si 0.001 pct. A high-purity A1-Mn master alloy was prepared by dehydrating manganese chloride at 500°C and reacting it with molten high-purity aluminum at 750°C in a graphite crucible.5 The Mn metal reduced from the salt by the molten aluminum goes into solution in the latter. The master alloy? containing 13 pct Mn, was solidified under conditions suitable for minimizing segregation. An ingot of the final alloy, to be used in the experiments, was per pared by melting high-purity aluminum and the necessary amount of master alloy in a graphite crucible, and by pouring the molten alloy into a graphite mold preheated to 700°C through a box containing graphite baffles designed to intercept most of the aluminum oxide films floating in the melt. The melt was then solidified by placing the mold on a water-cooled copper plate and by keeping the top of the mold hot, in order to minimize piping. The 6 1/2 in. long, 11/4-in.diam ingot consisted largely of a single crystal. Chemical analysis showed that there was little segregation from the bottom (0.83 pct Mn) to the top (0.81 pct Mn). Spectrographic analysis of the ingot showed that the impurity content remained essentially the same as that of the aluminum used. The ingot was processed so as to obtain a uniformly small grain size. without banding. The ini-tial steps of rolling in the form of a flat bar and of annealing, down through a thickness of 0.4 in., are shown in Table I. At this point the bar was cut into four sections, each approximately 3 in. long, which were processed separately as shown in Table If. The table also gives the penultimate grain sizes obtained in each section by annealing prior to the final rolling of 90 pct RA. During the final rolling the strips were reversed end to end between passes. Annealing treatments were given in a salt pot furnace, with the temperature controlled to 1°C. All annealing of section "6s" was carried out above the solvus point to avoid the formation of second-phase precipitate. The penultimate annealing was sufficiently short to give a relatively fine grain size in spite of the high temperature. Section "6L" was processed in a similar manner, except that the penultimate annealing was much longer, so as to allow considerable grain growth. Section "4" was given the two final

Jan 1, 1961

By G. S. Cole, G. F. Bolling

ThE exact type of fluid flow which occurs in a solidifying ingot is important in determining subsequent grain structure. This has been shown in studies of natural Convection" and of forced stirring or other disturbances of the melt."16 We shall explicitly argue that a complement to the existing natural flow in an ingot should be more effective than other types of flow in promoting the columnar-to-equiaxed transition. The ultimate effects of fluid flow upon structure is one of the topics of solidification that we have investigated in the alloy system Pb-Sb, under conditions simulating casting. In Fig. 1, the essential features of a bidirectional growth apparatus are shown; horizontal freezing from water-cooled faces within a low-thermal-conductivity lavite boat is a reasonable simulation of an ingot section. Details such as the furnace and thermocouples are omitted in order to show the location of four permanent. magnets, each with a pole separation of 21 in. providing a central field of about 1000 Gauss. When coupled with a dc current imposed through appropriate connections made at the cooled faces, a flow of fluid is produced as shown schematically. This technique described by Pfann and ~orsi" is ideal for our purpose since the flow indicated is the same as that we observe to occur naturally in this system. Components of 99.999 pct purity were used for study and all due precautions were taken in alloy preparation to avoid contaminants. Sections of the specimens were taken to ensure results representative of the interior as well as the surface of specimens. All proportions of equiaxed and columnar regions were measured by tracing the etched grain structures onto graph paper and simply counting squares. Four alloys were examined at superheats of 40" * 5°C and 100" * 9°C. Preliminary tests had shown that no appreciable enhancement of structure was obtained with magnetic field alone, so that this condition is not reported; it should nevertheless be noted that other configurations of magnetic field will reduce convection and thus enhance columnar growth.'8 For the tests reported the magnetic field was applied to a specimen by bringing the four preassembled magnets to a position 2 mm from an outer tube immediately after the ingot was poured. The dc current of 30 amps passed through the sample throughout the entire solidification cycle, resulting in a power dissipation of 9 w per sq cm of interface. This may be compared to the evolution of latent heat of approximately 18 w per sq cm. Table I contains the results of this experiment in terms of the total area ratio, equiaxed/columnar grains, as a function of the field interactions, solute concentrations, and superheats employed. The total structure of the ingot is seen to be most influenced when both the field and current are applied simultaneously; when current acts separately, little effect may be noted in spite of the heat supplied. In addition, the change in structure from the no field-no current case to the field-current condition is more pronounced at the higher superheat, and the higher the concentration of antimony. An example of the grain refinement, as well as the increased equiaxed zone, is shown in Fig. 2. It is now important to prove that there is indeed an increase in fluid flow due to the presence of the field-current interaction; this is done by temperature measurements in the liquid metal. Let us consider a bidirectional casting in which heat is applied to and removed from the system, in such a way that rate of solidification is zero.* When a sensitive thermocouple

Jan 1, 1967

By Butler, P. B.

TRIPOLI is a rather unusual form of silica, which thus far has been found in commercially valuable quantities only in the neighborhood of Seneca, Mo., although there are numerous deposits of somewhat similar materials in several southern states. The latter have not, however, attained any position of real importance, due undoubtedly to definite structural limitations which have rendered them less suitable for the particular uses that have given tripoli its principal outlets. Raymond B. Ladoo, mineral technologist, says': "Since that time (1880-90) the term tripoli has with increasing definiteness been reserved for the Seneca material, and other siliceous materials of similar origin and physical properties."

Jan 1, 1928