Search Documents

By J. N. Sicking, F. H. Brinkman

A new method for obtaining equilibrium vaporization ratios (K-values) for reservoir fluids has been developed and tested. By application of the method, complex experimental measurements of liquid and vapor phase compositions are eliminated. This simplified technique reduces the cost of experimental equilibrium-ratio data for reservoir studies of condensates and volatile crude-oil systems. The method is designed for systems of constant composition and, therefore, is best suited for depletion studies where compositional changes at high pressures are minor. The basic data required, in addition to the composition of the initial reservoir fluid, are the relative vapor-liquid volumes and densities at reservoir temperature and variom reservoir pressures. Tests demonstrated that the method predicts equilibrium ratios accurately for condensates. A single test on a crude oil was not conclusive; further testing will be necessary before the accuracy of the method can be determined for crude-oil systems. In addition to determining equilibrium ratios, the calculation method provides information on the physical properties of the "plus" component in the vapor and liquid phases. The "plus" component is that mixture of components heavier than the least volatile fraction analyzed. This information is useful in studies of both natural depletion and cycling operations for condensate reservoirs where the heptanes-plus component in the gas phase is produced from the reservoir. INTRODUCTION As more volatile oil and condensate reservoirs are found, the use of phase behavior techniques to predict their performance is increasing in importance. These techniques have long been used for condensate fields and have more recently been applied to crude-oil fields containing oils of medium-to-high volatility. In these phase behavior methods, equilibrium ratios (K-values) are used to predict compositional changes in the reservoir fluids—thereby accounting for the recoverable oil that exists in the gas phase. The reliability of the predictions depends to a large extent on the equilibrium ratios used. These values must be obtained for each component for the entire pressure range being investigated. Unfortunately, because of the complex nature of hydrocarbon mixtures, accurate K-values are hard to obtain. The equilibrium ratios for a particular component will vary not only with the temperature and pressure, but also with over-all composition of the system. The importance of composition is quite critical at elevated pressures, but becomes negligible at pressures below about 300 psia. Therefore, because most phase behavior problems involve the high-pressure region, each fluid system becomes a special case. Experimental programs to determine characteristic K-values are quite difficult and time-consuming. Thus, it is often necessary to resort to approximations of the K-value data. Charts giving K-values for various mixtures and classes of mixtures are available in the literature. However, there are two major difficulties in using them: (1) the K-values of the "plus" component (that mixture of components heavier than the last one analyzed) must be obtained by extrapolation from the K-values of the other components; and (2) the K-values obtained must finally be adjusted by trial and error to agree with observed volumetric data. To eliminate these difficulties, a new method of determining equilibrium ratios was developed. Briefly, after the composition of the system as a whole has been analyzed, the method uses empirical correlations and the gross fluid properties of the system (relative vapor-liquid volumes and densities) to calculate K-values. Because the calculative procedure is long, it is best solved on a digital computer. About one hour of machine time on an IBM 650 computer is required to develop a K-chart for the fluid being examined. DEVELOPMENT OF THE METHOD OF OBTAINING K-VALUES Equilibrium ratios are defined as the ratio of the mole fraction of a component in the vapor phase to its mole fraction in the liquid phase. This statement is expressed in Eq. 1. A typical plot of equilibrium ratios for a particular system is shown in Fig. 1. It should be noted that, at pressures near the saturation pressure, the K-values appear to converge to a common point. This apparent convergence point is called the convergence pressure and is a characteristic of the system involved. Various empirical correlations of K-values have been noted. It has been observed that an isothermal plot of

By C. S. Barrett, D. B. Masson

Martensitic transformations have been found in AgCd both upon cold-working at room temperature and cooling to lower temperatures. The crystal structures of the transformation products were found to be close-packed hexagonal in the first case and or-thorhombic in the latter. The transformation characteristics also were studied. Similar treatment of AuZn alloys failed to yield any transformation. THE literature on martensitic transformations of body-centered cubic metals and alloys indicates widespread instability of this structure at low temperatures, a tendency which merits further study. The body-centered cubic ß-phase of CuZn, for example, when it contained less than 42 wt pct Zn, was found by Greninger and Mooradian' and others' to transform on cooling to subzero temperatures to a phase that was tentatively considered to be tetragonal. Further work by Massalski and Barrett" demonstrated that cold work at low temperatures causes a partial transformation of ß CuZn of higher Zn content. The structures of the strain-induced transformation products were found to be different from those induced by simple cooling. Another well-known martensitic transformation among body-centered cubic phases is that of ß AuCd, first studied with X-rays by Olander,' then very thoroughly by Chang and Read.5,6 Here again transformation was found to occur both as a result of cooling and of strain. The alkali metals Li and Na, as well as certain Li-Mg alloys, also undergo transformation from their normal body-centered cubic structure, both on cooling and on cold-working. The phase AgCd, the subject of the present report, should be expected to behave quite similarly to CuZn for a number of reasons. It is the chemical analogue of CuZn, silver being directly below copper and cadmium directly below zinc in the periodic table. The size factors (percent difference in size) of the atoms, possibly a consideration in the stability of the ß-phases, are +3.1 in AgCd and + 4.2 in CuZn. Likewise the relative electronegativities of the two pairs of metals are about the same, CuZn possessing an electronegativity difference of 1.0 and AgCd one of 0.8. These values are from a table of electronegativities given by Darken and Gurry." The phase diagrams of the two systems around 50 atomic percent are similar, both possessing a disordered body-centered cubic phase, ß, at high temperatures and an ordered bcc phase, ß, at room temperature; however, the ß and ß' phases of AgCd are separated by a hexagonal phase, [, stable in the range 220-440oC, which has no analogue in CuZn. There has been confusion in the literature as to the structures of the ß' and [-phases. The phase diagram in the ASM handbook'" has the structures of the two phases interchanged; however, Hansen" reports the correct relative positions and Muldawer" verified that ß', the low-temperature phase, is body-centered cubic. Work by the present authors also

Jan 1, 1959

By W. F. Stowasser

downdraft traveling grate process to agglomerate pelletized iron ore concentrates has been successfully demonstrated in a pilot plant at Carrollville, Wis. Work there followed several years of development in the Allis-Chalmers Mfg. Co. laboratories, and the pilot plant phase was carried out in cooperation with Arthur G. McKee & Co., consultants and engineers to the iron and steel industry. End result of the process is conversion of iron ore concentrates into a form which can easily be transported and smelted in the blast furnace. Process Description The first of two process steps incorporates the art of balling and prepares the concentrates for burning. The second step consists of burning the green balls on the grate machine to the hardness required for shipping and handling purposes and for reduction in blast furnaces, see Fig. 1. Facilities are provided at the pilot plant to receive carload quantities of concentrate. The concentrates are loaded into a 50-ton bin direct from railroad cars. Because of the variable moisture content of the concentrates after shipment in an open railroad car it is necessary to repulp and refilter the concentrates to maintain a uniform and proper moisture content for the balling operation. Concentrates are conveyed to slurry tanks, and the slurry, at 50 to 60 pct solids, is pumped to a 4x4-ft drum filter. The filter provides feed of uniform moisture to the plant. Magnetite concentrates are normally filtered to produce a cake containing about 10 pct moisture, a necessary requirement for the following balling operation. The filtered concentrate is conveyed to a rotary bin table feeder which acts as a surge bin for the filter cake and delivers a steady flow of concentrates to the balling drum. It is often desirable to make additions to the concentrates as they are fed to the balling drum. These additives, such as bentonite, increase the strength of the finished green pellet and improve ballability of the concentrate. A vibrating feeder supplies additive to the feed belt, and the additive is mixed with the concentrate in the balling drum. The balling drum, shown in Fig. 3, is 8x3-ft diam. An oscillating cutting bar maintains the lining in the drum by trimming off the buildup of excess concentrate as it forms. The drum is operated in closed circuit with a lx4-ft rod-deck vibrating screen. Undersize pellets or seed pellets from the screen are returned to the balling drum until they grow to the desired size. Size of pellets is controlled by the opening in the screen deck. The formation of pellets in the balling drum is affected by many variables. Some of these are: the size distribution of the feed, the particle shape of the concentrate, the feed rate to the drum, the moisture in the concentrate, the speed of rotation of the drum, the slope of the drum, and the type of trimming obtained with the cutting bar. In this process, attempts are made to control the pellet size within the limits of % to 5/8 in. diam. The screened oversize pellets are conveyed under a coal feeder where sufficient powdered coal is added to the belt to produce desired results in the burning process. The top size of the coal successfully used has been 20 mesh, and anthracite was used in the test program. Fig. 4 illustrates the vibrating screen and the coal feeder. The pellets and free coal are conveyed together to the 5x3-ft diam- reroll drum that rolls the coal onto the surface of the pellets. This drum is also equipped with a cutting bar. The prepared pellets, containing bentonite, water, and surface coal, are elevated to the traveling grate, which consists of a continuous strand of 37 pallets. Each pallet, with a grate bar area 2 ft wide by 1 1/2 ft long, has 14-in. high side plates, Fig. 5. Feeding and distribution of the green balls to the grate is handled by a short conveyor which oscillates back and forth across the 2-ft width of the grate. An adjustable vertical plate located several inches in front of the head pulley of the oscillating conveyor controls the height of the bed and levels the moving bed of pellets. This method of feeding prevents segregation of various size pellets as well as fines and produces a uniform, permeable bed. The pallet train moves under the furnace and across four windboxes, located beneath the pallet frames, see Fig. 2. As the green pellets are deposited on the grate, partial drying of the pellets begins over a 2-ft long updraft windbox. The low temperature air reduces the moisture in the pellets in the lower level of the bed and this operation is essential to prevent sagging of the bed during later stages of the Process. The air used for this drying is recuperated from cooling the pellets on the grate, and supplemental heat, required for starting the Process, is obtained from an auxiliary burner. The pellets are then moved by the grate into the furnace and over an 8-ft windbox, designated as the downdraft waste windbox. Products of combustion are exhausted from this windbox to atmosphere. The furnace, shown in Fig. 6, is constructed with three chambers to provide downdraft drying, preheating, and ignition, respectively, to the pellet bed as it passes through. Overall length of the furnace is 5.57 ft; however, the exterior wall ends may be moved to reduce the length and also adjusted to Obtain the bed height desired, The drying, preheating, and ignition sections of the furnace are supplied with medium temperature

Jan 1, 1956

By R. Schuhmann

Available thermodynamic data applicable to copper smelting systems are collected and tabulated, and the important gaps are pointed out. A few examples are given of estimations which can be made from the available data. An experimental research program is proposed to supply the thermodynamic data that appear most essential to better quantitative understanding of the chemistry of copper smelting. The proposed program is designed also to shed specific light on the practical problems of slag losses and magnetite behavior. OPPER smelting, from flotation concentrates to V-/ blister copper, is conspicuous among the large scale chemical processes which are conducted with only relatively incomplete knowledge of the physical chemistry involved. For example, no common metallurgy text explains adequately why copper enters the matte phase while iron enters only to the extent that sulphur is left over after satisfying the copper. Explaining this important phenomenon as a manifestation of the greater affinity of sulphur for copper than for iron is unsound because the affinities of copper and iron for sulphur are about the same at smelting temperatures. As will be shown, other affinities are really decisive in the relatively clear-cut separation of copper in the matte. In contrast, thermodynamic studies have contributed much to our understanding of copper refining, zinc oxide reduction, magnesium production, steelmaking, etc. For each of these processes, the important reactions are clearly recognized, and fair to good quantitative values of the free-energy changes and equilibrium constants are available. Such data have proved to be of constantly increasing practical value in process development and improvement. Work in other fields has furnished much thermodynamic data applicable to copper smelting systems. In fact, several promising starts have been made in applying such data to specific smelting problems. Kelleyl made an appraisal of the possibilities of recovering elementary sulphur from low grade matte. His calculations and compilations of thermodynamic data have represented the starting point for much of the work in this field, including the present survey. Huang and Hayward2 nd Aksoy3 used thermodynamic methods in the study of copper losses in reverberatory slags. Peretti4 used thermodynamic data in explaining the chemistry of converting. The recent publications of Darken and Gurry"." and of Darken,' dealing with the iron-oxygen and iron-silicon-oxygen systems, respectively, present equilibrium data that are applicable to copper smelting systems. Also additional data were reported recently on the affinity of sulphur for copper, manganese, and iron8 and on the sulphur pressures of iron-sulphur melts." The survey presented in this paper was made as the basis for planning an experimental program on the thermodynamics of copper smelting. Few researches on the chemistry of copper smelting have been reported in recent years, so that a reappraisal and coordination of old and new data are essential if further work is to take the directions of maximum value. The experimental program is now in progress, and the plan of attack is outlined at the end of this paper. Progressive Oxidation and Desulphurization of Copper-bearing Liquid Phases: The chemical activities of sulphur and oxygen are two of the most important thermodynamic yardsticks to be applied to copper smelting processes. Virtually the entire smelting and refining sequence involves a series of systems characterized by decreasing sulphur activity and increasing oxygen activity. In this section, therefore, an attempt is made to define and explain these activities in terms of equilibrium partial pressures of SO2, s2, and O,. Also, estimates of these quantities are presented, the estimates being based largely on calculations presented in a later section of this paper. The sequence of steps from raw flotation concentrate to fully oxidized copper ready for poling involves progressive and controlled oxidation. Iron is oxidized and enters the slag. Sulphur is oxidized and leaves in the gas. Table I summarizes several important features of this oxidation and desulphurization sequence, starting at the beginning of the matte blow in the converter. The top line gives in order the principal smelting and refining stages up to fully oxidized copper, plus the additional step, not used commercially, of oxidizing all the way to Cu,O. In the second line are shown the principal copper-bearing liquid phases which characterize the process. Through most of the sequence the copper

Jan 1, 1951

By F. George, W. Tice, M. Salkind

It was found that Al-A13Ni could be readily cold rolled perpendicular to but not parallel to the whiskers. Reductions of more than 98 pct were achieved without cracking by rolling perpendicular to the whiskers, whereas extensive edge cracking was noted after only 15 pct reduction when rolling parallel to the whiskers. The longitudinal and transverse tensile strengths were nearly doubled, and the longitudinal yield strength more than tripled by cold rolling 50 pct in a direction perpendicular to the whiskers. The whiskers exhibited some waviness (elastic bending) as a result of cold rolling, but at very high reductions (greater than 75 pct) whisker fracture and misalignment became significant. A fine dislocation substructure in the matrix consisting of cells attached to the whiskers was pro -duced by cold rolling. Most of- the substructure was readily removed by a 1-hr anneal at 500°C. Cold rolling was found to substantially reduce the thermal stability of the microstructure at 610°C but did not affect the stability at 500°C. FIBER and whisker reinforced composite materials promise significant improvements in properties over conventional materials. Before they find wide use, however, it will be necessary to understand the response of these highly anisotropic materials to common metalworking processes. Most of the nonmetal-lic fiber reinforced materials have very low elongations (a few pct or less) in the direction of fiber alignment. Thus, metalworking techniques such as rolling and forging would not be as broadly applicable to these materials. This investigation was initiated to determine how a composite system consisting of Al3Ni whisker reinforced aluminum responded to rolling, what changes in the microstructure occurred, and the effect of deformation on the mechanical properties. The composite material studied was produced by unidirectional solidification of the A1-Al3Ni eutectic alloy'-7 and consisted of 10 pct by volume of aligned whiskers of Alai in a matrix of aluminum. It should be pointed out that this system is not representative of all composite materials, and the results will therefore not be universally applicable. The A1-Al3Ni system is characterized by: 1) A strong fiber-matrix interfacial bond 2) A ductile matrix 3) A sufficiently low fiber content to allow significant plastic flow between fibers 4) Strong, completely elastic whiskers (tensile strength 400,000 psi, elastic modulus = 20 X 106 psi.1 These factors allow the material to be readily rolled perpendicular to the fibers. If the fiber-matrix bond were not strong, such a weak interface could fail during rolling. A measure of the ability of a composite to be rolled in the transverse direction can be obtained from noting the transverse tensile behavior. In the case of Al-Al3Ni,2 there is considerable ductility (15 to 30 pct). In the case of boron filament reinforced aluminum, for example, the transverse elongation is less than 1 pct,8 and the material could probably not be cold rolled as readily in that direction. EXPERIMENTAL PROCEDURE 3-in. diam ingots of A1-A13Ni eutectic were unidi-rectionally solidified in graphite crucibles. The starting materials consisted of 99.99+ pct pure nickel and aluminum, and the pure eutectic ingots were made with 6.2 wt pct Ni. The unidirectional solidification process (described in detail elsewhere1-3) consists of preparing a master heat of eutectic composition, remelting, and withdrawing the ingot vertically downward through the heat source at a controlled rate so that plane front solidification proceeds upward at a constant velocity. The resulting microstructure consists of 10 pct by volume of whiskers of very high aspect (length to diameter) ratio. The fiber lengths have not been measured because of the difficulty of detecting fiber ends9 but exceeds 104. There is some possibility that the fibers may be continuous within one grain. Flat sheet specimens 2¾ in. sq and approximately 0.2 in. thick containing whiskers parallel to the plane of the sheet and to one edge were used for this study. A1-A13Ni exhibits either a rod-like (high solidification rates) or a blade-like (low solidification rates) whisker morphology,1,3 and both types were studied. Rolling was accomplished using a two-high rolling mill at a speed of approximately 10 fpm. The rolling direction was either parallel to or perpendicular to the direction of growth (direction of whisker alignment). Reductions of from 0.002 to 0.03 in. per pass were used with the most common value being 0.005 in. per pass. Cold rolling of Al-Al3Ni to more than 98 pct reduction in thickness was accomplished with no intermediate anneals. In addition. a series of speci-mens was cold rolled 97 pct with a 1-hr, 500°C anneal in air after each 50 pet reduction. Tensile testing was accomplished using a Tinius-lsen four screw testing machine. Flat sheet specimens + in. wide and between 2 and 2; in. long with the thickness dependent upon rolling reduction, were used. The gage section was in. wide and 1 in. long. Strain was measured using a clip-on LVDT extensome-

Jan 1, 1970

By G. W. Tracy, R. D. Carter

Numerical calculations were made to determine the behavior of reservoirs with high-pressure drawdown and wide well spacing where the initial productivity is low and the wells are completed by hydraulic fracturing. The two-phase flow equations were solved for the flow into a single well. This well was assumed to be producing from a reservoir with hydraulically created horizontal fractures (four different systems with fractures were studied). For comparison purposes, additional two-phase flow calculations were made assuming a reservoir with uniform rock properties. The two-phase flow results were also compared with the conventional calculation methods, which do not include the effect of saturation gradients resulting from a simultaneous flow of oil and gas which are normal to this type reservoir. It was found that the conventional methods predict (1) a high and too optimistic value of ultimate recovery, (2) a high producing rate and a high reservoir pressure at a given oil recovery and (3) a low trend of gas-oil ratio with oil recovery. Included in the two-phase flow calculations were provisions to control the oil production rate by an allowable rate and, also, by a gas-oil ratio penalty rule. For the systems with hydraulic fractures, the producing rate was controlled by the gas-oil ratio penalty rule for most of the life. This is in contrast to the system with uniform rock properties which went "on decline" almost immediately. An unexpected characteristic of the systems which included fractures was the early rise in producing gas-oil ratio from 730 cu ft/bbl to approximately 1,200 cu ft/bbl, followed by a "leveling off" before the normally expected gas-oil ratio rise began. Additional features which are a result of hydraulic fracturing are (I) greater ultimate recovery, (2) higher average producing rates and (3) a lower average reservoir pressure at a given oil recovery. INTRODUCTION Some oil fields discovered during the past few years are producing from certain volumetric ally controlled reservoirs (often referred to as solution or internal gas- drive reservoirs) which are characterized by high-pressure drawdown at the wells. Since the available pressure drawdown at a well is limited by the static reservoir pressure and the producing rate is controlled by the available drawdown, wells completed in this type of reservoir usually produce at a rate less than the allowable from the time of completion. Because of this, this type of reservoir is referred to as a low productivity reservoir. Economic considerations require the use of wide well spacing and well stimulation by hydraulic fracturing to make commercial wells in this type of reservoir. Performance predictions for volumetrically controlled reservoirs have been made using a combination of two standard equations. 1. The "Schilthuis" or "Muskat" type material balance equation is used to relate the average reservoir pressure and the cumulative oil recovery. 2. The results from the material balance equation and the productivity factor as described by Pirson' are used to relate the cumulative recovery with producing rate and time. The material balance equation assumed uniform pressure and liquid saturation conditions throughout a reservoir. The steady-state radial flow formula allows for a pressure gradient toward a well but assumes uniform liquid saturation. These calculation methods are adequate for application to reservoirs wherein the drawdown at the well to realize satisfactory producing rates is small compared to the total pressure. In low productivity, volumetrically controlled reservoirs, the pressure drawdown at the well is large cornpared to the total pressure. Although a precise number cannot be given for the magnitude of a large pressure drawdown, values in excess of 1,000 psi would definitely be included. For practical considerations, this usually occurs when the formation flow capacity is less than about 100 md-ft. However, this limit of formation flow capacity will vary with the well producing rate. The low pressure in the neighborhood of the well which results from a high drawdown causes evolution of large volumes of gas. This causes the gas saturation to be higher near the well than at a greater distance—-hence, a non-uniform gas saturation. Also, the relationship between the relative permeability to oil (K/K) and gas saturation is nonlinear but decreases approximately in an exponential way with increases in gas saturation. Because of this, the following chain reaction is established.

By A. Taylor

NICKEL-RICH alloys hardened with small additions of titanium and aluminum and centered around that region of face-centered-cubic primary solid solution, 7, where the atomic ratio of nickel chromium is about 3 to 1, form an important series of high temperature materials because of their resistance to oxidation, high temperature strength, and excellent creep characteristics at elevated temperatures.' With suitable heat treatment it is possible to precipitate a phase based on the ordered face-centered-cubic y' phase, Ni,,Al, from the randomly ordered nickel-rich y face-centered-cubic primary solid solution. By adjusting the ratio of aluminum to titanium the precipitation of needles of the hexagonal intermetallic compound n-NiaTi may be effected. In the present investigation, the main interest was focused on the interrelationships among the y, y, and 7 phases. By using alloying elements of high purity and a suitable melting technique the presence of carbides and nitrides could be completely obviated, although it is realized that their presence is probably essential in alloys of commercial importance. As a preliminary to the study of the Ni-Cr-Ti-A1 system, it was necessary to establish the constitutional diagrams of the three contiguous systems, Ni-Cr-Al, Ni-Ti-Al, and Ni-Cr-Ti, which together form the nickel-rich corner of the Ni-Cr-Ti-A1 quaternary tetrahedron. Accounts of this work on the ternary systems have already been published by the author. A preliminary disclosure of the author's investigations on the ternary and quaternary systems has been made by Hignett2 and has since stimulated work in the same field by Nordheim and Grant." Before the detailed account of the quaternary system, a brief description will be given of the three contiguous ternary diagrams on which it is ultimately founded. Ni-Cr-Ti System The 750° and 1000°C temperature isothermals of the Ni-Cr-Ti system as determined by Taylor and Floyd' are shown in Figs. 1 and 2. The single phase fields of greatest interest are occupied by the extensive face-centered-cubic y primary solid solution of chromium and titanium in nickel, and the close-packed-hexagonal Daltonide, n-Ni3Ti, from which tie-lines radiate across the very wide y+n two-phase field. The chromium-rich primary solid solution is represented by a. As may be seen from the diagrams, the extent of the y phase field increases quite appreciably as the temperature is raised from 750" to 1000°C. Isoparametric lines for the y phase are shown in Fig. 1. They are interesting in that they are almost parallel to the y/r+n boundary. Thus the determination of the tie-line directions is entirely dependent on the exact stoichiometry of composition of the 7 phase. Ni-Ti-Al System The 750°C isothermal section of the nickel-rich portion of the system Ni-Ti-A1 as determined by Taylor and Floyd is shown in Fig. 3.' The regions of greatest interest are the extensive y primary solid solution of titanium and aluminum in nickel, the y' Berthollide phase field based on the ordered face-centered-cubic structure of Ni3Al, and the hexagonal Daltonide phase, n-Ni3Ti. As may be seen from Figs. 3 and 4 the area occupied by the y phase is substantially the same at 750°C as at 1000°C, but the area of the 7 phase is considerably greater at the higher temperature. The tie-lines radiate from n-Ni3Ti across the y+v and y' + v two-phase fields and are evenly distributed

Jan 1, 1957

By G. L. F. Powell, L. M. Hogan

Samples of silver and Ag-O alloy, 0.12 wl pet, have been undercooled to a maximum of 250°C by melting in a slag of commercial soda-lime glass. Grain refinement occurred in undercooled silver samples whet the degree of undercooling exceeded a critical value which varied from 153° to 175°C, depending on the melting conditions. In under cooled Ag-0 samples, the grain structure was fine and equiaxed at degrees of undercooling larger than 50oC. The grain refinement in both silver and Ag-0 alloy samples was the result of recrystallization during or immediately following freezing. When the oxygen content was increased, the degree of undercooling at which recrys-tallization occurred decreased. INVESTIGATIONS of the grain structure of strongly undercooled melts of nickel and cobalt1-4 have revealed a change in room-temperature grain size as a function of undercooling. At large degrees of undercooling the grain size was fine, but samples undercooled by smaller amounts exhibited a much coarser grain structure. The reported undercooling at which this grain size transition occurred in nickel varied between 140° and 175'C undercooling. Walker1 attributed this grain size change to an enhanced nuclea-tion rate. Cavitation at a melt-solid interface was con sidered to generate a high-pressure wave. This, in turn, produced nucleation in the liquid as a result of an elevated freezing point increasing the undercooling in the melt. A similar grain size transition was observed in undercooled silver between 133° and 153°C undercooling.5 The grain size transition in undercooled silver was found to be dependent on oxygen con tent. More recently, the authors5 showed that a simila transition occurred in an undercooled Cu-O alloy, =0.08 pet, but not in oxygen-free copper undercooled more than 200°C. The transition was attributed to recrystallization of the solidified grains after freezing; the greater the degree of undercooling, the more complete the recrystallization. In view of this effect of oxygen content on grain size transition, additional undercooling experiments were carried out with silver. This paper reports the results of these studies on silver and Ag-O alloys undercooled more than 50°C EXPERIMENTAL 1) Materials. The silver was supplied by Matthey Garrett Pty., Ltd., as fine granulate, silver mini' mum 99.9 pet, and contained the trace impurities shown in Table I. The silver originated from two different refineries resulting in the difference in impurity content shown in Table I. However, the variation in composition had no discernible effect on the undercooling behavior. Samples of the silver were melted in an open-ended, vertical, cylindrical resistance furnace, wound with Kantha] wire, the temperature of which was adjusted by means of a variable transformer, 2) Melting and Undercooling. Bulk samples of silver were undercooled by preoxidation and removal of oxidized impurities in a glass slag, as previously described,5 but special precautions were necessary to allow comparison between oxygen-free silver and a Ag-O alloy. Samples free of oxygen were prepared by first melting weights of granulate varying from 200 to 400 g in clean vitreous silica crucibles in air for approximately 15 min. A sample was frozen and a complete glass cover formed over the top surface by adding granulated glass rod. The sample was then melted and frozen several times until no oxygen bubbles appeared in the glass slag. Subsequent thermal analysis indicated that the oxygen content was negligible. The glass acted as an efficient barrier to absorption of oxygen from the air. Ag-O alloys were prepared by melting silver in silica crucibles with only a partial cover of glass, so that the top surface of the melt was in contact with air. The silver was held molten in air for several hours at 1000° to 1050°C, in the expectation that the oxygen in solution would reach equilibrium with atmospheric oxygen. At T - 1000°C the equilibrium oxygen content was calculated as 0.12 wt pet O, using Sieverts law and Eq, [l], derived by Mizikar et a!.7 from the data of Sieverts and Hagenacker8 for 1 atm of oxygen:

Jan 1, 1970

By L. T. Leyson, U. C. Tainton

Some time ago, at ameeting of the Institute Prof. J. W. Richards1 said, "I take exception to the statement that all the factors in the production of electrolytic zinc were known long ago.... There is possible in my opinion an improvement of perhaps 50 per cent. in the new electrolytic processes." An examination of the literature of the subject will show the justness of Professor Richards' contention. The work of the earlier investigators was carried on in the shadow of difficulties that, today, are hardly more than memories. We seldom hear now of zinc sponge, that bête noir of the electrolytic-zinc pioneers. Zinc sponge was the name given to a peculiar, soft, black, non-adherent form of zinc deposit that was utterly useless for melting into ingot form. At the big plant at Cockle Creek, New South Wales, in 1897, Edgar Ashcroft2 said that the solution in the plant would suddenly, and without ascertainable cause, go' "bad" and begin to deposit spongy zinc. The most delicate, even spectroscopic, methods of analysis were unable to detect any difference between "good" solution and "bad" solution; either form might change to the other on being kept for a while. When it is added that an outbreak of this insidious disease (which appeared to be infectious, or at least contagious) could be dealt with only by discarding the solution and washing out all tanks and pipe lines, some idea may be gathered of the troubles of the zinc electrometallurgist in what may be spoken of as the "sponge age" of electrolytic zinc. Thanks to the efforts of a number of investigators, we are today able to diagnose with considerable certitude the nature of the malady that puzzled Ashcroft and his co-workers. The researches of Mylius and

Jan 1, 1924

By Frank Clemes Smith

The study of the so-called refractory gold-ores of the Potsdam sandstone, ores which are probably of wider occurrence and of much greater economic importance in the Black Hills than is generally supposed, has led the writer to formulate in the present paper some of the results obtained in the course of a special examination of these particular ores, conducted at the State School of Mines at Rapid City, So. Dak. Various circumstances have interrupted the work, and it will easily be seen that relatively little has yet been accomplished; but it is hoped that this little may be of sufficient interest to justify a later supplement. Tellurium, discovered by Muller von Reichenstein in 1781, is generally classed as a very rare metal; it is further mentioned by one of our late writers as " of comparatively little importance," and as obtained from its ores by a " complicated process.'' Concerning its rarity, we have some trustworthy evidence below. Its commercial importance, particularly in connection with electrical appliances, has been passed upon by Mr. Edison ; * and it is certain that, in some metallurgical processes for the treatment of gold- and silver-ores, it may be saved as a byproduct at a relatively reasonable expense. The importance of tellurium as a mineralizing agent is emphasized by the remarks of one of our leading metallurgists,jwho, in his own practice and by a wide series of experiments, has found its occurrence to be much more general than has been supposed. Recently the same writer has discussed the occurrence of tellurides and oxidized tellurium compounds in the gold-ores of Cripple Creek, Colo., and in those of the Black

Jan 1, 1897

By E. A. Farrell

A comprehensive survey is made of the status of the asbestos industry as it relates to marketing the product. Included are descriptions of the various types of asbestos and the grading and classification systems used. The uses of asbestos, distribution practices, and types of ore bodies are all related to marketing. World production, the producers and their capacities and world consumption for 1966-67 are summarized and statistical data are included. Asbestos is a general term describing a family of fibrous minerals of the serpentine and amphibole mineral groups. Asbestos has a long history going back to the time of the Egyptians, when it was used as a lamp wick. The commercial mining of asbestos started in Canada, Russia, and Africa in the 1800's, and the first asbestos products were made in Italy and Russia. The five main types of asbestos are: chrysotile, accounting for 95% of the total mined, amosite, crocido-lite, anthophyllite, and tremolite. Canada, Russia, and Africa are the major producers of asbestos. The commercial utility of asbestos was at first based on the heat resistance of the fibrous mineral in the form of packing, at the start of the industrial revolution. Its current utility is based more on its ability to reinforce binders such as portland cement, rubber, and plastics. Its inertness to the chemical nature of most binders is unique. Most important is its ability to maintain its reinforcing utility when the product is exposed to weather and soil conditions as in asbestos cement boards and pipe, and heat, pressure, and chemical exposure as in brake linings and gaskets and packings. The mineral asbestos is also unique because its fibrous form permits it to be spun and woven to cloth or formed into paper. Many asbestos applications are critical to national defense and at the present time, there are no satisfactory substitutes. Grading and Classification Canadian chrysotile asbestos fiber is graded and priced by length since basically the longer the fiber the higher the utility. The Canadian asbestos industry does not, however, classify the fiber by direct length measurement, but by a dry screening test. The method is called the Quebec Standard Screen (QS) test. One pound of fiber is mechanically shaken in four vertically stacked sieve boxes. The relative proportions remaining on the sieves defines the grade. The longer the fiber, the larger is the amount that stays on the top coarse screens and the less on the lower, finer mesh screens. Other tests can be used to further define the length distribution of fiber such as the wet screen Bauer McNett and the Suter Webb Comb (3 group only). The Canadian grading system divides the milled fibers into 5 main groups: group 3, 4, 5, 6, and 7, with 3 group being the longest, and 7 the shortest. Each group is further divided to subgrades, identified in each group by the letters A to Z, with "A" the longest and "Z" the shortest. See Appendix 1 for the Canadian QS classification system. The Russians also use the QS test on chrysotile. The Africans classify their chrysotile into grades similar to Canadian. The African crocidolite and amosite, however, are classified into actual length groups such as l to 2 in. and 2 to 3 in. Amosite and crocidolite are generally longer than chrysotile but also more brittle. Milled asbestos is not composed of staple length fibers like fiber glass or cotton, but of a mixture or blend of fibers ranging from long to short. Milled asbestos has a fiber length distribution similar to the particle size distribution of a powder. For example, the longest group 3 chrysotile grades have a high percentage of the longest fibers (1/2 to 3/4 in.) and low percentage of short fibers (0.003 in.). The figures in Table 1 give the approximate length distribution of the longest, middle, and shortest groups. A second and further method of classifying fiber is the degree to which the fiber bundles are separated to form a larger number of smaller diameter bundles. This property is normally described as the degree of fiberization, openness or surface area. Air permeability tests are used to measure surface area. Asbestos pro-

Jan 1, 1971

By Y. C. Liu, G. A. Alers

Using X-ray pole-figure information and the single-crystal elastic constants, the angular variation of an elastic modulus in a polycrystal can be calculated and compared to measured clalues. This procedure has been used in the past to provide supporting ecidence for a particular choice of ideal orientations in the description o the X-ray pole figure. Since it is well-known that the absolute value oj an elastic modlus oj a poly crystal cannot be acczrralely calculated from the single-crystal elastic constants, there exists a serious question about the reliability oj this modulus method in the study of textures. This paper deriz-es sez3eral simple fornzulae for the ntzgular lariatiion of Young's modulus in the plane o a rolled sheet sing the same ssuinptions which lead to the lack oj detinztion of the absolute c'alre OJ the elastic ,nodulus. The vesults show that, although the absolute isallre oj Young's modulus depends strongly on the assumptions made, the shape of the modulus vs angle curve is not very sensitive to the assumptions and thus can be used reliably in texture studies. Exatzples oj' using this criteriotz are illustrated in the text. NeARLY all poly crystalline materials have some preferred orientation in the arrangement of their grains and hence exhibit anisotropy in their properties. This preferred orientation is usually measured and studied by X-rays which yield detailed information on the statistical distribution of grain orientations in the form of pole figures. The usefulness of these pole figures in theories of texture formation and in predictions of properties has come to depend almost entirely on the characterization of the pole figure by one or more ideal orientations. Unfortunately, this characterization is not unique and different authors often present different ideal orientations to characterize a given pole figure. In order to distinguish between these different choices of ideal orientations, it is necessary to go beyond X-rays and consider other physical properties which reflect the texture' simply because any choice of ideal orientations must predict correctly the observed anisotropy in all physical properties. The most common example of this procedure has made use of the angular variation of Young's modulus with respect to the rolling direction in the plane of a rolled sheet.3 4 Here the anisotropy can be measured easily and it can also be calculated from the single-crystal elastic constants and the chosen ideal orientation. Unfortunately the methods used to calculate this anisotropy were chosen for their simplicity rather than for their mathematical rigor so that there exists a serious question as to the validity of conclusions reached by this modulus method. It is well-known5 that the absolute value of the Young's modulus of a polycrystalline aggregate cannot be calculated very accurately because different mathematical averages over the grains yield different results. It is one purpose of this paper to examine the effect of different averaging procedures on the calculated anisotropy of Young's modulus in the rolling plane of rolled sheets in order to see if this property can be used reliably in texture studies. This particular modulus and type of material were chosen because the modulus is easily measured and rolled sheet is technologically important. The results show that, although different averages yield different absolute values for Young's modulus, the shape of the modulus vs angle curve is not very sensitive to the averaging procedure and thus can be used as a criterion to check the various ideal orientations used to characterize the X-ray pole figure. Examples of this checking procedure are given in the final section. Another purpose of this paper is to examine the possibility of using the anisotropy of Young's modulus as an indicator of texture without reference to pole figures or ideal orientations. Such a use would require that different textures yield quite different shapes for the modulus vs angle curve so that the distinction between textures would be quite clear. The experimental results presented in the final section indicate that there is easily enough variation in shapes to allow modulus measurements to be useful texture indicators, par-

Jan 1, 1967

By M. E. Tyrrell, Alan H. Goode

The application of a simple, two-dimensional computer technique for evaluating rock burst potential in cut-and-fill stopes was investigated. The principal purpose of the study was to compare the effectiveness of high-modulus fill and destressing as aids in the control of rock bursts. Two conclusions that are probably of general applicability are drawn. First, high-modulus fill is ineffective as a means of increasing the mine stiffness and acts to control rock bursts only if it supports enough load to reduce substantially the stresses on the unmined vein material. Second, destressing is most effective if it is performed when the vein material is near the point of failure.

Jan 1, 1975

By R. M. Brick, Arthur Phillips

The Institute of Metals Division Lecture in 1936, given by R. F. Mehl, on diffusion in solid metals1, was introduced with the statement that "the phenomena of diffusion are intimately related to many basic problems of the metallic state, but in addition to this the process of diffusion is of first importance practically." In view of the scope of that lecture, it does not seem necessary to review the importance, history or present status of diffusion problems. One aspect of the subject of diffusion that has received little attention became of some immediate importance in the course of a study on segregation. When a solid solution alloy freezes, the familiar mechanism of solidification requires that the first nuclei formed be low in solute concentration, with a resultant normal segregation or coring effect during freezing. Theoretically, musion of solute atoms during solidification should result in a homogeneous solid solution. Actually, of course, it is impossible in most binary alloys to obtain a cooling rate that will permit diffusion to eliminate coring in the freezing dendrites. For a given alloy, the extent of diffusion attained up to the point of final solidification will determine the degree of enrichment in solute atoms of the final liquid phase. The flow of this liquid into dendritic contraction channels and the solute concentration of the liquid seem to be the determining factors as to whether the final gross segregation is normal, inverse or absent. The purpose of the present study of diffusion was to determine to some extent the separate diffusion rates of copper and magnesium into pure aluminum with a view to clarifying previous results on segregation in these alloys; i.e., the fact that under similar freezing conditions aluminum-copper alloys segregate inversely and aluminum-magnesium alloys segregate normally. Of concomitant interest were the questions of the homogenization times required for segregated ingots or partially melted, i.e., "burnt," structures, and the solution heat-treatment times required for cast, hardenable aluminum-copper and aluminum-magnesium alloys, for worked and annealed structures, and so forth.

Jan 1, 1937

By Pei-Yung Huang, C. R. Hayward

In order to understand more fully the actual state of copper lost in copper reverberatory slags, a systematic study on the various reactions between certain metallurgically important copper compounds and synthetic copper reverberatory slags was undertaken by the authors in the Massachusetts Institute of Technology from 1942 to 1945.1 This paper, being only a part of the work completed, is published first because it furnishes the first experimental evidence of the formation of copper ferrite from reactions between cuprous oxide and copper reverberatory slags. Choice of Slag Composition The choice of the composition of the synthetic reverberatory slags to be used was much deliberated. Commercial copper reverberatory slags, neglecting minor constituents, avcrage :2,3 45 to 47 pct FeO; 38 to 42 pct SiO2; 5 to 6 pct CaO; 5 to 6 pct A12O3. Since the ternary system CaO-FeO-SiO2 has been much more thoroughly studied4 and is much simpler than the quaternary system CaO-FeO-SiO2-Al2O3, it was decided to use calcium oxide only instead of calcium oxide and alumina in the synthesis of the slags. Fortunately the composition of the average copper reverberatory slag with calcium oxide substituted for alumina lies in the region of the phase diagram clarified by the investigators. A survey of the phase diagram (Fig I) suggested two compositions: (I) the composition near the invariant point S, which is made up of 46 pct ferrous oxide, 37 pct silica and 17 pct calcium oxide; (2) the composition near the invariant point K with 45.5 pct ferrous oxide, 43 pct silica and 11.5 pct calcium oxide. Composition S has the advantage that the percentages of ferrous oxide and of silica almost exactly coincide with those of the average reverberatory slags, and that of the lowest melting point (1093º ± 3ºC) in the whole ternary system. The calcium oxide content, however, obviously is high. Since we have already substituted calcium oxide for alumina, and since calcium oxide is more basic than alumina, the fulfil- slag is decidedly too basic. Composition K has a slightly higher melting point (1150O + 3OC) and a higher silica content, but this is preferred because the slag is saturated with respect to tri-dymite and thus should not corrode siliceous refractories. Besides, it is less basic than composition S. The filial slag composition, therefore, was chosen to

Jan 1, 1949

By T. L. Joseph

IT is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man's thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life's work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe's pioneer work in the field of metallurgy. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that under- lies the production of steel. Although Dr. Howe's work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book1 on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe's ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blast- furnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1946

By George B. Clark

THE " Munroe effect" of shaped explosive charges was discovered by Charles E. Munroe more than 50 years ago (in 1888), but it was not until World War II that it was put to any practical use. Both Allied and Axis armies used the principle effectively in bazooka projectiles, artillery projectiles and in fixed shaped charges. The first two were used primarily to combat tanks and other armor and the latter to assault pillboxes and other fixed concrete emplacements. Many engineers and others who saw the military application of the jet effect of shaped charges believed application would be possible in many industrial fields where blasting is used, such as mining and quarrying. Some work has already been done on the problem of making shaped charges applicable to mining operations. Experimentation conducted at the National Tunnel and Mines' was directed primarily along the lines of use of shaped charges for secondary blasting in connection with long-hole stoping methods. Experimentation initiated earlier and conducted by the author2 at the University of Utah on a more scientific basis was directed at revealing the basic principles of the functioning of shaped charges, as well as the feasibility of using them in mining operations after the principles of their operation had been clearly defined. It was found that: (I) a given design of charge required an optimum standoff to make it most effective, either in penetrating solid rock or steel (see Fig 3); (2) for a given design of charge there exists an optimum ratio of charge diameter to charge height above which the increase in effectiveness of the charge decreases rapidly (see Figs 4 and 5); (3) partial confinement has the effect of making charge performance much more consistent; (4) the higher power and higher velocity explosives tested are much more effective than relatively low-strength explosives; and (5) shaped charges may be adaptable to mining operations in secondary breakage and drilling blasting holes. Fig I is a diagrammatic sketch of the action of a shaped charge for two types of cavities, while Fig 2 shows the approximate manner in which the jets are believed to be formed when an explosive wave encounters the cavity, approaching it from the top. The experimentation already completed has laid the foundation for further research in the study of shaped charges. Standoff effects, effect of the strength of explosives and other features have been fairly well established. Such elements in the design of shaped charges as (I) geometry of cavity liners, (2) relative horizontal dimensions of explosive column, (3) effect of

Jan 1, 1947

By John A. Ames

Webster's dictionary nearly equates portland cement with its current primary definition of cement. While such equation may be a triumph of common usage, the confusion between the terms cement and concrete unfortunately is very widespread. Full definition of cement properly would extend to many substances, but for purposes of this chapter cement is restricted to "varieties" of portland cement including "portland-pozzolan" cement. Among the usually recited historical notes concerning cement is that it was developed by the Romans. Their use of cement in the great structures of Rome, and even in the far corners of their Empire, such as Hadrian's Wall in the north of England, testifies to the antiquity of a major cement industry. From English sources we know of John Smeaton's carefully proportioned hydraulic cement mixed in 1756 and of Joseph Aspdin's patented cement to which, in 1824, he gave the name portland cement. (He claimed that his cement mortar looked like the famous dimension limestone quarried from the Isle of Portland on England's south coast.) The year 1971 marked the centennial of portland cement manufacture in the United States. A fair historical account of the many real contributors to the cement industry between 1756 and 1972 unfortunately would be too extensive for this chapter. Development of rotary kiln practice and burning at higher temperatures clearly was the major move into today's technology. As part of the 4th edition of Industrial Minerals and Rocks, this chapter on utilization focuses on inferred interests of the anticipated readers. The main period for which statistics are cited generally is that since the 3rd edition (1960) of this same volume. Cement manufacture is the processing of selected and prepared mineral raw materials to produce the synthetic mineral mixture (clinker) that can be ground to a powder having the specified chemical composition and physical properties of cement. Cement making incorporates a number of distinct steps, but it is characterized by the key pyroprocessing (or "burning") step, which brings about the necessary changes in the raw materials. This pyro processing is a chemical process. Conversion of large volumes of mineral raw materials into specification-controlled cement at relatively low cost is the objective. Statistics on the cement industry are of uneven quality. The U.S. Bureau of Mines (USBM) is the principal collector of available data. These statistics can be only as good as the quality of information supplied by the reporting companies. The data perhaps most often questioned relate to productive capacity of the industry. The questions submitted by USBM are valid, nevertheless, and the information gained from them, as good as is available, is what is generally used. The Portland Cement Association also is a source of much quality information. The year 1972 witnessed a test of the adaptability of cement industry statistics. This was the year of conversion from barrels and sacks of cement as the units of measure to tons and hundredweights. The barrels and sacks related to volumetric measures in that a sack was judged to be 1 cu ft (weighing a "standard" 94 lb). A barrel was 4 sacks. Volumes of concrete are stated in cubic yards, and the number of cubic feet of cement in a cubic yard of concrete was a sensible approach to the mensuration involved. However, cements do not weigh the same amount from plant to plant or from type to type, and the buyer was more interested in getting an assured weight for his money than in "buying air." Thus, a sack, in accepted practice, became 94 lb instead of 1 cu ft, and a "barrel" became 376 lb, regard- less of whether it would fit into 4 cu ft of space. With the de facto dealing in weight rather than in volumes, the awkward numbers made little

Jan 1, 1975

By F. L. Wolf

The catenary system of line construction possesses so many desirable characteristics from the operating standpoint that it has wide application for all types of electric traction. Many steam roads are electrifying sections of their lines, and in most cases are operating both steam and electric locomotives over the same track. This means that the overhead catenary system is subjected to the severe corrosive action of locomotive smoke, and data concerning the resistance of various alloys to this form of corrosion are very desirable from every point of view. Reliable and specific information and data on the subject of corrosion due to steam and smoke from locomotives are extremely meager and, on this account, extensive service tests, together with accelerated tests, have been made on a number of commercial metals and alloys. The observations and data recorded in this paper are the result of a preliminary test which was started in 1923 and which has been carried on to the present time. The recognition of the need for even more detailed and accurate data has resulted in the undertaking of another test which has been in progress for about a year. The result of this test will be published in due course. Some years ago The Ohio Brass Co. was asked by one of the large steam railroad companies to furnish data on construction details for a catenary system which it was considering for one of its divisions. The selection of materials which would give the necessary physical characteristics as well as withstand the severe corrosive action of locomotive gases caused electrical railroad engineers considerable concern. At that time, there were available no specific or authentic data on these important questions: no systematic investigation of the problem appeared to have been made, even though it's importance was generally recognized. Such observations as had been made were crude in that they had been limited largely to visual inspection which too frequently is most misleading. However, the scattered information which was collected gave important clues as to how best to start an investigation. Technical literature was studied, metallurgical experts were consulted, and the problem was discussed with engineers who were in close contact

Jan 1, 1930

By Donald H. Yardley, A. Aly Selim

Abstract-An economic simulation model was developed to predict the amount of copper recovered from copper oxide deposits, and the cost of producing it as a function of the deposit parameters. The economic simulation model includes programs for fragmentation design and cost, copper extraction, solution distribution and recovery, effluent solution cutoff grade, and financial analysis. Cost and price indices were also developed to evaluate the economic feasibility of in situ leaching operations as a function of their starting date. Application of the models to various hypothetical properties having the same area and different ore thickness shows that the effluent solution cutoff grade does not vary with the ore thickness nor with its grade. The percent of copper recovery is, however, shown to increase with the increase in the ore thickness and is independent of the ore grade. It is also shown that while the profit per unit of extracted copper increases with the increase in ore grade or ore thickness, the rate of return on total investment does not show any correlation.

Jan 1, 1978