Search Documents

By A. G. McGregor

IN THE Southwest a number of large steel chimneys discharge the gases from the copper smelting furnaces. Some of these chimneys show no deterioration after twenty years, others show serious deterioration after tour years service. A steel stack 20 ft. 7 ½ in. (6.3 m.) in diameter by 279 ft. (85 m.) high, Fig. 1, used for roaster gases only at the Calumet & Arizona Mining Co.'s plant at Douglas, Ariz., was lined to the top of the bell, 40 ft. (12 m.) from the base, with common brick placed on end, lime and cement mortar being used. Above the bell, the stack was lined with 4 by 4 by 8 in. (10 by 10 by 20 cm.) building tile, placed on end, making a lining 4 in. thick. The tiles were supported on angle-iron rings, riveted to the inside of the chimney shell about 15 ft. apart. The chimney was put into use in the latter part of 1913. Four years later, considerable of the tile lining had fallen out of place and mixed with the flue dust at the bottom of the chimney. About a year later, several . flattened and distorted sheets were noticed about 70 ft. below the top. An investigation showed that the thickness of these distorted sheets, which was originally ¼ in., had been reduced one half. One year later, or six years after the chimney went into use, several holes, a square foot and smaller in area, appeared near the flat spots mentioned. Soon afterwards, when the chimney was shut down for repairs, it was found that most of the tile lining for 125 ft. from the top had fallen out and that the steel shell was badly corroded; but where the lining remained in place the shell was undamaged. Many of the tile which had fallen out of place had become soft or flaky and crumbling, others were as hard as when placed. An analysis of the hard and soft tile is shown on p. 2. These tile were of a fireclay mixture, and were used instead of common brick on account of lower cost. The steel forming the upper 125 ft. (38 m.) was replaced, and a 4 ¼ -in. (11-cm.) lining of firebrick was laid from the bell to the top of the chimney. The brick were placed on end, wedges and keys being used. After each 8-in. course was set, keyed, and wedged tight, thin mortar -water, sodium silicate, and finely ground silica-was worked into the joints. The brick are supported on angle-iron rings, every 15 ft., in the same way as the tile.

Jan 1, 1921

By H. L. Luo, P. Duwez, C. C. Chao

BY rapidly cooling alloys from the liquid state, it is possible to obtain solid solutions beyond the equilibrium concentrations, provided that the components are miscible in the liquid state. Typical such cases include CU-Ag,1 Pt-Ag,2 CU-Rh,3 nickel-base alloys with silicon, germanium, and tin,4 and cobalt-base alloys with silicon, germanium, tin, aluminum, and gallium.5 In the present note it is shown that terminal solid solutions can be appreciably extended in A1-Mg alloys. The alloys whose compositions are given in Table I were prepared by induction melting in tantalum crucibles under an argon atmosphere. Both aluminum and magnesium were 99.99 pct pure. Weight losses after melting were less than 0.2 pct for the aluminum-rich alloys and less than 0.4 pct for the magnesium-rich alloys. From these weight losses it was estimated that the compositions of the ingots after melting were accurate within 0.3 at. pct for aluminum-rich alloys and within 0.5 at. pct for magnesium-rich alloys. As indicated in Table I, the compound AuCd10 in which there is an ionic contribution to the bonding. The authors thank Dr. J. H. Westbrook of the Research Laboratory, General Electric Co., for arranging the supply of materials and for his interest. This investigation was supported by the U.S. Atomic Energy Commission under Contract AT(30-1)-1002, Scope I. some of the alloys were also chemically analyzed and the results confirmed the limits of uncertainty based on weight losses. Rapid quenching from the liquid state was achieved by techniques previously described.8,7 The principle of these techniques consists of propelling a small globule of liquid alloy (about 20 mg) onto a copper substrate. The thin foils easily detached from the copper substrate were analyzed by X-ray diffraction using a Debye-Scherrer camera 114.6 mm in diameter and either nickel-filtered copper Ka or iron-filtered cobalt Ka radiation. Since the back-reflection doublets were resolved, the wavelengths used in the computatioas were CuKal = 1.54050A and CoKa1= 1.78892A. Lattice parameters were obtained by extrapolation of the Nelson-Riley function, and the tables compiled

Jan 1, 1964

By Henry E. Colton

NeaR the town of Christiansburg, Va., occurs a singular feature in topographical as well as geological structure, which may be said to have an important bearing on a large area to the southwest. The great water-shed ridge, which divides the waters flowing into the St. Lawrence from those flowing into the Atlantic ocean, coming southwestward, forms all of what was the boundary of Maine as agreed upon by the treaty of 1783, and a part of the present boundary, all of the northern New Hampshire boundary, and entering Vermont, continues south of Lake George. Passing irregularly through New York, it enters Pennsylvania, and there bifurcating, sends one prong to the west as a divide between the waters of the lakes and the Ohio, while the other becomes the steady, regular ridge which gave it the name of Alleghany, and thus passes on southwestward through Virginia. At no point has it ever been the geological divide. Its course, commencing in the Archean rocks, has passed through nearly every series of formation, and comes into Virginia in the Carboniferous strata. The geological divide—the line between the fossiliferous and the non-fossiliferous rocks—lies, in Canada, to the west of it, but from New York south into Virginia is far to the east. Reference to Dr. Hitchcock'k map will show this. But at the locality noted these positions are changed; the water-divide becomes the eastern chain, and the geological divide is the western, returning, it may be said, to the positions occupied in the region where they originated. These relations are shown on the large map accompanying the present paper. For several miles, the track of the Norfolk and Western Railroad

Jan 1, 1888

By W. E. Keck

THE potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-phorous ores. Research on the flotation of each of these classes of ore was carried out in the following Planner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly, pure state. There are two varieties of the mineral-specular hematite and massive hematite. The latter is the principal variety, but the former is an Impor-tant mineral of iron in some of the potential ores. Because of this condi-tion, flotation research was performed with both varieties. This research consisted essentially of: (1) a survey of the literature on hematite flota-tion, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the; development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a pro-prietary frother and oleic acid or other soluble oils 2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1937

By Harry M. Mikami

Chromite is the only ore mineral of metallic chromium and chromium compounds and chemicals. Because of this fact, chromite and chrome ore are used synonymously in trade literature. In commercial market quotations, chrome ore is the term commonly used. Chromite per se, because of properties imparted by its chromium content, is used in refractories and in special purpose moulding sands for metal casting. There are many other minerals containing some, generally minor, amounts of chromium, but none are commercial sources of the element (Thayer, 1956, p. 15). Chromium and chromite have many diverse uses that, directly and indirectly, critically affect vast segments of our modern industrial system. Most important are probably the metallurgical applications wherein chromium is a component of heat, abrasion, corrosion, and oxidation-resistant, and high strength alloys of many types. Stainless steels are the largest volume category of chrome-bearing alloys. Chromium chemicals are used in leather tanning, in pigments, dyes and mordants, printing, :hemica1 process industries, photography, pharmaceuticals, metal plating, pure chromium metal production, and for many other purposes. Chromite is a necessary constituent in basic refractories indispensable for the production of steel, copper, cement, and glass. Under present economic-political conditions, he U.S. and for that matter, North America, has virtually insignificant ore reserves of chromite. There are chromite deposits, as will be described, but they would only be used under highly abnormal conditions if all outside sources were cut off. All chromite used in the U.S. is imported from the eastern hemisphere in which are contained the principal world reserves. As the main suppliers in 1971-72 were the USSR, Turkey, Republic of South Africa, Philippines, and Rhodesia, the strategic nature of chromite is obvious.

Jan 1, 1975

By F. C. Stanford

The work of an engineer is to direct natural forces so that the: bring about the results that he wishes to secure. Heretofore he ha concerned himself chiefly with physical forces and inanimate objects until he has secured a truly marvelous degree of control over them The great problem of the present age is to secure a like degree of know1 edge and control of the human factor. Progress has already been made along this line, but it is only a beginning. Wilhelm Ostwald says tha scientific knowledge enables a man to be a true prophet; but it must be remembered that a good many people do not seem to be able to main tain a high average in prophecy. In short, 'the average of knowledge is not equal to the average needs of the present time, but continually fails to keep pace with it. It has been aptly said that the really essentia need of the period is for more brains; if we only had sufficient knowledg and sagacity we could not only solve all difficulties, but prevent then from arising. This generalization holds good for an industrial organization. Th most vital need of the management is for more brains. The logica course for an engineer in charge of an industrial organization is, therefore to direct whatever forces may be at his command toward the development training, and guiding of all the brains in his organization. This is easie said than done, for it involves the carrying on toward two objective: the maximum of productive work, and the development of the individual who perform it. This is essentially like the rebuilding and enlarging of plant, keeping it in full operation the while. On the other hand, if th aim is merely for maximum production from an organization, withou offering opportunity for development, the final outcome will necessari be like that of a plant that is driven at full capacity without stoppin for repairs or improvements; it eventually becomes so run down th either a complete rebuilding is necessary or else it has to be abandone

Jan 1, 1918

By George Rice

THE A.I.M.E. Ground Movement and Subsidence Committee, pro-posed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bitu-minous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Pitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O'Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various Winds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1939

By Ian William Wark, Alwyn Birchmore Cox

In defending the chemical theory of flotation, Taggart, del Giudice and Ziehl have criticized1 the views of those who prefer to attribute the effects of certain flotation agents to adsorption. Perhaps with some justification, they describe the latter term as the "haven of refuge of writers lost in a morass of shaky experiment and muddy thinking." We prefer to regard it, however, as a haven of refuge for writers who seek a conventional term to describe the formation of films of flotation reagents on solid surfaces, because in many cases it is not yet possible to specify the forces that hold them there. Originally, as Taggart and his associates state, adsorption connoted a concentration difference and nothing more. In recent years, workers in the field of surface chemistry have tacitly added other meanings, and they now speak of orientated adsorption of unimolecular films on a solid sub-strate, of chemi-adsorption, and of exchange adsorption. Thus the term adsorption may connote simply the Gibbs layer of excess concentration at the surface of a solution, or a unimolecular film at the surface of a solid. Perhaps this has led to the misunderstanding of Taggart, del Giudice and Ziehl concerning the relationship between surface tension and adsorption at solid surfaces. The change in "surface tension" accompanying adsorption at a liquid surface can be used as a measure of the adsorption, and the Gibbs equation as quoted by these authors correlates these two conceptions. But, to correlate two conceptions docs not necessarily imply an attempt to explain either, although sometimes such an "explanation" is carelessly inferred. Use of "surface energy per unit area" instead of the numerically equal but more difficult and less definite conception of "surface tension per unit length " would lessen many of the present difficulties. (Compare with Adam.2) At interfaces involving a solid phase, neither '" surface tension " nor " interfacial tension "can have any meaning, but the conception "interfacial energy per unit area" call be understood by anyone who is familiar with the concept of free energy. While it is true that surface energy cannot be directly measured at a solid surface,

Jan 1, 1939

Unlike the bituminous part of the coal industry, the production of anthracite has been fairly well publicized; in fact until about 1845 whenever the coal industry of Pennsylvania was mentioned in papers, magazines or books, anthracite only was meant. Beginning with shipments by river in 1820 fairly complete records of shipments were published each year, and as this variety of coal was the only one used for domestic purposes east of the mountains and north of the Potomac, there was considerable interest in the producing fields on the part of the public. Transportation of anthracite was the cause of the building of the early canals in the state, and later, of some of the earliest railroads. In most publications it has been assumed that commencement of shipments in 1820 was the beginning of the industry; this is far from being so, and it is with the earlier developments this chapter will deal, leaving the later and better known records to existing publications. (See Table No. 53.) The first reference to coal in Pennsylvania by Gabriel Thomas in 1698 has already been mentioned,1 it could only have been anthracite in that section; although of course, he never saw any coal there. Little coal was used excepting by smiths for many years after that. In 1728 the Coventry Forge paid the expenses of a man "to town for Sea Coall and Steell for ye hammer;”2 in 1729 New Castle coal was sold in Philadelphia;3 in 1740 an advertisement mentioned, "very good Pitt and Sea Coal at 18 pence a bushel; at which price 'tis allowed to be cheaper Fewel for Hearth Fireing than Wood at the present Rates,"4 a view not shared by most of the people there for about eighty years; in 1752 Newcastle coal was again mentioned.5 There are no references to coal in the writings of any of the Moravian missionaries, although some who settled near Mauch Chunk in 1746 said that the Indians there made their pipe heads of a soft black stone, which was much more apt to have been slate than anthracite." Several stream

Jan 1, 1942

By A. E. Moss, J. K. Gustafson

MEASURED in terms of ore tonnage, the New Quebec and Labrador iron ore fields promise to rank with the greatest iron ore districts of the world. Over 400 million tons of high-grade ore for direct shipping have been discovered to date. Much greater amounts of lower-grade beneficiating ores are indicated by outcrops. Many hundreds of square miles of iron formation await testing. By 1954 iron ore will begin to move towards American blast furnaces, and shortly thereafter the annual rate of production is expected to reach 10 . million tons. To bring this vast project into being over $200,000,000 will have been spent for exploration and development, mining equipment, hydro plants, townsites, the building and the equipping of . a 360-mile railroad, and the construction of docks and ore-handling facilities. The most important iron ore deposits are located over 300 miles from tide water, see frontispiece and also Fig. 1. The frontispiece shows principal sources of iron ores and manganiferous iron ores for the U. S. and Canadian steel industry, and the major smelting districts are shaded on the map. No navi- gable rivers lead into the interior. When work was . commenced on this project there were no roads, no railroads, no communication ,system, no inhabitants, and no adequate maps either topographical or geological. The geological field season was limited to approximately 100 days per season. The obstacles facing this enterprise were many and varied. Its success will be due to the integrated team work of people of diverse skills. Explorers, Indian guides, prospectors, geologists, surveyors, mechanical, civil, electrical, and mining engineers,

Jan 1, 1954

By Thomas Read

PERSONNEL work is a term recently introduced to cover the great variety of activities in industrial work that deal with the human factor. Much attention has been focussed upon individual phases of personnel work, such as accident prevention, sanitation, "welfare" work, reducing labor' turnover, and so on. In most cases these activities have been carried on as though they were distinct and separate fields; as a matter of fact, they are only different phases of the single problem of human engineering, and each has important and fundamental relations with the others. Thus, for example, high labor turnover is one of the most .important causes of a high accident rate, and unsatisfactory housing conditions are an important cause of labor turnover. In the early stages of the study of these problems, it was necessary to take them up separately; the time has now arrived at which it is desirable to consider them as a whole in order to bring them into the right relation to each other. When thus considered as phases of an interrelated whole, they may be grouped as personnel work. A discussion of the importance of personnel work as a means of in creasing dividends in industry may be objected to by some as a too materialistic way of looking upon work that is humanitarian. Nothing could he more mistaken than such an opinion. Humanitarianism, per se, has no place in industry, and nothing is gained and much is lost in pre tending that it has. The only reason why a corporation engages in business is to make profits, and any activity of the corporation that does not tend either directly or indirectly toward that end is poor business. It is equally poor business to overlook any activities that do tend indirectly to the making of profits. On this basis, personnel work can be justified as a corporate activity; there is no justification whatever for abstract humanitarianism from the business standpoint. One characteristic of the American workman is a general high level of intelligence, and it is an insult to intelligence to ask a man to believe that anything so impersonal as a corporation is really desirous of benefiting

Jan 10, 1917

By Cyril Smith

A COMPLETE discussion of the literature on the subject of the influence of copper on iron and steel will be published elsewhere.1 The present paper is concerned especially with the precipitation-hardening of copper steels, and brief mention will be made here only of the work of Kin-near,2,3 Nehl4 and Buchholtz and Koster,5 who alone have studied this phase of the subject. Kinnear found that normalized low-carbon steel castings containing about 1.0 per cent copper on drawing at temperatures in the neighbor-hood of 530° C. (1000° F.) increased in tensile strength and yield point, with little decrease in ductility. The maximum effect was obtained with about 0.9 to 1.0 per cent copper, and when the copper exceeded 3 per. cent no improvement occurred on reheating. Kinnear did not study the effect of time of reheating-an all important factor where precipitation is concerned. Nehl,6 who apparently was unaware of Kinnear's work, recognized the change as due to precipitation and studied the interdependence of time and temperature of reheating, the temperature of the initial solution heat treatment, and the speed of cooling necessary to retain the bulk of the copper in supersaturated solu-tion and to give an increase in hardness and tensile strength on reheating. Nehl found that if the final rolling or forging temperatures exceeded 700° C. (1300° F.) it was not necessary even to normalize the steel, but full precipitation occurred on merely reheating the forged or rolled shapes at 500° C. (930° F.).

Jan 1, 1933

By P. J. Shenon, J. C. Reed

The Elk City district is in north-central Idaho about 60 miles east of Grangeville and near the headwaters of the South Fork of the Clearwater River (Fig. 1). At the height of its boom in the early sixties, Elk City had a population of more than 2000 people, Published estimates of the placer production from the district range from $10,000,000 to $18,500,000. Although the first quartz-vein location was made as early as 1870, very little gold was extracted from quartz ores until after the completion of the American Eagle mill in 1902. Between 1902 and 1932 a total of from $750,000 to $1,000,000 was taken from about six properties. General Geology Distribution of Rocks Banded gneiss (Fig. 2) is the most aburldant bedrock in the Elk City district. It is interbedded with schist and quartzite and ill some places these rocks have been intruded by sills and dikes. Banded gneiss prevails in the western part of the area whereas schist prevails to the southeast. Augen gneiss occurs for the most part as irregular bodies, which lie transverse to the trend of the banded gneiss and schist. It is largely confined to two areas; one of which extends from east of the American Eagle mine westward as far as the Black Pine mine, a total distance of about five miles, and another area of about two square miles in the vicinity of the California-Idaho placer mine. Quartzite is fairly abundant. In addition to the bands of the latter interbedded with gneiss and schist, some large lenses crop out in the southeastern part of the dik-trict near the southern contact of the area underlain by granodiorite. Granodiorite crops out over a large area and extends northeastward

Jan 1, 1935

By Charles E. Weaver

During the past few years there has been considerable activity in prospecting for oil and gas in several parts of western washington. From time to time seepages of oil or emanations of gas have been reported from various places. Several companies have been organized for the purpose of drilling, but only a part of these have actually begun operations. In certain localities very small seepages of oil occur, but up to the present time no oil or gas in commercial quantities has been obtained. In order to determine the conditions which may be favorable or unfavorable to the occurrence of petroleum it becomes necessary to know the character and extent of the geological formations in which such deposits might occur. In other regions where producing wells have been developed it is possible to know what formations contain the oil and what structural conditions influence its concentration in reservoirs or zones. It is usually possible to determine those strata which contained the materials from which the petroleum may have been derived and also the position and distribution of the more porous sandstone belts into which it may have collected. Detailed stratigraphic surveys may even determine the depth at which a certain known oil-bearing zone may be tapped at any particular place. It is also possible to recognize those formations which are presumably barren of oil, as well as those which are absolutely so. In new regions far distant from any of those which are now producing or have produced in the past, it becomes absolutely impossible to foretell whether oil may exist in commercial quantities or not. Assuming that such deposits do exist, it is extremely difficult to predict at what depth the produciqg zone or zones occur. However, in prospecting in a new and unexplored region, use should be made of such laws as have been found to govern the occurrence of petroleum deposits in other well-developed fields. Such deposits in their world-wide distribution are found almost exclusively associated with sedimentary rocks. Areas composed predominatingly of igneous and metamorphosed rocks are to be rcgarded as extremely unfavorable localities for the occurrence of commercial deposits of oil or gas. Assuming that such oil deposits are

Jan 1, 1916

By Dorsey A. Lyon, Robert M. Keeney

The utilization of hydro-electriic power in electro-metallurgical industries, aside from purely mechanical operations, may be of two kinds. The electric energy may be used to supply the heat necessary for the performance of the chemical reactions of a metallurgical process, or the electrolytic action of a direct current may be employed for extraction of metals, either in a reduction process or a refining process. In discussing this subject, it is well to distinguish between established industries, which are producing metals and alloys at a, profit by use of the electric current, and the many processes which are either still in the experimental stage or have not even passed the paper stage of development of a patent. That is, we consider electro-metallurgical industries as commercial operations which are now consuming large blocks of electric energy, while processes which are not in commercial operation are only prospective consumers. Also, owing to the difliculty and risk of any attempt to foresee the effect of the European war upon electro-metallurgical industries, we have felt obliged to disregard the war entirely, and state our opinions regardless of its existence. Application of Electric Energy to Metallurgy Disregarding electrolytic refining processes, the applications of electric energy to metallurgy, when considered from a commercial viewpoint, may be classified as follows: Industries Experimental Processes Manufacture of aluminum Electric-furnace smelting of: Electric-furnace manufacture of: Ferro-alloys Copper ore Pig iron Zinc ore Steel In this paper only the above industries and experimental processes will be considered as possible consumers of hydro-electric power in large quan-

Jan 1, 1916

By H. W. Hitzrot

THE new 4800-ton fine-grinding plant at the Hollinger Consolidated Gold Mines property at Timmins, in the Porcupine district of northern Ontario, went into operation in November 1937, and represents the culmination of an experimental program. The plant is a moderately low rectangular building of hollow tile on a steel frame, large enough to house four 7 by 15-ft. ball mills, with a 12 by 27-ft. classifier beside each mill. At one end is space for the addition of another mill and classifier or a mill and classifier for the regrinding of table concentrates. This regrinding is now done in the old grinding department of the main mill building. Also within the new building are the four 6-in. sand pumps for lifting the product from the low-dis- charge ball mills up to the classifier feed launders and the containers and appurtenances of a complete dust-collecting system. Together with the usual overhead crane, these constitute the major units of equipment within the new plant. The location is at the lower end of the main mill buildings toward the old tailings pond, now so neatly leveled off and sodded to rival the very best of our own W.P.A. projects. Close by the new grinding plant is a large dome-shaped structure-the new fine-ore bin designed arid built by Mr. Longmore and the Hollinger milling and engineering staffs. There are four separate automatically loaded inclined belt conveyors leading up from the bottom of the bin to the grinding plant. Each belt is equipped with a recording weightometer, in the grinding building. The whole structure and the machinery within it give the impression of permanence and a carefully integrated design with close attention to details, giving the operators every advantage for consistently good work. The many ideas and opinions behind this achievement were all ably organized and executed by the Hollinger milling and engineering staffs, anti not a few were directly initiated by them. Excellent cooperation was afforded by the Hollinger staff to the engineers helping to conduct the grinding and classification test program. It was the author's privilege

Jan 1, 1939

By Walter W. Bradley

(Three, papers included, in this discussion are classified as Mining Geology and also as one of the following-A, Metal Mining: B, Milling and Concentration: L, Geophysics. These papers are TP 2255, TP 2092 and TP 2038.) CONTENTS [PAGE Review of Fluorescence as Applied to Minerals, with Special Reference to Scheelite. (TP 1967 by J. W. VANDERWILT, Min. Tech., March 1946. Discussion by WALTER W. BRADLEY) I Geologic Interpretation of Magnetic Exploration on the Mesabi Range, Minnesota. (TP 2038 by R. B. H. JONES, Min. Tech., July 1946. Discussion by ROBERT B. SOSMAN) I A Technique for Photographing Difficult Subjects through a Petrographic Microscope. (TP 2092 by DONALD W. SCOTT, Min. Tech., Nov. 1946. Discussion by HORACE WINCHELL) 2 The Search for Concealed Deposits-a Reorientation of Philosophy. (TP 2146 by SAMUEL G. LASKY, Min. Tech., May 1947. Discussion by T. M. BRODERICK)3 Occurrence of Lead-zinc Ore at Iron King Mine, Prescott, Arizona. (TP 21 go by H. F. MILLS, Min. Tech., July 1947. Discussion by HUGH M. ROBERTS)3 Geologic Relations and New Ore Bodies of the Republic District, Washington. (TP 2197 by LAWRENCE B. WRIGHT, Min. Tech., July 1947. Discussion by AUGUSTUS LOCKE and J. A. RICHARDSON) 4 San Manuel Prospect. (TP 2255 by H. J. STEELE and G. R. RUBLY, Min. Tech., Sept. 1947. Discussion by L. KENNETH WILSON, ELDRED D. WILSON and the author) 5] Review of Fluorescence as Applied to Minerals, with Special Reference to Scheelite WALTER W. BRADLEY*-AS I recall, the first portable units for ultra-violet light of practical use with scheelite were developed at the Nevada-Massachusetts Tungsten Mine at Mill City, Nevada, and were used underground. Ultra-violet lamps are also installed there in the mill, above the gravity-concentration tables, for control observations. Geologic Interpretation of Magnetic Exploration on the Mesabi Range, Minnesota ROBERT B. SOSMAN*-When artificial precipitated magnetite is oxidized at a temperature in the vicinity of 100°C, the oxide is converted into a chocolate brown ferric oxide of the formula Fe2O3, free from ferrous iron, yet possessing the same magnetic susceptibility as the original Fe3O4. This form of Fe2O3 is variously called "ferromagnetic ferric oxide," " maghemite," or "gamma ferric oxide," and has been found as a natural mineral. If a body of magnetite in the Biwabik were to oxidize to this form, the oxidized and leached ore body might successfully conceal itself from Mr. Jones' survey by this ferromagnetic pretense. So far, gamma ferric oxide has not been found on the Minnesota iron ranges. I thought I had found some in the Hibbing pit in 1940, in a strongly magnetic specimen of soft ore differing in color from the prevailing hematite

Jan 1, 1947

By J. T. Eash, E. M. Wise

Platinum and palladium are the most generally useful, most ductile and least rare members of the platinum family. They have many important applications in the pure state but for other applications it is frequently desirable to harden them and otherwise modify their properties by alloying small amounts of the other platinum group metals with them. These alloys are frequently required to withstand very drastic forming operations and to possess certain mechanical properties to fulfill specific requirements. For these reasons a knowledge of the tensile properties and annealing characteristics of pure platinum and palladium as well as their more useful commercial alloys is important to the user and the fabricator. The present work was undertaken to fill this need. Rather brief (5 min.) annealing treatments were employed to render the data of maximum practical value and all tests were conducted upon 0.050-in. dia. wire, initially reduced 50 per cent in area by cold drawing, for the same reason. Conclusions 1. Pure (thermocouple grade) platinum reduced 50 per. cent by cold drawing exhibits the following tensile properties: ultimate tensile strength, 36,000 lb. per sq. in.; proportional limit, 27,000 lb. per sq. in.; elongation, 2.5 per cent in 2 in.; reduction in area, 95 per cent. When fully annealed by treatment at 1100°C. its properties are: ultimate tensile strength, 20,700 lb. per sq. in.; elongation, 30 per cent in 2 in.; reduction in area, 93 per cent. 2. The addition of alloying elements in moderate amounts markedly increases the strength and annealing temperature without much detriment to the ductility. The behavior and properties of variously hardened platinum alloys are considered in some detail. The behavior of a 20 per cent iridium

Jan 1, 1935

By R. J. Piros, Brusenback, D. A. Dahlstrom

DEWATERING fine coal has been a serious problem to many operators who desired to wet-wash finer sizes and maintain high recovery. Centrifugal driers have become popular for this purpose for sizes between 3/8 in. and 14 mesh. Below 14 mesh the perforated screen centrifuges lose a large per- cent in the effluent solid bowl types that do retain -14 mesh coal, produce excessive degradation, tend to retain the highest ash fraction in any size fraction, and are subject to abrasion, which results in higher maintenance. In 1949 Truax-Traer Coal Co. planned a cyclone installation at their Ceredo preparation plant to recover coal down to 150 mesh with approximately a 14-mesh top size. Since available centrifugal equipment was not considered satisfactory, an investigation of rotary vacuum filters was begun in cooperation with the Peterson Filters and Engineering Co. to determine the suitability of the Peterson Top Feed Reservoir (TFR) filter. This investigation, which is described below, has resulted in a highly satisfactory installation of two 6x10-in. Peterson TFR filters that have been in operation over a year. After some preliminary laboratory batch vacuum filter tests, a pilot plant double-drum Peterson TFR filter was installed at Ceredo to prove the feasibility of vacuum filtration and determine optimum conditions. The full scale units were then installed on the basis of the pilot plant results. This was followed by an extensive research program on vacuum filtration in the laboratory at Northwestern University to investigate basic design and operating variables and their influence on final moisture con- tent of the filter cake. A method of scale-up from laboratory batch tests to the full-size unit was also proposed and proved. Because of the importance of dewatering fine coal today, it was felt that the results of the three steps should be made available for the use of others facing this problem. The work at Northwestern is given in a theoretical section following the discussion of the pilot plant and full- scale operation. Fig. 1 is a flow diagram of the cyclone and filter installation. The feed is drawn from below the

Jan 1, 1952

By W. B. Daly, A. S. Richardson

The application of artificial refrigeration, or air-conditioning, to the ventilation of deep, hot mines has long been a subject of interest to the operators of such properties. Artificial cooling of the air in theaters, railroad coaches, and various industrial plants has been so successful within recent years that it has been natural to assume that the adoption of similar methods would afford a ready solution to the difficult problem of mine ventilation. It should however, be obvious, that although there may be nothing technically impossible in the application of this process to mine ventilation there is a great economic distinction between the maintenance of a high standard of comfort for a large number of people in a relatively small space such as a theater and the cooling of air to improve working conditions for miners scattered throughout the extensive workings of a large mine. Many methods of air-conditioning have been considered by the management of the Anaconda Copper Mining Co. at various times, but until the development of the process to be described in this paper none has seemed economically practicable. The Ventilating Problem at Butte The main obstacle to satisfactory ventilation in the Butte mines is the normally high temperature of the granite country rock. In the present operating zone, rock temperatures as high as 120' F. have been noted, and in some parts of the district the rate of increase of temperature with depth has ranged as high as 3.5" F. per 100 ft. Other factors, such as the decay of mine timber and the oxidation of sulfide minerals in the ore bodies, contribute to raise the temperature of the air in the working places but, particularly in the development of the mines to greater depth, the naturally high temperature of the rock is of predominant importance. In few other places, probably, are the ordinary ventilating measures more hindered than at Butte. At an operating depth now exceeding 3000 ft., all of the air required for ventilation must pass through timbered shafts which, because of heavy ground, are of small size and offer great resistance to the flow of air. Shaft compartments are rarely more than 4.5 X 5 ft., and the shaft area open to the flow of air usually does not exceed 65 sq. ft.; in only two shafts is the area as great as 85 sq. feet.

Jan 1, 1934