Search Documents

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By C. E. Shoenfelt

Wildcat drilling in the Rocky Mountain region did not suffer as large a decline in 1942 as was anticipated. The drilling program laid out by the Government at the beginning of the year stressed wild-catting operations and called for reduction of drilling in proved fields. The increased wildcatting campaign did not yield a great many new discoveries, nor important extensions to old fields. Several interesting wildcat wells were drilled in Colorado in 1942 but no new fields were discovered. The Wilson Creek field was extended and about 400 acres added to its reserves. In Montana two new oil fields and two small gas fields were discovered. The developments in the marketing situation had improved, however, making the prospects especially bright for 1943, as will be shown presently in the section on Montana in this report. In New Mexico eight wells were completed, which constituted discoveries ol either oil or gas but none of these was of major proportions. In Wyoming one new oil field and one new gas field were discovered, and one old oil field and one old gas field were extended. Most important was the disco-very of prolific oil producers in deeper sands in three old oil fields, of which one at least, Elk Basin, probably is of major proportions. Government Action On Dec. 26, 1942, President Roosevelt signed the O'Mahoney bill, calling for a flat 12.5 per cent royalty on lands in the public domain. It is expected that the enactment of this bill will encourage wildcatting in the public land states. Opportunity for a full discussion of the problems of reserves and production was afforded at the hearings conducted on the O'Mahoney bill by the minerals subcommittee of the Senate Committee on Public Lands and the statements submitted at these hearings last fall placed the situation, its causes and the logical remedy, clearly on record. It was established at the hearings that for several years the volume of oil discovered per wildcat well drilled has steadily declined; new fields discovered have not been of major proportions; drilling costs have advanced rapidly; a sharp decline in exploratory drilling took place in 1942, while the proportion of dry holes increased; the inescapable conclusion is that to find new reserves the search for oil must be intensified and much more wildcat drilling ' must be done. To ensure an adequate drilling campaign, the Petroleum Industry War Council, the Interstate Compact Commission and other representative oil organizations have voiced by resolution their opinion that an upward revision of crude prices is necessary to provide an incentive to the prospector to undertake the hazards of wildcat drilling, since statistics prove that only ope in five or six wells drilled results in actual production. Former Price Administrator Henderson rejected the recommendations for price increases and declared himself unalterably opposed to a general price advance, On the ground that such advances would contribute to inflation. Now that Mr. Hender-

Jan 1, 1943

By David B. Reger

Wildcat drilling for new supplies of gas and the expansion of previously discovered oil and gas pools were the principal petroleum activities in West Virginia .during 1942. Much of the new gas exploration is still uncompleted and still indecisive but various wildcats made substantial extensions to existing pools. Out of 53 wildcats drilled 27 resulted in commercial gas and 6 in commercial oil. Four of the oil discoveries also had commercial gas. No strictly new pools of oil or gas can safely be described as discovered but several scattered oil and gas wells previously drilled have been confirmed as the openers of definite pools; also, various completions closed wide gaps between apparent gas pools already discovered. The proved oil territory of the state was increased about 4850 acres and the proved gas territory about 51,000 acres. The new proved oil reserves should about balance withdrawals and the new gas may represent a substantial increase. Aside from the drilling in four rather lively pools, oil activity was slight because of unfavorable operating conditions and prices. Gas drilling also declined for reasons beyond the control of the operators. The account of operations, as gathered from trade journals and other reporting services, shows that 797 new wells were drilled, providing 119 new oil wells with 2762 bbl. of daily new production; 536 new gas wells with 1,228,501,000 CU. ft. of daily open flow: and 142 dry holes. Also... 76 old wells were drilled to deeper sands, with 71 bbl. and 26,034,000 cu, ft. of added production. On the new wells the oil average was 23.21 bbl. per well per day; and the gas average was 2,270,406 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 17.82 per cent. On deeper drilling the ratio of failures was 21.05 per cent. Production of oil for the year was estimated by the Oil ad Gas Journal as 3,492,000 bbl., as compared with 3,378,000 bbl. in 1941. Production of natural gas for the year is estimated by the author as 220,000,000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 207,000,000,000 cu. ft.* in 1941. General State op Industry Leasing of wildcat acreage increased considerably. The total land of all classes under lease may now exceed 5,000,000 acres. Taking into consideration completions, abandonments and corrected figures or estimates, Table I shows cumulative and late annual statistics. New Pools and Extensions Table 2 shows the principal areas of drilling activity during 1942. Various consolidations of territory, hitherto treated as separate pools, have been made. in addition to these active pools, extensive drilling was done in numerous other areas where pool boundaries can hardly be defined. Summary or Exploration Table 3 gives a summary of important wildcat or exploratory wells drilled during

Jan 1, 1943

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By C. E. Shoenfelt

Wildcat drilling in the Rocky Mountain region did not suffer as large a decline in 1942 as was anticipated. The drilling program laid out by the Government at the beginning of the year stressed wild-catting operations and called for reduction of drilling in proved fields. The increased wildcatting campaign did not yield a great many new discoveries, nor important extensions to old fields. Several interesting wildcat wells were drilled in Colorado in 1942 but no new fields were discovered. The Wilson Creek field was extended and about 400 acres added to its reserves. In Montana two new oil fields and two small gas fields were discovered. The developments in the marketing situation had improved, however, making the prospects especially bright for 1943, as will be shown presently in the section on Montana in this report. In New Mexico eight wells were completed, which constituted discoveries ol either oil or gas but none of these was of major proportions. In Wyoming one new oil field and one new gas field were discovered, and one old oil field and one old gas field were extended. Most important was the disco-very of prolific oil producers in deeper sands in three old oil fields, of which one at least, Elk Basin, probably is of major proportions. Government Action On Dec. 26, 1942, President Roosevelt signed the O'Mahoney bill, calling for a flat 12.5 per cent royalty on lands in the public domain. It is expected that the enactment of this bill will encourage wildcatting in the public land states. Opportunity for a full discussion of the problems of reserves and production was afforded at the hearings conducted on the O'Mahoney bill by the minerals subcommittee of the Senate Committee on Public Lands and the statements submitted at these hearings last fall placed the situation, its causes and the logical remedy, clearly on record. It was established at the hearings that for several years the volume of oil discovered per wildcat well drilled has steadily declined; new fields discovered have not been of major proportions; drilling costs have advanced rapidly; a sharp decline in exploratory drilling took place in 1942, while the proportion of dry holes increased; the inescapable conclusion is that to find new reserves the search for oil must be intensified and much more wildcat drilling ' must be done. To ensure an adequate drilling campaign, the Petroleum Industry War Council, the Interstate Compact Commission and other representative oil organizations have voiced by resolution their opinion that an upward revision of crude prices is necessary to provide an incentive to the prospector to undertake the hazards of wildcat drilling, since statistics prove that only ope in five or six wells drilled results in actual production. Former Price Administrator Henderson rejected the recommendations for price increases and declared himself unalterably opposed to a general price advance, On the ground that such advances would contribute to inflation. Now that Mr. Hender-

Jan 1, 1943

By D. C. Williams, D. V. Carter

Four oil discoveries were made in east and east central Texas during 1940, three of which represented new fields. In the Chapel Hill field, Smith County, oil was found where formerly only gas and distillate were produced. The three oil fields discovered are: Hawkins, Wood County; Pittsburg, Camp County; and Tehuacana, Limestone County. Important extensions were made to the following fields: Bazette, Navarro County; Long Lake, Anderson and Leon Counties; Cayuga, Anderson, Freestone and Henderson Counties; Opelika, Henderson County; and Talco, Titus and Franklin Counties. At the close of the year 54 oil and gas fields were producing in the district. There were 13 other fields, 11 oil and 2 gas, which have been abandoned. The East Texas field led the district in the number of completions for the year. During the year about 622 wells (oil and distillate wells included) were completed and 80 wildcats were drilled. Production and Proration During the year 170,424,685 bbl. of oil (distillate production included) were produced in the district—a decrease of 2.6 per cent from the 175,053,729 bbl. (distillate production included) during the preceding year. The district's production for the year 1938 was 182,369,484 bhl. As usual, most of the district's annual production was in the East Texas field, which produced 139,095,694 bbl. (distillate production in- cluded) during 1940, or 81.6 per cent of the total oil produced as compared with 141,333,317 bbl. (80.7 per cent) for 1939. The December estimated daily average production in the district was 424,565 bbl. The district accounted for 34.9 per cent of the state's annual production, compared to 36.7 pcr cent of the state's 1939 production. The decrease in production for 1940 may be attributed to changes made in proration schedules. Any material changes in the district's annual production may be considered for the most part as a reflection of proration-schedule changes affecting the East Texas field, since it is by far the most important field in the area. The entire state was subject to 71 shutdown days for the year; the East Texas field to 131; and the Rodessa field (Cass County, Texas, portion) to 5 days. No important changes were made in field rules and regulations during the year regarding the allocation of oil in individual fields in this district. Discoveries The Hawkins field is in southeastern Wood County in and principally north of the town of Hawkins. Development to date indicates that the field is somewhat of an elongated anticline trending slightly east of north and the proved oil area appears at this time to cover approximately 4000 acres. The oil production has been secured from the Woodbine sand, Upper Cretaceous; a considerable quantity of gas has been encountered in the Sub-Clarksville formation (Eagleford shale) in the higher part of the structure. It appears that a free gas

Jan 1, 1941

By David B. Reger

Wildcat drilling for new supplies of gas and the expansion of previously discovered oil and gas pools were the principal petroleum activities in West Virginia .during 1942. Much of the new gas exploration is still uncompleted and still indecisive but various wildcats made substantial extensions to existing pools. Out of 53 wildcats drilled 27 resulted in commercial gas and 6 in commercial oil. Four of the oil discoveries also had commercial gas. No strictly new pools of oil or gas can safely be described as discovered but several scattered oil and gas wells previously drilled have been confirmed as the openers of definite pools; also, various completions closed wide gaps between apparent gas pools already discovered. The proved oil territory of the state was increased about 4850 acres and the proved gas territory about 51,000 acres. The new proved oil reserves should about balance withdrawals and the new gas may represent a substantial increase. Aside from the drilling in four rather lively pools, oil activity was slight because of unfavorable operating conditions and prices. Gas drilling also declined for reasons beyond the control of the operators. The account of operations, as gathered from trade journals and other reporting services, shows that 797 new wells were drilled, providing 119 new oil wells with 2762 bbl. of daily new production; 536 new gas wells with 1,228,501,000 CU. ft. of daily open flow: and 142 dry holes. Also... 76 old wells were drilled to deeper sands, with 71 bbl. and 26,034,000 cu, ft. of added production. On the new wells the oil average was 23.21 bbl. per well per day; and the gas average was 2,270,406 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 17.82 per cent. On deeper drilling the ratio of failures was 21.05 per cent. Production of oil for the year was estimated by the Oil ad Gas Journal as 3,492,000 bbl., as compared with 3,378,000 bbl. in 1941. Production of natural gas for the year is estimated by the author as 220,000,000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 207,000,000,000 cu. ft.* in 1941. General State op Industry Leasing of wildcat acreage increased considerably. The total land of all classes under lease may now exceed 5,000,000 acres. Taking into consideration completions, abandonments and corrected figures or estimates, Table I shows cumulative and late annual statistics. New Pools and Extensions Table 2 shows the principal areas of drilling activity during 1942. Various consolidations of territory, hitherto treated as separate pools, have been made. in addition to these active pools, extensive drilling was done in numerous other areas where pool boundaries can hardly be defined. Summary or Exploration Table 3 gives a summary of important wildcat or exploratory wells drilled during

Jan 1, 1943

By Harold Vance

The Lafitte field, the largest oil reserve in South Louisiana, is in Jefferson Parish, some 25 miles due south of the City of New Orleans. The discovery well, The Texas Company's No. I, Louisiana Land and Exploration Co., in the southeast corner of sec. 19, T. 17 S., R. 24 E., was completed on May 15, 1935. The initial production of this well was 960 bbl. of 34.9º A.P.I, gravity oil per day, through 1/4-in. choke, with a tubing pressure of 1600 lb. per sq. in. Producing depth was 9558 to 9572 ft., the total depth being 9572 feet. The development of the field has been at the rate of three to eight new producing wells per year. Up to Jan. I, 1944, 60 producing wells and three dry holes had been drilled, while two of the original producing wells had been abandoned, Although the field is not unitized, The Texas Company was the sole operator in the field until the Lafitte Oil Co. completed its NO. I Jefferson Parish, near the center of the west line of the NW/4 sec. 20, T. I7 S., R. 24 E., on July 27, 1941. No additional wells have been drilled by the Lafitte Oil Company. Drilling and WeLl-completion Practices All drilling operations have been conducted with the steam-driven rotary equipment mounted on submersible barges. A canal is dug to the well location and the drilling unit is floated into position. The seacocks are then opened and the barge settles to the bottom. After the well is completed, seacocks are closed and water is pumped out of the barge. This procedure permits the barge, with drilling equipment still in place, to be floated and moved off the location. The conventional open-hole and the gun-perforation method of completing wells has been used in this field. Where possible, the initial completion is from the deepest 'sand and recompletions are made progressively up the hole, by plugging back with cement to the upper sand and gun-perforating opposite the new sand. The oil string usually is 7 5/8 in., 26 to 34-lb. casing. Three wells have been completed using 9 5/8-in. 44-lb casing set below 10.000 feet. Fig. I shows the completion and recom-pletion practices on one well in the field. This figure also shows the relative locations of the different producing sands as shown on the electric well log. Structure The structure is an elongated dome, cut by two north-south faults, which divides the field into three segments. The west segment is the highest structurally and contains most of the recoverable oil and gas. The center segment is less important and the east segment is of little value. Figs. 2, 4, 6, 8 and 10 are depth contour maps on top of the five main producing sands in the field. These maps show the relative size of the five reservoirs and the

Jan 1, 1945

By W. M. Johns

The geological mapping of Lincoln and Flathead Counties was a five-year project undertaken by the Montana Bureau of Mines and Geology. This paper, written by the Project Geologist of the survey, is primarily concerned with the stratigraphy of the Belt rocks encountered in mapping. Lincoln and Flathead Counties of northwestern Montana are underlain by sedimentary rocks of the Belt Series of Precambrian age. In only a very small part of the area, near Libby and Troy, have economic mineral deposits been worked with any success. Most of the area has been inadequately mapped as to geology. The region is crossed by the Great Northern Railway and served by the Pacific Power and Light Co.; officials of these two companies believed that with better geologic maps, prospecting might be stimulated and lead to the discovery of mineral resources that would contribute to new economic development within the area. A cooperative mapping agreement was proposed jointly by the two companies to the Montana Bureau of Mines and Geology in May 1958, and thus was born the Kootenai-Flathead five-year project. The dual objectives of this project are: 1) the possible location of mineral deposits of economic value, and 2) the ''stimulation of prospecting exploration" by others. This was to be achieved by geologic mapping of some 6800 sq miles and by establishing a field office in Kalispell where prospectors could come to have their rocks and minerals identified and receive geological advice on their problems. This writer has finished four field seasons as Project Geologist and thus became familiar with the Belt section in the Libby, Yaak River, Ural, Thompson Lakes, Pleasant Valley, and Stryker quadrangles (see Fig. 1). Progress on the project is given in annual reports issued by the Bureau.* This *Montana Bureau of Mines and Geology, Bulletins 12 (1959), 17 (1960), and 23 (1961). paper is concerned essentially with the stratigraphy of the Belt rocks so far encountered in mapping. PREVIOUS WORK IN THE AREA Willis28 made the first study of the stratigraphy and structure in the Lewis and Livingston Ranges of Glacier Park just east of the project area. In 1904, Daly made a study of the Belt rocks of the 49th parallel, using the names from bottom up, Creston, Kitchener, Moyie, and Gateway, for rocks ranging in age from that of Prichard to that of basal Missoula group. Walcott26 studied the Belt rocks exposed in the Mission Range (see Fig. 1) and other areas to the south of the area under discussion. Calkins and McDonald made a reconnaissance of northern Idaho and northwestern Montana in 1905. Calkins was the first to use Walcott's term 'Ravalli' as a group name for the strata equivalent to the Burke, Revett, and St. Regis formations (see Table I). Clapp worked on the Belt of western Montana (including Lincoln and Flathead Counties) throughout his lifetime. The Fentons9 studied the Belt of Glacier Park and

Jan 1, 1962

By C. O. Tarr, G. V. Smith, R. F. Miller

METALLURGISTS have long recognized that the Fe3C type of carbide is not a stable phase in steel and that, given sufficient time, it will decompose with formation of graphite, at least at temperatures below about 2050°F.1 This slow graphitization has never been of much concern to users of hypoeutectoid steels, for in such steels it occurs only during prolonged exposure at elevated temperature. In 1935, Kinzel and Moore2 reported complete graphitization of the carbide of a 0.1 5 per cent carbon steel that had been in senrice for about 26,000 hr. at a temperature of about 1100° to 1200°F. In discussing this paper, both Mathews and Sauveur reported graphitization of slightly hypereutectoid steels. In an extensive investigation of graphitization of high-purity iron-carbon alloys, Wells1 produced graphite at 7o0°C. (1290°F.) in an alloy containing as little as 0.13 per cent carbon, and showed that graphite may precipitate either directly from austenite or from decomposition of Fe3C, also that the rate of graphitization tends to increase with increase of temperature, at least up to a certain point, and with the presence of graphite nuclei. Jenkins, Mellor and Jenkinson,3 studying the structural changes in carbon steels ranging from 0.17 to 1.14 per cent carbon during stress-rupture tests at elevated temperature, obsenred graphite in an aluminum-killed 0.40 per cent carbon steel after fracture in 4340 hr. under a stress of 17,900 lb. per sq. in. at 840°F. and in many of the steels after stress-rupture test at 1200°F. Unstressed samples of 0.60, 0.86 and 1.14 per cent carbon steels graphitized almost completely in 360 hr. at 1200°F., while samples of 0.90 and 1.10 per cent carbon steels were somewhat graphitized, and steels containing 0.24, 0.40 and 0.57 per cent carbon showed no sign of graphite. Their results indicate that graphite precipitates the more readily the higher the carbon content, though this tendency is influenced to some extent by deoxidation practice, and that graphitization is accelerated by plastic deformation. In a recent study of the graphitization of 0.4 and 0.6 per cent carbon steel strip, made by M. A. Hughes,4 it was found that at 1200°F. graphite appeared after 72 hr. in aluminum-killed but not in silicon-killed steel, and that the rate of graphitization was increased by slow cooling from 1600°F. and by cold-working prior to annealing. In creep tests of normalized o. I 5 per cent carbon steel killed with 2.5 lb. of aluminum per ton, at the U. S. Steel Corporation laboratory at Kearny, spheroidization and some graphitization were found after 3000 hr. at 1000°F. under a stress as low as 15m lb. per sq. inch.

Jan 1, 1944

By R. A. Deju, R. B. Bhappu

The basic structural unit of all silicate minerals is a tetrahedron with a silicon atom at the center and four oxygen atoms at the corners. The oxygen-silicon distance is about 1.6 & and the oxygen-oxygen distance about 2.6 &. The different types of oxygen-silicon frameworks in the various silicates are based entirely on the combinations of the tetra-hedral oxygen-silicon groups through sharing of oxygen atoms. In recent years, infrared spectroscopy has permitted estimation of the ratio of the ionic character of the oxygen-silicon bond to be a few times that of the oxygen-carbon bond and the ratio of electro-negativity of the two bonds has also substantiated this finding. On this basis, it is generally accepted that the oxygen-silicon bond is the strongest one occurring in silicate minerals. As the oxygen-silicon ratio increases from quartz to the olivines, a greater percentage of the oxygen bonding power is available for bonding to cations other than silicon. Hence, with an increasing oxygen-silicon ratio, there is increasing oxygen-to-metal bonding. Upon the fracturing of a silicate mineral crystal, the oxygen-metal bond, which is almost entirely ionic in character, should break more easily than the stronger oxygen-silicon bond, resulting in a greater number of unsatisfied negative forces on the surface. If, then the mineral is immersed in a liquid containing hydrogen ions, these negative forces should tend to be neutralized by hydrogen ions from solution, resulting in a change of the pH of the solution. An increase in the degree of adsorption of hydrogen ions is to be expected as the oxygen-silicon ratio in the crystal structure increases. This study attempted to correlate the oxygen-silicon ratio for various representative silicate minerals to the adsorption of hydrogen ions. Experiments to determine the effect of surface area on this adsorption and to investigate the effect of surface iron were also conducted. It is believed that such studies of the surface properties of silicate minerals will supply pertinent information about their behavior in froth flotation systems. EXPERIMENTAL PROCEDURE Ion Exchange: Carefully selected, hand-picked samples of the minerals investigated were dry-crushed in a ceramic ball mill and sieved to obtain a minus 100 plus 200-mesh sample. The sized samples were then run through the electro-magnetic separator to remove any iron-bearing particles. A 10-g sample of each mineral was placed in 100 ml of freshly deionized water previously adjusted to a pH of 3.50 with HCl. The beaker containing the sample and the water was placed under a bell jar from which the air was displaced at once by nitrogen gas from a tank. All experiments were carried out in a nitrogen atmosphere. The sample and solution were stirred gently but continuously during the entire experiment, the stirring speed being kept about the same for all runs. Changes in pH were followed with a Beckman Zeromatic pH meter and recorded on a

Jan 1, 1967

By Nicholas J. Grant, W. Michael Yim

The creep-rupture properties of nickel, in as-prestrained or prestrain-polygonized condition, were studied at 1300°F and 4000 psi, and also at 700°F and 26,000 psi. An improvement of strength was noted in both the as -prestrained and the prestrain-polygonized tests at each temperature. The as-prestrained tests, however, showed superior creep resistance to the prestrain-polygonized ones. From the results of X-ray and etch-pit studies, the strengthc gain was interpreted in terms of dislocation density and the stability of preformed substructures. COLD work is known to improve the strength properties of metals at low temperatures. At high temperatures, however, the strength improvement is often lost if gross structural changes, such as re-crystallization, take place prior to or during the test. Even in the absence of recrystallization, a prestrained metal may undergo structural changes— polygonization and the formation of well-defined subgrains—which importantly effect the resultant properties. The relationship between substructure and creep properties has received considerable attention in recent years. The work of wood1 indicated that the creep strength of aluminum and its alloys was closely related to the subgrain size. Hazlett and Hansen,2 and Ancker, Hazlett, and parker,3 working with nickel and nickel alloys, had shown that small amounts of prestrain at room temperature followed by a recovery anneal at 800°C (1470°F) improved the strength at both low and high temperatures. The strength gain was attributed to an increase in the number of subgrain boundaries as a result of the prestrain-polygonization treatment. More recently Coldren and Freeman4 studied the effect of substructures on the creep rate of nickel at 1550°F. Their conclusions indicated that the substructure size as measured by the number of boundaries was the factor that controlled the creep rate. In addition, the perfection of the subgrain boundary has been indicated to have an important role on the strength.' On the other hand, there are data which disagree with the above observations. Grant, Chaudhuri, Silver, and Ganow6 found no creep strength improvement by a prestraining treatment. In reviewing the role of subgrains on high-temperature creep, Shepard and Dorn7 concluded that the contribution of the subgrains to high-temperature creep strength was a minor one. Guard,8 in a recent study on poly-gonized nickel, has cast doubt on the validity of the postulate that subgrain size controls the creep rate. In the majority of the previous studies, the subgrain boundaries have been singled out as the most important factor in determining creep strength; however, there is no firm theoretical ground for the postulate that the subgrain boundaries act as effective barriers to dislocation motion.B910 Little effort has been directed toward the study of the relationship between creep strength and other structural variables, such as dislocation density, lattice strain,

Jan 1, 1963

By M. R. Tek, K. H. Coats, D. L. Katz

A large number of boundary value problems encountcred in unsteady-state heat transfer, fluid flow through porous media, neutron diffusion and mass transfer involve the solution of a linear, parabolic partial differential equation commonly refcrred to as the diffusivity equation, where U is the dependent potential variable. K is the diffusivity (hydraulic, thermal, neutron, etc.) and 1 is the time variablc. Solutions to Eq. I are available in the literature for a wide variety of initial and houndary conditions. The great majority of these solutions are ohtained for geometric boundaries corresponding to linear. cylindrical or spherical flow models. A typical engineering application where the solution to Eq. 1 is required is the calculation of underground water encroachment across the boundaries of oil or natural gas reservoirs, In this particular area of application, the reservoir boundary is invariably approximated by circular geometry. However. the areal shape of many reservoirs can be better approximated by elliptic rather than circular boundaries. Thus the need for a general method of solving the diffusivity equation in elliptic coordinates arises in this problem as well as in other engineering applications involving elliptic boundaries. The solution to the diffusivity equation usually in volves the Error Function for the linear flow model, Bessel functions for the radial flow model and trigonometric or Legendre functions for the spherical flow model. It is well known that the general solution to the diffusivity equation in elliptic coordinates involves Mathieu functions. The significance of Mathieu functions in the analytical treatment of the diffusivity equation in elliptic coordinates is discussed in the literature However, these references do not providc analytical solutions useful in practical engineering problems. The objectives of this papcr are the development of the equations describing the unsteady-state liquid flow through a porous medium with an elliptic inner boun- dary, the development of a numerical method of solving these equations and, finally, a comparison of the water encroachment quantities calculated from the elliptic flow equation with those calculated from the radial flow equation. While the specific problem treated in this paper relates to unsteady-state liquid flow through a porous medium, the basic equations and computational techniques devcloped will apply equally well to problems occurring in the other areas of engincering interest mentioned previously. The solution given here is limited to a single case in which thc outer boundary encloses an area 100 times that of the inner boundary. DESCRIPTION OF THE FLOW MODEL Fig. 1 shows the flow model upon which the calcu lations presented in this paper are based. The inncr and outer houndaries of the flow model are represented by two confocal ellipses with major and minor axes, respectively, equal to 2a1, 2b1, and 2a, and 26,. The height of the elliptic cylinder flow model is denoted by 17. The following assumptions are employed in the development 01 the equations governing the unsteady-state liquid flow through the described flow model. 1. Uniform porosity and permeability throughout the flow model

By G. E. Warner

This paper presents a review and analysis of a highly stratified Burbank sand waterflooding project in Osage County, Okla. Permeability values in this reservoir range from less than 0.1 md to nearly 3 darcys, and 90 percent of the permeability capacity is contained in approximately 26 percent of the reservoir volume. To date, the project has recovered 103 bbl/flood-acre-ft since waterflood initiation, which represents 50 percent of the total preflood cumulative and 12 percent of the original stock-tank oil in place (OSTOIP). The outstanding feature of this project has been the economical recovery of a sizable quantity of oil at water-oil ratios higher than those normally considered prohibitive. Nearly 70 percent of the recovery to date has been achieved at water-cut values greater than 95 percent. An ultimate waterflood recovery of 138 bbl/flood-acre-ft, or 67 percent of the preflood recovery and 16 percent of the OSTOIP, is predicted. The ultimate primary and secondary recovery will be 302 bbl/acre-ft and approximutely 40 percent of the OSTOIP. The actual performance is compared with the predicted performance by both the Stiles and the Dykstra-Parsons methods, and applicabiliry of these methods to this particular reservoir is evaluated. The performance of this project indicafes highly stratified reservoirs can be successfully and economically waterflooded when either reservoir or economic conditions preclude the use of mechanical and chemical means of mdbility control. Introduction The concept of the stratified reservoir has been used by reservoir engineers for many years to describe the vertical variations in permeability within a reservoir. Numerous techniques have been advanced to predict the expected waterflood performance of the stratified reservoir, and in most cases they prove reasonably accurate. The advisability of undertaking a prospective waterflooding project is determined, based on these predictions. This paper presents a review of a waterflood project in a highly stratified reservoir that normally would be considered a marginal prospect, at best, when evaluated with any prediction technique properly adjusted for reservoir conditions. This kind of project can be successful if the predictions are used to design a waterflooding system capable of economically recovering an oil cut of 1 to 2 percent. Experience gained in the early stages of the project's development was profitably applied in the later development of the entire reservoir and could prove beneficial to other projects with similar reservoir stratification or fracture characteristics. The East Burbank pool waterflooding operations have been developed in three separate stages, each of which has been a separate project: Mid-Burbank Unit, Flood A, and Stanley Waterflood. When referred to collectively, these projects will be called the Composite Project. The Skelly Oil Co.'s Barber lease — the only portion of the pool not included in the three projects — is operated as a separate facility with a cooperative injection-well agreement. It contains less than 80 productive acres and would not significantly affect the over-all performance picture.

Jan 1, 1969

By J. Mizrahi, A. M. Baniel, A. Mitzmager, S. Star

This article gives an account of the latest developments in the use of TBE for sink-float separation of silicate minerals. A number of minerals for which the process has been tested and found suitable are reviewed. Specific examples are discussed in relation to the particular problems of sink-float separation and recovery of TBE as compared with non-silicate minerals. The economic aspects are outlined. Silica and silicates comprise the most common and abundant group of minerals, and since they are present in variable amounts in most ores, they constitute an appropriate subject for the review and discussion of the recent developments in the use of TBE for mineral concentration. The silicates considered as a group have an extremely wide range of chemical and physical properties. Some of these properties, which are common to all minerals, are of importance to concentration by TBE and are discussed in some detail in this paper, as well as the development of methods and apparatus for concentration and recovery of TBE and several examples of concentration of silicates. PROPERTIES OF MINERALS WITH RESPECT TO CONCENTRATION BY TBE The properties considered as most important to concentration by TBE are specific gravity, structure, surface and shape. The specific gravity of a mineral is a fundamental property and is constant between very close limits for the same species of different sources if particles are pure and free from cavities or cracks. In many species, however, solid inclusions and changes in chemical composition due to replacement of elements cause variations in the specific gravity. The plagio-clase series of feldspars between albite and anorthite illustrate this point (specific gravity from 2.60 to 2.77). Fig. 1 shows the specific gravity distribution of some of the common silicate minerals.' The highest specific gravity is about 4.7 (zircon) and the lowest is 2.0 (sepiolite), with most of them ranging between 2.6 and 3.5. Although most of the silicates given in Fig. 1 are found as constituents of rocks, those generally considered as rock making minerals are comparatively few. They include quartz, feldspars, nephelite, sodalite, leucite, mica, pyroxenes, amphiboles, chrysolite, kaolin, talc and serpentine. These minerals may appear in igneous rocks as coarse crystals in granites, syenites and diorites or as very fine grained dispersions in basalt and felsite. When the latter rocks occur in an ore, their specific gravities depend on the minerals present and structure. The same is true for the sedimentary and metamorphic rocks (sandstones, shales, gneiss, slate, schists). A comparison of specific gravities for the minerals listed in Fig. 1 with that of TBE (see Table I) shows that the important rock-forming minerals, with the exception of pyroxenes, amphiboles and chrysolite (olivine), lie in the specific gravity range of less than 2.96 and can therefore be separated by TBE. The ore structure is important both in determining the apparent specific gravity and the efficiency of TBE recovery. The structure can be compact (as in

Jan 1, 1963

By C. A. Stickels

A heat of electrolytic iron, to whzch alunzinutn and nitrogen had been added, was hot-rolled, cold-rolled 90 pct, and recrystallized at temperatures from 500" to 700°C. Primary recrystallization textures appear to arise from competitive growth of two types of nuclei: 1) those having orientations belonging to the "usual" primary recrystallization texture found in riming steel, and 2) those with the {111} (110) ovientation. Development of a (111}(1 10) component in the primary recrystallization texture occurs only over a certain interval of isothermal recrystallizatzon temperatures when the material is supersaturated with respect to the precipitation of AlN. Lowering the degree of supersaturation depresses the temperature interval in which a (111)(110) component occurs. An elongated, 'pancake-shaped" recrystallized pain structure and a marked delay in the start of recrystallization were found in all specimens which were supersaturated with respect to A1N precipitation after cold work, regardless of their recrystallization texture. ONE of the consequences of killing low-carbon steel with aluminum is a significant change in recrystallization behavior. About 15 years ago, Solter and eatttiel showed that this behavior was largely controlled by aluminum and nitrogen in the steel. If complete precipitation of A1N was prevented before cold rolling, an increased "recrystallization temperature" was observed in subsequent. annealing, and the recrystal-lized grains were not equiaxed. Leslie et a1.2 studied this phenomenon in some detail and clearly demonstrated the relationship between A1N precipitation, recrystallization kinetics, and the development of "pancake-shaped" grains. It has also been known for some time that aluminum-killed steels, processed to produce elongated "pancake" grains, develop a (11 I}( 110) primary recrystallization texture. This texture has not been found in iron or low-carbon rimming steel as a primary texture4j5 but has been observed following grain growth in electrolytic iron.5 The present work was undertaken to study in more detail the effect of A1N supersaturation on recrystallization textures in iron. LITERATURE REVIEW The deformation texture in heavily rolled iron has been studied in detail by Bennewitz.~ The texture consists primarily of a partial fiber texture about a (110) axis in the rolling direction, designated here as fiber texture A. It includes the range of orienta- tions (111)[110] - (001)[ 110] - (11l)[110]. A weak secondary texture also is present.6 This is a duplex partial fiber texture about two (110) fiber axes located 60 deg from the rolling direction and 30 deg from the sheet normal. The range of this texture, designated here as fiber texture B, about the [101} fiber axis is (112)[110] - near (545)[252] - (211:1[011] *The range given here follows Bennewit~.~ A few pole figures from re-crystallized material indicate a broader range than this.' However, the components which are strongest in the recrystallization texture are in this range.'________________________________________________________ Primary recrystallization textures in unkilled steels can be accounted for by growth of members of fiber texture B present in the deformed metal.5 However, while members of fiber texture B dominate the primary texture, other orientations survive primary recrystallization as well. In particular, some {111}(110) members of fiber texture A must also grow during primary recrystallization, because a well-defined {1ll)( 110) texture develops during subsequent grain growth at 700°C.5 The unusual recrystallization behavior of deformed supersaturated solid solutions has been attributed to: 1) retention of the solute in solution,' 2) formation of coherent, preprecipitation solute clusters prior to and during re~r~stallization,~ and 3) formation of a precipitate prior to and concurrent with recrystallization.'~-'~ When aluminum is supersaturated with iron, the difference in grain boundary mobility between general high-angle boundaries and certain special coincidence site boundaries is apparently eliminated.' In aluminum-killed steels, precipitation of A1N can take place at ordinary subcritical recrystallization temperatures. The rate of precipitation increases with increasing aluminum or nitrogen contents.2'13 There is some doubt, however, as to whether true precipitates form during the time at temperature needed to complete recrystallization. Leslie ef a1.2 found that precipitation in one steel was complete after about 100 min at 700GC, or after about 1000 min at 650GC, as measured by chemical analysis for AlN. Aoki et a1.,13 using internal friction for dissolved nitrogen, showed that a large fraction of the dissolved nitrogen was removed from solution within a few minutes annealing time at temperatures from 400" to 800°C. However , the rate of formation of AlN, as detected bv chemical analvsis. was much slower than the apparent rate of nitrogen removal. Hasebe,'~~ using carbon extraction replicas, has identified A1N precipitates by electron diffraction in a 0.2 C steel, solution-treated at 1300°C and annealed 2 hr at 700°C. Borchers and kim,I6 also using a replication technique, observed precipitates after annealing treatments as short as 2 min at 640°C. However, Leslie et a1.' state that no A1N precipitate can be seen while recrystallization is being inhibited in aluminum-killed steel.

Jan 1, 1967

By C. Augustus Carlow

THE subject which has been allotted to me is so vast and far-reaching that it is impossible to deal adequately with it in the time available. A complete survey would occupy the spare time of any one man for many years, whereas the time available to me is measured in weeks In the circumstances, I have been fortunate in securing the aid of several willing collaborators, and shall endeavor to re present such information as presently exists in published form, examine the situation critically in the light of present-day conditions, and arrive at certain conclusions' which I shall venture to put forward for your consideration No one who has lived through the past 25 or 30 years, and who has witnessed the amazing achievements of recent scientific research, would venture to deny the possibility that new sources of energy-may yet become available, or to prophesy to what extent these may be harnessed to the service of mankind So far as we can see, however, coal, as a source not only of power and heat but also of that wonderful range of derivatives that form the raw materials of so many industrial processes, must continue to play a vital role in our economic life It is the chief mineral fuel, exceeding all other mineral resources in value, production and demand In value coal overshadows the industrial metals, while of the sources of energy-coal, oil, gas and water power-the first named is the most important Thus, for example, in the United States, coal as a fuel (that is, as a source of heat and power) is still predominant, the figures of percentage of

Jan 1, 1947

By S. V. Krusiewski, J. W. Gabelman

Regional metallogenic zones and areas of equal paragenetic range have been interpreted from a compiled metallogenic map. of Mexico. Mineralization gradients of the pattern subsequently identified extend inland from coastal zones of high-temperature mineralization, and join in a central longitudinal zone of relatively low-temperature mineralization, apparently leaving no zonal room for lowest temperature deposits. The striking regional zoning pattern can be correlated with regional deformation gradients of similar position and orientation. The gradients represent at least three major orogenic cycles in two structural belts. Paleozoic structural belts existed along each coast with deformation gradients diminishing inland toward a narrow, central peninsular craton. The Mesozoic-Tertiary Mexican (Cordilleran) belt covered the entire country with a gradient oriented toward the Gulf of Mexico. Most ore deposits in this belt are of Tertiary age, although Tertiary mineralization gradients seem to have "inherited" the pattern left by Paleozoic tectonic gradients. Mineralization gradients can be used to identify the regions most favorable for the occurrence of selected metals. A metallogenic province is characterized by particular proportions of various metals, and the relative proportions can vary from province to province; but within any province the same intensity of mineralization would produce similar deposits in different places. Declining intensity of minetalization produces different kinds and sizes of deposits in zones that are concentrically arranged around sites of strongest rock alteration. On a regional basis, districts of similar average intensity of mineralization occur in zones that generally parallel some tectonic grain with the result that tectonic deformation has been designated a principal cause of mineralization. Variations in the type and intensity of deformation would determine the type as well as size of metal deposits. Mexico is especially favorable for such a study be- cause of its great abundance and variety of epi-genetic mineral deposits in various lithologic, structural and tectonic environments. The concept is also useful in recognizing portions of Mexico favorable for the occurrence of specific metals. METALLOTECTONIC ZONING IN MEXICO Theory: In studies of individual districts and groups of districts throughout North and South America, areal zoning of metal deposits generally seemed to respond to the paragenetic sequence of iron, gold, copper, zinc, lead, silver, antimony and arsenic, gold and fluorite. However, the definition of district zones is greatly obscured by contemporaneous or rhythmic deposition of metals, especially in the middle of the paragenetic range, and by the common superimposi-tions of different generations of metals. Zones could usually be distinguished only for groups of metals, such as early precious metals, base-metal sulfides, sulfosalts and late precious metals. The best defined zoning in a district is normally the spatial separation of the greatest volumes of altered and metallized rocks.' Exceptions are districts representing the high- and low-temperature extremes of the mineralization range where the former creates a matrix for the latter. In most districts the total quantity of alteration products is greatly in excess of, and appears to be roughly proportional to, the total quantity of metallization products. Subsequent to the bicomponent nature of each district, the most important mineralogical feature is the great excess of one to several metals or minerals which results in a district identifiable as one of predominantly gold, copper, lead-zinc, fluorite, etc., although a great variety of other elements may be present. The para-genetic range for the abundant elements in any district is only a portion of the entire possible range for all the elements representing the complete process throughout the region. Early during investigations of this type, it became apparent that the consistent bicomponent character of districts allows two methods for studying epi-genetic mineralization patterns. One is to identify and plot altered rock "pipes,"* which are easily recognizable in the landscape by their anomalous

Jan 1, 1969

By Akinobu Kasami, Keiji Maeda, Makoto Naito, Masaharu Toyama

Gap electroluminescent diodes have been prepared by the vapor phase diffusion of zinc into n-Gap crystals which were grown from a gallium solution (10 wt pct Gap) doped with tellurium and Ga203. A marked improvement in the efficiency of the red electrolumines -cence has been achieved by heat treatment after diffusion. External quantum efficiencies of diodes annealed under optimum conditions are 0.2 to 0.6 pct at room temperature, or about 200 times higher than the efficiencies of diodes quenched after diffusion. The optimum dopant concentrations in the gallium melt from which the crystals were grown are 3to6 x at. pct Te and 4 to 8 x 10-2 mol pct Ga203. The efficient diodes are characterized by linearly graded junctions with an i-layer 0.1 to 0.2u thick. Annealing increases the emission intensity by a factor of 20 to 50 and decreases the current density to 1/3 to 1/8 that of quenched diodes at a given bias. The decrease in current is attributed to an annihilation of deep recombination centers in the depletion layer. The increase in emission intensity is interpreted in terms of an increase in lifetime of minority carriers and an increase in the relative intensity of red-to-infrared emission. The dependence of these quantities on the tellurium and oxygen doping levels is also discussed. A number of studies have been made of the red light emission from for ward-biased Gap diodes.' At room temperature this emission band is centered at 7OOO? with a spectral width of nearly 1000?. Low-tempera-ture photoluminescence indicates that this emission is due to either the radiative annihilation of an exciton bound to a pair of zinc and oxygen atoms substituting on nearest neighbor lattice sites2,3 or the radiative recombination of an electron bound to this Zn-O pair with a hole bound to an isolated zinc shallow acceptor.3 An emission band is also observed with a spectral peak at 9800?. This infrared emission has been shown to be due to the recombination of an electron trapped at an isolated oxygen deep donor with a hole trapped at an isolated zinc acceptor.4 The red emission from Gap diodes is fairly efficient at room temperature because the nearest neighbor Zn-0 pair forms a deep electron trap at 0.3 to 0.4 ev below the edge of the conduction band.2'4 In diodes grown by liquid epitaxy an external quantum efficiency of 2.1 x 10-2 (photon/electron) has been attained by heat treatment at relatively low temperatures.5 This heat treatment was found to increase the efficiency by a factor of 3 to 6. However, no detailed studies have-been reported on the effects of heat treatment. We can only cite Onton and Lorenz's work6 on the change ; in the relative intensity of red-to-infrared emission. Heat treatment has also been tried on junctions built in during growth, but contrary to expectations the efficiency decreased. In-diffusion is a simple and controllable method of fabricating p-n junctions. For Gap, zinc is generally used to form a p-type layer on n-type crystals. The emission efficiencies of in-diffused diodes are, however, extremely low in comparison with liquid epitaxial diodes.' Although efficiencies as high as 2 x 1O-3 have been reported, values from 10-6 to 10-4 are generally obtained by typical diffusion techniques. Out-diffused diodes are known to be a little more efficient than in-diffused diodes. Nevertheless, the quantum efficiency is at most 7 x 10- 3 and ordinarily of the order of 10-4.8 NO results have been reported on heat treatment of either in-diffused or out-diffused diodes. This paper reports a marked improvement in the efficiency of the red emission observed for in-dif-fused diodes as a result of heat treatment after diffusion. The method described reproducibly yields diodes with external quantum efficiencies of 2 to 6 x 10-3. The observed dependence of efficiency on annealing time and on doping level will be discussed in terms of the lifetime of minority carriers and the formation of Zn-O complex pairs. EXPERIMENTAL A) Diode Fabrication. The n-Gap crystals used in this study were grown from a saturated gallium solution by a slow cooling method.8 The Gap content in the gallium melt was fixed to 10 wt pct corresponding to a growth temperature of about 1100 Tellurium was chosen as the n-type dopant and added to the melt in concentrations ranging from 0.001 to 0.06 at. pct. Oxygen was added in the form of Ga2O3, whose concentration was varied from 0.004 to 0.2 mol pct. The resulting crystals were platelets with well-developed (111) surfaces. Typical electrical properties were Hall mobilities of 130 to 30 sq cm per v-sec and carrier concentrations of 1016 to 10" cm-3 at room temperature. Diodes prepared from crystals with relatively low doping levels, in which u = 130 to 100 sq cm per v-sec and n = 0.6 to 6 x 1017 Cm-3, were examined in detail. The p-n junctions were produced in these n-Gap crystals by the diffusion of zinc from the vapor phase by the following procedure. The platelets were carefully lapped on both sides to a thickness of 150 to 200 u while maintaining the (111) orientation. After being etched in hot aqua regia, the crystals together with the zinc were sealed in an evacuated 12 mm ID quartz ampoule 20 cm long. The crystals and the zinc were then separated from each other at opposite ends

Jan 1, 1970

By Hannon, J. W. G.

Silicosis is today's most important industrial disease and probably dates back to the Stone Age. Since the industrial revolution, increasing attention has been paid to those occupations where mineral dust is present in the air breathed by the workers. For many years it was assumed that the inhalation of all mineral dusts was hazardous. but investigations conducted in several countries pointed the statistical finger of guilt at free silica in any of its numerous physical forms as a dust of outstanding toxicity. Recognition of silica as the chief hazard has resulted in widespread use of the term "silicosis." Depending upon the concentration of finely divided silica dust to which the individual is exposed and the duration of exposure, silicosis may become a disabling condition in from one to thirty years. The structure of the lung and respiratory passages is such that only minute particles of silica can gain entry to the air cells in the lung (5 microns or under are most toxic). When these minute particles gain entry to the lung tissues they stimulate certain protective cells in the lung to multiply at an excessive rate. The cell's undergo inflammatory changes which result in nodular scars and a low-grade inflammation of the lung tissue. These progressive changes in the lung structure gradually encroach

Jan 1, 1949