Search Documents

By J. E. Dorn, L. A. Shepard

LOW and Gensamer' demonstrated a number of years ago that the yield point phenomenon in mild steels was associated with the presence of fer-rite soluble carbon or nitrogen. More recently the yield phenomenon in body-centered-cubic metals containing interstitials was rationalized by Cottrell' in terms of a simple dislocation model. Interstitial atoms interact with dislocations in two ways; they cause not only local expansions but induce local tetragonality in the lattice. Consequently, interstitial~ interact with the hydrostatic tension and shear components of the stress about dislocations. They tend to migrate toward the expanded regions of edge dislocations and to assume sites that relieve the shear stresses of screw dislocations. Thus, a dislocation saturated with solute atoms constitutes a lower free energy state than that obtained when the dislocation threads through the average composition regions of the matrix. A greater stress will be required to separate the dislocation from its atmosphere than to move the dislocation through the matrix. This factor gives rise to the upper yield stress, which is required to unleash a series of dislocations in a localized region. This local yielding is propagated across the specimen to form a thin band of plastically deformed material known as a Lueder's band, making an angle of about 45" to the stress axis. Once the band has formed, deformation continues at the lower yield stress by the spreading of the Lueder's band in the direction of the applied stress. Undoubtedly the spreading of Lueder's bands at the lower yield stress is accomplished by the high stress concentrations at the band fronts, which serve to induce continued unlocking of new dislocations in advance of the migrating band fronts. Cottrell and Bilby have shown that the dependence of the yield point on temperature can be deduced by assuming that thermal fluctuations aid the stress in unlocking small dislocation loops from their solute atmospheres. Once a loop that exceeds a critical size has been nucleated, the entire locked diqlocation is released and can migrate. Fisher4 simplified this analysis by assuming that the locking forces were short range, so that if the dislocation loop were displaced only one Burgers vector from its atmosphere, it would be unlocked. Applying his model to the special case of delayed yielding under a constant stress of the order of the upper yield strength, he demonstrated that the delay time 7 for yielding should depend on stress and temperature according to where A and B are constants, G is the shear modulus, and u and T are the resolved shear stress and absolute temperature, respectively. Cottrell and Bilby, Fisher, and Fisher and Rogers' have shown that the above deductions are at least in qualitative harmony with the experimental facts. A number of investigators5-0 have shown that the yield point phenomenon can also be induced in sub-stitutional alloys of face-centered-cubic metals. In general such yield points are not as pronounced as those encountered in body-centered-cubic metals containing interstitials. The yield point phenomenon in these materials is usually enhanced by prestrain-ing at low temperatures and aging at intermediate temperatures. Undoubtedly the yield point phenomenon induced by strain aging substitutional alloys also results from locking of dislocations. But the locking of dislocations in substitutional alloys of face-centered-cubic metals differs somewhat from interstitial locking of dislocations in body-centered-cubic metals. Substitutional elements in face-centered-cubic lattices cause only radial displacements of the adjacent lattice points. Consequently, only the edge components of dislocations can be locked by the mechanism suggested by Cottrell. Additional locking, however, can be obtained by the Suzuki mcchanism.10 In face-centered-cubic metals, dislocations exhibit lower energies when they are present in the

Jan 1, 1957

By C. R. Johnson, R. A. Greenkorn, R. E. Haring

Three confined five-spot miscible displacements at unity, favorable, and unfavorable mobility ratios were conducted in a shallow, water-saturated sandstone of Pennsylvan-ian age near Chandler, Okla. These studies, plus associated laboratory experiments, were designed to measure miscible displacement performance in a controlled natural system, using known scaling criteria to develop an approach to modeling the heterogeneous field system. We have concluded from these studies that: (I) displacement efficiency in the field is a pronounced function of mobility ratio, indicating that miscible fingering observed in simple laboratory models occurs in the field: (2) field displacements can be quantitatively predicted by scaled laboratory models if the degree and location of field permeability variations are preserved in the models: and (3) arbitrary simplifications of heterogeneity will not necessarily predict observed displacement efficiency, and the simpler the model, the more optimistic the prediction. INTRODUCTION Many processes to achieve miscible displacement of reservoir oil by injected fluids have been conceived and field tested by the oil industry. Among the better known are high-pressure gas, enriched gas, and LPG banks. The simplest form of miscible displacement—one fluid miscibly displacing another fluid of different viscosity but the same density—has been studied extensively in homogeneous laboratory models. Observations of unstable fingering have been made which explain the significant decrease in displacement efficiency as the mobility ratio (ratio of displacing fluid mobility to displaced fluid mobility) increases. General industry experience with field tests of miscible displacement projects, mostly LPG banks, has been premature solvent breakthrough and lower than predicted production rate increases. These results have been attributed to either unstable fingering, unusual or unexpected permeability stratification, or both. Miscible displacement data in a controlled natural system have never been reported, however. Also, it has not been shown that properly designed and constructed laboratory models quantitatively predict field-scale behavior. The purpose of the combined field and laboratory ex- periments reported in this paper is twofold. The first was to measure miscible displacement performance at different mobility ratios in natural rock approaching field size under precise, controlled conditions. The second purpose was to utilize known scaling criteria plus several approaches to heterogeneity to model the field. Comparison of model and actual field results should then determine whether or not the laboratory phenomena (manifested by miscible displacement efficiency) are exhibited in large, natural rock systems. We carried out our program by first locating a shallow, water-saturated reservoir whose rock properties were representative of oil-bearing reservoirs. Detailed reservoir description by core analysis and interference testing showed the field site to be heterogeneous. A sequence of controlled, aqueous-phase miscible displacements was conducted at unity, favorable and unfavorable mobility ratios. A central, confined pattern was used to obtain the displacement data. A laboratory program using sand-packed models was conducted to determine the modeling criteria necessary to simulate field behavior of miscible displacement in a heterogeneous system. SCALING THEORY The detailed derivations and descriptions of the scaling laws that apply to laboratory models of reservoirs are adequately described elsewhere, so the following discussion will be restricted to facets of importance in this study. For a displacement in which one liquid miscibly displaces another, the following dimensionless groups are required to have the same numerical value in the model as in the field: The model also must be geometrically similar to the field, be spatially oriented the same as the field (same dip angle), and have the same initial and boundary conditions as the field (same initial fluid saturations and same injection-production well arrangement). When these conditions are satisfied, the theory predicts that at dny dimensionless time (pore volumes of produced fluids) the dimen-sionless flow potential and dimensionless fluid concentrations will be identical at all dimensionless spatial locations within the model and the field. If this prediction is correct, then the local dimensionless velocities must be identical, thus the instantaneous fraction of displaced fluid produced and the cumulative recovery expressed as fraction of original fluids in place must be identical at all dimensionless times. The theory outlined above has been obtained by either dimensional analysis or inspectional analysis of differential

Jan 1, 1966

By Shiro Ban-ya, John Chipman

The effects of many alloying eletnents on the acticity coefficient of sulfur in liquid iron have-been studied by the equilibriutn in the reaction Sfin Fe) + Hz = HzS at 1550°C'. Results are expressed in terms of a concentration variable for a nonmetallic or for a substitutional metallic solute. Activity coefficient of sulfur, defined as increased by B, Al, C, Si, Ge, Sn, P, As, Sb, Mo, W, Co, and PI. It is decreased by Cu,Au, Ti. Zr, V, h'b, Ta, Cr, ,23n, and Ni. Irulues oj. the interaction coejficient 0i = 6 In are labulated. The same interactions are expressed also in terms of atom fraction and of weight percent. The thermodynamic properties of sulfur in liquid iron have been fairly well established. Our recent paper1 reported new determinations of activity coefficient up an atom fraction of 0.12 and equations based on a careful review of all published data. The effects of alloying elements on the activity of sulfur have been studied by several investigators,2"11 especially by Morris and Williams for silicon,' by Morris and Buehl for carbon,~ and by Sherman and Chipman for manganese. phosphorus, and al~minum.~ However, the effects of some important alloying elements remain to be determined. The purpose of this investigation was to determine the effects of many alloying elements on the activity of sulfur in Fe-S-j ternary systems. EXPERIMENTAL METHOD This study was based on experimental determination of equilibrium in the reaction at 1550°C: The same apparatus and procedure as described in our previous paper have been retained, and the same corrections were applied for dissociation of H2S. The alumina crucibles used in the experiments consisted of four separate compartments. In a given experimental run. kach of three alumina crucibles held four different samples of about 3 g each which reached equilibrium in the same gas atmosphere and temperature. The charges were made up of electrolytic iron, pure iron sulfide, and desired alloying elements, which were pure metal or master alloys made in the laboratory. The weighed samples were held for 4 to 12 hr in the prepared atmosphere at 1550°C. They were then low- ered to be cooled as quickly as possible. The quenched metal beads were crushed to avoid the errors of segregation in the ingot. The sulfur content was determined gravimetrically and alloy content by appropriate chemical analysis. CALCULATIONS The apparent equilibrium constants of Eq. [I] are expressed as follows from the corrected gas ratios and sulfur concentrations: The term K" is the observed equilibrium constant in any given ternary solution, K' is the value for the Fe-S binary solution. and the limiting value of K' in the infinitely dilute solution is designated by K, which is the true equilibrium constant in Eq. [I]. In the thermodynamic treatment of nonmetallic elements in a metallic solution, it has been suggested1' that the lattice ratio has certain advantages over other variables to express the concentration of solute. In interstitial solid solutions the lattice ratio zj is proportional to the ratio of filled interstitial sites to those which remain unfilled. The equations derived for the activity of the solute using zj as the concentration variable are found also to be applicable to liquid solutions containing nonmetallic solutes when the nonmetal is treated as if it were interstitial. For this purpose we adopt the following definitions: The quantity vj which is negative for interstitial solutes is taken as -1 for nonmetallic and +1 for metallic solutes. For purposes of calculation however ; j may be assigned a value which results in a linear relation such as shown in Figs. 1 to 15. The activity coefficient of sulfur, Qs, and equilibrium constant. K(z). are defined as follows: According to a Taylor series expansion. the logarithm of the activity coefficient of sulfur in Fe-S-j ternary system is: However, the value of 6 In */6zi remains constant through a broad range of dilute solutions and the terms of higher order are negligibly small. As a consequence, Eq. [6] is simplified as follows:

Jan 1, 1970

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. Ray Webb

A interest to geologists and to mining and petroleum engineers is a laboratory method for determining the dip and strike of sub- surface structures, as well as the direction of fault planes traversing them. The information is derived by making use of the magnetic properties of borehole cores which must show visible representations of bedding or fault planes. Complete knowledge of these factors aids greatly in the successful exploitation of both ore and petroleum deposits.

Jan 1, 1940

By A. Bauer, P. Calder, N. H. Carr, G. R. Harris

Since both rotary and jet piercing drills are used by the Iron Ore Co. at Smallwood, it is often desirable in planning to know in which regions of the orebody or new orebodies a particular drill will be the most economic. This makes it necessary to establish a correlation between drillability and pierceability and some physical rock properties. For rotary drills a good correlation was found with penetration rate and grinding factor index. The jet piercers were found to have a reciprocal relationship in the sense that the best rotary ground was the worst jet ground and vice versa. It is also indicated how an economic comparison could be made using these penetration rate versus grinding factor index curves, the hole size distribution curves for single pass and chambered holes and the mine distribution curve for grinding factor index. A discussion is presented on the fuel oxygen ratios to be used in jet piercing and on the site gas sampling and analysis which has been used to set up the drills. The fuel has been cut back so that stoichio-metric conditions exist, carbon monoxide is drastically reduced and pop-up or exploding holes eliminated. No decrease in penetration rate has been observed contrary to the published results of previous workers. The blasting procedure and results at Smallwood are discussed and the operation of Iron Ore Co.'s slurry pump-mix truck is also described briefly. Smallwood mine is part of the Iron Ore Co.'s Carol Lake operation and is situated in Labrador, 240 miles north of Sept-Iles, Quebec. Last year 15 million tons of crude ore were crushed to yield 6.3 million tons of concentrate and pellets. This year the figures will be 17 million tons of crude and 7% million tons of concentrate and pellets which is the full plant capacity. Carol Lake ores consist primarily of specularite and magnetite mixed with quartz. For convenience the ore has been split-into the following classifications depending on the percentage of magnetics in the sample, shown in brackets: specularite (0 to 10%), specularite-magnetite (10 to 20%), magnetite- specularite (20 to 30%), magnetite (>30%). The order of classification also represents the order of increasing grinding difficulty - the specularite generally being the easiest and the magnetite the hardest. The orebody also contains a small percentage of waste materials consisting of limonite carbonate, quartz carbonate and quartz magnetite. The first two materials are among the softest in the mine, generally softer than the specularite, and the quartz magnetite is amongst the hardest. The bulk of the material in the mine is of the specularite-magnetite and magnetite-specularite classifications. As a result of test drilling at Smallwood in 1960 with rotary, jet and percussion drills, the Iron Ore Co. purchased four JPM-4 jet piercers for the bulk of production drilling and set up an oxygen plant to supply 20 tons of oxygen per day. This oxygen is sufficient for two machines operating full time and one part time. In addition, there are two 50-R, one 60-R and one 40-R machines in use. The benches are 45 ft high and 50 ft holes are generally drilled. JET DRILLING At the onset of jet drilling in the late fall of 1962, two major problems were encountered: 1) freezing due to winter operations; experience and the use of heat at more places, such as the rotary head, has eliminated this,'" and 2) exploding or "popping" drilled holes; this happened frequently (several holes "popping" each day) and was the cause of two lost time accidents. In one instance a hole was being measured with a tape which fell down the hole causing it to "pop." Safety glasses though pulverized saved the wearer's eyesight. Various methods were then employed to detonate the holes before measuring or loading (dropping lighted rags of fusees down, or sparking across a spark gap). These methods were time consuming and far from completely successful. Consideration was given to the fuel oxygen ratio on the machines and what this would produce in the way of product gases. A fuel oxygen weight ratio of 0.35 which was quite oxygen negative was being used. Theoretically appreciable carbon monoxide would be produced at this fuel oxygen ratio. On the close down procedure of the jet which calls for low oxygen after flame out, oxygen would be left in the hole along with this carbon monoxide. This is an explosive mixture. The fuel oxygen ratio was cut back to stoichiometric

Jan 1, 1967

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit? The rocks are well-consolidated Gila conglomerate, quartz , monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ransome.3 In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special, fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3 1/4x4 1/4-in. tool joints; 8-in. bits, 2 3/4x 3 3/4-in. tool joints; 6-in. bits, 2 1/4 x3 l/4 -in. tool joints; 4-in. bits, 1 5/8 x2 5/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property, To allow for 2 3/8-in. drill pipe with tool joints, 3 1/2-in. core barrels and bits were used. With the standard 3 1/2-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 5/8 to 3 7/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven-machines. The open churn drill hole was cased with 2 1/2-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in unconsolidated material like the formations drilled by

Jan 1, 1952

By Arcy A., J. G. Davis, D&apos Shock

Results of a pilot operation in the Carlsbad Basin are discussed. After hydrafracing between wells, a block of potash was removed by solution techniques. The distance between frac wells was about 200 ft, the thickness of potash mineralization, 5 ft. By proper manipulation, a feed of concentrate brine was obtained. The ex-periment showed that the thin-bedded potash could be removed by the solution techniques. The details of well construction, method of operation, and removal rates are discussed. Continental Oil Co.'s laboratory research on the fundamentals of potash solution mining has been expanded by means of a series of field tests, and subjects such as well completion and hydraulic fracturing were added to the investigation. Both single-well and multi-well systems were studied in the field work. Discussion Background: The current paper discusses one field test in which potash was solution mined by a two-well system from a thin sylvinite zone. The potential economic value of solution mining evolves from (1) the use of drilled holes and solution techniques instead of excavated shafts and caverns and (2) the ability to mine both land and marine deposits through any type of overburden geology and below conventional mining depths. Recent interest has been focused on potash' and other soluble minerals, such as trona. Solution extraction minerals, such as copper and uranium, are also worthy of important consideration. In addition, many of the techniques are directly applicable to the construction of horizontal underground storage carverns in salt. There are two general approaches to potash solution mining. The first is to mine on a single-well basis, in which the same well bore is used for both injection and production. This method is slow, and the areal extent may be quite limited in other than very thick ore zones. The second, and the preferred approach, is to mine on a multi-well basis in which the solvent is circulated between wells. This technique, if applied in a manner which allows the ore zone to be mined from the bottom upward, results in nearly all the solution taking place from the cavern roof. Salt removal rates, therefore, are very much higher than from a single-well system.l Wells can be interconnected into a multi-well pattern by several means. One is to join single-well caverns in the lower part of an ore zone. Another is to use the hydraulic fracturing techniques developed in the oil fields.' We preferred the fracture approach because of its potential for creating the greatest area of salt exposure. Test Site Description: The field tests were conducted in New Mexico's Carlsbad Basin, where the potash deposits are flat and uniform over reasonable distances. Here, 12 potash zones are present in the massive Salado Salt section. The specific target was the Third Ore Zone which is about 4 ft thick at our location and about 1150 ft deep. The test pattern was designed in the shape of an equilateral triangle with a fourth well located in the center, 200 ft from each of the vertex wells. This configuration allowed the ore zone to be hydraulically fractured from the center well with good assurance that the fracture would intersect the bore of at least one outside well. Several multi-well test patterns would be available if the fracture connected all wells. Well Completion: Surface casing was set in the top of the Salado Salt at 600 ft to shut off water flows from the surface sands, and the salt section was drilled and diamond-cored to a point below the Third Ore Zone. A drilling fluid made of diesel oil with a small amount of emulsified water was used to drill and core the salt. This fluid was highly successful in preventing enlargement of the drilled hole and in promoting good core recovery. The three outside wells were completed by setting 51/2-in. casing at the base of a streak of anhydrite about 20 ft above the ore zone. Pipe was set high so that the intersection point of the fracture could be detected even if the fracture migrated above the ore zone as it progressed outward from the center well. The center well itself was completed by cementing 51/2-in. casing through the Third Ore Zone. Cement bond logs run on the center well have shown excellent bonding. Fracturing Practice: A mechanical tool was used to cut a notch through the casing and into the salt at a point about 1 ft below the ore zone in the center well. The purpose of this notch was to fix the point of fracture entry into the salt. The fracturing was done with water at injection rtaes as high as 30 bbl per min. The salt parted at 1450 psi; and it required only 5 min for the fracture to reach the well which was 200 ft to the south. It took about 5 min more to reach the other two wells. Caliper surveys were run to locate the point of fracture entry in the three outside wells. The fracture appears to have drifted downward slightly, entering the outside wells at the top of a streak of carnallite 8 or 9 ft below the ore zone. A cross section of the wells selected for the multi-well test is shown in Fig. 1. The figure includes KC1 values based on core analysis and the trace of the fracture plane between the wells.

Jan 1, 1971

By Billy L. Crowder, John M. Fairfield

The implantation of B+ , P+, and As&apos; into silicon has been studied with the purpose of making shallow p-n junctions. The influence of such parameters as 1) ion energy, 2) target orientation and temperature, 3) total dose, and 4) annealing schedule was investigated. An energy range of 70 to 300 kev was used for boron and phosphorus implants and up to 500 kev for arsenic. It is found that the experimental projected range agrees well with theory and that shallow junction depths can be made reproducibly. ION implantation has received much attention recently as a technique for doping semiconductors. Specifically, it has the potential of supplementing or replacing the diffusion process as a method for making p-n junctions. In a few specific cases it has been used successfully to make semiconductor junction devices. Potential advantages of ion implantation doping over diffusion techniques are: 1) It affords greater control of shallow junction depths (< 0.2 µ) while maintaining high peak concentrations. This is particularly important for high-speed switching devices, since lower junction capacitances and resistances can be achieved. 2) More precise registration of small planar structures can be realized if proper masking procedures are employed. This advantage is especially useful in the design of high-density integrated circuits. It has been used to advantage in FET fabrication since the edge of the source or drain can be aligned precisely at the edge of the gate electrode.&apos; 3) Ion implanatation permits lower temperatures than diffusion techniques. This factor alleviates the problem of compatibility of diffusivities often encountered when designing multiple-junction structures. Also, the lower temperatures create fewer thermal defects and dislocations, which may account for the high efficiency of some ion-implanted solar cells.2 4) Impurity profiles can be more easily tailored to resemble ideal distributions. Successful exploitation of the potential advantages of ion implantation techniques will depend on increased knowledge and understanding of the subject. The factors likely to be influential in determining impurity distribution profiles in ion-implanted single-crystal targets have been reviewed by J. F. Gibbons.3 In addition to the mass and energy of the implanted ion, the total dose, target orientation, and target temperature are important parameters. The annealing temperature required for removing lattice damage and incorporating the implanted species on an electrically active site is very important. This paper describes an investigation of some of these factors. Implants of boron, phosphorus, and arsenic into silicon have been studied. Energy ranges of 50 to 300 kev were used for boron and phosphorus and up to 500 kev for arsenic. In addition to the implantation energy, the effects of total dose, target temperature, and post implant anneal have been investigated. EXPERIMENTAL PROCEDURE The implantation targets were silicon wafers cut from Czochralski-grown crystals, lapped, and chemically polished. The orientations were (111), (110). and (100) with misorientations of up to 7 deg from the principal axis. For this study, accurate target alignment (i.e., within 0.1 deg) was not available and quoted misorientation values should be regarded as approximate . The implantation equipment consisted of an ion source, a 300-kev linear accelerator tube, an electromagnetic separator, and the associated target supporting and beam focusing assemblies. The ion source was a simple oscillating electron type source,4 which has been described elsewhere.5 The gaseous compounds BF3, PF5, and AsH3 were used as ion sources for B+, P+, As+, and AS+&apos;. Analyzed current levels of up to 20 pamp could be obtained; however, for this investigation target current levels of 1-3 µ amp were usually employed. The analyzed ion beam was collimated through a double slit (1.4 x 0.4 cm) and swept perpendicularly to the long axis of the slit such that an area of about 2 sq cm on each target was covered. Dosages of around 1015 cm-2 were normally employed, but smaller amounts were also used for comparison. A uniform flux density over the bombarded area was assured by the continuous use of profile monitors similar to those described by Wegner and Feigenbaum.6 Post-implant annealing was accomplished in an argon atmosphere in a temperature range of 600" to 950°C. It was not part of the purpose of this investigation to study the annealing kinetics; however, some isochronal and isothermal anneal experiments were conducted to determine the time and temperature necessary to render a reasonably high portion of the implanted ions electrically active (i.e., higher than 50 pct). Post-implant anneal temperatures of around 900° and 600°C were required for boron, and arsenic and phosphorus implants, respectively. Arsenic and phosphorus implants increased in conductivity rather abruptly at the proper anneal temperature of the isochronal curve, but boron increased more gradually over a wider range. Isothermal anneal curves were reasonably flat after 10 min, so an anneal time of 1/2 hr was used for the experimental results described below. The profiling techniques were: 1) neutron activation analysis, 2) differential sheet resistance,7 and 3) junction staining.8 The differential sheet resistance technique is commonly employed in this type of study. Its principal disadvantage is the uncertainty of the ef-

Jan 1, 1970

By Oliver Bowles

ALTHOUGH Oliver Bowles retired as chief of the nonmetal economics division of the Bureau of Mines last year, that retirement has not lessened his active interest in the field of nonmetallic minerals, in writing, nor in his hobby, cultivation of African violets. Excellent co-ordination of the timing of a professional meeting and a flower show permitted him on at least one occasion to attend technical sessions and take in the African violet exhibition which happily arrived simultaneously in one city. Dr. Bowles celebrated his seventieth birthday on Jan. 10, 1947, and

Jan 1, 1948

By J. L. SCHUELER

THE writer has reread Mr. Ingalls&apos; interesting article in the July, 1923, issue of MINING AND METAL- LURGY on "The Use of Spelter in Galvanizing." It seems that most writers, in commenting upon coatings of spelter on sheets and wire, dwell upon the thin coatings which these materials carry, and rightly so. However, they seem to forget that until very recently, in the case of wire, the manufacturer did not know how to apply a heavy coating of spelter to the wire, especially if the wire was to be woven into fence or fabricated in some other manner, because heavy coatings of spelter are exceedingly brittle. This is even true in the case of high-grade spelter, but to a lesser degree than with Prime Western. Because of this brittleness, it has been necessary for wire manufacturers to smooth the coating by passing the wire through tightly compressed wiping means of some kind, usually asbestos. This removes all of the excess spelter and allows only a thin coating to remain. The latter, as a rule, is malleable and the wire can be fabricated without material injury to the coating.

Jan 1, 1924

By P. G. Shewmon, H. E. Collins

We have studied the effect of adsorbed sulfur on the surface self-diffusion of copper using eight diflerent surface orientations and the grain boundary grooving method. The eight orientations studied were the four lying near the low-index surfaces—(loo), (Ill), and two directions in the (110)-plus four higher-index surfaces. Surface-diffusion measurements were made over a range of HZS concentrations (in Hz) from 3 to 1500 ppm between 830°and 1050°C. The results can be divided into two groups—Group 1 contains the two (110) surfaces while Group 2 contains the remaining six surfaces. In Group 1, increasing the temperature increases the effect of Hz S on DS for the Hz S range 5700 ppvn. Qs and Do increase with increasing H2S concentration in this Hz S range. Beyond this range, increasing the temperature decreases this effect on D,; also Q, and Do decrease. In Group 2, increasing the telnperature decreases the effect of H2 S on D, for the H2S range studied, and Qs and Do decrease with increasing Hz S concentration. In any study of surface phenomena, there invariably arises the question of the possible presence of and effect of adsorbed impurities. Such questions are well-founded since the presence of adsorbed atoms can sometimes produce marked changes in the kinetics of surface-energy-driven processes. In the last few years, values of the surface self-diffusion coefficient, D,, have been determined on a variety of metals by studying the decay of scratches or the growth of grain boundary grooves.L~3-L0~L3 Yet there has been relatively little work done in which the concentration of an adsorbed impurity was systematically varied and the effects observed. Work of this sort would provide some basis in fact for the assertions often made about the ro1.e of adsorbed impurities in the differences between the results of different workers in different atmospheres and on different metals. It also is relevant to those cases in which surface monolayers produce profound effects in commercially important processes. The most marked example of such effects is the ability of nickel or palladium to increase the sintering rate of tungsten by many orders of magnitude.&apos; The aim of this work was to study the effect of sulfur partial pressures on the surface self-diffusion of copper. It was felt that this in conjunction with a study of the degree of adsorption and type of active sites involvedL8 would provide a wide range of data for one system and hopefully lead to some insight into the mechanism by which sulfur adsorption influences copper diffusion. The main reasons for choosing the Cu-S system were, first, faceting was reported not to accompany the adsorption of sulfur. This is required if our experimental technique is to work. Second, Oudar has determined a high temperature adsorption isotherm for this system, an event which puts the Cu-S system almost in a class by itself.I4 EXPERIMENTAL PROCEDURE Initially, we considered studying the effect of an adsorbed impurity on surface self-diffusion of copper using isolated (or single) scratch smoothing as the technique and oxygen as the impurity. Copper was chosen as the material because the effects of orientation and anisotropy of the surface self-diffusion coefficient, D,, of copper in a dry hydrogen atmosphere had been studied extensively by Gjostein&apos; and by Shewmon and ~hoi.~,~ The isolated scratch technique was chosen because both the effects of surface orientation and anisotropy of D, in a given surface could be easily studied with this method.~ Oxygen was tried as the impurity because Robertson and Shewmon""~ had studied its adsorption on copper at 1000°C over the range of oxygen partial pressures of 10"22 to 10-l3 atm. After several preliminary runs, it became evident that neither the scratch technique nor the impurity oxygen would be satisfactory for this work. Scratching deforms an annealed surface so that the region near the scratches recrystallizes, thereby disrupting the scratch profiles. One can avoid this by deforming the specimen sufficiently before scratching to give complete recrystallization on subsequent heating.4 However, as a result of Gjostein&apos;s success in scratching and annealing undeformed gold single crystals without local recrystallization,13 we attempted something similar with copper single crystals using a 0.7-mil diamond phonograph needle mounted in a Tukon hardness tester. All specimens recrystallized upon being annealed. Also, some copper specimens were sent to Gjostein to be scratched using his technique. The results were the same. As a result, the scratch technique was dropped in favor of the grooving of symmetric grain boundaries. Preliminary work using oxygen showed that faceting began to occur before oxygen adsorption had any measurable effect on D, at 938°C (at Pbo/P, = 0.12). Since heavy faceting would interfere with the measurement, we decided to use a sulfur-containing atmosphere (H2S/H2). Work by Oudar and Benard&apos; and Robertson" showed that sulfur absorbed on copper and that faceting was not observed.

Jan 1, 1967

"The power development at these falls, three miles below the city of Great Falls, was made in 1891 by the original Great Falls Water Power & Townsite Company, and the Boston & Montana Consolidated Copper & Silver Mining company, the predecessor of the Boston & Montana Reduction Department mentioned above.The dam is 746 feet long, placed a short distance above the crest of the falls, and giving an effective head, as now constructed, of from 42 to 44 feet. There are power houses on both banks, those on the south bank belong to the Great Falls Power company, the successor of the Great Falls \!\Tater Power & Townsite Company, and the Great Falls Electric properties. The water is led from the dam to these power houses through sheet iron pen-stocks the water wheels are of the horizontal turbine type, and of various sizes.The water is here carried from the dam to the power houses by an open canal or headrace, the walls of which are concrete. This headrace is 100 feet wide at the widest point. The available head was originally less than 40 feet, but this was increased to about 44 feet by means of flashboards and tailrace wall, seperating the tailrace from the main river and delivering the water to the river at a considerable distance below the power house, thus taking advantage of a considerable fall in the river below the sheer fall at Black Eagle.A total of about 12,000 horse power 1s developed at these falls, the Great Falls Power Company, and Great Falls Electric properties developing about 2,000 horse power, and the Anaconda Copper Mining Company developing the balance."

Jan 1, 1913

By AIME AIME

THIS year the Chairman of the Institute&apos;s Iron and Steel Division is THIS William Anderson Haven, better known to the membership generally as Bill Haven. The Division Chairman is an individual endowed with a broad perspective of the ferrous metal industry he result of his earlier experiences as a successful operating man in the working and management of blast furnaces and his later experiences as an engineering-consulting executive concerned with the design and erection of and steel works throughout the world. William A. Haven was born to iron steel in the Pittsburgh district on ;. 1, 1888, and in due time--or in 1909 graduated from Penn State with a Bachelor degree in industrial chemistry.

Jan 1, 1944

By AIME AIME

Change of Meeting from Birmingham to Chattanooga. In consequence of the disturbed conditions attending a long¬continued labor strike in Alabama, the meeting of the Institute was changed from Birmingham, Ala., to Chattanooga, Tenn., where it will. begin on Thursday evening, Oct. 1, 1908. Information. of this change bad been sent to the newspapers through the Associated Press, and by circular to all members, when news was received of the sudden and unexpected termination of the strike referred to. It was, unfortunately, too late to change once more the arrangements for the meeting. But it is hoped that the cordial invitation of the citizens of ,Birmingham may be renewed and accepted at a future time, not too remote. Office Facilities for Visiting Members. A separate room in the suite occupied by the American Institute of Mining Engineers on the ninth floor of the United Engineering Society Building, has been equipped with furniture and telephone extension for the temporary use of members of the Institute or of sister societies, or visitors suitably accredited. Members of the Institute visiting New York for a short time, who need office facilities during their stay, or members residing in the city. who need temporary office accommodation, can arrange to have set apart for their exclusive use a room, equipped with office furniture, telephone, etc.,. in the suite of the Institute. It is not the intention to give possession of the room to any individual for an indefinite time, but to offer to members of the Institute an opportunity to acquire a well-located, well-equipped business headquarters to carry on transactions which

Jan 9, 1908

By Hans-Jürgen Schaller, Horst A. Brodowsky

Activity coefficients of boron in palladium were determined at concentrations up to PdB0.23 by reducing B2O3 between 870" and 1050°C in a controlled H2-H2stream and measuring the resulting weight gain. The deviations from ideal behavior closely resemble those of the system Pd-H and are interpreted in terms of three principles: 1) The solute atoms occupy octahedral interstitial positions. 2) They donate their valence electrons to the 4 d and 5s bands of palladium, raising its Fermi energy. 3) The lattice strain energy is lower for two nearesl -neighbor interstitial particles than for two farther separate ones. SOLID solutions of hydrogen in palladium are a useful subject for studying thermodynamic aspects of the formation of alloys and of nonstoichiometric systems.1-3 The activity of hydrogen is readily measurable to a high degree of accuracy,4&apos;5 even at low temperatures where the deviations from ideal behavior are more pronounced, and its simple structure facilitates an interpretation of these deviations in terms of a detailed model. Two effects are discussed to account for the non-ideal properties:3 An "electronic" effect, connected with the rise of the Fermi energy, as electrons of the interstitial hydrogen atoms enter the electron gas of the metal, and an "elastic" effect, due to an interaction of the regions of strain around each interstitial atom. The electronic effect is based on the idea that the lowest energy levels of the dissolved hydrogen atoms are higher than the Fermi energy, so that the electron will not occupy a localized state but enter into the electron band of the metal.6 The elastic effect is based on the observation that dissolved hydrogen distorts and expands the palladium lattice. The hypothesis is put forward that the elastic strain energy is lower for two adjacent dilatational centers than for two separate ones; i.e., they attract each other. The resulting pair interaction can be used to calculate an elastic contribution to the thermodynamic excess functions by means of one of the statistical methods. This model permitted a detailed description of the solution properties of hydrogen in palladium3 and in palladium alloys.798 An extension of the approach to describe the excess functions of substitutional palladium alloys is possible.9 In order to further test and refine the model, an investigation of other interstitial alloys was started. Palladium dissolves considerable amounts of boron in homogeneous solid solution.10 The palladium lattice expands linearly up to nB = 0.23 (nB = B/Pd atomic ratio), the highest concentration studied." The expan- sion, extrapolated for 1 mole of interstitial per mole of palladium, is 17 pct of the lattice constant of pure palladium vs 5.7 pct in the case of hydrogen.12 The fact that the lattice expands rather than contracts is a strong indication that interstitial positions are occupied. According to neutron diffraction experiments, hydrogen occupies the octahedral sites of the fcc lattice.13 Unfortunately, this direct evidence is not available for the Pb-B system, mainly because of the high-reaction cross section of boron with thermal neutrons. However, by way of analogy and on the grounds of the rather close similarities between the two systems to be reported here, it seems safe to attribute octahedral positions to the dissolved boron, too. At higher boron contents, compounds of stoichiomet-ric compositions are reported such as Pd3B, which has the structure of cementite,14 so that a close structural relationship seems to exist with the system r Fe-C. In their study of hydrogen absorption in Pb-B alloys, Sieverts and Briining noted that alloys with an atomic ratio of about nB = 0.16 are no longer homogeneous15 This observation was confirmed in an extensive X-ray investigation.11,16 The phase boundaries of two miscibility gaps were established. One two-phase region was stable below a transition temperature of about 315°C and extended from nB = 0.015 to 0.178. The other one extended from nB = 0.021 to 0.114 slightly above the transition temperature and had an apex at nB = 0.065 and 410°C. All phases involved have the fcc structure of pure palladium with lattice expansions proportional to their boron contents. The occurrence of miscibility gaps, i.e., the coexistence of dilute and concentrated phases, points to an energy of attraction between the dissolved particles, in the Pb-B system as well as in the Pd-H system. The filling up of the electron bands seems to be analogous, too, in the two systems, as indicated by the hydrogen absorption capacit15,17,18 and by the suscepti bility of Pd-B alloys.l8 In both types of experiments, boron acts as an electron donor. A chemical method was used to measure the activity of boron in palladium. Boron trioxide was reduced in a moist hydrogen stream: B2O3 + 3H2 = 2B + 3H3O [l] At known activities or partial pressures of boron trioxide, hydrogen, and water, the activity of boron could be calculated from the law of mass action. The equilibrium concentration of boron corresponding to this activity was determined as the weight gain of the sample. EXPERIMENTAL The samples consisted of small pieces of foil of 0.1 mm thickness and about 100 mg weight. The palladium was supplied by DEGUSSA, Germany, and stated to be

Jan 1, 1970

By R. L. Mauger, P. E. Damon

Potassium-argon dating of the late Mesozoic and Cenozoic intermediate to acidic plutons and volcanic rocks of Arizona and northern Sonora demonstrates the existence of two distinct magmatic episodes. The earlier episode begins in late Campanian time and dies out before the middle Eocene. Following a quiescent period in middle and late Eocene time, magmatism increases in Oligocene time, becomes most intense at the Oligocene-Miocene boundary and dies out as the Pliocene is approached. Pliocene magmatism is primarily confined to extrusion of post-orogenic basalts. The late Mesozoic-early Cenozoic magmatic pulse is essentially confined within the limits of the classical Laramide orogeny (Laramie through Wasatch time). The mid-Tertiary pulse is contemporaneous with the mid-Tertiary Basin and Range orogeny. The Laramide provides an excellent specific example of Umbgrove&apos;s concept of the pulse of the earth and in general his concept appears to be meaningful. Copper porphyry mineralization is time-congruent with Laramide magmatism and there seems to be no doubt as to the existence of a genetic relationship between the two phenomena. Two origins are tenable: direct accumulation of the copper sulfides in the copper porphyry liquid magmatic environment; or, introduction of the mineral constituents entirely from a larger source magma when the host rock is already crystalline. Transgression and regression of the epicontinental seas provide an excellent indicator of orogeny and epeirogeny. There was an overall transgression of the epicontinental seas from early Triassic time through the Turonian epoch in early late-Cretaceous time. Thereafter, there is a relatively continuous regression of the seas until the present time. Both the earlier transgressive episode and the later retreat are intermpted by temporary but distinct reversals. These interruptions can be correlated with classical orogenies. There are six distinct orogenies so indicated in the Mesozoic-Cenozoic eras. These occur at approximately 35 to 40 m.y. intervals. The regression of the epicontinental seas following the Turonian epoch was contemporaneous with the deepening of the Pacific ocean basin over the Darwin Rise. As the Darwin Rise was collapsing the East Pacific Rise was being elevated. The Western United States, situated on the eastern flank of the East Pacific Rise, was upwarped and tilted toward the east. Epeirogeny is the primary consequence of processes that operate on a global scale. Orogeny is an exothennic process that is limited in space and is treated here as a secondary consequence of epeirogenic-initiated warping. The off-campus buildings of the University of Arizona Geochronology Laboratories rest on the volcanic rocks of Tumamoc Hill. From this hill, the observer may obtain a beautiful view of typical Basin and Range topography. The city of Tucson lies below, contained within the broad Santa Cruz basin and surrounded on all sides by characteristic NW-SE trending ranges towering as much as 7000 ft above the valley floor. Since the senior author arrived in Tucson eight years ago, a great deal more has been learned about the geochronology of this and neighboring basins and ranges. For example, the volcanic rocks underlying the laboratory at Tumamoc Hill were shown on the state geologic map as Quaternary basalt. A student of the senior author has demonstrated that the so-called basalts are in fact alkali-andesites (Halva, 1961), and we now know that these alkali-andesites or doreites (Mielke, 1965) are of early Miocene age rather than Quaternary age (Bikerman and Damon, 1965). Is it any wonder then that geologists disagree on the nature and time of Basin and Range volcanism, plutonism and tec-tonism? The plain fact is that few definitive Cenozoic fossil sites were available upon which to base a chronology and geologists were forced to guess the ages of rocks in order to achieve the semblance of a time classification. We have now made considerable progress in developing a K-Ar chronology for the volcanic and plutonic rocks of the Basin and Range (Bikerman, 1965; Damon and Bikerman, 1965; Damon et al, 1964 and 1965; Mauger et al, 1965). It is the purpose of this paper to point out the main features of this chronology and to discuss the relationship of magma-tism to orogeny-epeirogeny during post-Turonian time. We will also discuss probable relationships during

Jan 1, 1967