Search Documents

By David D. Rabb

Leaching or solution mining, a relatively simple and economical process for beneficiating metallic ores, is likely to find increasing application in the treatment of low-grade ores that are impractical to mine by any other means. This process may be carried out in two different ways: 1) dump leaching, where the ore is moved from its original location to be leached at another site; and 2) In-situ leaching, where the ore is leached in place by introducing the leach solution at the top, letting it flow down through the ore under gravity, and then recovering it plus the dissolved metals it contains. Whichever leaching method is used, it is almost always necessary to break up the ore before leaching. In this paper a study is reported which indicates that rock broken by an explosion-in particular, an underground nuclear explosion-is significantly more amenable to leaching then is rock broken by other methods. These results suggest that the leaching speed and efficiency could be increased by nuclear fracturing of the ore. Not only would the leach time be shortened, but the resulting increase in strength or richness of the solutions would decrease plant installation expense as well as reduce pumping and processing costs. A considerable fund of experience has been accumulated in the course of several hundred experimental underground nuclear explosions, so that the gross results of any given nuclear explosion can now be predicted with a fair degree of confidence.' From this knowledge it seems clear that, under the proper conditions, large ore bodies can be fractured much more economically-macroscopically speaking-by nuclear explosions than by other methods. The present study concentrates on smaller scale effects that is, the cracks in the chunks of rock broken by the explosion-and shows that here too, in the microscopic domain, there are important advantages to nuclear fracturing. The intense shock produced by the very fast acting, high-brisance nuclear explosive fractures the rock in a way that should significantly improve its leachability. Experimental Procedure This study compared rocks broken by nuclear explosives with rocks produced by conventional mining, quarrying, or core drilling. The test samples, granite chunks 6 to 8 in. on a side, plus core sections, came from the area of the Hardhat*2 nuclear explosion and were taken both before and after the explosion. For comparison, several samples of quarried granite were obtained from a local gravestone monument company. The general procedure was to soak the test samples in leaching solution and then determine the extent of penetration. A standard commercial copper leaching solution was used (10 gpl Cu, 10 gpl H2SO4, 5 gpl ferric Fe, 15 gpl total Fe, pH about 1.5), to which a water-soluble penetrant dye, Zyglo 1-c, had been added. Details of the procedure were as follows: 1) Sample leached in solution containing Zyglo penetrant dye. 2) Washed with water. 3) Air-dried. 4) Cut with granite wire saw. 5) One face polished with granite monument polish. 6) Sent directly to be photographed, or heated at 110°C for 2 hr and then sent to be photographed. 7) Photographed under ultraviolet light to show crack patterns. Results After 10 days of leaching at 70-75°F, the samples were removed from the solution, washed, dried, and cut in half with a granite wire saw to study the penetration of the leach solution. Since the Zyglo dye in the leach is visible under ultraviolet light, the degree of penetration of the leach (and hence the cracks in the samples) can be studied on photographs of the crosscut samples made under ultraviolet light. The photos in [Fig. 1] show how the leach solution penetrated various representative samples. Of the 71 rock samples examined, fractures were most frequent and prominent in samples from the rubble produced by the nuclear explosion [(Fig. 1D)]. Fracturing was less apparent in shaft-mined rock [(Fig. 1B)], still less evident in drift-mined rock [(Fig. 1C)], and practically nonexistent in cored or quarried specimens [(Fig. 1A)]. The samples in [Fig. lA-C] were from the same general area as the nuclear explosion, but they were obtained before the explosion. Results of the crack studies are summarized in [Table 1]. The Zyglo-treated leach solution penetrated the test samples at the rate of about 1/2 mm during the first hour, 1 mm by the end of 4 hr, 2 to 3 mm in 12 hr, and 4 to 6 mm in 10 days, showing a progressively slower rate with time.

Jan 1, 1972

By G. H. Bishop

The kinetics of the inter granular penetration and embrittlement of [100] tilt boundaries in 99.998 pct pure nickel upon exposure to bismuth-rich Ni-Bi liquids have been determined in the temperature range from 700° to 900°C. The kinetics of penetration are parabolic in time at constant temperature over most of the temperature range. In a series of 43-deg bicrystals the rate of penetration is anisotropic with respect to the direction of penetration into the grain boundaries. In lower-angle bicrystals the penetration rate is isotropic. The rate of penetration decreases with tilt angle at 700°C. The activation energy for penetration in the 43-deg bicrystals is 42 kcal per g-atom independent of direction. It is concluded that the intergranular penetration and embrittlement in the presence of the liquid proceeds by a grain boundary diffusion process and not by the intrusion of a liquid film. This was confirmed by a determination that the kinetics of penetration and embrittlement were the same in the 43-deg bicrystals upon exposure to bismuth vapor under conditions such that no bulk liquid phase would be thermodynamically stable. WhEN solid metals are exposed to a corrosive liquid-metal environment, the grain boundaries are sites of preferential attack. Depending on the temperature, the composition of the liquid, and the composition, structure, and state of stress of the solid, a number of modes of attack are possible. This paper reports a study of the kinetics of intergranular penetration and embrittlement of high-purity nickel bicrystals upon exposure to bismuth which, together with an earlier study by Cheney, Hochgraf, and Spencer,&apos; demonstrates that there are at least two modes of intergranular attack possible in the Ni-Bi system. In the study by Cheney et al., columnar-grain specimens of 99.5 pct pure nickel were exposed to liquid bismuth presaturated with nickel in the temperature range 670" to 1050°C. They found that the majority of the boundaries, which were predominantely high-angle boundaries, were penetrated by capillary liquid films, the attack proceeding by a process which will be termed grain boundary wetting. This process occurs in a stress-free solid when twice the liquid-solid surface tension is less than the surface tension of the grain boundary,* i.e., when 2yLs < YGB In this case the penetration of the grain boundary by the liquid occurs at a relatively rapid rate, resulting in the severe embrittlement of a polycrystalline solid. Grain boundary wetting is a common mode of intergranular attack in systems in which the lower melting component is relatively insoluble in the solid, but the solid has an appreciable solubility in the liquid, for example, the Ni-Bi system, Fig. 1. In systems of this type at temperatures above the range of stability of any intermetallic phases, once the liquid is saturated with respect to the solid so that no gross solution occurs, chemical gradients are small, and surface tensions become major driving forces for attack, provided the solid is stress-free. The results of Cheney et al. appear to be typical of those encountered when grain boundary wetting occurs.&apos; Capillary films were observed in the boundaries after quenching from the exposure temperature. The mean depth of penetration increased linearly with time, and the activation energy for the process was found to be 22 kcal per g-atom. In a study of the Cu-Bi system Yukawa and sinott4 found that the depth of penetration of bismuth into high-purity copper bicrystals of orientations from 22 to 63 deg of tilt about (100) at 649°C ranged from 0.05 to 0.25 in. after a 12-hr anneal. This corresponds to a linear rate of 6 to 15 X 10~6 cm per sec. At the same reduced temperature of 0.68 the rate for the Ni-Bi system&apos; was 7 x lo-&apos; cm per sec. In another study of the Cu-Bi system, Scheil and schess15 determined the kinetics of grain boundary wetting in hot-worked commercial rod. While there were several complicating factors present in this study, there is general agreement with the above results. The kinetics of penetration were linear, the activation energy was 20 kcal per g-atom, and at 650°C the rate of wetting was 2 to 5 x 10-6 cm per sec. The rate of wetting in the A1-Ga system6 is somewhat

Jan 1, 1969

By D. E. Spiller

Introduction Precious metals recovery from ore can generally be accomplished using gravity concentration, flotation, and/or hydrometallurgical (leaching) techniques. The objective of this paper is to show why gravity concentration can be an important part of recovery systems that employ leaching as the primary unit operation. A brief discussion of modem gravity concentration equipment is also presented. Discussion Gravity concentration of ores has generated increasing interest in recent years. Reasons for this interest include: • Gravity concentration is environmentally attractive. There is little or no use of reagents. Hence, it is relatively nonpolluting. • The cost of cyanide has continued to increase. Therefore, cost savings may be realized whenever leaching feed tonnage can be reduced by preconcentration. • Compared to flotation and leaching, gravity equipment costs are low per processed ton. Field installation costs for gravity circuits usually are less because many&apos; units are supplied as self-contained modules. Also, the cost required to supply services, particularly power, to a gravity plant site are also less. In situations where preconcentration at coarse particle size is applicable, significant grinding equipment savings may be possible. • Gravity circuit operating costs are also relatively low compared to typical flotation and leaching circuits. Reagents, power, maintenance, and manpower savings in a well-engineered gravity plant may be realized. Again, if grinding is reduced, significant power and steel (media and liners) savings are possible. •In recent years, more efficient gravity concentrating devices have been developed. Benefits to Precious Metal Leaching Gravity beneficiation can complement precious metal leaching in two ways. First, the recovery of coarse liberated values before leaching may reduce leach time requirements and may reduce reagent consumption. Second, gravity preconcentration can reduce the size of a leach plant by decreasing the quantity of material to be leached. Coarse gold and silver have been shown to leach rather slowly. Kameda (1949) and Habashi (1967) have investigated the kinetics of cyanide leaching systems. They concur that in a heterogeneous reaction, the rate of gold and silver dissolution is directly proportional to the surface area. Thus, the instantaneous rate of dissolution for spherical 0.37 mm (400 mesh) gold is theoretically -25 times faster than for the same amount of gold at .841 mm (20 mesh), based on data from Fuerstenau, Chander, and Abouzeid (1979). Conversely, coarse liberated, +.841 mm (20 mesh), gold is more readily recovered by gravity concentration than is fine, -.037 mm (400 mesh) gold. Therefore, it is apparent that the two recovery systems complement one another. Figure 1 data demonstrates the potential synergism. A sample of - 3.327 mm (6 mesh) Nevada gold-bearing ore was cyanide leached using conventional bottle-roll test procedures. Gold extraction was determined as a function of leaching time. A second sample split from the same leach feed material was hand jigged to remove a coarse heavy mineral fraction, including virtually all of the +.210 mm (65 mesh) liberated free gold. This second sample, with the coarse gold and heavy minerals removed, was subjected to an identical cyanide leach procedure. Figure 1 presents the resulting comparative extraction data. Note that the percent gold extraction for the sample containing no +.210 mm (65 mesh) free gold includes the coarse gold recovered by gravity. The data show that the sample containing coarse gold required about 72 hours of leaching time to achieve 80% extraction. This compared to about 22 hours of leaching time for 80% gold recovery from the sample that contained only -.210 mm (65 mesh) free gold. Thus, there was a 69% reduction in leaching time. The improved extraction data is not wholly attributable to coarse gold removal, but rather it was the combination of gold removal and rejection of other heavy mineral cyanide consumers or leach retardants. Further investigation was not warranted at this time. Preconcentration is the second manner in which leaching systems can benefit from gravity concentration. The premise is that preconcentration can reduce the quantity of leach feed, which, in turn, may reduce leaching costs. Figure 2 presents preliminary data developed by CSMRI for US Minerals Exploration (USMX). Centennial Exploration Inc., in agreement with USMX, is proceeding with evaluations to determine the suitability of various processing schemes for recovery of gold values from the Montana Tunnels property. The data shows how the ore can be preconcentrated by gravity techniques to result in a reduced feed tonnage to secondary extraction techniques, presumably flotation or cyanide leaching. Testing has shown that Reichert cones, followed by treating the cone concentrate on spirals, can deliver about 88% gold recovery in about 13% weight, that is, 87% weight rejection. Consequently, fine grinding and reagent costs are attributable to only 13% of the plant feed rate. Cost data is not yet available, but the potential exists for significant cost savings.

Jan 1, 1985

By V. C. Williams

Some of the physical, chemical, and electrical processes for conversion of saline water to potable or industrial water are economically surveyed from an engineering viewpoint. Since all these processes require energy for drive and equipment for containment, the correlative economic factors are developed which indicate directive influences in the choice of particular regional processes. The supply of natural waters and its distance also affect decision. Any one process will probably not prove dominant in the field because auxiliary considerations such as the saline water source; types and continuing availability of fuel; electric power use or recovery; area economic status and advancement; and the political pressures of population, group demands, and land use tend equivocally to obscure capital and operation cost decisions. Basic engineering considerations, data, and economic factors are presented to assist in the direction of these decisions. An exploding world population, increasing industrialization, advancing standards of living, and the desire of less-privileged nations for betterment focus attention sharply on a major problem: water. *19 Up to now, in retrospect, people have had it relatively easy in the handling of this problem. All the better dams in the most advantageous sites, the better aquifers, the shortest aqueducts have been built. In another phase of the problem, concern is evident that wastes cannot indefinitely be disposed of merely by keeping them dilute and discharging them promiscuously. 7-9 And, perhaps, as past civilizations have done,l5 water, watersheds, streams, and irrigation may have been mismanaged or, at the least, not adequately studied.3,5,36,37 In this last is perhaps the core of the problem. As Gross states, "Ignorance and too often, indifference are contributing factors. Archaeology and theology both furnish ample testimony to the existence of rich lands where deserts now stand; it was man who ravaged his land. Unless education is a companion to water development, development might as well be forgotten. But without water, there is no beginning."13 The U.S. is showing increasing concern about its water for predictions are that by 1980 the daily withdrawals will be 494 billion gal, a figure nearly equal to the dependable supply.Is This is based on a conservative projected population of 230 million. The major categories of withdrawals are: To make available this per capita average of 2150 gal per day will require an expenditure of $219 billion over the next 20 years. The U.S. is not alone in this concern. The United Nations shows as arid zones of the world: all of Africa north of the equator and south of the 20&apos;s parallel; all of the Arabian peninsula; all of the middle east and Iran, Iraq, Pakistan, Afghanistan, northern and central India; a great band about 1000 miles wide along the 40&apos;~ parallel from the Caspian Sea east across Russia through China to the Pacific Ocean; all of Australia except the coastal plain; the Caribbean Islands; the western nations of South America; and the western third of the United States and of Mexico. With one quarter of the earth&apos;s 57,500,000 sq miles of land thus suffering from lack of good water, increasing attention goes to the treatment of brackish and sea waters. The U.S. has been a leader in this field4,12, 16123,24 through its Office of Saline Water in the Dept. of Interior because even now some of its cities and regions are short of potable water. 11j&apos;7,M Industrial water is also of vital concern as a result of ever higher industrialization1,14122 Other nations, among them JaPan, Israel,13188 Germany, Union of South Africa, Australia, Netherlands, France, Yugoslavia, Russia, and groups such as the Organization for European Economic Cooperation (OEEC)&apos; are also diligent. The objective is low cost water, which means that both technology and economics have prominent roles in saline water conversion processes. TECHNOLOGY: SALINE WATER CONVERSION A number of reviews of methods have been made, principally by staff members of the Office of Saline Water (U.S. Dept. of Interior). Jenkins,31&apos;32 Gillam,34p

Jan 1, 1962

By J. M. Blank, V. A. Russell

When the nucleation of silicon on a sapphire substrate is accomplished by gradually decreasing the substrate temperature while subjecting it to a constant impingement rate of hydrogen and silicon tetrachloride, the resulting deposit is characterized by widely separated islands of silicon scattered over an "open sea" of sapphire. Analysis shows that nucleation takes place mainly on sites of large adsorption energy, about 85 kcal per mole, and small surface concentration, about 108 cm-2. Crystal growth proceeds rapidly on these nuclei and results in enough depletion of Sicl4 from the ambient gas to suppress further nucleation. The technological importance of single-crystal films on dielectric substrates has prompted considerable work on the deposition of silicon on sapphire. This paper is concerned with the deposition of silicon, by the reduction of silicon tetrachloride with hydrogen, onto heated sapphire substrates. The apparatus consisted of a temperature-controlled container for the silicon tetrachloride along with gas lines and flow meters necessary to convey a hydrogen-silicon tetrachloride mixture to a reaction chamber constructed of quartz tubing. Heat for the substrate was provided by means of an inductively heated graphite susceptor. The observations pertinent to the present discussion were made with an American Optical Co. high-temperature microscope which allowed us to make motion pictures of the deposition process at a magnification of approximately 50 times. Two main categories of experiments were carried out: one on determination of critical condensation temperatures and the other on the deposition of epitaxial silicon films on the sapphire substrates. Critical condensation temperatures were determined in the traditional way by raising the substrate temperature well above that at which condensation could be expected at the impingement rates being studied and then gradually lowering the temperature until the condensation of the first silicon was observed. This was done initially with ellipsometry-type detection but it was soon discovered that the deposits were occurring as widely separated islands and groups of islands scattered over an "open sea" of sapphire. We have called these archipelago formations. They were most easily detected by optical microscopy. Data gathered from experiments of this type have been collected in Table I. Motion pictures of the formation of archipelago patterns show that the nucleation period lasts about 10 sec if the substrate temperature and impingement rate are kept constant. Essentially all of the nuclei are formed in a few seconds and all subsequent silicon deposition merely adds to the size of the established nuclei. After an archipelago formation has matured at a given substrate temperature and impingement rate, it is very difficult to stimulate any further nucleation in the open space between islands. Lowering the substrate temperature will occasionally stimulate nucleation but increasing the impingement rate hardly ever produces any more new nuclei. It should also be emphasized that the nucleation rates appear to be very small, about 104 cm-2 sec-1. They will receive special attention in the analysis section. Another series of experiments was performed employing a systematic variation of substrate temperatures and impingement rates approximating those expected to produce epitaxy. Sapphire substrates with surfaces normal to the 2233 direction were used. In contrast to the procedure that produces archipelago patterns, these films were deposited by raising the substrate temperature to a desired value at which time the silicon tetrachloride and hydrogen flow was begun. Of course, these depositions produced mainly films that were continuous. After removal from the deposition chamber, the substrate and silicon film were examined microscopically to determine the nature of the deposit and by X-ray diffraction to determine the extent to which a single-crystal film had been achieved. Results of these experiments are summarized in Table 11. Of interest for the present analysis is the fact that epitaxy appears to be confined to a fairly narrow temperature range between about 1050" and 1150°C. This also will be discussed in the analysis section. ANALYSIS In this section we shall apply nucleation theory to the data presented above with the objective of testing

Jan 1, 1967

By Paul L. Russell

THIS is a progress report of an experiment being undertaken in cooperation with the Bethlehem Steel Corp., the Crucible Steel Co., and the Rock Bit Sales and Service Co., involving heat treatment of the shank ends of drill steel. This experiment is being conducted by the U. S. Bureau of Mines in its experimental mine, Mining Research Branch, Bluemont, Va. The purpose of the experiment is to determine the effect of an increase in the time the steel soaks in the furnace during the hardening heat. It has been thought that increasing this time produces a soft zone below the lugs resulting in a metallurgical notch that causes early failure. Each of the steel companies furnished enough 11/4 - in. straight carbon, hollow, round steel to make up 10 sets of drill steel, in each instance the steel bars were from the same heat. These sets of drill steel, consisting of 2-ft, 4-ft, 6-ft, and 8-ft lengths were fabricated by the Rock Bit Sales and Service Co. Special attention was given to the forging of the steel to produce the best rods possible. The heat treatment of all thread ends was identical and followed the best practice. The heat treatment of the shank ends of five sets of steel from each company produced a soft zone 2 to 4 in. in front of the lugs. It was decided that possibly the best way to obtain this effect was not to overlap the hardening heat but to let the steel soak for an additional 30 min before quenching. Therefore the only variable in the test steels is the length of time the shank ends were in the furnace. The remaining drill steel shanks were treated as follows: Heat treatment in pyrometer-controlled furnace at 1550°F. Quenching oil at 105°F to 125°F temperature. Areas for heat treatment were; shanks, 11 in.; threads, 9 in. Time at heat, standard practice, 20 min for 11/4-in. steel. Actual drilling tests were made in greenstone, (a metamorphosed basaltic rock), and in epidosite. Greenstone has a specific gravity of 2.96 and a compressive strength of 44,200 psi. Epidosite has a specific gravity of 3.26 and a compressive strength of 63,100 psi. All drilling tests were made using a 31/2-in. column-mounted, automatic feed drifter, with a controlled air pressure of 90 psi at the throttle. Tungsten-carbide bits of 2 in. diameter were used for all drilling. Contrary to expectations the drill steels that were allowed to soak for the additional 30 min before quenching performed better than the steels that were heat treated according to standard practice. This performance, as shown in Table I, was especially noticeable in the drilling of epidosite. The "longheat" drill steels furnished by Company "A" drilled 154 pct more minutes than the "standard-heat" steel. Expressed in feet, the "long-heat" steel drilled 114.60 ft more before failure than the "standard-heat" steel. The "long-heat" steel furnished by Company "B" drilled 37 pet more minutes or 60.39 ft more before failure than the "standard-heat" drill steel. The effect of the long heat treatment was not as evident when the steels were drilling in greenstone (Table II). In greenstone, the increase in minutes drilled by the "long-heat" steel over the "standard-heat" steel was 47 pet and 1 pet, respectively, for Companies "A" and "B."

Jan 1, 1952

By E. W. Felegy

THE need for improved mine communication to increase efficiency and to insure greater safety has long been recognized. General and unrestricted communication between all points underground, and between the surface and all points underground, is probably the least advanced phase of the mining industry. An ideal system of mine communication must require no fixed wire installations. The equipment must be small, lightweight, and readily portable, and the power requirements low. A system that can be used not only under normal circumstances but also in an emergency, when the continuity of wires, tracks, and pipelines may be disrupted, must function independently of any aid furnished by standard installations. Radio communication offers possibilities of meeting all the requirements necessary for an ideal communication system in underground mines. Transmission of signals must be achieved through one or both of two mediums, through the air in mine openings or through the strata. The results or lack of results obtained by early investigators showed conclusively that radio communication by space transmission cannot be accomplished effectively beyond line-of-sight distances in underground passageways. A radio system underground therefore must depend solely upon transmission through soil and strata. The application of radio to underground mine communication was investigated by many individuals and agencies at different times in the last several decades, but little success was achieved before World war 11.2-0, The results of experiments during the war, and further knowledge gained in experiments with vastly improved communication methods and equipment after the war provided the background for additional research in radio communication in underground mines. During 1950 to 1.952 the University of Minnesota sponsored an investigation to determine the possibility of developing: a system of radio communication universally applicable in underground metal mines in the Lake Superior district. The possibility of using radio equipment to determine the imminence of rock bursts in deep copper mines in that district also was investigated. The investigation supplemented previous and concurrent emergency mine communication studies of the U. S. Bureau of Mines. Testing equipment and laboratory facilities maintained by the Bureau of Mines at Duluth, Minnesota, were used in the research program, which was conducted as a mining engineering graduate research problem by the present writer under the direction of T. L. Joseph and E. P. Pfleider. The radio units used in the research program were designed and built to specification solely to conduct tests of radio communication in mines. Two identical units were used in all tests. Each unit contained a transmitter section, a receiver section, and a power-supply section, mounted on a single chassis. The entire unit was enclosed in a single 10x12x18-in. metal case provided with a leather-strap handle for carrying purposes. The front of the case was hinged to open upward and provide easy access to the single control panel on which all controls were mounted. Storage batteries supplied the operating power for all tests. Standard 6-v automobile batteries were utilized to provide adequate capacity to conduct tests for a full day without exhausting the battery. A frequency range from 30 to 200 kc was covered in eight pre-fixed steps on each unit. The carrier frequencies were crystal-controlled and amplitude-modulated. The receiver employed an essentially standard superheterodyne circuit and was sufficiently sensitive to detect signal strengths of 5 micro v. A heterodyne circuit was employed in the transmitter to obtain the low-carrier frequencies used in the units. Power output of the transmitter, usually less than 2 w, rarely exceeded 3 w in any test. Tests were conducted in mines on the Vermillion iron range in Minnesota, the Gogebic iron range in Wisconsin, the Menominee and Marquette iron ranges in Michigan, and a copper mine in the upper Michigan peninsula. All tests were conducted when the mines were operating normally, and usual mining, maintenance, and transportation activities were in progress, so that any interference caused by normal production activities could be evaluated during the tests. Tests were made between different points underground in each mine, and between underground and surface points at some mines. Test readings obtained at any one mine were calibrated in the laboratory before another series of tests were begun at the next mine. The transmitter and receiver were separated by one or more levels in each test, and generally there was no other means of communication between test points. Two 100-ft lengths of rubber-covered wire were used for antenna wires on each unit in both transmission and reception. The ends of the wires were connected to ground points in one of several methods, depending upon physical conditions at each test site. The wires were clipped to metal rods about 200 ft apart in the back, side, or bottom of the mine opening where the character of the rock permitted driving rods. Both wires were clipped to points about

Jan 1, 1954

By Ikuya Takase

INTRODUCTION Since the occurrence of the first oil crisis, coun-tries of the world, especially oil-importing countries have made sustained and vigorous efforts to lessen the dependency on oil as a source of energy supply. The adoption of "Principles of Coal Policy" by the IEA Ministerial Governing Board Meeting in May, 1979 was the first formal action taken by major energy consuming countries. At the Venice Summit in June, 1980, it was agreed that production and use of coal should be doubled over the next ten years. In fact, the world coal use in 1980 showed around a 10 percent increase over the previous year. Recently, we have seen an indication that the balance of oil supply and demand in the short term have eased. But I believe that it remains vital that we continue to encourage the development and introduction of alternative energy sources. Because, from the medium and long range viewpoint the recovery of the worldwide economy will lead us to increased oil requirements and thus we will be faced with the cyclical, structural tightening situation between the supply and demand of oil. Moreover, we are still convinced that the constraint of the supply capabilities of the Middle-East nations may be increasing in the long-term, since there still remains political uncertainties among these nations. Consequently, above all, coal is viewed as an alternative energy resource available for immediate expansion of use and is given as high a priority as nuclear power. In Japan, we regard coal as the most reliable alternative energy resource to replace oil. According to the "Alternative Energy Supply Targets" approved by the Cabinet in November, 1980, the level of coal imports is estimated to approximately double by 1990, while our domestic coal production will remain nearly at the same level. The transition from oil to coal is found in the recent import levels of coal---73 mil¬lion tons in 1980, a 23 percent increase over the 59 million tons imported in 1979. There was an upsurge in steaming coal imports, reflecting the transition in feedstocks---7.2 million tons in 1980, four times over the previous year&apos;s amount. Henceforth, from the medium to long range view, the demand for coal, especially that of steaming coal is forecast to continue to grow. The timely expansion of supply capabilities is our utmost concern and should be one of the most significant goals of our comprehensive policy. The Overseas Coal Investigative Committee, a privately organized advisory panel to the Director-General of the Natural Resources and Energy Agency of the Ministry of International Trade and Industry (MITI), investigated means to secure a stable supply of overseas coal. The panel presented its interim proposals in August, 1981, recommending the diversification of coal import sources, extensive use of low rank coal, as well as enhanced international cooperation between coal producing and importing countries. THE CONTENTS OF THE COMMITTEE&apos;S REPORT Four Points for Major Consideration In order to ensure a stable supply of overseas coal, Japan needs adequate policy measures consistent with the characteristics of coal resources and environmental requirements, giving consideration to Japan&apos;s status and the role she is expected to play in the areas. From the above, great importance should be attached to the following four points: All the components of the "Coal Chain" (Namely, the development of mine sites, construction of railroads, port loading facilities, coal shipping vessels, port receiving facilities, including coal centers and international transport facilities etc.) should be reviewed and reformed with steps taken to assure efficiency consistent with the entire coal chain system. The complete formation of a coal chain system requires such lengthy lead times and huge amounts of investment that necessary measures should be undertaken well in advance utilizing long-range projections of future demands and various economic surveys. Policy planning should be conducted taking into account of harmonizing stability and economics of the supply structure. For ensuring the long-term stability and expansion of the coal trade, international cooperation on a bilateral and multi-national basis should be encouraged. Mutual understanding and close relationships are essential to facilitate the formation of the supply system and to promote the extensive use of coal. Direction and Problems Related to Supply Stability Expansion of Supply Capabilities. World coal imports in 1979 amounted to 229 million tons, of which Japan&apos;s share amounted to 59 million tons, or one fourth of the entire amount. The imports of European and Asian countries accounted for 83 million tons and 7 million tons respectively. According to the examination of the Investigative Committee, Japan&apos;s coal requirement is estimated to be between 140-150 million tons by 1990, nearly the same level as announced in the Provisional Long-Term Energy Supply and Demand Outlook in 1979. This fore¬cast is-to be revised in April, 1982. Japan&apos;s demand is expected to be met through fiscal 1985; however, by 1990, the supply is estimated to fall short of demand, particulary, in the field of steaming coal. For the expansion of supply capability, first, mine development should be accelerated. The proposed

Jan 1, 1982

By Morris Cohen, Robert C. Ruhl

Fe-Ni-B alloys were inresligated by X-ray diffraclion after splat quenching. Although this rapid cooling did not produce a measurable supersaturation of dissol1ed boron in either binary Fe-B or Ni-B alloys, a marked increase in dissolved boron was achieved by the splal quenching of lernary Fe-Ni-B alloys. Boron additions up to 2.0 wl pcl to Fe-13Ni and Fe-24Ni alloys cause an increase in retained austenite from 0 to 59 pet and to 92 pet, respectively. The martensitic phase in the Fe-13Ni-9 at. pct B alloy is .found to conlain about 0.6 at. pet interstitial boron, as evidenced by the tetragonality of this phase, and about 3.6 at. pct substilutional boron, us deduced from the lattice paratrieler decrease, the balance of the boron being precipitated as (Fe,Ni)aR. The austenitic Fe-Ni-B plznses also contain both interstitial and substitutional boron. Iron-Boron System. The phase diagram and related information about the solid solutions and intermediate phases in the Fe-B system are given by ansen,&apos; Elliott.2 and Pearson.1 The equilibrium solid solubility of boron in both ferrite and austenite is quite small: the maximum solid solubility of 0.02 wt pct B (0.11 at. pct B) occurs in iron at the eutectic temperature of 1150°C. while the maximum solubility in a iron is less than 0.01 wt pct.l There is disagreement in the literature as to whether these solid solutions are substitutional or interstitial. Based on the measured activation energy of boron diffusion in iron, it appears likely that boron moves interstitially in austenite. 4 However, this observation does not rule out the possibility that some of the dissolved boron may also occupy substitutional sites in this phase. Investigations of internal friction of boron in iron have suggested that boron is interstitial there.&apos; Shevelev, 5 on the other hand, reports a decrease in the ferrite lattice parameter with dissolved boron content, thus indicating a substitutional solution. Unfortunately. Shevelev&apos;s methods and analysis are unclear. Goldhoff and spretnak6 have measured the lattice parameters of pure iron and an Fe-0.005 wt pct B (0.027 at. pct) alloy at both room temperature (ferrite) and from 920° to 1200°C (austenite). They reporte: a lattice contraction in the ferrite of 0.0003 ± 0.0002 due to boron, thus indicating a predominately substitutional solution. Appreciable (0.0010 to 0.0060) lattice contractions were found in boron-containing austenites, but these effects were much larger than could be accounted for by the substitutional solution of all the boron present. Nickel-Boron System. Elliott 2 gives a summary of thephase diagram and recent work on this system. The solubility of boron in nickel reaches a maximum of 0.03 wt pct at the eutectic temperature of 1080°C. Iron-Nickel System. ansen&apos; presents the equilibrium diagram for this system and also discusses the metastable austenitic and martensitic phases along with the a=? transformations. The lattice parameters of Fe-Ni ferrites have been recently redetermined by Abrahamson and Lopata.7 Their data, Fig. 1, show an unusual change in slope at about 1.7 at. pct Ni. Very few measurements of the lattice parameters of Fe-Ni martensites are available in the literature. The values of Roberts and Owen8 are considerably higher than those measured in the course of the present work: they find that a, is constant at 2.874? from 8 to 30 at. pct Ni. Both the slope change in the ferrite parameters and the occurrence of a maximum plateau in the marten-sitic lattice parameters vs composition denote the

Jan 1, 1970

By D. I. Bardos, Paul A. Beck

The 1100°c isothermal, sections of the V-Fe-Si, V-Co-Si, and V-Ni-Si systems were studied at silicon contents between 0 and 40 at. pct. The single-phase fields in the 30 and 50 at. pct Mn sections of the 1100°C tetrahedron of the V-&apos;Wn-Fe-Si system were also determined. The direction of extension of the elongated O, R, D, and a-Mn Phase fields suggests that the stability of these phases is determined largely by the electron concentration. The peculiar shape of the above ternary a phase fields, as well as of the a phase fields in the V-;Mn-Si and Cr-MTZ-Si systems is accounted for on the assumption that in manganese-(iron-, coball-, nickel-) rich alloys silicon atoms do not exclude d electrons , while in alloys low in the above components they do. This assumption also leads to the expected electronconcentrations for q and ß-Mn phases formed by transition metals with aluminurn. In earlier work it was shown that in ternary alloy systems of transition elements the a a and certain other phases with complex structure, such as the p and R phases,3 form elongated phase fields extending in a direction corresponding to a constant electron concentration. Recently similar behavior was observed in manganese-rich ternary ß-Mn solid solutions with another transition element and with silicon, germanium, or tin,4 confirming earlier indications3 that ß-Mn is also an electron phase. The alloying behavior of silicon in these manganese-rich alloys sug- gested that the four outside electrons of silicon participate in the bonding and that the predominantly d-like bonding electrons are not excluded from the silicon sites. Presumably, some of the normally unoccupied 3d states associated with the silicon atoms are in these alloys lowered to the Fermi level;4 thus silicon behaves as if it, too, were a transition element. The manganese-rich boundary of the a phase in the V-Mn-Si system,4 as well as in the Cr-Mn-Si sys-tem,4,5 extends approximately parallel to the ß-Mn phase boundary, corresponding to the transition ele-mentlike behavior of silicon described above. However, at lower manganese contents (i.e., in the high-vanadium or -chromium region) the a phase field in both ternary systems mentioned extends in a direction roughly perpendicular to that of its manganese-rich boundary, a phenomenon that is apparently inconsistent with the behavior of silicon in the manganese-rich alloys. A similar, although somewhat less pronounced, extension of the a phase occurs also in the high-vanadium (low-iron) region of the V-Fe-Si system at 1175C, but reportedly not in the V-Co-Si or V-Ni-Si systems at the same temperature.5 The present work was undertaken to investigate in more detail the extension of the a phase (as well as of other electron phases that may be present) in the last three systems and to elucidate this phenomenon, which has not been satisfactorily explained previously. EXPERIMENTAL PROCEDURES Most of the alloys were melted in an arc furnace, using a water-cooled copper crucible under helium atmosphere. The transition metals were of better than 99.9 pct purity and the silicon used was 99.98 pct pure. Alloys containing less than 20 pct V were induction-melted in recrystallized alumina crucibles under argon atmosphere.

Jan 1, 1967

By G. L. F. Powell

g samples of Cu-20 wt pct Ag alloy have been mdercooled to a maximum of 197°C by melting under a slag of commercial soda-lime glass in a vitreous silica crucible. No grain refinement of the primary copper was observed in samples undercooled to the maximum of 197°C. When the samples contained a small amount of oxygen, the copper dendrites were partially recrystallized at undercoolings greater than 97°C. In previous papers&apos;-3 reporting the grain structure of undercooled silver and copper, it was observed that grain refinement was dependent on both undercooling and oxygen content. Grain refinement occurred in undercooled silver when the degree of undercooling exceeded the range 153" to 175"C, while in Ag-0 alloys (0.12 wt pct) fine equiaxed grains were exhibited when undercooling was greater than 50°C. Similarly, copper samples undercooled as much as 208°C displayed fan-shaped growth from a single nucleation site, while the grain structure of Cu-O alloys (0.08 wt pct) was fine and equiaxed at undercoolings larger than 150°C. Thus the presence of oxygen greatly reduced the undercooling at which grain refinement occurred. It was also observed that the change in grain size resulted from recrystallization and was not due to an enhanced nucleation rate in the liquid-solid transformation. It is possible that the influence of oxygen on recrystallization is due primarily to its presence as a solute element. walker4,&apos; reported that, although a grain size change did not occur in pure nickel until the undercooling exceeded 150°C, small grains were observed in samples of Ni-Cu alloy solidified at small and large degrees of undercooling. Jackson et al.6 suggested that the fine grained structure of the Ni-Cu alloy resulted from the melting off of dendrite arms during recalescence. This remelting process may occur in alloys as a result of segregation during freezing which causes a variation in liquidus temperature from point to point within a dendrite. It was therefore decided to undercool copper with a metallic alloying element to ascertain whether the presence of a metallic solute would have a similar effect to oxygen in inducing grain refinement. A Cu-Ag alloy was chosen, since both metals had been shown to behave similarly on undercooling. The alloy Cu-20 wt pct Ag was selected since the eutectic constituent outlines the initial growth form of the primary copper, so that the as-frozen grain structure is not obscured if subsequent recrystallization occurs. This paper describes the results of undercooling experiments carried out with Cu-20 pct Ag samples undercooled to a maximum of 197°C and the effect of oxygen content on the grain structure of the undercooled samples. EXPERIMENTAL Melting was carried out in a small cylindrical resistance furnace using "fine" silver granulate and oxygen-free high conductivity copper. The procedure adopted was to melt the required quantity of silver in air in a clean vitreous silica crucible for approximately 15 min, freeze, and add granulated commercial soda-lime glass to form a complete surface slag cover, after which the sample was melted and frozen several times to reduce the oxygen content. The glass slag cover was approximately 3 in. thick. Pieces of copper (=50 g) were added to the crucible until the required quantity to make 350-g samples of alloy had been charged. Each piece was added quickly to the crucible which was held at a temperature slightly above the melting point of silver. The piece was quickly pushed beneath the glass to minimize oxidation and any oxide coating usually decomposed before the piece had settled down into the silver. After the full quantity of copper had been added, the melt was stirred with a silica rod to hasten homogenization and a Pt/Pt 13 pct Rh thermocouple enclosed in a vitreous silica sheath inserted for temperature measurement. Heating and cooling curves were recorded on a potentiometric chart recorder fitted with a zero suppression unit. The milli-voltage range of the recorder was adjusted so that temperatures could be read to 1°C. Heating and cooling curves were taken every hour until three consecutive readings gave the same solidus-liquidus range, consistent with the solidus-liquidus range for this alloy composition by reference to Hansen and Anderko.7 Metallographic examination of samples frozen at this stage, failed to show any variation in composition from bottom to top of the ingot. Consequently, it was considered that the melt was homogeneous at this stage and undercooling experiments were then car-

Jan 1, 1970

By C. E. Kemp, A. B. Dyes

Results of a field research project on the thermal recovery of oil by movement of a combustion front are presented. This field test was conducted in the South Belridge field, This The war paitern was a Southsing1e 2.5-acre five-spot pattern in the 700-ft deep Tulare sand. Results of this project indicate the technical feasibility of producing high viscosity, low-grallity crude oils by thermal means. It was demonstrated that heavy oils could be moved rapidly over considerable distances by thermal drive, and that high percentage recoveries of oil could be effected. The bulk of the oil recovery came after arrival of the burning front at a production well. However, rapid corrosion and high-temperature failure of conventional pipe and equipment both below and above surface occurred. Stainless steels gave more satisfectory performance under these conditions than did conventional steels. Oxygen was seldom observed in gas from wells ahead of the burning front, and it appears that the front was continuous throughout the life of the experiment. INTRODUCTION During late 1953 and early 1954, industry-wide attention was focused on the thermal recovery of oil by movement of a combustion front through an oil zone. Two separate Oklahoma field tests were described in publications by Kuhn and Koch, and Grant and Szasz. To obtain basic information needed for making engineering and economic appraisals of commercial recovery of heavy oil by this thermal recovery method, a new field research projecta3,4 was started May 31, 1955. Twelve oil companies contributed to this project with General Petroleum Corp. as operator. Since combustion recovery experiments* with heavy oils in other areas had been conducted in small patterns,"&apos; an important purpose of this test was to determine whether the process could be operated in a pattern of near-commercial well spacing. The south Belridge field, located 30 miles north of Taft, Calif., was chosen because its oil sands are similar to many heavy oil sands which typically have low primary recovery and leave a large amount of oil in place. such fields are not particularly suited for common secondary recovery methods. DESCRIPTION OF TEST SITE The test interval was a Tulare sand at a depth of about 700 ft. Nine test wells were drilled, cored and completed from Oct., 1955, through Jan., 1956. The initial pattern shown on the map, Fig. 1, consisted of an injection well (II)&apos;, four producing wells (1P-4P), and four observation wells (IT-4T). An old well (81) was also recompleted for use as an observation well. The area enclosed by the original four production wells was 2.5 acres; the distance from the injection well to each production well was 233 ft. During the combustion period, Well 5P was drilled to replace Well 2P, and Well 6P was drilled to replace Well 3P. The new wells were 25 ft beyond the old production wells along a diagonal from the injection well, and resulted in an increase in pattern area to 2.75 acres. Isopachs are shown in Fig. 1. The average thickness of the oil sand in the test pattern was 30 ft. Fig. 2 presents two cross sections through the test pattern. Oil sand is represented by white and claystone by gray. The dashed lines indicate layers of conglomerate grading to claystone. The sand thickness was fairly uniform throughout the test pattern except in the 1P area. The sand body dips gently from the northwest to southeast, about 3 degrees from horizontal. The sand is unconsoli-dated, and grades from very fine material to pebbles as large as 2 in. in diameter. Table 1 presents the average initial properties of the formation. The in-place porosity of 37 per cent was estimated from the porosity of coke-consolidated cores taken after combustion. Original core analyses data were adjusted to 37 per cent, giving pore volume saturations of 60 per cent oil, 37 per cent water, and 3 per

By Arthur F. Taggart

The following notes represent significant excerpts from a mass of records of experimental work done in the ore-dressing laborattory at the Columbia School of Mines during the years 1926 to 1928 inclusive. Classification of Experimental Work The experiments performed may be grouped for purposes of description under the following general headings: I. Collecting agents. a. A method for quantifying collecting effect. b. Coating with undissolved collecting agents (oils). c. Action of dissolved collecting agents. II. Frothing agent&apos;s. a. A method for quantifying frothing effect. b. Relation between frothing effect and chemical composition. III. Inorganic reagents. a. Methods of studying the effects of these reagents. b. Effect on slime dispersion. c. Effect on sulfides. Summary of the Origins of Present-day Flotation Practice The first practicable, foolproof method of froth flotation was described in U. S. Patent 835120, issued in 1906 to Sulman, Picard and Ballot, and in the equivalent patents in other countries. A number of less simple methods of producing the same result had been described previously in patent publications and otherwise.&apos; The reagents specified in all of these early patents were "oils" and, in addition, some inorganic substance, usually an acid. The quantities of reagents recommended and added were enormous when compared with those used today.

Jan 1, 1930

By Vard H. Johnson

IN 1943 the U. S. Bureau of Mines undertook drilling in an effort to develop new reserves of coking coal in an area near Paonia, Colo., as a part of an attempt to alleviate the shortage of known coking coal of good quality in the western United States. Geologic mapping of the area was undertaken by the U. S. Geological Survey with the purpose of first furnishing guidance in location of drillholes and later aiding in interpreting the results of the drilling. The drilling program was under the general supervision of A. L. Toenges of the U. S. Bureau of Mines. J. J. Dowd and R. G. Travis were in charge of the work in the field. Geologic mapping was started by D. A. Andrews of the Geological Survey in the summer of 1943 and was continued from the spring of 1944 to 1949 by the writer. The first few holes drilled failed to locate coking coal, but in the summer of 1944 coking coal was discovered by drilling 6 miles east of Somerset, Colo., the site of present mining. In the succeeding years, 1945 to 1948, 100 to 150 million tons of coal suitable for coking were blocked out by drilling. The ensuing discussion of the geologic controls on the distribution of coking coal in the area is based on the geologic mapping as well as the drilling done in the Paonia area, more complete descriptions of which have appeared or are in process of publication."&apos; In order that the possible geologic controls affecting the present distribution of coking coal may be considered, it is necessary to discuss briefly the indicators of coking quality coals. Coking Coal Coal that cokes has the property of softening to form a pastelike mass at high temperatures under reducing conditions in the coke oven. This softening is accompanied by the release of the volatile constituents as bubbles of gas. After release of the contained gases and upon cooling, a hard gray coherent but spongelike mass remains that is referred to as coke. This substance varies greatly in physical properties and, to be suitable for industrial use, must be sufficiently dense and strong to withstand the crushing pressure of heavy furnace loads. Western coals have a generally high volatile content and therefore form a satisfactory coke only when they attain a rather high fluidity during the process of heating arid distillation in the coke oven. When this high degree of fluidity is developed, the volatile constituents escape and leave a finely porous coke. On the other hand, when the degree of fluidity is low the product is an excessively porous and therefore physically weak mass that is called char." Small quantities of oxygen present in coal are believed to decrease the fluidity of the material during the coking process and to favor the development of char rather than coke. In consequence, coal chemists have for some time considered the possibility of developing an index to coking qualities by inspection of chemical analyses of coals.&apos; A formula has now been developed that does permit a rough preliminary estimate of the cokability of coal on the basis of the analysis on an ash and moisture-free basis. Coals may be eliminated as possible coking fuels if the oxygen content is greater than 11 pct. Similarly the ratio of hydrogen to oxygen must be greater than 0.5 and the ratio of fixed carbon to volatile constituents must be greater than 1.3. If the coal, on the basis of these limiting factors, appears to have possible coking qualities, the following formula permits determination of the coking index: a+b+c+d Coking index = -------- 5 a equals 22/oxygen content on ash and moisture-free basis, b equals two times the hydrogen content divided by oxygen content on moisture and ash-free basis, c equals fixed carbon/l.3 x volatile matter, and d equals the heating value on moist, ash-free basis/13,600. Coking indices higher than 1.0 suggest that the coal will coke, and indices above&apos; 1.1 indicate good coking tendencies. Although generally usable, this formula &apos;is not completely satisfactory because the percentage of oxygen shown in ultimate analyses is derived only by difference; i.e., by subtracting the sum of the percentages of the constituents determined analytically from 100 pct. Although the coking index indicates the coking tendencies of coal, it is necessary to make physical tests of coke before its industrial value can be determined. The U. S. Bureau of Mines has developed a standard procedure for determining the approximate strength of coke that would be formed from a given coal. In this test one part of ground coal, mixed with 15 parts of carborundum, is baked to form a standard briquette. The weight, in kilograms, necessary to crush the briquette is termed the agglutinating index. This test determines the relative fluidity attained in the coking process by measuring the cementing strength of the coal in the briquette. A

Jan 1, 1953

By Vard H. Johnson

IN 1943 the U. S. Bureau of Mines undertook drilling in an effort to develop new reserves of coking coal in an area near Paonia, Colo., as a part of an attempt to alleviate the shortage of known coking coal of good quality in the western United States. Geologic mapping of the area was undertaken by the U. S. Geological Survey with the purpose of first furnishing guidance in location of drillholes and later aiding in interpreting the results of the drilling. The drilling program was under the general supervision of A. L. Toenges of the U. S. Bureau of Mines. J. J. Dowd and R. G. Travis were in charge of-the work in the field. Geologic mapping was started by D. A. Andrews of the Geological Survey in the summer of 1943 and was continued from the spring of 1944 to 1949 by the writer. The first few holes drilled failed to locate coking coal, but in the summer of 1944 coking coal was discovered by drilling 6 miles east of Somerset, Colo., the site of present mining. In the succeeding years, 1945 to 1948, 100 to 150 million tons of coal suitable for coking were blocked out by drilling. The ensuing discussion of the geologic controls on the distribution of coking coal in the area is based on the geologic mapping as well as the drilling done in the Paonia area, more complete descriptions of which have appeared or are in process of publication.1-5 In order that the possible geologic controls affecting the present distribution of coking coal may be considered, it is necessary to discuss briefly the indicators. of coking quality coals. Coking Coal Coal that cokes has the property of softening to form a pastelike mass at high temperatures under reducing conditions in the coke oven. This softening is accompanied by the release of the volatile constituents as bubbles of gas. After release of the contained gases and upon cooling, a hard gray coherent but spongelike mass remains that is referred to as coke. This substance varies greatly in physical properties and, to be suitable for industrial use, must be sufficiently dense and strong to withstand the crushing pressure of heavy furnace loads. Western coals have a generally high volatile content and therefore form a satisfactory coke only when they attain a rather high fluidity during the process of heating and distillation in-the coke oven. When this high degree of fluidity is developed, the volatile constituents escape and leave a finely porous coke. On the other hand, when the degree of fluidity is low the product is an excessively porous and therefore physically weak mass that is called char.6 Small quantities of oxygen present in coal are believed to decrease the fluidity of the material during the coking process and to favor the development of char rather than coke. In consequence, coal chemists have for some time considered the possibility of developing an index to coking. qualities by inspection of chemical analyses of coals.7 A formula has now been developed that does permit a rough preliminary estimate of the cokability of coal on the basis of the analysis on an ash and moisture-free basis. Coals may be eliminated as possible coking fuels if the oxygen content is greater than 11 pct. Similarly the ratio of hydrogen to oxygen must be greater than 0.5 and the ratio of fixed carbon to volatile constituents must be greater than 1.3. If the coal, on the basis of these limiting factors, appears to have possible coking qualities, the following formula permits determination of the coking index: Coking index =[ a+b+c+d 5] a equals 22/oxygen content on ash and moisture- free basis, . b equals two times the hydrogen content divided by oxygen content on moisture and ash-free basis, c equals fixed carbon/1.3 x volatile matter, and d equals the heating value on moist, ash-free basis/13,600. Coking indices higher than 1.0 suggest that the coal will coke, and indices above 1.1 indicate good coking tendencies. Although generally usable, this formula is not completely satisfactory because the percentage of oxygen shown in ultimate analyses is derived only by difference; i.e., by subtracting the sum of the percentages of the constituents determined analytically from 100 pct.8,9 Although the coking index indicates the coking tendencies of coal, it is necessary to make physical tests of coke before its industrial value can be determined. The U. S. Bureau of Mines has developed a standard procedure for determining the approximate strength of coke that would be formed from a given coal. In this test one part of ground coal, mixed with 15 parts of carborundum, is baked to form a standard briquette. The weight, in kilograms, necessary to crush the briquette is termed the agglutinating index. This test determines the relative fluidity attained in the coking process by measuring the cementing strength of the coal in the briquette. A

Jan 1, 1952

By O. N. Carlson, S. A. Bradford

Discontinuous yielding in tensile tests was observed in V-O alloys in the temperature ranges of 150° to 175°C and also 350° to 400°C. The magnitude and intensity of the serrations were found to vary considerably with oxygen content. Maxima were observed in tensile and yield strengths and in the strain-hardening coefficient at the higher temperature only. The strain rate sensitivity was observed to be negative between 150° and 400°C. THIS investigation was undertaken to study the effect of oxygen on the tensile properties of iodide vanadium in the temperature range of 25o to 450°C. Brown1 observed an increase in strength between room temperature and 400°C in vanadium metal, and found that oxygen and nitrogen had a rather pronounced effect on the strength and ductility. A maximum in the tensile strength was observed by Rostoker et al.2 near 300oC and by Pugh3 around 450°C for calcium-reduced vanadium. Pugh also found a maximum in the yield strength and in the strain-hardening exponent, and minima in the elongation and strain rate sensitivity at the same temperature. Eustice and Carlson4 reported the appearance of serrations in the stress-strain curves between 140° and 180°C in iodide vanadium containing 600 ppm O. These anomalies in the mechanical properties indicate that strain aging occurs in vanadium, but the impurity or impurities responsible for the above-mentioned effects have not been identified. The phenomenon of strain aging is usually characterized by the return of the yield point after interruption of a strength test. In the temperature range where strain aging occurs, the yield and tensile strengths attain maximum values, elongation and strain rate sensitivity exhibit minima, and discontinuous yielding is generally observed in the stress-strain curve. Cottrell5, 6 has postulated that strain aging is due to the migration of solute atoms to dislocation sites to produce locking after the dislocations have broken free from their impurity atmospheres during the initial yielding. At the strain-aging temperature the process is a dynamic one in which the solute impurity atoms diffuse to the vicinity of the moving disloca- tion producing "locking" which gives rise to maxima in the tensile strength and serrations in the elongation curves. Cottrel17 has noted that discontinuous yielding in iron occurs when the diffusion coefficient of nitrogen, D, and the strain rate, i, are related by D = 10-9 €. EXPERTMENTAL PROCEDURE The vanadium metal employed in this study was prepared by the iodide refining process as described by Carlson and owen.8 A representative analysis of the vanadium used in this investigation was: 150 ppm O, <5 ppm N, <1 ppm H, 150 ppm C, 150 ppm Fe, 70 ppm Cr, <50 ppm Si, 30ppm Cu, 20 ppm Ni, <20 ppm Ca, <20 ppm Mg and <20 ppm Ti. Alloys containing from 200 to 1800 ppm O, all of which lie in the solid solution range of the V-O system, were prepared by arc melting vanadium together with portions of a high-oxygen master alloy. The master alloy was prepared by tamping pure V2O5 into holes drilled in a vanadium ingot and arc melting this five or six times in an inert gas atmosphere, inverting the button between each melting step. The oxygen content of the master alloy was then determined by vacuum fusion analysis. Vanadium containing less than 150 ppm O was prepared in the following manner. A bar of iodide vanadium was deoxidized by sealing it in a tantalum crucible with a few grams of high-purity calcium. This was held at 1100°C for 4 days to allow time for the oxygen to diffuse to the surface and to react with the calcium vapors. The calcium oxide product was later dissolved from the surface of the bar with dilute acetic acid. In this way vanadium containing from 20 to 50 ppm O was prepared. Sample Preparation. The are-melted ingots were cold swaged into 3/16-in. diam rods and these were machined into cylindrical tensile specimens with a reduced section of 1.00-in. length and 0.120-in. diam. The test specimens were annealed for 4 hr at 900°C in a dynamic vacuum of mm of Hg to remove hydrogen from the metal. This recrystal-lization treatment produced a uniformly fine-grained structure with a mean grain size of approximately 0.06-mm diam. The oxygen contents reported in this paper were determined by a vacuum fusion analysis of the tensile specimens after testing. Analyses for other interstitial or metallic impurities showed no significant changes from that of the original material. Tension Tests. Tension tests were performed on a screw-driven tensile machine at a constant cross-head speed of 0.01 in. per min. Tests at elevated temperatures were carried out by heating the

Jan 1, 1962

By O. Mellgren, A. M. Gaudin, P. L. De Bruyn

The adsorption density of ethyl xanthate on pyrite was determined as a function of xanthate concentration. Surface preparation of the mineral appears to have asafunctionsome effect on the subsequent adsorption process, A monolayer of xanthate on the surface is exceeded only in presence of oxygen. The effect of OH- , HS- (and x and CN- S=)and on the amount of xanthate adsorbed was investigated. Competition between OH- and X- (xanthate) ions for specific adsorption sites is indicated over a wide pH range. IN the flotation of sulfide ores, xanthates are most commonly used to prepare the surface of the mineral to be floated so that attachment to air takes place. The quantity of agent required to make the mineral hydrophobic is usually very small, of the order of 0.1 to 0.25 lb per ton of mineral. Details of the mechanism of pyrite collection are for the most part unsettled. Adsorption of collector has long been believed to involve an ion exchange mechanism as demonstrated for galena&apos; and for chalcocite.2 In the work on chal-cocite it was also demonstrated that a film of xanthate radicals unleachable in solvents that dissolve alkali xanthates, copper xanthate, or dixanthogen was formed at the surface of the mineral. The unleachable product increased with increasing addition of xanthate up to a maximum corresponding to an oriented monolayer of xanthate radicals. Pyrite is extremely floatable with xanthate if its surface is fresh.9 ut the floatability decreases rapidly as oxide coatings increase in abundance. Pyrite shows zero contact angle when in contact with ethyl xanthate solution at pH higher than about 10.5;4 at neutrality, a contact angle of 60" is obtained at a reagent concentration of 25 mg per liter. Alkali sulfides and cyanides are pyrite depressants. In this study of pyrite collection the writers have sought to relate measured xanthate adsorption to the method used in preparing pyrite, to the presence or absence of oxygen, to concentration of hydroxyl, hydrosulfide, sulfide, and cyanide ions. The principal experimental tool has been radioanalysis," " using xanthatcx marked with sulfur 35. Experimental Materials Pyrite: Unlike most sulfides, pyrite is a poly-sulfide. The structure given by Bragg7 resembles that of sodium chloride, the iron atoms corresponding to the position of sodium and pairs of sulfur atoms corresponding to the position of chlorine. The edge of the unit cell in pyrite is 5.40 A and in halite 5.63 A. The S-S distance in pyrite is 2.10 A; the Fe-S distance, 3.50 A: and the Fe-Fe distance, 3.82 A. Natural pyrite from Park City, Utah, was used in this investigation. Pyrite 1 was obtained by hand picking pure crystals. Pyrite 2 and Pyrite 3 were obtained from finer textured crystalline material containing inclusions of silicates. The same cleaning technique was utilized for the preparation of Pyrite 2 and Pyrite 3, whereas a different cleaning technique was used for Pyrite 1. Pyrite 1 was prepared as follows: The crystals were ground in a porcelain ball mill and the 200/400 mesh fraction was separated by wet screening with distilled water, followed by washing for 1 hr with deoxygenated distilled water acidified with sulfuric acid to pH 1.5. The acid was removed by rinsing with deoxygenated distilled water on a filter until a pH of 6.0 was reached in the effluent. This filtration was carried out under nitrogen. The sample was then dried in a desiccator under nitrogen. The period of time for which this pyrite sample was in contact with water containing oxygen was about 4 hr. The specific surface as determined by the BET gas adsorption method was 582 cm2 per g. Final material assayed 53.12 pct sulfur and 46.5 pct iron (theoretical, for FeS,: S, 53.45 pct; Fe, 46.55 pct). After crushing, Pyrite 2 and Pyrite 3 were washed with 1 M HCl. rinsed, and fed to a laboratory shakinq table to remove the small amount of silicates. The concentrate obtained was ground in a laboratory steel ball mill. The 200/400 mesh fraction was separated by classification in a Richards hindered settling tube. This fraction was then given a final wash with 0.1 M HCl and deoxygenated water was filtered through the sample. The final effluent showed a conductivity equivalent to that of a solution having a salt concentration of 0.3 ppm. Aqueous hydrogen sulfide solution was then added to the sampln (about 100 ml saturated H,S solution to about 1000 g pyrite under a few hundred milliliters of water) which was stored wet under nitrogen. The sample stored in this manner showed no indication of formation of iron oxides, whereas iron oxides appeared

Jan 1, 1957

By Vard H. Johnson

IN 1943 the U. S. Bureau of Mines undertook drilling in an effort to develop new reserves of coking coal in an area near Paonia, Colo., as a part of an attempt to alleviate the shortage of known coking coal of good quality in the western United States. Geologic mapping of the area was undertaken by the U. S. Geological Survey with the purpose of first furnishing guidance in location of drillholes and later aiding in interpreting the results of the drilling. The drilling program was under the general supervision of A. L. Toenges of the U. S. Bureau of Mines. J. J. Dowd and R. G. Travis were in charge of the work in the field. Geologic mapping was started by D. A. Andrews of the Geological Survey in the summer of 1943 and was continued from the spring of 1944 to 1949 by the writer. The first few holes drilled failed to locate coking coal, but in the summer of 1944 coking coal was discovered by drilling 6 miles east of Somerset, Colo., the site of present mining. In the succeeding years, 1945 to 1948, 100 to 150 million tons of coal suitable for coking were blocked out by drilling. The ensuing discussion of the geologic controls on the distribution of coking coal in the area is based on the geologic mapping as well as the drilling done in the Paonia area, more complete descriptions of which have appeared or are in process of publication."&apos; In order that the possible geologic controls affecting the present distribution of coking coal may be considered, it is necessary to discuss briefly the indicators of coking quality coals. Coking Coal Coal that cokes has the property of softening to form a pastelike mass at high temperatures under reducing conditions in the coke oven. This softening is accompanied by the release of the volatile constituents as bubbles of gas. After release of the contained gases and upon cooling, a hard gray coherent but spongelike mass remains that is referred to as coke. This substance varies greatly in physical properties and, to be suitable for industrial use, must be sufficiently dense and strong to withstand the crushing pressure of heavy furnace loads. Western coals have a generally high volatile content and therefore form a satisfactory coke only when they attain a rather high fluidity during the process of heating arid distillation in the coke oven. When this high degree of fluidity is developed, the volatile constituents escape and leave a finely porous coke. On the other hand, when the degree of fluidity is low the product is an excessively porous and therefore physically weak mass that is called char." Small quantities of oxygen present in coal are believed to decrease the fluidity of the material during the coking process and to favor the development of char rather than coke. In consequence, coal chemists have for some time considered the possibility of developing an index to coking qualities by inspection of chemical analyses of coals.&apos; A formula has now been developed that does permit a rough preliminary estimate of the cokability of coal on the basis of the analysis on an ash and moisture-free basis. Coals may be eliminated as possible coking fuels if the oxygen content is greater than 11 pct. Similarly the ratio of hydrogen to oxygen must be greater than 0.5 and the ratio of fixed carbon to volatile constituents must be greater than 1.3. If the coal, on the basis of these limiting factors, appears to have possible coking qualities, the following formula permits determination of the coking index: a+b+c+d Coking index = -------- 5 a equals 22/oxygen content on ash and moisture-free basis, b equals two times the hydrogen content divided by oxygen content on moisture and ash-free basis, c equals fixed carbon/l.3 x volatile matter, and d equals the heating value on moist, ash-free basis/13,600. Coking indices higher than 1.0 suggest that the coal will coke, and indices above&apos; 1.1 indicate good coking tendencies. Although generally usable, this formula &apos;is not completely satisfactory because the percentage of oxygen shown in ultimate analyses is derived only by difference; i.e., by subtracting the sum of the percentages of the constituents determined analytically from 100 pct. Although the coking index indicates the coking tendencies of coal, it is necessary to make physical tests of coke before its industrial value can be determined. The U. S. Bureau of Mines has developed a standard procedure for determining the approximate strength of coke that would be formed from a given coal. In this test one part of ground coal, mixed with 15 parts of carborundum, is baked to form a standard briquette. The weight, in kilograms, necessary to crush the briquette is termed the agglutinating index. This test determines the relative fluidity attained in the coking process by measuring the cementing strength of the coal in the briquette. A

Jan 1, 1953

By Royal Jackman

Two comprehensive papers have appeared regarding the forms of copper that occur in smelter slags, one by Frank E. Lathe1 and the other by C. G. Maier and G. D. Van Arsdale.2 These authors comment on other published results and draw conclusions from their own investiga-tions. The development of X-ray examination of minerals and improve-ment in high-power microscopic methods make it possible today to get additional evidence by means that were not available to earlier investi-gators. The present work was confined to reverberatory slags obtained from five different plants. Some definite conclusions were reached regarding the forms of copper present in these slags. In most cases these agree with some of the findings of Maier and Van Arsdale but new methods of attack were used in the investigation.

Jan 1, 1933

By T. H. Alden

T. H. Alden (General Electric Research Laboratory)—This paper as well as earlier ones of Dr. Wood represent an important contribution to the experimental description of fatigue fracture. The mechanism of fracture proposed by the authors, however, is not established by this data nor supported by other data existing in the literature. Although taper section metallography provides a rather detailed picture of fatigue crack geometry, photographs so obtained must be interpreted with care. The narrow bands revealed by etching, frequently associated with surface notches, are labeled by the authors "fissures". Measurement shows, taking into account the 20 to 1 taper magnification, that the depth of these structures is at most 2 to 3 times the width. This distinction is important in the conception of a mechanism of crack formation. It is difficult, for example, to imagine a deep, narrow fissure arising from a "ratchet slip" model. A surface notch, on the other hand, may form easily by this mechanism. The notches observed in the present work are the subsurface evidence of the surface slip bands or striations in which fatigue cracks are known to originate.4-6 It is clear that an understanding of the structure of these slip bands is of key importance in understanding the mechanism of fracture. The evidence presented shows that these regions etch preferentially, possibly because they contain a high density of lattice defects, or as the authors state equivalently, because they are "abnormally distorted." However, it is not possible to conclude that the distortion consists of a high density of vacant lattice sites. The fact of a high total shear strain in itself does not assure a predominance of point defects as opposed to other defects, for example, dislocations. Other evidence in the literature which suggests unusual densities of point defects formed by fatigue7-&apos; refers not to the striations or fissures, but to the material between fissures (the "matrix"). If a choice must be made, the preferential etching would seem to be evidence for a high dislocation density, since dislocations are known to encourage chemical attack in copper;g no such effect is known for the case of point defects. A third alternative is that the slip bands are actually cracked, but that near its tip the crack is too narrow to be detected by the authors&apos; metal-lographic technique. In this case the rapid etching can be readily understood in terms of the increased chemical activity of surface atoms. Unless a vacancy mechanism is operative, the motion of dislocations to-and-fro on single slip planes will not lead to crack growth. Point defect or dislocation loop generation are the principal non-reversible effects predicted by this model. In any case, the nonuniform roughening of the surface in a slip band6 requires a flexibility of dislocation motion which is not a part of the to-and-fro fine slip idea. The same is probably true of crack growth by a shear mechanism. Either some dislocations must change their slip planes near the end of the band and return on different planes,&apos;0 or dislocations of opposite sign annihilate." The mechanism by which these processes occur in copper at room temperature or below is that of cross slip. Thus cross slip appears to be essential to fatigue crack growth.6&apos;10"12 The fact that a tensile stress opens the slip bands into broad cracks does not indicate the structure of the bands or the mechanism by which cracks form. The charactersitic concentration of slip into bands during fatigue shows a low resistance to shear strain in these regions. (This fact in itself may be inconsistent with a high concentration of vacancies.) The authors contend also that continuing shear produces an additional mechanical weakening so that the bands fracture easily (are pulled apart) under the influence of the superimposed tensile stress. It is equally possible that the only weakness is a weakness in shear, that the crack propagates by a shear mechanism, and that subsequently the tensile stress pulls the crack apart. Even the direct observation of bands opened by a tensile stress would not be conclusive since, as argued above, they may be fine cracks. The same argument applies to internal cracks, their existence in the presence of a tensile stress not indicating the mechanism of formation. Internal cracks originating in regions of heavy shear have also been seen following tensile deformation of OFHC copper,13 so that this mode of fracture is not unique to combined tensile and fatigue straining. The authors point out in their companion report14 that 90 pct of the cracks formed during pure tor-sional strain were within 8 deg of the normal to the specimen axis. If the tensile stress were an important factor in crack propagation, it is surprising that the cracks cluster about the plane in which the normal stress vanishes. Similarly, a study of zinc single crystals showed that for various orientations the life correlated well with the resolved shear stress on the basal plane,&apos;= and was not dependent on the normal stress across this plane. W. A. Wood and H. M. Bendler (Authors&apos; reply) -Dr. Alden&apos;s discussion emphasizes the essential point in the relation of slip band structure to

Jan 1, 1963